FRONTRUNNERTM
AIR-COOLED MODELS
For Serial Nos.
720,000 & Higher
Part No. 4500-218 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
CONGRATULATIONS on the purchase of your
Exmark Mower. This product has been carefully
designed and manufactured to give you a maximum
amount of dependability and years of trouble-free
operation.
This manual contains operating, maintenance,
adjustment, and safety instructions for your Exmark
mower.
BEFORE OPERATING YOUR MOWER,
CAREFULLY READ THIS MANUAL IN ITS
ENTIRETY.
Figure 1
1. Model and serial number location
By following the operating, maintenance, and safety
instructions, you will prolong the life of your mower,
maintain its maximum efficiency, and promote safe
operation.
Model No.
Serial No.
If additional information is needed, or should you
require trained mechanic service, contact your
authorized Exmark equipment dealer or distributor.
All Exmark equipment dealers and distributors are
kept informed of the latest methods of servicing
and are equipped to provide prompt and efficient
service in the field or at their service stations. They
carry ample stock of service parts or can secure them
promptly for you from the factory.
All Exmark parts are thoroughly tested and inspected
before leaving the factory, however, attention is
required on your part if you are to obtain the fullest
measure of satisfaction and performance.
Whenever you need service, genuine Exmark parts,
or additional information, contact an Authorized
Service Dealer or Exmark Customer Service and have
the model and serial numbers of your product ready.
numbers on the product. Write the numbers in the
space provided.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Caster Pivot Bearings Pre-Load
Contents
Introduction ........................................................... 3
Engine (Briggs & Stratton Units
Lubricate Motion Control Bronze
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
• Never let children or untrained people operate
Safety
Safety Alert Symbol
this manual and on the machine to identify important
safety messages which must be followed to avoid
accidents
or service the equipment. Local regulations may
restrict the age of the operator.
• The owner/user can prevent and is responsible
for accidents or injuries occurring to himself or
herself, other people or property.
Preparation
This symbol means: ATTENTION! BECOME
ALERT! YOUR SAFETY IS INVOLVED!
• Evaluate the terrain to determine what accessories
and attachments are needed to properly and
safely perform the job. Only use accessories and
attachments approved by Exmark.
• Wear appropriate clothing including safety glasses,
substantial footwear, long trousers, and hearing
protection. Do Not operate when barefoot or
when wearing open sandals. Long hair, loose
clothing or jewelry may get tangled in moving
parts.
Figure 2
1. Safety alert symbol
The safety alert symbol appears above information
which alerts you to unsafe actions or situations
and will be followed by the word DANGER,
WARNING, or CAUTION.
CAUTION
DANGER: White lettering / Red background.
Indicates an imminently hazardous situation which, if
not avoided, Will result in death or serious injury.
This machine produces sound levels in
excess of 85 dBA at the operator’s ear and
can cause hearing loss through extended
periods of exposure.
WARNING: Black lettering / Orange background.
Indicates a potentially hazardous situation which, if
not avoided, Could result in death or serious injury.
Wear hearing protection when operating this
machine.
CAUTION: Black lettering / Yellow background.
Indicates a potentially hazardous situation which, if
not avoided, May result in minor or moderate injury.
• Inspect the area where the equipment is to be
used and remove all rocks, toys, sticks, wires,
bones, and other foreign objects which can be
thrown by the machine and may cause personal
injury to the operator or bystanders.
This manual uses two other words to highlight
information. Important calls attention to special
mechanical information and Note emphasizes
general information worthy of special attention.
Safe Operating Practices
Training
• Read the Operator’s Manual and other training
material. If the operator(s) or mechanic(s) can
not read English it is the owner’s responsibility to
explain this material to them.
• Become familiar with the safe operation of the
equipment, operator controls, and safety signs.
• All operators and mechanics should be trained.
The owner is responsible for training the users.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
DANGER
DANGER
In certain conditions gasoline is extremely
flammable and vapors are explosive.
In certain conditions during fueling, static
electricity can be released causing a spark
which can ignite gasoline vapors. A fire or
explosion from gasoline can burn you and
others and cause property damage.
A fire or explosion from gasoline can burn
you, others, and cause property damage.
• Fill the fuel tank outdoors in an open
area, when the engine is cold. Wipe up
any gasoline that spills.
• Always place gasoline containers on the
ground away from your vehicle before
filling.
• Never refill the fuel tank or drain the
machine indoors or inside an enclosed
trailer.
• Do Not fill gasoline containers inside a
vehicle or on a truck or trailer bed because
interior carpets or plastic truck bed liners
may insulate the container and slow the
loss of any static charge.
• Do Not fill the fuel tank completely
full. Add gasoline to the fuel tank until
the level is 1/4 to 1/2 inch (6–13 mm)
below the bottom of the filler neck. This
empty space in the tank allows gasoline
to expand.
• When practical, remove gas-powered
equipment from the truck or trailer and
refuel the equipment with its wheels on
the ground.
• Never smoke when handling gasoline,
and stay away from an open flame or
where gasoline fumes may be ignited by
spark.
• If this is not possible, then refuel such
equipment on a truck or trailer from a
portable container, rather than from a
gasoline dispenser nozzle.
• Store gasoline in an approved container
and keep it out of the reach of children.
• If a gasoline dispenser nozzle must be
used, keep the nozzle in contact with the
rim of the fuel tank or container opening
at all times until fueling is complete.
• Add fuel before starting the engine.
Never remove the cap of the fuel tank or
add fuel when engine is running or when
the engine is hot.
WARNING
• If fuel is spilled, Do Not attempt to start
the engine. Move away from the area of
the spill and avoid creating any source of
ignition until fuel vapors have dissipated.
Gasoline is harmful or fatal if swallowed.
Long-term exposure to vapors has caused
cancer in laboratory animals. Failure to use
caution may cause serious injury or illness.
• Do Not operate without entire exhaust
system in place and in proper working
condition.
• Avoid prolonged breathing of vapors.
• Keep face away from nozzle and gas
tank/container opening.
• Keep away from eyes and skin.
• Never siphon by mouth.
• Check that the operator’s presence controls,
safety switches, and shields are attached and
functioning properly. Do Not operate unless they
are functioning properly.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
• Be sure all drives are in neutral and parking brake
is engaged before starting engine. Use seat belts.
Operation
• Never operate the mower with damaged guards,
shields, or covers. Always have safety shields,
guards, switches and other devices in place and in
proper working condition.
WARNING
Operating engine parts, especially the
muffler, become extremely hot. Severe burns
can occur on contact and debris, such as
leaves, grass, brush, etc. can catch fire.
• Never mow with the discharge deflector raised,
removed or altered unless there is a grass
collection system or mulch kit in place and
working properly.
• Allow engine parts, especially the muffler,
to cool before touching.
• Do Not change the engine governor setting or
overspeed the engine.
• Remove accumulated debris from muffler
and engine area.
• Stop engine, wait for all moving parts to stop,
remove key and engage parking brake:
• Install and maintain in working order a
spark arrester before using equipment
on forest-covered, grass-covered, or
brush-covered unimproved land.
– Before checking, cleaning or working on the
mower.
– After striking a foreign object or abnormal
vibration occurs (inspect the mower for
damage and make repairs before restarting
and operating the mower).
WARNING
Engine exhaust contains carbon monoxide,
which is an odorless deadly poison that can
kill you.
– Before clearing blockages.
– Whenever you leave the mower.
• Stop engine, wait for all moving parts to stop, and
engage parking brake:
Do Not run engine indoors or in a small
confined area where dangerous carbon
monoxide fumes can collect.
– Before refueling.
– Before dumping the grass catcher.
WARNING
WARNING
Operating a FrontRunner tractor without an
approved Exmark front mount attachment
increases the possibility of forward tip over.
Tip-over could cause serious injury or death.
Hands, feet, hair, clothing, or accessories can
become entangled in rotating parts. Contact
with the rotating parts can cause traumatic
amputation or severe lacerations.
When operating a FrontRunner tractor
without an approved Exmark front mount
attachment, observe the following:
• Do Not operate the machine without
guards, shields, and safety devices in
place and working properly.
• Limit operation to minimum required to
install a different front mount attachment.
• Keep hands, feet, hair, jewelry, or clothing
away from rotating parts.
• Minimize speed and use extreme caution.
• Only operate on a flat level surface.
• NEVER carry passengers. DO NOT operate
the mower when people, especially children, or
pets are in the area.
• Do Not operate up or down a trailer ramp.
• Avoid sudden acceleration or deceleration.
• Be alert, slow down and use caution when making
turns. Look behind and to the side before
changing directions.
• Operate only in daylight or good artificial light,
keeping away from holes and hidden hazards.
• Stop the blades, slow down, and use caution when
crossing surfaces other than grass and when
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
transporting the mower to and from the area to
be mowed.
• Be aware of the mower discharge path and direct
discharge away from others.
• Do Not operate the mower under the influence
of alcohol or drugs.
• Use extreme care when loading or unloading the
machine into a trailer or truck.
• Use care when approaching blind corners, shrubs,
trees, or other objects that may obscure vision.
Slope Operation
Figure 3
Use Extreme caution when mowing and/or turning
on slopes as loss of traction and/or tip-over could
occur. The operator is responsible for safe operation
on slopes.
1. Safe Zone-Use the mower here on slopes less than 15
degrees
2. Danger Zone-Use a walk behind mower and/or hand
trimmer near drop-offs and water.
