Consumer Information
®
Questions? We’d like to hear from you!
Call Fisher-Price® Consumer Relations, toll-free at 1-800-432-KIDS (5437), 8 AM - 6 PM EST Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470.
Grow to Pro Basketball
Model Numbers: 72408, H5556
Or, write to:
Fisher-Price® Consumer Relations
636 Girard Avenue
East Aurora, New York 14052, U.S.A.
For countries outside the United States:
CANADA
Product features and decoration may vary from the photograph above.
Questions? 1-800-567-7724, Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
GREAT BRITAIN
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500302.
AUSTRALIA
Tool required for assembly: Phillips Screwdriver (not included).
Water or sand to fill base (not included).
Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
IMPORTANT! Rim height should be adjusted only by an adult.
NEW ZEALAND
16-18 William Pickering Drive, Albany 1331, Auckland.
ASIA
Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China.
© 2004 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
PRINTED IN MEXICO
72408e-0920
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Assembly
Rectangular Tab
7
Rim
11
Collar
9
5
PULL HERE
®
-Price
Fisher
Upper Post
4
Peg
PRESS HERE
Grooves
Rim
Lever
Opening
Hole
5
6
Lower
Post
Peg
Peg
Top View
• Move to the side of the assembly.
Back View
Note: The collar may already be factory assembled.
• Place your foot on the base to hold it steady.
• While holding the ring assembly and rim together,
turn them over.
• Press down firmly on the lower backboard while
rotating the backboard up.
• Align the lever on the side of the collar with the
opening in the top of the lower post.
• Insert four screws into the holes in the rim, making
sure each hole in the rim is still aligned with each
screw hole in the net assembly.
• Partially tighten the screws with a Phillips screwdriver.
Turn the rim over to ensure that the net loops are still
in the grooves and through the ring tabs before
completely tightening the screws. Do not over-tighten
the screws.
• When properly assembled, the pegs on the upper
post rest in the grooves in the backboard, as shown.
• Fit the collar onto the lower post, making sure the peg
on each side of the collar snaps into the hole on each
side of the post.
• Hook the rectangular tab on each side of the rim to
the upper post, as shown.
• Rotate the rim down until it snaps into place on
the upper post. Push down on the rim to be sure
it is secure.
Note: The height of the rim is three feet as assembled.
Peg
12
10
Wall
Peg
Backboard
8
Fisher-Price®
Rim
Curved
End
6
Logo
4
Lower Post
4
Upper Post
4
Holes
5
Groove
Rib
5
Upper Post
Peg
5
6
Large Square Opening
Base
6
• If the lever comes off, simply re-attach it.
6
• Insert the peg on one side of the lever into the hole in
the collar.
• Snap the other peg in the lever into the other hole in
the collar.
Base
Groove
Assembly is now complete.
IMPORTANT! Assembly of the lower post is a
permanent assembly.
Please refer to assembly step 2 to fill the base with
water or approximately 50 lbs. of sand (water and sand
not included) to keep this product stationary.
• Position the base as shown.
• Lean the rim against a wall for support.
• Position the upper post so that the straight end is
down and the curved end is up and facing away from
the base.
• Locate the pegs on each side of the rim and the
grooves on the backboard.
• Position the backboard with the Fisher-Price® logo
facing up.
• Place your foot on the base to hold it steady and slide
the backboard onto the upper post at an angle, as far
as it will go.
• Align the rib on the bottom of the lower post with the
groove in the opening in the base.
Hint: For easier assembly, apply liquid soap or rub a
candle or bar soap around the bottom of the upper post
(especially on the corners) and the inside of the large
square opening. If assembling inside, place a tarp
under the base to protect the floor surface.
Hint: For easier assembly, apply a small amount of
liquid soap around the bottom of the post. If assem-
bling inside, place a tarp under the base to protect
the floor surface.
Note: There should be no gap between the upper post
and the backboard.
• Insert the lower post into the opening and push down,
using a circular motion, until it snaps into place.
• Insert the upper post into the large square opening in
the base and, using a circular motion, push it all the
way down.
• Move the assembly away from the wall.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Rim Height
Care
• To clean, use a mild soap and water solution and
clean cloth. Rinse clean with warm water to remove
soap residue.
IMPORTANT! Rim height should only be adjusted by an adult. Also, make sure children
are not standing below the rim when adjusting the rim height.
• Be sure to drain water from the base before
extended storage. If water freezes in the base, it
could cause damage.
1
3
Backboard
4
5
4
Slots
• This toy includes an inflatable ball. If the ball becomes
soft, inflate it with a standard, hand-operated air pump
with a standard air needle.
• The ball will contain the correct amount of air when its
circumference measures 21 to 22 inches. Measure the
circumference of the ball with a tape measure or with
a piece of string cut 21 to 22 inches long. Do not over-
inflate the ball.
5
6
Upper Post
Lower Post
6
Lever
Upper Post
Base
• As assembled, the rim height is three feet.
• To raise the rim height to four, five or six feet, place
your foot on the base and pull up on the backboard
with both hands to remove the upper post from
the base. You may need to rock the upper post to
loosen it from the base.
• To lower the rim height: while holding the upper
post, push the lever on the lower post down. Lower the
upper post and push the lever into the slot at
4' or 5'.
• To raise the rim height: simply lift the upper post and
push the lever into the slot at 5' or 6'.
IMPORTANT! Since this may require a lot of force,
make sure you are not standing with your face or
chest above the backboard.
2
4
5
Slots
Upper Post
6
Lever
Lower Post
Base
• Pull the lever on the lower post down.
• Insert the upper post into the lower post with the net
positioned over the wheels on the base.
• Push the lever into one of the slots on the side of the
upper post at the desired height.
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|