User Guide
IP Link®
IPL T PC1
IPL T PC1i
IP Link Power Control Interfaces
68-738-10 Rev. B
09 11
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
The Class A limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at his own expense.
NOTE: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with
the unit to ensure compliance with FCC emissions limits.
For more information on safety guidelines, regulatory compliances, EMI/EMF compliance, accessibility, and
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventions Used in this Guide
Notifications
In this user guide, the following are used:
WARNING: A warning warns of things or actions that might cause injury, death, or
other severe consequences.
CAUTION: A caution indicates a potential hazard to equipment or data.
NOTE: A note draws attention to important information.
TIP: A tip provides a suggestion to make working with the application easier.
Software Commands
Commands are written in the fonts shown here:
^ARMerge Scene,,Op1 scene 1,1^B51^W^C
[01]R000400300004000080000600[02]35[17][03]
EX!*X1&*X2)*X2#*X2!CE}
NOTE: For commands and examples of computer or device responses mentioned
in this guide, the character “0” is used for the number zero and “O”
represents the capital letter “o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the Filemenu, select New.
Click the OKbutton.
Copyright
© 2011 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
IPL T PC1 • Contents
v
Download from Www.Somanuals.com. All Manuals Search And Download.
IPL T PC1 • Contents
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This section provides an overview of the Extron IPL T PC1 and IPL T PC1i IP Link® Power
Control Interfaces, and describes their features features. Topics covered in this section are:
•
•
•
•
About this Guide
This guide contains information about the Extron IPL T PC1 and IPL T PC1i, including
explanations of how to install, configure, and operate them. Unless otherwise specified,
“IPL T PC1” and “PC1” refer to both product versions throughout this guide.
About the IPL T PC1
The IPL T PC1 and IPL T PC1i are Ethernet-based power management devices that can
control and schedule AC power on and off. Monitoring of various device conditions is also
available with Global Configurator® (GC 3.3) software. The IPL T PC1i is an international
version, configured for 220 VAC with an IEC connector.
The PC1 and PC1i ports include a LAN port, a bidirectional RS-232 port, an IR output port,
and a contact closure input port. These ports provide integration of power control, serial
device control, IR device control, and input sensing in a single device that can be mounted
on a rack or behind a display device or kiosk.
The PC1 can be a stand-alone control device or as one of many nodes in a distributed
control system environment.
Features
•
Remote powering a device on and off — Centralized management features
such as Telnet allow remote powering on and off of a plasma display, camera, video
conferencing equipment, switcher, or other audio/video device. The Power button on
the front panel lets you turn power on and off to the connected device, while an LED to
the lower-right of the Power button lights green to indicate that the device is receiving
power.
•
•
•
RS-232 control — The bidirectional serial port on the rear panel, along with an Extron
serial driver, enables RS-232 control of an output device.
IR control — An IR port on the rear panel enables unidirectional device control via an IR
emitter, supported by Extron IR drivers.
Contact closure input port — This port can detect a closed circuit between an input
and ground, and trigger an event that has been set up in GC 3.3 (for example, set off an
alarm, turn on a light, or notify you by e-mail that an event has occurred).
IPL T PC1 • Introduction
1
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Industry standard Ethernet protocols — The PC1 uses standard Ethernet and TCP/IP
communication protocols, including ARP (Address Resolution Protocol), DHCP (dynamic
host configuration protocol), TCP/IP (Transmission Control Protocol/Internet Protocol),
Telnet, and HTTP (HyperText Transfer Protocol).
•
•
Integral high-performance web server — The PC1 has a built-in web server with
memory available for storing device drivers, GlobalViewer®, and custom user web pages.
Configuration utility — Global Configurator software, a free, easy to use
Windows®-based configuration utility, makes product setup simple and intuitive; no
programming knowledge is required.
•
•
•
E-mail capabilities to enable support — With e-mail notification, technical support
administrators can receive failure and service messages through an e-mail-enabled cell
phone, PDA, pager, or Internet e-mail account.
Web-based A/V asset management — When used with GlobalViewer software,
the PC1 provides a powerful, flexible way to manage, monitor, and control a projector,
flat panel display, and so on, using a standard Ethernet network.
Scheduling of power and executive mode — Power to an output device can be
scheduled using the web pages, Simple Instruction Set (SIS™) commands, or Global
Configurator. Front panel lockout (executive mode) can also be scheduled by these
methods.
•
Easy configuration and control — You can easily control the PC1 using:
•
•
•
The Internet Explorer browser (V5.5 or later)
A web-based interface
DataViewer (or a standard Telnet client application)
•
•
Extensive library of device drivers — Device drivers allow Extron products to control
various display and source devices, such as projectors, flat-panel displays, and DVD
players. Extron has produced thousands of fully tested and uniformly modeled RS-232
and IR device drivers.
Direct port access — Use existing software programs to control a device that has
no Ethernet support. Any existing Extron product with a serial control port can be
interfaced with a LAN.
•
•
•
Built-in multi-level security — You can control access to devices attached to the
interface. Two levels of password protection provide appropriate security.
Simultaneous multi-user support — Each PC1 interface supports multiple concurrent
users, improving system throughput.
Multiple mounting options — The PC1 can be placed on a tabletop, for which four
feet are provided and can be attached. Optional hardware for mounting the unit under
a desktop or podium or on a rack shelf is not included, but may be ordered separately.
IPL T PC1 • Introduction
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Diagram
The following application diagram shows an example of how devices can be connected to
the IPL T PC1 or the IPL T PC1i.
Remote User
Control and
Administrator
Monitoring
Plasma
Display
AC Power
DVD
Extron
RS-232
IR Emitter
TCP/IP
Network
M
CO
N
LA
V
+5
RX
TX
IR
INPUT
z
G
50/60H
S
Extron
IN
200-240V
X
Ethernet
IPL T PC1i
Ethernet Control
Interface
WER OUTPUT 10A MA
O
P
X
10A MA
ON
Kiosk
Button
Figure 1. Connection Diagram for an IPL T PC1
IPL T PC1 • Introduction
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and
Rear Panel
This section describes:
•
•
•
Installation Overview
To install and set up an IPL T PC1 interface:
1. Disconnect power from the PC1 interface and the output device (plasma display, VCR,
projector, and so forth).
3. Plug the PC1 power cord into an AC wall outlet.
4. Connect a LAN Ethernet cable from your computer to the RJ-45 port on the PC1 rear
panel to establish a link to the network (see “Wiring the Local Area Network [LAN]
Port”).
6. Plug an output device into the output power receptacle on the PC1 rear panel.
7. If desired, connect the output device to the serial COM port.
8. If desired, connect a contact closure device to the Input port.
9. If desired, connect an IR emitter to the IR port.
10. Press the front panel button to power on the receptacle.
11. Power on the output device.
12. Configure the PC1 interface using Global Configurator (provided on the included
software DVD) or the embedded web pages.
IPL T PC1 • Installation and Rear Panels
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panels
1
2
3
100-120VAC 50/60Hz
MAC ADDRESS
®
US
LISTED 17TT
AUDIO/VIDEO
APARATUS
COM
LAN
TX RX
INPUT
+5V
IR
4
IN
S
G
POWER OUTPUT 12A MAX
12A MAX
7
6
5
Figure 2. IPL T PC1 Rear Panel (120 VAC)
1
2
3
200-240VAC 50/60Hz
MAC ADDRESS
COM
LAN
TX RX
INPUT
+5V
IR
4
IN
S
G
POWER OUTPUT 10A MAX
10A MAX
7
6
5
Figure 3. IPL T PC1i Rear Panel (220 VAC)
a Power connector — Connect a power cord from a wall outlet to this male IEC power
receptacle.
b UID label — Contains the unique User ID number (MAC address) of the unit (for
example, 00-05-A6-00-00-01).
c COM port (RS-232) — Connect the output device serial port to this captive screw
connector to enable bidirectional RS-232 device control. This serial port contains the
following four pins, in order from left to right on the rear panel: transmission (Tx),
receiving (Rx), ground (_), and +5 V (to tie hand-shaking lines on the controlled device if
needed).
d LAN connector and LEDs — An Ethernet connection can be used on an ongoing basis
to monitor and control the PC1 and the device connected to it (see “Wiring the Local
Area Network (LAN) Port” for instructions on connecting the host to this port).
•
RJ-45 port — Plug a patch cable into this RJ-45 female socket,
and connect the other end to a network switch, hub, router, or
computer.
LAN
RJ-45
Port
•
•
Link LED — This green LED lights to indicate a good network
connection.
Link
LED
Activity
LED
Activity LED — This yellow LED blinks to indicate network
activity.
IPL T PC1 • Installation and Rear Panels
5
Download from Www.Somanuals.com. All Manuals Search And Download.
e IR port — Connect an IR emitter to pins 3 (S, for signal) and 4 (G, for ground) of this
shared captive screw connector to enable infrared remote control of the output device
The PC1 provides enough current to power one IR emitter up to 4000 feet, or a
maximum of four emitters in parallel up to 100 feet each. To enable IR control, load an
Extron IR driver to the PC1 for the output device, using Global Configurator, the PC1
web pages, or IR Learning.
f Input contact closure port — Connect a contact closure device to pins 1 (IN, for input)
and 2 (_, for ground) of this shared captive screw connector to enable the PC1 to detect
a closed circuit between an input and ground and to trigger an event (see “Wiring the
For example, if a button were pressed or motion were detected by a sensor, the input
would short to ground, which would cause an event such as a bell ringing, a light
turning on, or an e-mail notification that an event has occurred.
g Output power receptacle — Connect the power cord from an output device to this
female 3-prong Edison (IPL T PC1) or IEC (IPL T PC1i) power output receptacle.
Connecting Cables
Connect cables to the rear panel connectors as outlined below.
1. Plug an IEC power cord into a wall outlet and into the 3-prong male power connector
on the PC1 rear panel. The green Power LED lights and remain lit.
2. Plug the Ethernet cable from the network into the LAN port on the rear panel. The
green Link LED on the connector lights.
3. Plug the power cord of the output device to be controlled into the output receptacle on
the PCI rear panel.
4. If desired, connect the output device to the RS-232 COM port.
5. If desired, connect an IR emitter to the IR port to control an output device.
6. If desired, connect a contact switch to the contact input port.
The following sections provide details on wiring the appropriate cables to the rear panel
connectors.
RS-232 Port Cabling
To connect an output device, such as a plasma display or projector, to the PC1 RS-232
connector, see the “Extron IP Link Device Interface Communication Sheet” for your
display device. This sheet contains information about your device, including connector pin
assignments and connection diagrams, and is available from the Extron website.
Accessing the Communication Sheet
To obtain the Communication Sheet for your output device:
2. On the Download Center page, click the DeviceDriversbutton
(shown at right).
3. At the bottom of the Device Drivers page, select IPL T PC1 from the
drop-down menu.
4. On the next web page, select Serialfrom the Protocol Type drop-down menu to
display a list of the Extron serial drivers.
IPL T PC1 • Installation and Rear Panels
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. On the drivers list, locate the model name of your output device. In the row for your
device, click on the nnKblink in the Communication Sheet column.
In figure 4, below, the Communication sheet link for a 3M-7340 display has been
selected.
Figure 4. Communication Sheet Access
6. The communication sheet (a PDF file) opens. You can view, print, or download it.
7. Wire your display device as described in its communication sheet.
You can also access the Communication Sheets via the Global Configurator software (see
the IPL T PC1 Setup Guide for information on using GC3.2).
Connecting the Display Device
To connect the display device to the PC1:
1. Wire an RS-232 cable to the provided 4-pole captive screw connector, as described
below. Use only the first three pins of the connector, starting from the left.
a. Connect the wire from the Receive port of the display to the first pin (on the left) of
the connector, which plugs into the PC1 Tx (Transmit) port.
b. Connect the wire from the Transmit port of the display to the second pin of the
connector, which plugs into the PC1 Rx (Receive) port.
c. Connect the ground wire from the display to the third pin of the connector, which
plugs into the PC1 ground (_) port.
IPL T PC1
Rear Panel
RS-232 Port
RS-232
TxRx +5V
Ground (
)
Ground (
)
Receive (Rx)
Transmit (Tx)
Receive (Rx)
Transmit (Tx)
Bidirectional
Display
Device
Figure 5. Connecting an Output Device to the RS-232 Port
2. Plug the cable into the RS-232 receptacle on the PC1 rear panel.
NOTE: The RS-232 port is by default a control port. If you want to use it to
the “Front Panel Features and Operation” section).
IPL T PC1 • Installation and Rear Panels
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring the Local Area Network (LAN) Port
Wire the connector as shown in the tables below.
•
•
•
•
For 10Base-T (10 Mbps) networks, use a Category 3 or better cable.
For 100Base-T (100 Mbps) networks, use a Category 5 cable.
Use a straight-through cable to connect to a switch, hub, or router.
Use a crossover cable to connect directly to a computer.
Pins:
12345678
Crossover Cable
Straight-through Cable
End 1
End 2
End 1
End 2
Wire Color
Pin
Wire Color
Wire Color
Pin
Wire Color
1
White-orange
White-green
1
White-orange
White-orange
2
3
4
5
6
7
8
Orange
Green
2
3
4
5
6
7
8
Orange
White-green
Blue
Orange
White-green
Blue
White-orange
Blue
White-green
Blue
White-blue
Green
White-blue
Orange
White-blue
Green
White-blue
Green
White-brown
Brown
White-brown
Brown
White-brown
Brown
White-brown
Brown
Insert Twisted
Pair Wires
T568B
T568A
T568B
T568B
A cable that is wired as T568A at one end
and T568B at the other (Tx and Rx pairs
reversed) is a "crossover" cable.
RJ-45
Connector
A cable that is wired the same at both ends
is called a "straight-through" cable, because
no pin or pair assignments are swapped.
Figure 6. RJ-45 Connector Wiring
Wiring for IR Control
If you intend to control the display device via infrared (IR) commands from the PC1, wire
an Extron IR emitter to a 3.5 mm, 2-pole captive screw connector (provided), and plug the
2-pole connector into the IR Signal and Ground pins (pins 3 and 4) of the shared captive
screw connector on the rear panel.
Alternatively, you can wire the IR emitter to pins 3 and 4 of the provided 4-pole captive
screw plug (and, if desired, also wire a contact closure device to pins 1 and 2 of the same
4-pole connector into the rear panel Input/IR connector.
The PC1 provides enough current to power one IR Emitter up to 4000 feet, or up to four
emitters for 100 feet each (see figure 7, below).
