User’s Manual
Extender Series
VGA–UXGA Line Drivers With Audio
68-552-01 Rev. J
06 08
Download from Www.Somanuals.com. All Manuals Search And Download.
警告
安全须知 • 中文
这个符号提示用户该设备用户手册中
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必 须 使 用 有 地 线 的 供 电 系 统 供 电 。 第 三 条 线
（ 地 线 ） 是 安 全 设 施 ， 不 能 不 用 或 跳 过 。
拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后
或桌面电源的电源线，或任何接到市电系统的电源线。
电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴
露的危险电压，有触电危险。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没
有用户可以更换的零件。为避免出现触电危险不要自己
试图打开设备盖子维修该设备。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解 所 有 安 全 和 使 用 说 明 。
保存说明书 • 用户应保存安全说明书以备将来使
用。
通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用与
厂家推荐的相同或相近型号的电池。 按照生产厂的建
议处理废弃电池。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备，以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
N
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide — Extender Series
Installation and service must be performed by authorized
personnel only. These products must be used with UL
approved, grounded electrical boxes.
W
Step 1
Turn all of the equipment off and
disconnect the power cords from the
power source.
Step 2
Wall Stud
Select the installation location and
install the electrical wall box. See
“Preparing the site and installing
the wall box” in chapter 2.
Installation
Cable
Cable Clamp
The Extender AAP EX
does not require a wall
box because it will be
installed into an Extron
HSA 400 Series or
N
HSA 800 Series surface
access product.
Screws or
Nails
Step 3
into the faceplate of an Extron HSA 400 Series or
HSA 800 Series surface access product before attaching the cables.
To RGB
Video Equipment
CAUTION
For unbalanced audio, connect the
sleeve(s) to the ground contact.
DO NOT connect the sleeve(s) to
the negative (-) contacts.
NO Ground Here
Right Tip
Sleeve(s)
NO Ground Here
Left Tip
Audio
Unbalanced Output
Power
9-18 VDC
Right Ring
Right Tip
Sleeve(s)
Left Ring
Left Tip
)
.
d
r
a
Balanced Output
o
b
t
l
i
a
m
u
c
ries
r
r
i
r
y
it
c
l
o
e
n
v
N
n
i
a
e
U
le
in
a
w
-
g
o
d
l
i
e
M
g
h
t
–
in
&
n
g
o
Extenchdi ere See
m
iu
s
k
a
d
t
p
i
M
w
S
(
m
k
a
a
g
g
in
A
u
Gain
m
i
x
e
n
i
er
a
p
.
x
a
M
w
C
D
&
V
M
8
1
-
9
Sleeve (s)
Left Ring
Left Tip
Right Ring
Right Tip
Sleeve (s)
Left Ring
Left Tip
Power
9-18 VDC
Do not tin the wires!
Extender Series • Quick Start Guide
QS-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide — Extender Series, cont’d
#4 - 40 Screws
Step 4
Mount all AAPs into faceplates with AAP
openings.
AKM MAAP
EXTENDER
TER IN
Mount Extender AAP models into wall
COMPU
DIO IN
U
A
chapter 2.
Extron
Extender AKM MAAP
Line Driver
Wall Stud
Screws or Nails
#4-40 Nut w/ Captive
Washer
Cable
Step 5
Clamp
Connect
power and
turn the
AAP 102
equipment
on.
TER IN
COMPU
NDER
EXTE
UDIO IN
A
on
Extr
AAP 102
Extender AAP
Step 6
Normal –
Unity gain
Test the system and set the gain switch. Ensure that
all devices receive power. Check and adjust cabling
and gain as needed. See “Gain switch” on
page 2-12.
Medium –
Mid-level
peaking
Faceplate
and gain
Medium – Mid-level
peaking and gain
Medium – Mid-level
peaking and gain
Maximum
Max. peaking
and gain
Normal
Unity
gain
Maximum
Max. peaking
and gain
Normal
Unity
gain
Maximum –
Max. peaking
and gain
Circuit
board
Extender MK, AKM,
AUS, AAP Models
(viewed from rear)
Extender WM
Extender WM AAP
(viewed from side)
Extender D
(viewed
from front)
Step 7
Disconnect power from all the devices.
Step 8
Mount the line driver into the electrical box or the body of the HSA.
See chapter 2 of this manual, the Extender AKM MAAP Installation
Guide, or the appropriate HSA Series user’s manual.
Step 9
For the Extender D, install the Decora© faceplate.
Step 10
Restore power to the devices.
Extender Series • Quick Start Guide
QS-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Accessories ........................................................................................A-1
Extender Series • Table of Contents
TOC-i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents, cont’d
All trademarks mentioned in this manual are the properties of their respective owners.
68-552-01 Rev. J
06 08
Extender Series • Table of Contents
TOC-ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
About this Manual
This manual contains information about the Extron Extender
series line drivers, and on how to operate and configure them.
“Extender” or “line driver” are used to refer to all models
interchangeably when instructions apply to more than one
model.
About the Extender Series VGA Line Drivers
The Extron Extender Series are one-input VGA–UXGA line
drivers with audio. There are nine models in the series:
Extender AAP, Extender AAP EX, Extender WM, Extender D,
Extender WM AAP, Extender WM AUS, Extender MK,
Extender AKM UK AAP, and Extender AKM MAAP. They
boost the video signal between a laptop or desktop computer
and a monitor or projector. Each has a 300 MHz (-3 dB) video
bandwidth.
Each line driver accepts one computer-video input and one
stereo audio input. Each Extender also features one buffered
VGA-type RGB output and one stereo audio output. With
an optional Mac/VGA adapter, the Extender can also buffer
Macintosh signals.
