Elation Professional Work Light 575B User Manual

Design Spot 575B  
Elation Professional  
6122 S. Eastern Ave  
Los Angeles, Ca. 90040  
Rev. 11/24/2009  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
CONTENTS  
1. General Information……………………………………………………………………… 4  
a. Introduction………………………………………………………………………. 4  
b. Customer Support…………………………………………….………………… 3  
c. Warranty Registration……………………………………………………..……. 5  
d. Discharge Lamp Warning………………………………………………………. 5  
2. Safety Instructions………………………………………………………........…………. 7  
3. Features……………………………………………………………………………………9  
4. General Guidelines………………………………………………………………………. 10  
5. Lamp Installation…………………………………………………………………………. 11  
a. Lamp installation…………………………………………………….………….. 11  
b. Lamp optimization……………………………………………………..…………12  
6. Mounting and Installation………………………………………………………….……. 14  
a. Mounting Positions……………………………………………………………… 14  
b. Mounting Points…………………………………………………………………. 15  
c. Securing………………………………………………………………………….. 16  
7. Understanding DMX……………………………………………………………………... 17  
a. DMX Linking……..………………………………………………………………. 17  
b. DMX Cable Requirements..……………………………………………………. 17  
c. DMX Termination………..………………………………………………………. 19  
d. DMX Addressing………………………………………………………………… 19  
8. Fixture Menu……………………………………………………………………………… 21  
a. Menu functions………………………………………………………………….. 23  
9. Menu Functions.…………………………………………………………………………. 24  
10. DMX Addressing…………………………………………………………………………. 32  
11. Operation…………………………………………………………………………………. 34  
12. Working with Built-In Programs……………………………………………………...…. 36  
13. DMX Channel Traits………………………………………………………………..….… 39  
14. Fuse Replacement………………………………………………………………………..43  
15. Error Codes………………………………………………………………………………..44  
16. Cleaning and Maintenance……………………………………………………………47  
17. Warranty…………………………………………………………………………………... 48  
18. Photometric Data………………………………………………………………………… 50  
19. Gobo Patterns……………………………………………………………..……………... 51  
20. Dimensional Drawings………………………………………………….……………….. 52  
21. Circuit Schematic………...……………………………………………………………….53  
22. Technical Specifications…………………………………………...………….………… 54  
©Elation Professional, Los Angeles CA.  
3
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
1. GENERAL INFORMATION  
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and  
reliable lighting fixtures on the market today! The Design Spot 575B,™ has been designed to  
perform reliably for years when the guidelines in this booklet are followed. Please read and  
understand the instructions in this manual carefully and thoroughly before attempting to  
operate this unit. These instructions contain important information regarding safety during  
use and maintenance.  
UNPACKING: Thank you for purchasing the Design Spot 575B™ by Elation Professional®  
.
Every Design Spot 575B™ has been thoroughly tested and has been shipped in perfect  
operating condition. Carefully check the shipping carton for damage that may have occurred  
during shipping. If the carton appears to be damaged, carefully inspect your unit for damage  
and be sure all accessories necessary to operate the unit have arrived intact. In the event  
damage has been found or parts are missing, please contact our customer support team for  
further instructions. Please do not return this unit to your dealer without first contacting  
customer support at the number listed below.  
CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to provide  
set up help and to answer any question should you encounter problems during your set up or  
comments or suggestions. For service related issue please contact Elation Professional®  
.
Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.  
Voice:  
Fax:  
(323) 582-3322  
(323) 832-9142  
E-mail:  
Forum:  
Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to  
rain or moisture.  
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs  
yourself, doing so will void your manufactures warranty.  
©Elation Professional, Los Angeles CA.  
4
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
Please do not discard the shipping carton in the trash, keep for warranty repair. Please  
recycle whenever possible.  
WARRANTY REGISTRATION: The Design Spot 575B™ carries a two year (730 days)  
limited warranty. Please fill out the enclosed warranty card to validate your purchase. All  
returned service items whether under warranty or not, must be freight pre-paid and  
accompany a return authorization (R.A.) number. The R.A. number must be clearly written on  
the outside of the return package. A brief description of the problem as well as the R.A.  
number must also be written down on a piece of paper and included in the shipping container.  
If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items  
returned without a R.A. number clearly marked on the outside of the package will be refused  
and returned at customer’s expense. You may obtain a R.A. number by contacting customer  
support at (323) 213-4593.  
DISCHARGE LAMP WARNING: This fixture is fitted with a discharge  
lamp, which is highly susceptible to damage if improperly handled.  
Never touch the lamp with your bare hands, as the oil from your hands  
will shorten lamp life. Also, never move the fixture until the lamp has  
had ample time to cool. Remember, lamps are not covered under  
warranty conditions.  
UV RADIATION: This fixture emits intense UV radiation, which is harmful to the eyes and  
skin. The intense luminance of the lamp can cause severe damage to the retina. Never  
operate this fixture with the protective covers removed, these covers have been specially  
designed to shield against UV radiation.  
Epileptic Warning: Those suffering from epilepsy should avoid looking directly into the lamp  
at all times.  
Avoid switching the fixture on and off repeatedly in short intervals, as this will reduce lamp life  
and intensity.  
To achieve the intensity associated with discharge lamps, these lamps use a gas sealed in a  
©Elation Professional, Los Angeles CA.  
5
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
high-pressure environment to emit a brilliant output. Due to the high pressure involved with  
the construction of the lamp, the lamp may explode during prolonged extensive use. This risk  
is increased with age; added care is encouraged when dealing with older lamps. Thus, lamp  
should always be replaced at the end of their recommended duty cycle. Extreme caution  
should be used when operated this or any fixture fitted with a gas discharge lamp.  
Never open this fixture while in use!  
During the initial operation of this fixture, a light smoke or smell may emit from the interior of  
the fixture. This is a normal process and is caused by excess paint in the interior of the casing  
burning off from the heat associated with the lamp and will decrease gradually over time.  
This device falls under protection-class 1. Therefore it is essential that the device be  
grounded properly.  
Only qualified personnel should perform all electrical connections.  
Be sure the available voltage matches the voltage requirements of the unit.  
Be sure the power cord is never crimped or damaged. If the power cord is damaged, replace  
it immediately with a new one of similar power rating.  
Always disconnect from main power before performing any type of service or any cleaning  
procedure.  
Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of  
the cord.  
Please be aware that damages caused by manual modifications to the device are not  
subject to warranty.  
©Elation Professional, Los Angeles CA.  
6
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
2. SAFETY INSTRUCTIONS  
The Design Spot 575B™ is an extremely sophisticated piece of  
electronic equipment. To guarantee a smooth operation, it is  
important to follow the guidelines in this manual. The  
manufacturer of this device will not accept responsibility for  
damages resulting from the misuse of this fixture due to the  
disregard of the information printed in this manual.  
1. Always be sure that the fan and the air inlets remain clean and are never blocked.  
Allow about 6” (15cm) between this fixture and other devices or a wall to allow for  
proper cooling.  
2. Never touch the fixture during normal operation. This can cause severe personal  
injuries and/or damage to the fixture.  
3. Be sure to unplug the Design Spot 575B™ from the power outlet before performing  
any service related issues.  
4. Lamp Replacement; Allow at least 30 minutes after disconnecting main power  
before you open the Design Spot 575B™. To prevent personal injury, never touch  
the lamp if you are not absolutely sure it has cooled.  
5. Never look directly into the lamp beam. You risk injury to your retina, which may  
induce blindness.  
6. Be sure to track and record the lamp running time. The lamp should be changed at  
the end of the specified lamp life, regardless of lamp output. You may also have to  
change the lamp if it shows any deformations or damage. The same is with all glass  
components, color filters, lenses and mirrors.  
7. For safe operation, follow the Installation guide described in chapter five of this  
manual. Operating the Design Spot 575B™ without suited safety aids such as  
safety cables or clamps can increase the risk of damage and/or personal injury.  
8. Qualified and certified personnel should only perform installation.  
9. When mounting this fixture, use only the original rigging parts included with this  
fixture. Any structural modification will void the original manufactures warranty and  
©Elation Professional, Los Angeles CA.  
7
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
may increase the risk of damage and/or personal injury.  
10. To reduce the risk of fire or electric shock, do not expose this fixture to rain or  
moisture.  
11. Do not attempt to operate this fixture if the power cord has become damaged or  
frayed.  
Important Notice: Damages resulting from the disregard of safety and general user  
instructions found in this user manual are not subject to any warranty claims.  
©Elation Professional, Los Angeles CA.  
