FMI Indoor Fireplace FVTR18 User Manual

NATURAL GAS LOG

VENTED DECORATIVE APPLIANCES

OWNER’S OPERATION AND INSTALLATION MANUAL

TESTED AND

LISTED BY

Models FVTR18

and FVTR24

RGA 2-72

APPROVED

Std RADCO Listing No. 1292

WARNING: Improper installa-

tion,adjustment,alteration,ser-

vice,ormaintenancecancause

WARNING:Iftheinformationinthismanualisnot

followed exactly, a fire or explosion may result

causing property damage, personal injury, or

injury or property damage. Re-

fer to this manual for correct

installation and operational

procedures. For assistance or

additional information consult

a qualified installer, service

agency, or the gas supplier.

loss of life.

— Donotstoreorusegasolineorotherflammable

vapors and liquids in the vicinity of this or any

other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Donottouchanyelectricalswitch;donotuse

any phone in your building.

WARNING: This appliance is

for installation only in a solid-

fuelburningmasonryorUL127

factory-built fireplace, con-

structed of noncombustible

material, and connected to a

working flue. (See page 7 for

minimum flue opening.)

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the fire department.

— Installationandservicemustbeperformedby

a qualified installer, service agency, or the

gas supplier.

WARNING: This is a gas-fired appliance. It uses air (oxygen) from the room in which

it is installed. Provisions for adequate combustion and ventilation air must be

provided. RefertoAirforCombustionandVentilationsectiononpage4ofthismanual.

This appliance may be installed in an aftermarket* manufactured (mobile) home,

where not prohibited by state or local codes.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

Save this manual for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

PRODUCT

OPTIONAL

PRODUCT

FEATURES

ON/OFF SAFETY VALVE/

PILOT KIT AND PROPANE/LP

CONVERSION

IDENTIFICATION

Rear Burner

Grate

An optional valve/safety pilot kit with a

piezo ignitor is available for this appliance.

This system requires no matches, batteries,

or other sources to light. You must use this

optional system for LP conversion. See Ac-

cessories, page 17.

REMOTE CONTROL READY

(MILLIVOLT) SAFETY VALVE/

PILOT KIT

Burner

Pan

An optional millivolt valve/safety pilot kit

with a piezo ignitor is available for this

appliance.Thissystemrequiresnomatches,

batteries, or other sources to light. This

systemmaybeconnectedtoawallswitchor

hand-held wireless remote control. See Ac-

Front

Burner

cessories, page 17.

Valve

Cover

Figure 1 - Product Identification

REMOTE CONTROL

ACCESSORIES

Serial Number ________________________________________

There is an optional hand-held ON/OFF

remote control that can be purchased sepa-

rately for this log set. You must use the

millivolt valve/safety pilot kit to use remote

accessories with this appliance. See Acces-

sories, page 17.

LOCAL CODES

UNPACKING

Install and use log set with care. Follow all

localcodes.Intheabsenceoflocalcodes,use

the latest edition of The National Fuel Gas

Code, ANS Z223.1, also known as NFPA

54*.

CAUTION: Do not remove the

metal data plates from the burner

pan. The data plates contain im-

portant product information.

LOG SETS

Model FTLCR18 log set is for use with

ModelFVTR18burnerset.ModelFTLCR24

logsetisforusewithModelFVTR24burner

set. Use these log sets only with their corre-

sponding burners.

*Available from:

1. Remove logs, hearth kit, pan materi-

als, and hardware from carton.

American National Standards Institute, Inc.

1430 Broadway

2. Remove all protective packaging ap-

plied to logs and base for shipment.

New York, NY 10018

3. Check all items for any shipping dam-

age. If damaged, promptly inform

dealer where you bought the product.

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

VENTED NATURAL GAS LOGS

Confined and Unconfined Space

PROVIDING ADEQUATE

VENTILATION

AIR FOR

The National Fuel Gas Code, ANS Z223.1

defines a confined space as a space whose

volume is less than 50 cubic feet per 1,000

Btu per hour (4.8 m³per kw) of the aggre-

gate input rating of all appliances installed

in that space and an unconfined space as a

space whose volume is not less than 50

cubic feet per 1,000 Btu per hour (4.8 m³per

kw) of the aggregate input rating of all

appliances installed in that space. Rooms

communicating directly with the space in

whichtheappliancesareinstalled*,through

openings not furnished with doors, are con-

sidered a part of the unconfined space.

COMBUSTION AND

The following are excerpts from National

Fuel Gas Code, NFPA 54/ANS Z223.1, Sec-

tion5.3, AirforCombustionandVentilation.

VENTILATION

WARNING: This appliance

shall not be installed in a con-

fined space or unusually tight

construction unless provisions

are provided for adequate com-

bustion and ventilation air. Read

the following instructions to in-

sure proper fresh air for this and

other fuel-burning appliances in

your home.

All spaces in homes fall into one of the three

following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 4 through 6 will

help you classify your space and provide

adequate ventilation.

This log set shall not be installed in a con-

fined space or unusually tight construction

unless provisions are provided for adequate

combustion and ventilation air.

Unusually Tight Construction

Today’s homes are built more energy effi-

cient than ever. New materials, increased The air that leaks around doors and win-

insulation, and new construction methods dows may provide enough fresh air for

helpreduceheatlossinhomes.Homeowners combustion and ventilation. However, in

weather strip and caulk around windows and buildings of unusually tight construction,

doorstokeepthecoldairoutandthewarmair you must provide additional fresh air.

in. During heating months, home owners

Unusually tight construction is de-

want their homes as airtight as possible.

fined as construction where:

* Adjoining rooms are communicating only

iftherearedoorlesspassagewaysorventila-

tion grills between them.