IR
Emitter
White Striped Wire Only
E
D
Modulated IR
Ground
4000 feet (1574.8 m) Maximum
The PC1 can power a single IR Emitter
up to 4000 feet, or four emitters wired
in parallel up to 100 feet each.
IPL T PC1 Shared IR
and Input Connector
In S G
Figure 7. Wiring for IR Control via an IR Emitter
NOTE: Place the head of the IR emitter over or directly adjacent to the IR receiver of the
controlled device.
IPL T PC1 • Installation and Rear Panels
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring the Contact Input Port
The IPL T PC1 contact closure Input port can be connected to any device providing a closure
to ground (closed = logic 1 and open = logic 0). The contact input is connected to 5 VDC via
a 1k ohm pull-up resistor and must be wired with a ground. This allows the input to be tied
to a device such as a motion detector, alarm, photo eye, and so forth. You can define what
this input will trigger via GC3.3.
1. Connect one end of the input cable to a 3.5 mm, 2-pole captive screw connector
(provided), and plug the connector into the two Input pins (In and _) of the shared
Input/IR port connector on the rear panel.
INPUT IR
Alternatively, you can wire the contact closure device to pins
Momentary
Switch
1 and 2 (from the left) of the provided 4-pole captive screw
S
G
IN
plug (and, if desired, also wire an IR emitter to pins 3 and 4
on the previous page). Plug the wired 4-pole connector into
the rear panel Input/IR connector.
2. Connect the other end of the input cable to the contact
input device that will provide a triggering signal (see the
diagram at right).
IPL T PC1 • Installation and Rear Panels
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
Features and
Operation
This section contains a description of the IPL T PC1 and IPL T PC1i front panel features and
instructions for setting up the PC1 using the front panel. The following topics are discussed:
•
•
•
Front Panel Features
Front Panel Features
1
2
3
IPL T PC1
POWER
100
LINK
ACT
R
8
TX
RX
INPUT
IR
4
7
6
5
Figure 8. IPL T PC1 and IPL T PC1i Front Panel
a Power button — Press this button to switch power on and off to the output receptacle
on the rear panel.
b Tx and Rx LEDs — The Tx (transmit) LED lights when RS-232 data is being transmitted.
The Rx LED lights when RS-232 data is being received.
c Input LED — This green LED lights when the Input contact closure port is activated
(shorted).
d LAN status LEDs — These three LEDs show the status of the Ethernet connection as
follows:
•
100 — When lit, indicates a 100 Mbs connection speed. Otherwise, the connection
speed is 10 Mbs.
•
•
Link — Lights steadily while the interface has an active network connection.
Act (Activity) — Blinks while data is being sent or received.
e IR LED — This green LED lights when IR data is being transmitted.
f Receptacle power LED — This red LED lights while power is being supplied to the rear
panel receptacle and, therefore, to the attached output device.
IPL T PC1 • Front Panel Features and Operation
10
Download from Www.Somanuals.com. All Manuals Search And Download.
g Reset button (recessed) — Use the tip of a small Phillips screwdriver or an Extron
Tweeker (provided) to press this recessed button to reset the unit in one of five reset
this Reset button).
h Power LED — This green LED lights while the PC1 or PC1i interface is receiving power
and is running.
When the unit is being reset from the front panel, this LED blinks the appropriate
Setting Up the System Using the Front Panel
The following system setup procedures can be performed using the front panel, Global
Configurator, the embedded web pages, or SIS commands.
This section discusses the front panel procedures. For information on using the web to set
the IPL T PC1 Setup Guide.
NOTE: The PC1 takes approximately 2 minutes to store settings made via the front
panel, SIS commands, or the web pages into its memory. If you disconnect
power from the PC1 less than 2 minutes after entering a setting, your entry may
be lost.
Setting Up Power Control of the Output Device
To set up power control of the output device plugged into the PC1 output power receptacle:
1. On the PC1 front panel, press and release the receptacle
POWER
Power button.
I
Receptacle
The green receptacle Power LED at the right of the
button lights and remains lit while the receptacle is
powered on. It turns off when the receptacle is powered
off.
Power Button
Receptacle
Power LED
2. Power on the device, using its own power switch.
If power is removed from the PC1, the power state of the output receptacle is preserved
in flash memory; for example, if the receptacle was powered on when the PC1 was
disconnected, it is powered on when the PC1 receives power again. This enables the
receptacle configuration to be easily restored if a power loss occurs.
CAUTION: Some devices, such as projectors, need a cool-down period to power off
safely. Use RS-232 or IR commands to power these devices.
IPL T PC1 • Front Panel Features and Operation
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Security Lockout (Executive Mode)
When the PC1 is in front panel lock mode (executive mode), it does not accept commands
from the front panel. If any button is pressed while the unit is in executive mode, the Power
LED flashes three times, indicating that the input from the front panel is not being accepted.
To enter or exit executive mode, press and hold the receptacle Power button for 3 seconds.
The Power LED flashes three times to indicate that the executive mode has been switched.
NOTES: • If power to the PC1 is recycled while the unit is in executive mode, the PC1
remains in executive mode.
• The Reset button is always functional. It is recessed to avoid it being pressed
accidentally.
Resetting
Reset the unit by pressing the Reset button on the front panel. This button is recessed, and
can be accessed with an Extron Tweeker or other small Phillips screwdriver.
CAUTIONS: • Review the reset modes carefully. Use of the wrong reset mode may
cause unintended loss of flash memory programming or a unit reboot.
• The reset modes described on the following pages break all TCP/IP
connections by closing all sockets to the unit.
IPL
T
PC
1
PO
R
W
ER
I
TX
RX
INPU
IR
100
LINK
T
A
C
T
Recessed Reset Button
Use tip of Philips head
on Tweeker to activate.
Figure 9. Reset Button
NOTES: • If the Reset button is continually held in, the Power LED pulses (blinks) every
3 seconds, and with each pulse, the PC1 goes into a different reset mode. For
mode 5, the LED blinks three times, indicating that it is the last mode.
• The reset modes are separate functions, not a progression from mode 1 to
mode 5.
IPL T PC1 • Front Panel Features and Operation
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode 1
Activation
Result
Hold in the Reset button while applying power to the unit.
Returns the unit to the default base firmware that was shipped
with the PC1 from the factory. Event scripting does not start when
the unit is powered on in this mode.
Purpose and notes Use mode 1 to remove a version of firmware if incompatibility
issues arise. All user files and settings are maintained. User web
pages may not work correctly if you are using an earlier firmware
version.
NOTE: After a mode 1 reset, the factory-installed firmware version remains in effect
only until the unit is powered off. After a power cycle, the PC1 returns to the
firmware that was installed prior to the mode 1 reset.
Mode 2
Activation
To enter mode 2, you use both the PC1 front panel and your
computer, as follows:
1. On the computer, open a command interface, such as Extron
DataViewer or HyperTerminal.
2. Immediately press the Reset button momentarily (for less than
1 second).
NOTE: Nothing happens if the momentary press does
not occur within 1 second.
3. Within 2 seconds of the momentary press, press the <+>
key on the computer keyboard three times.
Result
The RS-232 port is converted to a host port, which allows the use
of SIS commands and host responses.
No LEDs blink to indicate the mode switch. If the switch to mode 2
is successful and serial port communication is enabled, the interface
screen displays one of the following copyright messages:
• (c)Copyright2011,ExtronElectronics,IPLTPC1,
Vn.nn,60-544-nn
• (c)Copyright 2011,ExtronElectronics,IPLTPC1i,
Vn.nn, 60-544-nn
Purpose and notes By default, the RS-232 port is a device control port. In mode 2, the
serial port is able to receive SIS commands.
NOTE: If you do not enter the three plus (+) signs within 2
seconds of the momentary press of the Reset button,
the RS-232 port reverts to a device control port.
IPL T PC1 • Front Panel Features and Operation
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode 3
Activation
Result
Hold the Reset button in until the Power LED blinks once
(approximately 3 seconds). Release it, then immediately press it
again momentarily (for less than 1 second).
NOTE: Nothing happens if the momentary press does not
occur within 1 second.
Turns events on or off, depending on their current state. During
resetting, the reset LED flashes two times if events are starting and
three times if events are stopping.
Purpose and notes This mode is used for troubleshooting.
Mode 4
Activation
Hold the Reset button in until the Power LED blinks twice
(approximately 6 seconds). Release it, then immediately press it
again momentarily (for less than 1 second). The Power LED blinks
four times in quick succession, confirming a mode 4 reset.
NOTE: Nothing happens if the momentary press does not
occur within 1 second.
Result:
Reset mode 4 does the following:
• Enables ARP program capability.
• Sets the IP address back to factory IP settings.
• Sets the subnet mask back to factory default.
• Sets the gateway address back to factory default.
• Sets port mapping back to factory default.
• Turns DHCP off.
• Turns events off.
Purpose and notes Mode 4 enables you to set IP address information using ARP and
the MAC address.
Mode 5
Activation:
Hold in the Reset button until the Power LED blinks three times
(approximately 9 seconds). Release it, then immediately press it
again momentarily (for less than 1 second). The power LED blinks
four times in quick succession, confirming a mode 5 reset.
NOTE: Nothing happens if the momentary press does not occur
within 1 second.
Result:
Performs a complete reset to factory defaults (except for the
firmware).
Purpose and notes Mode 5 is useful if you want to start over with control software
configuration and to replace events.
IPL T PC1 • Front Panel Features and Operation
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HTML
Configuration
and Control
This section describes the IPL T PC1 embedded web pages and provides instructions on
accessing and using them to configure the PC1. Topics include:
•
•
•
•
•
The IPL T PC1 must be configured before use in order for it to control other devices. In
addition to using the button on the PC1 front panel, you can configure and control the PC1
via any computer attached to a LAN.
•
The default PC1 embedded web pages provide a means of setting up, adjusting, and
controlling the interface via a web browser from any type of network-enabled computer.
•
An alternative way to control and configure the PC1 from your computer is by using
Simple Instruction Set (SIS) commands via Telnet. SIS commands are discussed in detail in
•
Global Configurator (GC 3.3) software enables you to configure and control the PC1 as
well as set up output device monitoring and scheduling (see the IPL T PC1 Setup Guide,
provided with your PC1, for information on setting up using GC 3.3).
Configuring the Hardware for Ethernet Control
To enable Ethernet control, both the computer and the PC1 must be configured correctly.
The PC must be network-capable with the proper protocols, and the PC1 must be set up
so it can be connected to a LAN (local area network). Please note that some settings can be
configured only via Internet protocol.
For your PC to communicate with the PC1 via Ethernet, it must be equipped with an
network interface card and an HTML browser. To allow your PC to work with Extron
Ethernet-controlled products, the TCP/IP protocol must be installed and properly configured.
IPL T PC1 • HTML Configuration and Control
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up and Configuring the PC1 Using ARP
The Address Resolution Protocol (ARP) command provides a quick way to set up an IP
address for the PC1, using your PC. The ARP commands tell your computer to associate the
PC1 Media Access Control (MAC) address with an IP address that you assign.
1. Obtain a valid IP address for your PC1 from your network administrator.
2. Obtain the PC1 MAC address (UID#) from the small label on the PC1 rear panel (see
have the following format:
00-05-A6-nn-nn-nn
3. If the PC1 has never been configured and is still set for factory defaults, skip to step 4. If
the “Front Panel Features and Operations” section for the resetting procedure.)
CAUTION: The PC1 must be configured with the factory default IP address
(192.168.254.254) before you execute the ARP command, as described
below.
4. On the computer, access the command prompt as follows:
a. From your Windows desktop Startmenu, select Run....
b. On the Run window, enter cmd. The command window opens.
5. At the command prompt enter arp -s, followed by the desired new IP address for the
PC1, a space, and finally the PC1 MAC address (taken from the small label on the rear
For example:
arp -s 10.13.197.57 00-05-A6-01-33-0D
A space must separate arpand the hyphen [-].
Figure 10. ARP-S Command Screen
6. Execute a ping command by entering ping, followed by the new IP address, at the
command prompt. For example:
ping 10.13.197.57
Ping is a utility or diagnostic tool that tests network connections. It is used to determine
if the host has an operating connection and is able to exchange information with
another host.
IPL T PC1 • HTML Configuration and Control
16
Download from Www.Somanuals.com. All Manuals Search And Download.
The response should be the new IP address of the PC1, as shown below.
Figure 11. Ping Command on a Command Prompt Screen
7. After verifying that the IP address change was successful, issue the arp -dcommand at
the DOS prompt to remove the address from the computer ARP table.
For example:
arp -d 10.13.197.57
A space must separate arpfrom the hyphen (-).
Setting Up and Configuring the PC1 Using a Web Browser
To set up the PC1 for Ethernet communication using a web browser, you must temporarily
configure the PC to communicate with the interface. Then you can change the default
settings of the PC1 (IP address, subnet mask, and [optionally] administrator name and
password) in order to use the unit on an intranet (LAN) or on the Internet (WAN). After you
have set up the PC1 for network communication, you can reset the computer to its original
network configuration.
IPL T PC1 LAN port defaults
192.168.254.254
0.0.0.0
PC1 IP address:
Gateway IP address:
Subnet mask:
255.255.0.0
Off
DHCP:
Auto detected
Link speed and duplex level:
If you use an existing Ethernet LAN intranet, your network administrator can provide you
with a unique IP address for the PC1 or confirm whether you need to set up the PC1 for
DHCP (Dynamic Host Configuration protocol) to have an address assigned automatically.
IPL T PC1 • HTML Configuration and Control
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Up the Computer for IP Communication
Follow these steps to set up communication between your computer and the PC1 using
Windows 2000, Windows XP, or Windows 7.
NOTE: The procedure and illustrations in this section are for Windows XP. For other
Windows versions, the screens may appear slightly different.
1. Open the Network Connections page as follows:
a. From the Startmenu, select MyNetworkPlaces.
b. From the NetworkTasksside-bar menu, select ViewNetworkconnections.
2. Right-click LocalAreaConnection, then select Properties.
Figure 12. Network Connections Window
IPL T PC1 • HTML Configuration and Control
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3. On the Local Area Connection Properties window, select
InternetProtocol(TCP/IP), then click the Propertiesbutton. If
InternetProtocol(TCP/IP)is not on the list, you must install it (see the Windows
user manual or the Windows online help system for the procedure).
Figure 13. Internet Protocol (TCP/IP) Selected on Local Area Connection
Properties Window
4. Write down the current IP address and subnet mask of your computer below. You will
need to restore these settings to the computer later.
