™
Healthy Care
High Chair
Product features and decoration may vary from the photo above.
Model Number: B8866
Please read these instructions before assembly and use of this product.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver (not included).
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
e
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Note: Tighten all screws with a Phillips screwdriver. Do not over-tighten the screws.
Pad
Toy
Food Tray
Base Tray
Seat Back
Seat
Bottom
Frame
#10 x 2.2 cm (7/8")
Black Screw
Hinge
Rod
#8 x 2 cm (3/4") Screws
2 Seat Bottom Tubes
4 Screw Retainers
#8 x 1.9 cm
(3/4")
Screws
#10 x 2.2 cm (7/8")
Black Screw - 4
#8 x 1.9 cm (3/4") Screws
Frame
Footrest
2 Bases
#10 x 2.2 cm (7/8")
Black Screws
#8 x 1.9 cm (3/4") Screw - 8
SHOWN ACTUAL SIZE
#10 x 2.2 cm (7/8") Black Screw - 7
SHOWN ACTUAL SIZE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
IMPORTANT! Before assembly, inspect this product for
damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing, damaged
or broken. Contact Mattel for replacement parts and
instructions if needed. Never substitute parts.
Seat
Bottom
Tubes
Footrest
Plastic
Rings
Seat Bottom
Plastic
Rings
3
• Align the holes in the plastic
rings and the seat bottom tubes.
• Insert a #8 x 1.9 cm (3/4") screw
into each plastic ring and tighten.
#8 x 1.9 cm (3/4") Screw- 4
SHOWN ACTUAL SIZE
1
• Push the seat bottom tubes back and forth to be sure they
are secured to the seat bottom. If the seat bottom tubes
move, you have probably not fastened them properly.
Remove the screws and check to be sure the screw holes in
the seat bottom tubes and seat bottom plastic rings are
aligned. Replace and tighten the screws.
• Place the seat bottom face down on a flat surface.
• At an angle, fit the footrest on the seat bottom, as shown.
Plastic
Rings
Footrest
Seat Bottom Tubes
Insert Screws
Here
Plastic
Rings
2
• Slide a seat bottom tube through each set of plastic rings
on the seat bottom.
4
#10 x 2.2 cm (7/8")
Black Screw - 2
SHOWN ACTUAL SIZE
• Insert two #10 x 2.2 cm (7/8")
black screws through the foot-
rest and into the seat bottom.
• Tighten the screws.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Frame Leg
Seat Back
Pin
Seat Back
Pin
Opening
Opening
7
Seat
Bottom
Assembly
• Pull the frame leg out on each frame to open. Make sure it
5
“clicks” into place.
• Turn the seat bottom assembly upright.
• Fit the seat back pins into the openings in the top side of
the seat bottom assembly.
#10 x 2.2 cm (7/8")
Black Screw
SHOWN ACTUAL SIZE
Hinge
Hinge Rod
6
• Turn the seat assembly face down.
• Insert the hinge rod through the hinge on the seat back
and seat bottom, as shown.
• Insert a #10 x 2.2 cm (7/8") black screw into the hinge rod
and tighten.
• Set the seat assembly aside for Assembly step 10.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Frame
Decorated
Side
Seat Height
Adjusters
Position 4
Frame
Back
Legs
Press Lever
Base Hole
9
Screw
Retainers
• While pressing the levers on the seat height adjusters, lift
them to position 4 on the frame front legs, as shown.
Base Hole
8
Seat Assembly
#10 x 2.2 cm (7/8")
Black Screw - 2
SHOWN ACTUAL SIZE
Screw Retainer - 2
• Position a frame so that the decorated side is outward.
• Insert the back legs of a frame into one of the bases.
• Fit a screw retainer over the hole in the base, as shown.
Sockets
Sockets
• Insert a #10 x 2.2 cm (7/8") black screw into the screw
retainer and tighten.
• Repeat this procedure to fasten the other frame back leg
to the other side of the base with a screw retainer and
#10 x 2.2 cm (7/8") black screw.
Seat Bottom
Tubes
Hint: The #10 x 2.2 cm (7/8") black screws may have been
assembled to the screw retainers.
10
• Fit the seat assembly between the two frames.
• Insert the seat bottom tubes into the sockets in each seat
height adjuster.
Hints:
• Be sure the seat height adjusters are in the same position
(position 4).
