MULTIMEDIA PROJECTOR
MODEL LC-W4
✽ Projection lens is optional.
OWNER'S INSTRUCTION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
Follow all warnings and instructions marked on the projector.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPLIANCES
Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
CAUTION!
This is a Class A equipment. This equipment can cause interference in residential areas; in this case, the operator
can be asked to take adequate countermeasures.
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure
that the plug will fit into the power outlet. Do not try to defeat this safety feature.
Should you be unable to insert the plug into the outlet, contact your electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
FEATURES AND DESIGN
6
7
COMPUTER INPUT
25
SELECTING INPUT SOURCE
25
25
27
SELECTING COMPUTER SYSTEM
PREPARATION
COMPATIBLE COMPUTER SPECIFICATIONS
PC ADJUSTMENT
28
28
29
AUTO PC ADJUSTMENT
MANUAL PC ADJUSTMENT
NAME OF EACH PART OF PROJECTOR
7
8
8
9
9
9
10
10
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
LENS INSTALLATION
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT
31
31
32
IMAGE LEVEL ADJUSTMENT
POSITIONING PROJECTOR
LENS SHIFT ADJUSTMENT
PICTURE LEVEL AND TILT ADJUSTMENT
MOVING PROJECTOR
PICTURE SCREEN ADJUSTMENT
33
VIDEO INPUT
34
CONNECTING PROJECTOR
11
SELECTING INPUT SOURCE
SELECTING VIDEO SYSTEM
34
35
36
36
37
TERMINALS OF PROJECTOR
CONNECTING TO COMPUTER
CONNECTING TO VIDEO EQUIPMENT
11
14
15
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT
IMAGE LEVEL ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
38
BEFORE OPERATION
16
SETTING
39
TOP CONTROLS AND INDICATORS
16
OPERATION OF REMOTE CONTROL
17
17
18
SETTING MENU
39
LASER POINTER FUNCTION
REMOTE CONTROL BATTERIES INSTALLATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
MENU BAR
19
19
19
20
APPENDIX
43
OPERATING WIRELESS MOUSE
43
MAINTENANCE
43
43
44
44
45
46
WARNING TEMP. INDICATOR
AIR FILTER CARE AND CLEANING
CLEANING PROJECTION LENS
LAMP MANAGEMENT
BASIC OPERATION
21
TURNING ON / OFF PROJECTOR
21
LAMP REPLACEMENT
ADJUSTING SCREEN
22
22
22
22
22
23
23
23
ZOOM ADJUSTMENT
TROUBLESHOOTING
INDICATORS AND PROJECTOR CONDITION
MENU TREE
48
50
51
FOCUS ADJUSTMENT
LENS SHIFT ADJUSTMENT
KEYSTONE ADJUSTMENT
PICTURE FREEZE FUNCTION
NO SHOW FUNCTION
TECHNICAL SPECIFICATIONS
53
P-TIMER FUNCTION
SOUND ADJUSTMENT
24
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its
respective corporation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AND DESIGN
This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)
technology.
◆ Motor-driven Lens Shift
◆ Compatibility
Projection lens can be moved up and down with motor-
driven lens shift function. This function makes it easy to
provide projected image where you want.
Zoom and focus can be also adjusted with motor-driven
operation.
This projector widely accepts various video and
computer input signals including;
● Computers
IBM-compatible or Macintosh computer up to 1600
x 1200 resolution.
● 6 Color Systems
◆ Power Management
Power Management function is provided to reduce power
consumption while a projector is not in use.
This Power Management function operates to turn
Projection Lamp off when a projector detects signal
interruption and any button is not pressed. Projection
Lamp is automatically turned on again when a projector
detects signal or any operation button is pressed.
This projector is shipped with this function ON.
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL-
N color system can be connected.
● Component Video
Component video signal, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i, 1080i-50 or 1080i-
60, can be connected.
● S-Video
S-Video signal, such as a S-VHS VCR output
signal, can be connected.
◆ Digital Visual Interface
This projector is equipped with DVI 29-pin terminal for
connecting DVI output from a computer.
◆ High Resolution Image
This projector provides 1366 x 768 dots resolution for
computer input and 800 horizontal TV lines. Resolution
from a computer between XGA (1024 x 768) and UXGA
(1600 x 1200) is compressed into 1024 x 768 dots. This
projector can not display image of over 1600 x 1200
dots. When resolution of your computer is more than
1600 x 1200, reset a computer output for lower
resolution.
◆ Multi Versatile Platform
This projector applies various input/output terminals and
3 terminal slots for expansion to tune to diversity of
signals from computers and video equipment.
◆ Selectable Terminal Slots
3-built-in Terminal Slots enable you to arrange any
combinations of input sources just by changing Terminal
Boards. For Terminal Boards, contact sales dealer
where you purchased a projector.
◆ Multi-Scan System
This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for troublesome manual adjustment of frequency
and other settings.
◆ Laser Pointer Function
Remote Control Unit supplied with this projector includes
Laser Pointer function. This function helps you to make
a smart presentation on a projected screen.
◆ One-Touch Auto PC Adjustment
Incoming computer video signals are recognized and
best adjustment is automatically set by Auto PC
Adjustment. No complicated setup is necessary and
projection is always precise.
◆ Wireless Mouse
Remote Control Unit supplied with this projector has
Wireless Mouse function for a connected computer. This
function enables you to operate both projector and
computer with Remote Control Unit only.
◆ Progressive Scan Function
This function converts interlace video signals into
progressive scan signals and provide fine picture quality.
◆ Multilanguage Menu Display
Operation menu is displayed in; English, German,
French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean or Japanese.
◆ Digital Zoom (for Computer)
Digital Zoom function adjusts image size to approx. 1/4 ~
49 times of original image size, allowing you to focus on
crucial information at a presentation.
◆ Network board (Optional)
Network board is an optional product to control and set
up a projector via the network cable by accessing to the
connected projector using the web browser on your
computer. It can be controlled and set up the projector
remotely. Contact the sales dealer where you purchased
this projector for optional parts.
◆ Keystone Correction
Positioning slant of a projector may result in distorted
image being displayed in a trapezoid shape. Keystone
Correction solves this problem by digitally altering
projection to produce undistorted images.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
NAME OF EACH PART OF PROJECTOR
FRONT
SPEAKERS
INFRARED
REMOTE RECEIVER
PROJECTION LENS
LENS CAP
(Option)
CARRYING HANDLE
EXHAUST VENT
ADJUSTABLE FEET
INFRARED
CAUTION
Do not turn on a projector with lens cap
attached. High temperature from light beam may
damage lens cap and result in fire hazard.
BACK
AIR INTAKE
REMOTE RECEIVER
EXHAUST VENT
VENT
HOT AIR EXHAUSTED !
Air blown from exhaust vent is hot. When
using or installing a projector, following
precautions should be taken.
● Do not put a flammable object near this vent.
● Keep rear grills at least 3.3’ (1m) away from
any object, especially heat-sensitive object.
● Do not touch this area, especially screws
and metallic parts. This area will become
hot while a projector is used.
LAMP
EXHAUST VENT
COVER
This projector detects internal temperature
and automatically controls operating power
of Cooling Fans.
POWER CORD
CONNECTOR
MAIN ON / OFF
SWITCH
BOTTOM
AIR INTAKE VENTS
This projector is equipped with cooling
fans for protection from overheating.
Pay attention to following to ensure
proper ventilation and avoid a possible
risk of fire and malfunction.
● Do not cover vent slots.
● Keep bottom clear of any objects.
Obstructions may block cooling air.
AIR INTAKE VENT
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
This projector uses nominal input voltages of 100-120 V
or 200-240 V AC. This projector automatically selects
correct input voltage. It is designed to work with single-
phase power systems having a grounded neutral
conductor. To reduce risk of electrical shock, do not plug
into any other type of power system.
Consult your authorized dealer or service station if you
are not sure of type of power supply being in use.
Connect a projector with a peripheral equipment before
turning a projector on. (Refer to pages 12 ~ 15 for
connection.)
Connect AC Power Cord (supplied) to
a projector.
AC outlet must be near this equipment
and must be easily accessible.
CAUTION
AC Power Cord must meet requirement of country where you use a projector.
Confirm AC plug type with chart below and proper AC power cord must be used.
If supplied AC Power Cord does not match AC outlet, contact your sales dealer.
Projector side
AC Outlet side
For U.S.A. and Canada
For Continental Europe
Ground
To POWER CORD
CONNECTOR on a
projector.
To AC Outlet.
(120 V AC)
To AC Outlet.
(200 - 240 V AC)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
LENS INSTALLATION
Before setting up a projector, install Projection Lens on Projector.
1. Before installation, check where a projector is used and prepare suitable lens. For specifications of a
Projection Lens, refer to manual separately attached or contact sales dealer where you purchased a
projector.
2. For installation, refer to installation manual supplied to a Projector.
When moving or setting up a projector, be sure to replace Lens Cap to protect surface. And be
careful not to hold or subject lens to strong forces. It may damage lens, cabinet, or mechanical parts.
POSITIONING PROJECTOR
This projector is designed to project on a flat projection
surface.
SCREEN
ROOM LIGHT
Brightness in a room has a great influence on picture
quality. It is recommended to limit ambient lighting in
order to provide best image.
VENTILATION
This projector is equipped with cooling fan to protect it from
overheating. Pay attention to following to ensure proper venti-
lation and avoid a possible risk of fire and malfunction.
● Do not cover vents with papers or other materials.
● Keep rear grill at least 3 feet (1 m) away from any
object.
● Make sure that there are no objects under a pro-
jector. An object under a projector may prevent a
projector from taking cooling air through bottom
EXHAUST VENT
(FRONT AND REAR SIDE)
AIR INTAKE VENT
(BOTTOM SIDE)
vent.
LENS SHIFT ADJUSTMENT
Projection lens can be moved up and down with motor-driven lens shift function. This function makes it easy to
provide projected image where you want.
Use LENS SHIFT button and
POINT UP/DOWN button to
move image up or down.
(Refer to page 22.)
MOVED UP OR DOWN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
PICTURE LEVEL AND TILT ADJUSTMENT
Picture tilt and projection angle can be adjusted by rotating
ADJUSTABLE FEET. Projection angle can be adjusted up
to 6.9 degrees by rotating Adjustable Feet.
DOWN
UP
UP
DOWN
ADJUSTABLE FEET
MOVING PROJECTOR
Use carry handle when moving a projector.
Replace lens cap and retract adjustable feet.
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR
● Do not drop or bump a projector, otherwise damages or malfunctions may result.
● When carrying a projector, use a suitable carrying case.
● Do not transport a projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to a projector. To transport a projector through a courier or transport service, consult
your dealer and best case should be applied.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector applies various input/output terminals and 3 terminal slots for expansion to tune to diversity of signals from
computers and video equipment. 3-built-in Terminal Slots enable you to arrange desired combinations of input sources just
by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector.
3 TERMINAL SLOTS (Factory set)
AUDIO
CONTROL PORT
DVI
R
L
DVI Terminal
(MONO)
AUDIO
CONTROL PORT
R/Pr
G/Y
B/Pb
H/HV
V
R
L
5 BNC Terminal
AV Terminal
(MONO)
AUDIO
S-VIDEO
C
VIDEO/Y
R
L
(MONO)
AUDIO OUT
USB
SERIAL PORT OUT
SERIAL PORT IN
R
L
R/C JACK
RESET
(MONO)
INPUT/OUTPUT
TERMINALS
REPLACEMENT OF TERMINAL
NOTE; When replacement of terminal board, MAIN
ON/OFF switch should be OFF position.
Remove 2 Screws on terminal.
1
Pull out terminal by holding handle.
2
Replace terminal. Insert terminal along Guide to fit Plug
into Socket.
Screws
3
Tighten screws to secure terminal.
4
Guide
Socket
NOTES ON ORDERING OR USING
OPTIONAL INTERFACE BOARD
When ordering or using Optional Interface Board
(Terminal Board), contact your sales dealer. When con-
tacting the sales dealer, tell the Optional Control
Number (Op.cont.No.) in the menu that is located under
Language Select Menu. (See page 39.)
Plug
Figure shows HDB 15-PIN terminal (Optional parts).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
INPUT/OUTPUT TERMINALS AND JACKS
INPUT 2
INPUT 1
INPUT 1, 2, 3
DVI INPUT TERMINAL
5 BNC INPUT JACKS
AUDIO INPUT JACKS
Connect an audio output
from computer or video
equipment to these jacks.
(Refer to P14, 15.)