While it is good to make your home energy

efficient, your home needs to breathe. Fresh

air must enter your home. All fuel-burning

appliances need fresh air for proper com-

bustion and ventilation.

a. walls and ceilings exposed to the

outside atmosphere have a con-

tinuous water vapor retarder with

a rating of one perm (6x10^-11kg

per pa-sec-m²) or less with open-

ings gasketed or sealed and

Exhaustfans, fireplaces, clothesdryers, and

fuel burning appliances draw air from the

house to operate. You must provide ad-

equate fresh air for these appliances. This

will insure proper venting of vented fuel-

burning appliances.

b. weather stripping has been

added on openable windows and

doors and

c. caulking or sealants are applied

to areas such as joints around

window and door frames, be-

tween sole plates and floors, be-

tween wall-ceiling joints, be-

tween wall panels, at penetra-

tions for plumbing, electrical, and

gas lines, and at other openings.

If your home meets all of the three

criteria above, you must provide ad-

ditional fresh air. See Ventilation Air

From Outdoors, page 6.

If your home does not meet all of the

three criteria above, proceed to De-

terminingFresh-AirFlowForLogSet

Location, page 5.

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

AIR FOR

COMBUSTION AND

VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR APPLIANCE LOCATION

Determining if You Have a Confined or Unconfined Space

Use this work sheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install appliance plus any adjoining rooms with doorless passageways or ventilation grills

between the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height = _________________cu. ft. (volume of space)

Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of

the space.

2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.

_____________ (volume of space) ÷ 50 cu. ft. = (maximum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Gas fireplace logs

Gas water heater*

Gas furnace

Vented gas heater

Vent-free heater

_____________ Btu/Hr

Example:

Gas water heater

Gas fireplace logs + 55,000 Btu/Hr

Total 95,000 Btu/Hr

40,000 Btu/Hr

Other gas appliances* + _____________ Btu/Hr

Total = _____________ Btu/Hr

* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_____________ Btu/Hr (maximum the space can support)

_____________ Btu/Hr (actual amount of Btu/Hr used)

Example: 51,200 Btu/Hr (maximum the space can support)

95,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support.

You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin-

ing room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.

B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no

additional fresh air ventilation.

WARNING: If the area in which the appliance may be operated is smaller than that defined as an unconfined

spaceorifthebuildingisofunusuallytightconstruction, provideadequatecombustionandventilationairbyone

of the methods described in the National Fuel Gas Code, ANS Z223.1, Section 5.3 or applicable local codes.

Continued

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

VENTED NATURAL GAS LOGS

AIR FOR

12"

COMBUSTION AND

VENTILATION

Ventilation

Continued

Ventilation Grills

Into Adjoining Room,

Option 2

Grills

Into Adjoining

Room,

VENTILATION AIR

Remove

Door into

Adjoining

Room,

Option

Ventilation Air From Inside

Building

Option 1

Thisfreshairwouldcomefromanadjoining

unconfined space. When ventilating to an

adjoining unconfined space, you must pro-

vide two permanent openings: one within

12" of the ceiling and one within 12" of the

floor on the wall connecting the two spaces

(see options 1 and 2, Figure 2). You can also

remove door into adjoining room (see op-

tion 3, Figure 2). Follow the National Fuel

Gas Code, NFPA 54/ANS Z223.1, Section

5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

12"

Figure 2 - Ventilation Air from Inside Building

WARNING: Rework work-

sheet, adding the space of the

adjoining unconfined space. The

combined spaces must have

enough fresh air to supply all

appliances in both spaces.

Ventilated

Attic

Outlet

Air

Outlet

Air

To Attic

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two per-

manent openings: one within 12" of the

ceiling and one within 12" of the floor.

Connect these items directly to the outdoors

orspacesopentotheoutdoors.Thesespaces

include attics and crawl spaces. Follow the

National Fuel Gas Code, NFPA 54/ANS

Z223.1,Section5.3,AirforCombustionand

Ventilation for required size of ventilation

grills or ducts.

Crawl

Space

Inlet

Air

Ventilated

Crawl Space

Inlet Air

Figure 3 - Ventilation Air from Outdoors

IMPORTANT: Do not provide openings for

inlet or outlet air into attic if attic has a

thermostat-controlledpowervent.Heatedair

enteringtheatticwillactivatethepowervent.

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

Btu Input

Natural Gas

Btu Input

Propane Gas

Minimum

Vent Opening

INSTALLATION

MODEL

FVTR18

FVTR24

DESCRIPTION

18" Triple Burner

24" Triple Burner

60,000

70,000

50,000

60,000

8" dia.

CAUTION: Do not remove

the metal data plates attached

totheburnerpan. Thedataplates

contain important warranty in-

formation.

MINIMUM FIREBOX SIZES

LOG FRONT BACK

SIZE WIDTH* WIDTH** DEPTH HEIGHT

WARNING: Before installing

in a solid fuel burning fireplace,

thechimneyflueandfireboxmust

be cleaned of soot, creosote,

ashes, andloosepaintbyaquali-

fied chimney cleaner. Creosote

will ignite if highly heated. A dirty

chimney flue may create and dis-

tribute soot within the house. In-

spect chimney flue for damage.

18"

24"

28"

29 ³/4"

16"

17"

14"

15 ¹/2"

18"

*Add 2" if safety valve/pilot is used

**At depth indicated

FUEL INLET PRESSURE

SPECIFICATIONS ("W.C.)

BURNER ORIFICE

NATURAL PROPANE/LP

SIZE FRONT REAR FRONT REAR

LOG

Min.

5.5

Max.

10.5

18"

24"

.046 4x.064 .036 4x.043

.064 4x.064 .036 4x.0465

NOTICE:Installation,service,and

repair of this appliance must be

performedbyaqualifiedinstaller,

service agency, company or gas

supplier experienced with this

type of gas appliance. Only fac-

toryauthorizedcomponentslisted

intheseinstructionsmaybeused

in accordance with the

manufacturer’s instructions and

all codes and requirements of the

authorityhavingjurisdiction. Any

modifications to this kit, or use of

unauthorized components or ac-

cessory items will void the

manufacturer’swarranty,andmay

result in a hazardous condition.