If the ObtainanIPaddressautomaticallyradio button has been selected, make a
note of that.
5. On the Internet Protocol (TCP/IP) Properties window, change your computer IP address
temporarily so that it can communicate with the PC1:
a. Select the “UsethefollowingIPaddress” radio button.
b. Enter the following values as shown below:
192.168.254.253
255.255.0.0
IP address:
Subnet mask:
Default gateway:
Blank or0.0.0.0
(The temporary IP address differs from the PC1 factory default by 1 digit.)
IPL T PC1 • HTML Configuration and Control
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 14. Internet Protocol (TCP/IP) Properties Window for Windows XP
c. Click OKto save the changes and exit the network setup.
d. Reboot the computer if required for the changes to become effective.
6. Plug one end of a Category 5, 6, or 6E network crossover cable into the Ethernet (LAN)
in the “Installation and Rear Panel” section for information on wiring the RJ-45 LAN
connector). Plug the other end of the Ethernet cable into the Ethernet port on the
computer.
NOTE: If you are using a network hub or switch between the computer and the
PC1, use a straight-through Category 5 cable instead of a crossover cable.
below, for the procedure).
Once the PC1 has been reconfigured, you can subsequently use an Ethernet (intranet or
Internet) connection to configure or control it.
NOTE: Both your computer and the PC1 must be connected to the same LAN.
Configuring the IPL T PC1 Using a Web Browser
The default web pages that are preloaded on the PC1 are compatible with popular web
browsers such as Internet Explorer (version 5.5 or higher).
NOTE: The following instructions assume that you have configured the Windows-based
computer, connected it to the PC1 LAN port, and powered on the interface.
1. Obtain a valid IP address, subnet mask, and gateway address for the PC1 from your
network administrator.
2. Launch a web browser (such as Internet Explorer) on the connected computer (for which
you set up the network configuration earlier), and enter the default address of the PC1,
http://192.168.254.254, in the address box. The PC1 default web page is displayed.
IPL T PC1 • HTML Configuration and Control
20
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Select the Configurationtab, then select SystemSettingsfrom the sidebar menu
on the left of the screen. The PC1 System Settings page appears, showing the default IP
address.
Figure 15. System Settings Page with Default IP Address
4. Enter the new IP address assigned for the PC1, the corresponding subnet mask, and
gateway address, then click Submit.
IP, gateway, and subnet mask addresses follow standard naming and numbering
conventions and protocol (nnn.nnn.nnn.nnn). Your IP network administrator should
provide the addresses to be used with this interface.
The PC1 can takes up to 2 minutes to store the new settings. When the PC1 IP
address is changed, your computer loses communication with it, and a screen appears,
indicating that the page cannot be displayed.
5. Close the browser.
6. After changing the IP settings of the PC1, restore the original TCP/IP settings to your
computer and reboot it if necessary (see the addresses you wrote down in step 4 of the
You are now able to access the PC1 web pages to configure the front panel.
IPL T PC1 • HTML Configuration and Control
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the IPL T PC1 Web Pages
The IPL T PC1 features an embedded web server, which includes factory set web pages.
These pages can be replaced with user-designed files, but the default web pages provide
many basic features for configuring, and controlling the PC1 via a web browser. This section
provides an overview of the embedded web pages.
To access the embedded web pages:
1. Launch a web browser (for example, Internet Explorer) on your connected computer.
2. On the browser Address line, enter the PC1 IP address.
If you have previously created a Global Configurator 3 project for the PC1, the web
page opens in the GlobalViewer format. To display it in the default web page format,
enter the PC1 IP address, followed by /nortxe_index.html.
Example: 10.26.188.44/norte_index.html.
See the IPL T PC1 Setup Guide, delivered with your PC1, for information on using Global
Configurator.
NOTE: If a password has been set, the Enter Network Password dialog box opens. If
no password has been set, the PC1 web page opens, displaying the System
Status page. (Skip steps 3 and 4.)
3. Enter the administrator password in the Passwordfield. Leave the UserNamefield
blank.
Figure 16. Password Prompt Window
4. Click OK. The PC1 web page is displayed.
NOTES: • Passwords must contain 4 to 12 alphanumeric characters. Spaces and
non-alphanumeric symbols are not allowed, and the passwords are case
sensitive.
• Administrators have access to all of the web pages and are able to make
changes to settings. Users can access only the System Status page.
IPL T PC1 • HTML Configuration and Control
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Viewing the System Status
The System Status web page, accessed by clicking the Statustab, provides information
on the current settings. Changes must be made via the Configuration web pages or SIS
access can view this page but cannot access the Configuration or File Management pages.
Figure 17. System Status Screen
IPL T PC1 • HTML Configuration and Control
23
Download from Www.Somanuals.com. All Manuals Search And Download.
The System Status page displays information in the following categories:
•
•
•
System Description: Includes product model, port and receptacle description, part
number, firmware version, and the current date and time.
IP Settings: Displays the unit name, DHCP status, IP address, gateway address, subnet
mask, and the MAC address.
Port, AC, and Executive Mode Settings: Shows settings for the RS-232 and Contact
Input ports, name and On or Off status for the AC receptacle, and whether lock mode
(executive mode) is on or off.
•
Current Schedule: Shows the schedule currently in place for powering the output
device on and off, and for enabling and disabling executive mode.
Using the Configuration Pages
To access the Configuration pages, select the Configurationtab. There are seven web
pages that can be accessed from the Configuration page. They are listed in the sidebar
menu at the left of the page. These pages are described in the following sections.
Specifying system settings
On the System Settings page, you can set the date and time, change the IP address
information for the PC1, and enable or disable lock mode.
Figure 18. System Settings Screen on the Configuration Page
1. On the Configuration page, select SystemSettingsfrom the sidebar menu at the
left edge of the screen. The System Settings page appears, displaying either the factory
default information for your PC1 or the settings submitted most recently.
2. Enter your new information in the IP Settings section, or select the date and time from
the menus in the Date/Time Settings section, as described in the following sections.
IPL T PC1 • HTML Configuration and Control
24
Download from Www.Somanuals.com. All Manuals Search And Download.
IP settings
The following settings are available in the IP Settings section:
• UnitName: The default is the product name followed by the last six digits of
the MAC address. You can give the unit a new name (such as LightsOn&Offor
BoardroomA-PC1) consisting of up to 24 alphanumeric characters including the
hyphen (-).
NOTE: The first character must be an alpha character, and the last character cannot
be a hyphen. The unit name is not case sensitive.
• DHCP: DHCP is a communications protocol that assigns addresses on the local network
automatically. Select the Onor Offradio button to enable or disable DHCP.
NOTE: When DHCP is set to On, all other IP settings are disabled except Unit Name.
• IPAddress: You can enter a new network address, a 32-bit number consisting of four
sets of 8-bit numbers, separated by periods (nnn.nnn.nnn.nnn).
• GatewayIPAddress: A gateway is a device that connects your network with others
that may be outside your local area network. You can enter your gateway address
(obtained from your network administrator), using the same format that is used for the
IP address. (If there is no gateway, this field defaults to 0.0.0.0.)
• Subnetmask: The subnet mask is used to split IP networks into a series of subgroups
(subnets). The mask is a binary pattern that is matched up with the IP address to turn
part of the host ID address field into a field for subnets. You can enter a new subnet
mask address using the same format that is used for the IP address.
To change the IP address settings:
1. In the IP Settings section, make entries or selections in the available fields as desired.
2. When finished making entries in this section, click Submitto implement them.
If you want to discard your entries without submitting them, click Cancelto restore the
previous values (do not click Submit).
Date and time settings
The following settings are available in the Date/Time Settings section:
NOTE: This section lets you set the date and time on your PC1 unit. However, the
passage of time is not reflected in the Dateand Timefields on the web page.
The page continues to display the settings you entered and does not increment
them as time passes. However, the PC1 itself continues to keep the correct time
internally.
To display the current time on the screen, click Refreshon your web browser screen.
• Date: Select month, day, and year from the pull-down menus.
• Time: Select hours, minutes, and am or pm from the menus.
• Zone: From the pull-down menu, select the time zone for the location of the PC1
(number of hours offset from Greenwich mean time).
IPL T PC1 • HTML Configuration and Control
25
Download from Www.Somanuals.com. All Manuals Search And Download.
• DaylightSavings: Daylight savings time (DST) is a one-hour offset that is observed
in some countries. You can select one of the radio buttons to set the PC1 for daylight
savings time for the U. S., Europe, or Brazil; or select Offto disable it.
The following daylight savings periods are observed:
•
U. S. — Starts the second Sunday in March and ends the first Sunday in November.
(Daylight saving time should be turned off in Hawaii, American Samoa, most
equatorial regions, Guam, Puerto Rico, the U. S. Virgin Islands, eastern time zone
portion of the state of Indiana, and the state of Arizona (excluding the Navajo
Nation).
•
•
Europe — Starts the last Sunday in March and ends the last Sunday in October.
(Daylight saving time should be turned off in Iceland.)
Brazil — Starts the first Sunday in October and ends the third Sunday in February.
(Daylight saving time should be turned off in equatorial Brazil.)
3. When you have made all the desired changes in the Date/Time Settings section, click
the Submitbutton at the bottom of the section. The new date and time settings are
displayed in the fields in which you entered them.
If you want to discard your new entries without submitting them and restore the
previous settings, click Cancel(do not click Submit).
Configuring the RS-232 Port and the AC Receptacle
The Port & AC Settings screen, accessed from the Configuration screen, enables you to
specify settings for the RS-232 port and the rear panel AC receptacle.
Figure 19. Port & AC Settings Page
Contact input port
This field shows the status of the contact input port. If Onis selected, the contact is closed
(connected to ground). If Offis selected, the contact is open (not connected to ground).
NOTE: You cannot make changes in this field; it only reflects the condition of the port.
IPL T PC1 • HTML Configuration and Control
26
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 port
From the drop-boxes in the port type section, you can select the baud rate, data bits, parity,
stop bits, and flow control for the PC1 serial COM port.
Click Submitto enter your selections.
If you click Cancelbefore submitting your selections, your entries are reset to the last saved
parameters.
Defaults are:
9600
8
Baud Rate:
Data Bits:
Parity:
None
1
Stop Bits:
Flow control:
None
AC receptacle
In the AC Receptacle Settings section, you can do the following:
•
Enter a name for the receptacle, which could reflect the output device connected to
it, the room in which the device is located, and so forth. The name can be 1 to 12
characters. The following characters are not permitted:
# % + = ~ ` : ; “ ‘ , . | \
By default, the receptacle is named Receptacle 1.
Select the Onor Offradio button to power the connected device on or off.
•
Click Submitto implement your changes. If you click Cancelbefore submitting your
selections, your entries are reset to the last saved parameters.
Using the IR Drivers page
The IR Drivers page lets you view the IR drivers that have been uploaded to the PC1 via the
the commands contained within the IR driver, and cause the connected output device to
perform (“play”) any of the listed commands.
For an IR driver to appear on this page, you must rename its file to a number with an
.eir extension (for example, 1.eir, 2.eir, and so forth) before uploading it via File
Management. When the driver is displayed on the IR Drivers page, its device name also is
displayed.
Figure 20. IR Drivers Page
IPL T PC1 • HTML Configuration and Control
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Performing a command
To play a command on the connected device:
1. Click on the driver file in the Driver (first) column to display a list of commands within
the selected driver. The example below shows part of a driver command list page for a
Sony SLV-D360P DVD/VCR combination.
Figure 21. Example of a Driver Command List Page
2. Click on a command name. The connected device performs the selected function.
Assigning passwords
The Passwords screen allows you to assign passwords to the administrator and user access
levels.
The administrator password gives access to all IPL T PC1 web pages, enabling the
administrator to configure the PC1.
The user password provides access only to the System Status web page. If you are logged
in as user, you see only the Statustab with the System Status page. You cannot make any
configuration changes.
To assign passwords:
1. On the Configuration page, select Passwordsfrom the sidebar menu.
2. Enter the new administrator password in the AdministratorPasswordfield.
Passwords must contain 4 to 12 alphanumeric characters.
Spaces and non-alphanumeric symbols are not allowed, and the passwords are case
sensitive.
IPL T PC1 • HTML Configuration and Control
28
Download from Www.Somanuals.com. All Manuals Search And Download.
3. In the Re-enterAdminPasswordfield, enter the same password again to confirm it.
Figure 22. Passwords Page with Administrator and User Passwords Entered
4. If you want to assign a user password, enter it in the UserPasswordfield.
NOTE: You cannot assign a user password unless an administrator password has
either been assigned or is being assigned at the same time.
5. Reenter the same user password in the Re-enterUserPasswordfield.
6. Click Submitto set the passwords.
Removing passwords
To remove a password:
1. On the Configuration page, select Passwordsfrom the sidebar menu.
2. In the AdministratorPasswordor the UserPasswordfield, delete the characters
that are there, and press the <Spacebar> to enter a space.
3. In the Re-enterAdminPassword, the Re-enterUserPassword, or both fields, delete
the characters that are there, and press the <Spacebar> to enter a space.
4. Click Submit.
NOTE: Deleting the administrator password also deletes the user password.
IPL T PC1 • HTML Configuration and Control
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Entering e-mail addresses
If you have created scheduled events or monitoring tasks through the Global Configurator
software, you may have e-mail alerts with a message corresponding to an event or task (for
example, a timer notification indicating that it is time to replace a projector light bulb). The
PC1 web pages allow you to conveniently make changes to your alerted e-mail addresses
and to change your message file.
Initial setup and settings changes must be made in the Global Configurator software.
The e-mail alert can notify up to 49 recipients at one time; the Email Alerts page lets you
enter up to 49 e-mail addresses.
Figure 23. E-mail Alerts Page (Upper Portion)
1. On the sidebar menu on the Configuration page, click EmailAlerts.
2. On the Email Alerts page, click the Editbutton located to the right of the MailIP
Addressfield. The page goes into Edit mode, and the Editbutton changes to Save.
3. Enter your mail server IP address and your domain name in the appropriate fields. (This
information is available from your network administrator.)
4. Click Saveto save the information.
IPL T PC1 • HTML Configuration and Control
30
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click the Editbutton at the end of the first address row in which you want to enter
a new address or edit the existing one. The Editbutton changes to Save(see the
illustration above).
6. Enter the e-mail address of the alert recipient in the numbered box under Email
Address.
7. In the File Name column, enter the name (seven characters maximum) of the file
containing the alert message. The message file name must have the extension .eml.