Connect component video output (Cr, Y,
Cb or Pr, Y, Pb) from video equipment to
R/Pr, G/Y and B/Pb jacks or connect
computer output [5 BNC Type (Red,
Green, Blue, Horiz. Sync and Vert.
Sync.)] from computer to R/Pr, G/Y,
B/Pb, H/HV and V jacks. (Refer to P14,
15)
Connect computer output
(Digital/Analog DVI-I type) to
this terminal.
(Refer to P14.)
AUDIO
CONTROL PORT
DVI
R
L
(MONO)
AUDIO
CONTROL PORT
R/Pr
G/Y
B/Pb
H/HV
V
R
L
INPUT 1, 2
CONTROL PORT CONNECTORS
(MONO)
When controlling computer
with Remote Control of this
projector, connect mouse port
of your personal computer to
these connectors.
AUDIO
R
S-VIDEO
C
VIDEO/Y
L
(MONO)
AUDIO OUT
(Refer to P14.)
USB
SERIAL PORT OUT
SERIAL PORT IN
R
L
R/C JACK
RESET
(MONO)
INPUT 3
INPUT 3
S-VIDEO INPUT JACK
AV INPUT (VIDEO/Y, C) JACKS
Connect S-VIDEO output from
video equipment to this jack.
(Refer to P15.)
Connect composite video output from
video equipment to VIDEO/Y jack or
connect Separate Y/C video outputs to
VIDEO/Y and C jacks. (Refer to P15.)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
SERIAL PORT
IN TERMINAL
SERIAL PORT
OUT TERMINAL
This terminal outputs signal from
SERIAL PORT IN. More than two
projectors can be controlled with one
computer by connecting SERIAL PORT
IN. of another projector to this terminal.
If you control a projector by computer,
you must connect a cable (not provided)
from your computer to this terminal.
AUDIO
CONTROL PORT
DVI
R
L
(MONO)
AUDIO
CONTROL PORT
R/Pr
G/Y
B/Pb
H/HV
V
R
L
(MONO)
AUDIO
R
S-VIDEO
C
VIDEO/Y
L
USB PORT (Series B)
(MONO)
This port is used to control a projector
with computer. It is also used to
control computer with Remote Control
of this projector.
AUDIO OUT
USB
SERIAL PORT OUT
SERIAL PORT IN
R
L
R/C JACK
(Refer to P41, 43.)
Connect USB port of computer to this
port.
REET
(MONO)
AUDIO OUTPUT JACKS
R/C JACK
When using Wired / Wireless Remote
Control Unit as Wired Remote
Control, Connect Wired Remote
Control Unit to this jack with Remote
Control Cable (supplied). (Refer to
page 17.)
Connect an external audio
amplifier to these jacks.
(Refer to P14, 15.)
RESET BUTTON
This projector uses a micro processor to control a
unit. Occasionally, this micro processor may
malfunction and need to be reset. This can be done
by pressing RESET button with a pen, which will
shut down and restart unit. Do not use RESET
function excessively.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
CONNECTING TO COMPUTER
Cables used for connection (✽ = Cables are not supplied with this projector.)
•
•
DVI-VGA Cable
NOTE :
Control Cable for PS/2 port, Serial port, or ADB port
When connecting cable, power cords of both
a
• DVI Cable
• BNC Cable (BNC x 5) ✽
• Audio Cables (RCA x 2) ✽
projector and external equipment should be
disconnected from AC outlet. Turn a projector
and peripheral equipment on before computer is
switched on.
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA / WXGA / UXGA
Desktop type
Laptop type
Monitor Output
Monitor Output
Monitor Output Audio Output
Serial port PS/2 port ADB port
Control Cable Control Cable
for PS/2 Port for ADB Port
Control Cable
for Serial Port
Audio Cable
(stereo) ✽
Terminal
Terminal
Terminal
DVI Cable
BNC Cable ✽
DVI-VGA Cable
Use one of these Control
Cables corresponding
with terminal of your
computer.
AUDIO
CONTROL PORT
DVI
R
L
(MONO)
AUDIO
CONTROL PORT
R/Pr
G/Y
B/Pb
H/HV
V
R
L
(MONO)
Terminals of
a Projector
AUDIO
S-VIDEO
C
VIDEO/Y
R
L
(MONO)
AUDIO OUT
USB
SERIAL PORT OUT
SERIAL PORT IN
R/C JACK
R
L
RESET
(MONO)
AUDIO OUT
Audio Cable
(stereo) ✽
Audio Input
External Audio Equipment
Audio Speaker
(stereo)
Audio Amplifier
14
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
Cables used for connection
• Video Cable (BNC x 1, BNC x 2 or BNC x 3) ✽
• S-VIDEO Cable ✽
NOTE :
When connecting cable, power cords of both a
projector and external equipment should be
disconnected from AC outlet. Turn a projector
and peripheral equipment on before computer is
switched on.
• Audio Cable (RCA x 2) ✽
(✽ = Cables are not supplied with this projector.)
Component video output equipment.
(such as DVD player or
Video Source (example)
Video Cassette Recorder
Video Disc Player
high-definition TV source.)
Composite
Video Output
Separate Y/C
Video Output
Component Video Output
Pr/Cr
Pb/Cb
S-VIDEO Output
Audio Output
Y
R
L
Y
C
Video
Cable ✽
S-VIDEO
Cable ✽
Audio Cable
(Stereo) ✽
Video
Cable ✽
Video
Cable ✽
S-VIDEO
AV AUDIO IN
Pr/Cr-Y-Pb/Cb
Y-C
VIDEO
AUDIO
CONTROL PORT
DVI
R
L
(MONO)
AUDIO
CONTROL PORT
R/Pr
G/Y
B/Pb
H/HV
V
R
L
Terminals of
a Projector
(MONO)
AUDIO
S-VIDEO
C
VIDEO/Y
R
L
(MONO)
AUDIO OUT
USB
SERIAL PORT OUT
SERIAL PORT IN
R
L
R/C JACK
RESET
(MONO)
AUDIO OUT
Audio Cable
(Stereo) ✽
Audio Input
External Audio Equipment
Audio Amplifier Audio Speaker (stereo)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
TOP CONTROLS AND INDICATORS
This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.
TOP CONTROL AND
INDICATORS
POWER ON–OFF BUTTON
FOCUS BUTTONS
VOLUME BUTTONS
INPUT BUTTONS
Used to adjust volume.
(P24)
Used to select input
source. (P25)
Used to adjust focus.
(P22)
Used to turn a projector
on or off. (P21)
LAMP REPLACE INDICATOR
Turns to yellow when
life of a projection lamp
draws to an end. (P45-
47, 50)
ZOOM BUTTONS
Used to adjust zoom.
(P22)
ON--OFF
WARNING TEMP. INDICATOR
Flashes red when
VOLUME
INPUT
FOCUS
ZOOM
internal
temperature is too
high. (P43, 50)
projector
AUTO PC ADJ. BUTTON
Use to operate AUTO
PC Adjustment function.
(P28)
READY INDICATOR
LENS
SHIFT
AUTO
PC ADJ.
SELECT
MENU
IMAGE
Lights green when a
projector is ready to be
LAMP
REPLACE
WARNING
TEMP.
READY
LAMP
turned on.
And it
flashes green in Power
Management mode.
(P40, 50)
IMAGE BUTTON
Used to select image
level. (P31, 36)
LAMP INDICATOR
SELECT BUTTON
Becomes dim when a
projector is turned on.
And bright when a
projector is in stand-by
mode. (P50)
Used to execute item
selected. It is also used
to expand / compress
image in DIGITAL
ZOOM mode. (P33)
LENS SHIFT BUTTON
MENU BUTTON
Used to select LENS SHIFT
function. (P22)
Used to open or close
MENU operation. (P19,
20)
POINT BUTTONS
Used to select an item or adjust
value in ON-SCREEN MENU. They
are also used to pan image in
DIGITAL ZOOM +/– mode. (P33)
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATION OF REMOTE CONTROL
LASER POINTER (Drag ON)
INDICATOR
Lights red while laser beam
is emitted from Laser Light
Window.
Left Side
POWER ON-OFF BUTTON
Used to turn projector on or
off. (P21)
AUTO PC ON-OFF
Lights green when drag ON
position. (P43)
AUTO PC ADJ. BUTTON
D.ZOOM FREEZE NO SHOW
Use to operate AUTO PC
Adjustment function. (P28)
MUTE
IMAGE
MUTE BUTTON
VOLUME
-
VOLUME+
SELECT
Used to mute sound. (P24)
IMAGE BUTTON
Used to select image
level. (P31, 36)
MENU
KEYSTONE
DRAG ON/OFF BUTTON
Used to select drag ON/OFF
position. (P43)
ALL-OFF SWITCH
KEYSTONE BUTTON
Used to correct keystone
distortion. (P22, 39)
When using Remote Control Unit,
turn this switch to “ON.” And turn it
to “ALL OFF” when it is not used.
LEFT CLICK BUTTON
Used as a PC mouse in
Wireless Mouse Operation.
Press this button and the
mouse pointer button to drag
a selected screen object.
(P43)
INSIDE THE BATTERY
COMPARTMENT BOX
This remote control provide the DIP
switches into the battery compartment
box.
Slide the SW4 (LASER ON/OFF
switch) to "OFF" position. The laser
pointer function is not operated.
Set switches 1-3 as shown in table
below depending on Code No. that you
want to select remote control code.
(Refer to P41.)
MOUSE POINTER
Used as a PC mouse in
Wireless Mouse Operation.
(P43)
LASER
P-TIMER
RIGHT CLICK BUTTON
LASER BUTTON
INPUT
INPUT
1
Used as a PC mouse in
Wireless Mouse Operation.
(P43)
Used to operate Laser Pointer
Function. Laser beam is
emitted while pressing this
button within 1 minute.
ZOOM
2
When using this Laser Pointer
INPUT
3
LENS SHIFT BUTTON
Used to select LENS
SHIFT function. (P22)
for more than
1
minute,
release LASER button and
press it again.
FOCUS LENS
DIP SWITCH SETTING
SW4 ........ LASER ON/OFF
SW1 SW2 SW3 Code No.
WIRED REMOTE JACK
ON
ON
ON
ON
ON
OFF ON
ON
Code 1
Code 2
Code 3
FOCUS BUTTON
Used to adjust focus. (P22)
When using as Wired
Remote Control, connect
Remote Control Cable
(supplied) to this jack.
Battery installation is
required when using as
Wired Remote Control.
OFF
ON
OFF OFF
Code 4
Code 5
Code 6
Code 7
Code 8
OFF ON
OFF ON
ON
OFF
OFF OFF ON
OFF OFF OFF
LASER POINTER FUNCTION
This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is
pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released,
light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being
emitted.
Laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other
people. Three marks below are caution labels for laser beam.
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result
hazardous radiation exposure.
These caution labels are put on remote control.
LASER POINTER INDICATOR
Laser Light Window
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
NO SHOW BUTTON
Used to turn picture into
black image. (P23)
D.ZOOM BUTTON
Operating Range
Used to select DIGITAL
ZOOM +/– mode and
resize image. (P33)
Point Remote Control Unit toward
projector (Infrared Receiver Window)
whenever pressing any button.
Maximum operating range for
Remote Control Unit is about 16.4’
(5m) and 60° in front and rear of a
projector.
AUTO PC ON-OFF
D.ZOOM FREEZE NO SHOW
SELECT BUTTON
MUTE
IMAGE
FREEZE BUTTON
Used to freeze picture. (P23)
Used to execute the
selected item, or to
expand or compress
image in DIGITAL ZOOM
+/- mode. (P33)
VOLUME
-
VOLUME+
SELECT
POINT (VOLUME +/-)
BUTTONS
MENU
KEYSTONE
Used to select an item or
adjust value in ON-SCREEN
MENU. They are also used
to pan image in DIGITAL
ZOOM +/- mode. (P33)
POINT LEFT/RIGHT buttons
are also used as VOLUME
+/- buttons. (P24)
60°
MENU BUTTON
Used to select MENU
operation. (P19, 20)
16.4’
(5 m)
INPUT 1 BUTTON
P-TIMER BUTTON
Used to select input
source (INPUT 1).
(P25)
LASER
P-TIMER
Used to operate P-
TIMER function. (P23)
INPUT
INPUT
1
INPUT 2 BUTTON
ZOOM
2
Used to select input
source (INPUT 2).
(P25, 34)
ZOOM BUTTON
INPUT
3
Used to adjust zoom. (P22)
FOCUS LENS
INPUT 3 BUTTON
Used to select input
source (INPUT 3).
