X3844
IMPORTANT! KEEP FOR FUTURE REFERENCE.
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad.
Toy Bar
Head Support
Seat Back Tube
Pad
2 Retainers
Footrest
2 Toys
Left Base Wire
Right Base Wire
Base Tube
2 Feet
M5 x 20 mm Screw – 2
#8 x 2,2 cm Screw – 2
Note: Screws shown actual size. Tighten or loosen all screws
with a Phillips screwdriver. Do not over-tighten the screws.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Mattel for
replacement parts and instructions if needed. Never substitute parts.
Footrest
Base Tube
Base Wires
Left Base Wire
Right Base Wire
1
4
• Place the base tube on a flat surface.
• Position the left and right base wires as shown.
• Fit the left base wire and right base wire into the base tube.
• Position the footrest so that the soothing unit is upright.
• Fit the footrest onto the ends of the base wires.
Seat Back Tube
Non-skid Surface
2
• Position the feet so the non-skid surface is down.
• Fit the feet on the base tube, as shown.
5
• Fit the seat back tube onto the ends of the base wire.
• Push the seat back tube to be sure it is completely on the
base wires.
3
• Insert an M5 x 20 mm screw through each foot and tighten.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pad Lower Pocket
8
Retainers
• Fit the lower pocket on the back of the pad onto the footrest.
6
Toy Bar Retainer
• Fit a retainer to the inside of each end of the seat back tube.
• Insert #8 x 2,2 cm screw into the outside hole in the ends of the
seat back tube and tighten.
• Pull the seat back tube up to be sure it is secure. If you can
remove either end of the seat back tube, you have not assembled
the retainers correctly. Remove the screws, re-read and repeat.
Assembly steps 5 and 6.
Soothing Unit
9
• Fit the toy bar retainer through the side opening in the pad.
• Fit the edges of the soothing unit through the large opening in the
front of the pad.
Pad Seat Back Pocket
Head Support
7
• Position the pad above the frame.
• Fit the upper pocket on the back of the pad onto the seat back tube.
10
• Press the head support strap to the fastener on the back of the pad.
Hint: You can move the head support up or down for your
baby’s comfort.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Battery Installation
Hint: We recommend using alkaline batteries for longer battery life.
Toy Bar
1,5V
“D” (LR20)
+
–
Toy Bar Retainer
1,5V
“AAA” (LR03)
• Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities.
Latch
11
B
• Insert and “snap” the toy bar into the toy bar retainer.
• Press the latch the end of the toy bar to the tab on the socket.
Hint: The toy bar is removable. Pull the end of the latch and lift the
toy bar.
A
A
1
• Pull to remove the pad from around the toy bar retainer and the
Toys
A
soothing unit
.
B
• Remove the pad bottom pocket from the footrest
.
12
• Clip the removable toys to the hanging toys on the toy bar.
2
Soothing Unit
• Loosen the screw in the battery compartment door. Remove the
battery compartment door.
• Insert one “D” (LR20) alkaline battery into the battery compartment.
• Replace the battery compartment door and tighten the screw.
• Fit the toy bar retainer through the side opening in the pad.
• Pull and fit the pad seat bottom pocket around the soothing unit
and footrest.
• If this product begins to operate erratically, you may need to reset
the electronics. Slide the power switch off and then back on.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Installation
Setup and Use
WARNING
To prevent serious injury or death:
• Fall Hazard - Never use on any elevated
surface, since child’s movement may cause
product to slide or tip over. Use only on
a floor.
• Suffocation Hazard - Never use on a soft
surface (bed, sofa, cushion) since product
can tip over and cause suffocation in
soft surfaces.
3
• Never use as a carrier or lift while child is
seated. Never use toy bar to carry product.
• Always use the restraint system.
• This product is not intended to replace a cot
or bed for prolonged periods of sleep.
• Never leave child unattended.
Toy Bar
• Loosen the screw in the battery compartment door with
a Phillips screwdriver. Remove the battery compartment door.
• Insert one "AAA" (LR03) alkaline battery into the
battery compartment.
• Replace the battery compartment door and tighten the screw.
• If the toy bar begins to operate erratically, you may need to reset
the electronics. Remove the battery and reinstall.
• Do not use product once child can sit unaided.
Restraint Pad
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removeable, rechargeable batteries are used, they are only to be
charged under adult supervision.
Restraint Belts
1
Securing Your Infant
• Place your child in the seat. Position the restraint pad between
your child’s legs.
• Fasten the restraint belts to the restraint pad. Make sure you hear
a “click” on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup and Use
Soothing Unit and Toy Bar
Restraint System
PULL
2
Power Switch
• Tighten each waist belt so that the restraint system is snug against
your child. Please refer to the next section for instructions to
tighten the waist belts.
Anchored End
Anchored End
• Make sure your child is properly secured in the seat.
• Slide the power switch to:
Vibrations or
Off.
A
B
IMPORTANT! Low battery power causes this product to operate
erratically: no vibrations and the product may not turn off. Remove
and discard the battery and replace with a new “D” (LR20)
alkaline battery.
B
A
• Pull the toy for sounds.
Free End
Free End
LOOSEN
TIGHTEN
3
To tighten the restraint belts:
• Feed the anchored end of the restraint belt up through the buckle
A
to form a loop . Pull the free end of the restraint belt
.
B
To loosen the restraint belts:
• Feed the free end of the restraint belt up through the buckle to
A
form a loop . Enlarge the loop by pulling on the end of the loop
toward the buckle. Pull the anchored end of the restraint belt to
B
shorten the free end of the restraint belt
.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|