TM
My Little Desk Bed
Model Number: 79415
Instructions
Please read these instructions and keep them for future reference.
Adult assembly is required.
My Little Desk Bed is recommended for children who are at
least 15 months old and are ready to progress from a crib to a bed,
including being able to get on and off a bed unassisted.
Maximum weight: 50 lbs.
Tools needed for assembly: Hammer and Two Phillips Screwdrivers.
Download from Www.Somanuals.com. All Manuals Search And Download.
Toddler Bed Assembly
2
CAUTION
Metal Tab
Showing
Please keep small parts and
plastic bags out of children’s reach.
Dispose of plastic bags properly.
INCORRECT
CORRECT
1
• Check to be sure the crimped mattress tubes are inserted
properly.
• There is a metal tab on one side of the crimped end. Make
sure the metal tab is not showing.
Straight Side Rail
• Pull up firmly on the crimped mattress tubes to be
sure they are securely in place.
Crimped Mattress Tube
• If the crimped mattress tubes can be removed from the
1
straight side rail, re-read and repeat step
.
3
Mattress Tube
Crimped Mattress Tubes
Mattress Tube
Straight Side Rail
Helpful Hint: The assembly of the crimped mattress
tubes to the straight side rail is permanent. Once assembled
properly, you will be unable to remove the crimped mattress
tubes.
Straight Side Rail
• Place one of the straight side rails on a soft, flat surface.
• Insert a crimped mattress tube into each slot in the straight
side rail.
• Insert the mattress tube into the hole in the straight side rail.
• Tap the ends of the crimped mattress tubes with a hammer
until they snap into place.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Toddler Bed Assembly
6
4
Straight Side Rail
Crimped Mattress Tube
Mattress Tube
Crimped Mattress Tubes
Screw Holes
Curved Ends
Crimped Mattress Tubes
• Position the other straight side rail so that the screw holes
on each straight side rail are on the same side.
Helpful Hint: The assembly of the crimped mattress tubes
to the straight side rail is permanent. Once assembled prop-
erly, you will be unable to remove the straight side rail.
Mattress Tube
• Repeat steps
remaining crimped and regular mattress tubes.
• Make sure the curved ends of the curved side rails are on
the same side.
Curved Side Rail
to assemble the curved side rails and
• Fit the slots and hole in the straight side rail onto the
mattress tubes.
• Push down on both ends of the straight side rail to be sure
the crimped mattress tubes snap into place.
-
1
5
5
INCORRECT
CORRECT
7
Curved Side Rail
Straight Side Rail
Metal Tab
Showing
• Check to be sure the crimped mattress tubes are inserted
properly.
• There is a metal tab on one side of the crimped end. Make
sure the metal tab is not showing.
Straight Side Rail
Curved Side Rail
• Pull up firmly on the straight side rail to be sure the
mattress tubes are securely in place.
• If the straight side rail can be removed from the crimped
• Place both metal frame assemblies on a flat surface.
• Insert the straight side rails into the curved side rails, as
shown.
mattress tubes, re-read and repeat step
.
4
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Toddler Bed Assembly
Mattress Retainer
8
10
Headboard
®
Metal Frame
Right Side Panel
Left Side Panel
#10 – 24 x 11/4" Screw
Shown Actual Size
• Stand the headboard assembly upright, as shown.
• Push down on the top of the headboard to secure it to the
right and left side panels.
• Locate the holes in the metal frame, near the middle.
Helpful Hint: If you are having difficulty securing the
headboard to the left and right side panels, position the
assembly against a wall (with the molded moon, sun
and star toward the wall). Push down on the top of the
headboard to secure it to the left and right side panels.
• Position a mattress retainer so that the arrow is pointing
up and is over the hole on the inside of the metal frame
assembly.
• Insert a barrel nut through the mattress retainer and into the
inside of the metal frame.
• Insert a 11/4" screw into the outside of the metal frame and
hand tighten the hardware.
11
• While holding the barrel nut in place with a Phillips screw-
driver, tighten the screw with the other Phillips screwdriver.
Do not over-tighten.
Metal
Frame
• Repeat this procedure to attach the other mattress retainer
to the other side of the metal frame.
9
Headboard
Left Side Panel
Straight End
Groove
Pegs
Slots
Right Side Panel
• Position the headboard on a flat surface with the molded
moon, sun and star facing up.
• Position the right side panel with the R facing the
headboard.
Left Side Panel
Right Side Panel
Headboard
• Fit the pegs on the headboard into the slots in the right
side panel.
• Turn the headboard assembly backward, as shown.
• Position the metal frame with the straight ends downward,
and the curved ends pointing forward, as shown.
