| 	
		 EverFocus   
					Operation Instruction   
					1/3" CCD Standard/High Resolution   
					Digital Color Box Camera   
					EQ200E/300E   
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				Federal Communication Commission Interference   
					Statement   
					This equipment has been tested and found to comply with the limits for a Class A digital device,   
					pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection   
					against harmful interference in a residential installation. This equipment generates, uses and can   
					radiate radio frequency energy and, if not installed and used in accordance with the instructions, may   
					cause harmful interference to radio communications. However, there is no guarantee that   
					interference will not occur in a particular installation. If this equipment does cause harmful   
					interference to radio or television reception, which can be determined by turning the equipment off   
					and on, the user is encouraged to try to correct the interference by one of the following measures:   
					- 
					- 
					- 
					Reorient or relocate the receiving antenna.   
					Increase the separation between the equipment and receiver.   
					Connect the equipment into an outlet on a circuit different from that to which the receiver is   
					connected.   
					- 
					Consult the dealer or an experienced radio/TV technician for help.   
					FCC Caution: Any changes or modifications not expressly approved by the party responsible for   
					compliance could void the user's authority to operate this equipment.   
					This device complies with Part 15 of the FCC Rules. Operation is subject to the following two   
					conditions: (1) This device may not cause harmful interference, and (2) this device must accept any   
					interference received, including interference that may cause undesired operation.   
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				Table of Contents   
					1. Product Overview……………………………………………5   
					1.1 Features................................................................. 5   
					1.2 Accessory Parts List................................................ 6   
					1.3 Specifications......................................................... 7   
					1.4 Dimensions............................................................. 8   
					1.5 Back Panel Overview ............................................... 8   
					1.6 Camera Setting DIP Switch....................................... 9   
					2. Installation…………………………………………………….10   
					2.1 Plug the Power...................................................... 10   
					2.2 Mount the Lens ..................................................... 10   
					2.3 Connect the Video Output....................................... 10   
					2.4 Adjust the Lens ..................................................... 10   
					4 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				H P E  
					C H A P T E R   
					I N S A O  
					1 
					P R O D U C T O V E R V I E W   
					Chapter   
					1 
					Product Overview   
					The new redesigned EverFocus color box camera produces excellent images with 1/3” SONY Super   
					HAD CCD. The EQ series offers cost-effective solutions suitable for all your surveillance   
					applications. The camera includes an adapter ring and it is compatible with both C-mount and   
					CS-mount lenses. In addition, EQ300E/EQ200E provides 24 hours monitoring Day/Night function.   
					Available in high resolution (520TVL) and standard resolution (380TVL).   
					1.1 Features   
					z 
					Low light sensitivity 0.4 Lux/F=1.2(AGC ON) is achieved by using the advanced 1/3” SONY super   
					HAD CCD. (EQ300E)   
					z 
					Low light sensitivity 0.3 Lux/F=1.2(AGC ON) is achieved by using the advanced 1/3” SONY super   
					HAD CCD. (EQ200E)   
					z 
					z 
					z 
					z 
					z 
					z 
					z 
					520 TVL (EQ300E) or 380 TVL (EQ200E) of horizontal resolution   
					Support video drive and DC drive auto IRIS lens   
					Advanced Digital Signal Processor for excellent image quality   
					Day/Night function   
					BLC, AGC and FL On/Off switchable   
					Compatible with both C-mount and CS-mount lens (adapter ring included)   
					System available for NTSC or PAL   
					5 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				H P E  
					C H A P T E R   
					1 
					I N S A O  
					P R O D U C T O V E R V I E W   
					1.2 Accessory Parts List   
					Please be careful when you unpack the box due to the electronics devices inside. Check and make sure   
					that you have all the items listed below inside the original box:   
					z 
					z 
					z 
					Camera unit x 1   
					Operation instructions (this document) x 1   
					Mounting kit includes:   
					  -C adaptor mount ring x 1   
					-L wrench x 1   
					-Iris Lens Connector (top) x 1   
					-Iris Lens Connector (bottom) x 1   
					Please Note: If an item appears to have been damaged in shipment, replace it properly in its carton and   
					notify the shipper. If any items are missing, notify your EverFocus Electronics Corp. Sales Representative or   
					Customer Service. The shipping carton is the safest container in which the unit may be transported. Save it   
					for possible future use.   
					6 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				C H A P T E R   
					1 
					P R O D U C T O V E R V I E W   
					1.3 Specifications   
					Type   
					EQ200E   
					EQ300E   
					Pickup Device   
					Video Format   
					1/3'' SONY Super HAD CCD   
					NTSC or PAL   
					NTSC: 525 TV lines, 60 fields/sec   
					PAL: 625 TV lines, 50 fields/sec.   
					Scanning System   
					Picture Elements   
					510 x 492 (NTSC) ; 500 x 582 (PAL) 768 x 494 (NTSC) ; 752 x 582 (PAL)   
					Horizontal Resolution   
					Sensitivity   
					380 TV Lines   
					0.3 Lux/F=1.2   
					520 TV Lines   
					0.4 Lux/F=1.2   
					S/N Ratio   
					Over 48dB (AGC off)   
					1/50(1/60)~1/100,000   
					Video/Direct Drive switch   
					ON/OFF Switch   
					Electronic Shutter   
					Auto iris   
					Back Light Comp.   
					Auto Gain Control   
					Flickerless   
					ON/OFF Switch   
					ON/OFF Switch   
					Simple Day/Night   
					Auto/OFF Switch   
					Auto White Balance   
					Gamma Correction   
					Video Output   
					Sync. Mode   
					Yes   