(P34)
16.4’
(5 m)
60°
REMOTE CONTROL BATTERIES INSTALLATION
Remove battery
compartment lid.
Slide batteries into
compartment.
Replace compartment lid.
1
2
3
Two AA size batteries
Press lid down-
ward and slide it.
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
To insure safe operation, please observe following precautions :
● Use (2) AA or R06 type alkaline batteries.
● Replace two batteries at same time.
● Do not use a new battery with an used battery.
● Avoid contact with water or liquid.
● Do not expose Remote Control Unit to moisture, or heat.
● Do not drop Remote Control Unit.
● If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.
● Danger of explosion if battery is incorrectly replaced.
● Dispose of used batteries according to batteries manufacturers instructions and local rules.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
REMOTE CONTROL UNIT
You can control and adjust this projector through ON-SCREEN
MENU. Refer to following pages to operate each adjustment on
ON-SCREEN MENU.
AUTO PC ON-OFF
1 DISPLAY MENU
Press MENU button to display ON-SCREEN MENU.
D.ZOOM FREEZE NO SHOW
POINT BUTTONS
Used to move the
Pointer UP/ DOWN/
RIGHT/ LEFT.
MUTE
IMAGE
2 MOVING POINTER
VOLUME
-
VOLUME+
SELECT
Move pointer (✽ see below) or adjust value of item by pressing
POINT button(s) on Top Control or on Remote Control Unit.
MENU
KEYSTONE
✽ Pointer is a icon on ON-SCREEN MENU to select item. See fig-
ures on section "FLOW OF ON-SCREEN MENU OPERATION"
below.
SELECT BUTTON
Used to select the item.
MENU BUTTON
TOP CONTROL
3 SELECT ITEM
POINT BUTTONS
Used to move Pointer
UP/ DOWN/ RIGHT/
LEFT.
Select item or set selected function by pressing SELECT button.
VOLUME
INPUT
FOCUS
OOM
MENU BUTTON
LENS
SHIFT
UTO
C ADJ.
SELECT
MENU
IMAGE
SELECT BUTTON
Used to select item.
FLOW OF ON-SCREEN MENU OPERATION
MENU BAR
MENU ICON
Display ON-SCREEN MENU
Press MENU button to display ON-SCREEN MENU (MENU
BAR). A red frame is POINTER.
1
POINTER
(red frame)
POINTER (red frame)
Press POINT DOWN button to
move POINTER.
Select Menu to be adjusted
Move POINTER (red frame) to MENU ICON that you want to
select by pressing POINT RIGHT / LEFT buttons.
2
ITEM
Control or adjust item through ON-SCREEN MENU
Press POINT DOWN button and move POINTER (red frame
or red arrow) to ITEM that you want to adjust, and then press
SELECT button to show ITEM DATA.
3
SELECT
BUTTON
Adjust ITEM DATA by pressing POINT RIGHT / LEFT
buttons.
Refer to following pages for details of respective
adjustments.
4
ITEM DATA
Press POINT LEFT/RIGHT
buttons to adjust value or
set function.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE OPERATION
MENU BAR
FOR PC SOURCE
Press MENU BUTTON while connecting to PC input source.
IMAGE SELECT MENU
SCREEN MENU
SETTING MENU
Used to select
Used to adjust size
of image. [Normal
/Full/True/Digital
zoom +/–]
Used to change
settings of projector
or reset Lamp
Replace Counter.
(Refer to P39-42)
GUIDE WINDOW
PC SYSTEM MENU
image level among
Standard, Real
and Image 1 ~ 4.
(Refer to P31)
Shows selected
item of ON-
SCREEN MENU.
Used to select
computer system.
(Refer to P26-28)
(Refer to P33)
INPUT MENU
PC ADJUST MENU
IMAGE ADJUST MENU
SOUND MENU
Used to select
Used to adjust
parameters to
match with input
signal format.
Used to adjust
Used to adjust
sound [volume,
Bass or Treble],
to select Built-in
SP On-Off and
Sound Mute.
input source (Input
1, Input 2 or Input
3). (Refer to P25)
computer image.
[Contrast/Brightness
/Color Temp.
/White Balance (R/G/B)
/Sharpness/Gamma
/Noise Reduction
/Progressive]
(Refer to P28-30)
(Refer to P24)
(Refer to P32)
FOR VIDEO SOURCE
Press MENU BUTTON while connecting to VIDEO input source.
SCREEN MENU
Used to set size of
image to Full,
Zoom, Normal or
Natural wide.
(Refer to P38)
INPUT MENU
IMAGE SELECT MENU
Used to select
Used to select image
level among
Standard, Cinema
and Image 1 ~ 4.
(Refer to P36)
input source (Input
1, Input 2 or Input
3). (Refer to P34)
AV SYSTEM MENU
IMAGE ADJUST MENU
Same function as
Menu for PC source.
Same function as
Menu for PC source.
Used to select
system of selected
video source.
Used to adjust picture image.
[Contrast/Brightness/Color
/Tint/Color Temp.
(Refer to P35)
/White balance (R/G/B)
/Sharpness/Gamma
/Noise Reduction/Progressive]
(Refer to P37, 38)
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
TURNING ON / OFF PROJECTOR
TURNING ON PROJECTOR
Complete peripheral connections (with Computer, VCR, etc.)
before turning on projector. (Refer to "CONNECTING TO
PROJECTOR" on Pages 12~15 for connecting that equipment.)
1
LAMP STATUS
INPUT 1
1
2
Connect a projector's AC Power Cord into a wall outlet and turn
MAIN ON / OFF SWITCH to ON. LAMP indicator lights RED,
and READY indicator lights GREEN.
2
3
30
Press POWER ON-OFF button on Top Control or on Remote
Control Unit to ON. LAMP indicator dims, and Cooling Fans start
to operate. Preparation Display appears on a screen and count-
down starts. Signal from source appears after 30 seconds.
Current Input position and Lamp status are also displayed on
screen for 5 seconds. (Refer to "LAMP MANAGEMENT" on
page 45.)
Preparation Display disappears after
30 seconds.
TURNING OFF PROJECTOR
Press POWER ON-OFF button on Top Control or on Remote
Control Unit, and a message "Power off?" appears on a screen.
1
2
Press POWER ON-OFF button again to turn off projector. LAMP
indicator lights bright and READY indicator turns off. After
approximate 90 seconds, READY indicator will light green again
and projector may be turned on by pressing POWER ON-OFF
button.
Power off?
Cooling fans will operate for approximate 2 minutes after projec-
tor is turned off. To power down completely, turn MAIN ON/OFF
SWITCH to OFF and disconnect AC Power Cord.
Message disappears after 4 seconds.
3
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
When Power Management function mode is Ready or Shut down, projector detects signal interruption and turns off
Projection Lamp automatically. Refer to “Power Management” on pages 39 and 40.
When WARNING TEMP. indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on
projector again.
When both WARNING TEMP. and READY indicators to flash, follow procedures below:
1. Turn MAIN ON / OFF SWITCH to OFF.
2. Turn a projector on again.
When WARNING TEMP. indicator continues to flash, follow procedures below:
1. Turn MAIN ON / OFF SWITCH to OFF and disconnect AC Power Cord from an AC outlet.
2. Check Air Filters for dust accumulation.
3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 44.)
4. Turn a projector on again.
If WARNING TEMP. indicator should still continue to flash, contact sales dealer where you purchased this projector or
service center.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
ADJUSTING SCREEN
ZOOM ADJUSTMENT
Press ZOOM ▲/▼ button on Top Control or on Remote Control
Unit. Message “Zoom” is displayed.
1
2
Press ZOOM ▲ button to make image larger, and press ZOOM
▼ button to make image smaller.
Zoom
Message disappears after 4 seconds.
FOCUS ADJUSTMENT
Press FOCUS ▲/▼ button on Top Control or on Remote Control
Unit. Message “Focus” is displayed.
1
2
Adjust focus of image by pressing FOCUS ▲/▼ button(s) .
Focus
Message disappears after 4 seconds.
LENS SHIFT ADJUSTMENT
Press LENS SHIFT button on Top Control or on Remote Control
Unit. Message “Lens shift” is displayed.
1
2
Press POINT UP button to move image up, press POINT DOWN
button to move image down.
Lens shift
Message disappears after 4 seconds.
KEYSTONE ADJUSTMENT
If a projected picture has keystone distortion, correct image with KEYSTONE adjustment.
Press KEYSTONE button on Remote Control Unit or select
Keystone on SETTING menu. (Refer to page 39.) Keystone
dialog box appears.
1
Message disappears after 4 seconds.
Correct keystone distortion by pressing POINT LEFT/RIGHT
button(s). Press POINT LEFT button to reduce left part of
image, and press POINT RIGHT button to reduce right part.
2
• If you press the KEYSTONE button on Remote
Control Unit once more while the keystone dialog box
is being displayed, the keystone adjustment will be
canceled.
• Keystone function can not be operated when
"NATURAL WIDE" is selected on PICTURE SCREEN
ADJUSTMENT (P38).
Reduce the left part with
Point Left button.
Reduce the right part with
Point Right button.
• If you select "NATURAL WIDE" after adjusting the
keystone, the adjustment will be canceled.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
PICTURE FREEZE FUNCTION
Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE
button again or press any other button except POINT / SELECT / RIGHT CLICK / LASER button.
NO SHOW FUNCTION
Press NO SHOW button on Remote Control Unit to black out a image.
To restore to normal, press NO SHOW button again or press any other
button except POINT / SELECT / RIGHT CLICK / LASER button.
No show
Message disappears after 4 seconds.
P-TIMER FUNCTION
Press P-TIMER button on Remote Control unit. Timer display “00 : 00”
appears on a screen and timer starts to count time (00 : 00 ~ 59 : 59).
To stop P-TIMER display, press P-TIMER button. And then, press P-TIMER
button again to cancel P-TIMER function.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATION
SOUND ADJUSTMENT
Indicates roughly level of
volume.
DIRECT OPERATION
Volume
Press VOLUME (+/–) button(s) on Top Control or on Remote Control
Unit to adjust volume. Volume dialog box appears on screen for a few
seconds.
(+) button to increase volume, and (–) button for decreasing.
Mute
Press MUTE button on Remote Control Unit to cut off sound. To
restore sound to its previous level, press MUTE button again or press
Volume (+/–) button(s).
Press MUTE button to set
Mute function On or Off.
Display disappears after 4 seconds.
MENU OPERATION
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SOUND Menu icon.
SOUND MENU
1
Press POINT DOWN button to move a red frame pointer to item
that you want to select, and then press SELECT button.
2
SOUND Menu icon
Indicates roughly
level of volume.
Volume
On
Press POINT LEFT/RIGHT buttons
to adjust value.
To increase volume, press POINT RIGHT button, and press POINT
LEFT button for decreasing.
Close SOUND Menu.
Treble
To adjust Treble sound, press POINT RIGHT button or POINT LEFT
button.
Bass
To adjust Bass sound, press POINT RIGHT button or POINT LEFT
button.
Built-in SP.
Press POINT LEFT/RIGHT button(s) to switch built-in speaker on and
off.
Mute
Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box
display is changed to “On” and sound is cut off. To restore sound to
its previous level, press POINT LEFT/RIGHT button(s) again.
Quit
Closes SOUND MENU.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
SELECTING INPUT SOURCE
INPUT 1 button
INPUT ▲/▼ buttons
INPUT 1
DIRECT OPERATION
Select INPUT source by pressing INPUT 1, INPUT 2 and
INPUT 3 buttons on Remote Control Unit.
INPUT 1
INPUT 2 button
INPUT 2
Select INPUT source by pressing INPUT ▲/▼ button on Top
INPUT 2
Control.
INPUT 3 button
INPUT 3
INPUT 3
MENU OPERATION
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to select Input and press SELECT
1
button.
Menu will appear.
Another dialog box INPUT SELECT
INPUT Menu icon
Press POINT DOWN button to move arrow to INPUT source that
you want to select, and then press SELECT button.
2
SELECTING COMPUTER SYSTEM
WHEN SELECT INPUT 1 (DVI INPUT TERMINAL )
INPUT MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
1
2
3
INPUT Menu icon
Press POINT DOWN button to move a red arrow pointer to Input
1 and then press SELECT button. Source Select Menu will
appear.
Move a pointer (red arrow) to
Input 1 and press SELECT
button.
Move a pointer to either Digital or Analog and then press
SELECT button.
Input 1
Source Select Menu
When digital signal is connected on DVI terminal, select
Digital.