Differences between the models
All Extender models are functionally identical but they have
mounting options.
For details about mounting the Extender AAP, Extender WM,
Extender D, Extender WM AAP, Extender WM AUS, and the
Extender MK, see “Preparing the Site and Installing the Wall
Box” in chapter 2.
For Extender AAP EX mounting instructions, refer to the user’s
manual or installation manual for the appropriate model of HSA
Hideaway Surface Access enclosure.
For Extender AKM UK AAP mounting instructions, refer to
the AKM UK Series Installation Guide (part number 68-904-01),
For Extender AKM MAAP mounting instructions, refer to
the Extender AKM MAAP Installation Guide (part number
Extender Series • Introduction
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Video signal boosting — The selectable gain/peaking settings
boost video signals to compensate for signal degradation
caused by long cables. The Extender can send a high
resolution signal up to 250 feet (76.2 m) through Extron’s
M59 Series mini high resolution cable.
Sync restoration — Each Extender restores low level sync
voltages found on many laptop PCs (as low as two volts) to
normal TTL levels.
Audio buffering — Unbalanced stereo audio inputs can be
output as balanced audio for long cable runs.
Extender Series • Introduction
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction, cont’d
Extender Series • Introduction
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation and service must be performed by
authorized personnel only. This product should
be used with a UL approved electrical box. See
“UL Requirements”, below.
C
UL Requirements
1.
2.
The Extender must be installed in an Underwriters
Laboratories (UL) listed junction box. The UL approved
electrical wall box (junction box) is not included with the
unit; the installer is responsible for obtaining and installing
the box.
The unit must be installed with accordance with the
National Electrical Code and with local electrical codes.
Installation Instructions
All of the Extenders can be mounted into furniture, a wall, an
Ackermann floorbox, or an Extron HSA 400 Series or HSA 800
Series enclosure (depending on the model).
For Extender AKM UK AAP mounting instructions, refer to the
AKM UK Series Installation Guide (part number 68-904-01).
For Extender AKM MAAP mounting instructions, refer to the
AKM MAAP Installation Guide (part number 68-1031-01).
The Extender must be installed into an Underwriters
Laboratories (UL) approved electrical wall box. The
box is not included with the Extender; the installer is
responsible for obtaining and installing the box.
C
For Extender AAP EX mounting instructions, refer to the user’s
manual or installation manual for the appropriate model of HSA
Hideaway Surface Access enclosure.
The Extender AAP EX does not require a wall box because
it will be installed into an Extron HSA 400 Series or
HSA 800 Series surface access product.
N
Preparing the Site and Installing the Wall Box
Choose a location that allows cable runs without interference.
Allow enough depth for both the wall box and the cables.
You may need to install the cables into the wall, furniture, or
conduits before installing the line driver.
•
The Extender AAP or Extender AAP EX can be installed
in an Extron two-gang, four-gang, or half rack width AAP
Architectural Adapter Plate or in the faceplate of another
Extron device that accepts AAP plates, such as an interface
or distribution amplifier. Refer to the mounting instructions
for the adapter plate or device.
Extender Series • Installation
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
The Extender AAP EX can also be installed into an
HSA 400 Series or HSA 800 Series surface access enclosure.
The Extender WM can be installed in a standard or compact
one-gang electrical wall box. This is also true for the
Extender D, though it requires a standard Decora©-style wall
plate (not included).
•
•
The Extender WM AUS can be installed in a standard or
compact Australian one-gang electrical wall box.
The Extender WM AAP can be installed in a three-gang wall
box, and its faceplate accepts up to four single height Extron
Architectural Adapter Plates (AAPs).
•
The Extender MK can be mounted into a standard, shallow
knockout switch box (also known as a KO box or MK
box) that is used in Singapore, the United Kingdom, and
Australia.
The installation must conform to national and local electrical
codes and to the Extender’s size requirements. Dimensional
drawings and templates are provided in appendix B of this
manual.
1.
Refer to the template that corresponds to the Extender
model and wall box being used.
The templates are not shown at full size. Pay attention to
the measurements shown on the templates.
N
2.
Mark the guidelines for the opening on the wall or
furniture.
•
If the Extender will be installed in a wall box, place the
box against the installation surface and draw a line on
it around the outside of the box.
•
If the Extender will be installed without a wall box
(using mud rings or fastening it directly to the wall or
furniture), measure and mark the surface for the cutout
area indicated in the template.
3.
4.
Cut out the material from the marked area.
Check the opening size by inserting the wall box (if used)
or the Extender (if no box is used) into the opening. The
box and line driver should fit easily into the opening.
Enlarge or smooth the edges of the opening if needed.
5.
6.
Feed cables through the wall box punch-out holes, and
secure them with cable clamps to provide strain relief.
Exposed cable shields (braids or foil) are potential sources
of short circuits. Trim back and/or insulate shields with
heat shrink.
Extender Series • Installation
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Metal Wall Box
Screw
Cable Clamp
Install Cable
Braided Shield
Foil Shield
Grounding outer braided and foil shields
To prevent short circuits, the outer foil shield can
be cut back to the point where the cable exits the
cable clamp. Both braided and foil shields should be
connected to an equipment ground at the other end of
the cable.
W
7.
Insert the wall box into the opening, and attach it to the
wall, stud, or furniture.
•
For the Extender WM, Extender WM AAP,
Extender WM AUS, Extender D, and the Extender AAP
or Extender AAP EX (if installed in a two- or four-gang
AAP plate), attach the wall box to the wall stud or
furniture with nails or screws, leaving the front edge
flush with the outer wall or furniture surface. See the
following illustration, which applies to one-, two-,
three-, and four-gang wall boxes.
