4230-4240 Series
OWNER’S GUIDE
G
u
í
a
d
e
l
PPropieetario
L
e
G
u
i
d
e
d
u
P
r
o
p
r
i
é
t
a
i
r
e
u
r
u
e
k
r
e
k
Before Returning, Call
Eureka Customer Service
Antes de enviar de regreso, Ilame al Servico al Cliente de Eureka
Avant de le retourner, appelez le service à la clientèle Eureka
HELPLINE LÍNEADEAYUDA LIGNE D’AIDE
1-800-282-2886
8 a.m. to 7:30 p.m. (CST), Monday - Friday
10 a.m. to 6:30 p.m. (CST), Saturday - Sunday
8 a.m. a 7:30 p.m. (CST), del lunes a viernes
10 a.m. a 6:30 p.m. (CST), sábado y domingo
8 h à 19 h 30 (CST), lundi au vendredi
10 h à 18 h 30 (CST), samedi et dimanche
Promotional code: 4230ser09
Special Offer – receive 15% off parts and accessories
Upright Vacuum Cleaner
Household Type
Aspiradora vertical
tipo doméstico
Aspirateur vertical
de type résidentiel
when ordering online. Promotion excludes vacuums.
Oferta especial – descuento de 15% cuando compre partes
y accesorios por internet. Oferta excluye aspiradoras.
Offre spéciale
–
recevez 15 % de réduction sur les pièces et les accessoires
lorsque vous commandez en ligne. La promotion exclut les aspirateurs.
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2012 Electrolux Home Care Products, Inc. Printed in China PN83334A
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER
WARNING
To reduce the risk of fire, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
• Do not leave vacuum cleaner when plugged in. Turn off the switch and unplug the
electrical cord when not in use and before servicing.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Use only as described in this manual. Use only manufacturer's recommended attachments.
!
• Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been
dropped, damaged, left outdoors, or dropped into water, return it to a service center before using.
• Do not pull or carry by cord. Do not use cord as a handle. Do not close a door on cord or pull cord
around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord away from
heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Hold plug when rewinding onto cord reel. Do not allow plug to whip when rewinding.
• Do not handle plug or vacuum cleaner with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint,
hair, and anything that may reduce airflow.
• This vacuum cleaner creates suction and contains a revolving brush roll. Keep hair, loose
clothing, fingers, and all parts of body away from openings and moving parts.
• Do not place vacuum cleaner on furniture or stairs as the brush roll may cause damage. Use
extra care when cleaning stairs. Place vacuum cleaner on floor with the handle in storage
position while using attachments.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dust cup, filter and screen, and HEPA exhaust filter in place.
• Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley
when servicing the drive belt.
• Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where
they may be present.
• Store your vacuum cleaner indoors in a cool, dry area.
• Keep your work area well lighted.
• Unplug electrical appliances before vacuuming them.
• Unplug before connecting turbo nozzle.
SAVE THESE INSTRUCTIONS
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully
into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the
proper outlet. Do not change the plug in any way.
Motor
Do Not Oil the motor or the brush roll at any time. The bearings are permanently lubricated
and sealed.
Eureka Customer Service HELPLINE 1-800-282-2886
1
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Identify Parts of Vacuum Cleaner
Telescoping Handle
(on some models)
Cord Retainer
Hose
Hose Hook
Turbo nozzle
Crevice Tool
Dusting Brush
Cord Rewind Button
Filter and Screen
Plug Storage
Carrying Handle
Telescoping Wand
(on some models)
(located inside dust cup)
Hose Connector
Dust Cup
Cord Reel
Wand Retainer
HEPA Filter Compartment
Hose Retainer
Power Switch
ON (I) / OFF (O)
Handle Release
Headlight
(on some models)
Height Adjustment Knob
Brush Roll Cover
Maintenance Schedule
Maintenance Schedule is also located on back side of dust cup.
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. Moving parts! Assemble the vacuum cleaner before using.
!
DUST CUP – Empty after each use
Filter cover
Push button to release bottom lid.
Debris will empty.
Close bottom lid
until it clicks.
FILTER DCF21 – Clean or replace regularly to maintain suction
Filter
DCF21
Empty dust cup. Pull
back latch to lift off lid.
Pull out filter cover,
filter and screen
Brush debris from filter,
cover and screen. Wash and
dry thoroughly, as needed.
Screen
Rinse dust cup;
dry thoroughly.
Reinstall screen,
filter and cover.
Align lid at front; press down
until lid snaps into place.
HEPA FILTER HF11 – Replace within 6 months
HEPA Filter
HF11
Remove dust cup.
Lift up tab on filter cover
and pull off.
Lift out filter
and replace.