					0.45   
					BNC 1.0Vp-p, 75ohm   
					Internal sync   
					C/CS mount   
					Optional   
					Lens Mount   
					Audio   
					Power Source   
					3 types: 12VDC only ; 12VDC/24VAC ; 100VAC~240VAC   
					12VDC: 1.6W max.   
					Power Consumption   
					24VAC: 2.2W max.   
					100VAC~240VAC:1.6W max.   
					Dimensions   
					58mm(W) x 55mm(H ) x 125mm(D) ; 2.3"(W) x 2.2"(H ) x 4.9"(D)   
					0.25kg ; 0.55lbs   
					Weight   
					Operating Temperature   
					Certifications   
					0°C~50°C ; 32°F~122°F (20%~80% Humidity)   
					FCC/CE   
					7 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				C H A P T E R   
					P R O D U C T O V E R V I E W   
					1 
					1.4 Dimensions   
					1.5 Back Panel Overview   
					8 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				C H A P T E R   
					1 
					P R O D U C T O V E R V I E W   
					1.6 Camera Setting DIP Switch   
					1 
					○ DD/VD   
					For video drive auto iris lens, please set switch to VD. For Direct Drive iris lens, set switch to DD.   
					Wire the cable of lens to Mini Plug according to the following table:   
					IRIS   
					Pin1   
					+12V   
					Cnt-   
					Pin   
					GND   
					Cnt+   
					Pin 3   
					VD-IRIS   
					Drv+   
					Pin 4   
					GND   
					Drv-   
					3 
					1 
					4 
					2 
					Video Drive   
					Direct Drive   
					For Direct Drive iris lens:   
					Brightness Level can be adjusted from the IRIS level VR on the back panel.   
					- Turn counterclockwise to L to get darker picture.   
					- Turn clockwise to H to get brighter picture.   
					2 
					○ Electronic Shutter ON/OFF   
					ES ON: The camera continuously adjusts the shutter speed from 1/60 (NTSC), 1/50 (PAL) second   
					to 1/100,000 second according to the luminance conditions of the scene.   
					ES OFF: The shutter speed is fixed at 1/60 (NTSC), 1/50 (PAL) second.   
					Set ES OFF, when auto iris lens is used. Otherwise, turn ES ON for optimum performance.   
					The default setting is ON.   
					3 
					○ BackLight Compensation ON/OFF   
					When BLC is turned on, the AGC, ES and IRIS operating point are determined by averaging over   
					the center area instead of entire field-of-view, so that a dimly-lit foreground object at center area   
					can be clearly distinguished from brightly-lit backgrounds.   
					BLC should not be used unless it is needed to compensate for backlight.   
					The default setting is OFF.   
					Note: When ES setting is OFF, then BLC function will be inactive.   
					4 
					○ Automatic Gain Control ON/OFF   
					AGC ON: The sensitivity increases automatically when light is low.   
					AGC OFF: A low-noise picture is obtained under a low light condition.   
					The default setting is ON.   
					5 
					○ FL (Flickerless) ON/OFF   
					When picture flicker fiercely, turn FL on, then the camera will stabilize the speed of electronic   
					shutter at 1/100(NTSC) or 1/120(PAL) automatically, and reduce the flicker immediately.   
					The default setting is OFF.   
					6 
					○ D/N Auto/OFF   
					Day&Night: When light environment is under 5 Lux, the camera will switch to black and white   
					mode. However, when light environment is over 10 Lux, the camera will switch to color mode.   
					Please be informed that any D/N switch will result a delay of 4~5 seconds.   
					The default setting is OFF.   
					Day&Night OFF: Camera stays in color mode.   
					Note: when AGC setting is OFF, then D/N function will be inactive.   
					9 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				C H A P T E R   
					2 
					I N S T A L L A T I O N   
					Chapter   
					2 
					Installation   
					This chapter will describe, in general terms, how to install the EQ300E/EQ200E camera.   
					STEPS:   
					1. Plug the power   
					2. Mount the lens   
					3. Connect the video output   
					4. Adjust the lens   
					2.1 Plug the Power   
					Plug the power cord to the outlet. Power indicator LED should light if the power source is properly   
					connected.   
					Warning   
					• 
					To prevent electrical shock, turn off the electrical power before making electrical   
					connections.   
					• 
					• 
					• 
					Do not expose the appliance to water or moisture, nor try to operate it in wet areas.   
					Do not connect high voltage power to the camera. It may damage the camera.   
					Do not short circuit the power leads and expose the wire when connecting the power supply   
					to the camera   
					2.2 Mount the Lens   
					i. Remove the cover cap from the top of the lens mount.   
					ii. If C mount lens is used, please fix the C Mount Ring (the 5 mm thick ring attached in the   
					accessory bag) to the top of the lens mount before mounting the lens.   
					iii. Screw the lens firmly onto the lens mount.   
					2.3 Connect the Video Output   
					Connect the video output of the camera to a color monitor or other video device through a 75   
					ohm type coaxial cable with BNC female connector at camera end.   
					10   
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				C H A P T E R   
					2 
					I N S T A L L A T I O N   
					2.4 Adjust the Lens   
					Once the image appears on the monitor, adjust the focus and diaphragm of the lens to obtain the   
					best picture.   
					When a lens does not hold focus at both ends of the zoom range, do back focus adjustment as   
					following:   
					i. Set the focus ring of the lens to infinity position.   
					ii. Take picture of subject at a distance more than 20m away from the camera.   
					iii. Loosen the lens mount fixing screw located at right-hand side of the front panel by using the   
					L wrench.   
					Mounting hole   
					L wrench   
					iv. Turn the lens and the mount together so that the subject is in focus.   
					v. Secure the lens mount fixing screw firmly again.   
					Mount the camera on the mounting bracket by using the mounting hole at bottom or top of the front   
					panel. (Mounting bracket is an optional accessory).   
					11   
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				C H A P T E R   
					2 
					I N S T A L L A T I O N   
					EverFocus Electronics Corp.   
					Head Office:   
					Europe Office:   
					12F, No.79 Sec. 1 Shin-Tai Wu Road,   
					Hsi-Chih, Taipei, Taiwan   
					TEL: +886-2-26982334   
					FAX: +886-2-26982380   
					