• You may need to push the frames apart slightly to fit the seat
bottom tubes into the seat height adjuster sockets.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Push
Seat
Height
Adjuster
Push
Seat
Height
Adjuster
Front Leg
Holes
Seat Bottom
Tube Ends
12
Screw Retainers
#8 x 1.9 cm (3/4")
Screw - 2
SHOWN ACTUAL SIZE
• Push each seat height adjuster
to be sure they are completely
on the seat bottom tubes.
• Insert a #8 x 1.9 cm (3/4") screw into each seat height
adjuster and the ends of the seat bottom tube.
• Tighten the screws.
Base
11
#8 x 1.9 cm (3/4")
Screw - 2
SHOWN ACTUAL SIZE
#10 x 2.2 cm (7/8")
Black Screw - 2
SHOWN ACTUAL SIZE
Seat
Height
Adjuster
Seat
Height
Adjuster
Screw Retainer - 2
• Fit the frame front legs into the other base.
• Fit a screw retainer over a hole in the base.
• Insert a #10 x 2.2 cm (7/8") black screw into the screw
retainer and tighten.
• Repeat this procedure to fasten the other end of the base
with the remaining screw retainer and #10 x 2.2 cm (7/8")
black screw.
Seat
Bottom
Tube Ends
13
Hint: The #10 x 2.2 cm ( 7/8") black screws may have been
assembled to the screw retainers.
Back and
Bottom View
• From the back and bottom of the assembly, insert a
#8 x 1.9 cm (3/4") screw through both seat height adjusters
and the ends of the seat bottom tube.
• Tighten the screws.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pad
Slot
Crotch
Belt
Elastic Loops
Hole
Hole
15
• Insert the crotch belt through the slot in the pad. Make
sure the crotch belt is not twisted.
Shoulder
Portion
Front View
Tabs
Elastic Loops
14
Back and
Bottom View
• Lift the assembly upright.
• From the front of the assembly, place the pad onto the seat.
16
• Lift the bottom of the pad. Insert the two elastic loops on
the pad through the holes in the seat bottom.
• Fold the top of the pad down.
• Remove the shoulder portion of the waist/shoulder belts
by feeding them through the slots in the seat back.
• From the back and bottom of the seat, hook the elastic
loops to the tabs on the seat.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Upper Shoulder
Belt Slots
Shoulder
Portion
Bottom Slots
17
Lower Shoulder
Belt Slots
18
• Lift the top of the pad.
• Thread the waist/shoulder belts through the bottom slots in
the back of the seat pad.
• Insert the shoulder portion of the shoulder/waist belt
through the slots in the pad and seat back.
- Use the lower shoulder belt slots for a smaller baby.
- Use the upper shoulder belt slots for a larger baby.
• Fit the top of the pad over the seat back.
• Fold the bottom edge of the pad under the edge of the
seat bottom to fasten.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Securing Your Child
IMPORTANT!
• Before each use, inspect this product for damaged hardware,
loose joints, missing parts or sharp edges. DO NOT use if any
parts are missing, damaged or broken. Contact Mattel for
replacement parts and instructions if needed. Never
substitute parts.
Pad Strap
Handle
Elastic
Loop
Elastic
Loop
• Place the high chair on a level, stable surface away from
electrical flexes. Be sure to keep electrical flexes out of
child‘s reach.
Tab
Belt
Ends
WARNING
Tab
Prevent serious injury or death
from falls or sliding out.
The child should at all times wear
a safety harness correctly fitted
and adjusted.
19
Back View
Waist/Shoulder
Belt
Waist/Shoulder
Belt
• From behind the seat, be sure the shoulder portion of the
waist/shoulder belts are secure in the seat back slots.
• Fit the pad strap through the handle and press it to the
fastener on the back of the seat.
• Hook the elastic loops on each side of the pad onto the tabs
in the seat back.
Assembly is now complete.
Crotch
Belt
1
• Place your child in the seat. Position the crotch belt between
your child’s legs.
• Fasten both waist/shoulder belts to each side of the crotch
belt. Make sure you hear a "click" on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing Your Child
Anchored
End
Anchored
End
A
B
B
Free End
A
Free End
Buckle
2
Tighten
Loosen
To tighten the waist belts:
• Feed the anchored end of the waist belt up through the
A
buckle to form a loop
.