Wall Stud
Wall Stud
Installation Cable
Cable Clamp
Installation Cable
Cable Clamp
Screws or Nails
Screws or Nails
Attaching a wall box to a wall stud
Extender Series • Installation
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
If attaching the wall box to wood, use four #8 or #10
screws or 10-penny nails. A minimum of ½ inch
(1.3 cm) of screw threads must penetrate the wood.
If attaching the wall box to metal studs or furniture,
use four #8 or #10 self-tapping sheet metal screws or
machine bolts with matching nuts.
•
For the Extender MK, pull the knockout box’s
mounting tabs forward to secure them against the
back side of the wallboard or furniture as shown in the
following illustration.
Pull mounting tab
forward.
Securing the MK knockout box to a wall or furniture
8.
Set the gain switch, and cable and test the line driver
before fastening the line driver into the wall box. The
switch and cables will be inaccessible after installation.
See “Top/Rear/Bottom Panel Features and Cabling” in
this chapter for details.
Extender Series • Installation
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Front Panel Features and Cabling
AUDIO IN
COMPUTER IN
6
EXTENDER MK
EXTENDER AKM MAAP
COMPUTER IN
1
2
3
4
1
AUDIO IN
1
2
3
4
COMPUTER IN
AUDIO IN
EXTENDER WM AUS
Faceplate screws — These secure the
faceplate to the rest of the line driver.
Faceplate dimensions are provided in
appendix B of this manual.
a
Do not remove these faceplate screws or the jack screw nuts on
either side of the PC Input connector while the line driver is
attached to the wall. If these screws are removed, the detached
line driver may fall down inside the wall.
N
To replace the standard faceplate with a customized faceplate:
1.
Set the line driver in an accessible place (do not do this while
the line driver is installed in a wall or furniture),
and remove the faceplate screws and the jack screw
nuts on either side of the PC Input connector.
Jack Screw Nuts
2.
3.
Fasten the new faceplate to the line driver with the
faceplate screws.
Reattach the jack screw nuts.
Power/signal LED — This LED lights
• amber to indicate that the Extender is receiving power
b
• green to indicate that an active sync signal is present at the input
and the Extender is receiving power
The LED remains lit amber when the input signal is HDTV
component video, RGsB, or RsGsBs.
N
Extender Series • Installation
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
1
1
4
3
2
1
EXTENDER AKM UK AAP
1
5
1
2
3
AUDIO IN
AUDIO IN
COMPUTER IN
COMPUTER IN
4
1
EXTENDER WM AAP
EXTENDER WM
Tip (L)
Audio input connector —
Plug a 3.5 mm stereo plug
into this jack for
unbalanced audio input.
Wire the male plug as
shown in the figure at
right.
c
d
Ring (R)
2
3
AUDIO IN
COMPUTER IN
Sleeve (
)
4
3.5 mm Stereo Plug
Connector
(unbalanced)
RGB video input connector (PC Input) — Attach
a cable from the computer to the Extender via this
female 15-pin HD connector.
Opening for Architectural Adapter Plates (AAPs) — The
Extender WM AAP can have up to four optional adapter plates
attached here at one time. The Extender AKM UK can hold up to
three optional adapter plates at one time. The adapter plates allow
for a variety of types of audio/video connectors or another
device such as the Extender AAP to be added to the faceplate.
e
Blank plates are included with the Extender WM AAP,
Extender AKM UK, and Extender AKM MAAP to cover unused
spaces.
Extender Series • Installation
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Other adapter plates must be ordered separately. They also
must be attached to the faceplate and cabled before the line
driver is installed in the wall or furniture. The screws needed
for installing the adapter plates are built into the plates, so no
additional screws are needed.
1.
Remove the blank plates from the Extender by unscrewing
the nuts that fasten the plates to the faceplate.
2.
Insert the adapter
plate screws
through the holes
A
UDIO IN
in the faceplate.
Attach the adapter
plates to the
COMP
TER IN
Adapter Plate
faceplate with the
provided captive
washers and #4-40
nuts.
#4-40 Nut with
Captive Washer
EXTENDER
WM AAP
3.
Attach the output
cables to the rear
connectors of the
Extender WM AAP
(up to 4 plates)
adapter plates. Soldering is required for some connectors.
Attach foil and braided shields to ground connections.
Opening for Mini Architectural Adapter Plates (MAAPs) —
The Extender AKM MAAP can have up to three optional MAAP
adapter plates attached here at one time to allow for a variety of
types of audio/video connectors or another device to be added
to the faceplate.
f
One double-size and one single-size blank plate are included
with the Extender AKM MAAP to cover unused spaces. Other
adapter plates must be ordered separately. They also must be
attached to the faceplate and cabled before the line driver is
installed in the wall, floor box, or furniture. The screws needed
for installing the adapter plates are included with the MAAPs,
so no additional screws are
needed.
#4 - 40 Screws
Refer to the picture at right and
the following steps.
P
A
A
M
M
K
A
R
E
D
N
E
T
IN
X
R
E
E
T
U
P
M
O
C
1.
Insert the MAAP into the
Extender AKM MAAP’s
faceplate opening.
N
I
IO
D
U
A
2.
Using an Allen wrench,
secure the MAAP to the
faceplate with the provided
machine screws.
