XP ARTIST SERIES
LOUDSPEAKER SYSTEMS
1 1 0 X P
1 1 2 X P
1 1 5 X P
1 1 0 X P, 1 1 2 X P, 1 1 5 X P
I N S T R U C T I O N M A N U A L
Download from Www.Somanuals.com. All Manuals Search And Download.
Acoustics and Cabinet Placement
There are several things to
consider when placing loud-
speaker cabinets. First
Other considera-
tions include
bass frequency
performance and
f e e d b a c k . . .
FIG. B
determine the horizontal
coverage requirements for
the room. When used in a
typical auditorium setting,
position the speakers as
shown in Fig. B. Ensure
adequate sound levels reach
each seat in the audience by
walking through the entire
auditorium—listen for any
Stage
XP
XP
When
a
XP
speaker is placed
near a wall, there
will
a
low-fre-
70°
70°
quency boost of
up to 3dB. The
drawback is that
close proximity to
Audience
gaps in coverage then reposition speakers as nec-
essary. Recheck sound coverage with a full audi-
ence in attendance, if possible.
a wall may also cause feedback.
To avoid feedback: Increase the distance
between speakers and the feedback source
whether it is a wall, a microphone, or a guitar. Use
cardioid–pattern microphones to help block feed-
back. Always keep microphones
The XP Series horn has a horizontal coverage
angle of 70º and a vertical coverage of 35º; bass
speakers are nearly
omnidirectional.
pointed away from speakers.
When setting up
FIG. C
your XP Series
Sound quality is often compro-
mised when a sound system is
required to be hidden from
XP
XP
enclosures as a
“single unit,” aim
the cabinets 70°
apart as shown in
FIG. C, for 140°
of horizontal cov-
erage.
70°
sight.
Remember that the
location of your loudspeaker
cabinets will affect sound qual-
ity and coverage area more than
any other factor.
S p e a k e r C a b l e s
Power and audio signal cables are a
common sources of sound system fail-
ure. Quality cables, carefully maintained,
are essential to the reliability of the entire
sound system. Long cable connections
or cables supplying multiple speaker
cabinets must be of a sufficient gauge to
transfer all of the available amplifier
power to the speakers. As a rule, thick-
er cables (lower gauge numbers) are
more efficient because they absorb less
power themselves.
Prevent power loss and the degradation of signal quality by
using the recommended cable gauges below.
Cable that suppplys one cabinet, such as the cable to the last
cabinet in a “daisy-chain”:
• Up to 50-feet requires 18-gauge cable
• Up to 100-feet requires 16-gauge cable
Cable that suppplys two cabinets, such as the cable from the
amp to the first cabinet in a “daisy-chain”:
• Up to 25-feet requires 18-gauge cable
• Up to 50-feet requires 16-gauge cable
• Up to 100-feet requires 14-gauge cable
3
Download from Www.Somanuals.com. All Manuals Search And Download.
XP Series Specifications
MODEL:
110XP
112XP
115XP
PART NUMBER:
071-1100-400
071-1200-400
071-1500-400
MAXIMUM OUTPUT:
(at 1 Meter)
117dB Continuous
123dB Peak
118dB Continuous
124dB Peak
120 dB Continuous
126dB Peak
CABINET:
5/8" (1.6 cm)
Particle Board
5/8" (1.6 cm)
Particle Board
5/8" (1.6 cm)
Particle Board
CONNECTIONS:
(2) 1/4" Phone Jacks
(2) 1/4" Phone Jacks
(2) 1/4" Phone Jacks
DRIVER:
Low Frequency:
10" (25.4 cm) woofer
2" (5.1 cm) voice coil
12" (30.5 cm) woofer
2" (5.1 cm) voice coil
15" (38.1 cm) woofer
2.5" (6.4 cm) voice coil
High Frequency:
Dual Piezoelectric
Dual Piezoelectric
Dual Piezoelectric
Compression Drivers
1 1/2" (3.8 cm) diaphragms
Compression Drivers
1 1/2" (3.8 cm) diaphragms
Compression Drivers
1 1/2" (3.8 cm) diaphragms
FREQUENCY RESPONSE:
65 Hz to 20kHz
97 dB
60 Hz to 20kHz
98 dB
60 Hz to 20kHz
98 dB
SENSITIVITY:
1W/1m:
POWER HANDLING:
100W (RS-426A)
200W (Program)
400W (Peak)
100W (RS-426A)
200W (Program)
400W (Peak)
150W (RS-426A)
300W (Program)
600W (Peak)
IMPEDANCE:
DIMENSIONS:
8Ω
8Ω
8Ω
Height
20.3" (51.6 cm)
14.6" (37.1 cm)
6.4" (16.3 cm)
15.6" (39.6 cm)
21.3" (54.1 cm)
18" (45.7 cm)
6.4" (16.3 cm)
18.4" (46.7 cm)
23.9"(60.7 cm)
21" (53.3 cm)
8.4" (21.3 cm)
19.6" (49.8 cm)
Width (front)
Width (rear)
Depth
WEIGHT:
37 lbs. (16.8 kg)
50 lbs. (22.7 kg)
58 lbs. (26.4 kg)
A PRODUCT OF:
FENDER MUSICAL INSTRUMENTS CORP.
CORONA, CA USA
Fender® is registered trademark of FMIC
Tolex® is a registered trademark of GenCorp, Inc.
P/N 057245 REV A
Download from Www.Somanuals.com. All Manuals Search And Download.
|