8
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
3. FEATURES  
Pan 630°or 540˚ (User selectable) / Tilt 265°  
Built-In Macros (Gobo, Prism)  
3 operation mode: DMX Controlled, Stand-Alone or Sound Activated  
Color Wheel: 8 colors plus white (including UV, CTC, and CTO filters)  
Easy to Navigate On-Board LCD Menu (may be turned 180°)  
Two Gobos Wheels:  
o Wheel 1) Rotating gobo wheel with 6 rotating gobos plus open, all gobos can be  
easily replaceable and gobo indexing  
o Wheel 2) Fixed gobo wheel with 6 rotating gobos plus open  
Strobe Effect: 0~10 flashes per second or random strobe  
Motorized Focus (Near to Far)  
Prism and Prism Rotation, with 16 prism macros (Indexable)  
Bright Phillips MSR 575/2 Lamp (575w / 7200K / 1000Hrs / 43,000Lm)  
Linear Dimmer from 0%~100%  
RDMX (Remote DMX addressing from any DMX console)  
Auto test for all functions  
Automatic Pan/Tilt Correction  
Built-in Iris (5% ~ 100% - Seamless), with Iris Pulse Effect  
Glass Dichroic Reflector for Even Lamp Output  
USITT DMX-512 Compliant  
o 15 DMX Channels (16bit Operation)  
o 13 DMX Channels (8bit Operation)  
o 20 DMX Channels (Extended)  
10 User Assignable Program Presets - Internal Program: Edit and save programs to  
the incorporated EPROM. Maximum of 64 scenes.  
©Elation Professional, Los Angeles CA.  
9
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
4. GENERAL GUIDELINES  
This fixture is a professional lighting effect designed for use on stage, in nightclubs, in  
theatres, etc. Do not attempt operation or installation without a proper knowledge on how to  
do so.  
This fixture was designed for indoor use only.  
Consistent operational breaks may ensure that the fixture will function properly for many  
years to come.  
Do not shake the fixture around. Avoid brute force when installing or operating the device.  
While choosing an installation location, please be sure that the fixture will not be exposed to  
extreme heat, moisture or dust. The minimum distance between the fixture and a wall or flat  
surface should be at least 0.5 meter (about 1.5ft).  
Always install the fixture with an appropriate safety cable. When installing the fixture in a  
suspended environment always be sure to use mounting hardware no less than M10 x 25  
mm, also be sure the hardware is insert in the pre-arranged screw holes in the base of the  
fixture.  
When using the quick release “Omega” cam-lock system, be sure the four quick lock  
fasteners are locked in the quick lock holes correctly.  
Do not attempt to operate this fixture until you have familiarized yourself with its functions.  
Do not permit operation by persons not qualified for operating this type of theatrical fixture,  
most damages are the result of operations by nonprofessionals.  
If possible, please use the original packaging to transport the fixture in for service.  
©Elation Professional, Los Angeles CA.  
10  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
5. LAMP INSTALLATION INSTRUCTIONS  
For a proper and safe lamp change, please read this chapter carefully and follow all  
instructions.  
Safety Regulations  
Disconnect the unit’s main power supply.  
Allow the unit to cool for at least 30 minutes before attempting any type of service.  
Before you put the Design Spot 575B™ into operation be sure all covers have been  
replaced, otherwise you risk damage to the retina and expose to UV radiation!  
Replace the lamp with an approved replacement type. Be sure to follow all the lamp  
handling procedures included with your new lamp. Never handle the new lamp with  
your bare hands as the oils from your skin may damage the lamp. Always replace  
with a lamp that meets the original lamp specification, failure to do so may damage  
the unit and will void your manufactures warranty.  
Installation Procedure:  
1. Set the fixture on a flat surface and remove the four screws labeled “A” “B,” “C,” and  
“D” found on the back plate of the head assembly.  
2. Gently pull out the lamp/socket assembly to access the lamp.  
3. Gently remove the old lamp by grasping it by metal ends.  
4. Insert the new lamp securely, locking the lamp in place as illustrated in the diagram  
on the next page. Orientate the lamp filler tube towards the backside of the reflector.  
Before reassembling the unit, be sure the new lamp is securely seated in the lamp  
socket. Always be sure to only use specified lamp types! (MSR 575 lamp or  
equivalent).  
©Elation Professional, Los Angeles CA.  
11  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
OK  
NO  
5. Once the lamp has been inserted into the socket, gently slide the socket assembly  
back into place and secure with the four retaining screws.  
6. Reset the lamp run time in the system menu.  
7. Always be sure to optimize the lamp after lamp replacement.  
Do not operate this device with open cover  
Lamp Optimization  
The lamp orientation and optimization must be adjusted after every lamp change. This  
procedure centers the lamp in the reflector. Proper optimization will increase lamp life and  
ensure a bright, crisp, and even output. Improper optimization may add a yellow tint to the  
lamp output and reduce intensity. The minimum deviation amount is 1.0mm. Running the  
fixture within a lower deviation can cause damage to the lamp and/or lens.  
The Design Spot 575B™ lamp holder is aligned at the factory. However, due to slight  
imperfections in all lamps, fine adjustments will improve light performance. Please follow the  
procedure below for proper lamp optimization:  
1. Using either a DMX controller or the control panel on the unit, strike the lamp and focus  
the light on a flat surface (beam open, white, no gobo, no effect).  
2. Center the hot-spot (the brightest part of the beam) using the 3 adjustment screws  
labeled 1, 2, and 3 as illustrated on the next page. Turn one screw at a time to drag the  
hot-spot diagonally across the projected image. If you cannot detect a hot-spot, adjust  
the lamp until the light is even.  
3. To reduce a hot-spot, pull the lamp in by turning all three screws clockwise a 1/4-turn  
©Elation Professional, Los Angeles CA.  
12  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
at a time until the light is evenly distributed.  
4. If the light is brighter around the edge than it is in the center, or if light output is low, the  
lamp is too far back in the reflector. "Push” the lamp out by turning each of the  
adjustment screws (  
counterclockwise. Turn until the light is bright and evenly  
"1, 2, 3”)  
distributed throughout the beam field.  
Please remember that a MSR 575 lamp is not a hot-strike lamp therefore, you must wait  
approximately 15 minutes before you can attempt to strike the lamp once it has been turned  
off.  
©Elation Professional, Los Angeles CA.  
13  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
6. MOUNTING AND INSTALLATION  
Cautions:  
For added protection mount the fixtures in areas outside walking paths, seating areas, or in  
areas were unauthorized personnel might reach the fixture.  
Before mounting the fixture to any surface, make sure that the installation area can hold a  
minimum point load of 10 times the device’s weight.  
Fixture installation must always be secured with a secondary safety attachment, such as an  
appropriate safety cable.  
Never stand directly below the device when mounting, removing, or servicing the fixture.  
Before taking into operation for the first time,  
the installation has to be approved by an expert.  
When installing the device, make sure there is no highly  
inflammable material within a distance of min. 0,5m  
Mounting  
The Design Spot 575B™ is fully operational in two different mounting positions, hanging  
upside-down from a ceiling, or set on a flat level surface (see illustration on next page). Be  
sure this fixture is kept at least 0.5m (1.5ft) away from any flammable materials (decoration  
etc.). Always use and install the supplied safety cable as a safety measure to prevent  
accidental damage and/or injury in the event the clamp fails.  
Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE0711-217  
for proper installation in Europe To ensure proper installation, only  
qualified staff should attempt installation.  
©Elation Professional, Los Angeles CA.  
14  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
Mounting points  
Overhead mounting requires extensive experience, including amongst others calculating  
working load limits, a fine knowledge of the installation material being used, and periodic  
safety inspection of all installation material and the fixture. If you lack these qualifications, do  
not attempt the installation yourself. Improper installation can result in bodily injury.  
CAUTION!  
Be sure a qualified electrician performs all electrical  
connections.  
Be sure to complete all rigging and installation procedures before connecting the main power  
cord to the appropriate wall outlet.  
Clamp Mounting  
The Design Spot 575B™ provides a unique mounting bracket assembly that integrates the  
hanging yoke as well as the safety cable rigging point in one unit (see the illustration on the  
next page). When mounting this fixture to truss be sure to secure an appropriately rated  
clamp to the hanging yoke using a M10 screw fitted through the center hole of the hanging  
©Elation Professional, Los Angeles CA.  
15  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
yoke. As an added safety measure be sure to attached at least one properly rated safety  
cable to the fixture using on of the safety cable rigging point integrated in the bracket  
assembly  
Securing the Design Spot 575B™  
Regardless of the rigging option you choose for your Design Spot 575B™ always be sure to  
secure your fixture with a safety cable. The fixture provides a built-in rigging point for a safety  
cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging  
point for the safety cable and never secure a safety cable to a carrying handle.  
©Elation Professional, Los Angeles CA.  
16  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
7. UNDERSTANDING DMX  
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting  
and controller manufactures as a form of communication between intelligent fixtures and  
controllers. DMX allows all makes and models of different manufactures to be linked together  
and operate from a single controller. This is possible as long as all the fixtures and the  
controller are DMX compliant. ADMX controller sends the DMX data instructions to the fixture  
allowing the user to control the different aspects of an intelligent light. DMX data is sent out as  
serial data that travels from fixture to fixture via data “IN” and data “OUT” XLR terminals  
located on the fixtures (most controllers will only have output jacks).  