Move a pointer to Digital or
Analog and press SELECT
button.
Digital
When analog signal is connected on DVI terminal, select
Analog.
Analog
WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )
When connect a computer output [5 BNC Type (Red, Green, Blue,
Horiz. Sync and Vert. Sync.)] from a computer to R/Pr, G/Y, B/Pb, H/HV
and V jacks.
INPUT MENU
INPUT Menu icon
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
1
Move a pointer (red arrow) to
Input 2 and press SELECT
button.
Press POINT DOWN button to move a red arrow pointer to Input
2 and then press SELECT button. Source Select Menu will
appear.
Input 2
2
Source Select Menu
Move a pointer to RGB and
press SELECT button.
Move a pointer to "RGB", and then press SELECT button.
3
25
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
AUTOMATIC MULTI-SCAN SYSTEM
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, SXGA, WXGA or UXGA
(refer to “COMPATIBLE COMPUTER SPECIFICATIONS” on page 27). When selecting Computer, this projector
automatically tunes to incoming signal and projects proper image without any special setting. (Some computers need setting
manually.)
Note : Projector may display one of following messages.
When projector cannot recognize connected signal as PC
system provided in this projector, Auto PC Adjustment
function operates to adjust projector and message “Auto”
is displayed on SYSTEM Menu icon. (Refer to P28.)
When image is not provided properly, manual adjustment
is required. (Refer to P29 and 30.)
PC SYSTEM MENU
Auto
PC SYSTEM Menu icon
Displays system being
selected.
There is no signal input from computer. Make sure
connection of computer and a projector is set correctly.
(Refer to TROUBLESHOOTING on page 48.)
––––
D-VGA, D-SVGA, D-XGA, D-SXGA 1, D-SXGA 2, D-SXGA3 or D-UXGA
When digital computer signal is received on DVI terminal,
above message is displayed on PC SYSTEM Menu icon.
SELECT COMPUTER SYSTEM MANUALLY
This projector automatically selects PC system among those provided
in this projector and PC system can be also selected manually.
PC SYSTEM MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to PC
SYSTEM Menu icon.
1
PC SYSTEM Menu icon
Displays system being selected.
Press POINT DOWN button to move a red arrow pointer to
2
Systems on this dialog box can
be selected.
system that you want to set, and then press
SELECT button.
Custom Mode (1~5) set in PC
ADJUST Menu. (P29, 30)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less
than 230 MHz of Dot Clock.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
VGA 1
VGA 2
VGA 3
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
480i
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
15.734
15.625
31.47
31.25
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
56.476
60.31
48.50
44.00
63.48
36.00
62.04
61.00
35.522
46.90
47.00
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
60.00
50.00
59.88
50.00
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
87.17
77.07
75.70
86.96
58.20
58.30
XGA15
MAC 19
MAC 21
SXGA 1
SXGA 2
SXGA 3
SXGA 4
SXGA 5
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
SXGA 13
SXGA 14
SXGA 15 1280 x 1024
SXGA 16 1280 x 1024
SXGA 17
SXGA 18
SXGA 19 1280 x 1024
SXGA 20 1280 x 1024
SXGA 21 1400 x 1050
MAC
MAC
1024 x 768
1024 x 768
1152 x 870
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1152 x 900
1152 x 900
58.03
60.24
68.68
64.20
62.50
63.90
63.34
63.74
71.69
81.13
63.98
79.976
60.00
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
63.79
91.146
63.90
75.00
80.00
48.36
47.70
48.36
56.16
75.00
81.25
87.50
93.750
45.00
33.75
33.75
28.125
72.0
75.08
75.06
70.40
58.60
60.00
59.98
60.01
67.19
76.107
60.02
75.025
60.00
65.20
75.60
86.00
94.00
60.01
72.00
66.00
86.70
60.18
85.024
60.00
75.08
75.08
60.00
60.00
60.00
72.00
60.00
65.00
70.00
75.00
60.00
60.00
60.00
50.00
––––––––
(Interlace)
––––––––
(Interlace)
––––––––
(Progressive)
––––––––
(Progressive)
575i
480p
575p
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
XGA 2
XGA 3
XGA 4
XGA 5
XGA 6
XGA 7
XGA 8
XGA 9
XGA 10
XGA 11
XGA 12
XGA 13
XGA 14
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
(Interlace)
1280 x 1024
(Interlace)
1152 x 900
1280 x 1024
(Interlace)
1280 x 960
1280 x 1024
1366 x 768
1360 x 768
1376 x 768
1360 x 768
1600 x 1200
1600 x 1200
1600 x 1200
1600 x 1200
WXGA 1
WXGA 2
WXGA 3
WXGA 4
UXGA 1
UXGA 2
UXGA 3
UXGA 4
720p
1024 x 768
(Interlace)
––––––––
(Progressive)
––––––––
(Interlace)
––––––––
(Interlace)
1024 x 768
1024 x 768
1035i
1080i/60
1080i/50
1024 x 768
(Interlace)
––––––––
(Interlace)
1024 x 768
1024 x 768
27
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
When a input signal is digital from DVI terminal, refer to chart below.
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
H-Freq.
(kHz)
V-Freq.
(Hz)
RESOLUTION
RESOLUTION
D-VGA
D-SVGA
D-XGA
640 x 480
800 x 600
1024 x 768
31.469
37.879
48.363
63.981
59.940
60.317
60.004
60.020
D-SXGA 2 1280 x 1024
D-SXGA 3 1280 x 1024
60.276
31.65
75.00
58.069
29.8
D-UXGA
1600 x 1200
60.00
D-SXGA 1 1280 x 1024
NOTE : Specifications are subject to change without notice.
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your
computer. Auto PC Adjustment function can be operated as follows.
Auto PC Adj.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.
PC ADJUST MENU
1
2
Press POINT DOWN button to move a red frame pointer to
AUTO PC Adj. icon and then press SELECT button twice.
This Auto PC Adjustment can be also executed by pressing
AUTO PC ADJ. button on Top Control or on Remote Control
Unit.
PC ADJUST Menu icon
Move a red frame pointer to AUTO PC
Adj. icon and press SELECT button.
Store adjustment parameters.
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector. Once parameters are memorized, setting can be
done just by selecting Mode in PC SYSTEM Menu (P26). Refer to
step 3 of MANUAL PC ADJUSTMENT section (P30).
NOTE
● Fine sync, Total dots and Picture Position of some computers can
not be fully adjusted with this Auto PC Adjustment function. When
image is not provided properly through this function, manual
adjustments are required. (Refer to page 29, 30.)
● Auto PC Adjustment function cannot be operated in Digital Signal
input on DVI terminal and “480i”, “575i”, “480p”, “575p”, “720p
(HDTV)”, “1035i (HDTV)”, “1080i50 (HDTV)” or “1080i60 (HDTV)” is
selected on PC SYSTEM Menu (P26).
28
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to display signals from most personal computers currently distributed. However, some
computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system
of this projector. If this happens, projector cannot reproduce a proper image and image may be recognized as a flickering
picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special
signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This
enables you to recall setting for a specific computer whenever you use it.
Note : This PC ADJUST Menu cannot be operated in Digital Signal input on DVI terminal is selected on PC SYSTEM MENU
(P26).
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.
PC ADJUST MENU
1
2
Press POINT DOWN button to move a red frame pointer to item
that you want to adjust and then press SELECT button.
Adjustment dialog box will appear. Press POINT LEFT/RIGHT
button to adjust value.
PC ADJUST Menu icon
Move a red frame pointer to item and
press SELECT button.
Fine sync
Adjusts an image as necessary to eliminate flicker from display.
Press POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)
Shows status
Total dots
(Stored / Free) of
Selected Mode
selected Mode.
Number of total dots in one horizontal period. Press POINT
LEFT/RIGHT button(s) and adjust number to match your PC image.
Horizontal
Adjusts horizontal picture position. Press POINT LEFT/RIGHT
button(s) to adjust position.
Press POINT LEFT/RIGHT
button to adjust value.
Vertical
Adjusts vertical picture position. Press POINT LEFT/RIGHT
button(s) to adjust position.
Press SELECT button at this icon to
adjust “Clamp,” “Display area (H/V)” or
set “Full screen.”
Current mode
Press SELECT button to show information of computer selected.
Clamp
Current mode
Adjusts clamp position. When a image has a dark bar(s), try this
adjustment.
Press SELECT button at
Current mode icon to show
information of computer
connected.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
Display area
Selects area displayed with this projector. Select resolution at
Display area dialog box.
Press SELECT button at
Display area icon and Display
area dialog box appears.
Display area H
Display area
Adjustment of horizontal area displayed with this projector. Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Display area V
Adjustment of vertical area displayed with this projector. Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Press POINT LEFT
/RIGHT button(s) to
adjust value and then
press SELECT button.
Full screen
Press POINT LEFT/RIGHT button(s) to switch Full screen function to
“On” or “Off.” Set “On” to resize image to fit the horizontal size of the
screen.
NOTE : Fine sync, Display area, Display area H, Display area V and
Full screen can not be adjusted when “480i”, “575i”, “480p”,
“575p”, “720p (HDTV)”, “1035i (HDTV)”, “1080i50(HDTV)” or
“1080i60 (HDTV)” is selected on PC SYSTEM Menu (P26).
To store adjustment data.
This Mode has parameters being stored.
Store
3
To store adjustment parameters, move a red frame pointer to
Store icon and then press SELECT button. Move a red arrow
pointer to any of Mode 1 to 5 that you want to store and then
press SELECT button.
Mode free
To clear adjustment parameters previously set, move a red
frame pointer to Mode free icon and then press SELECT button.
Move a red arrow pointer to Mode that you want to clear and
then press SELECT button.
Vacant Mode
Store icon
Shows values of “Total dots,”
“Horizontal,” “Vertical,” “Display
area H,” and “Display area V.”
Other icons operates as follows.
Reset
To clear adjustment data.
Reset all adjust parameters on adjustment dialog box to previous
figure.
Quit
Closes PC ADJUST MENU.
Close this dialog box.
Mode free icon
30
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Real, Image 1, Image 2, Image 3
IMAGE button
and Image 4 by pressing IMAGE button on Top Control or on Remote
Control Unit.
Standard
Real
Standard
Normal picture level preset on this projector.
Image 1
Image 2
Image 3
Image 4
Real
Picture level with improved halftone for graphics.
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P32).
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.
IMAGE SELECT MENU
1
2
Press POINT DOWN button to move a red frame pointer to level
that you want to set and then press SELECT button.
IMAGE SELECT
Menu icon
Standard
Normal picture level preset on this projector.
Move a red frame pointer to level
and press SELECT button.
Real
Picture level with improved halftone for graphics.
IMAGE 1~4
Level being selected.
User preset picture adjustment in IMAGE ADJUST Menu (P32).
31
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
IMAGE LEVEL ADJUSTMENT
Press MENU button and ON-SCREEN MENU will appear. Press
1
2
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE ADJUST MENU
IMAGE ADJUST Menu icon.
Press POINT DOWN button to move a red frame pointer to item
that you want to adjust and then press SELECT button. Level of
each item is displayed. Adjust each level by pressing POINT
LEFT/RIGHT button(s).
IMAGE ADJUST
Menu icon
Move a red frame pointer to
item to be selected and then
press SELECT button.
Contrast
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)
Selected Image level
Color temp.
Press either POINT LEFT button or POINT RIGHT button to Color
temp. level that you want to select. (XLow, Low, Mid or High)
White balance (Red)
Press POINT LEFT/RIGHT buttons
to adjust value.
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Green)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Blue)
Store icon
Press SELECT button at this icon to
store adjustment.
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Sharpness
Press POINT LEFT button to soften image, and POINT RIGHT
button to sharpen image. (From 0 to 15.)
Gamma
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)
Noise reduction
Image Level Menu
Press POINT LEFT/RIGHT button(s) to change noise reduction
mode. Dialog box display is changed to “On” to reduce noise (rough
parts) of image. Press POINT LEFT/RIGHT button(s) again, to
change noise reduction mode to off.
Move a red frame pointer to any
of Image 1 to 4 where you want
to set and then press SELECT
button.
Progressive
Press POINT LEFT/RIGHT button(s) to change progressive scan
mode. Dialog box display is changed to “Off” and progressive scan
mode to off. Press POINT LEFT/RIGHT button(s) again, progressive
scan mode to on.
Store
3
To store manually preset image, move a red frame pointer to
Store icon and press SELECT button. Image Level Menu will
appear. Move a red frame pointer to Image 1 to 4 where you
want to set and then press SELECT button.