• Repeat this procedure to attach the left side panel to the
headboard.
• Insert the metal frame straight ends into the grooves in the
left and right side panels.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Toddler Bed Assembly
12
14
Footboard
Metal Frame
F
i
sh
er
-P
ri
ce
®
Metal Frame Curved End
Groove
• Fit the metal frame curved ends into the grooves in the
footboard.
15
• Push down on the metal frame to completely insert it into
the grooves in the left and right side panels.
13
F
is
h
e
r
-P
ri
®
c
e
Screws
Footboard
• Insert four barrel nuts into the metal frame curved ends.
• Insert four screws into the outside of the footboard and
hand tighten the hardware.
• While holding a barrel nut in place with a Phillips screw-
driver, tighten the screw with the other Phillips screw-
driver. Do not over-tighten. Repeat this procedure to tighten
the other screws.
Barrel Nuts
Screws
Left Side Panel
• Insert two barrel nuts into the metal frame located on the
inside of the left side panel, as shown.
• Insert two screws into the outside of the left side panel and
hand tighten the hardware.
Toddler bed assembly is now complete.
• While holding a barrel nut in place with a Phillips screwdriv-
er, tighten the screw with the other Phillips screw-
driver. Do not over-tighten. Repeat this procedure to tighten
the other screw.
• Repeat this step to secure the right side panel to the
metal frame.
• Turn the assembly right side up.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Converting the Toddler
Bed to a Desk
Desk Assembly
1
Left Side Panel
Right Side Panel
Pegs
F
is
h
e
r-
P
r
®
ic
e
Slots
Desk
• Position the desk on a flat surface with the molded moon,
sun and star facing down.
• Position the right side panel with the R facing the desk.
• Fit the pegs on the desk into the slots in the right side
panel.
• The My Little Desk BedTM easily disassembles to convert to a
desk.
• Remove the barrel nuts and screws (eight of each) from the
left side panel, right side panel and footboard.
• Repeat this procedure to attach the left side panel to the
desk.
• Remove the headboard, left and right side panels and foot-
board from the metal frame.
IMPORTANT! Do not attempt to disassemble the metal
frame. Please store the metal frame with barrel nuts
and screws in a safe place for future use.
2
Desk Assembly
Desk Top
(was
Footboard)
Desk (was
Headboard
Desk
Right Side Panel
Left Side Panel
Right Side Panel
Left Side Panel
• Stand the desk assembly upright, as shown.
• Push down on the top of the desk to secure it to the left
and right side panels.
Helpful Hint: Because you are assembling a desk, we have
Helpful Hint: If you are having difficulty securing the desk
to the left and right side panels, position the assembly
against a wall (with the molded Fisher-Price logo toward
the wall). Push down on the top of the desk to secure it to
the left and right side panels.
converted the names of some of the parts in this section.
• The headboard is now the desk.
• The footboard is now the desk top.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Desk Assembly
Care
• Wash all parts with a mild cleaning agent and damp cloth.
Do not use bleach. Rinse with clean water to remove
residue.
3
Desk Top
• Periodically check My Little Desk BedTM for loose fasteners
and tighten as needed.
Groove
Peg
Groove
Peg
One (1) Year
Limited Warranty
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, New York
14052, warrants that My Little Desk BedTM is free from all
defects in material and workmanship when used under
normal conditions for a period of one (1) year from the date
of purchase.
Should the product fail to perform properly, we will repair
or replace it at our option, free of charge. Purchaser is respon-
sible for shipping the product to Fisher-Price Consumer
Affairs at the address indicated above and for all associated
freight and insurance cost. Fisher-Price, Inc. will bear the
cost of shipping the repaired or replaced item to you.This
warranty is void if the owner repairs or modifies the product.
This warranty excludes any other liability other than that
expressly stated above including but not limited to any
incidental or consequential damages.
Desk
• Position the desk top so that the grooved side is toward the
desk.
• Fit the pegs on the desk into the grooves in the desk top.
4
Desk Top
SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION
MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS
AND YOU MAY ALSO HAVE OTHER LEGAL RIGHTS
WHICH VARY FROM STATE TO STATE.
If you have any questions about this product:
In Canada, call 1-800-567-7724, or write to:Mattel/Fisher-Price,
6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
In Great Britain, telephone 01734 770488.
In Australia, call the Fisher-Price Australian Consumer Advisory Service
toll-free at 1-800-800-812, or write to:Fisher-Price, Mattel Pty. Limited,
461 Plummer Street, Port Melbourne,Victoria 3207.
• Rotate the desk top down.
Helpful Hint: When converting the desk back to a toddler
bed, rotate the desk top upright and lift to remove it from
the desk.
Desk assembly is now complete.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|