Figure 4 - Technical Information Charts

CHECK GAS TYPE

VENTING SPECIFICATIONS

FOR INSTALLATION

Useonlynaturalgas. Ifyourgassupplyisnot

natural gas, you must install ON/OFF Safety

Valve/Pilot Kit (see Accessories, page 17).

Call dealer where you bought log set.

Thefireplacechimneyflueandventmustbe

drafting properly. To check the vent for

proper drafting: Light a tightly rolled news-

paper on one end and place it at the inside

front edge of the fireplace. Observe the

smoke and be sure the vent is properly

drawing it up the chimney. If the smoke

spillsoutintotheroom,extinguishtheflame

and remove any obstruction until proper

venting is achieved.

If the fireplace does not have a gas supply

shut-off valve, one must be installed.

The chimney flue must remain open a mini-

mum of 3" at all times during the operation

of this log set.

FLUE OPENING

SPECIFICATIONS

Note: This vented appliance must be in-

stalled only in a solid-fuel burning fireplace

with a working flue and constructed of non-

combustible material.

The charts in Figure 4 indicate technical

information regarding the installation of

your gas log set. Please make sure that all of

the specifications shown are applicable be-

fore installation is attempted.

The fireplace must include a working flue

andventingsystemwiththeminimumopen-

ings shown in the Figure 4.

Continued

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

VENTED NATURAL GAS LOGS

We recommend that you install a sediment

trap in supply line as shown in Figure 6.

Locate sediment trap where it is within

reach for cleaning. Install in piping system

betweenfuelsupplyandheater.Locatesedi-

ment trap where trapped matter is not likely

to freeze. A sediment trap traps moisture

and contaminants. This keeps them from

going into log set controls. If sediment trap

is not installed or is installed wrong, log set

may not run properly.

INSTALLATION

CAUTION: Use only new,

Continued

black iron or steel pipe. Inter-

nally-tinned copper tubing may

be used in certain areas. Check

yourlocalcodes. Usepipeof1/2"

diameter or greater to allow

proper gas volume to log set. If

pipe is too small, undue loss of

pressure will occur.

INSTALLING DAMPER

CLAMP

Secure the damper stop clamp provided to

the leading edge of the damper as shown in

Figure5. Ifforanyreasonthisclampdoesn't

work on your fireplace, another suitable

clamp or permanent stop must be installed,

orthedamperblademustbecutorremoved.

Installation must include an equipment

shutoff valve, union, and plugged 1/8" NPT

tap. Locate NPT tap within reach for test

gauge hook up. NPT tap must be upstream

from log set (see Figure 6).

Damper Clamp

CHECKING GAS

CONNECTIONS

IMPORTANT: Install equipment shutoff

valve in an accessible location. The equip-

ment shutoff valve is for turning on or

shutting off the gas to the appliance.

WARNING: Test all gas pip-

ing and connections for leaks

after installing or servicing. Cor-

rect all leaks at once.

Damper

Apply pipe joint sealant lightly to male

threads. This will prevent excess sealant

from going into pipe. Excess sealant in pipe

could result in a clogged burner injector.

WARNING: Never use an

open flame to check for a leak.

Apply a mixture of liquid soap

and water to all joints. Bubbles

forming show a leak. Correct all

leaks at once.

Manufactured

Fireplace

Masonry Fireplace

CAUTION:Usepipejointseal-

ant that is resistant to liquid pe-

troleum (LP) gas.

Damper

Clamp

Pressure Testing Gas Supply

Piping System

Approved Flexible Gas Hose

(if allowed by local codes)

Damper

Test Pressures In Excess Of 1/2 PSIG

(3.5 kPa)

CSA Design-Certified

Equipment Shutoff Valve

With 1/8" NPT Tap*

Figure 5 - Attaching Damper Clamp

1. Disconnect appliance with its appliance

main gas valve (control valve) and equip-

ment shutoff valve from gas supply pip-

ing system. Pressures in excess of 1/2

psig will damage heater regulator.

CONNECTING TO GAS

SUPPLY

From Gas

Meter (5"

W.C.** to

10.5" W.C.

WARNING: A qualified ser-

vicepersonmustconnectlogset

to gas supply. Follow all local

codes.

2. Cap off open end of gas pipe where

equipment shutoff valve was con-

nected.

Pressure)

3. Pressurize supply piping system by either

using compressed air or opening main gas

valve located on or near gas meter.

3" Minimum

Installation Items Needed

Before installing log set, make sure you

have the items listed below.

Cap

4. Check all joints of gas supply piping

system. Apply mixture of liquid soap

and water to gas joints. Bubbles form-

ing show a leak.

Pipe Nipple Tee Joint

Sediment Trap

• piping (check local codes)

• sealant (resistant to propane/LP gas)

• equipment shutoff valve

• test gauge connection

• adjustable (crescent) wrench or pliers

• sediment trap

Figure 6 - Gas Connection

5. Correct all leaks at once.

* Purchase the optional CSA design-certi-

fied equipment shutoff valve from your

dealer. See Accessories, page 17.

** Minimum inlet pressure for purpose of

input adjustment.

6. Reconnect log set and equipment

shutoff valve to gas supply. Check re-

connected fittings for leaks.

• tee joint

• pipe wrench

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

5. Apply thread sealant to the 1/8" brass

Installation and Gas Connection

INSTALLATION

pipe nipple and thread it onto the mani-

fold block. Tighten with a 7/16" wrench.

1. Thread the gas supply fitting to the

fireplace gas supply pipe. Use thread

sealant.