NOTE :
● Noise reduction can be operated when “480i”,
“575i”, “480p”, “575p”, “720p (HDTV)”, “1035i
(HDTV)”, “1080i50 (HDTV)” or “1080i60 (HDTV)”
is selected on PC SYSTEM MENU (P26) only.
Other icons operates as follows.
Reset
Reset all adjustment to previous figure.
● Progressive can be operated when “480i”,
“575i”, “1035i (HDTV)”, “1080i50 (HDTV)” or
“1080i60 (HDTV)” is selected on PC SYSTEM
MENU (P26) only.
Quit
Closes IMAGE MENU.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display desirable image size.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
SCREEN MENU
1
2
Press POINT DOWN button and move a red frame pointer to
function that you want to select and then press SELECT button.
SCREEN Menu icon
Move a red frame pointer to function
and press SELECT button.
Normal
Provides image to fit the panel size of the screen.
Full
Provides image to fit the horizontal size of the screen.
NOTE
True
● Picture screen adjustment can not be operated
when “720p (HDTV)”, “1035i (HDTV)”, “1080i50
(HDTV)” or “1080i60 (HDTV)” is selected on PC
SYSTEM Menu (P26).
Provides image in its original size. When the original image size is
larger than screen size (1366 X 768), this projector enters “D. Zoom
+” mode automatically.
● True and Digital zoom +/- can not be selected
when “480i”, “575i”, “480p” or “575p” is selected on
PC SYSTEM Menu (P26).
Digital zoom +
When Digital zoom + is selected, ON-SCREEN MENU disappears
and message “D. Zoom +” is displayed. Press SELECT button to
expand image size. And press POINT UP/DOWN/LEFT/RIGHT
button(s) to pan image. Panning function can work only when image
is larger than screen size.
A projected image can be also expanded by pressing D.ZOOM ▲
button on Remote Control Unit.
● This projector can not display any resolution higher
than 1600 X 1200. If your computer’s screen
resolution is higher than 1600 X 1200, reset
resolution to lower before connecting projector.
● Image data in other than XGA (1024 x 768) is
modified to fit screen size in initial mode.
● Panning function may not operate properly if
computer system prepared on PC ADJUST Menu
is used.
Digital Zoom –
When Digital zoom – is selected, ON-SCREEN MENU disappears
and message “D. Zoom –” is displayed. Press SELECT button to
compress image size.
A projected image can be also compressed by pressing D.ZOOM ▼
button on Remote Control Unit.
To cancel Digital Zoom +/– mode, press any button except D.ZOOM
▲/▼, SELECT, POINT and AUTO PC ADJ. buttons.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
SELECTING INPUT SOURCE
WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )
When connect component video output (Cr, Y, Cb or Pr, Y, Pb) from
video equipment to R/Pr, G/Y and B/Pb jacks.
INPUT MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
INPUT Menu icon
1
Move a pointer (red arrow) to
Input 2 and press SELECT
button.
Press POINT DOWN button to move a red arrow pointer to Input
2 and then press SELECT button. Source Select Menu will
appear.
2
Input 2
Source Select Menu
Move a pointer to "Y, Pb/Cb, Pr/Cr" and then press SELECT
button.
3
Move a pointer to
Y, Pb/Cb, Pr/Cr and press
SELECT button.
WHEN SELECT INPUT 3 (AV TERMINAL )
When connecting to those equipment, select a type of Video
INPUT MENU
source in SOURCE SELECT (VIDEO) Menu.
INPUT Menu icon
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
1
Move a pointer (red arrow) to
Input 3 and press SELECT
button.
Press POINT DOWN button to move a red arrow pointer to Input
3 and then press SELECT button. Source Select Menu will
appear.
2
Input 3
Source Select Menu (VIDEO)
Move a pointer to source and
press SELECT button.
Move a pointer to source that you want to select and then press
SELECT button.
3
When video input signal is connected to VIDEO jack,
select Video.
Video
When video input signal is connected to S-VIDEO jack,
select S-Video.
S-Video
When video input signal is connected to VIDEO/Y, C
jacks, select Y, C.
Y, C
34
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
SELECTING VIDEO SYSTEM
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to AV
SYSTEM Menu icon.
1
2
Press POINT DOWN button to move a red arrow pointer to
system that you want to select and then press SELECT button.
VIDEO JACK OR S-VIDEO JACK
AV SYSTEM MENU (VIDEO OR S-VIDEO)
Auto
Projector automatically detects incoming Video system, and adjusts
itself to optimize its performance.
When Video System is PAL-M or PAL-N, select system manually first.
AV SYSTEM Menu icon
This box indicates system
being selected.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If projector can not reproduce proper video image, it is necessary to
select a specific broadcast signal format among PAL, SECAM, NTSC,
NTSC 4.43, PAL-M, and PAL-N.
Move pointer to system
and press SELECT
button.
Y, Pb/Cb, Pr/Cr JACKS
AV SYSTEM MENU (COMPONENT VIDEO)
Auto
Projector automatically detects incoming Video signal, and adjusts
itself to optimize its performance.
When Video System is 1035i, 1080i50 or 1080i60, select system
manually first.
Auto
AV SYSTEM Menu icon
This box indicates system
1080i60
1080i50
1035i
720p
575p
480p
575i
being selected.
COMPONENT VIDEO SIGNAL FORMAT
If projector can not reproduce proper video image, it is necessary to
select a specific component video signal format among 480i, 575i,
480p, 575p, 720p, 1035i , 1080i50 or 1080i60.
Move pointer to system
and press SELECT
button.
480i
35
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Cinema, Image 1, Image 2,
Image 3 and Image 4 by pressing IMAGE button on Top Control or on
Remote Control Unit.
IMAGE button
Standard
Cinema
Image 1
Image 2
Image 3
Image 4
Standard
Normal picture level preset on this projector.
Cinema
Picture level adjusted for picture with fine tone.
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P38).
IMAGE LEVEL SELECT (MENU)
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.
IMAGE SELECT MENU
1
2
Press POINT DOWN button to move a red frame pointer to level
that you want to set and then press SELECT button.
IMAGE SELECT
Menu icon
Standard
Normal picture level preset on this projector.
Cinema
Move a red frame pointer to level
and press SELECT button.
Picture level adjusted for picture with fine tone.
IMAGE 1~4
Level being selected.
User preset picture adjustment in IMAGE ADJUST Menu (P38).
36
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
IMAGE LEVEL ADJUSTMENT
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
IMAGE ADJUST Menu icon.
IMAGE ADJUST MENU
1
2
Press POINT DOWN button to move a red frame pointer to item
that you want to adjust and then press SELECT button. Level of
each item is displayed. Adjust each level by pressing POINT
LEFT/RIGHT button(s).
IMAGE ADJUST
Menu icon
Move a red frame pointer to
item to be selected and then
press SELECT button.
Contrast
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)
Color
Press POINT LEFT button to lighten color, and POINT RIGHT button
to deeper color. (From 0 to 63.)
Press POINT LEFT/RIGHT buttons
to adjust value.
Tint
Press POINT LEFT button or POINT RIGHT button to obtain proper
color. (From 0 to 63.)
Press SELECT button at this icon to
display other items.
Color temp.
Press either POINT LEFT button or POINT RIGHT button to Color
temp. level that you want to select. (XLow, Low, Mid or High)
Press SELECT button at this icon to
display previous items.
White balance (Red)
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Green)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Press POINT LEFT/RIGHT buttons
to adjust value.
White balance (Blue)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Sharpness
Press POINT LEFT button to soften image, and POINT RIGHT
button to sharpen image. (From 0 to 15.)
Press SELECT button at this icon to
store value.
Gamma
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)
NOTE :
Tint can not be adjusted when video system is
PAL, SECAM, PAL-M or PAL-N.
Noise reduction
Press POINT LEFT/RIGHT button(s) to change noise reduction
mode. Dialog box display is changed to “On” to reduce noise (rough
parts) of image. Press POINT LEFT/RIGHT button(s) again, to
change noise reduction mode to off.
Progressive can not be operated when “480p”,
“575p”, “720p”, “1035i”, “1080i50” or “1080i60” is
selected on AV SYSTEM MENU (P35).
Progressive scan
Press POINT LEFT/RIGHT button(s) to change progressive scan
mode. Dialog box display is changed to “Off” and progressive scan
mode to off. Press POINT LEFT/RIGHT button(s) again, progressive
scan mode to on.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO INPUT
Store
3
To store adjustment data, move a red frame pointer to Store icon
and press SELECT button. Image Level Menu will appear.
Move a red frame pointer to Image Level 1 to 4 and then press
SELECT button.
Image Level Menu
Other icons operates as follows.
Move a red frame pointer to
image icon to be set and
then press SELECT button.
Reset
Reset all adjustment to previous figure.
Quit
Store icon
Closes IMAGE MENU.
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display desirable image size.
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
SCREEN MENU
1
2
Press POINT DOWN button and move a red frame pointer to
function that you want to select and then press SELECT button.
SCREEN Menu icon
Move a red frame to function and press
SELECT button.
Full
Provides image to fit width of screen by expanding image width
uniformly. This function can be used for providing a squeezed video
signal at wide video aspect ratio of 16 : 9.
When your video equipment (such as DVD) has 16 : 9 output mode,
select 16 : 9 and select Full on this SCREEN Menu to provide better
quality.
NOTE : SCREEN Menu can not be operated when
“720p”, “1035i”, “1080i50” or “1080i60” is
selected on AV SYSTEM Menu (P35).
Zoom
Provides image to fit screen size (16 : 9 aspect ratio) by expanding
image width and height uniformly. This function can be used for
providing a letter box mode picture (4 : 3 aspect picture with black
bar on top and bottom edges) at wide video aspect of 16 : 9.
Normal
Provides image at the normal video aspect ratio of 4 : 3.
Natural wide
Provides image to fit width of screen by expanding both sides of
image. This function is suitable to provide a normal video signal (4 :
3 aspect ratio) at wide video aspect ratio of 16 : 9.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
SETTING MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red-frame pointer to
SETTING icon.
SETTING MENU
1
2
Press POINT DOWN button to move a red-frame pointer to item
Set a red frame
SETTING Menu icon
pointer to item and
press SELECT
button.
that you want to set and then press
SELECT button. Setting
dialog box appears.
Language
Language used in ON-SCREEN MENU is selectable from among
English, German, French, Italian, Spanish, Portuguese, Dutch,
Swedish, Russian, Chinese, Korean and Japanese.
Keystone
When image is distorted horizontally, select Keystone. ON-SCREEN
MENU disappears and Keystone dialog box is displayed.
Correct keystone distortion by pressing POINT LEFT/RIGHT
button(s). Refer to KEYSTONE ADJUSTMENT on page 22.
When pressing SELECT
button at Language,
Language Menu appears.
Blue back
When this function is “On,” this projector will produce a blue image
instead of video noise on screen when any input source is unplugged
or turned off.
Display
This function decides whether to display On-Screen Displays.
On ··· shows all On-Screen Displays.
Off ···· sets On-Screen Displays disappeared except;
● ON-SCREEN MENU
● “Power off?” message
● P-TIMER
● “No signal” message
● “Wait a moment” message
Logo
When this function is “On,” projector displays our logo when starting
up.
Move a pointer to item
and then press POINT
LEFT/RIGHT button(s).
Optional Control Number
Refer to page 11.
Ceiling
When this function is “On,” picture is top/bottom and left/right
reversed. This function is used to project image from a ceiling
mounted projector.
Ceiling function
Rear
When this function is “On,” picture is left/right reversed. This function
is used to project image to a rear projection screen.
Rear function
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Power management
This projector is equipped with a power management function. When the input signal is interrupted and any button is not
pressed for 30 seconds or more, the power management function operates in order to reduce power consumption and
conserve lamp operating time. The factory default settings for power management are "Ready" and "5 Min".
OPERATION
1) If the input signal is interrupted and any button is not pressed for 30 seconds or more, the message "No signal" and the
timer display appears on the screen. Then the count-down starts for the time being set.
If "Ready" is selected
2) When the set time is elapsed, the lamp will be switched off
and lamp cooling starts. The READY indicator will be
switched off while the lamp cooling is in progress, and the
projector cannot be operated during this time.
Time left until Lamp off.
3) When the lamp cooling is completed, the READY indicator
starts flashing to notify the operator that power
management mode is active. In this condition, the lamp
will turn on and images will be projected if a signal starts
being input or the projector is operated.
When a SELECT button is pressed,
the adjustment screen is displayed.
