Product features and decorations may vary from picture above.
Instructions
Model Number: H5988
WARNING
IMPORTANT! PLEASE KEEP INSTRUCTIONS FOR FUTURE REFERENCE.
Please read these instructions before assembly and use of this product.
Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included).
Requires four LR20 (“D”) alkaline batteries (not included) for swing operation.
Requires four LR6 (“AA”) alkaline batteries (not included ) for toybar operation.
Only to be used by children that cannot climb out of seat.
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if
any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts.
Hubs
Leg
Housing
Button
Back Base
1
• Place a housing on a flat surface.
• Insert the button end of a leg into the hole in the housing.
• Push the leg in until it “snaps” into the housing.
• Repeat this procedure to assemble the other leg to the
other housing.
• Pull the legs to be sure they are secure in the housings.
If you can remove them, you have not assembled them
correctly. Please re-read and repeat this assembly step.
Front Curved Base
3
• Place the front curved base on a flat surface so that it curves
away from you.
• Place the back base on a flat surface, behind the front
curved base.
Leg
• Position the leg assemblies so that the hubs are facing
each other.
• Fit the ends of the legs over the ends of the front and back
bases, as shown.
Hint: You may need the help of another adult to help you balance
the assembly.
2
• Pull the other leg back until it “snaps” into place in the housing.
• Repeat this procedure to “snap” the leg in the other housing
into place.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
CORRECT
INCORRECT
HUBS FACING OUT
HUBS FACING IN
FRONT
BASE
CURVES
INWARD
FRONT
BASE
CURVES
OUT
4
• Check to be sure you have assembled the leg assemblies to the bases correctly. Please refer to the illustrations above.
• If the leg assemblies are assembled incorrectly to the bases, simply pull the legs from the bases. Please re-read and repeat
assembly step 3.
• Set the frame assembly aside.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Armrest Holes
Oval End
Seat Tube
Round End
Seat Tube
Round
5
Seat Bottom
7
• Position the seat bottom so that the back faces you and the
armrest holes are facing up.
Seat Bottom
Oval
• Locate the round end seat tube.
Hint: Look at opening in the straight end of the tube. It should be round.
• Fit the round end seat tube into the round hole in the
seat bottom.
• Locate the oval end seat tube.
Hint: Look at opening in the straight end of the tube. It should be oval.
• Fit the oval end seat tube into the oval opening in the
seat bottom.
3.8 cm Pin Screw
3.8 cm Pin Screw
8
SIDE VIEW
6
SIDE VIEW
• Align the hole in the seat tube with the hole in the armrest.
• Insert a 3.8 cm pin screw through the armrest and into the
seat tube. Tighten the screw.
• Align the hole in the seat tube with the hole in the armrest.
• Insert a 3.8 cm pin screw through the armrest and into the
seat tube. Tighten the screw.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Seat Back
Raised Slots
Seat Back Wire
Seat Bottom
9
• Fit the seat back to the seat bottom.
#8 x 1.9 cm Screw
11
• Fit the seat back wire through the raised slots on the seat back.
Rod
10
• Insert the rod into the side opening between the seat back
and seat bottom.
• Insert a #8 x 1.9 cm screw into the opening in the rod
and tighten.
12
• Fit the ends of the seat back wire into the outside holes in
the seat tubes.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Hubs
Seat Tubes
Assembly
Tool
14
• Insert the ends of the seat tubes into the holes in the hubs.
• Push the seat tubes in until you hear a “snap” (for each).
Rounded Side
• Push down on the seat to be sure the seat is secured in both
frame hubs.
Lock Nut – 2
13
• Attach a lock nut, rounded side facing out, onto one end of a
seat back wire.
#6 x 3.18 cm Screw – 2
• Tighten the lock nut by using the assembly tool. Turn the tool
clockwise to tighten the lock nut.
• Repeat this procedure to attach the other lock nut to the other
end of the seat back wire.
• Please throw the assembly tool away after completing this
assembly step.
15
• Insert a #6 x 3.18 cm screw into each frame hub and tighten.
• Again, push down on the seat to be sure the seat is secured to
both frame hubs.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Elastic Loops
Waist Belts
17
Holes
• Insert the waist belts through the slots in the pad.
• Fit the top of the pad over the seat back edge.
Elastic Loops
Tabs
16
• Place the pad onto the seat.
• Insert the pad elastic loops through the holes in the
seat bottom.
• From under the seat, fit the elastic loops onto the tabs
on the seat back.
Tabs
18
• From behind the seat, fit the pad elastic loops to the tabs on
the seat back.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Toy Bar Hubs
Slot
#8 x 1.9 cm Screw – 2
Crotch Belt
Seat Tubes
20
• Fit the toybar hubs to the seat tubes.
Hint: The toybar hubs are designed to fit to the seat tubes one way. If the
toybar hubs do not fit correctly, turn the toybar around and try again.
• Insert a #8 x 1.9 cm screw through the seat tubes and into the
toybar hubs. Tighten the screws.
Clips
Elastic Loops
19
• Fit the crotch belt through the slot in the pad.
• Fit the pad side clips around the edge of the seat bottom.
• Fit the pad elastic loops around the front edge of the
seat bottom. Attach the pad elastic loops to the tabs
underneath the seat bottom.
Tray
21
• Fit and “snap” the tray onto the seat armrests.
Assembly is now complete.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Installation
Swing
Toybar
Hint: We recommend using alkaline batteries for longer battery life.
Hint: We recommend using alkaline batteries for longer battery life.
1,5V x 4
“AA” (LR6)
1,5V x 4
“D” (LR20)
Shown Actual Size
Shown Actual Size
Battery Compartment
Battery Compartment
• Loosen the screws in the battery compartment door and
remove the battery compartment door.