3. Water
DANGER
• Remove or mark obstacles such as rocks, tree
limbs, etc. from the mowing area. Tall grass can
hide obstacles.
Operating on wet grass or steep slopes can
cause sliding and loss of control. Wheels
dropping over edges, ditches, steep banks, or
water can cause rollovers, which may result
in serious injury, death or drowning.
• Watch for ditches, holes, rocks, dips and rises that
change the operating angle, as rough terrain could
overturn the machine.
• Do Not mow slopes when grass is wet.
• Do Not mow near drop-offs or near water.
• Avoid sudden stops when mowing downhill
because the mower may tip forwards.
• Do Not mow slopes greater than 15
degrees.
• Be aware that loss of traction may occur going
uphill. Weight transfer to the rear wheels may
cause drive wheels to slip and cause loss of
braking and steering.
• Reduce speed and use extreme caution
on slopes.
• Avoid sudden turns or rapid speed
changes.
• Always avoid sudden starting or stopping on a
slope. If tires lose traction, disengage the blades
and proceed slowly off the slope.
• See inside the back cover to determine the
approximate slope angle of the area to be mowed.
• Follow the manufacturer’s recommendations for
wheel weights or counter weights to improve
stability.
• Use a walk behind mower and/or a hand trimmer
near drop-offs, ditches, steep banks or water.
• Use extreme care with grass catchers or
attachments. These can change the stability of the
machine and cause loss of control.
Using the Rollover Protection System
(ROPS)
A Rollover Protection System (roll bar) is installed
on the unit.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
negative terminal first and the positive last.
Reconnect positive first and negative last.
WARNING
There is no rollover protection when the roll
bar is down. Wheels dropping over edges,
ditches, steep banks, or water can cause
rollovers, which may result in serious injury,
death or drowning.
• Use care when checking blades. Wrap the blade(s)
or wear gloves, and use caution when servicing
them. Only replace blades. Never straighten or
weld them.
• Keep hands and feet away from moving parts.
If possible, Do Not make adjustments with the
engine running.
• Keep the roll bar in the raised and locked
position and use seat belt.
• Charge batteries in an open well ventilated area,
away from spark and flames. Unplug charger
before connecting or disconnecting from battery.
Wear protective clothing and use insulated tools.
• Lower the roll bar only when absolutely
necessary.
• Do Not wear seat belt when the roll bar
is down.
• Keep all guards, shields and all safety devices in
place and in safe working condition.
• Drive slowly and carefully.
• Raise the roll bar as soon as clearance
permits.
• Check all bolts frequently to maintain proper
tightness.
• Frequently check for worn or deteriorating
components that could create a hazard.
• Check carefully for overhead clearances (i.e.
branches, doorways, and electrical wires) before
driving under any objects and Do Not contact them.
• All replacement parts must be the same as
or equivalent to the parts supplied as original
equipment.
Maintenance and Storage
• Disengage drives, lower implement, set parking
brake, stop engine and remove key or disconnect
spark plug wire. Wait for all movement to stop
before adjusting, cleaning or repairing.
WARNING
Hydraulic fluid escaping under pressure
can penetrate skin and cause injury. Fluid
accidentally injected into the skin must be
surgically removed within a few hours by a
doctor familiar with this form of injury or
gangrene may result.
• Keep engine, engine area, and pump drive belt
compartment free from accumulation of grass,
leaves, excessive grease or oil, and other debris
which can accumulate in these areas. These
materials can become combustible and may result
in a fire.
• Make sure all hydraulic fluid hoses
and lines are in good condition and
all hydraulic connections and fittings
are tight before applying pressure to
hydraulic system.
• Let engine cool before storing and Do Not store
near flame or any enclosed area where open pilot
lights or heat appliances are present.
• Keep body and hands away from pinhole
leaks or nozzles that eject high pressure
hydraulic fluid.
• Shut off fuel while storing or transporting. Do
Not store fuel near flames or drain indoors.
• Park machine on level ground. Never allow
untrained personnel to service machine.
• Use cardboard or paper, not your hands,
to find hydraulic leaks.
• Use jack stands to support components when
required.
• Safely relieve all pressure in the hydraulic
system by placing the motion control
levers in neutral and shutting off the
engine before performing any work on
the hydraulic system.
• Carefully release pressure from components with
stored energy.
• Disconnect battery or remove spark plug wire
before making any repairs. Disconnect the
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
Safety and Instructional Decals
• Keep all safety signs legible. Remove all grease,
dirt and debris from safety signs and instructional
labels.
• New safety signs may be obtained from
your authorized Exmark equipment dealer or
distributor or from Exmark Mfg. Co. Inc.
• Replace all worn, damaged, or missing safety
signs.
• Safety signs may be affixed by peeling off the
backing to expose the adhesive surface. Apply
only to a clean, dry surface. Smooth to remove
any air bubbles.
• When replacement components are installed, be
sure that current safety signs are affixed to the
replaced components.
• Familiarize yourself with the following safety signs
and instruction labels. They are critical to the safe
operation of your Exmark commercial mower.
• If an attachment or accessory has been installed,
make sure current safety signs are visible.
98-4361
98-5954
103-2076
1-513747
103-3270
1-523552
103-5881
1-643339
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
103-7218
107-2112
109-2355
109-2356
1. Fast
2. Slow
3. Neutral
4. Reverse
107-2102
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
109-2396
109-2357
4. Reverse
1. Fast
2. Slow
3. Neutral
5. Park Brake—Release
6. Park Brake—Engage
109-3637
109-2358
109-2377
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety
109-7413
4. Slow
1. Cylinder—extend
2. Cylinder—retract
3. Fast
5. Choke—on
6. Choke—off
109-7949
109-2360
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications
Model Numbers
Serial Nos: 720,000 and Higher
FR23KC; FR27KC; FR31BV
Systems
Safety Interlock System
• PTO must be disengaged, brake engaged, and
motion control levers out (neutral lock) to start
engine. (It is not necessary for the operator to be
in the seat to start the engine.)
Engine
• Engine Specifications: See your Engine Owner’s
Manual
• Operator must be in seat when PTO is engaged,
brake is disengaged, or motion control levers are
moved in or engine will stop.
• RPM: Full Speed: 3750 ±50 RPM (No Load)
Idle: 1500 RPM
• Engine will stop if the motion control levers
are moved from neutral position while brake is
engaged.
Fuel System
• Capacity: 8.5 gal. (32 L)
• Type of Fuel: Regular unleaded gasoline, 87
octane or higher.
Operator Controls
• Steering and Motion Control:
• Fuel Filter:
– Kohler:
Note: Motion control levers are adjustable to
three heights.
In-line 15 Micron Kohler P/N 2405010.
– Briggs & Stratton:
– Separate levers, on each side of the console,
control speed and direction of travel of the
respective drive wheels.
In-line 30 Micron Briggs P/N 695327.
• Fuel Shut-Off Valve: 1/4 turn increments (“ON”,
“OFF”).
– Steering is controlled by varying the position
of the levers relative to each other.
• Fuel gauge in right hand fuel tank.
– Moving motion control levers outward (in
slots) locks the drive system in neutral.
Electrical System
• Charging System: Flywheel Alternator
• Charging Capacity:
• PTO Engagement Lever: Engages drive to PTO
(mower deck).
• Parking Brake Lever: Engages parking brake by
pulling back.
– Kohler: 15 amps
– Briggs & Stratton: 20 amps
• Battery Type: BCI Group U1
• Battery Voltage: 12 Volt
• Polarity: Negative Ground
• Fuses:
Seat
• Type: Standard seat with high back, foam padded
(internal suspension) and armrests and integral
safety switch.
Optional seat accessories:
– Kohler:
– Custom ride suspension system to enhance
Standard Seat.
One 15 amp and two 20 amp blade type
– Briggs & Stratton:
– Deluxe suspension seat with high back, low
profile foam-in-place cushion (dampened,
adjustable spring suspension) and armrests.
One 15 amp, one 20 amp, and one 30 amp
blade type
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
• Mounting: Hinged to tilt up for access to
hydraulic pumps, battery and other components.
The seat is held in the tilted position with a
linkage. Adjustable fore and aft seat track.
Tires & Wheels
27HP Kohler & 31HP Briggs & Stratton Units
Drive
Front
Caster
Rear Caster
(Dual Tail
Wheel)
• Armrests: Standard seat: foam padded flip-up
armrests. Optional suspension seat: molded
adjustable flip-up armrests.
Pneumatic
(Air-Filled) Pneumatic
Semi-
Semi-
Pneumatic
• Seat Safety Switch: Internal to the bottom seat
cushion, non serviceable. Time delay module
incorporated into the Safety Interlock System
eliminates rough ground cut-outs.
Quantity
Tread
Size
2
2
2
AT101
Smooth
9 x 3.50-4
Smooth
13 x 6.5-6
24 x
12.00-12
Hydrostatic Ground Drive System
Ply Rating
Pressure
4
• Hydrostatic Pumps:
9 psi
(62 kPa)
– 27HP Kohler & 31HP Briggs & Stratton
Units: Two Hydro Gear PR 16 cc variable
displacement piston pumps.
23HP Kohler Units
Drive
Front
Caster
Rear Caster
(Single Tail
Wheel)
– 23HP Kohler Units: Two Hydro Gear PJ
12 cc variable displacement piston pumps.
• Wheel Motors: Hydro Gear planetary reduction
motors.