Extron
Extender AKM MAAP
Line Driver
Extender Series • Installation
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Top/Rear/Bottom panel Features
and Cabling
Extender MK, Extender AAP, Extender AAP EX, Extender WM AUS,
Extender AKM UK AAP, and Extender AKM MAAP
top view
Extender WM, Extender WM AAP,
and Extender D
rear view
3
1
2
1
Extender MK/AAP/AAP EX,
Extender AKM UK AAP,
Extender AKM MAAP,
Extender WM AUS
rear view
1
2
4
(Side)
3
4
Extender MK, Extender AAP, Extender AAP EX, Extender WM AUS,
Extender AKM UK AAP, and Extender AKM MAAP
bottom view
3
Audio output connector
a
b
RGB video output
connectors
Power connector
Gain switch
c
d
Extender Series • Installation
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Audio output connector — Insert wires into and tighten the
a
screws on this 3.5 mm, 5-pole direct insertion captive screw
connector for unbalanced or balanced audio output. Wire the
connector as shown in the following illustrations.
Connect the sleeve to ground (Gnd). Connecting the
sleeve to a negative (-) terminal will damage the audio
output circuits.
C
CAUTION
For unbalanced audio, connect the
sleeve(s) to the ground contact.
DO NOT connect the sleeve(s)
to the negative (-)
contacts.
NO Ground Here
Right Tip
Sleeve (s)
NO Ground Here
Left Tip
.)
d
ar
o
s
b
l
it
ie
a
u
r
m
n
U
e
irc
r
o
y
l
it
c
S
e
r
v
le
in
N
in
e
Audio
r
a
w
lo
-
g
e
d
i
a
d
e
g
M
g
h
n
t
–
&
e
n
t
o
m
u
a
e
in
k
x
i
is
d
E
h
e
M
p
itc
w
(S
Unbalanced Output
m
g
u
in
k
in
a
Gain
m
i
a
x
e
a
p
.
M
x
g
wer DC
V
8
a
o
&
M
P
-1
9
Right Ring
Right Ring
Right Tip
Sleeve (s)
Left Ring
Left Tip
Right Tip
Sleeve (s)
Left Ring
Left Tip
Balanced Output
Power
9-18 VDC
Do not tin the wires!
Extender WM AUS is shown here wired for balanced
audio output; the circuit board configuration is the same
for the Extender MK, Extender AAP, Extender AAP EX,
Extender AKM UK AAP, and Extender AKM MAAP
Extender Series • Installation
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
For unbalanced audio, connect the
sleeve(s) to the ground contact.
DO NOT connect the sleeve(s) to the
negative (-) contacts.
NO Ground Here
Right Tip
Sleeve(s)
NO Ground Here
Left Tip
Power
9-18 VDC
Audio
Unbalanced Output
Right Ring
Right Tip
Sleeve(s)
Left Ring
Left Tip
Balanced Output
Right Ring
Right Tip
Sleeve (s)
Left Ring
Left Tip
Do not tin the wires!
Extender WM is shown here wired for balanced
audio output; the circuit board configuration is the same
for the Extender WM AAP and the Extender D
RGB video output connectors — Attach coaxial cables from the
Extender to the display device via these female BNC connectors.
These BNCs are on pigtail wires secured to the Extender by tie
wrap.
b
c
Power connector — Connect a 9 VDC to 18 VDC power supply
to this 3.5 mm, 2-pole direct insertion
captive screw connector. Wire the
+ or –
– or +
connector as shown here. Polarity is not
important.
Do not tin the wires!
For best results and to reduce the risk of short circuits,
trim just 3/16” (5 mm) of the jacket from the wires. Do
not tin the wires.
C
Extender Series • Installation
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Gain switch —
d
4
Medium – Mid-level
peaking and gain
Maximum
Max. peaking
and gain
Normal
Unity
gain
Extender MK, Extender AAP,
Extender AAP EX, Extender WM AUS,
Extender AKM UK AAP, and Extender AKM MAAP
gain switch location (access from the rear)
Faceplate
4
Medium – Mid-level
peaking & gain
Maximum
Normal
Unity
gain
Max. peaking
& gain
Circuit
board
Extender WM and Extender WM AAP
gain switch location
(access from the side)
Circuit
board
Normal –
Unity gain
AUDIO IN
Medium –
Mid-level
peaking
COMPUTER IN
and gain
4
Maximum –
Max. peaking
and gain
Extender D gain switch location
(like the Extender WM switch,
but accessible from the front)
Extender Series • Installation
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
To compensate for cable resistance and capacitance, use a small
screwdriver to slide this switch to select the level of video gain
that yields the sharpest, smear-free picture.
Normal — unity gain (no signal boost)
Medium — mid-level peaking and gain
Maximum — maximum amount of peaking and gain. Select
this for use with longer cables.
Adjust the gain before installing the Extender into a
wall, furniture, or equipment, as the gain switch will be
inaccessible after installation.
N
Extender Series • Installation
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Mounting the Extenders
Mounting the Extender AAP or Extender AAP EX
into an AAP wall plate or device faceplate
The Extender AAP or Extender AAP EX and any other adapter
plates must be attached to a device faceplate or AAP wall
plate and cabled before the device or wall plate is pretested or
installed in a wall or furniture.
1.
Before any user-supplied cables are attached, insert
the Extender AAP or Extender AAP EX’s output BNC
connectors and wires through the opening in the front of
the faceplate.
2.
3.
Insert the AAP’s threaded standoffs through the holes in
the device’s faceplate or AAP wall plate.
Using the provided #4-40 nuts and captive washers, secure
the Extender to the faceplate/wall plate.
Wall Stud
Screws or Nails
#4-40 Nut w/ Captive
Washer
Cable
Clamp
AAP 102
COMPUTE
UDIO IN
EXTENDER
A
on
Extr
AAP 102
Extender AAP
Installation Cable
Mounting the Extender AAP or Extender AAP EX to a
device or wall plate
Extender Series • Installation
2-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron
HSA 822
Two Screws
Each Side
Front Panel
A
U
D
I
O
I
N
CO
H
M
S
A
PUTER IN
8
2
2
Cable
Extron
Extender AAP EX
#4-40 Nut
w/ Captive
Washer
HV - 18”
Connects to
AAP Cable
RGB - 20”
Mounting the Extender AAP EX to an HSA faceplate
4.