If "Shut down" is selected
2) When the set time is elapsed, the lamp will be switched off
and lamp cooling starts. The READY indicator will be
switched off while the lamp cooling is in progress, and the
projector cannot be operated during this time.
3) When the lamp cooling is completed, the power switches
off.
Use the POINT LEFT/RIGHT button(s)
to select the power management
function mode ("Off", "Ready" or "Shut
down").
Press SELECT button
at this icon to display
next items.
Use the POINT DOWN button to move
the pointer to the time setting, and then
use the POINT LEFT/RIGHT button(s)
to set the time (1 minute to 30
minutes).
If "Off" is selected
The power management function is canceled.
On start
On start
When this function is “On,” projector is automatically turned on just
by switching MAIN ON/OFF SWITCH on.
Press SELECT button at this
icon to display previous items.
Note ; Be sure to turn projector off properly (refer to section
“TURNING OFF PROJECTOR” on P21). If projector is turned
off in wrong steps, On Start function does not operate
properly.
Move pointer to item and then press
POINT LEFT/RIGHT button(s).
Lamp Mode
This Projector is equipped with 2 Projection Lamps and a number of using lamps can be switched to 2 lamps or 1 lamp.
Using 1 lamp maintain life of Projection Lamps.
To change over Lamp Mode
1. Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to select SETTING and
press SELECT button. Setting dialog box appears.
2. Press POINT DOWN button to move a red frame pointer to “Lamp mode”. Set "2 lamps mode" or "1 lamp mode" by
pressing POINT LEFT/RIGHT button(s). When Lamp Mode is set from "2 lamps mode" to "1 lamp mode" image
becomes little darker. When Lamp Mode is set from "1 lamp mode" to "2 lamps mode" image become brighter
gradually.
NOTE : After changing Lamp Mode, it can not be switched again for 90 seconds.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Remote control
Remote control
This projector has eight different remote control codes; the factory-
set normal code (Code 1) and the other seven codes (Code 2 to
Code 8). This switching function prevents remote control operation
mixture (jam) when operating several projectors or video equipment
together.
For example operating projector in “Code 7,” both projector and
Remote Control Unit must be switched to “Code 7.”
To change the code of Projector;
To change the Remote control code of the projector used in ON-
SCREEN MENU is selectable from Code 1 to Code 8.
To change the code of the Remote Control Unit;
To change the remote control code of the Remote Control Unit, set
the DIP switches 1-3 inside the battery compartment box of the
Remote Control Unit. (Refer to P17.)
When pressing SELECT button
at Remote control, Remote con-
trol code Menu appears.
USB
This Projector is equipped with USB port for interactive operation
between a projector and computer. Set mode following steps below.
USB
Wireless Mouse mode
Select "
" when controlling a computer with Remote Control of
this projector.
Projector mode
"
" Not used.
Move a pointer to item and then
press POINT LEFT/RIGHT
button(s).
Key lock
Key lock
This function locks the operation of the projector's control panel and
the remote control.
This cancels the Key lock function.
This locks operation of the projector's control panel.
This locks operation of the remote control.
If the projector's control panel accidentally becomes locked and you
do not have the remote control nearby, disconnect the AC cord to
turn off the power, and then while pressing a SELECT button,
reinsert the AC cord, This will cancel the projector's control panel
lock.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING
Lamp counter reset
Be sure to reset Lamp Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP
REPLACE indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN
MENU will appear. Press POINT LEFT/RIGHT button(s) to
move a red frame pointer to SETTING Menu icon.
1
Press POINT DOWN button to move a red frame pointer to
2
“Lamp counter reset” and then press
SELECT button.
Move arrow to replaced lamp number (Lamp 1 or Lamp 2) and
3
then press
SELECT button. Message "Lamp replace counter
Reset?" is displayed. Move pointer to [Yes] and then press
SELECT button.
Move pointer to Lamp counter reset
and then press SELECT button.
Move arrow to replaced lamp
number (Lamp 1 or Lamp 2) and
1
2
NOTE: Be sure to reset correct lamp number otherwise LAMP
REPLACE indicator continues lighting.
then press
SELECT button.
Another confirmation dialog box appears and select [Yes] to
reset Lamp Replace Counter.
4
Do not reset Lamp Replace Counter except after Projection lamp is
replaced.
Factory default
This function returns all setting values except for the lamp counter to
the factory default settings.
1
2
Message "Lamp replace counter Reset?" is
displayed. Move pointer to [Yes] and then
press SELECT button.
Press POINT UP/DOWN button to move a red frame pointer to
“Factory default” and then press
SELECT button. The message
"Return to Factory default?" is displayed. Move the pointer to [Yes]
and then press SELECT button.
Factory default
Another confirmation dialog box appears and select [Yes]
and then
Return the projector to Factory default.
press SELECT button.
Quit
Closes SETTING MENU.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
OPERATING WIRELESS MOUSE
Wireless Remote Control Unit is not only able to operate this projector but also function as a wireless mouse for most
Personal Computers. POINT button, drag ON/OFF button and two CLICK buttons are used for wireless mouse operation.
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen.
INSTALLATION
To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of the mouse driver (not
supplied) is required. Make sure that the mouse driver is properly installed in your computer. And make sure that the mouse
port (or USB port) of a Personal Computer is activated.
Connect the mouse port (or USB port) of your computer to
Control Port (or USB connector) of this projector with Control
Cable (or USB cable). (Refer to page 13, 14 for connection.)
1
Note : When your computer has no mouse
port, connect Serial Port of your
computer to Control Port of the
projector with Control Cable for Serial
Port (supplied).
Turn the projector on first, and then turn on your computer.
When the computer is switched on first, Wireless Mouse may not
work properly.
2
Note:
The wireless mouse function by connection with a control port does
not operate in remote control code 2-8. (See page 41)
OPERATING WIRELESS MOUSE
When controlling a PC mouse pointer, operate Wireless Mouse with MOUSE POINTER, Drag ON/OFF button, LEFT CLICK
button and RIGHT CLICK button on Wireless Remote Control Unit.
DRAG ON
MOUSE POINTER
INDICATOR
Used to move PC mouse pointer. The pointer is moved
corresponding with the direction you are pressing.
LEFT CLICK button
This button has the same function as the left button in a PC mouse.
Press this button and the POINT button to drag a selected screen
object.
DRAG ON/OFF
button
RIGHT CLICK button
This button has the same function as the right button in a PC mouse.
MOUSE POINTER
(Move the pointer)
DRAG ON/OFF button
Use this button and the MOUSE POINTER to drag a selected screen
object. Press and release the Drag ON/OFF button, DRAG ON
INDICATOR lights green and the remote control is in Drag mode.
Use the POINT button in the direction that you want to drag the
screen object. Press and release the Drag ON/OFF button again or
press any other button, to drop the object at the new screen location.
LEFT CLICK button
(left button of the mouse)
RIGHT CLICK button
(right button of the mouse)
MAINTENANCE
WARNING TEMP. INDICATOR
WARNING TEMP. Indicator flashes red and projector is automatically turned off when an internal temperature of a projector
exceeds normal temperature. Wait at least 5 minutes before turning on projector again.
When WARNING TEMP. Indicator continues to flash, check items listed below.
Ventilation Slots of a projector may be blocked. In such an event, reposition a projector so that Ventilation Slots are
not obstructed.
1
Air Filter may be clogged with dust particles. Clean Air Filter by following section AIR FILTER CARE AND CLEANING
on next page.
2
If WARNING TEMP. Indicator remains on after performing above checks, Cooling Fans or Internal Circuits may be
malfunctioning. Contact service personnel from an authorized dealer or a service station.
3
43
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
AIR FILTER CARE AND CLEANING
Air Filter prevents dust from accumulating on a surface of Projection Lens and Projection Mirror. Should Air
Filter become clogged with dust particles, it will reduce Cooling Fans' effectiveness and may result in internal
heat build up and adversely affect life of projector.
Clean Air Filter following steps below:
Turn power off, and disconnect AC power cord from
an AC outlet.
1
CAUTION
Do not operate a projector with Air Filter
removed. Dust may accumulate on LCD
Panel and Mirror degrading picture quality.
Do not put small parts into Air Intake Vents.
It may result in malfunction of a projector.
Pull out 2 Air Filters and Air filter Covers from a
projector.
2
3
Clean each parts (Air Filter and Air filter Cover) with
brush or wash out dust and particles. Be sure to dry
them out.
Replace Air Filter and Air Filter Cover properly. Make
sure that they are fully inserted.
4
SIDE OF PROJECTOR
BOTTOM OF PROJECTOR
AIR FILTER
AIR FILTER
COVER
COVER
AIR FILTER
AIR FILTER
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating a projector. Usage in these
environments may cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on liquid crystal panel, lens, or optical elements inside it.
This condition may degrade quality of projected image.
When above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.
CLEANING PROJECTION LENS
Follow these steps to clean projection lens:
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch lens.
1
Lightly wipe cleaning cloth over lens.
2
3
When a projector is not in use, replace lens cap.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP MANAGEMENT
This Projector is equipped with 2 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp
Management Function. Lamp Management Function detects status of two lamps and shows status on screen or on LAMP
REPLACE indicator. This function also automatically controls Lamp Mode when any of lamps is out for end of life or
malfunctions.
LAMP STATUS
INPUT 1
1
2
30
LAMP REPLACE
INDICATOR
Lamp Replace Indicator
This LAMP REPLACE indicator lights yellow when any of Projection Lamps is nearing its end, and flashes when any of them
becomes out. Check number of lamp on Lamp Status Display and replace lamp.
Lamp Status Display
Lamp Status Display appears on screen when power switch is on or changed input position (input 1, input 2 or input 3).
This shows status of each lamp as; ON, OFF, NEAR END, or OUT. Refer to following for each status.
Yellow Lamp
Dim Lamp
Projection Lamp lights normally.
Projection Lamp is turned off.
1
2
Projection Lamp is nearing its end. When image becomes
darker or color becomes unnatural, replace lamp.
(LAMP REPLACE indicator lights yellow.)
Red Lamp
LAMP STATUS
DISPLAY
(LAMP REPLACE indicator flashes yellow.)
X Mark on Lamp
Projection lamp is defective or fails to be turned on. Restart a
projector on, and make sure lamp is on. If this mark still
appears, replace lamp corresponding with number marked X.
Lamp Mode Changeover
Lamp Management Function automatically changes combination of lighting lamp (Lamp Mode) by detecting status of lamp.
When any of 2 lamps becomes out, Lamp Mode is changed over from 2 lamps to 1 lamp. Lamp Mode can be switched to 2
lamps or 1 lamp manually. Refer to SETTING section on page 39, 40.
2
1
1
2
1
2
2 LAMP MODE
1 LAMP MODE
(Example)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
LAMP REPLACEMENT
When the life of the Projection Lamp of this projector draws to an end,
the LAMP REPLACE indicator lights yellow. If this indicator lights
yellow, replace the projection lamp with a new one promptly.
LAMP REPLACE
INDICATOR
CAUTION
Allow a projector to cool, for at least 45 minutes before
you open Lamp Cover. The inside of a projector can
become very hot.
For continued safety, replace with a lamp assembly of
the same type.
Do not drop a lamp assembly or touch a glass bulb! The
glass can shatter and may cause injury.
Follow these steps to replace lamp assembly.
Check number of lamp to be replaced on Lamp Status
Display.
SCREWS
1
2
Turn off a projector and disconnect AC Power Cord. Allow a
projector to cool for at least 45 minutes.
Loosen 3 screws on Lamp Cover and remove Lamp Cover.
(See right figure.)
3
4
5
6
7
8
LAMP
COVER
Loosen 2 screws and pull out Lamp Assembly to be replaced
by grasping handle.
LAMP 1
Replace Lamp Assembly with a new one and tighten 2 screws.
Make sure that Lamp Assembly is set properly
LAMP 2
Replace Lamp Cover and tighten 3 screws.
Connect AC Power Cord to a projector and turn projector on.
SCREWS
Reset Lamp Replacement Counter. (Refer to section "Lamp
Counter Reset" on page 42.)
Make sure which number of lamp needs to be
replaced on Lamp Status Display.
Figure shows case of replacing LAMP 2.
NOTE : Do not reset LAMP REPLACEMENT COUNTER
when lamp is not replaced.
CAUTION : DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY
RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.
NOTES ON LAMP REPLACEMENT
To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing
all 2 lamps at a time.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the
following information to the dealer.
● Model No. of your projector
● Replacement Lamp Type No.