Pneumatic
Semi-
Semi-
Pneumatic
(Air-Filled) Pneumatic
• Hydraulic Oil Type: Use Mobil 1 15W-50
Synthetic motor oil.
Quantity
Tread
Size
2
2
1
Turfmate
Smooth
9 x 3.50-4
Smooth
13 x 6.5-6
• Hydraulic Oil Capacity:
23 x
10.50-10
– 27HP Kohler & 31HP Briggs & Stratton
Units: 5.2 qt. (4.9 L)
Ply Rating
Pressure
4
13 psi
(90 kPa)
– 23HP Kohler Units: 4.0 qt. (3.8 L)
• Hydraulic Filter: Replaceable cartridge type.
P/N 103-2146: 25 microns, No bypass
• Speeds:
Cutting Deck
(Sold Separately)
• Model Numbers:
– FR524
– 27HP Kohler & 31HP Briggs & Stratton
Units:
0-10.5 mph (16.9 km/hr) forward
0-6.6mph (10.6 km/hr) reverse
– 23HP Kohler Units:
– FR604
– FR724
• Cutting Width:
– 52 inch (132 cm)
– 60 inch (152 cm)
– 72 inch (183 cm)
• Discharge: Side
• Blade Size: (3 ea.)
0-8.7 mph (14.0 km/hr) forward
0-5.7mph (9.2 km/hr) reverse
• Drive wheel release valves allow machine to be
moved when engine is not running.
– 52 inch Deck: 18.00 inches (45.7 cm)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
– 60 inch Deck: 20.50 inches (52.1 cm)
– 72 inch Deck: 24.50 inches (62.2 cm)
23HP Kohler
27HP Kohler &
31HP Briggs &
Stratton
• Blade Spindles: Solid steel spindles with 1 3/4
inch (4.45 cm) I.D. bearings.
60 inch Deck
72 inch Deck
112.4 inches
(285.5 cm)
114.3 inches
(290.3 cm)
• Deck Drive: “B”-Section belt from jackshaft on
deck to blade spindles.
114.3 inches
(290.3 cm)
• Deck: Full floating deck is attached to out-front
support frame, removable for service. Six
anti-scalp rollers provide maximum turf
protection. Deck design allows for bagging,
mulching or side discharge.
Overall Height:
Roll Bar - Up
Roll Bar - Down
50.7 inches (128.8 cm)
69.2 inches (175.8 cm)
• Deck Depth:
Tread Width: (Center to Center of
Tires, Widthwise)
– 52 inch Deck: 5.5 inches (14.0 cm)
– 60 inch Deck: 5.5 inches (14.0 cm)
– 72 inch Deck: 5.5 inches (14.0 cm)
27HP Kohler & 31 HP Briggs & Stratton Units
• Cutting Height Adjustment: Adjusts from 1 1/2
inches (3.8 cm) to 5 inches (12.7 cm) infinitely
variable.
52 inch Deck
60 inch Deck
72 inch Deck
41.4 inches
(105.2 cm)
41.4 inches
(105.2 cm)
45.4 inches
(115.3 cm)
• Mulching Kit: Optional
• Bagger: Optional
23HP Kohler Units
52 inch Deck
60 inch Deck
72 inch Deck
Dimensions
38.9 inches
(98.8 cm)
38.9 inches
(98.8 cm)
Overall Width:
52 inch
Deck
60 inch
Deck
72 inch
Deck
Wheel Base: (Center of Caster Tire to
Center of Drive Tire)
• 27HP Kohler & 31HP Briggs & Stratton Units:
51.2 inches (130.0 cm)
Without
Deck
49.0 inches 49.0 inches 53.0 inches
(124.5 cm) (124.5 cm) (135 cm)
Deflector
Up
53.3 inches 61.4 inches 73.4 inches
(135.4 cm) (156 cm)
(186 cm)
• 23HP Kohler Units: 54.1 in (137.4 cm)
Deflector
Down
64.0 inches 72.0 inches 84.3 inches
(163 cm)
(183 cm)
(214 cm)
Minimum Turning Radius
• 27HP Kohler & 31HP Briggs & Stratton Units:
55.25 inches (140.3 cm)
Overall Length:
• 23HP Kohler Units: 56.3 in (143.0 cm)
23HP Kohler
27HP Kohler &
31HP Briggs &
Stratton
Curb Weight:
Without deck
and floor pan
folded
80.4 inches
(204.2 cm)
82.3 inches
(209.0 cm)
Without deck
52 inch Deck
60 inch Deck
72 inch Deck
911 lb (413 kg)
1303 lb (591 kg)
1348 lb (611 kg)
1397 lb (634 kg)
52 inch Deck
112.4 inches
(285.5 cm)
114.3 inches
(290.3 cm)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Overview
Torque Requirements
Product Overview
Bolt Location
Torque
Engine Mounting Bolts
Wheel Lug Nuts
30-35 ft-lb (41-47 N-m)
90-95 ft-lb (122-129 N-m)
72-77 ft-lb (98-104 N-m)
Wheel Motor Mounting
Bolts
Wheel Hub Lock Nut
210-250 ft-lb
(285-339 N-m)
Rollover Protection System 30-35 ft-lb (41-47 N-m)
(Roll Bar) Mounting Bolts
Clutch Retaining Bolt
55-60 ft-lb (75-81 N-m)
(secured with threadlocker)
Figure 4
4. Seat Belt
1. Fuel Cap
2. Roll Bar
3. Controls
5. Motion Control Lever
6. Parking Brake Lever
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Push the lever forward and down to disengage the
brake.
Operation
Note: Determine the left and right sides of the
The unit must be tied down and brake engaged when
transporting.
machine from the normal operating position.
Controls
Ignition Switch
Located on right fuel tank console.
Motion Control Levers
The ignition switch is used to start and stop the
engine. The switch has three positions “OFF”, “ON”
and “START”. Insert key into switch and rotate
clockwise to the “ON” position. Rotate clockwise to
the next position to engage the starter (key must be
held against spring pressure in this position).
The motion control levers located on each side of the
console control the forward and reverse motion of
the machine. The levers control the flow of hydraulic
oil from the hydrostatic pump to the drive wheel
motor for each side.
Moving the levers forward or backward turns the
wheel on the same side forward or in reverse. Wheel
speed is proportional to the amount the lever is
moved.
Note: Brake must be engaged, motion control levers
out (neutral lock position), and PTO switch “OFF”
to start engine. (It is not necessary for the operator
to be in the seat to start the engine.)
Moving the levers outward from the center position
into the T-slot locks them in the neutral position
Hour Meter
Located on the right fuel tank console.
Choke Control
The hour meter is connected to a pressure switch
installed in the engine block and it records the
number of hours that the engine has run. If the
ignition switch is left on without engine running,
hour meter will not run.
Located on right fuel tank console.
The choke is used to aid in starting a cold engine.
Moving the choke lever forward will put the choke in
the “ON” position and moving the choke lever to the
rear, to the detent, will put the choke in the “OFF”
position. Do Not run a warm engine with choke in
the “ON” position.
Note: This switch is not a low oil sensor and will not
alert the operator if the engine oil is low.
Fuel Shut-Off Valve
Throttle Control
Located in fuel line by fuel tank and fuel filter.
Located on right fuel tank console.
The fuel shut-off valve is used to shut off the fuel
when the machine will not be used for a few days,
during transport to and from the jobsite, and when
parked inside a building.
The throttle is used to control engine speed. Moving
the throttle lever forward will increase engine speed
and moving the throttle lever to the rear will decrease
engine speed. Moving the throttle forward into the
detent is full throttle.
Rotate the valve 1/4 turn clockwise to shut off fuel.
Rotate the valve 1/4 turn counterclockwise to turn
on fuel.
Park Brake Lever
Located on left side of unit, between the seat and the
dummy tank.
Fuel Gauge
Located at the rear of the right fuel tank.
The brake lever engages a parking brake on the drive
wheels.
The fuel gauge monitors the amount of fuel in the
right fuel tank only. The left tank does not hold fuel.
Pull the lever up and rearward to engage the brake.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Drive Wheel Release Valves
Make sure you understand the controls, their
locations, their functions, and their safety
requirements.
Located on the top left front corner of hydrostatic
pumps.
Refer to the Maintenance section and perform all the
necessary inspection and maintenance steps.
Drive wheel release valves are used to release the
hydrostatic drive system to allow the machine to be
pushed without the engine running.
Operating Instructions
With a wrench, turn both valves one turn
counterclockwise to release drive system. Turn
clockwise to reset system. Do Not overtighten. Do
Not tow machine.
Raise the Rollover Protection System
(ROPS)
• For 27HP Kohler & 31HP Briggs & Stratton
Units: Use a 5/8 inch wrench to turn the valves.
Important: Lower the roll bar only when
absolutely necessary.
• For 23HP Kohler Units: Use a 7/16 inch wrench
to turn the valves.
1. Remove the hairpin cotter pins and remove the
2. Raise the roll bar to the upright position and
install the two pins and secure them with the
PTO Engagement Switch
Located on right fuel tank.
Important: Always use the seat belt with the
roll bar in the raised position. Ensure that the
rear part of the seat is secured with the seat
latch.
Switch must be pulled out to the “ROTATE”
position to engage the blades. Switch is pushed in to
the “STOP” position to stop the blades.
Hydraulic Lift Switch
Located on right fuel tank console.
The hydraulic lift switch is used to raise and lower
the mower deck.