Continued

6. Slip the air restrictor over the 1/8" pipe

nipple.Apply thread sealant to the male

threads and install the rear burner

nozzle onto the fitting. Tighten with a

9/16" wrench.

Test Pressures Equal To or Less Than

1/2 PSIG (3.5 kPa)

2. Place the burner pan assembly in the

center of the fireplace floor. Make sure

the front of pan faces forward.

1. Close equipment shutoff valve (see Fig-

ure 7).

3. Install the flex gas line to the gas sup-

ply fitting. Carefully shape tube to at-

tach to adapter fitting (see Figure 10).

2. Pressurize supply piping system by either

using compressed air or opening main gas

valve located on or near gas meter.

7. Place the grate assembly over the

burner pan. Install the rear burner

bracket onto the grate with the 2 black

Phillips head #10 screws provided. Do

not tighten at this time (see Figure 9).

4. Replace valve cover.

3. Check all joints from gas meter to equip-

ment shutoff valve (see Figure 7).Apply

mixture of liquid soap and water to gas

joints. Bubbles forming show a leak.

Gas

Supply

Fitting

8. Install the “U” burner from the left side

with the open end in the front (see Fig-

ure 9). Hold the rear of the burner

higher than the bracket. Slide the burner

over the air restrictor fitting. Lower the

rear of the burner into the slots on the

burner bracket. Install the burner clip

and tighten the nuts and screws.

4. Correct all leaks at once.

Equipment Shutoff

Valve

Gas Meter

9. Install 3/8" flare x 3/8" male pipe el-

bow into the inlet of the manifold block.

Install the pipe plug into the top of the

manifold block. Use thread sealant.

Flex Gas Line

Burner Pan Assembly

(Facing Front of Fireplace)

Rear Burner Nozzle

Figure 10 - Connecting Gas to Appliance

Air Restrictor

Figure 7 - Checking Gas Joints

Pipe

Nipple

HEARTH KIT ASSEMBLY

AND INSTALLATION

Kit Assembly

Front

Burner

Note:Be sure all pipe threaded connections

are tight, and have thread compound to

prevent leaks.

Inlet

Manifold

Block

Fitting

Figure 8 - Kit Assembly

1. Remove burner inlet fitting from front

burner (installed in burner pan, see Fig-

ure 8).

Burner

Grate

Bracket

2. Make sure ports on front burner are

facing the front (open side) of burner

pan. Refit if needed.

3. Using thread sealant (resistant to the

action of propane/LP gas) on larger end

of fitting, screw the burner inlet fitting

through the hole and into the front burner

(see Figure 8). Tighten using a 7/8"

wrench. If using propane/LP gas, see

Propane/LP Gas Conversions, page 10.

Burner

Clip

Pipe

Plug

Burner Pan

Pipe Elbow

Figure 9 - Installing Burner

4. Apply thread sealant compound to the

3/8" male threads of the burner inlet

fitting. Thread the manifold block (see

Figure 8) onto the burner inlet fitting.

Use the bottom hole of the block.

Continued

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

VENTED NATURAL GAS LOGS

Screw

9. Install valve cover to burner pan using

INSTALLATION

screws provided.

Ignitor

Continued

10. Install thermocouple, pilot, and ignitor

onto valve cover as shown in Figure 14.

Use the provided screws.

Thermocouple

OPTIONAL GA9003 SERIES

ON/OFF SAFETY VALVE/

PILOT KIT ASSEMBLY

11. Push the control rod extension onto the

Pilot

“D” shaped control rod through the cen-

ter hole in the cover.

For additional convenience and safety, or

12. Install the position decal and control

forpropane/LPconversion,anoptionalON/

knob making sure to align the marks

OFF safety valve/pilot kit is available. See

with the correct stop positions of the

Accessories, page 17.

Valve

Cover

gas control. Pilot position will allow the

knob to push in about 1/2". Align the

decals in the pilot position.

WARNING: You must use a

ON/OFFsafety valve/pilot kit for

propane/LP conversion.

Natural Gas Installation

1. Thread the gas control valve onto the

Close Pipe

Nipple

close pipe nipple (see Figure 11). Use

thread sealant on the male threads of

the fitting. Thread other end of the

nipple into the burner manifold block.

Hold the manifold block with a wrench

to prevent stressing the connections to

the burners. Make sure the control rod

is facing the front (see Figure 11).

Piezo Ignitor

Control

Rod

Extension

Control Knob

Burner

Pan

Figure14-InstallingCover,ControlKnob,

and Piezo Ignitor

Gas

Manifold

Block

Control

Valve

Control Rod

2. Attach the pilot gas line to the pilot out-

let of the gas control valve and tighten.

Connect the thermocouple to the rear of

the gas control valve (see Figure 12). Do

not overtighten (finger-tight plus 1/4

turn). If using propane/LP gas, see

Changing Pilot Orifice, page 11.

Figure 11 - Installing Gas Control Valve

Propane/LP Gas Conversion

Thermocouple and Line

To convert to propane/LP gas, the two main

burner orifices and pilot orifice must be

replaced.

Pilot and Line

Main Burner Orifices

3. Install the inlet fitting into the inlet

opening of the gas control valve (see

Figure 13). Use thread sealant on the

male pipe threads.

Note:Besureallpipethreadedconnections

are tight, and have thread compound to

prevent leaks. Be sure to use the correct

orifice for your unit. See chart on page 7.

Gas Control Valve

4. Thread the gas supply fitting to the fire-

place gas supply pipe (see Figure 10, page

9). Adjust to most convenient position.

1. Remove the burner inlet fitting from

the front burner manifold (installed in

burner pan). See Figure 15, page 11.

Figure 12 - Gas Control Valve with Ther-

mocouple and Pilot

Flex Gas

Line

5. Install the gas flex line to the gas supply

fitting. Carefully shape tube to attach to

adapter fitting.

