Extron electronic TV Mount SI 26 User Manual

User’s Guide  
V-LockWall Mount Assembly Kit  
Replacement accessory for Extron System INTEGRATOR®  
SI 26 and SI 28 Surface Mount Speakers  
68-1364-01  
Rev. A  
01 07  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Installing the V-LockAssembly Kit  
If your speakers are not already installed, follow the instructions  
outlined in the SI 26 and SI 28 User's Guide supplied with the  
speakers (or online at www.extron.com).  
If your speakers are already installed, replace the V-Lock™  
assembly by following the instructions, below.  
N
N
N
Referring to packaging information for location,  
carefully remove and check contents before installation.  
Extron recommends that the wiring installation is  
performed by a professional audio equipment installer.  
For speaker details, specifications, troubleshooting tips,  
and service access information, refer to the  
SI 26 and SI 28 User's Guide supplied with the  
speakers, or online at www.extron.com.  
Existing wall mounting application  
To replace a damaged V-Lockassembly, where already  
installed do the following:  
1.  
Remove the Extron logo from the front of the speaker to  
access the hex cap screw. Retain logo.  
2.  
3.  
Insert the hex tool and unlock the speaker.  
Disconnect the seismic cable and audio wires from the rear  
of the speakers, and carefully lift the speakers away from  
the bracket.  
4.  
Rotate the stage (V-lock groove) 90degrees to the wall  
plate (see figure 3), to access the screws in the wall plate.  
Rotate this  
section 90°...  
...and remove  
screws.  
Figure 3 — Remove the old V-Lock Assembly  
V-LockWall Mount Assembly Kit • Installation  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation, cont'd  
5.  
Carefully remove (and retain) the mounting screws,  
taking care not to damage the mounting holes in the wall.  
Remove the mount from the wall.  
6.  
Remove a new V-Lockassembly from its box, loosen the  
hex cap screw and rotate the front section approximately  
90 degrees to the mounting plate, (see figure 3). Lightly  
tighten the hex cap screw to temporarily lock it in position,  
allowing access to the mounting holes in the wall plate.  
7.  
Pass the wire through the access hole in the wall plate and  
using the existing mounting holes and screws, securely  
mount the new assembly wall plate to the wall.  
N
If the mounting holes in the wall are damaged and  
unusable, or a new location is desired, create new  
mounting holes, following the instructions in  
the SI 26 and SI 28 User's Manual.  
8.  
9.  
Loosen the hex cap screw and turn the stage back through  
90 degrees to its upright position and lock into place.  
Reattach the seismic cable to the speaker as shown.  
Anchor this end to a  
suitable secure point.  
Seismic Safety Cable  
Attach line here  
and secure.  
Figure 4 — Re-attach the seismic safety cable  
10. Mount the speakers onto the assembly, following the  
instructions in the next section.  
Mounting the speakers  
The two models of speakers (SI 26 and SI 28) have slightly  
different mounting procedures. Follow the applicable method.  
Mounting the SI 26 speaker onto the wall mount assembly  
1.  
Carefully lift the speaker above the wall mount assembly  
and gently slide the speaker box bracket down into the  
V lock groove (see figure 5) until it locks into place.  
V-LockWall Mount Assembly Kit • Installation  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
...and slide it down  
into the V-lock groove.  
Lift the speaker up to the  
wall mount assembly....  
Box  
Bracket  
Box  
Bracket  
V Lock  
Groove  
V Lock  
Groove  
Figure 5 — Slide the speaker down onto the wall  
mount assembly  
2.  
If re-installing two speakers, repeat all the installation and  
speaker mounting steps for the second speaker, then go to  
"Final adjustments" section on the following page.  
Mounting the SI 28 speaker onto the wall mount assembly  
1a. Carefully lift the speaker up as close to the bottom of the  
wall mount assembly as possible and hook the right outer  
edge of the speaker box bracket over the right inner edge  
of the V-lock groove (see figure 6).  
Holding the speaker so that the lowest part of the speaker  
is as close to the bottom of the V-lock groove as possible  
makes it easier to hook the two parts together.  
Top View  
N
Step 1a  
Box  
Bracket  
V Lock  
Groove  
Box  
Bracket  
Hook this  
side first.  
V Lock  
Groove  
Swivel and  
hook this  
V Lock  
Groove  
side second.  
Step 1b  
Box  
Bracket  
Lift the speaker to the  
wall mount assembly,  
keeping it as low as  
possible.  
Figure 6 — Hook the speaker over the edges of the  
V-lock groove on the wall mount assembly  
1b. Rotate the speaker until the speaker box bracket left edge  
hooks over the left edge of the V-lock groove (see above).  
1c. When the bracket is securely over the V-lock groove, gently  
slide the speaker down until it locks into place.  
2.  