Push the front portion of the hydraulic lift switch
down to raise the mower deck to the desired height.
Push the rear portion of the hydraulic lift switch
down to lower the mower deck to the desired height.
Pre-Start
Fill fuel tanks. For best results use only clean, fresh
regular grade unleaded gasoline with an octane rating
of 87 or higher. Regular grade leaded gasoline may
also be used; however, combustion chamber and
cylinder head will require more frequent service. See
Engine Owner’s Manual.
Figure 5
Do Not add oil to gasoline.
1. Roll bar
2. Raised position
3. Pin
4. Hairpin cotter pin
Do Not overfill fuel tank. Never fill the fuel tank so
that the fuel level rises above a level that is 1/2 inch
(13 mm) below the bottom of the filler neck to allow
for fuel expansion and prevent fuel spillage.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Open the Fuel Shut-Off Valve
DANGER
The fuel shut-off valve is located on the right side of
unit in fuel line next to the fuel filter. Raise the rear
hood to access fuel shut-off valve.
An uncovered discharge opening will allow
objects to be thrown in an operator’s or
bystander’s direction. Also, contact with the
blade could occur. Thrown objects or blade
contact can cause serious injury or death.
Starting the Engine
1. Move the motion control levers out to the neutral
lock position.
Never operate the mower with the discharge
deflector raised, removed, or altered unless
there is a grass collection system or mulch
kit in place and working properly.
2. Pull up and back on the parking brake lever to
engage the parking brake.
3. Push in on the PTO switch to the “STOP”
position.
The PTO push-pull switch engages the cutting blades.
Be sure that all persons are clear of the mower deck
and discharge area before engaging PTO.
Note: It is not necessary for the operator to be
in the seat to start the engine.
Important: Operator must be in seat before the
PTO can be engaged.
4. Place the throttle midway between the “SLOW”
and “FAST” positions.
1. Set the throttle to the “MIDWAY” position.
5. On a cold engine, push the choke lever forward
into the “ON” position.
2. Pull the PTO switch outward to the “ROTATE”
position.
On a warm engine, leave the choke in the “OFF”
position.
3. Place the throttle in the “FAST” position to begin
mowing.
6. Turn ignition switch to the “START” position.
Release the switch as soon as the engine starts.
Disengaging the PTO
1. Set the throttle to the “MIDWAY” position.
Important: Do Not crank the engine
continuously for more than ten seconds at a
time. If the engine does not start, allow a 60
second cool-down period between starting
attempts. Failure to follow these guidelines
can burn out the starter motor.
2. Push the PTO switch in to the “STOP” position
to disengage the blades.
Stopping the Engine
1. Bring the unit to a full stop.
2. Disengage the PTO.
7. If the choke is in the “ON” position, gradually
return choke to the “OFF” position as the engine
warms up.
3. Move the motion control levers out to the neutral
lock position.
4. Engage the parking brake.
Engaging the PTO
5. Place the throttle midway between the “SLOW”
and “FAST” positions.
DANGER
The rotating blades under the mower deck
are dangerous. Blade contact can cause
serious injury or kill you.
6. Allow the engine to run for a minimum of 15
seconds, then turn the ignition switch to the
“OFF” position to stop the engine.
7. Remove the key to prevent children or other
unauthorized persons from starting engine.
Do Not put hands or feet under the mower
or mower deck when the blades are engaged.
8. Close the fuel shut-off valve when the machine
will not be in use for a few days, when
transporting, or when the unit is parked inside
a building.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Driving the Machine
3. To move forward in a straight line apply equal
forward pressure to both levers.
To turn left or right, pull the motion control lever
back toward neutral in the direction desired.
CAUTION
Machine can spin very rapidly by positioning
one lever too much ahead of the other.
Operator may lose control of the machine,
which may cause damage to the machine
or injury.
The machine will move faster the farther the
motion control levers are moved away from
neutral.
4. To stop, pull the motion control levers back to
the neutral position.
• Use caution when making turns.
• Slow the machine down before making
sharp turns.
Important: To begin movement (forward or
backward) the operator must be in the seat, the
brake lever must be disengaged (pushed down)
before the motion control levers can be moved in
or the engine will stop.
When levers are centered in the T-slot the drive
system is in the neutral position. With levers moved
out in the T-slot the drive system is in the neutral lock
Figure 7
1. Handles Out (Neutral
Lock)
4. Forward
2. Handles In (Neutral)
3. Front of Unit
5. Reverse
Driving in Reverse
Figure 6
1. Move the motion control levers inward to the
center to the neutral unlocked position.
1. Handles Out (Neutral
Lock)
2. Handles In (Neutral)
3. Front of Unit
4. Forward
5. Neutral
2. To move rearward in a straight line applying equal
pressure pull both motion control levers rearward.
6. Reverse
7. Neutral Lock
To turn left or right, release pressure on the
motion control lever toward the direction desired.
Driving Forward
3. To stop, push the motion control levers to the
neutral position.
1. Release the parking brake.
2. Move the motion control levers inward to the
center to the neutral unlocked position.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Loading a Unit
Transporting
Use extreme caution when loading units on trailers
or trucks. One full width ramp is required. If it is
not possible to use one full width ramp, use enough
individual ramps to simulate a full width continuous
ramp.
Transporting a Unit
Important: Do Not transport FrontRunner
tractor without an approved Exmark front mount
attachment.
Ramp should be long enough so that the angles
between the ramp and the ground and the ramp and
the trailer or truck do not exceed 15°. A steeper angle
may cause mower deck components to get caught as
the unit moves from ramp to trailer or truck. Steeper
angles may also cause the unit to tip. If loading on or
near a slope, position the trailer or truck so it is on
the down side of the slope and the ramp extends up
the slope. This will minimize the ramp angle. The
trailer or truck should be as level as possible.
Use a heavy-duty trailer or truck to transport the
machine. Lock brake and block wheels. Securely
fasten the machine to the trailer or truck with straps,
chains, cable, or ropes. Be sure that the trailer or truck
has all necessary lighting and marking as required by
law. Secure a trailer with a safety chain.
CAUTION
This unit does not have proper turn
Important: Do Not attempt to turn the unit
while on the ramp, you may lose control and
drive off the side.
signals, lights, reflective markings, or a
slow moving vehicle emblem. Driving on a
street or roadway without such equipment
is dangerous and can lead to accidents
causing personal injury. Driving on a street
or roadway without such equipment may also
be a violation of State laws and the operator
may be subject to traffic tickets and/or fines.
Avoid sudden acceleration when driving on a ramp.
Do Not drive a unit on a public street or
roadway.
WARNING
Loading a unit on a trailer or truck increases
the possibility of tip-over. Tip-over could
cause serious injury or death.
• Use extreme caution when operating a
unit on a ramp.
• Use only a single, full width ramp; Do
Not use individual ramps for each side
of the unit.
• If individual ramps must be used, use
enough ramps to create an unbroken
ramp surface wider than the unit.
• Do Not exceed a 15° angle between ramp
and ground or between ramp and trailer
or truck.
• Avoid sudden acceleration while driving
unit on a ramp.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Maintenance
Note: Determine the left and right sides of the machine from the normal operating position.
WARNING
WARNING
While maintenance or adjustments are being
made, someone could start the engine.
Accidental starting of the engine could
seriously injure you or other bystanders.
The engine can become very hot. Touching
a hot engine can cause severe burns.
Allow the engine to cool completely before
service or making repairs around the engine
area.
Remove the key from the ignition switch,
engage parking brake, and pull the wire(s)
off the spark plug(s) before you do any
maintenance. Also push the wire(s) aside
so it does not accidentally contact the spark
plug(s).
Recommended Maintenance Schedule(s)
Maintenance Service
Maintenance Procedure
Interval
• Change the engine oil.
After the first 5 hours
After the first 100 hours
After the first 250 hours
• Check the wheel hub locknuts torque specification.
• Change the hydraulic filter.
• Check the engine oil level.
• Check the safety interlock system.
• Check the rollover protections systems (roll bar) pins.
• Check the seat belt.
Before each use or daily
• Check for loose hardware.
• Clean the engine cooling system.
• Remove accumulated debris from engine.
• Check the hydraulic oil level.
• Check the tire pressures.
• Check the condition of the belts.
• Grease hitch and cylinder pivots.
• Grease the dual tail wheel pivot (if applicable).
Every 40 hours
• Service the air cleaner. (May need more often under severe conditions. See the Engine
Owner’s Manual for additional information.)
Every 50 hours
Every 80 hours
Every 100 hours
• Remove the engine shrouds and clean the cooling fins.
• Change the engine oil. (May need more often under severe conditions.)
• Grease the fold pivot pin.
• Lubricate the brake handle pivot.
• Lubricate the brake rod bushings.
• Lubricate the motion control bronze bushings.
• Lubricate the steering linkage rod ends.
• Check the spark plugs.
Every 160 hours
Every 500 hours
• Check the wheel hub locknuts torque specification.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Maintenance Service
Interval
Maintenance Procedure
• Check the battery charge.
Monthly
• Grease the fold lock pin.
• Grease the rear caster pivot.
• Grease the belt idlers.
• Grease the motion control pivots.
• Grease the transfer spring ends.
• Lubricate the caster wheel hub(s).
• Lubricate the motion control shaft.
• Change the hydraulic filter.
