Installation and Operation Guide
High Flow CSR Filter Systems
Selecting A Mounting locAtion
1. Give consideration to the weight of the unit when operating (filled with water). Operating weights
of High Flow CSR Systems are:
• Twin System - 45 lbs (20.2 kg)
• Triple System - 47 lbs (21.2 kg)
• Quad System - 49 lbs (22.2 kg)
• Quad Plus System - 49 lbs (21.2 kg) + separate surge/storage tank @ 60 lbs (27.2 kg)
2. The location should allow for (See figures 1-8):
• Minimum clearance of 21⁄2" under the cartridge(s) so it can be lowered for removal and
replacement.
• Adequate space for “in” and “out” water line connections. Be near a drain for flushing and near
a 110V outlet if the optional Everguard™ Low Pressure Alarm is used.
• Additional mounting and floor space for the separate SR-X Feeder and surge/storage tank† (Quad
Plus).
Figure 1 – Twin
Figure 2 – Triple
Figure 3 – Quad
operAting SpecificAtionS*
replacement
cartridge
combined Model name
flow rate
capacity
High Flow CSR Twin - MC
High Flow CSR Twin - MC2
High Flow CSR Twin - XC
High Flow CSR Twin - XC2
High Flow CSR Twin - 4CB5
High Flow CSR Twin - 7CB5
High Flow CSR Triple - MC
High Flow CSR Triple - MC2
High Flow CSR Triple - XC
High Flow CSR Triple - XC2
High Flow CSR Triple - 4CB5
High Flow CSR Triple - 7CB5
High Flow CSR Quad - MC
High Flow CSR Quad - MC2
High Flow CSR Quad Plus - XC
High Flow CSR Quad Plus - XC2
MC
MC2
XC
3.3 gpm (12.5 lpm) 18,000 gal.(68,000 L)
3.3 gpm (12.5 lpm) 18,000 gal.(68,000 L)
3.3 gpm (12.5 lpm) 18,000 gal.(68,000 L)
3.3 gpm (12.5 lpm) 18,000 gal.(68,000 L)
3.3 gpm (12.5 lpm) 12,000 gal.(45,400 L)
5.0 gpm (18.9 lpm) 20,000 gal.(75,700 L)
5.0 gpm (18.9 lpm) 27,000 gal.(102,000 L)
5.0 gpm (18.9 lpm) 27,000 gal.(102,000 L)
5.0 gpm (18.9 lpm) 36,000 gal.(136,000 L)
5.0 gpm (18.9 lpm) 36,000 gal.(136,000 L)
5.0 gpm (18.9 lpm) 18,000 gal.(68,000 L)
7.5 gpm (28.5 lpm) 30,000 gal.(113,550 L)
6.6 gpm (25.2 lpm) 36,000 gal.(136,000 L)
6.6 gpm (25.2 lpm) 36,000 gal.(136,000 L)
6.6 gpm (25.2 lpm) 48,000 gal.(181,600 L)
6.6 gpm (25.2 lpm) 48,000 gal.(181,600 L)
XC2
4CB5
7CB5
MC
MC2
XC
XC2
4CB5
7CB5
MC
MC2
XC
XC2
* For individual cartridge specifications, refer to cartridge literature.
temperature: 35-100°F (2-38°C)
pressure:
10 - 125 psi (0.7 - 8.6 bar), non-shock
For cold water use only.
inStAllAtion
1. Use the predrilled mounting holes in the manifold bracket as guides. Mark and drill anchor holes.
Mount securely. See Figures 5-8.
2. Shut off power to equipment. If system is a High Flow CSR Quad Plus (separate SR-X Feeder and
surge/storage tank†), proceed to step 3b.
3a. Connect outlet ports of High Flow system to equipment served per the instructions below. Always
use NSF approved pipe dope or Teflon tape at all connections. Use a backup wrench on all fittings
while connecting to avoid stress on the system components.
• The cross fitting before the SR-X Feeder has a threaded outlet on top. Connect a minimum 1/2"
I.D. line from this outlet to fountain beverage equipment.