DMX Linking: To ensure proper DMX data transmission always use proper DMX cables and  
a terminator. When using several DMX fixtures try to use the shortest cable path possible.  
Never split a DMX line with a “Y” style connector. The order in which the fixtures are  
connected in a DMX line does not influence the DMX addressing. For example; a fixture  
assigned a DMX address of 1 may be placed anywhere in the DMX chain, at the beginning, at  
the end, or anywhere in the middle. The DMX controller knows to send data assigned to  
address 1 to that fixture no matter where it is located in the DMX chain. The Design Spot  
575B™ can be controlled via DMX-512 protocol. The Design Spot 575B™ is a 15-channel  
DMX fixture. The DMX address is set electronically using the controls on the LCD menu.  
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): Your  
fixture and your DMX controller require a standard 3-pin or 5-pin XLR connector for data input  
and data output (the figure below is of a 3-Pin XLR connector). If you are making your own  
cables, be sure to use two conductor shielded digital DMX cable rated at 120 ohms; this cable  
is designed for DMX transmission and may be purchased from your Elation dealer or at most  
professional lighting retailers. Your cables should be made with a male and female XLR  
connector on either end of the cable. A DMX line must be daisy chained and cannot be split,  
unless using an approved DMX splitter such as the Elation Opto Branch 4™ or DMX  
Branch/4™.  
©Elation Professional, Los Angeles CA.  
17  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
Be sure to follow the above figure when making your own cables. Do not use the ground lug  
on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow  
the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield  
could cause a short circuit and erratic behavior.  
DMX-512 control connection  
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the  
other side to the male 3-pin XLR input of the moving head (Please refer to the diagram  
below.). You can chain multiple moving heads together through serial linking. The cable that  
should be used is two conductor, shielded DMX cable with XLR input and output connectors.  
Remember to daisy chain your “in” and “out” data connections, never split or “Y” your DMX  
connections unless you are using an approved DMX splitter such as the Elation Opto Branch  
4™ or DMX Branch/4™.  
©Elation Professional, Los Angeles CA.  
18  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
DMX-512 connection with DMX terminator  
A DMX terminator should be used in all DMX lines especially in longer runs. The use of a  
terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt  
resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA  
-). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to  
terminate the line. Using a line terminator (Elation part: DMX T PACK) will decrease the  
possibilities of erratic behavior.  
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA  
transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX  
line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be  
used, these adaptors are readily available at most electric stores. The following chart details  
a proper cable conversion.  
Fixture DMX addressing;  
All fixtures should be given a DMX starting address when using a DMX controller, so the  
correct fixture responds to the correct control signal. This digital starting address is the  
©Elation Professional, Los Angeles CA.  
19  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
channel number from which the fixture starts to “listen” to the digital control information sent  
out from the DMX controller. The allocation of this starting DMX address is achieved by  
setting the correct DMX address on the digital display located on the head of the fixture.  
You can set the same starting address for all fixtures or a group of fixtures, or set different  
address for each individual fixture. Be advised that setting all you fixtures to the same DMX  
address will subsequently control all fixtures in the same fashion, in other words, changing  
the settings of one channel will affect all the fixtures simultaneously.  
If you set each fixture to a different DMX address, each unit will start to “listen” to the channel  
number you have set, based on the quantity of control channels (DMX channels) of each  
fixture. That means changing the settings of one channel will only affect the selected fixture.  
In the case of the Design Spot 575B™, which is a 15 channel fixture, you should set the  
starting DMX address of the first unit to 1, the second unit to 16 (15 + 1), the third unit to 31  
(15 + 16), and so on.  
Note: During start-up the Design Spot 575B™ will automatically detect whether a DMX data  
signal is being received or not. If DMX data signal is being received, the display will show  
"Addr=XXX" (XXX representing the actual DMX address). If the fixture is not receiving a  
DMX signal the display will flash. If your fixture is connected to a DMX controller and the  
display is flashing (not receiving a DMX signal), please check the following:  
-
The 3-PIN or 5-PIN XLR input plug (cable with DMX signal from controller) is not  
connected or is not inserted completely into the DMX input jack of the fixture.  
The DMX controller is switched off or defective.  
-
-
-
The DMX cable or connector is defective.  
A DMX terminator has been inserted into the last fixture in your DMX chain.  
©Elation Professional, Los Angeles CA.  
20  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
8. FIXTURE MENU  
On-Board System Menu: The Design Spot 575B™ comes with an easy to navigate system  
menu. This next section will detail the functions of each command in the system menu.  
LCD Control Panel: The control panel located on the side of the fixture allows you to access  
the main menu and make necessary adjustments to the Design Spot 575B™. During normal  
operation, tapping the “MODE/ESC” key once will access the fixture’s main menu. Once in  
the main menu you can navigate through the different functions and access the sub-menus  
with the Up and Down buttons. Once you reach a field that requires adjusting, tap the  
ENTER button to activate that field and use the UP and Down button to adjust the field.  
Tapping the Enter button once more will confirm your setting. You may exit the main menu at  
any time without making any adjustments by tapping the MODE/ESC button.  
Set DMX Address  
Value Display  
Set To Slave  
A001~AXXX  
PAN……  
DMX address setting  
DMX value display  
Slave setting  
Slave1,Slave2,Slave3  
Master / Alone  
Master / Alone  
Auto Program  
Music Control  
Time Information  
Auto program  
Music control  
Current Time  
XXXX(Hours)  
XXXX(Hours)  
XXXX(Hours)  
XXXX(Hours)  
XXXX(Minute)  
Password=XXX  
ON/OFF  
Power on running time  
Fixture running time  
Fixture Last times clear  
Lamp running time  
Lamp off time  
Total Life Hours  
Last Run Hours  
Lamp Hours  
Lamp Off Time  
Timer Password  
Clear Last Run  
L-Timer Password  
Clear Lamp Time  
Timer Password 038  
Clear Fixture Last time  
Password=XXX  
ON/OFF  
Lamp  
Password  
Code=”038”  
Clear lamp time  
Temperature Info  
Software Version  
Lamp On or Off  
Head Temperature  
Ver1.0……  
ON/OFF  
XXX /  
Temperature in the head  
Software version of each IC  
Lamp on/off  
Automatic La-On  
Lamp On Via DMX  
Lamp Off Via DMX  
Lamp Off No DMX  
Lamp On at Temp.  
Lamp Off at Temp.  
ON/OFF  
Lamp on/off when Power on  
Lamp on via DMX  
Lamp off via DMX  
Lamp off if no DMX  
Lamp restart at temp.  
Lamp off at temp.  
ON/OFF  
ON/OFF  
OFF, 0FF~19M  
20~79 ,45 /68~174 113  
80 139 130 /176~282 , 266  
~
,
©Elation Professional, Los Angeles CA.  
21  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
Status Settings  
Address via DMX  
No DMX Status  
Pan Reverse  
ON/OFF  
Add. via DMX  
Close/Hold/Auto/Music  
ON/OFF  
Auto run if no DMX  
Pan Reverse movement  
Tilt Reverse movement  
Pan Degree Select  
Tilt Reverse  
ON/OFF  
Pan Degree  
630/540  
Feedback  
ON/OFF  
Movement Feedback switch  
Movement Mode Select  
Sensitivity of Mic.  
Movement Speed  
Mic Sensitivity  
Service Password  
Fan Voltage  
Speed 1~ 4  
0~99%  
Service Setting  
Fans Control  
Password=XXX  
High/Low  
Service Code“=050”  
Fan Voltage Select  
Gobo Speed  
Quick/Slow  
Gobo Change Speed  
Fans Speed Mode Select  
Auto Fans Speed  
High Fans Speed  
Low Fans Speed  
Shutoff Time  
Display Setting  
Display shutoff time  
Temperature C/F Celsius  
Fahrenheit  
PAN……  
Temperature  
between  
switch  
/
Initial Effect  
Reset Default  
Reset All  
PAN =XXX  
Initial effect position  
Restore factory set.  
Reset all motors  
Reset Pan/Tilt  
ON/OFF  
Reset Pan&Tilt  
Reset Colors  
Reset Gobos  
Reset Shutter  
Reset Others  
Reset color wheel  
Reset gobos  
Reset shutter and/or dimmer  
Reset other motors  
Test Channel  
PAN ……  
Test function  
Manual Control  
PAN  
PAN =XXX  
Fine adjustment of the lamp  
:
:
Calibrate Values  
User Mode  
--Password--  
Color wheel  
:
Password=XXX  
Calbrate and adjust the  
effects to standard/right  
position Password “050”  
User’s mode to change  
channel numbers  
Color wheel=XXX  
:
Standard Mode  
Basic Mode  
Extended Mode  
User Mode A  
User Mode B  
User Mode C  
Max Channel  
PAN  
Edit User Mode  
Select Programs  
Max Channel = XX  
Preset User modes  
PAN = CH01  
:
:
Auto Pro Part 1  
Auto Pro Part 2  
Auto Pro Part 3  
Program 1 ~ 10 Program 1  
Program 1 ~ 10 Program 2  
Program 1 ~ 10 Program 3  
Select programs to be run  
©Elation Professional, Los Angeles CA.  