Yearly
Periodic Maintenance
Allowing batteries to stand for an extended period of
time without recharging them will result in reduced
performance and service life. To preserve optimum
battery performance and life, recharge batteries in
storage when the open circuit voltage drops to 12.4
volts.
Check Engine Oil Level
Service Interval: Before each use or daily
1. Stop engine and wait for all moving parts to stop.
Make sure unit is on a level surface.
Note: To prevent damage due to freezing, battery
should be fully charged before putting away for
winter storage.
2. Tilt seat forward and raise hood to gain access
to access to engine area.
3. Check with engine cold.
Check the voltage of the battery with a digital
voltmeter. Locate the voltage reading of the battery in
the table and charge the battery for the recommended
time interval to bring the charge up to a full charge
of 12.6 volts or greater.
4. Clean area around dipstick. Remove dipstick and
wipe oil off. Reinsert the dipstick and push it all
the way down into the tube. Remove the dipstick
and read the oil level.
5. If the oil level is low, wipe off the area around the
oil fill cap, remove cap and fill to the “FULL”
mark on the dipstick. Use oil as specified in
Engine Owner’s Manual. Do Not overfill.
Important: Make sure the negative battery
cables are disconnected and the battery charger
used for charging the battery has an output of
16 volts and 7 amps or less to avoid damaging
the battery (see chart for recommended charger
settings).
Important: Do Not operate the engine with the
oil level below the “LOW” (or “ADD”) mark on
the dipstick, or over the “FULL” mark.
Check Battery Charge
Service Interval: Monthly
WARNING
CALIFORNIA
Proposition 65 Warning
Battery posts, terminals, and related
accessories contain lead and lead
compounds, chemicals known to the State of
California to cause cancer and reproductive
harm. Wash hands after handling.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Run engine at one-third throttle, engage PTO
and raise off of seat (but do not get off of
machine) engine must initiate shutdown after
1/2 second has elapsed.
Voltage
Reading
Percent
Charge
Maximum Charging
Charger
Settings
Interval
12.6 or
greater
100%
No
Charging
Required
16 volts/7
amps
Run engine at one-third throttle, with brake
disengaged, move levers in and raise off seat (but
do not get off of machine) engine must initiate
shutdown after 1/2 second has elapsed.
12.4 – 12.6 75–100%
12.2 – 12.4 50–75%
30 Minutes
16 volts/7
amps
1 Hour
16 volts/7
amps
Again, run engine at one-third throttle, brake
engaged, and move left motion control lever in
- engine must initiate shutdown.
12.0–12.2
11.7–12.0
25–50%
0–25%
2 Hours
3 Hours
14.4 volts/4
amps
Repeat again moving the right lever in, then
moving both levers in - engine must initiate
shutdown whether operator is on seat or not.
14.4 volts/4
amps
11.7 or less 0%
6 Hours or
More
14.4 volts/2
amps
3. Check the PTO circuit. See the FR524, FR604,
and FR724 Operator’s manual to become familiar
with the deck operation. Open the folding
deck latches, disengage the park brake, move
the motion control levers in to neutral, and
disengage the PTO. Lower the deck until the
PTO switch arm is no longer depressing the PTO
Check Safety Interlock
System
Service Interval: Before each use or daily
Note: To prevent engine cut-outs on rough terrain
the seat kill switch has a 1/2 second delay.
1. Check starting circuit. Starter should crank with,
parking brake engaged, PTO disengaged and
motion control levers moved out in the neutral
lock position. The operator does not need to be
in the seat to start the engine.
Try to start with operator in seat, parking brake
disengaged, PTO disengaged and motion control
levers in the neutral lock position - starter must
not crank.
Try to start with operator in seat, parking brake
engaged, PTO engaged and motion control
levers in the neutral lock position - starter must
not crank.
Try to start with operator in seat, parking
brake engaged, PTO disengaged, and the left
motion control lever in, starter must not crank,
repeat again with the right lever in, then with
both levers in - starter must not crank.
Figure 8
Left Side—Inside of Hitch Shown
1. PTO “Kill” Switch
2. PTO Switch Arm
3. Lower deck until arm Does Not contact the switch.
2. Check the kill circuits. Run engine at one-third
throttle, disengage parking brake and raise off
of seat (but do not get off of machine) engine
must initiate shutdown after approximately 1/2
second has elapsed (seat has time delay kill switch
to prevent cut-outs on rough terrain).
Run the engine at half throttle and pull up on the
PTO engagement switch.
The PTO must not engage.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Note: If machine does not pass any of these tests,
Do Not operate. Contact your authorized EXMARK
SERVICE DEALER.
B. Remove paper element. Check the
condition of the paper element. Replace if
dirty, bent or damaged.
C. Check the condition of the inner element.
Replace whenever it appears dirty, typically
every other time the paper element is
replaced. Clean the base around the inner
element before removing, so dirt does not
get into the engine.
Important: It is essential that operator safety
mechanisms be connected and in proper
operating condition prior to use for mowing.
Check Rollover Protections
Systems (Roll Bar) Pins
D. Do Not wash or use pressurized air to
clean paper element or inner element.
Service Interval: Before each use or daily
E. Reinstall elements. Position the cover so
that the rubber dust ejector is pointing
downward and secure with retaining clips.
Make sure latch pin and hair pin are fully installed
and lanyard is in good condition.
• For 23 HP Kohler Units:
Check Seat Belt
Service Interval: Before each use or daily
A. Remove foam pre-cleaner element and
wash in warm water with detergent. Rinse
until all traces of detergent are eliminated
and squeeze out excess water (Do Not
wring). Air dry. Saturate with engine oil
and squeeze out excess oil.
Visually inspect seat belt for wear, cuts, and proper
operation of retractor and buckle. Replace before
operating if damaged.
B. Check paper element. Do Not wash or
use pressurized air to clean paper element.
Replace if dirty, bent or damaged.
Check for Loose Hardware
Service Interval: Before each use or daily
C. Reinstall foam pre-cleaner to paper
element, then reinstall paper element and
cover.
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. Visually inspect machine for any loose hardware
or any other possible problem. Tighten hardware
or correct the problem before operating.
Change Engine Oil
Service Interval: After the first 5 hours
Service Air Cleaner
Every 100 hours/Yearly
(whichever comes first)
(May need more often
under severe conditions.)
Service Interval: Every 50 hours (May
need more often under
severe conditions. See
the Engine Owner’s
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
Manual for additional
information.)
2. Tilt seat forward and raise hood to gain access
to the engine area.
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
3. Drain oil while engine is warm from operation.
2. Tilt seat forward and raise hood to gain access
to the air cleaner.
4. Fit hose in literature pack over oil drain valve.
Rotate the valve 1/4 counterclockwise and gently
pull outward to open the valve. Allow the oil to
drain, then close the valve by pushing inward and
rotating 1/4 turn clockwise. Remove and retain
the hose for future use.
• For 27HP Kohler & 31HP Briggs & Stratton
Units:
A. Loosen retaining clips and remove air
cleaner compartment cover.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
5. Replace the oil filter every other oil change. Clean
around oil filter and unscrew filter to remove.
Before reinstalling new filter, apply a thin coating
of oil on the surface of the rubber seal. Turn
filter clockwise until rubber seal contacts the filter
adapter then tighten filter an additional 2/3 to
3/4 turn.
3. Tilt the seat forward.
4. Locate the auxiliary hydraulic power unit reservoir
6. Clean around oil fill cap and remove cap. Fill to
specified capacity and replace cap.
7. Use oil recommended in engine owner’s manual.
Do Not overfill. Start the engine and check for
leaks.
Check Hydraulic Oil Level
Service Interval: Every 40 hours
Figure 9
1. Stop engine and wait for all moving parts to stop.
Engage parking brake.
1. Auxiliary hydraulic reservoir plug
2. Tilt seat up.
5. Clean area around the reservoir plug and remove.
Oil level should be up to the reservoir plug hole.
If not, add oil. Use only Mobil 1 15W-50 synthetic
motor oil. Replace reservoir plug and tighten until
snug. Do Not overtighten.
3. Clean area around hydraulic reservoir cap and
remove cap. Oil level should be to the top of the
baffle inside the tank. If not, add oil. Use only
Mobil 1 15W-50 synthetic motor oil. Replace
hydraulic reservoir cap and tighten until snug. Do
Not overtighten.
Check Tire Pressures
Service Interval: Every 40 hours
Note: The baffle is labeled “HOT” and
“COLD”. The oil level varies with the
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
temperature of the oil. The “HOT” level shows
the level of oil when it is at 225°F (107°C). The
“COLD” level shows the level of the oil when
it is at 75°F (24°C). Fill to the appropriate level
depending upon the temperature of the oil. For
example: If the oil is about 150°F (65°C), fill to
halfway between the “HOT” and “COLD” levels.
If the oil is at room temperature (about 75°F
(24°C)), fill only to the “COLD” level.
2. Check tire pressure in drive tires.
• For 23HP Kohler Units: The drive tires
should be inflated to 13 psi (90 kpa).
• For 27HP Kohler & 31HP Briggs & Stratton
Units: The drive tires should be inflated to 9
psi (62 kpa).
3. The rear caster tire(s) is semi-pneumatic and does
not need to be inflated.
Check Auxiliary Hydraulic
Oil Level
Note: Do Not add any type of tire liner or foam
fill material to the tires. Excessive loads created by
foam filled tires may cause failures to the hydro drive
system, frame, and other components. Foam filling
tires will void the warranty.