NOTE: Due to the seven-character limit for full file names, it is recommended
that you use numeric file names (for example, 1.eml, 24.eml, and so on).
Numeric titles reduce the characters in the file name and assist in keeping
the alert files organized. However, alphabetic titles are permitted.
8. Click the Savebutton beside the file name that you entered. The e-mail alert
information is saved on the PC1, and the Savebutton becomes Editagain.
9. Repeat steps 5 through 8 for each e-mail recipient address that you want to add or edit.
Setting up SMTP authentication
On the Email Alerts page, you can also specify that SMTP (Simple Mail Transfer Protocol)
authentication is needed for the PC1 to send mail to the e-mail server.
To set the PC1 to require SMTP authentication before the server accepts any e-mail:
1. To enable the SMTP authentication fields, click the Editbutton at the right of the Mail
IPAddressfield. The Editbutton changes to Save.
2. Select the SMTPAuthenticationRequiredcheck box, located below the Domain
Namefield. This enables the UserNameand Passwordfields below the check box.
3. In the UserNameand Passwordfields, enter a user name and a password that senders
must enter in order for the mail server to authenticate the sender.
For the user name, you can use any combination of letters, numerals, spaces, and
symbols except the comma (,) and the single and double quotation marks (‘and “).
For the password, you can use all characters except the comma. The user name and
password can each be from 1 to 30 characters.
NOTE: You must specify both a user name and a password.
4. Click the Savebutton next to the MailIPAddressfield to save your user name and
password.
To remove SMTP authentication requirement, click Edit, deselect the SMTP
AuthenticationRequiredcheck box, then click Save.
IPL T PC1 • HTML Configuration and Control
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Upgrading Firmware
The Firmware Upgrade page lets you browse to locate and upload a new version of firmware
for your unit. The uploaded file must have the file extension .S19.
NOTE: The PC1 uses the same firmware as the IPL T PC1. However, it does not accept
other firmware files, such as the .s19 files for the IP Link S Series.
To find out the version of firmware that is currently loaded on your PC1, see “Firmware:” in
Downloading the firmware from the web
To obtain the firmware file to load to your PC1:
2. Click the Downloadtab.
3. On the Download Center page, click the Firmwarelink at the top of the left sidebar
menu.
4. On the Archives line at the top of the Firmware page, click the letter I.
5. On the next page that appears, click the Downloadlink at the right end of the IPL T PC1
or IPL T PC1i line.
6. Fill in the required information on the next Download Center page, and click the
DownloadIPLTPC1button.
7. Click Runon the FileDownloadwindow.
8. Follow the instructions on the installation wizard screens. The new firmware file is
placed on your computer internal disk.
Updating the firmware
To upload a new version of firmware:
1. On the sidebar menu of the Configuration page, click FirmwareUpgrade. The Firmware
Upgrade page is displayed, showing the version of firmware that is currently loaded.
Figure 24. Firmware Upgrade Page
IPL T PC1 • HTML Configuration and Control
32
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Click Browseto open a Choose file window.
Figure 25. Firmware File Selected on the Choose File Window
3. In the Choose file window, locate the new firmware version file on your computer and
double-click it. (Firmware files must have the extension .S19.) By default, this file is
placed at:
c: \Program Files\Extron\Firmware\IPL_T_PC1\pcsVx.xx.S19
The firmware file name and path are displayed in the CurrentFirmwareVersionfield
on the Firmware Upgrade screen.
4. Click Upload. When the firmware upgrade is complete, the Power LED on the unit
blinks three times.
NOTES: • If you attempt to upload a file with an extension other than .S19, the PC1
recognizes it as invalid and ignores it, reverting to the last successfully
uploaded firmware version.
• The new firmware version number does not immediately appear on the
Firmware Upgrade screen. To verify that the new version was uploaded,
click the Status tab to view the System Status screen. When you return to
the Firmware Upgrade screen, the new version number is displayed there
also.
IPL T PC1 • HTML Configuration and Control
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Scheduling
The Schedule page accessed from the Configuration screen lets you schedule when power
to the receptacle turns on and off. You can also schedule lock mode, specifying when the
PC1 front panel will be locked. Clicking the ClearSchedulebutton at the bottom of the
screen deletes all schedules. You may want to set up your schedule for a week at a time, or
a day at a time.
To access the Schedule page, click Scheduleon the sidebar menu on the Configuration
page.
Figure 26. Schedule Page
On the Schedule page:
•
When you click on a day, On, Off, or the contents of any cell in the Current Schedule
table (a time or a dash [-]), a Set Schedule For section displays above the Scheduling
section. In this field you enter your settings for power or executive mode.
•
•
To close the Set Schedule For section without saving your entries in it, click Refreshat
the bottom of the screen.
If you want to clear all power and executive mode settings from the schedule, click
ClearSchedule, at the bottom of the screen.
IPL T PC1 • HTML Configuration and Control
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Scheduling output receptacle power
To schedule power on and off to the output receptacle:
1. In the Receptacle 1 section, click Onor Offto select the power setting that you want
to schedule for the week. A Set Schedule For section appears above the Scheduling
section, displaying the receptacle number (always 1, for PC1/PC1i), the power selection
you clicked (Onor Off), and menus from which to select the hour, minutes, and am/pm.
The illustration below shows the Set Schedule For section, with PowerOnscheduled for
6:00 am Monday through Friday.
Figure 27. “Set Schedule For” Section, Displayed for Receptacle 1
2. From the drop-down menus, select the time (hour, minutes, and am or pm) at which
you want power turned on or off.
3. Select the check boxes for the days of the week you want the receptacle to be turned
on or off at the time you specified.
4. When finished, click Setto save your settings and close the Set Schedule For section.
The settings you entered appear in the Current Schedule in the Receptacle 1 section.
5. Repeat steps 1 through 4 for any additional power settings you want to make.
IPL T PC1 • HTML Configuration and Control
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Scheduling front panel lockout (executive mode)
1. In the Executive Mode section, click Onor Offto select the lock mode setting that you
want to schedule. A Set Schedule For section appears above the Scheduling section,
displaying the current status of Executive Mode (Onor Off); menus from which to select
the hour, minutes, and am or pm; and check boxes for the days of the week.
The illustration below shows the Set Schedule For section, with executive mode
scheduled to be disabled at 6:00 am Monday through Friday. (In the Executive Mode
section in the example below, front panel lockout has been scheduled to start at
7:30 pm, Monday through Friday.)
Figure 28. “Set Schedule For” Field for Executive Mode
2. From the drop-down menus, select the time (hour, minutes, and am or pm) at which
you want executive mode enabled or disabled.
3. Select the check boxes for the days of the week you want lock mode to be turned on or
off at the time you specified.
4. When finished, click Setto save your settings and close the Set Schedule For section.
The settings you entered appear on the Current Schedule in the Executive Mode section.
5. Repeat steps 1 through 4 as needed to specify lock mode settings for other days.
NOTE: You cannot set Receptacle On and Off for the same time.
IPL T PC1 • HTML Configuration and Control
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Scheduling by day of the week
You can also select a day of the week and schedule all power and executive mode time
settings for that day at one time:
1. Click on a day of the week at the top of a column in the Receptacle 1 scheduling table.
Two Set Schedule For sections open, one for Power On and Executive Mode On and one
for Power Off and Executive Mode Off. These sections contain drop-down menus for
selecting on and off times as well as check boxes for selecting the receptacle (power)
and executive mode.
In the illustration below, Sundayhas been selected for scheduling.
Figure 29. Schedule Screen Showing Fields for Daily Receptacle Scheduling
2. In either the Power ON or Power OFF section, select the hours, minutes, and am or pm
from the menus; and select the check boxes for the items you want to schedule.
3. In the section in which you made your selections, click Setto enter your choices. The
section closes.
4. If desired, repeat steps 2 and 3 in the other Set Schedule For section.
If you do not want to make selections in the remaining Set Schedule For section, click
Refreshto close the section.
5. Repeat steps 1 through 4 for any additional days that you want to schedule.
IPL T PC1 • HTML Configuration and Control
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing an individual setting
Follow this procedure if you want to change only one setting on the scheduling table, either
for powering on or off, or for executive mode.
1. In the Receptacle or Executive Mode scheduling table, click on the time displayed or the
“-” symbol in the cell that you want to change, in the desired day column. A single-line
Set Schedule For section appears above the Scheduling section.
In the following illustration, the red circle indicates the cell that was selected: receptacle
powering off, on Monday.
Figure 30. Set Schedule For Field to Set Powering Off for a Single Receptacle
2. From the drop-down menus in the Set Schedule For section, select the hour, minutes,
and am or pm for the power or lock mode setting.
3. Click Setto enter your settings. The time that you entered appears in the cell that you
selected on the Scheduling table.
Managing Files
The File Management screen allows you to upload and delete files, including IR drivers,
from your computer or server. File names must contain valid alphanumeric characters or
underscores; spaces and special characters (symbols) are not allowed. Only personnel with
administrator access can view the File Management page and make changes.
Uploading files to the web page
The IPL T PC1 has approximately 7.25 MB of space for IR drivers, custom web pages, and
other user files to be uploaded. The Bytes Left field shows how much user space remains for
uploading files.
To upload files:
1. Select the File Management tab on the IPL T PC1 web page.
2. On the File Management page, click Browseto open a Choose file window.
3. On the Choose file window, locate and select a file to upload. (Only one file at a time
can be selected.) The file name and directory path appear in the Browsefield on the File
IPL T PC1 • HTML Configuration and Control
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 31. File Management Screen with Three Files Uploaded
4. Click Upload File. While the file is uploading, the UploadFilebutton label changes
to Uploading....
When the uploading is complete, the uploaded file name appears in the Files column with
a time stamp showing GMT time, and the button returns to its original state. (Files are listed
separately under headings of their extensions.)
Adding a directory
To add a directory or folder to the IPL T PC1 file system:
1. Enter a name for the directory in the Dir:field, following the slash (/).
2. Click AddDir.
the previous section to add a file to the directory. The directory name appears at the top
of the Files column, preceded by a slash.
NOTE: If no files are added to the new directory, it is deleted when you open
another directory.
To add more files to the directory, click the directory name to open it, then use the
Uploading files procedure. To exit the directory, click on (root)in the Files column.
Other file management functions
On the File Management page, you can also do the following:
•
•
•
Open and view an uploaded file by clicking on its name.
Delete an uploaded file by clicking on the Deletebutton beside it.
Delete all uploaded files and directories by clicking the DeleteAllbutton.
IPL T PC1 • HTML Configuration and Control
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Web Pages
On the IPL T PC1, custom web pages are supported. You can determine the layout and
appearance of the pages displayed on your screen. Server side includes (SSIs) enable you to
obtain information from the unit and display the information on web pages. Query strings
allow you to send information and commands to the unit to change its configuration or
Server Side Includes (SSIs)
Server side includes are a type of HTML comment that directs the web server to dynamically
generate data for a web page whenever it is requested. SSIs typically use SIS commands to
communicate with the products or attached control devices. Using SSIs, you can design and
display custom pages, with PC1 information provided by the SIS commands (see the “SIS
Programming and Control” section for these commands).
The basic format for an Extron SSI is <!—#echo var=”x”—>, where xis the SIS command to
be executed.
When a web page is requested, the web server removes the SSI and replaces it with the
answer to the SIS command within quotes.
Server Side Include Using
the Host SIS command
SIS Command
<!--#echo var="
N
"-->
SIS command
to be processed
by the IP Link
*type with no spaces
Figure 32. Example of the SSI Command
In the figure above, the Ncommand is used to request the PC1 part number.
Query strings
A query string is the portion of a URL that appears after the question mark. The query string
contains parameters or instructions for the web server to execute. The basic format for a
query string within a link is:
<a href=”index.html?cmd=x”>Receptacle 1</a>
where xis the SIS command to be executed.
When a link is accessed on a web page, the URL is passed to the web server to tell it which
web page to return to the browser. The portion of the URL after the question mark is the
query string, which contains the SIS command that the IPL T PC1 will remove and execute.
Like SSI formatted commands, query strings can use any valid SIS command.
The query string in the figure below turns off DHCP on the IP Link device.
SIS Command*
?
">
<a href="index.html
Receptacle on </a>
cmd=
W1*1PC|
Starts
query string.
SIS Command
To Be Processed
by the IP Link
Closes
link.
HTML Code
for a Link
HTML Code
for a Link
Linked Text
Tells web server
that SIS
command follows.
*Enter with no spaces.
Figure 33. Example of a URL with a Query String Using an SIS Command
IPL T PC1 • HTML Configuration and Control
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Code example
The following figure shows a practical use for both SSIs and query strings. In this example,
the HTML source code contains three SSI commands.
<html>
<head><title>Example 1</title></head>
<h2 b>HTML Example #1</h2 b>
<body>
The following lines demonstrate how to read status from the IPLink Product:
IPLink Product Name: <b><!--#echo var="1I"--></b>
<br>
SSI
commands
IPLink Product Description: <b><!--#echo var="2I"--></b>
<br>
IPLink Product Part Number: <b><!--#echo var="N"--></b>
</body>
</html>
Figure 34. Web Page HTML Source Code Document Showing SSIs
The SSI commands in the figure above request the product name, product description, and
product part number of an IP Link device.
The figure below shows the HTML code that results from the SSIs shown in the above
example.
<html>
<head><title>Example 1</title></head>
<h2 b>HTML Example #1</h2 b>
<body>
The following lines demonstrate how to read status from the IPLink Product:
IPLink Product Name: <b>IPL T PC1</b>
<br>
IPLink Product Description: <b>One Switched 110v AC Receptacle with
Serial and IR communication</b>
<br>
IPLink Product Part Number: <b>60-544-10</b>
</body>
</html>
Figure 35. Resulting HTML Source Code Served by an IP Link web Server
Notice, in the figure below, that the commands executed by the PC1 in response to SSI
references have been replied to, and were implemented when the web page was served to
the browser.
Figure 36. Browser View of Previous HTML Source Code
IPL T PC1 • HTML Configuration and Control
41
Download from Www.Somanuals.com. All Manuals Search And Download.
URL encoding
URL (Universal Resource Locator) encoding is the method of using ASCII hexadecimal
characters to display specific characters in a URL. It is used for several reasons. On some
operating systems, certain characters are unsafe or not available, and others are reserved by
the HTML or URL specification. URL encoding is used to insure compatibility and functionality
with most Internet browsers. As a general rule, use the hexadecimal encoding method
shown below when these characters appear in your URLs.
