O
W
N
E
R
’
S
M
A
N
U
A
L
AGP-2
ONBOARD ACOUSTIC GUITAR PREAMP
ABGP
ONBOARD ACOUSTIC BASS GUITAR PREAMP
Download from Www.Somanuals.com. All Manuals Search And Download
ONBOARD ACOUSTIC GUITAR PREAMP
WARNING
INSTALLATION BY A QUALIFIED PROFESSIONAL REPAIRMAN IS STRONGLY
RECOMMENDED. FISHMAN TRANSDUCERS WILL NOT BE RESPONSIBLE FOR ANY
DAMAGES TO YOUR INSTRUMENT DUE TO IMPROPER INSTALLATION.
2. TEMPLATE
A drilling template is provided for drilling the control shaft holes. Cut out the
template outline. Check that it fits between the upper and lower linings
when held inside the guitar at the chosen location. Tape the template at the
location on the outside of the guitar. With a sharp scribe, pierce the tem-
plate at the marks. Remove the template. This should provide you with two
drilling centers marked on the side of the guitar. These centers will be
1.250 inch (31.8mm) apart. At each center, drill a .375 inch (9.5mm) hole
through the side of the guitar. We recommend using a sharp 3/8 inch spur
bit for this operation.
FIG. 1
3. SPACER BLOCK
We strongly advise that a
wooden spacer block (see
Figure 1) be used to add
strength to the mounting area
of the guitar and to more evenly
distribute the load of the pre-
amp. We do not recommend
using a hex nut and lock washer as the inside bearing surface to accommo-
date the thickness of the inside of your instrument because this could result
in possible damage to the instrument itself
4. PREPARING THE SPACER
Using the drilling template as a guide, make a rectangular wooden spacer
that is 2.00 inch x .750 inch x T (50.8mm x 19.0mm x T). T is the measure-
ment derived from the protruding bushing length minus the outside hard-
ware thickness (Figure 1) To derive T, insert the control shafts through the
Download from Www.Somanuals.com. All Manuals Search And Download
3
AGP-2 / ABGP
holes from the inside of the guitar. Next, measure the length of the threaded
bushing that protrudes out from the side of the instrument. From this mea-
surement, subtract the thickness of the outside hardware (hex nut and finish
washer).
FIG. 2
5. WIRING THE TRANSDUCER
Remove the cover from
the AGP-2 Preamp.
Locate the terminal block
with two sections to be
used to connect the
transducer leads (see
Figure 2). Thread the
transducer wire through
the rubber grommet
where the wire harness
enters the preamp. Strip
and tin the signal and ground wires from the transducer and connect them
to the terminal block as shown in Figure 2. Check for shorts. Replace the
cover and screws (SEE NEXT SECTION), being careful to engage the grom-
met in the appropriate slot.
6. MOUNTING THE BATTERY HOLDER
The AGP-2 is supplied with a battery holder that can be attached to the pre-
amp cover with the screws provided (see Figure 3), or be attached to the
neck block (see Section 6a).
Be sure to check and adjust the fit of the battery in the holder before
installing the AGP-2 Preamp inside the instrument.
6a. OPTIONAL BATTERY HOLDER MOUNT
Cut a block of 1/4” plywood approximately 1-1/2” x 2-1/2” (40mm x 65mm).
Using two Number 4 pan-head sheet metal screws (1/4" length), attach the
battery holder to the wooden block. The assembly can then be attached to
the neck block with wood glue, double sided tape, or Velcro.
Download from Www.Somanuals.com. All Manuals Search And Download
4
ONBOARD ACOUSTIC GUITAR PREAMP
IMPORTANT
Although the supplied battery holder should provide adequate capacity to grip the bat-
tery at all times, we strongly recommend removal of the battery when shipping or flying
with your instrument. FAILURE TO REMOVE BATTERY COULD RESULT IN DAMAGE TO
YOUR INSTRUMENT. Fishman will not be held responsible for any such damage as a
result of shipping or handling.
7. MOUNT THE PREAMP
Slip the wooden spacer block (prepared earlier) over the control bushings
and mount the preamp. The outside hardware should include a smooth 3/8”
dress washer and a 3/8” hex nut. Tighten the hex nut.
8. PREPARE THE ENDBLOCK
The objective of this method is to drill a hole for the jack into the endblock,
with the endpin in place. You may remove a loose endpin and refasten it
with cyanoacrylate glue before starting this procedure.
1. Apply masking tape around the endblock area to protect the instrument.
2. Cut the endpin with an X-Acto
saw blade 1/16" away from the
body.
3. Centerpunch a guide hole in the
center of the trimmed endpin.
4. Drill a 1/8" pilot hole through
the endblock.
5. Line up the 15/32" Spade bit in
the pilot hole and begin drilling.
Maintain a perpendicular plunge
in relation to the instrument.
Use steady (but not heavy)
pressure, especially as the drill
exits inside the guitar.