Service Interval: As required
Note: Check the auxiliary hydraulic oil level if there
is evidence of a leak or the hydraulic cylinder does
not perform normally.
1. Retract the hydraulic cylinder.
2. Stop engine and wait for all moving parts to stop.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Check Condition Of Belts
Service Interval: Every 40 hours
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. Check pump and PTO drive belts.
3. Belts are spring tensioned and no adjustment is
necessary. See Pump Drive Belt Tension and
Replacement sections in Adjustments.
Lubricate Grease Fittings
Note: See chart for service intervals.
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. Lubricate fittings with one to two pumps of
NGLI grade #2 multi-purpose gun grease.
3. Lubricate front caster pivots once a year. Remove
hex plug and cap. Thread grease zerk in hole and
pump with grease until it oozes out around top
bearing. Remove grease zerk and thread plug back
in. Place cap back on.
Refer to the following chart for fitting locations
and lubrication schedule.
Lubrication Chart
Fitting
Locations
Initial
Pumps
Number of
Places
Service
Interval
Lubricate Rear Caster Wheel
Hub(s)
2
4
40 Hours
1. Hitch
and Cylinder
Pivots
Service Interval: Yearly
2
2
2
2
1
2
2
100 Hours
Yearly
2. Fold
Pivot Pin
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
3. Fold
Lock Pin
4. Rear
Caster Pivot
*0
1
*Yearly
Yearly
5. Belt
Idlers
6. Motion
Control
Pivots
1
Yearly
1
2
4
1
7. Transfer
Spring Ends
Yearly
Figure 10
1. Seal guard
2. Spacer nut with wrench
flats
8. Dual
Tail Wheel
Pivot (if
40 Hours
applicable)
2. Remove caster wheel from caster forks.
3. Remove seal guards from the wheel hub.
* See step 3 for special lubrication instructions
on the rear caster pivots and the Lubricate Rear
Caster Wheel Hub section for special lubrication
instructions on the rear casters wheel hub.
4. Remove one of the spacer nuts from the axle
assembly in the caster wheel. Note that thread
locking adhesive has been applied to lock the
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
spacer nuts to the axle. Remove the axle (with
the other spacer nut still assembled to it) from
the wheel assembly.
2. Tilt seat forward.
3. Lubricate bronze bushings on brake handle pivot
with a spray type lubricant or light oil.
5. Pry out seals, and inspect bearings for wear or
damage and replace if necessary.
6. Pack the bearings with a NGLI grade #1
multi-purpose grease.
Lubricate Brake Rod
Bushings
7. Insert one bearing, one new seal into the wheel.
Service Interval: Every 160 hours
Note: Seals (Exmark P/N 103-0063) must be
replaced.
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
8. If the axle assembly has had both spacer nuts
removed (or broken loose), apply a thread locking
adhesive to one spacer nut and thread onto the
axle with the wrench flats facing outward. Do
Not thread spacer nut all of the way onto the end
of the axle. Leave approximately 1/8 inch (3 mm)
from the outer surface of the spacer nut to the
end of the axle inside the nut.
2. Tilt seat forward and raise hood.
3. Lubricate bronze bushings on each end of the
brake rod shaft with a spray type lubricant or
light oil (bushings are located to the inside of the
flange bearings).
Lubricate Motion Control
Bronze Bushings
9. Insert the assembled nut and axle into the wheel
on the side of the wheel with the new seal and
bearing.
Service Interval: Every 160 hours
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
10. With the open end of the wheel facing up, fill
the area inside the wheel around the axle full of
NGLI grade #1 multi-purpose grease.
2. Unhook seat latch and tilt seat up.
11. Insert the second bearing and new seal into the
wheel.
12. Apply a thread locking adhesive to the 2nd spacer
nut and thread onto the axle with the wrench flats
facing outward.
13. Torque the nut to 75-80 in-lb (8-9 N-m), loosen,
then re-torque to 20-25 in-lb (2-3 N-m). Make
sure axle does not extend beyond either nut.
3. Lubricate bronze bushings on flange bearings
securing the motion control arm shafts with a
light oil or a spray type lubricant.
Lubricate Motion Control
Shaft
Service Interval: Yearly
14. Reinstall the seal guards over the wheel hub and
insert wheel into caster fork. Reinstall caster bolt
and tighten nut fully.
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. Tilt seat forward.
Important: To prevent seal and bearing damage,
check the bearing adjustment often. Spin the
caster tire. The tire should not spin freely
(more than 1 or 2 revolutions) or have any side
play. If the wheel spins freely, adjust torque on
spacer nut until there is a slight amount of drag.
Reapply thread locking adhesive.
3. Remove tab at rear of motion control shaft.
4. Pull motion control shaft out and lubricate with
an NGLI grade #2 multi-purpose gun grease.
5. Re-install shaft and tab.
Lubricate Steering Linkage
Rod Ends
Lubricate Brake Handle Pivot
Service Interval: Every 160 hours
Service Interval: Every 160 hours
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
2. Tilt seat forward.
3. Lubricate each end of both steering linkage rods
with a spray lubricant or light oil
CAUTION
Raising the mower for service or maintenance
relying solely on mechanical or hydraulic
jacks could be dangerous. The mechanical or
hydraulic jacks may not be enough support
or may malfunction allowing the unit to fall,
which could cause injury.
Check Spark Plugs
Service Interval: Every 160 hours
Remove spark plugs, check condition and reset gaps,
or replace with new plugs. See Engine Owner’s
Manual.
Do Not rely solely on mechanical or hydraulic
jacks for support. Use adequate jack stands
or equivalent support
Change Fuel Filter
6. Start engine and move throttle control ahead to
full throttle position. Move the speed control
levers to the full speed and run for several
minutes. Shut down machine and recheck oil
level.
Service Interval: As required
A fuel filter is installed between the fuel tanks and the
engine. Replace when necessary.
Replacement Filters
Note: Do Not change hydraulic system oil (except
for what can be drained when changing filter), unless
it is felt the oil has been contaminated or been
extremely hot.
Changing oil unnecessarily could damage hydraulic
system by introducing contaminates into the system.
Kohler
Kohler
P/N 2405010–15 Micron
Briggs & Stratton
Briggs & Stratton
P/N 695327– 30 Micron
Change Hydraulic System
Filter
Check Wheel Hub Locknuts
Service Interval: After the first 100 hours
Service Interval: After the first 250 hours
Yearly thereafter
Every 500 hours thereafter
Note: Use only Exmark Part No. 103-2146.
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
When tightening the lock nut on the wheel motor
tapered shaft:
Torque to 210-250 ft-lb (285-339 N-m).
2. Carefully clean area around filter. It is important
that no dirt or contamination enter hydraulic
system.
Note: Do Not use antiseize on wheel hub.
Fuel Tank — Mounting
Hardware Specifications
Service Interval: As required
3. Unscrew filter to remove and allow oil to drain
from reservoir.
Important: Before reinstalling new filter, fill
it with Mobil 1 15W-50 and apply a thin coat
of oil on the surface of the rubber seal.
When installing the nuts on the fuel tank studs, fully
tighten the nyloc nut and back off 1/2 turn. This
allows for normal fuel tank expansion and contraction
with changes in temperature and fuel levels.
Turn filter clockwise until rubber seal contacts the
filter adapter, then tighten the filter an additional
2/3 to 3/4 turn.
4. Fill reservoir as stated in Check Hydraulic Oil
Level section.
Thread Locking Adhesives
5. Raise the rear of machine up and support with
jack stands (or equivalent support) just high
enough to allow drive wheels to turn freely.
Thread locking adhesives such as “Loctite 242”
or “Fel-Pro, Pro-Lock Nut Type” are used on the
following fasteners:
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
• Pump drive sheave set screws.
• Line shaft sheave setscrews.
Adjustments
Note: Disengage PTO, shut off engine, wait for
all moving parts to stop, engage parking brake, and
remove key before servicing, cleaning, or making any
adjustments to the unit.
• Square head setscrews on Hydro pump control
arms.
• Sheave retaining bolt in the end of engine
crankshaft.
Pump Drive Belt Tension
Self-tensioning - No adjustment necessary.
• Caster wheel spacer nuts.
• Fuel tank bulkhead fitting nuts.
• Motion control tab retaining bolt.
Pump Drive Belt
Replacement
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
Adhesives such as “Loctite RC/609 or RC/680” or
“Fel-Pro Pro-Lock Retaining I or Retaining II” are
used on the following:
Fuel tank studs, where studs are inserted into tank.
2. Remove pump drive belt.
Dielectric Grease
Dielectric grease is used on all blade type electrical
connections to prevent corrosion and loss of contact.
3. Route new belt onto sheaves as shown in the
decal located on the right hand side of the left
Figure 11
Park Brake Adjustment
Check to make sure brake is adjusted properly.
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. Tilt seat forward and raise hood.
3. Pull the brake lever up into the engaged position.
4. Locate the park brake spring assembly (see
mm) between the yoke and thin nyloc nut on the
brake bolt. If necessary, rotate the thin nyloc nut
to obtain the 1/8 inch gap.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
remove the bolt that secures the ball joint to
the brake lever and loosen the jam nut next to
the ball joint. Rotate the ball joint in half-turns
counterclockwise until desired disengagement is
obtained.
Motion Control Linkage
Adjustment
WARNING
Engine must be running and drive
wheels must be turning so motion control
adjustment can be performed. Contact with
moving parts or hot surfaces may cause
personal injury
Figure 12
3. Thin nyloc nut
Keep fingers, hands, and clothing clear of
rotating components and hot surfaces.