22  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
Edit Program  
Edit Scenes  
Program 1  
:
Program Test  
Step 01=SCxxx  
Step 64=SCxxx  
Pan,Tilt,……  
(“STEP XX”) Testing program  
Program in loop  
Save and exit  
Program 10  
Edit Scene 001  
Pan=xxx…… Save and automatically  
~ Edit Scene 250 --Secne Time--  
Input By Outside  
TIME=xx.xs  
return  
manual scenes edit  
Automat. scenes rec  
Rec. Controller  
XX~XX  
©Elation Professional, Los Angeles CA.  
23  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
9 MENU FUNCTIONS:  
9.1 Function Mode  
9.1.1. DMX address setting  
This function is used to set or adjust the fixture’s starting DMX address. Every device  
controlled by DMX has to have a unique starting address. The addressing feature is  
what allows DMX to function properly. The DMX address of a fixture is what allows it to  
communicate with a controller properly. The DMX addressing also allows the fixture to  
ignore any DMX information coming from the controller that is not meant specifically for  
the fixture. Because each fixture is connected in a daisy-chain fashion it is imperative to  
assign a proper and unique starting DMX address to each and every fixture. The DMX  
address is non-destructive and will remain in the fixture’s memory even when the power  
to the unit is switched off. Memory is backed-up and retain by an internal power source  
that should last about five years. For proper DMX addressing see Section 10/Page 32 of  
this user manual.  
9.1.2. Display the DMX 512 value of each channel  
With this function you can display the DMX 512 value of each channel. The display will  
automatically readout the changing DMX values as they are received.  
9.1.3. Slave setting  
With this function, you can define the device as slave for operation in Master/Slave mode.  
9.1.4. Auto Program  
This function allows the internal programs to run. The desired program is selected in the  
“Select program” section of the control menu. You can set the number of steps under  
“Edit program”. You can edit the individual scenes under “Edit scenes”. With this  
function, you can run the individual scenes either automatically, i.e. with the adjusted  
Step-Time.  
9.1.5. Music control  
With this function, you can run the internal program via sound.  
©Elation Professional, Los Angeles CA.  
24  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
9.2 Information:  
9.2.1. Time information  
Current time  
This function displays the running time of the fixture from the last power on. The  
display shows “XXXX”, where “XXXX” represents the number of hours the fixture has  
been running. This counter is automatically reset after every power-on.  
Total Run Time  
This function tracks the total running time of the fixture from the very first start-up.  
Where “XXXX ”represents the total number of running hours. This time is none  
destructive and will remain in the fixtures memory indefinitely.  
Total Lamp Time  
This function tracks the total number of lamp running hours. Where “XXXX”  
represents the number of hours the lamp has been running. This counter should be  
reset after every lamp change.  
Lamp off time  
This function displays the running time of the lamp from the last power on. The  
display shows “XXXX”, where “XXXX” represents the number of minutes the lamp  
has been running since it was last struck. This counter is automatically reset after  
every power-on.  
Clear lamp time  
This function resets the lamp “ON” time to zero. Please reset the lamp “ON” time at  
every lamp replacement. This procedure tracks the lamp running time so the lamp  
can be replaced at the end of it’s recommended duty cycle.  
• Select “Clear lamp time” in the system menu.  
• The LCD will display “ON” or “OFF.” Were “ON” will reset the lamp time.  
• Press enter to confirm.  
• Press the Mode/Esc-button to return to the main menu.  
©Elation Professional, Los Angeles CA.  
25  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
9.2.2. Temp. Info.  
Base Temp – This function will display the base temperature of the fixture.  
Head Temp – This function will display the head temperature of the fixture.  
9.2.3. Software version  
This function will display the current operating software version of the fixture.  
Select “Software Version” in the system menu.  
Press enter to confirm.  
The LCD will read “V-X.X”, “X.X” represents the version number, e.g.  
“V-1.0”, “V-2.6”.  
Use the UP and DOWN buttons to toggle through the software version of  
different IC’s.  
Press the Mode/Esc-button to return to the main menu.  
9.3 Lamp Control:  
9.3.1. Lamp on/off  
With this function you can switch the lamp on or off via the Control Board.  
• Select "Lamp on/off" by turning the LCD controls.  
• Press the LCD controls, the display shows “ON” or “OFF”.  
• Turn the LCD controls to select “ON” if you wish to strike the lamp or “OFF” in order  
to switch it off.  
• Press “ENTER” to confirm.  
• Press the Mode/Esc-button in order to return to the main menu.  
9.3.2. Automatic Lamp On  
With this function you can select if the lamp will be switched on when switching the power  
on. Select “ON” by turning the LCD controls if you wish to enable this function or “OFF”  
if you don’t.  
9.3.3. Lamp on via external DMX controller  
With this function you can select if you can switch the lamp on via an external controller.  
Select “ON” by turning the LCD controls if you wish to enable this function or “OFF” if you  
©Elation Professional, Los Angeles CA.  
26  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
don’t.  
9.3.4. Lamp off via external DMX controller  
With this function you can select if you can switch the lamp off via an external controller.  
Select “ON” by turning the LCD controls if you wish to enable this function or “OFF” if  
you don’t.  
9.3.5. Lamp Off if no DMX  
With this function you can select to switch off the lamp off automatically if there is no DMX  
signal). Select “ON” by turning the LCD controls if you wish to enable this function or  
“OFF” if you don’t.  
9.3.6. Lamp on at temp.  
With this function you can set the inside temperature from which the projector will strike  
the lamp after an automatic lamp shut off.  
9.3.7. Lamp off at temp.  
With this function you can set the inside temperature at which the projector will  
automatically switch the lamp off. Turn the LCD controls to select the maximum inside  
temperature between 80°C and 139°C. Inside temperatures below 90°C are not critical.  
90°C and more should lead to the lamp being switched off. Please note that the outside  
temperature should not exceed 45°C.  
9.4 Personality:  
9.4.1. Status setting  
A. Address via DMX - This function allows the DMX address to remotely be adjusted  
from a DMX console. This setting requires special settings for both the controller and  
the fixture. RDMX is on by default. For operational instructions please see Section  
10/Page 32 of this manual “Remote DMX addressing.”  
B. Run if no DMX – This function dictates how the fixture will function if it looses  
DMX signal during normal operation. The default function is set to hold, in which  
©Elation Professional, Los Angeles CA.  
27  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
the fixture will lock into the last DMX signal it received and remain in that position  
until it is turned off or begins receiving a new DMX signal. If the fixture is turned  
on without any DMX signal, the fixture will automatically go in to sound-active  
mode. Available settings are: “Close” – Shutter flags will close. “Hold” – Fixture  
will remain at it’s last settings. “Auto Program” – Fixture will go into stand-alone  
mode, running the built-in program. “Music Control” – The fixture will go into  
sound-active mode.  
C. Pan Reverse - This function allows you to invert all pan movements. Use the Up  
and Down buttons to turn this function On and Off. Press the Enter button to accept  
the change or the Mode button to cancel and return to the main menu.  
D. Tilt Reverse - This function allows you to invert all tilt movements. Use the Up and  
Down buttons to turn this function On and Off. Press the Enter button to accept the  
change or the Mode button to cancel and return to the main menu.  
E. Fine resolution – This function changes the DMX channel operation from 8bit to  
16bit.  
F. Pan Degree – This function changes the maximum Pan resolution from either 540˚  
or 630˚. The default function is 540˚.  
G. Feedback This function turns the feedback correction on or off. This function is set  
to on as default.  
H. Movement Speed – This function changes the order of the DMX channels to more  
closely match similar fixtures from different vendors, thus allowing the user easier  
functionality when programming. There are four different mode variations.  
I. Mic Sensitivity – This function make the internal microphone more or less sensitive  
to sound. This function only works in conjunction with the sound active modes. The  
default setting is 70% and setting range from 0 % to 99 %.  
9.4.2. Service Settings – These adjustments and settings should only be performed by a  
technician familiar with the functionality this fixture. Incorrect setting of these  
©Elation Professional, Los Angeles CA.  
28  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
functions may result reduced performance or damage to the fixture.  
Service Password: The correct password must be entered before attempting wheel  
calibration, changing fan voltage, or changing the gobo speed.  
Fan Voltage: This function will change the fan voltage from either “Low” or “High.”  
Low will send normal voltage to the fan, for normal operation. High will send slightly  
higher voltage to fans that allows the fans to operate at higher than normal speeds.  