					Albert-Einstein-Strasse 1   
					D-46446 Emmerich, Germany   
					TEL: 49-2822-9394-0   
					
					China Office:   
					USA L.A. Office:   
					Room 609, Technology Trade Building,   
					Shangdi Information Industry Base, Haidian   
					District, Beijing,China 10085   
					TEL: +86-10-62973336/37/38/39   
					FAX: +86-10-62971423   
					1801 Highland Ave. Unit A   
					Duarte, CA 91010, U.S.A.   
					TEL: +1-626-844-8888   
					FAX: +1-626-844-8838   
					
					
					USA N.Y. Office:   
					Japan Office:   
					415 Oser Avenue Unit S   
					Hauppauge, NY 11788   
					TEL: 631-436-5070   
					FAX: 631-436-5027   
					
					1809 WBG MARIBU East 18F,   
					2-6 Nakase.Mihama-ku.   
					Chiba city 261-7118, Japan   
					TEL: +81-43-212-8188   
					FAX: +81-43-297-0081   
					
					Your EverFocus product is designed and   
					manufactured with high quality materials and   
					components which can be recycled and   
					reused.   
					Ihr EverFocus Produkt wurde entwickelt und   
					hergestellt mit qualitativ hochwertigen   
					Materialien und Komponenten, die recycelt   
					und wieder verwendet werden können.   
					Dieses Symbol bedeutet, dass elektrische und   
					elektronische Geräte am Ende ihrer   
					Nutzungsdauer vom Hausmüll getrennt   
					entsorgt werden sollen.   
					This symbol means that electrical and   
					electronic equipment, at their end-of-life,   
					should be disposed of separately from your   
					household waste.   
					Please, dispose of this equipment at your   
					local community waste collection/recycling   
					centre.   
					Bitte entsorgen Sie dieses Gerät bei Ihrer   
					örtlichen kommunalen Sammelstelle oder im   
					Recycling Centre.   
					Helfen Sie uns bitte, die Umwelt zu erhalten, in   
					der wir leben!   
					In the European Union there are separate   
					collection systems for used electrical and   
					electronic product.   
					Please, help us to conserve the environment   
					we live in!   
					P/N: MEQ2G01000_Ver.C   
					12   
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				 |