2. Make sure ports on front burner mani-

fold are facing the front (open side) of

burner pan. Refit if needed.

6. Place the burner pan assembly in the

center of the fireplace floor. Make sure

the front of pan faces forward.

3. Replace front burner injector with the

provided injector. See chart on page 7

and Figure 16, page 11. Using thread

sealant (resistant to the action of pro-

pane/LP gas) on larger end of fitting,

screw the burner inlet fitting through

the hole and into the burner manifold.

Tighten using a 7/8" wrench.

7. Test for leaks following instructions

under Testing Burner for Leaks, page 11.

Inlet

Opening

8. Retighten and adjust the location of the

gas control as necessary. The gas con-

trol should be level, with the control

rod to the front.

Gas Control

Valve

Gas Inlet

Fitting

Figure 13 - Installing Inlet Fitting and Gas

Connector Tube

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

Changing Pilot Orifice

TESTING BURNER FOR

LEAKS

1. Generously apply soapy solution to all

connections.

INSTALLATION

The pilot is provided with a natural gas

orifice installed. For propane/LP gas you

Continued

4. Apply thread sealant compound to the must remove it and replace it with an pro-

3/8" male threads of the burner inlet

pane/LP orifice. The hardware kit contains

fitting. Thread the manifold block (see an propane/LP orifice with a red stripe for

Figure 15) onto the burner inlet fitting. converting the pilot.

WARNING: Never check for

gas leaks with open flame.

Use the bottom hole of the block.

1. Gently loosen and remove the pilot

2. Light the burner with the shutoff valve

no more than half open and holding a

match slightly in front of the pan (see

Lighting Instructions, page 12).

5 . Apply thread sealant to the 1/8" brass

pipe nipple and thread it into the mani-

fold block (see Figure 15). Tighten with

a 7/16" wrench.

line connection from the bracket (see

Figure 17).

2. Replace the injector (see Figure 17)

with the propane/LP pilot injector with

the red stripe.

3. Inspect all connections for bubbles, raw

gas odor, or flame from any area other

than the burner (leaks). If leaks are de-

tected, shut off the gas valve immedi-

ately. Tighten, or reassemble the loose

connection(s) using pipe joint com-

pound until burner system is leak free.

6. Slip the air restrictor over the 1/8" pipe

nipple. Apply thread sealant to the male

threads and install the rear burner injec-

tor provided with the GA9003 (see chart

on page 7) onto the fitting. Tighten with

a 9/16" wrench. Proceed with step 7,

page 9 in Hearth Kit Assembly.

3. Replace and tighten the pilot line to the

bracket.

4. Continue with step 3 under Natural

Gas Installation, page 10.

4. When the burner is tested and leak free,

observe the individual tongues of flame

on the burner. Note: The burner design

includes more ports on the outside of the

bar. Make sure that all ports are clear

and producing flame evenly across the

burner. If any ports appear blocked, clear

them by removing the burner manifold

and reaming the ports with a modified

paper clip or other suitable tool.

Rear Burner Nozzle

Pilot

Injector

Air Restrictor

Pipe

Nipple

Figure 17 - Installing Propane/LP Pilot

Orifice

Front

Burner

5. When finished testing, turn the gas

shutoff valve OFF to extinguish all

flames.

Burner Inlet

Fitting

Manifold

Block

ADDING PAN MATERIAL

Figure 15 - Kit Assembly

1. Open the bag of ash bed material (ver-

miculite) and spread it evenly across

the burner pan to the top.You may over-

flow the front and sides of the pan to

cover the entire pan and connecting

hardware.

Injector for

Natural Gas

BURNER

INLET

FITTING

2. Open the glowing embers and evenly

cover the ash bed material (vermicu-

lite) in the burner pan.

Figure 16 - Burner Inlet Fitting with

Injectors

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

VENTED NATURAL GAS LOGS

INSTALLATION

OPERATING

APPLIANCE

Continued

INSTALLING THE EMBER

BED AND LOGS (Split Oak

Sets Shown)

1. Place the ember bed (included with

burner set) over log grate as shown in

Figure 18.

FOR YOUR SAFETY

READ BEFORE

LIGHTING

WARNING: Keep flue open

when operating unit.

2. Position the back log flush against back

of ember bed as shown in Figure 19.

3. Place the middle layer of logs as shown

WARNING: If you do not fol-

low these instructions exactly, a

fireorexplosionmayresultcaus-

ing property damage, personal

injury or loss of life.

in Figure 20. Notice the grove in the

back log for placement of log to the far

right. Adequate space should be left

between logs and ember bed for flames.

Figure 20 - Installing Logs

4. Place the top layer of logs as shown in

Figure 21.

BEFORE LIGHTING smell all around

the appliance area for gas. Be sure to

smell next to the floor because some gas is

heavier than air and will settle on the

floor.

Ember Bed

Grate

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

Figure 21 - Installing Logs

• If you cannot reach your gas supplier,

call the fire department.

Figure 18 - Installing Ember Bed

LIGHTING

INSTRUCTIONS

1. STOP! Read the safety information,

above.

2. Turn the gas shutoff valve to OFF.

3. Wait five (5) minutes to clear out any

gas. If you then smell gas STOP! Fol-

low the safety information above. If

you don’t smell gas, go on to the next

step.

4. Light a match and lay it on top of the

“U” shaped burner near the edge of

the cover on the right side of the pan.

5. Slowly turn the gas shutoff valve ON

until the burner ignites. If the burner

doesn’t ignite within 10 seconds with

the match burning, turn the shutoff

valve OFF and repeat steps 1 through

4 again.

Figure 19 - Installing Back log

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

7. Keep control knob pressed in for 30

seconds after lighting pilot. After 30

OPERATING

INSTRUCTIONS FOR

GA9003

OPERATING

APPLIANCE

seconds, release control knob.