5.
Repeat steps 1, 2, and 3 to mount other AAPs. Cover any
openings in the faceplate with blank plates (provided).
Be sure to include the AAP connectors as part of the
installation pretest before final installation of the faceplate.
For more detailed installation information, refer to the
installation guide shipped with the faceplate or the HSA.
Extender Series • Installation
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Pre-installation testing/troubleshooting
Before mounting the line driver, test the system to make sure
that the connections and settings are correct.
1.
2.
Apply power to the line driver. The power/signal LED on
the line driver lights amber to indicate that it is receiving
power.
If the LED does not light, check the wiring at both the line
driver and the power supply, and make sure the power
supply is connected to a power source.
If the image does not appear or there is no sound
1.
2.
Make sure that all the devices are powered on.
Ensure that the connectors are wired correctly at both
ends of the cables. Audio cables must be wired for an
unbalanced stereo input signal and for the appropriate
(unbalanced or balanced) output signal.
3.
If the input is from a laptop computer and no picture
appears, use a laptop breakout cable for the input
connection. Check the computer’s user’s guide or contact
Extron to determine if special commands are required
to output video to the external video port. Also, many
laptops’ screens shut off after the external video port is
activated.
4.
Call the Extron S3 Sales and Technical Support Hotline if
the image still does not appear or there is no sound.
If the image is not displayed correctly
1.
If the picture is too bright or too dark, if the edges of the
image seem to exceed their boundaries, or if thin lines and
sharp edges look thick and fuzzy, change the gain setting.
See “Gain switch” on page 2-12.
If the picture appears and is stable, but it has ghosting
or blooming, verify that the video input is properly
terminated. If the problem is not resolved by changing the
termination, try using a different input cable. Poor quality
or damaged cable can cause ghosting and blooming.
2.
If the picture still is not displayed correctly, call the Extron
S3 Sales and Technical Support Hotline.
Once the system has been cabled and tested, the line driver can
be installed in the wall, furniture, or equipment.
Extender Series • Installation
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Extender WM, Extender WM AAP, or
Extender WM AUS to the wall box
1.
Remove power from the line driver by disconnecting the
power supply.
2.
Place the line driver through the opening in the wall or
furniture and into the wall box. Take care not to damage
the output cables, which fit behind the line driver at the
back of the wall box.
3.
Mount the line driver’s faceplate to the wall box with
machine screws as shown in the following illustration.
Wall Stud
Screws or Nails
Installation
Cable
Cable Clamp
N
I
O
I
D
U
A
P
A
A
M
W
N
R
E
E
D
T
U
EN
T
P
M
EX
O
C
Extender WM AAP
Mounting the line driver to the wall box
4.
Reconnect the power supply and restore power to the
equipment.
Extender Series • Installation
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Mounting the Extender D
1.
Remove power from the line driver by disconnecting the
power supply.
2.
Place the Extender D through the opening in the wall or
furniture and into the wall box. Take care not to damage
the output cables, which fit behind the line driver at the
back of the wall box.
3.
Mount the Extender D to the wall box with machine screws
as shown in the following illustration.
Wall Box
N
I
IO
T
D
U
A
N
I
Wall opening
is flush with
edge of box.
R
E
U
P
M
O
C
Extron
Extender D
VGA-QXGA
Line Driver
with Audio
Decora
Faceplate
Mounting the Extender D to the wall box
4.
5.
Attach the Decora wall plate to the Extender D as shown in
the illustration above.
Reconnect the power supply and restore power to the
equipment.
Extender Series • Installation
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the Extender MK to the knockout box
1.
Remove power from the line driver by disconnecting the
power supply.
2.
Place the line driver through the opening in the wall or
furniture and into the knockout box. Take care not to
damage the cables, which lie next to the line driver at the
side of the box.
3.
Mount the line driver’s faceplate to the knockout box with
machine screws as shown in the following illustration.
M59 Mini HR Cable
Double Wide
Dry Lining Box
3.5 x 30 mm
Screw
COMPUTER N
I
N
IO
D
U
A
K
M
R
E
D
N
E
T
X
E
Extender MK
Mounting the Extender MK to the knockout box
4.
Reconnect the power supply and restore power to the
equipment.
Extender Series • Installation
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Application Diagrams
Mini HR Cable
Projector
Wall Stud
Audio
IN
IO
D
Laptop
U
A
N
I
R
E
T
U
P
M
O
C
w/ Audio
M
W
R
E
D
N
E
T
X
E
Extender WM
Mini HR
Cable
Projector
Laptop w/ Audio
IN
R
TE
U
P
M
CO
R
E
D
N
E
IN
T
X
IO
D
E
U
A
Extender AAP
IFT
SH
H.
R
TM
P
S
O
IT
D
A
N
O
H
M
IT
W
X
MIN/MA
8
6
4
B
PU
G
IN
R
OR
IT
N
O
M
IO
D
R
O
U
A
I
T
N
O
M
O
N
RGB 468xi
Projector
Extron
Extender AKM MAAP
Line Driver
SVGA Compatible
Computer w/ Audio
P
A
A
M
M
K
A
R
E
D
N
E
T
IN
X
R
E
E
T
U
P
M
O
C
I
N
IO
D
U
A
Laptop
Extender Series • Installation
2-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, and Accessories
Specifications
Video
Gain................................................. 0 dB, 0.6 dB, 1.2 dB, selectable (when
input is 0.7 Vp-p, output is 0.7 V, 0.75 V,
0.8 Vp-p)
Bandwidth...................................... 300 MHz (-3 dB)
ID bits are terminated (pins 4 and 11).