1. Park brake engaged
2. Yoke
4. 1/8 inch (3 mm) gap
between nut and yoke.
1. This adjustment must be made with the drive
wheels turning. First raise the frame and block up
so that drive wheels can rotate freely.
5. If park brake does not fully disengage when the
lever is disengaged check the brake rod linkage
assembly. The assembly should measure 7 3/8
inch (18.7 cm) from the center of the ball joint
to the center of the lower end of the linkage rod
2. Remove the electrical connection from the seat
safety switch, located directly in front of the seat
switch assembly.
3. Temporarily install a jumper wire across the
terminals in the connector of the main wiring
harness.
4. Start the engine.
5. Run the unit at least 5 minutes with the drive
levers at full forward speed to bring hydraulic
system oil up to operating temperature.
6. To obtain the neutral position, adjust the left and
right pump control rod linkages that connect the
steering control to the pump control arms until
the wheels stop, or creep slightly in reverse.
7. To adjust each linkage, loosen the jam nut next
the ball joint at the upper end of the linkage
rod assembly. Then rotate the assembly using a
wrench to turn the double nuts on the assembly
Figure 13
1. Ball joint
2. Jam nut
3. Park brake linkage rod
4. 7 3/8 inch (18.7 cm)
8. Re-tighten the jam nut against the ball joint on
each side.
6. If the linkage does not measure 7 3/8 inch
(18.7 cm) or still does not disengage as desired,
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Figure 14
Figure 15
3. Fender knob
1. Loosen jam nut
1. Motion control lever
2. Left fender
2. Pump control rod linkage
3. Use wrench to turn double nuts
3. Slide the fender forward and twist upward and
outward to remove.
9. Move the motion control levers to the reverse
position. Return the motion control levers to
neutral. The wheels must stop turning (or slightly
creep in reverse).
4. To adjust the weight transfer springs, fold
the mower deck and front frame and lock in
service position. See Deck Manual for complete
instructions.
10. Stop engine and wait for all moving parts to stop.
Remove jumper wire from wire harness connector
and plug connector into seat switch.
WARNING
11. Lower from jackstands.
Weight transfer springs may have stored
energy. Removing the weight transfer
springs without releasing the stored energy
can cause serious injury.
Weight Transfer Spring
Adjustment
Fold mower deck and front frame and lock in
service position to remove spring tension and
release stored energy before performing any
maintenance or adjustments on the weight
transfer springs. (See Deck Manual for Deck
Raising instructions).
Weight transfer springs are assembled from the
factory to apply the maximum amount of weight onto
the drive wheels. This setting provides the greatest
amount of traction. Some conditions may require
the rear wheel lift to be reduced. This can be done
by reducing the amount to weight transfer, which
will increase the amount of weight on the front and
rear casters.
5. Remove the retaining ring and washer at either
end of the weight transfer spring that retains it to
the transfer bellcrank pins and/or weight transfer
1. Rotate the left motion control arm up and into
the operation position.
2. Locate and loosen the knob under the rear of the
6. Pull the spring off of front or rear pin and
re-install in the outer hole, to reduce the spring
force. Re-install the washer and retaining ring.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning
Clean Engine Cooling
System
Service Interval: Before each use or daily
(May be required more
often in dry or dirty
conditions.)
CAUTION
Figure 16
Excessive debris around the engine cooling
air intake and inside of the pump drive
belt compartment and damaged or missing
rubber baffles can cause the engine and
hydraulic system to overheat which can
create a fire hazard.
Right-Hand Side of Unit Shown
1. Re-install spring in outer 3. Remove e-ring and
holes to reduce spring
washer.
tension.
2. Weight transfer spring.
Clean all debris from inside of pump drive
belt compartment daily.
7. Re-install the left fender
8. For additional weight transfer adjustment, repeat
steps 4 through 7 on the right side of the unit.
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
Caster Pivot Bearings
Pre-Load Adjustment
Remove dust cap from caster and tighten nyloc nut
until washers are flat and back off 1/4 of a turn
to properly set the pre-load on the bearings. If
disassembled, make sure the spring disc washers are
2. Clean all debris from rotating engine air intake
screen and from around engine shrouding.
3. Clean all debris from around the engine and drive
belts.
Remove Accumulated Debris
from Engine (Briggs &
Stratton Units Only)
Service Interval: Before each use or daily
Engine parts should be kept clean to reduce the risk
of overheating and ignition of accumulated debris.
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. Remove front panel from engine and clean around
the intake manifold, fuel pump, and carburetor.
3. Reinstall the front panel.
Important: Do Not use water to clean engine.
Use low pressure compressed air. See Engine
Owner’s Manual.
Figure 17
1. Spring disc washers
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Remove Engine Shrouds and
Clean Cooling Fins
Service Interval: Every 80 hours
1. Stop engine, wait for all moving parts to stop, and
remove key. Engage parking brake.
2. Remove cooling shroud clean-out covers from
engine and clean cooling fins. Also clean dust,
dirt, and oil from external surfaces of engine,
which can cause improper cooling.
3. Make sure cooling shroud clean-out covers are
reinstalled. Operating the engine without cooling
shroud clean-out covers will cause engine damage
due to overheating.
Waste Disposal
Motor Oil Disposal
Engine oil and hydraulic oil are both pollutants to
the environment. Dispose of used oil at a certified
recycling center or according to your state and local
regulations.
Battery Disposal
DANGER
Battery electrolyte contains sulfuric acid,
which is poisonous and can cause severe
burns. Swallowing electrolyte can be fatal or
if it touches skin can cause severe burns.
• Wear safety glasses to shield eyes, and
rubber gloves to protect skin and clothing
when handling electrolyte.
• Do Not swallow electrolyte.
Federal law states that batteries should not be placed
in the garbage. Management and disposal practices
must be within relevant federal, state, or local laws.
If a battery is being replaced or if the unit containing
the battery is no longer operating and is being
scrapped, take the battery to a local certified recycling
center. If no local recycling is available return the
battery to any certified battery reseller.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
Important: It is essential that all operator safety mechanisms be connected and in proper operating
condition prior to mower use.
When a problem occurs, Do Not overlook the simple causes. For example: starting problems could be
caused by an empty fuel tank.
The following table lists some of the common causes of trouble. Do Not attempt to service or replace major
items or any items that call for special timing of adjustment procedures (such as valves, governor, etc.). Have
this work done by your Engine Service Dealer.
Note: When disconnecting electrical connectors Do Not pull on the wires to separate the connectors.
Problem
Starter does not crank
Possible Cause
1. PTO is engaged.
Corrective Action
1. Disengage the PTO.
2. Parking brake is not.
2. Set the parking brake.
3. Drive levers are not in neutral lock
position.
3. Ensure the drive levers are in the neutral
lock position.
4. Battery does not have a full charge.
4. Charge the battery.
5. Electrical connections are corroded, loose 5. Check the electrical connections for
or faulty.
good contact. Clean connector terminals
thoroughly with electrical contact cleaner,
apply dielectric grease and reconnect.
6. Fuse is blown.
6. Replace the blown fuse.
7. Relay or switch is defective.
7. Contact an Authorized Service Dealer.
Engine will not start, starts hard, or fails to
keep running
1. Fuel tank is empty.
1. Fill the fuel tank.
2. Fuel shutoff valve is closed.
3. Oil level in the crankcase is low.
2. Open the fuel shutoff valve.
3. Add oil to the crankcase.
4. The throttle and choke are not in the
correct position.
4. Be sure the throttle control is midway
between the “SLOW” and “FAST”
positions, and the choke is in the “ON”
position for a cold engine or the “OFF”
position for a warm engine.
5. Dirt in fuel filter.
5. Replace the fuel filter.
6. Dirt, water, or stale fuel is in the fuel
system.
6. Contact an Authorized Service Dealer.
7. Air cleaner is dirty.
7. Clean or replace the air cleaner element.
8. Electrical connections are corroded, loose 8. Check the electrical connections for
or faulty.
good contact. Clean connector terminals
thoroughly with electrical contact cleaner,
apply dielectric grease and reconnect.
9. Relay or switch is defective.
10. Faulty spark plug.
11. Spark plug wire is not connected.
9. Contact an Authorized Service Dealer.
10. Clean, adjust or replace spark plug.
11. Check the spark plug wire connection.
Engine loses power
1. Engine load is excessive
1. Reduce the ground speed.
2. Air cleaner is dirty.
3. Oil level in the crankcase is low.
2. Clean or replace the air cleaner element.
3. Add oil to the crankcase.
4. Cooling fins and air passages for the
engine are plugged.
4. Remove the obstructions from the cooling
fins and air passages.
5. Vent hole in the fuel cap is plugged.
6. Dirt in fuel filter.
5. Clean or replace the fuel cap.
6. Replace the fuel filter.
7. Dirt, water, or stale fuel is in the fuel
system.
7. Contact an Authorized Service Dealer.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Possible Cause
Corrective Action
Engine overheats
1. Engine load is excessive
1. Reduce the ground speed.
2. Oil level in the crankcase is low.
2. Add oil to the crankcase.
3. Cooling fins and air passages for the
engine are plugged.
3. Remove the obstructions from the cooling
fins and air passages.
Mower pulls left or right (with levers fully
forward)
1. Tracking needs adjustment
1. Adjust the tracking.
2. Tire pressure in drive tires not correct.
2. Adjust tire pressure in the drive tires.
3. Reverse indicator and motion control
linkage need adjustment.