The following types of characters do not require encoding in a URL:
Alphanumeric characters 0-9, a-z, A-Z
Special characters
$ _ - . + ! * ( ) ,
; / ? : @ = &
Reserved characters
NOTE: When used for their reserved purposes, these
characters do not require encoding within a URL.
Figure 37. Characters that Do Not Require Encoding
Reserved characters
Reserved characters should not be encoded when they appear in their conventional meaning
in a URL. For example, do not encode the slash (/) when using it as part of the URL syntax.
Only encode unsafe characters (defined in the table in the next section) in your URLs.
The following table lists reserved characters.
Character
Hexadecimal Decimal
$
&
+
,
/
:
=
?
@
Dollar
24
26
2B
2C
2F
3B
3D
3F
40
36
38
43
44
47
59
61
63
64
Ampersand
Plus
Comma
Forward slash or virgule
Colon
Equal
Question mark
“At” symbol
IPL T PC1 • HTML Configuration and Control
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Unsafe characters
URLs use some characters for “special use” in defining their syntax and these characters
should be encoded. For various reasons, these characters may possibly be misunderstood
within a URL.
The following table lists unsafe characters.
Character
Space
“” Quotation marks
Hexadecimal Decimal
20
22
3C
3E
23
25
7B
7D
7C
5C
5E
7E
5B
5D
60
32
34
<
>
#
%
{
}
|
\
^
~
[
]
`
“Less than” symbol
“Greater than” symbol
Pound
60
62
35
Percent
37
Left brace
123
125
124
92
Right brace
Vertical bar or pipe
Back slash
Caret
94
Tilde
126
91
Left bracket
Right bracket
Grave accent
93
96
Accessing and Using Telnet (Port 23)
Telnet, short for Telecommunications Network, provides a way for you to connect to a
computer or server (in this case, the PC1 interface) on a network. Once connected via
Telnet, you can send ASCII serial commands (see the Command and Response Table for SIS
Commands in the “SIS Programming and Control” section to configure and monitor the
PC1 settings).
1. From your desktop Startmenu, select Run, then enter Telnet, then click OK. The
Telnet program starts (see the figure below).
Figure 38. Telnet Command Prompt
2. At the command prompt, enter open.
IPL T PC1 • HTML Configuration and Control
43
Download from Www.Somanuals.com. All Manuals Search And Download.
3. At the to prompt, enter the IP address of the PC1 unit. (The default IP address is
< >
192.168.254.254. If the address was changed in the setup or configuration process, use
the new address.) Telnet defaults to port 23.
Figure 39. Connecting to the IP Address
4. If passwords were set up for the connected system, you are prompted to log in as an
administrator or a user. Otherwise, the system responds with a carriage return and line
feed (<CR/LF).
5. Once you are connected, you can enter SIS commands as desired; for example, 1*1PC
for more information on entering SIS commands.
6. When you are finished entering commands to the interface, enter Ctrl+]at the
command prompt to exit Telnet.
IPL T PC1 • HTML Configuration and Control
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Turn on the equipment in the following order:
1. The PC1 power control interface
2. The power receptacles on the PC1
3. The connected output device on the AC receptacle.
If the output AV device cannot be powered on, check the following:
Power Connections
POWER
1. Make sure that the output receptacle is receiving power.
The green Power LED on receptacle remains lit steadily
while the receptacle has power. If necessary, press the
receptacle Power button to apply power.
I
Receptacle
Power Button
2. Ensure that the device is plugged in properly to the rear
panel of the PC1 and switched on if applicable.
Receptacle
Power LED
Network Connections
1. Check the network connections and make adjustments as needed. The green Link
LED lights steadily while a network connection is detected. The yellow ACT LED blinks
if there is activity on the network. If these LEDs are not lit, either the cable is faulty
or not plugged in, or the wrong type of cable is being used (see “Connecting the
Hardware,” in the “Installation and Rear Panel” section).
2. At the DOS command prompt, try to ping the unit by entering pingand the IP address
PC1 is connected and communicating, you receive the following response to your ping
command:
Figure 40. Successful Ping Command Response
IPL T PC1 • HTML Configuration and Control
45
Download from Www.Somanuals.com. All Manuals Search And Download.
If a connection was not made, the following response appears:
Figure 41. Response to an Unsuccessful Ping Command
If you get a response indicating that the ping was unsuccessful:
a. Make sure your unit is using the appropriate subnet mask (check with your system
administrator).
b. Make sure your PC does not have a software firewall program which might block
the IP address of the unit.
3. If contact is established with the unit, but the unit web pages cannot be accessed
by your web browser, verify (in the Optionsor Preferencesmenu) that your web
browser is configured for direct network connection and not set up to use a proxy
server.
If you are still experiencing problems, call the Extron S3 Sales & Technical Support Hotline.
Global Configurator Software
The Global Configurator 3 (GC 3.3) software is an alternative to using the default web
pages to configure and schedule the PC1. GC 3.3 is a free asset management software that
enables flexible, centralized, web-based power management for A/V systems. Using Global
Configurator software, administrators can view the immediate status and power level of an
output device, schedule actions such as powering on and off, monitor specified conditions,
and configure its ports.
To download the latest version of Global Configurator 3 from the Extron website:
1. Select the Downloadtab on the Extron website home page.
2. From the sidebar menu at the left of the screen, select Software.
3. On the Download Center page, click the Downloadlink at the right end of the Global
Configurator line.
4. Fill in the required information on the next Download Center page, and click the
Download GCSWnnn.exebutton (where nnnis the GC3 version number).
5. Click Runon the File Download window.
6. Follow the instructions on the subsequent screens to install GC3.3 on your computer.
For instructions on using the GC3.3 software with the PC1, see the IPL T PC1 Setup Guide,
provided with the PC1, and to the Global Configuration 3.3 help program, accessible from
the GC3.3 main screen.
NOTE: GC 2.3 is the minimum version required to configure the PC1.
IPL T PC1 • HTML Configuration and Control
46
Download from Www.Somanuals.com. All Manuals Search And Download.
SIS Programming
and Control
This section provides instructions on using the Extron Simple Instruction Set (SIS) commands,
which you can use to set up and control the IPL T PC1 from a host computer or other control
system attached to the rear panel LAN port. The following topics are discussed:
•
•
•
•
As shipped, the PC1 works as a standalone interface, but cannot control any other devices
until it is configured. You can set up and control the PC1 by using the front panel, the web
pages, Global Configurator, or SIS commands. Both the web pages and the SIS methods are
accessed via Ethernet LAN connection. The LAN port defaults are:
192.168.254.254
0.0.0.0
IPL T PC1 IP address:
Gateway IP address:
Subnet mask:
255.255.0.0
Off
DHCP:
Host-to-Interface Communication
SIS commands consist of one or more characters per field. No special characters are required
to begin or end a command sequence. When the PC1 determines that a command is valid,
it executes the command and sends a response to the host device. All responses from the
]
interface to the host end with a carriage return and a line feed (CR/LF = ), which signals
the end of the response character string. (A string is one or more characters.)
Messages Initiated by the IPL T PC1
When a local event such as a front panel selection or adjustment takes place, the PC1
responds by sending a message to the host. No response is required from the host. The
following PC1-initiated messages are sent (underlined):
©Copyright2011,ExtronElectronics,IPLTPC1[i],Vn.nn,60-544-nn]
Www,DDMmm2011HH:MM:SS]
The PC1 sends the boot and copyright messages when it first powers on and is connected
via Telnet or TCP/IP. Vn.nnis the firmware version number; 60-544-nnis the product part
number. The current date and time are displayed. If you are using a Telnet connection, the
copyright message, date, and time are followed by a password prompt.
IPL T PC1 • SIS Programming and Control
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Password Information
The ]Password:prompt is displayed only if there is a password defined in the unit. It
requires a password (administrator level or user level) followed by a carriage return. The
prompt is repeated if the correct password is not entered.
If the correct password is entered, the unit responds with ]LoginAdministrator]or
]LoginUser], depending on the password entered. If the passwords are the same for
both administrator and user, the unit defaults to administrator privileges.
Error Responses
When the PC1 receives a valid SIS command, it executes the command and sends a response
to the host device. If the PC1 is unable to execute the command because the command is
invalid or it contains invalid parameters, it returns an error response to the host.
The error response codes and their descriptions are as follows:
E12– Invalid port number
E13– Invalid value (the number is out of range/too large)
E14– Not valid for this configuration
E17– System timed out
E22– Busy
E24– Privilege violation
E25– Device is not present
E26– Maximum number of connections has been exceeded
E27– Invalid event number
E28– Bad filename or file not found
E30– Hardware failure (followed by a colon [:] and a descriptor number)
E31– Attempt to break port pass-through when it was not set
Error Response References
The following superscripted numbers are used within the command descriptions in the
Command and Response table to identify commands that may respond as shown:
14
commands that give an E14(invalid command for this configuration) response if
sent to an IPL product whose power configuration does not support the command.
=
24
commands that give an E24(privilege violation) response if you are not logged in at
the administrator level.
=
27
commands that may yield an E27(invalid event number) response.
=
28
commands that may give an E28(file not found) response.
=
IPL T PC1 • SIS Programming and Control
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Command and Response Table
The PC1 can be controlled via either a Telnet (port 23) connection or a web browser
(port 80) connection. The ASCII commands listed in the tables perform the same functions,
but they are encoded differently to accommodate the requirements of each port (Telnet or
web browser). The ASCII to hexadecimal (HEX) conversion table below is for use with the
command and response tables.
ASCII to Hex Conversion Table
Space
•
Figure 42. ASCII to Hex Conversion Table
The command and response table lists valid ASCII (for Telnet) command codes, the
corresponding URL (universal resource locator) encoded (for web browsers) command codes,
the interface responses to the host, and a description of the command function or the
results of executing the command.
•
Upper- and lowercase characters can be used interchangeably in the command field
unless otherwise specified.
•
•
•
Commands may be sent back-to-back without spaces (for example, 2!65V1Z).
Numbers can be entered as 1, 2, or 3 digits (for example, 8V= 08V= 008V).
There are a few differences in how to enter the commands, depending on whether you
are using Telnet or a web browser.
•
When using these commands through a web browser, you can use the URL
reference to shorten the examples. “URL” refers to the full address of the
control interface and web page reference, including all path information (that is,
•
•
To send any of the commands using a web browser you must prefix them with the
full URL followed by ?cmd=.
For control via a web browser, all non-alphanumeric characters must be represented
as the hexadecimal equivalent, %xx, where xxrepresents the two-character hex
byte. For example, a comma (,) would be represented as %2C. Characters such
as %, +, and the space character must be encoded as hex bytes, or they will be
misinterpreted by the interface.
•
Some characters differ depending on the method you use to send the commands:
Telnet
Web Browser
Escape (hex 1B)
Carriage return (hex 0D)
W(must not be hex encoded)
Pipe character (|) (must not be hex encoded)
NOTES: • With Telnet you can use either an Escapecommand or a W
command, and the carriage return or the pipe character. With the
web browser, you must use a Wcommand and the pipe character.
• In either method, Data= Data that will be directed to a specified
port and must be hex encoded if non-alphanumeric.
IPL T PC1 • SIS Programming and Control
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Symbol Definitions
=
CR/LF (carriage return + line feed) (hex 0D0A)
]
=
Soft carriage return (no line feed, hex 0D)
}
(For web browser commands, use the |[pipe] character instead of the soft return.)
=
=
Pipe (vertical bar) character
Space
|
•
24
The 24 superscript indicates commands that give an E24(privilege violation) message if you are not logged in at the
=
administrator level.
=
=
=
Escape key (hex 1B) (For web browsers, use Winstead of E. )
Power receptacle (1-4)
E
X!
Greenwich Mean Time (GMT) offset value
X#
(-12.00 to +14.00) represents the time difference in hours and minutes ( hh:mm) relative to Greenwich, England. The
plus sign and leading zero are optional. For example, 5:30 = +05:30.)
=
=
=
On or Off status
X%
X^
X(
0= off or disable
1= on or enable
Dirty memory status
1= RAM needs to be saved to flash memory.
0= RAM has been saved to flash (OK to power off or reset).
Current threshold sense
0= clear or none
1= standby
2= full
(Full threshold must be set before standby.)
=
Group number
X1)
0= none
1= yellow
2= green
3= red
(The exponent designates the port number. The color relates to setting groups via the front panel.)
=
=
Version (typically listed to two decimal places, that is, n.nn)
X1!
X1@
Unit name. The name of the PC1 is a text string of up to 24 characters drawn from the alphabet (A-Z), digits (0-9),
and minus sign or hyphen (-). No blank or space characters are permitted as part of a name. No distinction is made
between upper and lower case.
NOTE:
The first character must be a letter. The last character must not be a minus sign or hyphen.
=
Local date and time format
X1#
Set format (MM/DD/YY-HH:MM:SS).
Example: 11/18/03-10:54:00.
Read format (day of week, day month year HH:MM:SS).
Example: Tue,18Nov201118:19:33.
=
X1$
IP address (nnn.nnn.nnn.nnn). Leading zeros in each of four fields are optional in setting values, and they are
suppressed in returned values.
=
=
E-mail domain name (for example: extron.com)
X1%
X1^
Power-up delay between ports in 1/3-second increments. 1-255permitted.
(Default is 3, which equals 1 second.)
IPL T PC1 • SIS Programming and Control
50
Download from Www.Somanuals.com. All Manuals Search And Download.
=
Time in tens of milliseconds to wait for the first character to arrive at a serial port before terminating (default=1=10
ms; max = 32767) the connection
X1&
=
=
Hardware (MAC) address (xx-xx-xx-xx-xx-xx).
X1*
X1(
Subnet mask (nnn.nnn.nnn.nnn). Leading zeros are optional in setting values in each of four fields, and they are
suppressed in returned values.
=
=
Time in tens of milliseconds to wait between character arriving at a serial port before terminating (default=2=20 ms;
max = 32767) the connection
X2)
X2!
Parameter to set either Length of the message to receive or the Delimiter value.
•
•
If the message is length delimited, use nnL, where nnis the length of the incoming message in bytes.
If the message is character delimited, use xxD, where xxis the decimal ASCII value of the delimiting character.
For verbose response mode:
X2@
0= clear or none
1= verbose mode
2= tagged responses for queries
3= verbose mode and tagged responses for queries
Default = 0
NOTE:
If tagged responses are enabled, all read commands return the constant string plus the data, like setting
the value does.