N
Video input
Number/signal type..................... 1 VGA–QXGA RGBHV, RGBS, RGsB,
RsGsBs, HDTV component video
Connectors ..................................... (1) 15-pin HD female
Nominal level ................................ 1.0 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of
component video
Minimum/maximum levels........ Analog: 0.3 V to 1.5 Vp-p with no offset at
unity gain
Impedance...................................... 75 ohms
Horizontal frequency.................... 15 kHz to 135 kHz
Vertical frequency.......................... 30 Hz to 170 Hz
Input coupling............................... DC
Video output
Number/signal type..................... 1 VGA–QXGA RGBHV, RGBS, RGsB,
RsGsBs, HDTV component video
Connectors
Extender AAP EX.............. 5 BNC female on 18" (HV) and 20" (RGB)
pigtails
All other models................ 5 BNC female on 3" pigtails
Nominal level ................................ 1.0 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of
component video
Minimum/maximum levels........ Analog: 0.3 V to 1.5 Vp-p with no offset at
unity gain
Impedance...................................... 75 ohms
DC offset......................................... ±5 mV with input at 0 offset
Return loss...................................... <-35 dB @ 5 MHz
Extender Series • Specifications, Part Numbers, Accessories
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Sync
Input type....................................... RGBHV, RGBS, RGsB, RsGsBs, bi-level
and tri-level component video sync
Output type.................................... RGBHV, RGBS, RGsB, RsGsBs, bi-level
and tri-level component video sync
Input level ...................................... 2.0 V to 5.0 Vp-p
Output level................................... TTL: 5 Vp-p, unterminated
Input impedance ........................... 510 ohms
Output impedance........................ 75 ohms
Max. propagation delay ............... 18.8 ns
Max. rise/fall time ........................ 4 ns
Polarity............................................ Positive or negative (follows input)
Audio
Gain................................................. Unbalanced output: 0 dB; balanced output:
+6 dB
Frequency response ...................... 20 Hz to 20 kHz, ±0.5 dB
THD + Noise.................................. 0.025% @ 1 kHz, 0.020% @ 20 kHz at
nominal level
S/N.................................................. >90 dB at rated maximum output
Stereo channel separation ............ >75 dB @ 20 Hz to 20 kHz
Audio input
Number/signal type..................... 1 stereo, unbalanced
Connectors ..................................... (1) 3.5 mm mini stereo jack
Impedance...................................... >10k ohms unbalanced, DC coupled
Nominal level ................................ -10 dBV (316 mVrms)
Maximum level.............................. +6 dBV, (unbalanced) at 1% THD+N
Audio output
Number/signal type..................... 1 stereo, balanced/unbalanced
Connectors
Extender WM, Extender WM AUS, Extender WM AAP, Extender D
(1) 3.5 mm direct insertion captive screw
connector, 5 pole
Extender AAP, Extender AAP EX, Extender MK,
Extender AKM UK AAP, Extender WM AUS, Extender AKM MAAP
(1) 3.5 mm captive screw connector, 5 pole
Impedance...................................... 50 ohms unbalanced, 100 ohms balanced
Extender Series • Specifications, Part Numbers, Accessories
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, Accessories, cont’d
Nominal level ................................ -2 dBu, balanced; -10 dBV unbalanced
Maximum level (Hi-Z) ................. +14 dBu, balanced, at 1% THD+N
Maximum level (600 ohm)........... +6 dBm, balanced, at 1% THD+N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
N
General
External power supply................. 100 VAC to 240 VAC, 50/60 Hz, external;
to 12 VDC, 1 A (max.), regulated
Power input requirements........... 12 VDC, 0.2 A
Temperature/humidity................ Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Cooling ........................................... Convection, no vents
Mounting
Floor box mount
ExtenderAKM UKAAP Ackerman UK floor box mountable
Extender AKM MAAP Ackerman floor box mountable in either a
GB2 or a GB3 mounting space
Furniture mount
Extender AAP EX...... Mountable in an optional HSA 800 Series
or HSA 400 Series Hideaway Surface
Access Enclosure, which can be mounted
in furniture
Extender WM AUS.... Wall or furniture mountable in a standard
Australian electrical wall box
Extender AAP............ Wall or furniture mountable with optional
AAP mounting faceplates
All other models........ Wall or furniture mountable in a standard
U.S. electrical wall box
Enclosure type ............................... Metal (Extender D has a metal faceplate
and a plastic Decora wall plate.)
Enclosure dimensions
Extender AAP, Extender AAP EX
Faceplate..................... 1.4" H x 3.5" W x 0.1" D
(3.6 cm H x 8.9 cm W x 0.3 cm D) (double
space high AAP plate)
Buffer........................... 1.1" H* x 2.75" W x 1.2" D
(2.8 cm H* x 7.0 cm W x 3.0 cm D)
(*Height excludes BNC connectors and
cables.)
Extender Series • Specifications, Part Numbers, Accessories
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Extender WM
Faceplate..................... 4.5" H x 2.8" W x 0.1" D
(11.4 cm H x 7.1 cm W x 0.3 cm D) (1 gang)
Buffer........................... 2.7" H x 1.8" W x 0.75" D*
(6.9 cm H x 4.6 cm W x 1.9 cm D*)
(*Depth excludes BNC connectors and
cables.)