3. Adjust the reverse indicator and the
motion control linkage.
Machine does not drive
1. Bypass valve is not closed tight.
1. Tighten the bypass valve.
2. Change the belt.
2. Drive or pump belt is worn, loose or
broken.
3. Drive or pump belt is off a pulley.
4. Broken or missing idler spring.
5. Hydraulic fluid level is low or too hot.
3. Change the belt.
4. Replace the spring.
5. Add hydraulic fluid to reservoir or let it
cool down.
Abnormal vibration
1. Engine mounting bolts are loose.
1. Tighten the engine mounting bolts.
2. Tighten the appropriate pulley.
2. Loose engine pulley, idler pulley, or blade
pulley.
3. Engine pulley is damaged.
3. Contact an Authorized Service Dealer.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Schematics
Schematics
Electrical Diagram —23HP & 27HP Kohler
G R E Y
W H I T E
C A K B L
C A K B L
D K G R E E N /
W H I T E
C A K B L
C A K B L
D K G R E E N
D K G R E E N
G R E Y
G R E Y
O R A N G E
P I N K / B L
C A K
O R A N G E
G R E Y
G R E Y
D K G R E E N
D K G R E E N
K C A
W H I T E
O R A N G E / B L
W O N R B
D K G R E E N /
C A K B L
W O Y E L L
A T N
W O N R B
D K G R E E N
D K G R E E N
C A K
P I N K / B L
T L B L U E
T L B L U E
T L B L U E
W O N R B
D K G R E E N
T L G R E E N
T L B L U E
T L B L U E
C A K B L
A T N
T L G R E E N
T L B L U E
A T N
G R E Y
O R A N G E
G R E Y
G R E Y
C A K
C A K
G R E Y / B L
G R E Y / B L
W O N R B
G007220
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Schematics
Electrical Diagram – 31HP Briggs & Stratton
C A K L B / W O Y E L L
V I O L E T
C A K B L
C A K B L
A T N
G R E Y
W H I T E
C A K B L
C A K B L
W H I T E
D K G R E E N /
C A K B L
C A K B L
G R E Y
G R E Y
D K G R E E N
O R A N G E
P I N K / B L
D K G R E E N
C A K
O R A N G E
G R E Y
G R E Y
D K G R E E N
D K G R E E N
K C A
W H I T E
O R A N G E / B L
W O N R B
D K G R E E N /
C A K B L
W O Y E L L
D K G R E E N
D K G R E E N
A T N
W O N R B
C A K
P I N K / B L
T L B L U E
T L B L U E
T L B L U E
W O N R B
D K G R E E N
T L G R E E N
T L B L U E
T L B L U E
C A K B L
A T N
T L G R E E N
T L B L U E
A T N
G R E Y
O R A N G E
G R E Y
G R E Y
C A K
C A K
G R E Y / B L
G R E Y / B L
W O N R B
G007221
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Schematics
Hydraulic Diagram
BYPASS VALVE
BYPASS VALVE
HIGH PRESSURE
FORWARD
HIGH PRESSURE
REVERSE
HIGH
HIGH PRESSURE
FORWARD
PRESSURE
REVERSE
G007220
HIGH PRESSURE
CHARGE PUMP
CASE DRAIN
40
Download from Www.Somanuals.com. All Manuals Search And Download.
2-Year Limited Warranty
Exmark Turf Equipment
(For units purchased on or after October 1, 2004)
Contact any Exmark Service Dealer to arrange service at their
Conditions and Products Covered
Exmark Mfg. Co. Inc. and its affiliate, Exmark Warranty
Company, pursuant to an agreement between them, jointly
warrant on the terms and conditions herein, that we will repair,
replace or adjust any part manufactured by Exmark and found
by us (in the exercise of our reasonable discretion) to be
defective in factory materials or workmanship for a period of
two years.
dealership. To locate a dealer convenient to you, access our
402-223-6375.
If for any reason you are dissatisfied with the Service Dealer’s
analysis or with the assistance provided, contact us at:
Exmark Customer Service Department
The Exmark Warranty Company
2101 Ashland Avenue
Beatrice, NE 68310
402-223-6375 or
This warranty applies to Exmark turf equipment purchased on
or after October 1, 2004 sold in the US or Canada. This
warranty may only be assigned or transferred to a second (or
third) owner by an authorized Exmark dealer. The warranty
period commences upon the date of the original retail
purchase.
Owner’s Responsibilities
The Exmark turf equipment, including any defective part,
must be returned to an authorized Exmark service dealer
within the warranty period. This warranty extends only to turf
equipment operated under normal conditions. You must read
the operator’s manual. You must also properly service and
maintain your Exmark product as described in the operator’s
manual. Such routine maintenance, whether performed by a
dealer or by you, is at your expense.
Products
Warranty Period
2 years
1 year
1 year
90 days
1 Year Prorated
• All Products (except as noted below)
• All Attachments and Accessories
• Metro 21 and Metro 26 Series
• Belts and Tires
• Battery
• Engine*
Warranty is covered by engine manufacturer
* Please refer to the engine manufacturer’s warranty statement
that is included in the literature packet. We are not authorized
to handle warranty adjustments on engines.
General Conditions
The sole liability of Exmark and Exmark Warranty Company
with respect to this warranty shall be repair and replacement
of defective components as set forth herein. Neither Exmark
nor Exmark Warranty Company shall have any liability
for any other cost, loss or damage, including but not
limited to, any incidental or consequential loss or damage.
This warranty only includes the cost of parts and labor.
Items and Conditions Not Covered
This warranty does not cover the following:
• Pickup and delivery charges to and from any authorized
Exmark Service Dealer beyond first warrantable service.
• Any damage or deterioration due to normal use, wear and
tear, or exposure.
• Cost of regular maintenance service or parts, such as filters,
fuel, lubricants, tune-up parts, and adjustments.
• Any product or part which has been altered or misused or
required replacement or repair due to normal wear,
accidents, or lack of proper maintenance.
• Any repairs necessary due to use of parts, accessories or
supplies, including gasoline, oil or lubricants, incompatible
with the turf equipment or other than as recommended in
the operator's manual or other operational instructions
provided by Exmark.
In particular, we shall have no liability or responsibility for:
• Expenses related to gasoline, oil or lubricants.
• Travel time, overtime, after hours time or other
extraordinary repair charges or charge relating to repairs or
replacements outside of normal business hours at the place
of business of the authorized Exmark Service Dealer.
• Rental of like or similar replacement equipment during the
period of any warranty, repair or replacement work.
• Any telephone or telegram charges or travel charges.
• Loss or damage to person or property other than that
covered by the terms of this warranty.
• Any claims for lost revenue, lost profit or additional cost as
a result of a claim of breach of warranty.
• Attorney's fees.
There are no other express warranties except for engine and
special emission system coverage stated elsewhere herein or
included with the product.
No Claim of breach of warranty shall be cause for cancellation
or rescission of the contract of sale of any Exmark mower.
All warranty work must be performed by an authorized
Exmark Service Dealer using Exmark approved replacement
parts.
Some states do not allow exclusions of incidental or
consequential damages, so the above exclusions and
limitations may not apply to you.
Instructions for Obtaining Warranty Service
The product must be registered with original proof of purchase
by an Exmark Service Dealer before obtaining any warranty
service.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
G006117
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Record
Date:
Description of Work Done:
Service Done By:
42
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
SEE EXMARK’S COMPLETE LINE OF ACCESSORIES
MID-MOUNT RIDING ACCESSORIES
CUSTOM RIDE SEAT SUSPENSION SYSTEM
DECK LIFT ASSIST KIT
HITCH KIT
ROLL OVER PROTECTION SYSTEM (ROPS)
SNOW BLADE
SUN SHADE
LAZERLOCKER
TRASH CONTAINER
LIGHT KIT
TURF STRIPER
MICRO-MULCH SYSTEM
OPERATOR CONTROLLED DISCHARGE
ULTRA VAC COLLECTION SYSTEM
ULTRA VAC QUICK DISPOSAL SYSTEM
OUT-FRONT RIDING ACCESSORIES
CUSTOM RIDE SEAT SUSPENSION SYSTEM
DUAL-TAIL WHEEL
SNOW BLADE
SNOWBLOWER
FLOOR PAN EXTENDER
HITCH KIT
SUN SHADE
TRASH CONTAINER
LIGHT KIT
ULTRA VAC COLLECTION SYSTEM
ULTRA VAC QUICK DISPOSAL SYSTEM
WEATHER CAB
MICRO-MULCH SYSTEM
ROLL OVER PROTECTION SYSTEM (ROPS)
ROTARY BROOM
WALK-BEHIND ACCESSORIES
GRASS CATCHER
LAZERLOCKER
TURF STRIPER
STANDON
MICRO-MULCH SYSTEM
Place Model No. and Serial No.
Label Here (Included in the Literature
Pack) or Fill in Below
Date Purchased
Engine Model No. and Spec. No.
Engine Serial No. (E/No)
Model No.
Serial No.
© 2004–2008 Exmark Mfg. Co., Inc.
Industrial Park Box 808
Beatrice, NE 68310
Part No. 4500-218 Rev. A
(402) 223-6300
Fax (402) 223-5489
Printed in the USA.
All Rights Reserved
Download from Www.Somanuals.com. All Manuals Search And Download.
|