Example:
Command:
Response:
ECN}
Ipn• X1@
=
Priority status for receive timeout:
X2#
0= priority set to SendDataStringcommand parameters
1= priority set to ConfigureReceiveTimeoutcommand parameters
=
=
Baud rate: 300, 600, 1200, 1800, 2400, 3600, 4800, 7200, 9600, 14400, 19200, 28800, 38400, 57600, or
115200
X2%
X2^
Parity (Only the first letter is needed.)
O= Odd
E= Even
N= None
M= Mark
S= Space
=
=
=
Data bits: 7or 8
X2&
X2*
X3)
Stop bits: 1or 2
Flow control (Only the first letter is needed.)
S= Software
N= None
=
=
Password (minimum length = 4 characters; maximum length = 12 characters.
No special characters are allowed.
X3#
X3$
Daylight saving time (DST) is a 1-hour offset to reflect the time during which clocks are set one hour or more ahead of
local standard time, to provide more daylight at the end of the working day. Supported for the U. S. and parts of Brazil
and Europe.
Example: Time in California is GMT -8:00 from March to November and GMT -7:00 from November to March. DST
should be turned off in Hawaii, American Samoa, Guam, Puerto Rico, the Virgin Islands, the eastern time zone portion
of the state of Indiana, and the state of Arizona (excluding the Navajo Nation).
0= off or ignore
1= U. S.
2= Europe
3= Brazil
IPL T PC1 • SIS Programming and Control
51
Download from Www.Somanuals.com. All Manuals Search And Download.
=
=
Event number: range = 0-99
X3%
X3^
Event buffer
0= receive
1= user (absolute)
2= User (relative)
3= NVRAM
=
=
X3&
X3*
Memory location: range = 0through maximumbuffersize
Event data size
b= bit
B= byte (8 bits)
S= short (16 bits)
L= long (32 bits)
NOTE:
This parameter is case sensitive.
=
=
Event data to write
X3(
X4!
Reading password. Responds with four asterisks (****) in place of the password, if a password exists. Responds with
an empty space if no password exists.
=
Contact input setting
X4@
0= off (open)
1= on (closed)
=
=
=
=
Number of bytes to read: range = 1-127
X4$
X4%
X4^
X4&
E-mail event number (1-64)
E-mail recipient address (for example, JDoe@extron.com) for the person to whom messages will be sent.
For the CRcommand: Name (numeral) of e-mail file to be sent; for example: 1.eml, 2.eml, ... 64.eml. The first
line of the file is the subject; the rest is the message body.
For the SMcommand: Numeric name for the e-mail file to be sent. The file must be named n.eml (ncan be 0-999);
for example, 1.eml, 2.eml, ... 999.eml.
This command overrides the file specified in the CR command. If the value is 0 or a parameter is missing, the file
specified for the mailbox in the CR command is sent instead.
X4&
file is not found.
NOTE:
The SMcommand sends a default e-mail message if the
=
=
Default name: a combination of the model name and the last three pairs of the interface MAC address
(for example: IPL-T-PC1-00-02-3D).
X4(
X5@
Connection security level
11= user
12= administrator
=
ASCII digits representing the numeric value of the data element read from the event buffer (leading zeros are
suppressed).
X5$
=
=
IR file number: 0-99. The response is returned with leading zeros.
X5&
X5*
IR function number
0= return all data
1-127= functions that can be played or can return information (text). The response is returned with leading zeros.
129= manufacturer
130= model
131= class
132= remote
133= creation date
134= comments
137= user file name (descriptive name given to the file by the user)
NOTE: 0and numbers greater than 127can return information only.
IPL T PC1 • SIS Programming and Control
52
Download from Www.Somanuals.com. All Manuals Search And Download.
=
IR Playback mode
X5(
0= play once
1= play continuously
Response is returned with leading zeros.
To stop mode 1 playback, send the IR command again with mode 0selected.
Time in seconds to keep sending the broadcast message (0-255, default = 10)
=
=
X6$
X6(
(Ethernet only) Number of seconds before timeout on IP connections (min. = 1, max. = 6500, and
default = 30= 300 seconds).
If no data is received during the timeout period, the Ethernet connection is closed. Each step is 10seconds. The
response is returned with leading zeros.
=
The number (as an optional parameter) that is inserted into the e-mail message if the .eml file has an embedded
command (with no parameters).
X7)
=
=
Hardware (MAC) address: the four most significant hex nibbles converted into a single 16-bit decimal number.
Hardware (MAC) address: the eight least significant hex nibbles converted into a single 32-bit decimal number.
X7!
X7@
NOTE: This can be up to 10 digits.
=
=
=
E-mail account user name. Maximum length is 31 characters. This parameter is optional; commas cannot be used as
X7#
X7$
X71!
placeholders for it. If it is omitted from an issued command, any existing user account name is cleared.
E-mail account password. Maximum length is 31 characters. This parameter is optional; commas cannot be used as
placeholders for it. If it is omitted from an issued command, any existing user account password is cleared.
Days of the week
1= Sunday
2= Monday
3= Tuesday
4= Wednesday
5= Thursday
6= Friday
7= Saturday
=
=
Time in minutes (0-1440)
X71@
X71#
0= 12 am (midnight)
1440= clear schedule
Example: 1439= 11:59
Use the following formula (in 24-hour time format): (hour x 60) + minutes = time in minutes
Power receptacle name (12 characters maximum)
IPL T PC1 • SIS Programming and Control
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Command and Response Table for SIS Commands
ASCII (Telnet)
(Host to Switcher)
URL Encoded (web)
(Host to Switcher)
Response
(Switcher to Host)
Command
Power Receptacle Control / Current Sense
Turn receptacle power on
Turn receptacle power off
View receptacle power status
E
E
E
}
}
|
|
•
]
]
1*1PC
1*0PC
W1%2A1PC
W1%2A0PC
Cpn01 Ppc1
•
Cpn01 Ppc0
}
|
X% ]
1PC
W1PC
1X
]
Exe1
Exe0]
Set Executive mode on
Set Executive mode off
View Executive mode
1X
0X
X
0X
X
X% ]
Power Receptacle Naming
Set receptacle name24
Set receptacle name to factory
default24
Nmo1,
Nmo1,
X71#]
X71#]
E X71# }
X71# |
NO
|
W1%2C%20NO
1,
NO
W1%2C
E
}
1, NO
•
X71#]
View receptacle name
E
}
|
W1NO
1NO
Power Receptacle Scheduling
Set scheduling24
E X71! X% X71@ }
1* * * SS
X71!
X71!
X71!
X71!
X%
%2A %2A
X71@
W1%2A
W1%2A
W2%2A
W2%2A
SS
X71! X% X71@ ]
Set1* * *
X71@]
View scheduling
E X71! X% }
1* * SS
X% |
%2A SS
Front Panel Lockout Scheduling (Executive Mode)
Set scheduling24
E X71! X% X71@ }
2* * * SS
X%
%2A %2A
X71@
SS
X71! X% X71@ ]
Set2* * *
X71@]
View scheduling
E X71! X% }
2* * SS
X% |
%2A SS
Ethernet Data Port Commands
Set current connected port
timeout
E X6( }
0* TC
X6( |
TC
X6( ]
W0%2A
Pti0*
View current connected port
timeout
E
}
|
X6( ]
0TC
W0TC
X6(
Set global IP port timeout
Pti1*
E X6( }
1* TC
X6( |
TC
W1%2A
View global IP port timeout
E
}
|
W1TC
X6( ]
1TC
Information Requests
NOTE:
An asterisk (*) after a version number indicates the version that is currently running. Question marks (?.??)
indicate that only the factory firmware version is loaded. A caret (^) indicates the firmware version that should be
running; however, a mode 1 reset was executed and the factory default firmware version is currently loaded. An
exclamation point (!) indicates corrupted firmware.
Query firmware version
Q
Q
X1! ]
With tagged response –
verbose modes 2 and 3:
X1!]
Ver01*
Query verbose version information 0Q
0Q
Sumofresponsesfrom
]
2Q, 3Q, and4Q
With tagged response –
verbose modes 2 and 3:
X1!
Ver00* sumof
responsesfrom2Q,
]
3Q,and4Q
Query firmware information
1Q
1Q
X1! ]
With tagged response –
verbose modes 2 and 3:
X1!]
Ver01*
IPL T PC1 • SIS Programming and Control
54
Download from Www.Somanuals.com. All Manuals Search And Download.
ASCII (Telnet)
(Host to Switcher)
URL Encoded (web)
(Host to Switcher)
Response
(Switcher to Host)
Command
Information requests (continued)
Query bootstrap version
2Q
2Q
3Q
X1! ]
With tagged response –
verbose modes 2 and 3:
Ver02*
X1!]
Query factory firmware version
3Q
X1!
plus (webversion–
model– UL– dateand
]
time)
With tagged response –
verbose modes 2 and 3:
X1!
Ver03*
plus (web
version– model– UL–
]
dateand time)
Query updated firmware version
4Q
4Q
X1!
plus (webversion–
model– UL– dateand
]
time)
With tagged response –
verbose modes 2 and 3:
X1!
Ver04*
plus (web
version– model– UL–
]
dateand time)
60-544-10or
Request interface part number
N
N
]
60-544-20
With tagged response –
verbose modes 2 and 3:
Pno60-544-10 or
]
60-544-20
Request model name
1I
1I
IPLTPC1or
]
IPLTPC1i
With tagged response –
verbose modes 2 and 3:
]
inf01*IPLTPC1
Request model description
2I
2I
2I
2I
Briefproduct
]
description
Example
One220VACSwitched
ACReceptacle,
OneBi-Directional
SerialPort
[RS-232],
OneIRPort,One
]
ContactInputPort
With tagged response –
verbose modes 2 and 3:
inf02*brief product
]
description
IPL T PC1 • SIS Programming and Control
55
Download from Www.Somanuals.com. All Manuals Search And Download.
ASCII (Telnet)
(Host to Switcher)
URL Encoded (web)
(Host to Switcher)
Response
(Switcher to Host)
Command
Information requests (continued)
Request system memory usage
3I
3I
Numberofbytesused
outofthenumberof
]
totalkbytes
With tagged response –
verbose modes 2 and 3:
inf03*Numberof
bytes used out of
]
numberofkbytes
Request user memory usage
4I
4I
Numberofbytesused
outofthenumberof
]
totalkbytes
With tagged response –
verbose modes 2 and 3:
inf04*Number of
bytes used out of
]
number of kbytes
E-mail Commands
Configure e-mail events
(mailbox)24
E X4% X4^ X4& }
, , CR
X4%
X4^
%2C
X4& |
X4% X4^ X4& ]
CR Ipr , ,
W
%2C
Example:
E
}
5,jdoe@extron.com,7.emlCR
W5%2Cjdoe%40extron%2Ecom%2C7%2EemlCR|
Ipr5,jdoe@extron.com,7.eml
X4^ X4& ]
]
View e-mail events (mailbox)
E X4% }
CR
E X4% }
X4% |
CR
W
W
,
Send e-mail events (file named in
X4% |
X4^ ]
SM
SM
Eml
mailbox)24
Send e-mail using a different file24
E X4% X7) X4& }
X4%
X7)
X4& |
SM Eml
X4^ ]
, , SM
W
%2C
%2C
Web Browser-specific Commands
Read response from last URL cmd
E }
UB
|
WUB
Responsefrom
]
command
Mail Server Setup Commands
Set mail server IP, unit domain
E X1$ X1% X7# X7$ }
, , , CM
X1$
X1%
X7# X7$ |
%2C CM
W
%2C
%2C
name, and SMTP authentication24
X1$ X1% X7# X7$ ]
Ipm• , , ,
View mail server IP, unit domain
name, and SMTP authentication24
Set mail server IP and unit domain
name24
E }
CM
|
X1$ X1% X7# X7$ ]
, , ,
WCM
E X1$ X1% }
, CM
X1$
X1% |
CM
X1$ X1% ]
Ipm• ,
W
%2C
View mail server IP and unit
domain name
E }
CM
|
X1$ X1% ]
WCM
,
IP Setup Commands
Set the unit name24
Set unit name to factory default24
E X1@ }
CN
X1@ |
CN
|
W%20CN
X1@ ]
X4( ]
W
Ipn•
Ipn•
E
}
•CN
View unit name
Set date and time24
E }
|
WCN
X1@ ]
CN
E X1# }
X1# |
CT
X1# ]
CT
W
Ipt•
Example:
]
11/16/11-10:54:00
X1# ]
View date and time
E }
CT
|
WCT
Example:
Tues,16NOV2011
]
10:10:54:00
IPL T PC1 • SIS Programming and Control
56
Download from Www.Somanuals.com. All Manuals Search And Download.
ASCII (Telnet)
(Host to Switcher)
URL Encoded (web)
(Host to Switcher)
Response
(Switcher to Host)
Command
IP Setup Commands (continued)
Set GMT offset24
E X# }
CZ
X# |
W CZ
X# ]
Ipz
View GMT offset
E }
|
WCZ
X# ]
CZ
Set daylight savings time24
View daylight savings time
Set DHCP on24
E X3$ }
X3$ |
CX
X3$ ]
Ipx
CX
W
E }
CX
|
X3$ ]
Idh1
Idh0
WCX
E
E
]
|
|
]
]
1DH
0DH
W1DH
W0DH
Set DHCP off24
]
NOTE:
Changing DHCP from On to Off resets the IP address to the factory default (192.168.254.254).
View DHCP mode
E ]
DH
E X1$ }
CI
E }
CI
E }
CH
|
X% ]
Ipi•
X1$ ]
X1* ]
WDH
W
WCI
WCH
Set IP address24
X1$ |
CI
X1$ ]
View IP address
View hardware (MAC) address
|
|
With tagged response –
verbose modes 2 and 3:
X1* ]
X1( ]
Iph•
Ips•
X1( ]
Set subnet mask24
View subnet mask
Set gateway IP address24
View gateway IP address
Set verbose mode24
E X1( }
CS
E }
CS
E X1$ }
CG
E }
CG
X1( |
CS
W
|
WCS
X1$ |
CG
X1$ ]
W
Ipg•
X1$ ]
X2@ ]
Vrb
|
WCG
E X2@ }
CV
X2@ |
CV
W
NOTE:
The IPL T PC1 can send out unsolicited information (such as notice of a power level change). This is called a
verbose (wordy) relationship between the interface and a connected device. When the IPL T PC1 is connected to
the computer via Ethernet, verbose mode is disabled (by default) in order to reduce the amount of communication
traffic on the network. If you want to use the verbose mode with the PC1 connected via Ethernet, you must set
verbose mode to On each time you reconnect the computer to the network.
