M7332
Please keep this instruction sheet for future reference,
as itcontains important information.
Adult assembly is required.
Required tools: Hammer, Phillips Screwdriver
and Scrap Block of Wood (not included).
Age: 2 - 6 years; Weight Limit: 60 lbs (27 kg).
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
CAUTION
Rear Wheel
Indented Side Up
Cap Nut
Hubcap
This product contains small parts
in an unassembled state.
Adult assembly is required.
Straight Axle
Frame
Cover
Hubcap
Assembled
Rear Wheel
Cap Nut
Assembly Tool
Rear Wheel
Indented Side Down
3
Hubcap
• Place a scrap block of wood on a flat surface.
• Turn the frame on its side with the exposed end of the
straight axle up.
Straight Axle
• Place the cap nut assembly tool under the assembled rear
wheel and onto the cap nut.
1
• Slide a rear wheel (indented side up) onto the end of the
straight axle.
• Slide a hubcap (peg side down) onto the straight axle.
• Place a cap nut on the end of the straight axle.
• Slide a hubcap (peg side up) onto the straight axle.
• Slide a rear wheel (indented side down) onto the
straight axle.
• Tap the cap nut with a hammer. Gently pull the rear
wheel up to be sure the cap nut is securely attached
to the straight axle.
• Dispose of the cap nut assembly tool properly.
Frame
• Insert one of the tabs on a cover into a slot in the hubcap.
Push to "snap" the cover in place. Repeat this procedure
to attach the other cover to the other hubcap.
• Set the frame assembly aside.
Hole
Hole
Pedal Hub
Tab
Pedal Axle
Tab
Straight Axle
BOTTOM VIEW
Slot
2
Pedal Hub
• Turn the frame upside down.
• Insert the straight axle through the holes in the rear of
the frame.
4
• Fit two pedal hubs onto the pedal axle tabs. Make sure the
tabs fit into the slot in each pedal hub.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pedal Hubs
Pedal Axle
Pedal
Front Wheel
Hole
Pedal Axle
5
Front Wheel Assembly
• While holding the pedal hubs on the pedal axle, insert the
pedal axle through the hole in the center of the front wheel.
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
7
• Place a scrap block of wood under the front wheel assembly
with the exposed end up.
• Fit a pedal on the pedal axle.
• Tap the pedal with a hammer until it is secure.
Pedal Hub
Pedal Axle
Fork Arms
Fork Cover
Pedal Hub
Groove
8
Pedal Axle
• Place the front wheel assembly between the fork arms.
Make sure the pedal axle fits into the groove at the bottom
of each fork arm.
6
• Turn the front wheel assembly over.
• Insert a pedal hub onto the top of the pedal axle and into
the hole in the center of the front wheel.
• Insert the remaining pedal hub below the pedal axle and
into the hole in the center of the front wheel.
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #8 x 3/4" (1,9 cm) screws through the fork cover
and into the fork arm. Tighten the screws with a Phillips
screwdriver. Do not over-tighten.
• Repeat this procedure to attach the other fork cover to the
other fork arm.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Seat Retainer
Handlebar
Seat
Frame Neck
Fork Post
Peg
Holes
Fork Cover
11
• Position the seat upside down.
• Fit the small pegs on the seat retainer into the holes in
the seat.
Rear of Trike
9
1
• Turn the frame upright.
• Insert the fork post up through the hole in the neck of the
frame. Make sure the fork is positioned so that the fork
covers face the rear wheels.
2
3
6
• Place the handlebar over the fork post and push it down
onto the frame. Make sure the handlebar is positioned so
that the screw hole faces the rear wheels and aligns with
the screw hole in the fork post.
Hint: You may need to rotate the handlebar to align
the holes.
• Insert the #8 x 3" (7,6 cm) screw through the hole in the
handlebar and into the fork post. Tighten the screw with a
Phillips screwdriver. Do not over-tighten.
4
5
(Label
on other side)
7
7
Cap
12
• Make sure the areas where the labels will be applied are
clean and dry. Wipe your vehicle with a clean, soft, dry
cloth to remove any dust or oils.
• For best results, avoid applying a label more than once.
• Apply the labels as shown in the illustration above.
10
• Insert and “snap” the cap into the hole in the frame.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching and Removing
the Seat
Consumer Information
IMPORTANT! It is a good practice to start training children
very young regarding the importance of helmet use. When
children are older and riding bicycles and faster vehicles,
it is important that they use a helmet each and every time
they ride. For this reason, even while riding a tricycle, it is
a good idea to familiarize your child with helmet use, so that
it becomes a habit for life. Choose a helmet that complies
with requirements of the applicable certifying agency for
bicycle helmets.
Helpful Hint: The seat can be attached to the frame in any
of three positions, depending on the size of your child. Check
your child’s fit on the trike by observing the seat to pedal
distance, as it is being ridden. If the pedals seem too far away
or too close for your child, move the seat up or down.
Seat
Tabs
Care
Seat
Retainer
• Periodically, check the plastic parts and if broken or cracked,
dispose of them properly.
• Check all fasteners regularly to be sure they are tight. If the
fasteners are not tight, tighten them as necessary.
• To clean, use a mild soap and water solution and a clean
cloth. Rinse clean with water to remove soap residue.
Slots
CONSUMER ASSISTANCE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Middle Position
Lower Position
Upper Position
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
• At an angle, insert the tabs on the seat into any of the top
three sets of slots for the lower, middle or upper position.
• Lower the seat so that the seat retainer inserts and snaps
into the slots in the frame.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
• Pull up on the seat to be sure it is secure.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Seat
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
Seat Retainer
Tab
Frame
Seat Retainer Tab
• Turn the frame on its side.
• Squeeze the seat retainer tabs toward one another and lift
the seat from the frame.
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A.
©2011 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN MExICO
M7332a-0921
Download from Www.Somanuals.com. All Manuals Search And Download.
|