• The cross fitting has a flushing valve installed on the bottom. Connect tubing to the flushing valve
and run to drain. Note: Some municipal plumbing codes and good sanitary practices require an
air gap at the drain termination point.
Figure 4 – Quad Plus
Manufactured by Everpure
EV3112-78 Rev E AP08
Download from Www.Somanuals.com. All Manuals Search And Download.
cArtriDge cHAnge DeterMinAtion
Replace the prefilter cartridge whenever it becomes excessively dirty (observed visually or by flow restriction). Follow the change instructions provided with
the cartridge. Replace carbon filter cartridges when capacity is reached or when flow becomes inadequate, but at least annually. All carbon filter cartridges
on multiple cartridge systems should be changed at the same time. Change the SS-10 cartridge when product level in the cartridge drops below 1/2" from
the bottom of the bowl.
The system pressure gauge or optional Everguard™ Low Pressure Alarm (LPA) provides a quick, simple means of determining when the filter cartridge(s)
should be checked. Installed on the system outlet manifold, the gauge or LPA can be used to monitor both dynamic (flowing) and static (line) pressure. The
cartridge(s) should be changed when the pressure gauge is in the red area while equipment is in operation, and yet the needle shows adequate line pressure
between cycles. Observe the needle during the next equipment on cycle. If the needle registers adequate pressure, it can be assumed that the temporary
low-pressure condition was caused by a brief power failure or other incoming pressure disruption. If the low pressure condition is not due to an external
condition, check/change the prefilter first. If the low pressure condition is still not corrected, change the carbon filter cartridges.
preSSure gAugeS
Adequate Outlet
Pressure
Low Inlet
Pressure
Adequate Inlet
Pressure
Low Outlet
Pressure
cArtriDge cHAnge proceDure
3. Clean bowl with filtered water only;
e-Series prefilter cartridge change
NO SPECIAL CLEANERS.
1. Shut off power to equipment. Shut
off inlet water ahead of system.
2. Push red relief valve. Unscrew
bowl. Remove prefilter cartridge.
4. Feel head o-ring. If dry, lubricate
with high quality silicone lubricant.
5. Install new prefilter cartridge in
bowl. Hand tighten bowl onto head.
6. Turn on water. Turn on power to
equipment.
flushing
4. Pull cartridge downward and out of
everpure carbon filter cartridge
change
2. Open flushing valve to relieve
pressure.
head.
6. Turn cartridge right 90˚ until
rotation stops.
8. With flushing valve fully open, open
inlet water at full force for five
minutes. Close flushing valve.
5. Hold head firmly. Align cartridge
lug with label. Insert new cartridge
firmly into head.
1. Shut off power to equipment. Shut
off inlet water ahead of system.
3. Hold head firmly and push upward.
Turn cartridge to left until it stops.
7. Repeat steps 3-6 for remaining
cartridges.
9. Turn on power to equipment
8. Turn on water.
Sr-X feeder cartridge change
2. Press red pressure relief button on
4. Remove old cartridge.
6. Install new SS-10 cartridge into
9. Press red pressure relief button
head.
head.
until water comes out of valve port.
1. Shut off power to equipment. Shut
off inlet water ahead of system.
5. Feel bowl o-ring; if dry, lubricate
with silicone lubricant.
3. Unscrew bowl.
7. Hand tighten bowl into head.
10. Turn on power to equipment.
for installations in Massachusetts, the commonwealth of Massachusetts plumbing code 248 cMr shall be adhered to. consult your licensed
plumber for installation of the system. this system and its installation must comply with state and local regulations.
Download from Www.Somanuals.com. All Manuals Search And Download.
replAceMent pArtS
System Tested and Certified by NSF International against
NSF/ANSI Standards 42 and 53 for the reduction of:
Contact your local Everpure dealer for filter cartridges or system replace-
ment parts.