Note: If pilot goes out, repeat steps

3 through 7.

Continued

Note:OperationinstructionsforGA9103

Remote Ready Valve/Pilot Kit will be

included with the Kit.

GAS SHUTOFF

VALVE OPERATION

8. Turn control knob counterclockwise

to the ON position. Burner

should light. If burner does not light,

call a qualified service person.

1. STOP! Read the safety information,

page 12.

2. Make sure equipment shutoff valve

is fully open.

Flame Adjustment

Control Knob

Adjust the flame ON/OFF by turning the

gas shutoff valve counterclockwise

to open or clockwise

close, as necessary.

Ignitor

Pilot

3. Press in and turn control knob clock-

OFF

FROM "PILOT" POSITION

SLIGHT PUSH TO

TURN OFF

wise

to the OFF position.

Off

PULL PUSH

Shutting Off Appliance

4. Wait five (5) minutes to clear out any

gas. Then smell for gas around log set

and near floor. If you smell gas,

STOP! See Safety information, page 2

and Air For Combustion And Ventila-

tion, pages 4 through 6. If you don’t

smell gas, go to the next step.

Turn gas shutoff valve clockwise

to the OFF position.

CURING LOGS

Figure 22 - Ignitor and Control Knob

During the 2-3 hour appliance break-in

period, you may detect an odor from the

appliance as the various paints and com-

pounds used in the manufacturing of this

log set cure. This is a normal and tempo-

rary situation that is not cause for alarm.

However, you may want to provide extra

ventilation to the room during this time.

5. Turn control knob counterclockwise

to the PILOT position and

Thermo-

couple

Pilot

press in. Keep control knob pressed

in for five (5) seconds.

Note: You may be running this log

set for the first time after hooking up

to gas supply. If so, the control knob

may need to be pressed in for 30 sec-

onds. This will allow air to bleed from

the gas system.

To ensure proper curing of the logs:

• Ignite a 2" flame and maintain it for 1

hour.

Figure 23 - Thermocouple and Pilot

• If control knob does not pop up

when released, contact a qualified

service person or gas supplier for

repairs.

• Burn the logs in consecutive 1 hour pe-

riods raising the flame an additional

2" to full flame height for a total of

three hours.

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Appliance

6. With control knob pressed in, push

down and release ignitor button. This

will light pilot. The pilot is attached

to the rear of the front burner. If

needed, keep pressing ignitor button

until pilot lights.

1. Turn control knob clockwise

to the PILOT position.

2. Press in and turn control clockwise

to the OFF position.

Shutting Off Burner Only (pilot

stays lit)

Turn control knob clockwise

the PILOT position.

Note: If pilot does not stay lit, con-

tact a qualified service person or gas

supplier for repairs. Until repairs are

made, light pilot with match.

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

VENTED NATURAL GAS LOGS

TROUBLESHOOTING

WARNING: Turn off log set

Note: For additional help, visit DESA

International’stechnicalservicewebsite

at www.desatech.com.

andletcoolbeforeservicing.Only

aqualifiedservicepersonshould

service and repair log set.

Note:Alltroubleshootingitemsarelistedin

order of operation.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

Log set is smoking/sooting excessively

(Note: It is natural and unavoidable for

vented gas log sets to produce moderate

levels of carbon (soot) where flames

contact the logs. This is especially true

with propane/LP gas.)

1. Poor fuel quality

1. Contact local natural or propane/LP gas

company

2. Fireplace venting system not drafting 2. Adjust damper wide open and/or have

properly

fireplace and venting professionally

cleaned and checked

3. Excessive flame impingement or 3. Separate the logs to allow more flame

blockage

passage

4. Improper fuel/air mixture

4. Remove any foreign items from the

flame pattern and/or check for proper

orifice sizing

5. Excessive gas supply/pressure

5. Preheat flue in very cold weather

Burner is excessively noisy

1. Passage of air/gas across irregular sur- 1. Relieve any tight bends or kinks in gas

(Note:The movement and combustion of gas

will create low, unavoidable levels of noise.)

faces

supply line

Burner flame is too low or too high

1. Incorrect gas supply or pressure

1. Check for proper gas supply pressure

2. Blocked burner orifice or burner mani- 2. Free burner orifice and manifold ports

fold ports

3. Improper burner orifice size

of any burrs, paint, or other blockage

3. Verify proper burner orifice sizing (see

Figure 4, page 7)

www.desatech.com

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

TROUBLESHOOTING

Continued

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

When ignitor button is pressed, there is no 1. Ignitor electrode not connected to igni- 1. Reconnect ignitor cable

spark at pilot (GA9003 Only)

tor cable

2. Ignitor cable pinched or wet

2. Free ignitor cable if pinched by any

metal or tubing. Keep ignitor cable dry

3. Scrape away paint on bracket for better

contact with ground on piezo ignitor

4. Replace ignitor cable

3. Bad ground on piezo ignitor

4. Broken ignitor cable

5. Bad piezo ignitor

6. Ignitor electrode broken

7. Ignitor electrode positioned wrong

5. Replace piezo ignitor

6. Replace electrode

7. Reposition electrode

When ignitor button is pressed, there is 1. Gas supply turned off or equipment 1. Turn on gas supply or open equipment

sparkatpilotbutnoignition(GA9003Only)

shutoff valve closed

2. Control knob not in PILOT position

shutoff valve

2. Turn control knob to PILOT position

3. Control knob not pressed in while in 3. Press in control knob while in PILOT

PILOT position

4. Air in gas lines when installed

position

4. Continue holding down control knob. Re-

peat igniting operation until air is removed

5. Adjust pilot flame for approximately

2" blue flame

6. Clean pilot (see Cleaning and Mainte-

nance, page 17) or replace pilot assembly

7. Replace gas control

5. Pilot adjustment screw closed

6. Pilot is clogged

7. Low gas pressure

Pilot lights but flame goes out when control 1. Control knob not fully pressed in