Extender WM AUS
Faceplate..................... 3.0" H x 4.7" W x 0.1" D
(7.6 cm H x 11.8 cm W x 0.3 cm D)
Buffer........................... 2.75" H* x 1.1" W x 1.2" D
(7.0 cm H* x 2.8 cm W x 3.0 cm D)
(*Height excludes BNC connectors and
cables.)
Extender WM AAP
Faceplate..................... 4.5" H x 6.4" W x 0.1" D
(11.4 cm H x 16.3 cm W x 0.3 cm D)
(3 gang)
Buffer........................... 2.7" H x 1.8" W x 0.75" D*
(6.9 cm H x 4.6 cm W x 1.9 cm D*)
(*Depth excludes BNC connectors and
cables.)
Extender MK
Faceplate..................... 3.4" H x 5.7" W
(8.6 cm H x 14.4 cm W) (UK knockout box
size)
Buffer........................... 1.1" H* x 2.75" W x 1.2" D
(2.8 cm H* x 7.0 cm W x 3.0 cm D)
(*Height excludes BNC connectors and
cables.)
Extender AKM UK AAP
Faceplate..................... 3.0" H x 8.1" W x 0.6" D
(7.6 cm H x 20.6 cm W x 1.5 cm D)
Buffer........................... 1.1" H* x 2.75" W x 1.2" D
(2.8 cm H* x 7.0 cm W x 3.0 cm D)
(*Height excludes BNC connectors and
cables.)
Extender AKM MAAP
Faceplate..................... 1.67" H x 6.12" to 7.85" W* x 3.0" D
(4.1 cm H x 15.5 cm to 19.9 cm W* x
7.6 cm D)
*Width is adjustable.
Buffer........................... 1.8" H x 4.4" W x 3.0" D
(4.6 cm H x 11.2 cm W x 7.6 cm D)
Extender Series • Specifications, Part Numbers, Accessories
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, Accessories, cont’d
Extender D
Faceplate..................... 2.6" H* x 1.3" W x 0.1" D
(6.6 cm H* x 3.3 cm W x 0.3 cm D)
(Fits the opening in a 1 gang Decora
faceplate. *Height is 3.8" [9.7 cm] including
mounting tabs.)
Buffer........................... 2.7" H x 1.8" W x 0.75" D*
(6.9 cm H x 4.6 cm W x 1.9 cm D*)
(*Depth excludes BNC connectors and
cables.)
Product weight
Extender AAP, Extender AAP EX, Extender WM
0.2 lbs (0.1 kg)
Extender WM AUS............ 0.3 lbs (0.1 kg)
Extender WM AAP ........... 0.4 lbs (0.2 kg)
Extender MK...................... 0.5 lbs (0.3 kg)
Extender AKM UK AAP .. 0.6 lbs (0.3 kg)
Extender AKM MAAP...... 1.2 lbs (0.5 kg)
Extender D ......................... 0.2 lbs (0.1 kg)
Shipping weight
Extender AAP, Extender AAP EX
2 lb (1 kg)
All other models................ 3 lbs (2 kg)
Vibration......................................... ISTA 1A in carton (International Safe
Transit Association)
Regulatory compliance
Safety................................... C-tick, CUL, UL
EMI/EMC .......................... CE, C-tick, FCC Class A, ICES, VCCI
MTBF............................................... 30,000 hours
Warranty......................................... 3 years parts and labor
All nominal levels are at 10%.
N
N
Specifications are subject to change without notice.
Extender Series • Specifications, Part Numbers, Accessories
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Ordering Information
This section lists part numbers for each Extender and
Extender kit.
Model
Part numbers
Extender AAP1
(black, white, RAL9010 white)
70-147-12, -22, -52
Extender AAP EX1 (black)
70-147-72
Extender WM1 (black, white)
60-398-12, -22
Extender WM AAP1
(gray, black, white, RAL9010 white)
60-405-02, -12, -22, -52
Extender WM AUS1 (white)
Extender D1, 4 (black, white)
60-398-32
60-759-12, -22
Extender MK1
(black & white, RAL9010 white)
60-406-12, -52
Extender AKM UK AAP1, 2 (gray)
Extender AKM MAAP1, 2 (black)
60-627-01
60-727-02
1An international, 12 VDC, 2 A, external power supply (#70-055-01) and this user’s
manual (#68-552-01) ship with all Extender products.
2In addition, a double-size, blank AAP (#70-090-02); a single-size, blank AAP
(#70-090-01); and the Extender AKM UK AAP Installation Guide (#68-904-01) ship
with the Extender AKM UK AAP.
3In addition, a double-size, blank MAAP (#991994-2); a single-size, blank MAAP
(#991993-2); and the Extender AKM MAAP Installation Guide (#68-1031-01) ship
with the Extender AKM MAAP.
4The Extender D does not include a Decora wall plate. The wall plates are available
at local electrical supply stores.