• Loosen the screws in the battery compartment door and remove
the battery compartment door.
• Insert four “D” (LR20) alkaline batteries into the
battery compartment.
• Insert four “AA” (LR6) alkaline batteries into the
battery compartment.
• Replace the battery compartment door and tighten the screws.
• Replace the battery compartment door and tighten the screws.
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
Battery Safety Information
Setup and Use
Batteries may leak fluids that can cause a chemical burn
injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
WARNING
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of batteries in a fire.
The batteries may explode or leak.
To prevent serious injury or death
from falls and being strangled in
the restraint system:
• Never short-circuit the battery terminals.
• Always use the restraint system.
Never rely on the tray to restrain child.
• Never use with an active child who
may be able to climb out of the seat.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg (20 lbs).
• Never leave the child unattended.
• It is dangerous to use this product
on an elevated surface.
• Use only batteries of the same or equivalent type
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removable, rechargeable batteries are used, they are
only to be charged under adult supervision.
IMPORTANT! Before each use, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing or broken. Contact Mattel for replace-
ment parts and instructions if needed. Never substitute parts.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup and Use
Securing your Infant
Swinging
Power Indicator
Waist Belts
Power Switch
Crotch Belt
1
3
• Place your child in the seat. Position the crotch belt between
your child’s legs.
• Fasten the waist belts to the crotch belt. Make sure you
hear a “click” on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
• Make sure your child is properly secured in the seat.
• Slide the swing power switch on to any of six speed settings.
The power indicator lights.
• Give the seat a light push to begin swinging.
• Watch the bird “fly” when the seat swings!
• Be sure to slide the switch to the off position when the swing
is not in use.
Hint: As with most battery-powered swings, a heavier child will reduce
the amount of swinging motion on all settings. In most cases, the low
setting works best for a smaller child while the high setting works best
for a larger child.
Anchored End
Anchored End
Note: Low battery power may cause product movement to
slow or turn off all together. If this should happen, please
remove and discard all four batteries and replace with four,
new “D” (LR6) alkaline batteries.
Free End
Free End
TIGHTEN
LOOSEN
2
To tighten the waist belts:
• Feed the anchored end of the waist belt up through the buckle
to form a loop ꢀ. Pull the free end of the waist belt ꢁ.
To loosen the waist belts:
• Feed the free end of the waist belt up through the buckle to
form a loop ꢀ. Enlarge the loop by pulling on the end of the
loop toward the buckle. Pull the anchored end of the waist belt
to shorten the free end of the waist belt ꢁ.
Download from Www.Somanuals.co1m2. All Manuals Search And Download.
Setup and Use
Adjusting the Seat
Using the Toy Bar
Volume Switch
Lights Switch
Lights Switch
Volume Switch
Seat Wire
4
UPRIGHT
SEMI-RECLINE
RECLINE
Adjust the seat angle to any of three positions: Upright,
Semi-Recline or Recline. To adjust the seat angle:
• Lift or lower the seat wire into the grooves on the seat back.
5
• Slide the lights switch to
• Slide the volume switch to
On or
high volume or
Off.
low volume.
Hint: Your baby can enjoy lights and music with or without swinging!
Download from Www.Somanuals.co1m3. All Manuals Search And Download.
Setup and Use
Parent Activated
Baby Activated
Mode Switch
Mode Switch
Mode Switch
Mode Switch
Pull
Pull
6
7
• Slide the mode switch to
Baby Activated.
• Slide the mode switch to
Parent Activated.
• When baby pulls the toys on either end, baby enjoys a fun
sound effect or short melody and twinkling lights (if lights
switch is turned on).
• Baby enjoys 10 minutes of music along with twinkling lights
(if lights switch is turned on).
• Slide the mode switch to
to turn the toybar off.
• Slide the mode switch to
to turn the toybar off.
Hint: If sounds or lights slow or dim or turn off altogether, it’s time
to replace the batteries in the toybar. Replace the batteries with four, new
“AA” (LR6) alkaline batteries.
IMPORTANT! Do not pull the center bird toy!
Hint: If sounds or lights slow or dim or turn off altogether, it’s time
to replace the batteries in the toybar. Replace the batteries with four, new
“AA” (LR6) alkaline batteries.
.
Download from Www.Somanuals.co1m4. All Manuals Search And Download.
Storage
Care
• The pad, frame and toy bar may be wiped clean using a mild
cleaning solution and a damp cloth. Do not use bleach. Do not
use harsh or abrasive cleaners. Rinse clean with water to
remove residue.
PRESS BUTTON
1
Elastic Loops
To remove the pad:
• Remove the four pad elastic loops from the seat back and
bottom tabs.
• Remove the top of the pad from the seat.
• Press the button on each housing and push the rear legs
toward the front legs. Stand the frame against a wall
for storage.
Waist and
Crotch Belts
2
Clips
• Unhook the pad clips from the sides of the seat.
• Remove the pad elastic loops from the front edge of the
seat bottom.
• Push the waist and crotch belts back through the pad slots.
• Remove the pad from the seat.
To replace the pad, refer to Assembly steps 16-19.
Download from Www.Somanuals.co1m5. All Manuals Search And Download.
Consumer Information
GREAT BRITAIN
Helpline: 01628 500302. Or write to: Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB.
AUSTRALIA
Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service
1300 135 312.
ASIA
Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China.
MALAYSIA
Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd. (993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran Tropicana Golf
Country Resort, 47410 PJ. Tel: 03-78803817, Fax: 03-78803867.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2005 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA
H5988pr-0726
Download from Www.Somanuals.com. All Manuals Search And Download.
|