This setting should only be used in extreme cases of higher than normal  
temperatures. Using the fans in “HIGH” mode will decrease fan life over time. Low is  
the default setting.  
Gobo Speed: This function will change the speed at which the gobo wheel moves.  
This function allows Design Spot 575Bs and Design Spot 250s to be implemented  
together in the same rig. There are two different settings, “Quick” and “Slow.” Slow  
will move the gobo wheel at a speed that matches the first generation Design Spot  
250. The “Quick” setting will advance the wheel at a new, faster rate than the original  
Design Spot 250. “Quick” is the default setting.  
9.4.3. Fans Control - This function is used to change the functionality of the internal  
cooling fans. The available selections are: 1) “AUTO” – The fans will automatically  
switch between low and high speeds depending on the internal operating  
temperature. 2) “HIGH” – The fans will run in high-speed mode regardless of  
operating temperature. 3) “LOW” – The fans will remain in low speeds regardless of  
internal operating temperature.  
9.4.4. Temperature C/F – This function changes the temperature unit readout from either  
the temperature Celsius or Fahrenheit.  
9.4.5. Initial effect - With this function, you can adjust with which value the respective  
channels will start.  
9.4.6. Restore Default - With this function you can restore the factory settings of the  
device. All settings will be set back to the default values (shaded). Any edited  
©Elation Professional, Los Angeles CA.  
29  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
scenes will be lost.  
9.5 Reset Functions:  
9.5.1 Reset All: This function will reset all internal motors to the home position.  
9.5.2 Reset Pan and Tilt: This function will only reset the pan and tilt motors to the home  
position.  
9.5.3 Reset Colors: This function will only reset the color wheel and the CMY filter motors  
to the home position.  
9.5.4 Reset Gobos: This function will only reset the gobo wheels to the home position.  
9.5.5 Reset Shutter: This function will only reset the blackout shutter to the home  
position.  
9.5.6 Reset Others: This function will reset all other motors to the home position.  
9.6 EFFECT ADJUST:  
9.6.1 Test Channel – This menu function allows the user to select each individual fixture  
channel and test it’s function independently from the control board.  
9.6.2 Lamp adjustment (manual control) – This function readies the fixture for lamp  
optimization in a simple single step procedure. This function will center the pan and tilt  
motors while at the same time open the shutter and bring the dimmer to 100%. The  
pan and tilt function will still operate if the fixture needs to be positioned to a flat clear  
surface.  
9.6.3 Calibrate values – This function should only be used by a qualified technician. This  
function allows a user to make small adjustments to the effect wheels (color, gobo,  
shutter, etc) to compensate for ware or in the event a sensor has been knocked  
slightly out of place. Because improper use of this function can result in undesired  
operation this function has been password protected. The password is 050 and must  
©Elation Professional, Los Angeles CA.  
30  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
be entered each time the calibration menu function is entered.  
9.7 USER MODE:  
9.7.1 User mode – This function allows the user to create user defined channel orders  
allowing the fixture to match the channel order of other fixtures on the market for easier  
operation. A total of three user modes may be configured: User Mode A, User Mode B,  
and User Mode C.  
9.7.2 Edit User mode – This function allows the user to make the actual changes in the  
user-defined modes that are accessed through the previous function.  
9.8 EDIT PROGRAM:  
9.8.1 Select program – This function allows the user to select one of ten of the user defined  
built-in programs. This program is then accessed in “Function Mode” under “Program  
Run.”  
9.8.2 Edit program – This function allows the user to edit the built-in programs.  
9.8.3 Edit Scenes – This function allows the user to edit or define the actual scenes that are  
stored in the user defined built-in programs that are accessed in the previous step.  
9.8.4 Rec Controller - The Design Spot 575B features an integrated DMX recorder by  
pre-programmed scenes can be transmitted to the fixture via any standard DMX  
controller. This function allows those scenes to be stored in to the fixture’s built-in  
memory and then subsequently used to create user-defined programs.  
©Elation Professional, Los Angeles CA.  
31  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
10. DMX ADDRESSING  
Setting the DMX address - After the fixture is turned “ON” it will immediately complete a  
reset process that test all the fixture’s functions. When the reset process concludes the LCD  
will display the fixture’s current DMX address. If the fixture is not receiving a DMX signal, the  
display will flash continuously. To set or adjust a DMX address, please follow the procedure  
below:  
1. Toggle through the menu by pressing the Up and Down buttons until the display  
reads “Set DMX Address.” Tap the enter button to make changes to the address.  
2. While the current three-digit address is flashing use the “UP” and “DOWN”  
buttons to select a new address. Once the new address has been selected, lock  
the new address into the fixture’s memory by pressing the “ENTER” button.  
The DMX address is non-volatile and will remain in the fixture’s memory even when the  
power to the unit is switched off. Memory is backed-up and retain by an internal power  
source that should last about five years  
Remote DMX addressing (RDMX) / Address Via DMX- This function allows the DMX  
address to be changed remotely from a DMX console. This setting requires special settings  
for both the controller and the fixture. RDMX is on by default. Follow the procedure listed  
below to access the RDMX functions:  
Fixture Settings:  
1. Access the main menu and use the UP or DOWN to get to the “Personality”  
menu, then press ENTER.  
2. Once in the “Personalities” menu, tap the UP or Down to get to the “Status  
Settings “ menu, press ENTER.  
3. Once in the “Status Settings” tap the UP or Down to get to the “Address via  
DMX” function and press ENTER.  
4. “Address via DMX” is the function that turn the RDMX function on and off.  
5. Press the UP button to display “ON” to activate this function, or “OFF” to  
deactivate this function.  
6. Press ENTER to confirm.  
©Elation Professional, Los Angeles CA.  
32  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
7. Press MODE/ESC to return to the main menu.  
Controller Settings:  
1. Set the DMX value of channel 1 to a value of 7.  
2. Set the DMX value of channel 2 to a value of 7 or 8. When channel 2 is set  
to "7" you can adjust the starting address between 1 and 255. When set to  
"8" you can adjust the starting address between 256 and 511.  
3. Use channel 3 to set your desired DMX starting address. For example: If  
you want to set the starting address to 57, set channel 1 to a value of “7,”  
set channel 2 to a value of “7” and use channel 3 to set your address to 57  
by selecting a channel value of 57. Example 2: If you want to set the  
starting address to 420, set channel 1 to a value of “7,” channel 2 to "8"  
and channel 3 to "164" (256+164=420).  
4. Wait for approximately 20 seconds for the unit to complete the  
address reset function.  
©Elation Professional, Los Angeles CA.  
33  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
11.OPERATION  
Operating Modes: The Design Spot 575B™ can operate in several different modes. This  
next section will detail the differences in the operating modes.  
• Auto Program Mode (Master) - The fixture will chase through the built-in programs,  
sending a DMX control signal to all other fixtures connect via DMX cables instruction for a  
synchronized light show.  
• Auto Program Mode (Stand-alone) - The fixture will chase through the built-in program.  
This feature is great for store front with custom logos, where as the logos need to be  
displayed but the use of a controller is unwanted.  
• Music Control Mode (Stand-alone) - The fixture will react to sound, chasing through the  
built-in programs. Great for small clubs or DJs that do not want to bother with programming.  
• Music Control Mode (Master/Slave) - You can daisy chain up to 16 fixtures together to  
get a synchronized light show without the need of an external controller. The fixtures will react  
to sound, chasing to a synchronized light show.  
• Set To Slave – This function will set the fixture to slave mode for use in either the auto  
program or music control program modes.  
• DMX control mode - This function will allow you to control each individual fixtures traits  
with a standard DMX-512 controller such as the Elation® Show Designer 2 or Show Designer  
3.  
11.1  
Stand-Alone Operation (Auto Program or Music Control): This mode allows a  
single fixture to run to the built-in programs with or without sound. Only use this  
mode when running a single fixture, or when running several fixtures as individuals.  
Mount your fixture in a secure and stable manner.  
For functionality without sound control: Access the “Function” menu and  
select the “Auto Program” function, this will give you access to the “Auto  
Program” submenu. See page 22 for the menu breakdown. Once in the  
“Auto Program” submenu select “Alone”  
For functionality that chases to sound: Access the “Function” menu and  
select the “Music Control” function, this will give you access to the “Music  
Control” submenu. See page 21 for the menu breakdown. Once in the  
©Elation Professional, Los Angeles CA.  
34  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
“Music Control” submenu select “Alone”  
11.2  
Master-Slave Operation (Auto Program or Music Control): This function allows  
up to 16 fixtures to be linked together to provide a synchronized light show without  
the use of a controller. Only use this when linking several Design Spot 575B  
together for use without a controller. Any fixture can act as a “Master or a “Slave.”  