B
• Pull the free end of the waist belt
.
• Repeat this procedure to tighten the other waist belt.
To loosen the waist belts:
• Feed the free end of the waist belt up through the buckle to
4
A
form a loop
.
• Enlarge the loop by pulling on the end of the loop toward
the buckle.
To change shoulder belt slots:
• From the back of the high chair, push the shoulder portion
of the waist/shoulder belts through the seat back slots.
• Pull the anchored end of the waist belt to shorten the free
B
end of the waist belt
.
• Repeat this procedure to loosen the other waist belt.
Shoulder
Portion
Hold
Adjuster
Slide
Pull Strap
Adjuster
Down
Down
3
Tighten
Loosen
5
To tighten the shoulder belts: Hold the adjuster and pull
the front shoulder strap down.
To loosen the shoulder belts: Slide the adjuster down.
Note: After adjusting the restraint system to fit your child,
make sure you pull on it to be sure it is securely fastened.
• From the front of the high chair, pull the shoulder portion of
the waist/shoulder belts out and then fit them back through
the desired shoulder belt slots in the headrest pad, seat pad
and the seat back. Pull on the belts to be sure they are
secure in the seat back.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Trays
WARNING
Hint: The base tray can be adjusted for your child’s comfort
two ways (see steps 7 and 8)!
Prevent serious injury or death
from falls or sliding out.
The tray is not designed to hold
the child in the chair.
Base
Tray
Base Tray
Release Bar
7
Armrest
Armrest
• While pushing the release bar on the front of the base tray,
adjust the base tray forward or backward.
Base
Tray
Squeeze
Latch
Squeeze
Latch
6
• Fit the base tray onto the seat armrests. Push down until
the base tray "snaps" into place.
Hint: Before use, thoroughly wash all parts (the trays) that
may contact food.
8
• While squeezing the latches underneath the base tray,
adjust the base tray forward or backward.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Trays
Hint: The base tray can be removed two ways (see steps
9 and 10)!
Food Tray
Base
Tray
Base
Tray
Squeeze
Latch
Squeeze
Latch
11
9
• Fit the food tray into the base tray, as shown.
Hint: Before use, thoroughly wash all parts (the trays) that may
contact food.
• Squeeze one or both of the latches underneath the base
tray and lift.
Base
Tray
Release
Bar
10
• While pushing the release bar on the front of the base tray,
pull the tray base towards you and remove.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Seat
WARNING
Hint: Adjust the seat angle to any of three positions: Upright,
Semi-Recline or Recline.
Prevent serious injury or death
from falls or sliding out.
Upright
Semi-Recline
It is recommended that the high
chair be used in the upright position
only by children capable of sitting
upright unassisted.
Recline
Hint: Adjust the seat height to any of seven positions!
Seat Height
Adjuster
13
To adjust the seat angle:
Press Lever
• Squeeze the seat back
handle and push the seat
back forward or, pull it
backwards to the
desired position.
Squeeze
12
• Push the seat back to be
sure it is latched in position.
Back View
To adjust the seat height:
• Press the levers on both seat
height adjusters and lift or lower
the seat to the desired height.
4
• Make sure both sides of the seat
are adjusted to the same height.
Push the seat bottom to be sure the seat is locked in place.
Note: Make sure there is nothing obstructing the seat
height adjusters.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
Care
• The pad, toy, frame and base tray may be wiped clean using
a mild cleaning solution and a damp cloth. Do not immerse
the base tray.
• The food trays are dishwasher safe. Simply remove the food
tray from the base tray and place in your dishwasher.
IMPORTANT! Never use this product without the restraint
system. Replace the waist/shoulder belts and crotch belt.
Base
Tray
Hole
Peg
14
• Fit the holes on the base tray latches onto the pegs on the
back of the high chair frame.
Pull Frame
Release Latch
15
• With the legs all the way open, lower the seat to position 1
(the lowest position).
• Pull the frame release latches forward and push the rear legs
toward the front legs.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Fisher-Price, Inc., a subsidiary of Mattel, Inc.
East Aurora, New York 14052, U.S.A.
©2003 Mattel, Inc. All Rights Reserved.
® and TM designate U.S. trademarks of Mattel, Inc.
Printed in China
B8866a-0726
Download from Www.Somanuals.com. All Manuals Search And Download.
|