View verbose mode status
E }
CV
|
X2@ ]
WCV
Set broadcast mode
Set broadcast mode to default
address
E X6$ X1$ }
, EB
E X6$ }
EB
X6$
X1$ |
EB
W
W
%2C
EB
Bmd
Bmd ,
X6$ |
X6$ X1$ ]
Clear broadcast mode
E
}
|
X1$ ]
Bmd000,
0EB
W0EB
View broadcast mode
Set broadcast port and MAC
address
E }
|
X6$ X1$ ]
EB
WEB
X7! X7@ }
,
E
portnumber*
* PB
X7! X7@ |
* PB
Wportnumber*
WPB|
X1* ]
Bptportnumber*
View broadcast port and MAC
address
E }
PB
X1* ]
portnumber*
X7! X7@
is the MAC address for UDP unicast transmissions.
NOTE: Portnumberis the UDP outgoing port.
Get connection listing
*
E }
CC
|
WCC
Numberof
]
connections
With tagged response –
verbose modes 2 and 3:
IccNumberof
]
connections
IPL T PC1 • SIS Programming and Control
57
Download from Www.Somanuals.com. All Manuals Search And Download.
ASCII (Telnet)
(Host to Switcher)
URL Encoded (web)
(Host to Switcher)
Response
(Switcher to Host)
Command
Password and Security Settings
Set administrator password24
Clear administrator password24
E X3# }
CA
X3# |
X4! ]
W
CA
Ipa•
E• }
CA
]
Ipa•
|
W%20CA
NOTE:
A user password cannot be assigned if an administrator password does not exist. If the administrator password is
cleared (removed), the user password is also removed.
View administrator password24
Set user password14, 24
Clear user password24
E }
CA
|
X4! ]
X4! ]
WCA
E X3# }
X3# |
CU
W
CU
Ipu•
E• }
|
]
CU
W%20CU
Ipu•
X4! ]
X5@ ]
View user password24
E }
CU
E }
CK
|
WCU
Query session security level
|
WCK
With tagged response –
verbose modes 2 and 3:
X5@ ]
Pvl
]
NOTES: • The Passwordprompt requires a password (administrator level or user level), followed by a carriage return.
The password prompt appears only if there is a password defined on the unit.
•
The copyright information displayed upon connection to the IP Link product via TCP/IP or Telnet is followed by
the password prompt.
]
•
•
The Passwordprompt is repeated if a correct administrator or user password is not entered.
]
]
If a correct administrator or user password is entered, the unit responds with LoginAdministrator or
LoginUser , depending on the password that was entered. If the administrator and user passwords are
the same, it defaults to administrator privileges.
]
]
Remapping Port Designations
NOTE:
Duplicate port number assignments are not permitted; that is, Telnet and web cannot be the same. Entering
duplicate port assignments results in an E13(invalid parameter) error message.
Set Telnet port map24
Reset Telnet port map24
Disable Telnet port map24
View Telnet port map
Set web port map24
E
E
E
}
|
]
]
portnumberMT
WportnumberMT
Pmtportnumber
}
|
]
]
23MT
W23MT
Pmt00023
Pmt00000
}
|
0MT
W0MT
E }
|
]
MT
WMT
portnumber
E
}
|
portnumberMH
WportnumberMH
Pmhportnumber
Reset web port map24
Disable web port map24
View web port map
Set Direct Access port map24
Disable Direct Access port map24
View Direct Access port map
E
E
}
|
]
]
80MH
W80MH
Pmh00080
Pmh00000
}
|
0MH
W0MH
E }
MH
|
]
]
WMH
portnumber
E
E
}
]
2001MD
W2001MK|
Pmd02001
}
|
|
0MD
WMD
W0MD
portnumber
WMD|
E MD}
NOTE:
Remapping a port number (other than to reset it to the default 80or 23, or to disable it by setting it to 0) must be
to port number 1024or higher.
IPL T PC1 • SIS Programming and Control
58
Download from Www.Somanuals.com. All Manuals Search And Download.
ASCII (Telnet)
(Host to Switcher)
URL Encoded (web)
(Host to Switcher)
Response
(Switcher to Host)
Command
Directory Commands
Change or create a directory
E
}
path/directory/CJ
|
Wpath/directory/CJ
•
]
]
Dir path/directory/
NOTE:
A directory does not truly exist until a file has been copied into the path.
• ]
Dir /
Move back to root directory
Move up one directory
E
E
}
|
/CJ
W%2FCJ
}
..CJ
|
W%2E%2ECJ
•
Dir path/directory/
]
path/directory/
View current directory
E }
|
WCJ
CJ
File Commands
Erase user-supplied web page or
•
]
E
}
|
WfilenameEF
Del filename
filenameEF
file24, 28
]
Ddl
Erase current directory and its
E
}
|
/EF
W%2FEF
|
W%2F%2FEF
files24, 28
Erase current directory and its
subdirectories24, 28
List files from current directory
]
E
E
}
Ddl
//EF
}
|
DF
WDF
(See below.)
Telnet text responses:
•
•
]
]
]
filenamex date/time length
•
•
filenamex date/time length
•
•
filenamex date/time length
...
•
]
space_remaining BytesLeft
]
Web responses — HTML sample code:
Var file – new Array ();
File [1] = ‘filename1, date1, filesize1’;
File [2] = ‘filename2, date2, filesize2’;
...
File [n] = ‘filenamen, daten, filesizen’;
File [n+1] = ‘spaceremaining,Bytesleft’
IPL T PC1 • SIS Programming and Control
59
Download from Www.Somanuals.com. All Manuals Search And Download.
ASCII (Telnet)
(Host to Switcher)
URL Encoded (web)
(Host to Switcher)
Response
(Switcher to Host)
Command
File Commands (continued)
List files from current directory
and below
E
}
|
WLF
LF
(See below.)
Telnet text responses:
•
•
•
•
path/directory/filenamex date/time
]
]
]
length
length
length
•
path/directory/filenamex date/time
•
path/directory/filenamex date/time
...
•
]
space_remaining BytesLeft
web responses — HTML sample code:
Var file – new Array ();
File [1] = ‘filename1, date1, filesize1’;
File [2] = ‘filename2, date2, filesize2’;
...
File [n] = ‘filenamen, daten, filesizen’;
File [n+1] = ‘spaceremaining,Bytesleft’
NOTE:
The response to this command is the same as for the “List files from current directory” command (DF), except that
path/directoryprecedes filenames for files from subdirectories below the current directory.
Stream Files via Port 80
Load file to user flash memory24,28
Use a POSTon port 80 followed by the delimited data to be written to the flash
file memory.
Retrieve files from user flash
memory24 28
|
Send a page GETon port 80 followed by WSF
Rawunprocesseddata
infile
http://192.168.254.254/mypage.html?cmd=WSF
Example:
Stream Files via Telnet
Load file to user flash memory24,28
E
E
}
+UFfilesize,filename
Rawunprocesseddatainfileuptofilesize
]
Upl
Retrieve file from user flash
memory24 28
}
filenameSF
1BfilenameSF0D
Four bytes of filesize
+ rawunprocessed
data infile
Event Control
Read event buffer memory27
E X3%,X3^,X3& X3* E}
X3*
WX3% %2CX3^ %2CX3& X3* E}
X5$ ]
Write event buffer memory24,27
E X3%,X3^,X3&,X3(
E}
X3(
WX3% %2CX3^ %2CX3& %2C
X3* E}
X3% X3^ X3& X3( ]
Evt , , ,
X3& X3%
X3%
X3&
NOTE:
The response to the WriteEventcommand is padded with leading zeros for
and
X4$
.
is 5 digits and
is 10 digits.
Read string from event buffer
memory27
E X3%,X3^,X3&,X4$ FE}
WX3% %2CX3^ %2CX3& %2C
FE}
]
string
IPL T PC1 • SIS Programming and Control
60
Download from Www.Somanuals.com. All Manuals Search And Download.
ASCII (Telnet)
(Host to Switcher)
URL Encoded (web)
(Host to Switcher)
Response
(Switcher to Host)
Command
Event Control (continued)
Write string to event buffer
E string*X3%,X3^,X3& FE}
memory24,27
X3&
WX3( %2AX3% %2CX3^ %2C
FE}
X3% X3^ X3&
]
Evt , , ,string
NOTES: • Fmust be capitalized in order for strings to be read and written to event buffer memory.
X3%
X3& X3%
is 5 digits and
•
•
The response to the WriteEventcommand is padded with leading zeros for
X3&
and
.
is 10 digits.
The WriteStringcommand requires a string beginning with
E
. Strings returned by the device (read or write
E
response) are binary data (without an
).
Start events24,27
Stop events24,27
Ego
Est
]
E
E
}
}
|
|
1AE
0AE
W1AE
W0AE
]
]
Query number of events running
nnnnn
(5-digit number)
E }
AE
|
WAE
With tagged response –
verbose modes 2 and 3:
]
Enmnnnnn
(5-digit number)
Reset (Zap) and Erase Commands
NOTE:
None of the following zap commands (ZFFF, ZXXX, ZY, or ZQQQ) reset the AC power receptacle. Power remains
in its current state.
]
]
Erase all files from user flash
memory24
Reset all device settings to factory
default24
Zpf
Zpx
E
E
}
}
|
|
ZFFF
ZXXX
WZFFF
WZXXX
NOTE:
This reset is product-dependent. It resets receptacle name and lock mode to Off. It does not reset IP settings such as
IP address, subnet mask, gateway IP address, and IP security level table; and it does not remove the user file system.
]
Absolute system reset; retain IP
address
Zpy
E }
ZY
|
WZY
NOTE:
This reset is the same as ZQQQ(below), except that it excludes IP settings such as IP address, subnet mask, gateway
IP address, unit name, DHCP, and port mapping (Telnet, web, and Direct Access) in order to preserve communication
with the device. It also erases the user file system. This reset is recommended to be used after a firmware update.
Absolute system reset24
Zpq
]
E
}
|
WZQQQ
ZQQQ
NOTE:
This is a mode 5 reset (see “Resetting” in the “Front Panel Features and Operation” section). It resets all device
settings to the factory defaults; however, the firmware version remains the same.
IPL T PC1 • SIS Programming and Control
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Material
Specifications
AC control interface
Connectors
IPL T PC1 ................................. 1 female USA/Edison power connector
IPL T PC1i ................................ 1 female IEC power connector
Voltage
IPL T PC1 ................................. 120 VAC, 50-60 Hz
IPL T PC1i ................................ 220 VAC, 50-60 Hz
Maximum AC load
IPL T PC1 ................................. 12 A, 1440 watts at 120 VAC
IPL T PC1i ................................ 10 A, 2200 watts at 220 VAC
Serial control interface
Serial control port........................... (1) RS-232 only, 3.5 mm captive screw connector, 4 pole
Baud rate and protocol................... 115200 to 300 baud (9600 baud = default) ; 8 (default) or 7 data bits; 1(default)
or 2 stop bits; no parity (default), or even or odd parity
Serial control pin configuration....... 1 = Tx, 2 = Rx, 3 = GND, 4 = +5 VDC
Ethernet control interface
Connector...................................... 1 female RJ-45 connector
Data rate........................................ 10/100Base-T, half/full duplex with autodetect
Protocols........................................ ARP, ICMP (ping), IP, TCP, UDP, DHCP, HTTP, SMTP, Telnet
Default settings.............................. Link speed and duplex level = autodetected
IP address = 192.168.254.254
Subnet mask = 255.255.0.0
Gateway = 0.0.0.0
DHCP = off
Web server..................................... Up to 200 simultaneous sessions
7.25 MB nonvolatile user memory
Program control ............................. Extron Simple Instruction Set(SIS™)
Global Viewer requirements ........... Microsoft® Internet Explorer ver. 6 or higher
Contact closure interface— input only
Quantity/type ................................. 1 contact closure input
Contact input control connector..... (1) 3.5 mm captive screw connector, 4 pole (shared with IR output port)
Contact closure (input only)
Input voltage range ................. 0 to 5 VDC, clamped at +5.1 V
Input impedance...................... 10k ohms
Threshold................................. 1.6 VDC
Pin configuration............................ 1 = contact input, 2 = GND
IPL T PC1 • SIS Programming and Control
62
Download from Www.Somanuals.com. All Manuals Search And Download.
IR control interface
IR control port................................ (1) 3.5 mm captive screw connector, 4 pole (shared with contact closure input
port)
Pin configuration............................ 3 = S (IR signal output), 4 = GND
IR output carrier frequency............. 30 kHz to 1 MHz
General
Power input ................................... Internal
100-240 VAC, 50-60 Hz
5 watts
IPL T PC1 ................................. 12 A (max.)
IPL T PC1i ................................ 10 A (max.)
Temperature/humidity .................... Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing
Cooling.......................................... Convection, no vents
Mounting
Rack mount............................. Yes, with optional 1U rack shelf
Furniture mount ...................... Yes, with optional under desk mounting kit
Enclosure type................................ Metal
Enclosure dimensions ..................... 1.7" H x 4.3" W x 6.0" D (1U high, quarter rack wide)
(4.3 cm H x 10.9 cm W x 15.2 cm D)
(Depth excludes connectors.)
Product weight............................... 1.0 lbs (0.5 kg)
Shipping weight............................. 3 lbs (2 kg)
Vibration........................................ ISTA 1A in carton (International Safe Transit Association)
Regulatory compliance
Safety
IPL T PC1............................ CE, c-UL, UL
IPL T PC1i........................... CE
EMI/EMC ................................. CE, C-tick, FCC Class A, ICES, VCCI
MTBF ............................................. 30,000 hours
Warranty........................................ 3 years parts and labor
NOTES: • All nominal levels are at 10%.
• Specifications are subject to change without notice.
IPL T PC1 • SIS Programming and Control
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Numbers and Accessories
Included Parts
These items are included in each order for an IPL T PC1 or IPL T PC1i interface:
Included Parts
Part Number
60-544-10
IPL T PC1
IPL T PC1i
60-544-20
Rubber feet (self-adhesive) (4)
2-pin female captive screw terminal (2)
4-pin female captive screw terminal (1)
18 AWG IEC power cord (U. S. shipments only)
Tweeker (small screwdriver)
IPL T PC1 Setup Guide
IPL T PC1 Software CD-ROM
Optional Accessories
These items are optional for the IPL T PC1 and the IPL T PCli:
Optional Accessories
Part Number
60-190-01
60-604-02
60-190-10
60-604-11
70-077-01
RSU 129 Universal Rack Shelf Kit (9.5 inches deep)
RSB 129 Basic Rack Shelf (9.5 inches deep)
RSU 126 Universal Rack Shelf Kit (6 inches deep)
RSB 126 Basic Rack Shelf (6 inches deep)
MBU 125 1/2 Rack Width Low-Profile Mount Kit
Mounting the IPL T PC1 Interface
The IPL T PC1 can be set on a table, mounted on a rack shelf, or mounted under furniture
such as a desk, podium, or tabletop.
