Kick & Play
Bouncer
Model Number: 79636
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Tool required for assembly: Phillips screwdriver (not included).
Requires one “D” (LR20) alkaline battery (not included) in the soothing unit.
Requires three “AA” (LR6) alkaline batteries (not included) in the toy bar.
ver
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Toy Bar
Removable
Teether Rings
Seat
Back
Tube
2 Retainers
Pad
Footrest with
Soothing Unit
Right Base Wire
Base
Tube
3
#8 x /4" Screw - 2
Left Base Wire
Shown Actual Size
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Installation
Soothing Unit
• Locate the soothing unit on the footrest wire.
• Loosen the screw in the soothing unit battery compartment door with a
Phillips screwdriver. Remove the battery compartment door.
• Insert one “D” (LR20) alkaline battery, as indicated inside the battery
compartment.
• Replace the battery compartment door. Tighten the screw with a Phillips
screwdriver. Do not over-tighten.
Toy Bar
• Loosen the screw in the toy bar battery compartment door with a Phillips
screwdriver. Remove the battery compartment door.
• Insert three “AA” (LR6) alkaline batteries, as indicated inside the battery
compartment.
• Replace the battery compartment door. Tighten the screw with a Phillips
screwdriver. Do not over-tighten.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Tips
1.5V x 3
"AA" (LR6)
SHOWN ACTUAL SIZE
1.5V
"D" (LR20)
SHOWN ACTUAL SIZE
_
+
• Do not mix old and new batteries.
• Do not mix different types of batteries: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
• Remove the batteries during long periods of non-use. Always remove
exhausted batteries from the toy. Battery leakage and corrosion can
damage this product. Dispose of batteries safely.
• Do not dispose of batteries in a fire. The batteries may explode or leak.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type as recommended in the
"Battery Installation" instructions are to be used.
• If removable rechargeable batteries are used, they are only to be charged
under adult supervision.
• Rechargeable batteries are to be removed from the product before they
are charged.
• If you use a battery charger, it should be examined regularly for damage to
the cord, plug, enclosure and other parts. Do not use a damaged battery
charger until it has been properly repaired.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
CAUTION
This package contains small parts
in its unassembled state.
Adult assembly is required.
Right Base
Colored Tabs
Wire
Base
Tube
Left Base
Wire
1
Base
Wire
Base
Tube
• Place the base tube on a flat surface
as shown.
• Position the left and right base wires as
shown. Note the locations of the colored
tab on the left and right base wires.
Colored Tab
• Fit the left base wire into the base tube.
• Fit the right base wire into the base tube.
Back View
• Make sure both colored tabs on the base wires are visible through
the holes in base tube.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Soothing Unit
Footrest Buttons Up
Flex Base
Wires
Inward
Tabs
2
• Position the footrest so that the soothing unit buttons are upright.
• While flexing the base wires toward each other, hook the footrest onto the
ends of the base wires.
• Push the footrest down completely to the tabs on the base wires.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Seat Back
Tube Bends
Backward
Retainers
Base
Wire
Base
Wire
3
• Position the seat back tube so that it bends backward.
• Fit the seat back tube completely onto the base wires. Make sure the hole
in each end of the seat back tube aligns with the hole in each base wire.
• Fit a retainer (rounded side inward) to one end of the seat back tube.
• Insert a screw through the outside hole in the seat back tube and into
the retainer.
• While holding the retainer in place, tighten the screw with a Phillips screw-
driver. Do not over-tighten.
• Repeat this procedure to secure the other side of the seat back tube to the
base assembly using the remaining retainer and screw.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pull Up
4
• Pull up on the seat back tube to be sure it is secure. If you can remove
either end of the seat back tube, you have not assembled it correctly.
Remove the screws and retainers. Re-read and repeat Assembly steps
3 and 4.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pad
B
Footrest
Seat Back
Tube
5
• Unbuckle the restraint belts from the restraint
pad. Push the restraint belts back through the slots in the pad
.
• Fit the pad upper pocket onto the seat back tube
.
B
• Lift the footrest. Fit the pad lower pocket onto the footrest
Lower the footrest.
.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Restraint
Belts
56
• Fit both restraint belts back through the pad slots, as shown.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
7
• Fit the ends of the toy bar into the sockets in the footrest.