:
:
LC-W4
POA-LMP73
(Service Parts No. 610 309 3802)
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper
handling may result in accidents, injury, or create a fire hazard.
● Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR
lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.
( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous
use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.
● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who are
familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING
PROJECTOR" on pages 12 ~ 15.
2. Check cable connection. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If a projector still does not produce an image, re-start your computer.
5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's
display.Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be
sure to turn a computer and monitor off before you power up a projector. Power equipment back on in order of : Projector
and computer.)
6. If problem still exists, check following chart.
Problem:
No power.
Try these Solutions
● Plug a projector into your AC outlet.
● Turn MAIN ON/OFF switch to ON.
● Press POWER ON/OFF switch to ON.
● Make sure READY Indicator lights.
● Wait 90 seconds after a projector is turned OFF when turning a projector back on.
NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as
follows:
1. LAMP indicator lights bright and READY indicator turns off.
2. After 90 seconds, READY indicator lights green again and a projector may be
turned on by pressing Power ON-OFF button.
● Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY
indicator flashes, a projector can not be turned on.
(See "TURNING ON/OFF PROJECTOR" section on page 21.)
● Check Projection Lamp. (Refer to page 46.)
● Adjust focus of a projector.
● Check Projection Lens to see if it needs cleaning.
Image is out of
focus.
NOTE : Moving a projector from a cool temperature location to a warm temperature location
may result in moisture condensation on Projection Lens. In such an event, leave a
projector OFF and wait until condensation disappears.
● Check Ceiling / Rear feature. (See “SETTING” section on page 39.)
Picture is Left/Right
reversed.
● Check Ceiling feature. (See “SETTING” section on page 39.)
Picture is
Top/Bottom
reversed.
● Check Display feature.(See “SETTING” section on page 39.)
Some displays are
not seen during
Operation.
● Check connection between your computer or video equipment and a projector.
● When turning a projector on, it takes about 30 seconds to display an image.
● Check system that you select is corresponding with your computer or video equipment.
● Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).
No image.
● Check audio cable connection from audio input source.
● Adjust audio source.
No sound.
● Press VOLUME (+) button.
● Press MUTE button.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Problem:
Remote Control Unit
does not work.
Try these Solutions
● Check batteries.
● Check ALL-OFF switch on Remote Control Unit is set to “ON.”.
● Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
● Make sure you are not too far from a projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m).
● Check remote control code from Remote Control Unit.
(See “SETTING” section on page 41.)
● Check cable connection between a projector and your computer.
● Check mouse setting on your computer.
● Turn a projector on before turning on a computer.
Wireless Mouse
function does not
work.
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.
You can often correct operating problems yourself. If a projector fails to work properly, see "TROUBLESHOOT-
ING" section on page 48, 49. To correct failure, try "Solutions".
If after following all operating instructions, you find that service is necessary, contact Eiki Service Station or store
where you purchased unit.
Give model number and explain difficulty. We will advise you how to obtain service.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
49
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
INDICATORS AND PROJECTOR CONDITION
Check the Indicators for projector condition.
Indicators
Projector Condition
WARNING
READY
TEMP.
green
LAMP
REPLACE
yellow
LAMP
red
red
The projector is OFF. (The MAIN SWITCH OFF POSITION OR
THE AC Power Cord is unplugged.)
The projector is READY to be turned on with the POWER ON-
OFF button.
✽
✽
The projector is operating normally.
The temperature inside the projector is abnormally high. The
projector cannot be turned on. When the projector is cooled
down enough and the temperature returns to normal, the READY
indicator lights green and the projector can be turned on. (The
WARNING TEMP. indicator keeps flashing.) Check and clean
the Air Filter.
✽
The projector is cooled down enough and the temperature
returns to normal. When turning on the projector, the WARNING
TEMP. indicator stops flashing. Check and clean the Air Filter.
✽
✽
The projector is being cooled down. It cannot be turned on until
the READY indicator lights green.
The projector detects an abnormal condition and cannot be
turned on. Unplug the AC Power Cord and plug it again to turn
on the projector. If the projector is turned off again, disconnect
the AC Power Cord and contact the dealer or the service center
for service and checkup. Do not leave the projector on. It may
cause electric shock or a fire hazard.
✽
✽
The projector is in the Power management mode.
• • • on
• • • flashing
• • • dim
• • • off
✽ When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow,
replace the projection lamp with a new one promptly. Reset the Lamp Replace Counter after replacement of the lamp.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
MENU TREE
Computer Input/Video Input
Input 1
Digital
N/A
Input
Go to System (1)
Analog
Y, Pb/Cb, Pr/Cr
RGB
Input 2
Input 3
Go to System (3)
Go to System (1)
Go to System (2)
Video
Go to System (2)
Go to System (2)
S-Video
Y, C
✽N/A - - - not applicable
Computer Input
Image Select
Standard
Real
Image 1
Image 2
Image 3
Image 4
SVGA 1
System (1)
SVGA 2
SVGA 3
MODE 1
MODE 2
Image Adjust
Contrast
Brightness
Color Temp
0 - 63
0 - 63
High
Mid
PC Adjust
Auto PC Adj.
Low
Fine sync.
Total dots
Horizontal
Vertical
0 - 31
XLow
Red
Green
0 - 63
0 - 63
Current mode
Clamp
Display area
Blue
0 - 63
0 - 15
0 - 15
Sharpness
Gamma
Noise reduction
Progressive
640 x 480
720 x 400
800 x 600
1024 x 768
1152 x 864
1280 x 1024
1366 x 768
1400 x 1050
Quit
Off/On
Off/On
Yes/No
Image 1
Image 2
Image 3
Image 4
Quit
Reset
Store
Quit
Display area - H
Display area - V
Full screen
Reset
Mode free
Store
Screen
Full
Zoom
True
Digital zoom +
Digital zoom –
On/Off
Yes/No
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Quit
Quit
51
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Video Input
Computer Input/Video Input
Setting
Language
English
German
French
System (2)
Auto
PAL
Italian
SECAM
NTSC
NTSC 4.43
PAL-M
PAL-N
Spanish
Portuguese
Dutch
Swedish
Russian
Chinese
Korean
Japanese
Quit
System (3)
Auto
1080i60
1080i50
1035i
720p
575p
480p
Keystone
Blue back
Display
Logo
On/Off
On/Off
On/Off
On/Off
On/Off
575i
480i
Ceiling
Rear
Image Select
Standard
Cinema
Image 1
Image 2
Image 3
Image 4
Power management
Off
Ready
Shut down
1-30 Min
Quit
On start
On/Off
Image Adjust
Contrast
Brightness
Color
Tint
Color Temp
0 - 63
0 - 63
0 - 63
0 - 63
High
Mid
Lamp mode
Remote control
1 Lamp/2 Lamp
Code 1
Code 2
Code 3
Code 4
Code 5
Code 6
Code 7
Code 8
Quit
Low
XLow
Red
Green
0 - 63
0 - 63
Blue
0 - 63
0 - 15
0 - 15
USB
Mouse/Projector
Sharpness
Gamma
Noise reduction
Progressive
Reset
Key lock
Off
Projector
Remote Control
Quit
Off/On
Off/On
Yes/No
Image 1
Image 2
Image 3
Image 4
Quit
Lamp counter reset
Factory default
Yes / No
Store
Yes / No
Quit
Screen
Full
Zoom
Normal
Natural wide
Computer Input/Video Input
Sound
Volume
Treble
Bass
Built-in SP.
Mute
0 - 63
0 - 63
0 - 63
On/Off
On/Off
Quit
52
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
TECHNICAL SPECIFICATIONS
Multi-media Projector
Projector Type
17.3" x 9.1" x 23.8" (439 mm x 230 mm x 605.6 mm)
46.3 lbs (21 kg)
(W x H x D)
Dimensions
Net Weight
1.21" TFT Active Matrix type, 3 panels
1366 x 768 dots
LCD Panel System
Panel Resolution
Number of Pixels
Color System
3,147,264 (1366 x 768 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 and 1080i-60
Up and Down
High Definition TV Signal
Motorized Lens Shift
Scanning Frequency
Horizontal Resolution
Projection Lamp
Input 1 Jacks
H-sync. 15 ~ 120 KHz, V-sync. 50 ~ 120 Hz
800 TV lines
250 watt type x 2
DVI-I Terminal (Digital/Analog), RCA Type (Audio R and L)
and DIN 8-pin (Control port)
BNC Type x 5 (R/Pr, G/Y, B/Pb, H/HV and V), RCA Type (Audio R and L)
and DIN 8-pin (Control port)
Input 2 Jacks
Input 3 Jacks
Other Jacks
BNC Type x 2 (VIDEO/Y, C), RCA Type (Audio R and L)
and DIN 4-pin (S-Video)
Serial port in (DB 9), Serial port out (DB 9), USB port,
Audio Monitor out (RCA Type R and L) and Wired Remote Jack
INT. SP. Stereo (R and L), 3 watt RMS (T.H.D. 10%)
0˚ to 6.9˚
Built-in Speakers
Feet Adjustment
Voltage and
AC 100 ~ 120 V (8.0 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)
AC 200 ~ 240 V (4.0 A Max. Ampere), 50 / 60 Hz (Continental Europe)
Power Consumption
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
Operating Temperature
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Storage Temperature
Power Source
Operating Range
Dimensions
Net Weight
Laser Pointer
:
:
:
:
:
AA or R06 Type x 2
16.4’ (5m) / 30˚
2.0” x 1.4” x 7.6” (50mm x 36mm x 193mm)
0.35 lbs (160 g) (including batteries)
(Max. Output : 1mW / Wave length : 650 20nm)
Class II Laser
Remote Control Transmitter
Owner’s Manual (Print and CD-ROM)
AC Power Cord
Accessories
Wireless/Wired Remote Control Transmitter and Batteries
Remote Control Cable
DVI-VGA Cable and DVI Cable
3 Types Control Cable (For PS/2, Serial and ADB port)
3 Types Light-Block Sheet (For option lens)
2 Types Lens Attachment (For option lens)
Protective Dust Cover
Real Color Manager
● Specifications are subject to change without notice.
● LCD panels are manufactured to the highest possible standards. At least 99.99% of the pixels are effective,
however a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD
panels.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
CONFIGURATIONS OF TERMINALS
DVI-I TERMINAL (DIGITAL/ANALOG)
This terminal accepts only Digital (TMDS) or Analog (RGB) output signal. Connect display output terminal of computer to this
terminal with DVI cable (supplied).
C1 Analog Red Input
C2 Analog Green Input
Pin Configuration
C3 Analog Blue Input
C1 C2
C4 Analog Horiz. sync
C5 Analog Ground (R/G/B)
1
9
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
T.M.D.S. Data2–
T.M.D.S. Data2+
9
T.M.D.S. Data1–
17 T.M.D.S. Data0–
18 T.M.D.S. Data0+
10 11 12 13 14 15 16
10 T.M.D.S. Data1+
17 18 19 20 21 22 23 24
T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield
No Connect
No Connect
DDC Clock
12 No Connect
13 No Connect
14 +5V Power
15 Ground (for +5V)
16 Hot Plug Detect
20 No Connect
21 No Connect
22 T.M.D.S. Clock Shield
23 T.M.D.S. Clock+
24 T.M.D.S. Clock–
C3 C4
C5
DDC Data
Analog Vert. sync
CONTROL PORT CONNECTOR
Terminal : Mini DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with Control Cable (supplied).
PS/2
-----
Serial
R X D
-----
ADB
-----
Pin Configuration
1
2
3
4
5
6
7
8
CLK
DATA
GND
-----
ADB
-----
-----
8
7
6
GND
RTS
GND
-----
5
4
3
2
1
-----
T X D
GND
GND
-----
GND
-----
-----
GND
SERIAL PORT IN/OUT TERMINAL
Connect serial port output terminal of computer to this terminal with Serial Cable (not supplied).
Pin Configuration
1
2
3
4
5
6
7
8
9
-----
RxD
TxD
-----
5 4 3 2 1
9 8 7 6
Ground
-----
-----
-----
-----
USB PORT TERMINAL
Pin Configuration
Connect USB port output terminal of computer or peripheral equipment to this terminal with USB port Cable (not
supplied).
1
2
3
4
Vcc
- Data
+ Data
Ground
2
3
1
4
54
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
55
Download from Www.Somanuals.com. All Manuals Search And Download.
A-key to better communications
Canada
U.S.A.
EIKI International, Inc.
30251 Esperanza
EIKI CANADA - Eiki International, Inc.
