Fisher Price Baby Accessories 79652 User Manual

Bounce ‘n Play  
Activity Dome  
Model Number: 79652  
Please keep this instruction sheet for future reference,  
as it contains important information.  
Tool needed for assembly: Phillips Screwdriver (not included).  
Use only for a child who is unable to push up on hands and knees,  
pull up or sit unassisted.  
i
Product features may vary from picture above.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts  
®
Metal Canopy Stay  
®
Pad  
2 Covers  
3 Toys  
(Toys may  
be different  
than shown.)  
2 Base Wires  
Base  
Spring - 4  
Plastic Mesh Cover Stay  
13  
M5 x 1 /16" Screw - 2  
CAUTION  
5
M6 x 1 /8" Screw - 8  
This product contains small parts in  
its unassembled state.  
Adult assembly is required.  
M5 Lock Nut - 2  
M6 Lock Nut - 8  
ALL SHOWN ACTUAL SIZE  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges.  
DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed.  
Never substitute parts.  
Frame  
Button Hole  
Middle Hole  
Middle Hole  
Plastic Mesh  
Cover Stay  
Mesh Cover  
3
Frame Tubes  
• Position the ends of the frame tubes against the middle  
holes in a frame.  
1
Base  
Rounded  
Side  
• Open the base and position it upright on a flat surface,  
as shown.  
• Locate the end of the base with the mesh cover. Insert the  
entire plastic mesh cover stay into one of the button holes  
in the mesh cover.  
5
M6 x 1 /8" Screw - 4  
M6 Lock Nut - 4  
• Be sure to tuck the plastic mesh cover stay away from the  
button hole in the mesh cover.  
Frame  
M6 Lock Nut  
Frame Tube  
Canopy Tunnel  
Frame Tube  
Metal  
Canopy  
Stay  
4
Push Base Up  
5
• Insert an M6 x 1 /8" screw through each frame tube and into  
the frame.  
• Fit an M6 lock nut (with the rounded side toward the fabric)  
into each middle, hexagonal opening on the back of the  
frame.  
2
• Insert the metal canopy stay through the canopy tunnel.  
Hint: You may find it easier to access the hexagonal opening  
on the back of the frame if you push the base up, so that the  
fabric is out of the way.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Frame  
5
• Tighten the screws with a Phillips screwdriver. Do not  
over-tighten.  
• Repeat assembly steps 3 - 5 to attach the other ends of the  
frame tubes to the frame on the other side of the base.  
7
Rounded Side  
M6 Lock Nut - 4  
• Fit an M6 lock nut (with the  
rounded side toward the  
fabric) into each lower, hexag-  
onal opening on the back  
of the frame.  
5
M6 x 1 /8" Screw - 4  
Spring - 4  
• Tighten the screws with a Phillips screwdriver. Do not  
over-tighten.  
• Repeat this procedure to attach the other ends of the  
base wires to the frame on the other side of the base.  
Frame  
Lower Hole  
Base  
Wire  
Spring  
6
Base Wire  
• Position the base wires around the base so that the ends  
point upward and are against the lower holes in a frame.  
5
• Place a spring onto an M6 x 1 /8" screw.  
5
• Insert the M6 x 1 /8" screw with spring through a base wire  
and into the frame.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Toys  
Canopy  
Fasteners  
Rounded  
Side  
13  
M5 x 1 /16" Screw -2  
M5 Lock Nut -2  
Pad  
Fastener  
Metal Canopy Stay  
Cover  
®
Upper  
Hole  
9
• Fasten the pad fasteners to the base fasteners.  
• Lift the canopy.  
• Attach the toys to the canopy fasteners.  
8
Slot  
Tab  
IMPORTANT! Assembly is now complete, but Bounce ‘n Play  
Activity Dome is not ready for use. Please refer to the Use  
instructions, on this page, beginning with step 2.  
• Position one end of the metal canopy stay against the  
upper hole in a frame.  
13  
• Insert an M5 x 1 /16" screw through the hole in the cover.  
• Fit the end of the screw through the hole in the metal  
canopy stay and into the upper hole in the frame.  
• Push on the cover to insert and “snap” the tab on the cover  
into the slot in the frame. Make sure you hear a “snap”.  
• Fit an M5 lock nut (with the rounded side toward the  
fabric) into the upper hexagonal opening on the back  
of the frame.  
• Tighten the screw with a Phillips screwdriver. Do not  
over-tighten.  
• Repeat this procedure to attach the other end of the metal  
canopy stay and the remaining cover to the frame on the  
other side of the base.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Use  
To Unfold  
PUSH  
PUSH  
Frame  
Groove  
Base Wire  
1
3
Sides of Base Wire  
• Position the product upright on a flat surface.  
• Grasp both sides of a base wire.  
• Pull both sides of the base wire outward and then let the  
base wire rotate down.  
Note: If the base wire does not freely rotate down, pull the  
sides of the base wire further outward.  
• Push down on the product to be  
sure each side of the base wire is  
in the correct position. The base  
wire should rest in the groove in  
each frame.  
CORRECT  
• Repeat Use steps 1- 3 to unfold  
the other base wire.  
Using the Canopy  
Canopy Up  
Frame  
Canopy  
Down  
Groove  
Groove  
2
Sides of Base Wire  
• Lift the product up slightly so that each side of the base  
wire “snaps” into the groove in each frame. Make sure you  
hear a “snap.  
®
4
• Adjust the canopy up or down.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Use  
Use  
Using the Mesh Cover  
Base Wire  
Zipper  
Mesh Cover Up  
Canopy Up  
7
®
5
• Rotate the base wire up.  
• Repeat this procedure to fold the other base wire.  
• Adjust the canopy and mesh cover up.  
• While holding the mesh cover up, fasten the zipper closed.  
Care  
To Fold for Portability  
The pad and toys are machine washable. Wash the pad and  
toys separately in cold water on the gentle cycle. Do not use  
bleach. Tumble dry separately on low heat and remove  
promptly. The fabric and frame may be wiped clean using  
a mild cleaning solution and a damp cloth.  
Frame  
Groove  
Groove  
For other countries, outside the United States:  
Canada: call 1-800-567-7724, or write to:  
6
Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.  
Great Britain: telephone 01628 500303.  
Sides of Base Wire  
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,  
Richmond, Victoria 3121 Australia.  
• Grasp both sides of a base wire.  
Consumer Advisory Service 1300 135 312.  
• While lifting the product up slightly, pull both sides of the  
base wire outward to remove the base wire from the groove  
in each frame.  
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.  
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.  
Printed in China  
©2001 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.  
79652pr-0920  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Dyson Camera Accessories DC44 User Manual
Extron electronic Stereo Receiver MTP 15HD User Manual
Fishman Water Dispenser LDS9000 User Manual
Flymo Lawn Mower 5119627 03 User Manual
Fortinet Portable Speaker 05DS525 User Manual
Frigidaire Washer Dryer FARE4044MW User Manual
Garland Range X60 6R24RS User Manual
GE Clothes Dryer DBB5000 User Manual
Gemini DJ Equipment 2400 User Manual
Generac Portable Generator 1276 1 User Manual