Accessories
Mounting accessories
AAP mounting accessories
Part numbers
AAP 102 – 2 gang wall plate
(gray, black, white, RAL9010 white)
60-300-01, -02, -03,
-05
AAP 104 – 4 gang wall plate
(black, white, RAL9010 white)
60-301-02, -03, -05
60-302-01, -02, -03
60-303 -02, -03
AAP 201 – half rack wide, 1U high AAP
mounting frame (gray, black, white)
AAP 201 – half rack wide, 1U high AAP
mounting frame (black, white)
Extender Series • Specifications, Part Numbers, Accessories
A-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, Accessories, cont’d
Mud rings/mounting brackets
Part numbers
MR 100 – 1-gang modular plastic
mud ring (black, white)
70-519-12, -13
MR 100D – 1-gang Decora®-style
modular plastic mud ring (black)
70-581-12
70-519-32, -33
70-581-32
MR 300 – 3-gang modular plastic
mud ring (black, white)
MR 300D – 3-gang Decora®-style
modular plastic mud ring (black)
MK 2-gang metal mounting bracket/
mud ring (black, white, RAL9010 white
70-086-16, -26, -56
Cables
Miscellaneous cables
Part numbers
SY VGAM-RGBHVM cable – 15-pin
VGA male to 5 BNC male, 6'
26-533-02
SY VGAM-RGBHVF cable – 15-pin VGA
male to 5 BNC female, 3'
26-548-12
Male-to-female VGA with audio
cables
Part numbers
VGA-A M-F MD/3 /6 /12 /25 /35 /50
– with molded connectors –
3' (90 cm), 6' (1.8 m), 12' (3.6 m),
25' (7.6 m), 35' (10.6 m), 50' (15.2 m)
26-491-01, -02, -03,
-04, -07, -08
VGA-A M-F BK/3 /6 /12 /25 /35 /50
– with backshell connectors –
3' (90 cm), 6' (1.8 m), 12' (3.6 m),
25' (7.6 m), 35' (10.6 m), 50' (15.2 m)
26-491-09, -10, -11,
-12, -06, -05
Extender Series • Specifications, Part Numbers, Accessories
A-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions and Templates
Dimensions
The drawings in this section are not full size.
Do not scale.
N
All dimensions are given in inches.
N
Extender AAP and Extender AAP EX dimensions
0.250”
3.000” (REF)
(REF)
0.050”
(REF)
DETAIL A
ø 0.125 THRU WITH
ø 0.220 X 100° C'SINK
NEAR SIDE (2 PLACES)
ø 0.250” THRU
ø 0.125” THRU
1.400
R 0.040 (TYP)
1.045
AUDIO IN
COMPUTER IN
0.700 (REF)
0.650
0.345
0.000
0.345
(REF)
DETAIL A
0.984
0.806
ø 0.125 THRU
(2 PLCS)
10°
(2 PLCS)
R 0.132“
(TYP)
Extender Series • Dimensions and Templates
B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Extender WM dimensions
ø 0.156 THRU WITH
ø 0.290 X 82° C'SINK
(2 PLACES)
0.000
0.610
1.107
ø 0.125 THRU
1.550
AUDIO IN
ø 0.330 THRU
WITH
2.010
ø 0.562 C'BORE
0.070 DEEP
COMPUTER IN
2.570
3.392
3.890
EXTENDER WM
4.500
Extender Series • Dimensions and Templates
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions and Templates, cont’d
Extender AKM MAAP dimensions
4X R 0.125”
2X 0.06” X 45°
2X R
+0.000
-0.015
3.000
2X R 0.062
2X 2.350
A
2X 2.250”
1.975
1.750
2X Ø 0.150”
THRU
1.250
1.025
A
2X 0.750”
0.000”
2X 0.650
1.675
0.275
0.000
(0.075”)
Extender Series • Dimensions and Templates
B-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Extender D dimensions
1.290”
2X 0.062” X 45°
0.333”
0.625”
0.223”
0.399”
2X Ø 0.106” THRU
BOTH SIDES
2X 0.111”
2X EXTRUSION FOR
#6-32 SCREW
TAPPING
2X 0.125”
(0.223”)
Ø 0.132” THRU
Ø 0.258” THRU
2.610”
2.005”
1.545”
0.984”
0.905”
0.359
0.000”
0.111”
0.330”
Extender Series • Dimensions and Templates
B-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions and Templates, cont’d
Templates
Always check and use the dimensions given in this appendix.
N
Extender WM template
Cut-out Template for the Extron
Extender WM
2.79"
(7.09 cm)
Top Panel
2.24"
(5.59 cm)
SURFACE
CUT-OUT
AREA FOR
MOUNTING
4.13"
(10.49 cm)
4.50"
(11.43 cm)
Location of
Extender AAP
Circuit Board
Cut-out Line
for Installing
the Electrical
Box
FULL SIZE
Extender Series • Dimensions and Templates
B-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Extender WM AAP template
Cut-out Template for the Extron Extender WM AAP
4.5"
(11.43 cm)
Location of Extender AAP
Circuit Board
Top Panel
6.4"
(16.3 cm)
SURFACE
CUT-OUT AREA
FOR MOUNTING
Cut-out line
for installing
the electrical box.
FULL SIZE
Extender Series • Dimensions and Templates
B-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions and Templates, cont’d
Extender MK template
Cut-out Template for the Extron
Extender MK
3.38"
(8.56 cm)
1.24"
(3.14 cm)
Top
Panel
2.94"
(7.46 cm)
5.70"
(14.48 cm)
SURFACE
CUT-OUT
AREA
Location of
Extender AAP
Circuit Board
FOR
MOUNTING
To install an
Extender MK
directly into
furniture, cut
along this line.
FULL SIZE
Extender Series • Dimensions and Templates
B-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Extender WM AUS template
Cut-out Template for the Extron
Extender WM AUS
3.00"
(7.62 cm)
Top Panel
1.24"
(3.14 cm)
SURFACE
CUT-OUT
AREA FOR
MOUNTING
2.94"
(7.46 cm)
4.65"
(11.81 cm)
Location of
Extender AAP
Circuit Board
To install
the Extender
WM AUS
directly into
furniture,
cut along
this line.
FULL SIZE
Extender Series • Dimensions and Templates
B-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions and Templates, cont’d
Extender Series • Dimensions and Templates
B-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Europe, Africa, and the Middle East:
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805, USA
Asia:
Japan:
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or non-
Extron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron Electronics, USA
1230 South Lewis Street
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Japan
+81.3.3511.7655 FAX +81.3.3511.7656
© 2008 Extron Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|