1. Press in control knob fully

knob is released (GA9003 Only)

2. Control knob not pressed in long enough 2. After pilot lights, keep control knob

pressed in 30 seconds

3. Equipment shutoff valve not fully open 3. Fully open equipment shutoff valve

4. Pilot flame not touching thermocouple, 4. A) Contact local natural gas company

which allows thermocouple to cool,

causing pilot flame to go out. This prob-

lem could be caused by one or both of

the following:

B) Clean pilot (see Cleaning and Mainte-

nance, page 17) or replace pilot assembly

A) Low gas pressure

B) Dirty or partially clogged pilot

5. Thermocouple connection loose at con- 5. Hand tighten until snug, then tighten

trol valve

6. Thermocouple damaged

7. Control valve damaged

1/4 turn more

6. Replace thermocouple

7. Replace control valve

Burner does not light after pilot is lit 1. Burner orifice clogged

1. Clean burner orifice

2. Contact local natural or propane/LP gas

company

(GA9003 Only)

2. Inlet gas pressure is too low

3. Burner orifice diameter is too small

3. Replace burner orifice

4. Thermocouple leads disconnected or im- 4. Reconnect leads

properly connected

Delayed ignition burner (GA9003 Only)

1. Pilot flame needs adjusting

2. Wrong pilot orifice

1. Adjust pilot flame for approximately

2" blue flame

2. Replace pilot orifice set

www.desatech.com

Continued

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

VENTED NATURAL GAS LOGS

TROUBLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your

building.

• Immediatelycallyourgassupplierfromaneighbor’sphone.Followthe

gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

IMPORTANT: Operating log set where impurities in air exist may create odors. Cleaning

supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles,

etc., create fumes. These fumes may mix with combustion air and create odors. These odors

will disappear over time.

POSSIBLE CAUSE

OBSERVED PROBLEM

REMEDY

1. Metal expanding while heating or con-

tracting while cooling

Log Set produces a clicking/ticking noise

just after burner is lit or shut off

1. This is common with most log sets. If

noise is excessive, contact qualified ser-

vice person

1. Log Set burning vapors from paint, hair

spray, glues, cleaners, chemicals, new

carpet, etc. (See IMPORTANT state-

ment above)

Log Set produces unwanted odors

1. Open flue to maximum. Stop using odor

causing products while log set is running

2. Gas leak. SeeWarning statement at

top of page

2. Locate and correct all leaks (see Check-

ing Gas Connections, pages 8 and 9)

1. Gas leak. SeeWarning statement at

top of page

2. Control valve defective

Gas odor even when control knob is in OFF

position

1. Locate and correct all leaks (see Check-

ing Gas Connections, pages 8 and 9)

2. Replace control valve

1. Gas leak. SeeWarning statement at

Gas odor during combustion

2. Locate and correct all leaks (see Check-

ing Gas Connections, pages 8 and 9)

top of page

www.desatech.com

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

PINE CONES - GA9600

(Not Shown)

CLEANING AND

MAINTENANCE

ACCESSORIES

Purchase these fireplace accessories from

your local dealer. If they can not supply

theseaccessories,callDESAInternational’s

Sales Department at 1-800-888-2050 for

information. You can also write to the ad-

dress listed on the back page of this manual.

For all models. Use for additional decora-

tion only. Carton of 6 Boxes (3 pine cones

per box).

• Keep the area around the log set clean

and clear of debris.

• Occasionally, you may use a soft bristle

brush to clean logs.

ASH BED MATERIAL

(Vermiculite) - GA9700

(Not Shown)

• Once every year a qualified agency or

certified chimney sweep should exam-

ine and clean the venting system of the

fireplace.

For all models. Carton of 6.

GLOWING EMBERS - GA9900

(Not Shown)

REPLACEMENT

PARTS

For all models. Use for firebox decoration

only.

Note: Use only original replacement parts.

Thiswillprotectyourwarrantycoveragefor

parts replaced under warranty.

SILICA SAND - GA9800

(Not Shown)

EQUIPMENT SHUTOFF

VALVE GA5010

For all models. Use for firebox decoration

only. Carton of 6.

PARTS UNDER WARRANTY

For all models. Equipment shutoff valve with

1/8" NPT tap. Fits 1/2" NPT pipe.

Contact authorized dealers of this product . If

theycan’tsupplyoriginalreplacementpart(s),

call DESA International’s Technical Service

Department at 1-800-DESA LOG (1-800-

337-2564).

LAVA ROCK - GA6066

(Not Shown)

For all models. Use for firebox decoration

only.

WhencallingDESAInternational,haveready

DECORATIVE ASH BED

CONTROL COVER - DABK

(Not Shown)

•

your name

your address

modelandserialnumbersofyourfireplace

how fireplace was malfunctioning

type of gas used (propane/LP or natural

gas)

RECEIVER AND HAND-

HELD REMOTE CONTROL

KIT - GHRC Series

An attractive way to cover control knob

and piezo ignitor.

18" ORNAMENTAL GRATE

ENHANCER - GA9310

(Not Shown)

•

purchase date

For all models. Allows the gas log set to be

turned on and off by using a hand-held

remote control. Valve/Pilot Kit GA9103

must be used with this remote.

Usually, we will ask you to return the defec-

tive part to the factory.

For 18" models only. Additional decoration

for front grate.

PARTS NOT UNDER

WARRANTY

ON/OFF SAFETY VALVE/

PILOT KIT - GA9003

(Not Shown)

24" ORNAMENTAL GRATE

ENHANCER - GA9320

(Not Shown)

Contact authorized dealers of this product

or Parts Central (see page 20). If they can’t

supply original replacement part(s), call

DESA International’s Parts Department at

1-800-972-7879 for referral information.