Using XLR DMX cables, daisy chain your fixtures together via the XLR  
connectors. Remember the Male XLR connector is the input and the Female  
XLR connector is the output. The first fixture in the chain (master) will use  
the female XLR connector only - The last fixture in the chain will use the  
male XLR connector only. For longer cable runs we suggest a terminator at  
the last fixture.  
For the unit functioning as the “Master” unit follow the same procedures  
listed in the previous Stand-Alone section.  
For the “Slave” units, access the “Set To Slave” settings in the “Function  
Mode” menu and assign each slave fixture a designation (Slave 1, Slave 2,  
Slave 3…etc).  
11.3 Universal DMX Control: This function allows you to use a universal DMX-512  
controller such as the Elation® Show Designer 2™ or Elation® Show Designer 3™ to  
control head movement, the color wheel, the shutter (strobe), and all other DMX traits. A  
DMX controller allows you to create unique programs tailored to your individual needs.  
The Design Spot 575B™ uses 15 DMX channels. See page 41 for detailed description  
of the DMX traits. To control your fixture in DMX mode, follow the set-up procedures on  
pages 17-19 as well as the set-up specifications that are included with your DMX  
controller. Use the controller’s faders to control the various DMX fixture traits. This will  
allow you to create your own programs.  
Follow the instruction on page 32 to set the DMX address.  
Be sure to use a terminator on the last fixture, especially for longer cable  
runs (more than a 100 feet).  
For help operating in DMX mode consult the manual that was included with  
your DMX controller.  
©Elation Professional, Los Angeles CA.  
35  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
12. WORKING WITH BUILT-IN PROGRAMS  
The fixture comes equipped with a built-in DMX recorder that allows custom programs to be  
installed and recalled directly from the fixture’s control board. Programs can be created and  
stored using the fixture’s control board or by using an external DMX controller. The following  
instructions will detail the procedures for using the on-board system menu as well as using a  
DMX compliant controller.  
Memory Statistics:  
Quick Access Programs (Program Part): 3  
Total Number of Programs: 10  
Maximum Number of Steps (Scenes) per a Program: 64  
Total Number of Scenes (Steps): 250  
Step 1 – Building Scenes.  
The control will store a maximum of 250 scenes. These scenes are then used to create the  
programs. A program can store one or a maximum of 64 scenes. Keep in mind that a scene  
can only be access when it is stored in a “Program.” If you wish to build a static scene (a  
scene consisting of no movement) for a logo or gobo projection, the scene must be stored  
inside a program. To build scenes follow the instructions below:  
Access the main menu and toggle to “Edit Programs” which is menu function 8.  
Then tap the “ENTER” button and toggle to “Edit Scenes,” menu function 8-3.  
When you get to the “Edit Scenes” function tap the “ENTER” button. The screen will  
then change to Edit Scene 001, this will be menu function 8-3-1. You can then press  
the “ENTER” button to begin to edit scene 1 or use the “UP” and “DOWN” buttons to  
toggle to access scenes 2-250.  
Once in the scene edit screen you have access to the functions listed below.  
Tapping the “ENTER” button will instantly allow you to change the values of the  
selected function in real time. The values can be adjusted from 0~250. Once you  
achieved your desired value tap the “ENTER” button once again to automatically  
lock the value into the scenes memory. You can repeat the procedure for all  
functions listed below:  
-
-
“Auto Program” – Allows access to all 15 of the channel’s DMX traits.  
“PAN” – pan movement.  
©Elation Professional, Los Angeles CA.  
36  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
“PAN-Fine” – precision pan movement.  
“TILT” – tilt movement.  
“TILT-Fine” – precision tilt movement  
“Move Speed” – adjust pan and tilt motor speed  
“Gobo Wheel 1” – select gobos from gobo wheel 1  
“Gobo Rot. 1” – adjust gobo 1 indexing or rotation  
“Gobo Wheel 2” – select a gobo from gobo wheel 2  
“Prism” – select a prism, prism macro, or frost  
“Prism Rot.” – adjust the prism indexing or rotation  
“Color Speed” – adjust the CMY mixing speed  
“Color Macro” – select a built-in color mixing macro  
“Color Wheel” – select a color from the color wheel  
“Iris” – adjust the iris value  
“Focus” – adjust the focus value  
“Strobe” – adjust the strobe  
“Dimmer” – adjust the dimmer intensity  
“Scene Time” – set the hold time for the scene  
“Input By Out” – this function will store a scene from an external DMX  
console. See the next section for scene editing via an external DMX  
controller.  
Step 1B – Building Scenes from an External DMX Controller.  
The fixture includes a simple built-in DMX recorder. This recorded allow you to build a scene  
using your own DMX console and then send that scene to the fixture to be stored inside one  
of the fixture scene storage banks. Many people may find this procedure easier and quicker  
than using the on board menu functions as in “Step 1.” To store a scene from an external  
DMX controller follow the procedures below:  
-
-
Using your DMX controller build and store scenes as you normally would.  
Once you have built all your required scenes, enter the fixtures main menu  
and toggle to “Edit Programs” – “Edit Scenes”  
-
Using the UP and DOWN buttons to select a scene bank to store your scene.  
You may choose a bank from 1 ~ 250.  
©Elation Professional, Los Angeles CA.  
37  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
-
-
Once you reach your desired bank press the ENTER button and use the UP  
and DOWN button to reach “Input by Outside”  
Next, select a scene on your DMX console and press the ENTER button on  
the fixture. The scene should then be stored to the fixtures internal memory  
EPROM.  
-
Follow the next section to build a program with your scenes.  
Step 2 – Editing Programs.  
The control will store a maximum of 10 programs. A program can store one or a maximum of  
64 scenes. Keep in mind that a scene can only be access when it is stored inside one of the  
10 available programs. Follow the procedure below to build an internal program:  
Access the main menu and toggle to “Edit Programs” which is menu function 8.  
Then tap the “ENTER” button and toggle to “Program 1” menu function 8-2-1.  
When you get to the “Program 1” function tap the “ENTER” button. The screen will  
then change to Edit Steps 01, this will be menu function 8-2-1-1. Use the “UP” and  
“DOWN” buttons to toggle through the scenes created in “Step 1.” Press the  
“ENTER” button to add a scene to the program. Tapping the “Enter” button will  
automatically lock the selected scene into the programs’ memory. Repeat the  
process until all the desired scenes have been added to the program. Each program  
can store a maximum of 64 scenes.  
To test the program access “Program Test” in the “Program Edit” menu function.  
Step 3 – Playing a Program  
To initiate a program follow the procedure below:  
Access the main menu and use the “Up” and “Down” to toggle to “Function Mode”  
and tap the “Enter” button.  
In the next screen select “Auto Program” and tap the “Enter” button.  
There are now two selections, “Master” and “Alone.” Select “Master” when running  
multiple fixtures in a master/slave configuration. See section 11.2 “Master/ Slave  
Operation” on page 36 for proper set-up instructions. Select “Alone” when running a  
single fixture or when multiple fixtures in stand-alone mode. See section 11.1  
“Stand-Alone Operation” on page 34 for proper set-up instructions.  
©Elation Professional, Los Angeles CA.  
38  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
13. DMX CHANNEL TRAITS:  
The chart below details the channel layout for 15 DMX channels (default).  
In 8bit mode the “Pan Fine” and “Tilt Fine” channels are not used, thus converting the fixture  
into a 13-channel DMX fixture.  
CHANNEL 1: Pan Movement (max. 630°or 540˚ User Selectable)  
CHANNEL 2: 16bit Pan Movement (pan fine)  
CHANNEL 3: Tilt Movement (max. 265°)  
CHANNEL 4: 16bit Tilt Movement (tilt fine)  
CHANNEL 5: Color Wheel  
CHANNEL 6: Gobo Wheel 1 (Rotating)  
CHANNEL 7: Gobo Index, Gobo Rotation Speed/Direction (Gobo Wheel 1)  
CHANNEL 8: Gobo Wheel 2 (Fixed)  
CHANNEL 9: 3-Facet Prism Control  
CHANNEL 10: Focus Control Motor (Near ~ Far)  
CHANNEL 11: Strobe (0-13Hz), and Shutter close/open function + random strobe  
CHANNEL 12: Dimmer (Intensity) Control  
CHANNEL 13: Iris (Closed to Open)  
CHANNEL 14: Speed Control (Pan/Tilt movement, blackout selection)  
CHANNEL 15: Special (Auto program control + lamp on, motor reset, lamp switch off)  
DMX channel function and values:  
DMX channel functions and values (24 DMX channels):  
Function  
Mode/Channel  
Value  
St  
Ba Ex  
PAN Movement 8bit :  
Pan Movement  
1
1
1
2
3
4
0-255  
0-255  
0-255  
0-255  
Pan Fine 16bit  
2
3
4
Fine control of Pan movement  
TILT Movement 8bit :  
Tilt Movement  
2
Tilt Fine 16bit  
Fine control of Tilt movement  
©Elation Professional, Los Angeles CA.  