Standard No. 42 —
Aesthetic Effects
Chemical Reduction
Taste and Odor
Chlorine
Mechanical Filtration
Particulate Class I: 99.2% reduction of particles
one-half micron and larger in size
Description
part number
EV3114-09
EV3114-07
EV3112-40
EV3112-38
EV3112-39
EV3016-41
EV3112-41
Inlet/outlet pressure gauge
Inlet/flushing valve
O-ring for prefilter or SR-X
Prefilter bowl
Standard No. 53 —
Health Effects
Mechanical Filtration
Turbidity (MC, MC2 only)
Cyst (MC, MC2, XC, XC2 only)
Asbestos (MC, MC2 only)
SR-X bowl
LPA pressure switch
Wrench
liMiteD WArrAnty
coMMerciAl WAter treAtMent equipMent
You have just purchased one of the finest water treatment units made. As an expression of our confidence in Everpure products, this product is warranted against defects in
material and workmanship to the original end-user when installed in accordance with Everpure specifications. The warranty period commences from the date of purchase
and is administered as follows:
for a period of one yeAr
for a period of fiVe yeArS
replaceable elements (i.e., filter & water treatment cartridges)*
the entire system (excluding replaceable elements)
*this is for material & workmanship, not filter or water treatment cartridge life.
The unit must be used in operating conditions that conform to Everpure’s recommended design guidelines. This warranty will not apply if the unit has been modified, repaired
or altered by someone not authorized by Everpure.
if a part described above is found defective within the specified period, you should notify everpure technical service at the phone number listed below. Any part
found defective within the terms of this warranty will be repaired or replaced (at everpure’s discretion) by your local dealer or everpure technical service. you
pay only freight from our factory and local dealer charges. Any repaired or replaced warranty item will be incorporated under the original warranty terms of the
existing system.
We are not responsible for damage caused by accident, fire, flood, freezing, Act of God, misuse, misapplication, neglect, oxidizing agents (such as chlorine, ozone,
chloramines and other related components), alteration, installation or operation contrary to our printed instructions, or by the use of accessories or components which do not
meet Everpure’s specifications. Refer to the specifications section in the Installation and Operating manual for approved application parameters.
Our product performance specifications are furnished with each water treatment unit. TO THE EXTENT PERMITTED BY LAW, EVERPURE DISCLAIMS ALL IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE; TO THE EXTENT REQUIRED BY LAW, ANY SUCH IMPLIED
WARRANTIES ARE LIMITED IN DURATION TO THE PERIOD SPECIFIED ABOVE FOR THE ENTIRE WATER TREATMENT UNIT. As a manufacturer, we do not know the characteristics
of your water supply or the purpose for which you are purchasing this product. The quality of water supplies may vary seasonally or over a period of time, and your water
usage rate may vary as well. Water characteristics can also differ considerably if this product is moved to a new location. For these reasons, we assume no liability for the
determination of the proper equipment necessary to meet your requirements, and we do not authorize others to assume such obligations for us. Further, we assume no
liability and extend no warranties, express or implied, for the use of this product with a non-potable water source or a water source which does not meet the conditions for
use described in the owner’s guide or performance data sheet for this product. OUR OBLIGATIONS UNDER THIS WARRANTY ARE LIMITED TO THE REPAIR OR REPLACEMENT
(AT EVERPURE’S DISCRETION) OF THE FAILED PARTS OF THE WATER TREATMENT UNIT, AND WE ASSUME NO LIABILITY WHATSOEVER FOR DIRECT, INDIRECT, INCIDENTAL,
CONSEQUENTIAL, SPECIAL, GENERAL OR OTHER DAMAGES.
Some states do not allow the exclusion of implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Similarly,
some states do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state. Consult your telephone directory for your local independently operated Everpure dealer, or
write Everpure for warranty and service information.
for sales, replacement components, and service, contact your everpure dealer or:
everpure, llc: 1040 Muirfield Drive • Hanover Park, Illinois 60133 • 800.323.7873
in europe: Toekomstlaan 30 • B-2200 Herentals, Belguim
technical Service
800.942.1153
in Japan: Hashimoto MN Bldg. 7F • 3-25-1 Hashimoto Sagamihara-Shi • Kanagawa 229-1103, Japan
Printed in U.S.A.
EV3112-78 Rev E AP08
Download from Www.Somanuals.com. All Manuals Search And Download.
|