BOUNCE ’N PLAY
ACTIVITY DOME
Model Number: 79534, 79545, 79546
Please save these instructions for future reference.
Tool needed for assembly: Phillips Screwdriver (not included).
Use only for a child who is unable to push up on hands and knees, pull up or sit unassisted.
Product features may vary from picture above.
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
Metal Canopy Stay
®
®
Pad
2 Covers
3 Toys
(Toys may
be different
than shown)
2 Base Wires
Base
Spring - 4
Plastic Mesh Cover Stay
13
M5 x 1 /16" Screw - 2
CAUTION
In its unassembled state, this
5
M6 x 1 /8" Screw - 8
product contains small parts.
Adult assembly is required.
M5 Lock Nut - 2
M6 Lock Nut - 8
SHOWN ACTUAL SIZE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed.
Never substitute parts.
Button Hole
Plastic Mesh
Frame
Cover Stay
3
1
Middle Hole
Middle Hole
Mesh Cover
Frame Tube
Frame Tube
• Position the ends of the frame tubes against the middle holes
in a frame.
Base
• Open the base and position it upright on a flat surface,
as shown.
• Locate the end of the base with the mesh cover. Insert the
entire plastic mesh cover stay into one of the button holes
in the mesh cover.
M6 Lock Nut
4
• Be sure to tuck the plastic mesh cover stay away from the
button hole in the mesh cover.
Frame Tube
Canopy Tunnel
2
Frame Tube
Metal
Canopy
Stay
Frame
Protruding
Side
5
M6 x 1 /8" Screw - 4
M6 Lock Nut - 4
• Insert an M6 x 15/8" screw through each frame tube and into
the frame.
• Fit an M6 lock nut (so that the protruding side is toward the
fabric) into each middle opening on the back of the frame.
• Insert the metal canopy stay through the canopy tunnel.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Metal Canopy Stay
5
7
Cover
Upper
Hole
• Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
Slot
Tab
• Repeat this procedure to attach the other ends of the frame
tubes to the frame on the other side of the base.
Protruding
Side
Frame
13
M5 x 1 /16" Screw -2
M5 Lock Nut -2
6
Lower Hole
Spring
• Position one end of the metal canopy stay against the upper
hole in a frame.
• Insert an M5 x 113/16" screw through the hole in the cover.
• Fit the end of the screw through the hole in the metal canopy
stay and into the upper hole in the frame.
• Push on the cover to insert and “snap” the tab on the cover into
Lower Hole
the slot in the frame. Make sure you hear a “snap”.
Base Wire
• Fit an M5 lock nut (so that the protruding side is toward the
fabric) into the upper hexagonal opening on the back of
the frame.
Spring - 4
• Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other end of the metal
canopy stay and the remaining cover to the frame on the other
side of the base.
Protruding Side
M6 Lock Nut - 4
5
M6 x 1 /8" Screw - 4
• Position the base wires around the base so that the ends point
upward and are against the lower holes in a frame.
• Place a spring onto an M6 x 15/8” screw.
• Insert the M6 x 15/8" screw with spring through a base wire and
into the frame.
• Fit an M6 lock nut (so that the protruding side is toward the
fabric) into each lower hexagonal opening on the back of
the frame.
• Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other ends of the base
wires to the frame on the other side of the base.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
USE
To Unfold
Toys
Canopy
Fasteners
8
1
Pad
Fastener
Sides of Base Wire
• Position the product upright on a flat surface.
• Grasp both sides of a base wire.
®
• Pull both sides of the base wire outward and then let the base
wire rotate down.
Note: If the base wire does not freely rotate down, pull the sides
of the base wire further outward.
• Fasten the pad fasteners to the base fasteners.
• Lift the canopy.
• Attach the toys to the canopy fasteners.
IMPORTANT! Assembly is now complete, but Bounce ‘n Play
Activity Dome is not ready for use. Please refer to the Use
instructions, on this page, beginning with step 2.
2
Frame
Groove
Groove
Sides of Base Wire
• Lift the product up slightly so that each side of the base wire
“snaps” into the groove in each frame. Make sure you hear
a “snap”.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
USE
Using the Mesh Cover
Zipper
3
Mesh Cover Up
5
Canopy Up
Frame
Groove
Base Wire
®
• Push down on the product to be
sure each side of the base wire is
in the correct position. The base
wire should rest in the groove in
each frame.
• Adjust the canopy and mesh cover up.
• While holding the mesh cover up, fasten the zipper closed.
Correct
To Fold for Portability
• Repeat Use steps 1 - 3 to unfold
the other base wire.
Using the Canopy
6
Canopy Up
Frame
4
Canopy
Down
Groove
Groove
Sides of Base Wire
• Grasp both sides of a base wire.
®
• While lifting the product up slightly, pull both sides of the
base wire outward to remove the base wire from the groove
in each frame.
• Adjust the canopy up or down.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
USE
CARE
The pad and toys are machine washable. Wash the pad and toys
separately in cold water on the gentle cycle. Do not use bleach.
Tumble dry separately on low heat and remove promptly. The
fabric and frame may be wiped clean using a mild cleaning
solution and a damp cloth.
Base Wire
7
• Rotate the base wire up.
• Repeat this procedure to fold the other base wire.
If you have any questions about this product:
In CANADA: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga,
Ontario L5R 3W2. Questions? 1-800-567-7724.
In GREAT BRITAIN: Mattel U.K., Ltd., Helpline: 01628 500303.
In AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,
Richmond, Victoria 3121 Australia. Consumer Advisory Service 1-800-800-812
(valid only in Australia).
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
79534F-0920
©2000 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Printed in Hong Kong
Download from Www.Somanuals.com. All Manuals Search And Download.
|