Hint: The square end of the toy bar fits into the square socket and the circular
end of the toy bar fits into the circular socket.
Assembly is now complete.
• The toy bar is removable. Simply lift up to remove.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Set-Up & Use
WARNING
To prevent serious injury and/or falls:
• Never use on any elevated surface,
since child’s movement may cause
bouncer to slide or tip over.
• Never use as a carrier or lift while child
is seated.
• Always use the restraint system.
• Never leave child unattended.
• Never use with a child able to sit
up, unassisted.
Restraint
Belt
Buckle
Restraint Pad
1
Securing Your Child
• If the toy bar is attached, remove it before placing your child in the seat.
• Place your child in the seat. Position the restraint between your child’s legs.
• Fasten both restraint belts to the buckles on each side of the restraint pad.
Make sure you hear a “click” on both sides.
• Check to be sure the restraint is securely attached by pulling it away from
your child. The restraint should remain attached.
• Attach the toy bar, if desired (see Assembly step 7).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Set-Up & Use
Anchored End
Anchored End
B
B
Free End
Free End
2
Loosen
Tighten
To tighten the belts:
• Feed the anchored end of the belt up through the buckle to form a loop
.
B
• Pull the free end of the belt
.
• Repeat this procedure to tighten the other belt.
To loosen the belts:
• Feed the free end of the belt up through the buckle to form a loop
Enlarge the loop by pulling on the end of the loop toward the buckle.
.
B
• Pull the anchored end of the belt to shorten the free end of the belt
• Repeat this procedure to loosen the other belt.
.
Please Note: After adjusting the belts to fit your child, make sure you pull on
them to be sure they are securely fastened.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Set-Up & Use
3
Calming Vibrations
• Make sure your child is properly secured in the seat.
• To turn vibrations on, slide the power switch on the soothing unit to the on
position
• To turn vibrations off, slide the power switch on the soothing unit to the off
position
.
.
IMPORTANT! If vibrations from the soothing unit become faint, or if there
are no vibrations, remove the battery from the soothing unit and dispose of
it properly. Replace the battery with a new “D” (LR20) alkaline battery.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Set-Up & Use
Mode Switch
Volume
Switch
Mode and
Volume
Switches
Footrest
Buttons
(Underneath
Pad)
4
Sounds and Lights
Baby Activated
• Slide the mode switch to for baby activated mode.
• When baby kicks a footrest button, baby is rewarded with sound effects
and chasing lights. After baby kicks the buttons several times in a row, baby
enjoys a musical tune and twinkling lights.
Parent Activated
• Slide the mode switch to for parent activated mode. Baby enjoys 10
minutes of music and a light show.
Off
• Slide the toy bar switch to to turn off sounds and lights.
• Slide the volume switch to for low volume; for high volume.
IMPORTANT! If lights become dim or sound becomes faint, remove the
batteries from the toy bar and dispose of properly. Replace the batteries
with three, new “AA” (LR6) alkaline batteries.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Set-Up & Use
Teethers
5
• The teethers are removable from the toy on the toy bar. Simply twist the
ends of each teether slightly to remove them from the center toy.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Care
The pad is machine washable. Wash the pad separately in cold water on the
gentle cycle. Do not use bleach. Tumble dry separately on low heat and
remove promptly. The frame and toy bar and teethers can be wiped clean
using a mild cleaning solution and a damp cloth. Do not immerse the soothing
unit or toy bar.
To remove the pad:
• Lift the footrest and remove the pad lower pocket
• Push the restraint belts back through the pad.
• Slide the pad upper pocket off the seat back tube.
To re-assemble the pad:
• Refer to assembly steps 5 and 6.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Statement (United States Only)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user's authority to operate
the equipment.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Information
Occasionally a consumer may experience
a problem with one of our products.
If this should happen, please call us toll-free,
rather than return this product to the store.
Usually, we can solve the problem over the telephone
or send you replacement parts.
Please call Fisher-Price® Consumer Relations,
toll-free at 1-800-432-KIDS,
8 AM - 6 PM EST Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
Or, write to:
Fisher-Price® Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
For other countries, outside the United States:
Canada: call 1-800-567-7724, or write to:
Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
Great Britain: telephone 01628 500302.
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond,
Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
79636a-0920
©2002 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in China
|