If re-installing two speakers, repeat all the installation and  
speaker mounting steps for the second speaker, then go to  
"Final adjustments" section on the following page.  
V-LockWall Mount Assembly Kit • Installation  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation, cont’d  
Final adjustments  
1.  
When the speaker is in place, insert the audio wires into  
the back of the speaker as shown.  
Extron  
Push down on the spring terminals  
at the back of the speaker, and insert  
the wires. Release the springs to secure.  
INPUT  
Negative  
Wire  
Positive Wire  
Figure 7 — Insert audio wires into the terminals  
If the ends of the wires are damaged and need to be  
restripped, follow the instructions in the SI 26 and SI 28  
User's Guide.  
N
2.  
3.  
Turn on the audio source and any associated devices.  
Adjust the source and device settings as desired to get the  
optimum audio output for your speaker application.  
To adjust the speaker angle insert the allen hex tool into  
the locking access, loosen the hex cap screw, and adjust to  
the desired angle (see figure 8). Torque the hex cap screw  
down clockwise until snug, about 6 to 8 turns, for the  
speaker to sit securely in the desired position.  
Turn clockwise  
to tighten.  
Figure 8 — Adjust speaker and lock in place  
After locking it into place, check that the speaker  
is secure and cannot be lifted from the wall mount  
assembly. If it does lift out, continue tightening down  
the hex cap screw until it is no longer possible to lift the  
speaker from the assembly.  
N
4.  
Replace the Extron logo, pressing it firmly into place.  
N
For speaker details, specifications, troubleshooting tips,  
and service access information refer to the  
SI 26 and SI 28 User's Guide supplied with the  
speakers, or online at www.extron.com  
V-LockWall Mount Assembly Kit • Installation  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Extron’s Warranty  
Extron Electronics warrants this product against defects in materials and workmanship  
for a period of five years from the date of purchase. In the event of malfunction during  
the warranty period attributable directly to faulty workmanship and/or materials,  
Extron Electronics will, at its option, repair or replace said products or components,  
to whatever extent it shall deem necessary to restore said product to proper operating  
condition, provided that it is returned within the warranty period, with proof of  
purchase and description of malfunction to:  
USA, Canada, South America,  
and Central America:  
Extron Electronics  
Europe, Africa, and the Middle East:  
Extron Electronics, Europe  
Beeldschermweg 6C  
1001 East Ball Road  
3821 AH Amersfoort  
Anaheim, CA 92805, USA  
The Netherlands  
Asia:  
Japan:  
Extron Electronics, Asia  
135 Joo Seng Road, #04-01  
PM Industrial Bldg.  
Singapore 368363  
Extron Electronics, Japan  
Kyodo Building  
16 Ichibancho  
Chiyoda-ku, Tokyo 102-0082  
Japan  
This Limited Warranty does not apply if the fault has been caused by misuse, improper  
handling care, electrical or mechanical abuse, abnormal operating conditions or non-  
Extron authorized modification to the product.  
If it has been determined that the product is defective, please call Extron and ask for an  
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400  
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This  
will begin the repair process as quickly as possible.  
Units must be returned insured, with shipping charges prepaid. If not insured, you  
assume the risk of loss or damage during shipment. Returned units must include the  
serial number and a description of the problem, as well as the name of the person to  
contact in case there are any questions.  
Extron Electronics makes no further warranties either expressed or implied with respect  
to the product and its quality, performance, merchantability, or fitness for any particular  
use. In no event will Extron Electronics be liable for direct, indirect, or consequential  
damages resulting from any defect in this product even if Extron Electronics has been  
advised of such damage.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Extron Electronics, USA  
1230 South Lewis Street  
Anaheim, CA 92805  
800.633.9876 714.491.1500  
FAX 714.491.1517  
Extron Electronics, Europe  
Beeldschermweg 6C  
3821 AH Amersfoort, The Netherlands  
+800.3987.6673 +31.33.453.4040  
FAX +31.33.453.4050  
Extron Electronics, Asia  
135 Joo Seng Rd. #04-01  
PM Industrial Bldg., Singapore 368363  
+800.7339.8766 +65.6383.4400  
FAX +65.6383.4664  
Extron Electronics, Japan  
Kyodo Building, 16 Ichibancho  
Chiyoda-ku, Tokyo 102-0082  
Japan  
+81.3.3511.7655 FAX +81.3.3511.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Beverage Dispenser CS 330T User Manual
Eicon Networks Network Card Diva 2430 User Manual
Everpure Water System 4CB5 S User Manual
Extron electronic Switch 5cr Plus User Manual
Fisher Price Motorized Toy Car 73690 User Manual
FUNAI DVD VCR Combo DV220TT8 User Manual
Gateway Switch MG1 1000 User Manual
GBC Binding Machine 250T User Manual
GE Power Supply EPS 301 User Manual
Gianni Industries Door EM NH300 User Manual