39  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
Color Wheel:  
0-13  
14-27  
Open / white  
Color 1  
28-41  
Color 2  
42-55  
Color 3  
56-69  
Color 4  
5
3
5
70-83  
Color 5  
84-97  
Color 6  
98-111  
112-127  
128-189  
190-193  
194-255  
Color 7  
Color 8  
Forwards rainbow effect from fast to slow  
No rotation  
Backwards rainbow effect from slow to fast  
Color Wheel Fine:  
Split Colors  
6
0-255  
Rotating gobos, cont. rotation:  
Open  
0-9  
10-19  
Rot. gobo 1  
20-29  
Rot. gobo 2  
30-39  
Rot. gobo 3  
40-49  
Rot. gobo 4  
50-59  
Rot. gobo 5  
6
4
7
60-69  
Rot. gobo 6  
70-89  
Gobo 1 shake slow to fast  
Gobo 2 shake slow to fast  
Gobo 3 shake slow to fast  
Gobo 4 shake slow to fast  
Gobo 5 shake slow to fast  
Gobo 6 shake slow to fast  
Rot. gobo wheel cont. rotation slow to fast  
90-109  
110-129  
130-149  
150-169  
170-189  
190-255  
Rotating gobo index, rotating gobo rotation:  
0-127  
Gobo indexing  
7
8
5
6
8
128-189  
190-193  
194-255  
Forwards gobo rotation from fast to slow  
No rotation  
Backwards gobo rotation from slow to fast  
Rotating gobo indexing Fine  
Fine indexing  
Fixed Gobos:  
Open/hole  
9
0-255  
10  
0-13  
14-27  
28-41  
42-55  
Gobo 1  
Gobo 2  
Gobo 3  
©Elation Professional, Los Angeles CA.  
40  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
56-69  
70-83  
Gobo 4  
Gobo 5  
84-97  
Gobo 6  
98-111  
112-127  
128-143  
144-159  
160-175  
176-191  
192-207  
208-223  
224-255  
Gobo 7  
Gobo 1 shake slow to fast  
Gobo 2 shake slow to fast  
Gobo 3 shake slow to fast  
Gobo 4 shake slow to fast  
Gobo 5 shake slow to fast  
Gobo 6 shake slow to fast  
Gobo 7 shake slow to fast  
Gobo wheel rotation from slow to fast  
Fixed gobo indexing Fine  
Fixed gobo Fine indexing  
11  
12  
13  
0-255  
3 facet rotating prism, Prism / Gobo macros:  
0-3  
Open  
4-63  
Forwards rotation from fast to slow  
64-67  
No rotation  
68-127  
Backwards rotation from slow to fast  
128-135  
136-143  
144-151  
152-159  
160-167  
168-175  
176-183  
184-191  
192-199  
200-207  
208-215  
216-223  
224-231  
232-239  
240-247  
248-255  
Macro 1  
Macro 2  
Macro 3  
Macro 4  
Macro 5  
9
7
Macro 6  
Macro 7  
Macro 8  
Macro 9  
Macro 10  
Macro 11  
Macro 12  
Macro 13  
Macro 14  
Macro 15  
Macro 16  
Focus:  
10  
11  
8
9
0-255  
0-255  
Continuous adjustment from near to far  
Focus Fine:  
Continuous adjustment Fine  
Shutter, strobe:  
Shutter closed  
No function (shutter open)  
14  
15  
0-31  
32-63  
©Elation Professional, Los Angeles CA.  
41  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
64-95  
Strobe effect slow to fast  
No function (shutter open)  
Pulse-effect in sequences  
No function (shutter open)  
Random strobe effect slow to fast  
No function (shutter open)  
Dimmer intensity:  
96-127  
128-159  
160-191  
192-223  
224-255  
12  
10  
16  
17  
0-255  
0-255  
Intensity 0 to 100%  
Fine Dimmer intensity:  
Dimmer intensity fine  
Iris:  
0-191  
Max. diameter to Min.diameter  
Pulse opening fast to slow  
Pulse closing slow to fast  
Speed Pan/Tilt movement:  
max to min speed  
13  
14  
11  
12  
18  
19  
192-223  
224-255  
0-225  
226-235  
236-245  
246-255  
Blackout by movement  
Blackout by all wheel changing  
No function  
Lamp on/off, reset, internal programs:  
Color & gobo change normal  
Color change to any position  
Color & gobo change to any position  
Lamp on  
0-19  
20-29  
30-39  
40-59  
60-79  
Lamp switch off  
80-84  
All motor reset  
85-87  
Scan motor reset  
88-90  
Colors motor reset  
91-93  
Gobo motor reset  
15  
13  
20  
94-96  
Shutter & Dimmer motor reset  
Other motor reset  
97-99  
100-119  
120-139  
140-159  
160-179  
180-199  
200-219  
220-239  
240-255  
Internal program 1 (secne1~8 of EEPROM)  
Internal program 2 (secne9~16 of EEPROM)  
Internal program 3 (secne17~24 of EEPROM)  
Internal program 4 (secne25~32 of EEPROM)  
Internal program 5 (secne33~40 of EEPROM)  
Internal program 6 (secne41~48 of EEPROM)  
Internal program 7 (secne49~56 of EEPROM)  
Music Control (scene of Program 1)  
©Elation Professional, Los Angeles CA.  
42  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
14. FUSE REPLACEMENT  
Caution: Always replace with the exact same type fuse, unless otherwise specified by an  
authorized Elation® service technician. Replacing with anything other than the specified part  
can damage your unit and will void your manufactures warranty.  
Warning: If you continue to blow fuses, STOP using the fixture. Contact customer support for  
further instructions, you may have to return the unit for servicing. Continuing to use the unit  
may cause serious damage.  
Fuse Replacement: Locate and remove the unit’s power cord from the main power supply.  
Once the cord has been removed located the fuse holders located on the side panel near the  
power input connection. Using a flat-head screwdriver unlock the fuse holder from its’  
housing by turning the holder in a counter-clockwise direction. Once the fuse holder has been  
unlocked, pull back on the fuse holder to expose the fuse. Gently pull out the bad fuse and  
discard of it properly and replace it with an exact match. Reassemble in reverse order.  
©Elation Professional, Los Angeles CA.  
43  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
15.ERROR CODES:  
When power is applied, the unit will automatically enter a “reset/test” mode. This mode brings  
all the internal motors to a home position. If there is an internal problem with one or more of  
the motors an error code will flash in the display in the form of “XXer” were as XX will  
represent a function number. For example, when the display shows “02Er,” it means there is  
some type of error with the channel 2 motor. If there are multiple errors during the start-up  
process they will all flash in the display. For example: if the fixtures has errors on channel 1,  
channel 2, and channel 5 all at the same time, you will see the error message “01Er”, “02Er,”  
and ”05Er” flash repeated 5 times.  
If an error does occur during the initial start-up procedure the fixture will self-generate a  
second reset signal and try to realign all the motors and correct the errors, if the error persist  
after a second attempt a third attempt will be made.  
If after a third attempt all the errors have not been corrected the fixture will make the following  
determinations: 1) 3 or more errors - The fixture cannot function properly with three or more  
errors therefore the fixture will place itself in a stand-by mode until subsequent repairs can be  
made. 2) Less than 3 errors - The fixture has less than 3 errors, therefore most other  
functions will work properly. The fixture will attempt to operate normally until the errors can be  
correct by a technician. The errors in question will remain flashing in the display as a reminder  
of internal errors.  
Pan Er  
(PAN-yoke movement error) This message will appear after the reset of the fixture if the  
yoke’s magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the  
stepping-motor is defective (or its driving IC on the main PCB). The PAN- movement is not  
located in the default position after the reset.  
Tilt Er  
(TILT-head movement error) This message will appear after the reset of the fixture if the  
head’s magnetic-indexing circuit malfunctions (sensor failed or magnet missing) or the  
stepping-motor is defective (or its driving IC on the main PCB). The TILT- movement is not  
©Elation Professional, Los Angeles CA.  
44  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
located in the default position after the reset.  
Color Er  
(Color wheel- error) This message will appear after the reset of the fixture if the yoke’s  
magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the  
stepping-motor is defective (or its driving IC on the main PCB). The color wheel is not located  
in the default position after the reset.  
Rotation gobo Er  
(Rotating gobo wheel 1- error) This message will appear after the reset of the fixture if the  
yoke’s magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the  
stepping-motor is defective (or its driving IC on the main PCB). The Rotating gobo wheel 1 is  
not located in the default position after the reset.  
Gobo Rotation Er  
(Gobo Rotation wheel 1- error) This message will appear after the reset of the fixture if the  
yoke’s magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the  
stepping-motor is defective (or its driving IC on the main PCB). The Gobo Rotation wheel 1 is  
not located in the default position after the reset.  