IMPORTANT: To avoid damage to
the instrument, let the drill come
to a complete stop before remov-
ing it from the hole.
Download from Www.Somanuals.com. All Manuals Search And Download
5
AGP-2 / ABGP
9. WIRING THE OUTPUT JACK
Solder the red wire to the tip (short terminal).
Solder the black wire to the ring (longer terminal).
Solder the shielding to the ground tab.
After soldering, bend the strain relief tabs around the grey jacket.
10 - FASTEN THE JACK IN THE ENDPIN HOLE
Follow this sequence when installing the endpin jack:
1 - Shielding Cap (optional)
2 - First Large Hex Nut
3 - Large Dress Washer
4 - Star Washer
5 - Guitar Endblock
6 - Small Dress Washer
7 - Small Dress Nut
8 - Strap Button
The jack should protrude at least 5/16" and no more than 11/32" outside of
the guitar body for proper fit.
After fitting the small dress washer and nut over the end of the jack, insert
the 3/32" allen wrench through the small hole on the end of the jack.
Tighten the nut with the 1/2" open end wrench while holding the jack in
place with the allen wrench.Thread and hand tighten the the strap button.
NOTE: With the strap button in place, the end of the
jack should protrude slightly to allow proper plug fit.
Download from Www.Somanuals.com. All Manuals Search And Download
6
ONBOARD ACOUSTIC GUITAR PREAMP
11. KNOB ALIGNMENT
The stacked knob set controls treble boost & cut (small knob) and bass
boost & cut (large knob). Both knobs have a center-detent to indicate flat
position. Place the bass (large outer ring) knob onto the stacked shaft so
that the two inner protrusions slide into the corresponding slots on the outer
shaft. Now place the smaller treble knob onto the inner shaft. The white
position markers should align with each other in the center detent position.
Now place the large volume knob onto the appropriate shaft; rotate the knob
and remove to re-position the line if necessary for the desired sight refer-
ence position.
12. READY FOR USE
The power is switched on only when a 1/4” mono guitar cable is plugged into the out-
put jack. The AGP-2 features a “soft” turn on mode. This means that the unit powers
up gradually over several seconds once the instrument is plugged in.
SPECIFICATIONS
SYSTEM GAIN
9 dB (input to output at 1 kHz)
All tone controls flat.
Maximum input voltage before clipping with all controls at full boost
.8V P-P
AGP-2 TONE CONTROLS
Treble: Boost and Cut
± 3dB at 1700 Hz
± 14dB at 20 kHz
Bass: Boost and Cut
± 3dB at 350 Hz
± 8dB at 50 Hz
Frequency Response
ABGP TONE CONTROLS
Treble: Boost and Cut
20 Hz to 20 kHz ±2dB All tone controls flat
± 3dB at 850 Hz
± 14dB at 20 kHz
Bass: Boost and Cut
± 3dB at 350 Hz
± 8dB at 50 Hz
Frequency Response
POWER SUPPLY
Battery Life
20 Hz to 20 kHz ±2dB All tone controls flat
9 Volts (battery not included)
150 hours continuous use (alkaline battery)
All specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download
7
LIMITED WARRANTY
The FISHMAN AGP-2 ACOUSTIC GUITAR PREAMP is warranted to function for a period
of One (1) Year from the date of purchase. If the unit fails to function properly within the
warranty period, free repair and the option of replacement or refund in the event that
FISHMAN is unable to make repair are FISHMAN’s only obligations. This warranty does
not cover any consequential damages or damage to the unit due to misuse, accident, or
neglect. FISHMAN retains the right to make such determination on the basis of factory
inspection. Products returned to FISHMAN for repair or replacement must be shipped in
accordance with the Return Policy, as follows. This warranty remains valid only if repairs
are performed by FISHMAN. This warranty gives you specific legal rights and you may also
have other rights which may vary from state to state.
RETURN POLICY
To return products to FISHMAN TRANSDUCERS, you must follow these steps...
1. Call FISHMAN TRANSDUCERS at 978-988-9199 for a Return Authorization Number
(“RAN”).
2. Enclose a copy of the original Bill of Sale as evidence of the date of purchase, with
the product in its original packaging and a protective carton or mailer.
3. FISHMAN TRANSDUCERS’ technicians will determine whether the item is covered by
warranty or if it instead has been damaged by improper customer installation or other
causes not related to defects in material or workmanship.
4. Warranty repairs or replacements will be sent automatically free of charge.
5. If FISHMAN TRANSDUCERS determines the item is not covered by warranty, we will
notify you of the repair or replacement cost and wait for your authorization to
proceed.
FISHMAN TRANSDUCERS®
340-D Fordham Road Wilmington MA 01887 USA
Phone 978-988-9199 • Fax 978-988-0770
009-061-001 12-98
Download from Www.Somanuals.com. All Manuals Search And Download
|