For all models. Required for Propane/LP

installation.

For 24" models only. Additional decoration

for front grate.

REMOTE READY VALVE/

PILOT KIT - GA9103

(Not Shown)

WhencallingDESAInternational,haveready

•

model number of your fireplace

the replacement part number

For all models.

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

VENTED NATURAL GAS LOGS

ILLUSTRATED

PARTS

BREAKDOWN

FVTR18

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

This list contains replaceable parts used in your log set. When ordering parts, follow the

instructions listed under Replacement Parts on page 17 of this manual.

PARTS LIST

FVTR18

KEY PART

NO. NUMBER

DESCRIPTION

QTY.

098249-01

901752-02

102843-01

901246-01

098304-01

901762-01

901754-02

901753-02

901750-01

901064-05

901066-01

901761-01

901760-01

901751-01

901756-01

901056-01

901058-01

101628-01

901769-02

901591-08

901528-03

901619-01

901612-01

901676-04

901530-02

901759-01

ODS Nut

Rear Burner

Burner Clip

Log Grate

Screw, 10-16 x .38

Burner Bracket

Front Burner

Burner Pan

Nozzle

Natural Gas Injector

Brass Air Mixer - Natural Gas

1/8 Hex Nipple

Manifold Block

Air Restrictor

Valve Cover

Brass Elbow Flare Fitting

Brass 3/8 FLR x 1/2 FPT Adapter

Gas Line - 10" Flex

Ember Bed

Top Log VCR11/FS

Top Log CS-16/FS

Top Log FS12Y

Top Log FS17

Top Log CS-13Y/FS

Bottom Log CSB-18/FS

Manifold Plug

PARTS AVAILABLE — NOT SHOWN

901036-01

901039-08

901242-01

RADCO GEN Rating Plate

Rating Information Plate

Damper Clamp

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

VENTED NATURAL GAS LOGS

ILLUSTRATED

PARTS

BREAKDOWN

FVTR24

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

This list contains replaceable parts used in your log set. When ordering parts, follow the

instructions listed under Replacement Parts on page 17 of this manual.

PARTS LIST

FVTR24

KEY PART

NO. NUMBER

DESCRIPTION

QTY.

098249-01

901752-01

102843-01

901246-02

098304-01

901762-01

901754-01

901753-01

901750-01

901064-01

901066-01

901761-01

901760-01

901751-01

901756-01

901056-01

901058-01

101628-01

901769-01

901527-05

901528-03

901619-01

901540-03

901612-01

901532-02

901759-01

ODS Nut

Rear Burner

Burner Clip

Log Grate

Screw, 10-16 x .38

Burner Bracket

Front Burner

Burner Pan

Nozzle

Natural Gas Injector

Brass Air Mixer - Natural Gas

1/8 Hex Nipple

Manifold Block

Air Restrictor

Valve Cover

Brass Elbow Flare Fitting

Brass 3/8 FLR x 1/2 FPT Adapter

Gas Line - 10" Flex

Ember Bed

Top Log CS-12/FS

Top Log CS-16/FS

Top Log FS12Y

Top Log CS-18/CC

Top Log FS17

Bottom Log CS-24/FS

Manifold Plug

PARTS AVAILABLE — NOT SHOWN

901036-01

901038-04

901242-01

RADCO GEN Rating Plate

Rating Information Plate

Damper Clamp

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

VENTED NATURAL GAS LOGS

NOTES

_______________________________________________________________________________________________

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

NOTES

_______________________________________________________________________________________________

901846

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY INFORMATION

KEEP THIS WARRANTY

Model

Serial No.

Date Purchased

Always specify model and serial numbers when communicating with the factory.

We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written

warranty. We make no other warranty, expressed or implied.

LIMITED WARRANTY

FMI VENTED GAS LOGS

DESA International warrants this product to be free from defects on burner system for two (2) years and logs for a lifetime from the

dateoffirstpurchase, providedthattheproducthasbeenproperlyinstalled, operatedandmaintainedinaccordancewithallapplicable

instructions. To make a claim under this warranty the Bill of Sale or cancelled check must be presented.

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this log set

toproperoperatingconditionandanallowanceforlaborwhenprovidedbyaDESAAuthorizedServiceCenter. Warrantypart(s)MUST

be obtained through authorized dealers of this product and/or DESA International who will provide original factory replacement parts.

Failuretouseoriginalfactoryreplacementpartsvoidsthiswarranty. ThelogsetMUSTbeinstalledbyaqualifiedinstallerinaccordance

with all local codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become

damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost,

labor, transportation and any and all such other costs related to repairing a defective log set will be the responsibility of the owner.

TOTHEFULLEXTENTALLOWEDBYTHELAWOFTHEJURISDICTIONTHATGOVERNSTHESALEOFTHEPRODUCT;

THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURA-

TION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE TO TWO (2) YEARS ON BURNER SYSTEM AND A LIFETIME ON LOGS FROM THE DATE

OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE PRICE OF

THE PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER

INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential

damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

For information about this warranty write:

INTERNATIONAL

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

www.desatech.com

901846 01

901846-01

Rev. A

04/00

NOT A UPC

Download from Www.Somanuals.com. All Manuals Search And Download.

Electro Voice Microphone 671B User Manual
Ericsson Telephone LBI 39169 User Manual
Excalibur electronic Games 976 User Manual
Extron electronic Network Card 066 01 User Manual
Fellowes Laminator GXL 125 User Manual
Ford Automobile 2011 Escape User Manual
Furuno Radar Detector 1715 User Manual
GE Air Conditioner MG_24 User Manual
GE Dishwasher GDWT300 User Manual
Glen Dimplex Home Appliances Ltd Cooktop 60T User Manual