Tabletop Use
Four self-adhesive rubber feet are included with the PC1. For tabletop use, attach one foot
at each corner of the bottom side of the unit, and place the PC1 in the desired location.
Rack Mounting
Rack mount the interface, if desired, using one of the optional 19 inches wide rack shelves
UL requirements for rack mounting
The following Underwriters Laboratories (UL) requirements pertain to the installation of the
interface into a rack.
•
Elevated operating ambient temperature — If the equipment is installed in a closed
or multi-unit rack assembly, the operating ambient temperature of the rack environment
may be greater than room ambient temperature. Therefore, consider installing the
equipment in an environment compatible with the maximum ambient temperature
(TMA) specified by the manufacturer.
IPL T PC1 • SIS Programming and Control
64
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
Reduced air flow — Install the equipment in the rack so that the amount of air flow
required for safe operation of the equipment is not compromised.
Mechanical loading — Mount the equipment in the rack so that uneven mechanical
loading does not create a hazardous condition.
Circuit overloading — When connecting the equipment to the supply circuit, consider
the effect that circuit overloading might have on overcurrent protection and supply
wiring. Consider equipment nameplate ratings when addressing this concern.
•
Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted
equipment. Pay particular attention to supply connections other than direct connections
to the branch circuit (such as the use of power strips).
Rack mounting procedure
To mount the PC1 on a rack shelf:
1. If rubber feet have been installed on the bottom of the unit, remove them.
2. Mount the PC1 on the rack shelf, using two 4-40 x 3/16 inch screws in opposite
(diagonal) corners of the unit to secure it to the shelf.
3. Attach a blank panel or other units to the rack shelf.
RSU 129
1U Universal Rack Shelf
1/2 Rack Width Front False
Faceplate
1/4 Rack Width Front False
Faceplate
Both front false faceplates
use 2 screws.
(2) 4-40 x 3/16"
Screws
Use 2 mounting holes on
opposite corners.
Figure 43. Mounting the IPL T PC1 on an RSU 129 Universal Rack Shelf
4. Insert the shelf into the rack, aligning the holes in the shelf with those in the rack.
5. Secure the shelf to the rack using the supplied machine screws. This shelf can be
mounted in the front or in the rear of the rack.
Under-desk Mounting
The PC1 can also be mounted under furniture, such as a table or podium surface, using the
optional under-desk mounting kit MBU 125 (part number 70-077-01).
1. If rubber feet were previously installed on the bottom of the unit, remove them.
2. Attach the mounting brackets to the unit with the provided machine screws.
3. Insert #8 wood screws into the four pilot holes. Tighten each screw into the mounting
surface until slightly less than ¼ inch of the screw protrudes.
4. Align the mounting screws with the slots in the brackets, and place the PC1 against the
surface with the screws through the bracket slots.
IPL T PC1 • SIS Programming and Control
65
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Slide the unit slightly forward or back, then tighten all four screws to secure it in place.
Figure 44. Mounting the IPL T PC1 Under Furniture
IPL T PC1 • SIS Programming and Control
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Numbers and A
10/100Base-T
Ethernet that uses unshielded twisted pair (UTP - Cat 5, and so forth) cable, in which the
amount of data transmitted between two points in a given amount of time is equal to either
10 Mbps or 100 Mbps
ARP
(Address Resolution Protocol) A protocol that assigns an IP address to a device based on
the device’s MAC or physical machine address
AWG
C
(American Wire Gauge) A standard measurement for wire conductor diameter
Condition
A state for which the PC1 is being monitored. When a monitored condition is met, the PC1
may sound an alarm or send an e-mail message, depending on how the system has been
configured (via the front panel or the Monitor web page). Examples of conditions that can
be monitored include Receptacle Off, Any Change, or Reference: None.
Contact closure
An encapsulated switch containing two metal wires that serve as the contact points. When
these contact points meet, a complete circuit is created (for example, input to ground on the
IPL T PC1).
Custom web page Any file that can be loaded into an IPL interface and served by the IPL internal web server. A
custom web page can provide control of devices attached to the IPL without use of Global
Configurator (GC) or GlobalViewer (GV). This is true with or without an accompanying event
script. Any number and size of graphics can be used, but if they are too large to fit on the
IPL T PC1 interface, you can write your web page so that they can be served from another
web server. If you install Microsoft Internet Information Services (IIS) on your desktop, you
can serve any page on its hard disk. The IPL device functions like a little computer with a
web server—you can use it for various web tasks.
D
DataViewer
Software that allows you to send ASCII or hexadecimal commands to an IPL device interface
and view the device responses. You can configure the data display in several ways, including
selecting the text color, text font, and whether to view commands and responses in separate
panes within the DataViewer window. The software can save the command and response
data as a text file (.txt) or as an HTML file that preserves some of the display formatting.
Default web pages A set of preloaded web pages that can be accessed via a standard web browser. These pages
are a primary means of initial setup for IP Link products and a way to change their settings.
Web browsers such as Internet Explorer (version 5.5 or higher) can be used, but if using
Internet Explorer, you must also have Microsoft Script (version 5.6 or higher).
IPL T PC1 • Glossary
67
Download from Www.Somanuals.com. All Manuals Search And Download.
DHCP
Driver
E
(Dynamic Host Configuration Protocol) is a standardized communications protocol that
enables network administrators to locally and automatically manage the assignment of IP
addresses in an organization’s network.
This is a Global Configurator (GC) compatible package. It includes the event script that
controls devices.
Edison power receptacle
A standard power connector. The rear panel of the IPL T PC1, U. S. version, has a female
Edison receptacle (NEMA connector) into which a device is plugged in order to be powered
on and off by the PC1.
Ethernet
A network protocol that uses MAC addresses instead of IP addresses to exchange data
Ethernet devices can be connected to the Internet. An Ethernet LAN typically uses
unshielded twisted pair (UTP) wires. Ethernet systems currently provide transmission speeds
of 10 Mbps or 100 Mbps.
Event script
Executive mode
A program that runs on an IPL interface, and issues queries and commands to the attached
devices. Event scripts are written in the “Extron C” language (as .sc files), and are compiled
into event scripts using Global Configurator. The results are compiled as .evt files and loaded
onto the IPL interface. The Extron C language is similar to ANSI C, with some differences. As
long as event scripts are turned on, they run on the device continuously.
This is an operating mode in which the IPL T PC1 does not accept commands from the front
panel. Also called “front panel security lockout.”
F, G
Firmware
Embedded software that is stored permanently in read-only memory (ROM) and contains
basic instructions for how the PC1 operates. Firmware upgrades are periodically made
available for uploading via the IPL T PC1 Firmware Upgrade web page.
Gateway
A device that connects networks that have different, incompatible communication protocols.
The default gateway is the routing device used to forward all traffic that is not addressed to
a station within the local subnet.
Global Configurator (GC)
A windows program that, based on user input, creates the GlobalViewer (GV) pages. Global
Configurator requests system information, such as the devices you have and your current list
of IP addresses. With this information, GC creates a GV page for your specific devices. GC
also compiles the event scripts and loads the GV pages and event scripts onto the device.
When using GC, you must specify the port number for each device (for attached devices to
be controlled, they must be on that port). In order for multiple IP Link devices to appear in
the same GV page, all of the devices must be configured at the same time using GC.
IPL T PC1 • Glossary
68
Download from Www.Somanuals.com. All Manuals Search And Download.
GlobalViewer (GV) A set of web pages (HTML, XML, JS) and graphics that are loaded into the memory of an
IPL T PC1 interface. These pages provide an interface for control of devices attached to the
IPL T PC1 interface. They communicate with the event scripts running on the device, and the
event scripts issue the commands and queries. This communication between the web pages
and the event scripts occurs through predetermined memory locations in the IPL interface.
GV is initially created by Global Configurator (GC); however, it is possible to edit the GV
HTML, XML, and JavaScript files outside of GC. This edited GV is called “hard-coded” or
manually generated GlobalViewer.
H, I, M
HTTP
(HyperText Transfer Protocol) A web protocol, based on TCP/IP, that is used to fetch
HyperText objects from remote web pages
IEC power receptacle
A standard power connector. The IPL T PC1i rear panel has a female IEC receptacle into
which a device is plugged in order to be powered on and off by the PC1i.
IP
(Internet Protocol) The protocol or standard used to send information from one computer
to another on the Internet
IP address
A unique, 32-bit, binary number (up to a 12 digit decimal number, nnn.nnn.nnn.nnn) that
identifies each sender and each receiver of information connected to a LAN, WAN, or the
IP net mask/subnet mask
A 32-bit binary number (12 digit decimal number, nnn.nnn.nnn.nnn) used on subnets
(smaller, local networks) to help routers determine which network traffic gets routed
internally (within the subnetwork) to local computers and which network traffic goes out to
the rest of the network or the Internet
MAC
(Media Access Code) A unique hardware number given to devices that connect to the
Internet. When your computer or networking device (router, hub, interface, and so forth) is
its corresponding physical (MAC) address on the LAN.
P, R
Pass-through
Ping
Allows control systems to work with the IPL T PC1 interface, and provides a link between
two ports.
A utility and diagnostic tool that tests network connections. It is used to determine if the
host has an operating connection and is able to exchange information with another host.
Port number
A preassigned address within a server that provides a direct route from the application to the
transport layer or from the transport layer to the application of a TCP/IP system. The
standard ports used are 23 for Telnet and 80 for Ethernet.
Receptacle
A connector on a power supply that is equipped to receive a plug. The IPL T PC1 has one
receptacle into which a device can be plugged, enabling the PC1 to power the connected
device on and off.
IPL T PC1 • Glossary
69
Download from Www.Somanuals.com. All Manuals Search And Download.
S
SIS
(Simple Instruction Set) A set of commands developed by Extron that allow control of the
PC1 via the keyboard of a PC with an Ethernet connection. A minimal number of characters
are used in these commands and responses.
SMTP
(Simple Mail Transfer Protocol) An Internet standard for e-mail exchange across systems
or networks on the Internet
Standby reference threshold
The point at which a device starts to operate at standby power
Static IP
to a device or system in a network configuration. This type of address requires manual
configuration of the actual network device or system and can be changed only manually or
by enabling DHCP.
Subnet
Subnet address
The portion of an IP address that is specifically identified by the subnet mask as the
subnetwork
Subnet mask
Subnetwork
A 32-bit address mask used in IP to identify the bits of an IP address that are used for the
subnet address. Using a mask, the router does not need to examine all 32 bits, only those
selected by the mask.
(or Subnet) A network that is part of a larger IP network and is identified by a subnet
address. Networks can be segmented into subnetworks to provide a hierarchical, multilevel
routing structure.
T
TCP
TCP/IP
(Transmission Control Protocol) A connection-oriented protocol defined at the Transport
layer of the OSI reference model. It provides reliable delivery of data.
(Transmission Control Protocol/Internet Protocol) The communication protocol
(language) of the Internet. Computers and devices with direct access to the Internet are
provided with a copy of the TCP/IP program to allow them to send and receive information
in an understandable form.
Telnet
(Telecommunication Network) A utility available on most PCs that allows the computer
system to communicate with one of its remote users or clients. A user who wishes to access
a remote system initiates a Telnet session, using the address of the remote client. The user
may be prompted to provide a user name and password if the client is set up to require
them.
U, W
UID
(User ID) An optional user name for which a field is provided on the Enter Password
window that opens if a password has been assigned to the PC1
URL
(Universal Resource Locator) An address that lets a resource on the internet be identified,
located, and accessed
IPL T PC1 • Glossary
70
Download from Www.Somanuals.com. All Manuals Search And Download.
URL encoding
Web Server
URL encoding allows you to send information and commands to the unit to change its
configuration or provide you with feedback.
Resides on the IPL T PC1 interface and provides storage of the default web pages,
GlobalViewer, and your custom web pages.
IPL T PC1 • Glossary
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the
date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/
or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall
deem necessary to restore said product to proper operating condition, provided that it is returned within the warranty
period, with proof of purchase and description of malfunction to:
USA, Canada, South America,
Japan:
and Central America:
Extron Electronics
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe, Africa, and the Middle
East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Extron Asia
Middle East:
Extron Middle East
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical or
mechanical abuse, abnormal operating conditions, or modifications were made to the product that were not authorized
by Extron.
NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return
Authorization) number. This will begin the repair process.
USA: (714) 491-1500
Asia: 65.6383.4400
Europe: 31.33.453.4040
Japan: 81.3.3511.7655
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage
during shipment. Returned units must include the serial number and a description of the problem, as well as the name of
the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality,
performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct,
indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of
such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this warranty may not
apply to you.
Extron USA - West Extron USA - East Extron Europe
Extron Asia
Extron Japan
Extron China
Extron
Extron Korea
Extron India
Middle East
Headquarters
+81.3.3511.7655
FAX:
+81.3.3511.7656
+400.883.1568
Inside China Only
+971.4.2991800
FAX:
+971.4.2991880
+82.2.3444.1571 1800.3070.3777
+800.633.9876
Inside USA/Canada
Only
+800.633.9876
Inside USA/Canada
Only
+800.3987.6673
Inside Europe Only
+800.7339.8766
Inside Asia Only
Fax:
Inside India Only
+82.2.3444.1575
+86.21.3760.1568
FAX:
+86.21.3760.1566
+31.33.453.4040
FAX:
+31.33.453.4050
+65.6383.4400
FAX:
+65.6383.4664
+91-80-3055.3777
Fax:
+91 80 3055 3737
+1.714.491.1500
FAX:
+1.714.491.1517
+1.919.863.1794
FAX:
+1.919.863.1797
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Firstech LLC Automobile Alarm RF 2W900FM 5PT User Manual
Fisher Paykel Refrigerator N169T User Manual
Fisher Price Baby Toy 77831 User Manual
FOCUS Enhancements Camcorder FS 3 User Manual
Freeplay Energy Battery Charger I ECO C1 User Manual
Fujitsu Mouse FKB7614 SERIES User Manual
GE Air Conditioner AET05 User Manual
GE Freezer FCM5DM User Manual
GE Microwave Oven GE JVM1850 User Manual
Giant Bicycle METHOD 16 User Manual