P.O. Box 156, 310 First St. - Unit 2,
Midland, ON, L4R 4K8, Canada
Tel : 800-563-3454 (705)-527-4084
Fax : 800-567-4069 (705)-527-4087
E-Mail : [email protected]
Rancho Santa Margarita
CA 92688-2132
U.S.A.
Tel : 800-242-3454 (949)-457-0200
Fax : 800-457-3454 (949)-457-7878
E-Mail : [email protected]
Eastern Europe
EIKIˆ CZECH spol. s.r.o.
Umelecká 15
170 00 Praha 7
Czech Republic
Tel : +42 02 20570024
+42 02 20571413
Fax : +42 02 20571411
E-Mail : [email protected]
Deutschland & Österreich
EIKI Deutschland GmbH
Am Frauwald 12
65510 Idstein
Deutschland
Tel : 06126-9371-0
Fax : 06126-9371-14
E-Mail : [email protected]
Japan & Worldwide
EIKI Industrial Company Limited.
4-12 Banzai-Cho, Kita-Ku, Osaka,
530-0028 Japan
Tel : +81-6-6311-9479
Fax : +81-6-6311-8486
E-Mail : [email protected]
Printed in Japan
Part No. 610 329 6937 (1AA6P1P5181-- M4RBF)
© 2006 Eiki International, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
LCD PROJECTOR
LENS REPLACEMENT AND INSTALLATION PROCEDURES
CAUTION
When installing or replacing the Projection Lens, refer to this manual. For installation of
the lens, use the parts designated in the manual. Do not use the installation manual and
Light-Block Sheets in the lens package.
Check the following parts supplied to this projector.
● LIGHT-BLOCK SHEETS 3 pcs.
● LENS ATTACHMENT (01) 1 pce.
● LENS ATTACHMENT (02) 1 pce.
● LIGHT-BLOCK SHEET MOUNTING BASE 1 pce.
● LIGHT-BLOCK SHEET MOUNTING SCREWS 2 pcs.
AVAILABLE LENS
This projector applies the Projection Lenses listed below. Use the suitable lens for where
the projector is used.
Model NO.
Type
Zoom
Focus
LNS-W01
LNS-W01Z
Fixed Short Throw Lens
Fixed
Manual
LNS-T01
LNS-T01Z
Fixed Long Throw Lens
Fixed
Manual
LNS-T02
LNS-T03
Long Throw Zoom Lens
Long Throw Zoom Lens
Motor Driven
Manual
Motor Driven
Manual
LNS-W02
LNS-W02Z
Short Throw Zoom Lens I
Short Throw Lens II
Motor Driven
Fixed
Motor Driven
Manual
LNS-W03
Semi-Long Throw
Zoom Lens
LNS-M01
LNS-M01Z
Motor Driven
Motor Driven
Motor Driven
Motor Driven
Motor Driven
Motor Driven
LNS-S01
Standard Zoom Lens I
LNS-S02
LNS-S02Z
Standard Zoom Lens II
LNS-S03
LNS-W04
LNS-W05
LNS-W06
LNS-W07
Standard Zoom Lens III
Wide Zoom Lens
Motor Driven
Motor Driven
Motor Driven
Motor Driven
Fixed
Motor Driven
Motor Driven
Motor Driven
Motor Driven
Manual
Wide Zoom Lens
Wide Zoom Lens
Fixed Short Throw Lens
E
NOTES ON LENS INSTALLATION
●
Lens installation and replacement should be made by the qualified service
personnel.
Be sure to install the lens following this procedure precisely.
Do not touch or remove any parts except the lens and related parts. It may
result in malfunctions, electrical shock, fire hazard or other accidents.
Before installing or replacing the lens, check that the Model No. of the
Projection Lens matches to the projector.
When moving or setting up the projector, be sure to replace the Lens Cover
to protect the surface. And be careful not to hold or subject the lens to
strong forces. It may damage the lens, cabinet, or mechanical parts.
For details of the lens and installation, contact the sales dealer where you
purchased the projector.
●
●
●
●
●
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
LENS REPLACEMENT AND INSTALLATION PROCEDURE
NOTE: The installation procedure and needed
parts for lens installation depend on the type of
the Projection Lens. Check the Model No. of
the Projection Lens and be sure to install or
replace the lens following the procedure below.
Remove the Lower Lens Cover. Remove the two
B
1
(2) Screws A. Push the part B and pull the Lower
Lens Cover down. (See Fig. 1.)
LOWER LENS
COVER
A
Fig-1
C
Remove the four (4) Screws C. Pull the Upper
Lens Cover toward the front and remove.
(See Fig. 2.)
2
3
UPPER LENS
COVER
Fig-2
C
E
UPPER LENS
COVER
Remove the two (2) Screws D and the Cover
Plate on the back of the Upper Lens Cover.
(See Fig. 3.)
COVER PLATE
D
Fig-3
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Replace the Lens Cap on the rear (mounting side) of the Projection Lens and mount a lens on
the Lens Attachment with four (4) Screws. (Use the screws attached on the lens.)
Connect the Lens Motor Lead connector to the socket on the right-top of the Lens Attachment
(Motor Driven Lens only). See Fig. 5.
4
When installing the LNS-W01, LNS-W01Z, LNS-T01, LNS-T01Z, be sure to mount the lens and
the Light-Block Sheet Mounting Base on the Lens Mounting Bracket. (See Fig. 8)
LENS ATTACHMENT
LENS LOCK
LEVER
LENS LOCK SCREW
Fig-4
LIGHT-BLOCK SHEET
MOUNTING BASE
Part No. (610 303 9596)
Kit parts with two (2) screws.
DRIVER
IN THE LENS
Part No. (610 275 6029)
Lens attachments For each lens.
LENS ATTACHMENT
TYPE No. (PART No.)
Lens Model No.
LNS-W01, LNS-W01Z, LNS-W02Z,
Lens Attachment 01
POA-LNA-01
LOCATE MOTOR
ON RIGHT SIDE
LNS-W03, LNS-T01, LNS-T01Z,
LNS-T02, LNS-S02, LNS-S02Z,
LNS-S03, LNS-M01Z, LNS-W04,
LNS-W05, LNS-W06, LNS-W07
LENS
ATTACHMENT
(610 303 8742)
Lens Attachment 02
POA-LNA-02
LNS-W02, LNS-M01, LNS-S01
SOCKET
(610 304 6228)
CONNECTOR
Fig-5
LENS MOTOR LEAD
Grasp (release lock) the Lens Lock Lever and turn it fully upward. (See Fig. 6.)
Install the lens into the projector. Grasp the Lens Lock Lever and turn the Lever fully downward
until lever is Locked (clicked position) properly. (See Fig. 7.)
5
E
When installing the Motor Driven Lens, be sure to mount the Lens Motor on the right side. (See Fig. 5.)
After installing the lens, make sure the lens is not loose and properly installed.
LENS LOCK RELEASE
LENS LOCK
Grasp (unlock)
Grasp (unlock) the
the Lens Lock
Lever and pull
upward.
Lens Lock Lever and
fully pull downward
until it is locked
(clicked).
Fig-6
Fig-7
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
This projector has three Light-Block Sheets. Use the Light-Block Sheet corresponding with the lens. (Refer
to the list below.)
6
Set the Light-Block Sheet through the lens.
Make sure the shape of the Light-Block Sheets are correct and be sure to set them as shown in the Fig. 8.
NOTE:
●
Be sure to set each Light-Block Sheet as shown in Fig. 8.
●
Make sure the mark (TOP and BACK) on the Light-Block Sheets are correct and set them properly.
Light-Block Sheets for each lens.
Lens Model No.
Type No. (Part No.)
LNS-S02, LNS-S02Z, LNS-W04
TYPE FD1 (610 322 8051)
LNS-M01, LNS-T02, LNS-W02,
LNS-M01Z, LNS-W02Z, LNS-S01,
LNS-W03, LNS-W07
TYPE FE1 (610 322 7269)
LNS-W01, LNS-T01, LNS-W01Z,
LNS-T01Z, LNS-S03,
LNS-W06, LNS-W05
TYPE FF1 (610 322 7788)
Not include Light-Block Sheet
Mounting Base and screws.
For Models
LNS-W01, LNS-W01Z, LNS-T01, LNS-T01Z
LIGHT BLOCK SHEET
LIGHT BLOCK SHEET
Make sure the sheet figure is
correct and put in proper position.
Make sure the sheet figure is
correct and put in proper position.
E
Mount the Light-Block Sheet
with two (2) screws.
Fig-8
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjust the focus of the Projection Lens. (LNS-W01, LNS-W01Z, LNS-T01, LNS-T01Z, LNS-W03,
and LNS-W07 only.) Set up the projector and project an image on the screen. Loosen the Focus
Lens Lock Screw and rotate the Projection Lens to obtain a proper focus. After adjusting the focus,
be sure to lock the Projection Lens with the Focus Lens Lock Screw securely. (See Fig. 5.) Adjust
the focus of the Projection Lens MODEL LNS-W03 by following the Focus Adjustment on page 6.
7
Replace the Upper Lens Cover. Fix the Upper Lens Cover with four (4) Screws C. (See Fig.2.)
Except the Model LNS-W01, LNS-W01Z, LNS-T01, and LNS-T01Z, proceed with the following.
Slide the Light-Block Sheets into the guide of the Upper Lens Cover and set them in front of the
flap. (See Fig. 9.)
8
Replace the Lower Lens Cover. Fix the Lower Lens Cover with two (2) Screws A. (See Fig.1.)
Except the Model LNS-W01, LNS-W01Z, LNS-T01, and LNS-T01Z, proceed with the following.
Slide the Light-Block Sheets into the guide of the Lower Lens Cover and set them in front of the
flap. (See Fig.9.)
9
Turn the projector on and operate the Lens shift, Zoom, and Focus fully to check the Light-Block
Sheets. If the Light-Block Sheets interfere with those operations, check if the Light-Block Sheets
are set properly.
10
1 UPPER LENS
Slide both upper sides of LIGHT BLOCK
COVER
2
Sheets in between 1 and
.
FLAP
Slide into front
of the flap.
2
GUIDE
E
LIGHT-BLOCK
SHEETS
LOWER LENS
COVER
FLAP
Fig-9
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
FOCUS ADJUSTMENT (For Model LNS-W03 and LNS-W07)
Set up the projector and project image on the
screen.
● mark (yellow)
1. Loosen the Focus Lock Screw on the projection
lens.
2. Rotate the projection lens to obtain a proper
focus on the center area of the screen.
When the distance of the screen and lens is one
(1) meter, set the ● mark (yellow) of the lens on
the Focus Lock Screw position.
Focus Lock Ring
3. Lock the Focus Lock Screw securely.
Focus Lock Screw
When the proper focus is not observed at the outer
area of the screen, proceed with the following
adjustments.
4. Loosen the Focus Lock Ring on the projection
lens. (Turn the Lock Ring counter-clockwise.)
5. Rotate the lens to obtain a proper focus on the
outer area of the screen.
6. Lock the Focus Lock Ring securely. (Turn the
Lock Ring clockwise.)
If the proper focus is not observed over the entire
screen, repeat the above adjustments 1-6.
E
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Correcting the focus
When the lens is attached to the projector and images are being projected on the screen, the
peripheral focus may be out of focus in some localized areas. If this happens, insert the accessory
in between the lens attachment and the lens to correct the focus.
D'
Inserting the spacers corrects the distance for the best
diagonal focus at the screen.
B'
Screen
60-inch projection
The corrected distance is determined by the thickness
of the spacers that are used. As a guide, the distance
is adjusted by approximately 30 mm for each 0.1 mm
thickness of the spacers.
A'
C'
Distance
There are three types of spacers provided, and there
are four of each spacer type. Use these spacers to
correct the distance as required.
Spacer “1”
Color: Clear
Thickness: 0.1 mm
Correction distance
30 mm/for 60-inch
projection
A
C
Spacer “2”
Color: Black
Thickness: 0.2 mm
Correction distance
60 mm/for 60-inch
projection
Lens
Spacer “1”
Color: Cream
Thickness: 0.3 mm
Correction distance
90 mm/for 60-inch
projection
Lens attachment
B
D
BE SURE TO CHECK FOR SAFETY
After installing or replacing the lens, be sure to check the following for safety.
1. Check if the lens is securely fixed with the screws.
2. Check if no wiring is damaged or tangled on the gear of the lens motor
or the other mechanical parts.
3. Check if no part is missing and no mounting part is loose.
Some parts are not used for installation or replacement. Keep these parts for later use.
NOTE: Figures in this manual may differ from the actual product.
E
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
E
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|