BRUSH ROLL – Clean monthly
Brush Roll
EXT-U BELT – Replace worn, cut or out of shape belt
EXT-U Belt
2
Eureka Customer Service HELPLINE 1-800-282-2886
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Features
New features make your vacuum easy to use without bending.
Automatic Cord Rewind
Pull out cord completely. Do not pull past
red line. Press button to rewind cord.
!
Telescoping Handle (on some models)
Push down release button and pull out
handle to desired height.
Carpet Height Adjustment
Use foot to raise or lower. Use the lowest
setting for best cleaning on carpet. If vacuum is hard to push, raise the setting.
Brush roll must reach the carpet for effective cleaning. For bare floors, use bare floor setting.
How to Use Accessories
Handle must be in upright position.
Replace end of wand into wand retainer after using accessories.
!
Telescoping Wand (on some models)
Twist coupling and pull out wand to desired
length; twist to lock. Push tool onto wand.
Crevice Tool
Use for baseboards and corners.
Dusting Brush
Use for furniture, drapes and vents.
Bare Floor Nozzle and Wand
(with some models or available for purchase)
Use for bare floors.
Turbo Nozzle and Stair Hose
(with some models or available for purchase)
Use for furniture and stairs.
Make sure vacuum is below you,
pushed against the bottom step.
1) If model has additional stair hose, attach
to end of wand.
2) Attach turbo nozzle to the end of wand
or hose.
NOTE: Hose length can be increased by
releasing the hose from the hose retainer
on back of unit. Reposition hose inside
hose retainer after using accessories.
Eureka Customer Service HELPLINE 1-800-282-2886
3
Download from Www.Somanuals.com. All Manuals Search And Download.
How to MaintainYour Vacuum Cleaner
!
Make sure vacuum cleaner is turned off and power cord is unplugged.
Maintain Brush Roll
Motor can become hot with normal use.
Do not remove end caps. Remove hair and threads from brush roll periodically.
Check EXT-U Belt. Replace if worn, cut or out of shape.
Avoid touching the motor shaft when checking brush roll or belt.
!
How to replace brush roll or belt
1) Use handle release to lower handle flat
onto floor (Fig. 1).
2) Remove 4 screws from brush roll cover.
(Fig. 2).
Fig. 1
Fig. 2
Fig. 4
Fig. 6
3) Lift off brush roll cover. (Fig. 3).
4) Remove brush roll and belt. Thread new
belt around motor shaft and brush roll
(Fig. 4).
5) Insert left end of brush roll first. Make
sure end cap fits into base. Pull right
side of brush roll to stretch belt and
insert right end cap into base (Fig. 5).
Fig. 3
Make sure it slides into position.
6) Rotate brush roll 2 turns to center belt.
7) Replace brush roll cover (Fig. 3).
8) Replace 4 screws (Fig. 6).
Fig. 5
Change Light Bulb (on some models)
Make sure vacuum is turned off and power cord is unplugged.
!
1) Remove dust cup. Remove HEPA cover
and filter (Fig 7).
2) Unscrew the lens and remove old bulb.
Replace with bulb rated 12 v., 10 w.,
Type 904.
3) Push in new bulb (Fig. 8). Replace lens
cover and replace screw.
4) Replace HEPA filter and cover.
Replace dust cup.
Fig. 7
Fig. 8
4
Eureka Customer Service HELPLINE 1-800-282-2886
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Clear a Blockage
Make sure vacuum is turned off and power cord is unplugged.
!
Hose Blockage
1) Remove hose from hose retainer. Flexing
the hose will loosen any blockage (Fig. 1).
2) Base hose – remove 4 screws and brush
roll cover. Clear blockage from base hose
and check for debris in brush roll. Replace
screws and cover (Fig 2).
C
3) Hose connector – remove dust cup and
remove debris from hose connector
opening. If still blocked, remove screw
from hose connector and remove
blockage (Fig. 3).
C
Fig. 1
Fig. 2
Fig. 3
The Eureka Limited Warranty
Eureka warrants this vacuum cleaner to be free from
defects in material and workmanship for a term of two
years for normal household use. Warranty is granted
only to the original purchaser and members of
immediate household.
Authorized Warranty Station or Service Information, visit
www.eureka.com, write or telephone toll free:
USA: 1-800-282-2886
Electrolux Home Care
North America Service Division
P.O. Box 3900
Mexico: (55) 5343-4384 Canada: 1-800-282-2886
Electrolux Home Care
Electrolux Home Care
North America Service Division
5855 Terry Fox Way
Peoria, IL 61612
Mississauga, Ontario L5V 3E4
This warranty is good for two years from the date of
purchase only when the vacuum cleaner is used in
the accordance with Eureka operating instructions.
Note: refurbished or remanufactured products
have a one year limited warranty.