Prism Rotation Er  
(Prism Rotation-wheel error) This message will appear after the reset of the fixture if the  
yoke’s magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the  
stepping-motor is defective (or its driving IC on the main PCB). The Prism Rotation -wheel is  
not located in the default position after the reset.  
Shutter, Strobe Er  
(Shutter, Strobe-wheel error) This message will appear after the reset of the fixture if the  
yoke’s magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the  
stepping-motor is defective (or its driving IC on the main PCB). The Shutter, Strobe -wheel is  
not located in the default position after the reset.  
©Elation Professional, Los Angeles CA.  
45  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
Focus Er  
(Focus error) This message will appear after the reset of the fixture if the yoke’s  
magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the  
stepping-motor is defective (or its driving IC on the main PCB). The Focus is not located in the  
default position after the reset.  
Iris Er  
(Iris error) This message will appear after the reset of the fixture if the yoke’s  
magnetic-indexing circuit malfunction (sensor failed or magnet missing) or the  
stepping-motor is defective (or its driving IC on the main PCB). The Iris is not located in the  
default position after the reset.  
©Elation Professional, Los Angeles CA.  
46  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
16. CLEANING AND MAINTENANCE  
The following points have to be considered during the inspection:  
1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may  
fall out during normal operation resulting in damage or injury as larger parts could fall.  
2. There must not be any deformations on the housing, color lenses, rigging hardware  
and rigging points (ceiling, suspension, trussing). Deformations in the housing could  
allow for UV radiation leakage. Damaged rigging points or unsecured rigging could  
cause the unit to fall and serious injure a person.  
3. All mechanical parts and motors should not show any traces of serious wear and  
should rotate freely.  
4. Electric power supply cables must not show any damage, material fatigue or  
sediments. Never remove the ground prong from the power cable.  
Further instructions depending on installation and usage have to be adhered by a skilled  
installer and any safety problems should be addressed before attempting operation.  
We recommend frequent cleaning of the fixture to ensure operational longevity and crisp light  
output. When cleaning, please use a moist, lint-free cloth. Never use alcohol or solvents.  
There are no user serviceable parts inside this fixture with the exception of the lamp. Please  
refer all other service related issues to an authorized Elation service technician.  
Should you decide to service the fixture yourself please order genuine Elation parts directly  
from Elation.  
©Elation Professional, Los Angeles CA.  
47  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
17. 2-YEAR LIMITED WARRANTY  
A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional®  
products to be free of manufacturing defects in material and workmanship for a period of two  
years, (730 days) from the date of purchase. This warranty shall be valid only if the product is  
purchased within the United States of America, including possessions and territories. It is the  
owner’s responsibility to establish the date and place of purchase by acceptable evidence, at  
the time service is sought.  
B. For warranty service, send the product only to the Elation Professional® factory. All  
shipping charges must be pre-paid. If the requested repairs or service (including parts  
replacement) are within the terms of this warranty, Elation Professional® will pay return  
shipping charges only to a designated point within the United States. If the entire instrument is  
sent, it must be shipped in its original package. No accessories should be shipped with the  
product. If any accessories are shipped with the product, Elation Professional® shall have no  
liability what so ever for loss of or damage to any such accessories, nor for the safe return  
thereof.  
C. This warranty is void if the serial number has been altered or removed; if the product is  
modified in any manner which Elation Professional® concludes, after inspection, affects the  
reliability of the product; if the product has been repaired or serviced by anyone other than the  
Elation Professional® factory unless prior written authorization was issued to purchaser by  
Elation Professional®; if the product is damaged because not properly maintained as set forth  
in the instruction manual.  
D. This is not a service contract, and this warranty does not include maintenance, cleaning  
or periodic check-up. During the period specified above, Elation Professional® will replace  
defective parts at its expense, and will absorb all expenses for warranty service and repair  
labor by reason of defects in material or workmanship. The sole responsibility of Elation  
Professional® under this warranty shall be limited to the repair of the product, or replacement  
thereof, including parts, at the sole discretion of Elation Professional®. All products covered by  
this warranty were manufactured after January 1, 1990, and bare identifying marks to that  
©Elation Professional, Los Angeles CA.  
48  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
effect.  
E. Elation Professional® reserves the right to make changes in design and/or improvements  
upon its products without any obligation to include these changes in any products theretofore  
manufactured.  
F. No warranty, whether expressed or implied, is given or made with respect to any  
accessory supplied with products described above. Except to the extent prohibited by  
applicable law, all implied warranties made by Elation Professional® in connection with this  
product, including warranties of merchantability or fitness, are limited in duration to the  
warranty period set forth above. And no warranties, whether expressed or implied, including  
warranties of merchantability or fitness, shall apply to this product after said period has  
expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as  
is expressly provided above; and under no circumstances shall Elation Professional® be  
liable for any loss or damage, direct or consequential, arising out of the use of, or inability to  
use, this product.  
G. This warranty is the only written warranty applicable to Elation Professional® Products  
and supersedes all prior warranties and written descriptions of warranty terms and conditions  
heretofore published.  
©Elation Professional, Los Angeles CA.  
49  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
18. Photometric Data:  
©Elation Professional, Los Angeles CA.  
50  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
19. GOBOS:  
©Elation Professional, Los Angeles CA.  
51  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
20. DIMENSIONAL DRAWINGS:  
©Elation Professional, Los Angeles CA.  
52  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
21. CIRCUIT SCHEMATIC  
©Elation Professional, Los Angeles CA.  
53  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
22. TECHNICAL SPECIFICATIONS  
Power supply  
Power consumption  
Fuse protection  
90 ~ 260V, 50 ~ 60 Hz  
800 Watt, 4.5 A, Magnetic ballast, (blind current compensated)  
120V = 10A/250V, GMA (5x20mm fine-wire fuse)  
220V = 5A/250V, GMA (5x20mm fine-wire fuse)  
Lamp  
Type  
Philips MSR575/2  
1000 Hrs  
Life time  
Color temperature  
Luminous flux  
Optical system  
7200˚ K  
49.000 lm  
Parabolic dichroic glass reflector  
Lenses hardened and tempered, anti-reflex coated  
Colors  
8 dichroic filter plus white, half-color compatible  
Gobos  
Gobo-wheel 1: 6 interchangeable rotating gobos plus "open", 4 glass Gobos  
Gobo-wheel 2: 6 interchangeable fixed gobos plus "open"  
Gobo outside diameter 26.9 mm, image size 23 mm  
Gobo thickness (max): glass = 1 mm, steel = 0.15 mm  
Prism  
Rotating 3-face prism, rotating and variable in speed  
Shutter / Strobe / Dimmer  
Strobe effect with variable speed 1 - 10 flashes per second  
Continuously mechanical dimmer 0 - 100%  
Iris  
Motor driven iris from open to close, variable speed, pulse effect  
Focus  
Motor driven focus from near to far away  
Effect wheel  
Rotating and indexed Effect wheel, different patterns, exchangeable  
DMX Channels  
24 (16bit – default) or 22 (8bit – user selectable) or 20  
Drive  
Standard DMX-512, 3 pole XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1 or 5 pole XLR; n/a = Pin  
5, n/a = Pin 4, [+] = Pin 3, [-] = Pin 2, [Ground] = Pin 1  
Starting DMX [001].  
Pan / Tilt  
Pan - movement  
630°in max. 2.0 seconds, 16 bit resolution  
265°in max. 1.5 seconds, 16 bit resolution  
Tilt - movement  
Weights and Measures  
©Elation Professional, Los Angeles CA.  
54  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Spot 575B™  
Width of the base  
Length of the base  
Width of Head  
18” / 46cm (Including Handles)  
13.75” / 35cm (Without Handles)  
18.5” / 47cm  
Height (head vertical)  
Weight (net)  
25” / 63.5cm  
37.6Kgs / 83Lbs  
Operating Noise Levels (Base level 46.8dB)  
Mode: Auto  
Mode: High  
Mode: Auto  
1m = 55.9 dB  
1m = 56.2 dB  
1m = 51.6 db (Lamp off)  
Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.  
©Elation Professional, Los Angeles CA.  
55  
Design Spot 575B™  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Elation Professional  
6122 S. Eastern Ave.  
Los Angeles, CA. 90040  
323-582-3322 / 323-832-9142 fax  
Rev. 11/24/2009  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Vacuum Cleaner ES 2100 User Manual
Extron electronic Network Card BNCM RCAM 6 User Manual
Fisher Price Car Seat 79701 User Manual
Garmin Marine GPS System 190 00683 01 User Manual
GE Microwave Oven JEM31F User Manual
GE Monogram Refrigerator ZIF36N LH User Manual
GE Water Heater GN75ENSRSA User Manual
GE Water System 215C1044P010 3 User Manual
Global Machinery Company Saw LS750P JM User Manual
Goldmund Stereo Amplifier MIMESIS 330 User Manual