Product features and decorations may vary from picture above.
Instructions
Model Number: H4788
WARNING
IMPORTANT! KEEP FOR FUTURE REFERENCE.
Please read these instructions before assembly and use of this product.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Requires four “D” (LR20) alkaline batteries (not included) for operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact
Mattel for replacement parts and instructions if needed. Never
substitute parts.
M5 x 20 mm Screw - 2
Base Tube Holes
Left Base Wire
3
Right Base Wire
1
• Insert an M5 x 20 mm screw through each foot and tighten.
• Place the base tube on a flat surface, with the holes facing you.
• Position the left and right base wires as shown.
Footrest Wire
Liner
• Fit the left base wire and right base wire into the base tube.
Soother Unit
Soother Unit
Feet Holes
2
• Position the feet so the holes are toward you and the non-skid
surface is down.
• Fit the feet on the base tube, as shown.
4
• Place the liner on a flat surface with the soother unit facing you.
• Lift the footrest wire and rotate it toward you until it is on
the surface.
• Turn the liner over so that the soother is upright.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Groove
Retainers
Footrest Wire/
Seat Back Tube
7
•Fit the footrest wire/seat back tube into the groove in
the retainer.
Base Wires
5
• Fit the base wires into the slots in the retainers on the liner.
Push the retainers down.
#6 x 2.86 cm
Red Shoulder Screw – 2
#8 x 2.22 cm Screw – 2
Retainer Lower Hole
Footrest Wire/
Seat Back Tube
8
• Insert a #6 x 2.86 cm red shoulder screw through the seatback
tube, footrest wire and into the retainer. Tighten the screw.
Hint: You may find it easier to tip the assembly on its side to insert
and tighten the screw.
• Repeat this assembly step to secure the other end of the footrest
wire/seat back tube to the other retainer.
• Push down on the seat portion of the liner to be sure it is secure
to the retainers.
6
• Insert a #8 x 2.22 cm screw through the lower hole in each
retainer and the hole in each base wire. Tighten the screws.
• Pull up on the retainers to be sure they are secured to the left
and right base wires.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pad
Liner
9
11
• Fit the pad into the liner.
• Attach the fasteners at the top and sides of the pad.
Pad
Bottom
Pocket
Toys
10
• Pull and fit the pad seat
bottom pocket around the
soothing unit and footrest.
• Fit the restraint straps
through the slots in the pad.
12
• Fit any of the toy straps through a toy ring. Now, fasten the
toy strap.
Assembly is now complete.
Restraint Straps
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Installation
Massager Battery Compartment
Hint: We recommend using alkaline batteries
Soother Battery Compartment
for longer battery life.
1,5V x 4
LR20 (“D”)
_
+
Shown Actual Size
2
• Locate the electronic unit on the footrest wire. You will see that
there are two battery compartments. The smaller compartment
powers the soother; the larger battery compartment powers
the massager.
• First, loosen the screw in the soother battery compartment door
and remove the battery compartment door.
• Insert one “D” (LR20) alkaline battery into the battery compartment.
• Replace the battery compartment door and tighten the screw.
• Next, loosen the screws in the massager battery compartment
door and remove the battery compartment door.
• Insert three “D” (LR20) alkaline batteries into the battery compartment.
• Replace the battery compartment door and tighten the screws.
IMPORTANT! Low battery power may cause this product to operate
erratically (no sounds/vibration/massage) and the product may not
turn off. Remove and throw away all four batteries and replace
with four, new “D” (LR20) alkaline batteries.
Battery Safety Information
1
Pad Bottom Pocket
Batteries may leak fluids that can cause a chemical burn injury
or ruin your product. To avoid battery leakage:
• Remove the pad bottom pocket from the footrest.
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of batteries in a fire.
The batteries may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removable, rechargeable batteries are used, they are
only to be charged under adult supervision.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup and Use
Restraint Pad
WARNING
To prevent serious injury or death:
•It is dangerous to use this reclined
cradle on an elevated surface, since
child's movement may cause infant
seat to slide or tip over.
•Never use on a soft surface (bed, sofa,
cushion), since seat can tip over and
cause suffocation in soft surfaces.
•Always use the restraint system.
•Never leave the child unattended.
•Never use as a car seat.
1
Restraint Straps
•Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg (20 lbs).
•To prevent the massaging rollers from
contacting baby’s head, use only for a
baby weighing at least 2.3 kg (5 lbs).
Securing your Infant
• Place your child in the seat. Position the restraint pad
between your child’s legs.
• Fasten the restraint straps to the restraint pad. Make sure you
hear a “click” on both sides.
• Check to be sure the restraint system is securely attached
by pulling it away from your child. The restraint system should
remain attached.
IMPORTANT! Before each use, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use if
any parts are missing or broken. Contact Mattel for replacement
parts and instructions if needed. Never substitute parts.
Anchored End
Anchored End
Free End
Free End
LOOSEN
TIGHTEN
2
To tighten the restraint straps:
• Feed the anchored end of the restraint strap up through the
buckle to form a loop Ạ. Pull the free end of the restraint
strap ạ.
To loosen the restraint straps:
• Feed the free end of the restraint strap up through the buckle
to form a loop Ạ. Enlarge the loop by pulling on the end
of the loop toward the buckle. Pull the anchored end of the
restraint strap to shorten the free end of the restraint strap ạ.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Soother and Massage
• Make sure your child is properly secured in the seat.
Slide the vibrations
switch:
Vibrations On
Off
Note: If vibrations become faint or if there are no vibrations, remove
the battery from the small battery compartment and throw it away.
Replace the battery with a new, “D” (LR20) alkaline battery.
Slide the sound switch to choose:
Lullabies Music
New Age Music
Nature Sounds
Off
Note: Music/Sounds turn off after approximately 8 minutes. To turn
music/sound back On, slide the sound switch Off and then to the
desired On mode.
Slide the massage
switch:
Massage Switch
Reset Button
Massage On
Off
Massage unit runs for 8 minutes – massaging baby for 20 seconds, resting
for 5 seconds, massaging baby for 20 seconds, etc. To restart for another
eight minutes, press the reset button
.
Note: If sounds or massage become faint or if there are no sounds or
massage, remove the batteries from the large battery compartment and
throw them away. Replace the batteries with three, new, “D” (LR20)
alkaline batteries.
Sound Switch
Vibration Switch
Care
• The pad is machine washable. Wash it separately in cold
water on the gentle cycle. Do not use bleach.
Line dry only.
• The frame, toys and liner may be wiped clean using a
mild cleaning solution and a damp cloth. Do not use
bleach. Do not use harsh or abrasive cleaners. Rinse
clean with water to remove residue.
• First fit the restraint belts back through the slots in the pad.
• Pull the pad bottom pocket off the footrest.
• Lift the pad off the liner.
• To replace the pad, refer to Assembly steps 9 - 11.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|