Obtaining Warranty Service
OutsideYour Community
You must pay the shipping charges to the Eureka
Authorized Warranty Station.
This Warranty Does Not Cover
• Parts of the vacuum that require replacement under
normal use such as disposable dust bags, filters,
drive belts, light bulbs, brush roll, bristles, impellers
and cleaning.
Return Shipping Charges will be paid by the Warranty
Station. When returning parts for repair, please include the
model, type and serial number located on the rating plate
on the lower backside of the vacuum.
• Damages or malfunctions caused by negligence,
abuse, and use not in accordance with the
Owner’s Guide.
Further Limitations and Exclusions
Any warranty that may be implied in connection with your
purchase or use of the vacuum, including any warranty of
Merchantability or any warranty for Fitness For A
Particular Purpose is limited to the duration of this
warranty. Some states do not allow limitations on how long
an implied warranty lasts, so the above limitations may not
apply to you.
• Defects or damages caused by unauthorized
service or the use of other than Genuine Eureka,
ARM & HAMMERTM and FiltreteTM by 3M parts.
What Eureka Will Do
Your relief for the breach of this warranty is limited to
the relief expressly provided above. In no event shall the
manufacturer be liable for any consequential or incidental
damages you may incur in connection with your purchase
or use of the vacuum.
Eureka will, at its option, repair or replace a defective
vacuum or vacuum part that is covered by this warranty.
As a matter of warranty policy, Eureka will not refund
the consumer’s purchase price.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
Warranty Registration
Please fill out and return the warranty registration card
accompanying your vacuum.
This warranty gives you specific legal rights.You may
also have other rights, which may vary by state.
The ARM & HAMMER name is a trademark of Church and Dwight Co., Inc.
3M and Filtrete are trademarks of 3M Company, used by Electrolux Home Care
Products, Inc. under license.
Obtaining Warranty Service
To obtain warranty service you must return the vacuum
or vacuum part along with “proof of purchase” to any
Eureka Authorized Warranty Station. For Eureka
Eureka Customer Service HELPLINE 1-800-282-2886
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Thermal Cut-Off
This vacuum cleaner has a special thermostat that protects the vacuum in case of motor overheating. If the vacuum
suddenly shuts off, push the power switch to off and unplug the vacuum. Check the vacuum for a possible source of
overheating such as a full dust cup, blocked hose or clogged filter. If these conditions are found, fix them and wait at least
30 minutes before attempting to use the vacuum. After the 30 minute period, plug the vacuum back in and turn on the
switch. If the vacuum still does not work, take it to a Eureka authorized service center for repair or call 1-800-282-2886.
Problem Solving
!
Make sure vacuum is turned off and power cord is unplugged.
Solution
Problem
Cause
Power plug
Motor will not start.
• Push plug securely into outlet, try another outlet or
check circuit breaker.
• Step on power switch to turn vacuum on.
• See above.
Power switch
Thermal cut-off
• Empty dust cup, clean and/or change filter.
• Clean or replace filters regularly to maintain suction. Page 2
Vacuum does not clean
carpet or bare floor.
Dust cup and filter
• If picking up fine dust, the dust cup may not look full, but a
fine substance tends to reduce suction when it blocks air flow
through the filter and screen. Refer to page 2 for filter
maintenance. Make sure filter, screen and dust cup are
installed properly.
Belt
• Replace a worn, cut or out of shape belt. Page 4
Hose
• Remove clogs from the hose that restrict the airflow. Make
sure hose is replaced into hose retainer. Page 5
Bare floor setting
Carpet height setting
Dust cup and filter
• For bare floor cleaning, turn height adjustment knob to bare
floor position.
• Turn height adjustment knob to another position.
No suction at the
end of hose.
• Empty dust cup, clean and/or change filter.
• Clean or replace filters regularly to maintain suction. Page 2
• If picking up fine dust, the dust cup may not look full, but a
fine substance tends to reduce suction when it blocks air flow
through the filter and screen. Refer to page 2 for filter
maintenance. Make sure filter, screen and dust cup are
installed properly.
Hose
• Remove clogs from the hose that restrict the airflow. Make
sure hose is replaced into hose retainer. Page 5
Turbo nozzle will not turn.
Rotating brush
• Check turbo nozzle for debris.
Vacuum is hard
to push.
Vacuum height setting
• Adjust knob to a higher position.
Belt
Belt
• Replace a worn, cut or out of shape belt. Page 4
Burning smell; brush roll
will not turn.
• Check brush roll for debris. Page 4
• Replace broken or out of shape belt. Page 4
Cord will not
rewind fully.
Cord tangles
• Pull cord out and rewind. Page 3
6
Eureka Customer Service HELPLINE 1-800-282-2886
Download from Www.Somanuals.com. All Manuals Search And Download.
|