Eiki CRT Television LC X71L User Manual

MULTIMEDIA PROJECTOR

MODEL LC-X71

LC-X71L (Lensless)

OWNER’S MANUAL

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY INSTRUCTIONS

All the safety and operating instructions should be read before

the product is operated.

This projector should be operated only from the type of power

source indicated on the marking label. If you are not sure of

the type of power supplied, consult your authorized dealer or

local power company.

Read all of the instructions given here and retain them for later

use. Unplug this projector from AC power supply before

cleaning. Do not use liquid or aerosol cleaners. Use a damp

cloth for cleaning.

Do not overload wall outlets and extension cords as this can

result in fire or electric shock. Do not allow anything to rest on

the power cord. Do not locate this projector where the cord

may be damaged by persons walking on it.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm,

or when it is left unattended and unused for long periods of

time, unplug it from the wall outlet. This will prevent damage

due to lightning and power line surges.

Do not attempt to service this projector yourself as opening or

removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service

personnel.

Unplug this projector from wall outlet and refer servicing to

qualified service personnel under the following conditions:

a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the projector.

Do not expose this unit to rain or use near water... for

example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the

manufacturer as they may cause hazards.

c. If the projector has been exposed to rain or water.

d. If the projector does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the projector to normal operation.

e. If the projector has been dropped or the cabinet has been

damaged.

f. When the projector exhibits a distinct change in

performance-this indicates a need for service.

Do not place this projector on an unstable cart, stand, or table.

The projector may fall, causing serious injury to a child or

adult, and serious damage to the projector. Use only with a

cart or stand recommended by the manufacturer, or sold with

the projector. Wall or shelf mounting should follow the

manufacturer's instructions, and should use a mounting kit

approved by the manufacturers.

An appliance and cart combination should

be moved with care. Quick stops,

excessive force, and uneven surfaces

may cause the appliance and cart

combination to overturn.

When replacement parts are required, be sure the service

technician has used replacement parts specified by the

manufacturer that have the same characteristics as the

original part. Unauthorized substitutions may result in fire,

electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask

the service technician to perform routine safety checks to

determine that the projector is in safe operating condition.

Slots and openings in the back and bottom of the cabinet are

provided for ventilation, to insure reliable operation of the

equipment and to protect it from overheating.

The openings should never be covered with cloth or other

materials, and the bottom opening should not be blocked by

placing the projector on a bed, sofa, rug, or other similar

surface. This projector should never be placed near or over a

radiator or heat register.

This projector should not be placed in a built-in installation

such as a book case unless proper ventilation is provided.

Voor de klanten in Nederland

Bij dit product zijn batterijen

geleverd.

Wanneer deze leeg zijn,

moet u ze niet weggooien

maar inleveren als KCA.

Never push objects of any kind into this projector through

cabinet slots as they may touch dangerous voltage points or

short out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the projector.

Do not install the projector near the ventilation duct of air-

conditioning equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPLIANCE

Federal Communication Commission Notice

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such

changes or modifications should be made, you could be required to stop operation of the equipment.

Model Numbers

Trade Name

: LC-X71/LC-X71L

: EIKI

Responsible party

Address

: EIKI International, Inc.

: 30251 Esperanza Rancho Santa Margarita CA 92688-2132, U.S.A.

Telephone No.

: 800-242-3454 (949-457-0200)

AC POWER CORD REQUIREMENT

The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.

AC Power Cord for the United States and Canada:

AC Power Cord used in the United States and Canada is listed by the Underwriters

Laboratories (UL) and certified by the Canadian Standard Association (CSA).

AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the

plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable

to insert the plug into the outlet, contact your electrician.

GROUND

THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

FEATURES AND DESIGN

COMPUTER INPUT

SELECTING INPUT SOURCE

SELECTING COMPUTER SYSTEM

PREPARATION

PC ADJUSTMENT

AUTO PC ADJUSTMENT

MANUAL PC ADJUSTMENT

NAME OF EACH PART OF PROJECTOR

SETTING-UP PROJECTOR

CONNECTING AC POWER CORD

POSITIONING PROJECTOR

LENS INSTALLATION

PICTURE IMAGE SELECT

IMAGE LEVEL SELECT

PICTURE SCREEN ADJUSTMENT

PICTURE SCREEN SELECT

ADJUSTABLE FEET

INSTALLING PROJECTOR IN PROPER POSITION

MOVING PROJECTOR

VIDEO INPUT

SELECTING INPUT SOURCE

SELECTING VIDEO SYSTEM

CONNECTING PROJECTOR

PICTURE IMAGE SELECT

TERMINALS OF PROJECTOR

CONNECTING TO COMPUTERS

CONNECTING TO VIDEO EQUIPMENT

IMAGE LEVEL SELECT

PICTURE SCREEN ADJUSTMENT

PICTURE SCREEN SELECT

PICTURE IMAGE

BEFORE OPERATION

PICTURE IMAGE ADJUSTMENTS

REMOTE CONTROL OPERATION

LASER POINTER FUNCTION

REMOTE CONTROL BATTERIES INSTALLATION

SETTING

TOP CONTROLS AND INDICATORS

ON-SCREEN MENU

SETTING MENU

HOW TO OPERATE ON-SCREEN MENU

FLOW OF ON-SCREEN MENU OPERATION

MENU BAR

APPENDIX

WIRELESS MOUSE

MAINTENANCE

BASIC OPERATION

WARNING TEMP. INDICATOR

AIR FILTERS CARE AND CLEANING

CLEANING PROJECTION LENS

TURNING ON/OFF PROJECTOR

TURNING ON THE PROJECTOR

TURNING OFF THE PROJECTOR

LAMP REPLACEMENT

LAMP REPLACE COUNTER

ADJUSTING SCREEN

ZOOM ADJUSTMENT

TROUBLESHOOTING

MENU TREE

FOCUS ADJUSTMENT

LENS SHIFT ADJUSTMENT

KEYSTONE ADJUSTMENT

PICTURE FREEZE FUNCTION

NO SHOW FUNCTION

P-TIMER FUNCTION

COMPATIBLE COMPUTER SPECIFICATIONS

INDICATORS AND PROJECTOR CONDITION

TECHNICAL SPECIFICATIONS

CONFIGURATIONS OF TERMINALS

OPTIONAL PARTS

LENS REPLACEMENT

PJ LINK NOTICE

PIN CODE NUMBER MEMO

DIMENSIONS

SOUND ADJUSTMENT

TRADEMARKS

● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.

● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.

● Windows and PowerPoint are registered trademarks of Microsoft Corporation.

● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation.

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES AND DESIGN

This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This

projector utilizes built-in multimedia features, a palette of 1.07 billion colors, and matrix liquid crystal display (LCD)

technology.

◆ Compact Design

◆ Digital Zoom (for Computer)

This projector is extremely compact in size and weight.

It is designed to carry and work anywhere you wish to

use.

Digital Zoom function adjusts image size to approx. 1/4 ~

49 times of an original image size, allowing you to focus

on a crucial information at the presentation.

◆ Compatibility

◆ Keystone Correction

This projector widely accepts various video and

computer input signals such as:

Positioning of the projector may result in distorted image

being displayed in a trapezoid shape. Keystone function

solves this problem by digitally altering the projection to

produce undistorted images.

● Computers

IBM-compatible or Macintosh computer up to 1600

x 1200 resolution.

◆ Power Management

● 6 Color Systems

Power management function is provided to reduce power

consumption when the projector is not in use.

NTSC, PAL, SECAM, NTSC 4.43, PAL-M, or PAL-

N color system can be connected.

The Power management function operates to turn the

projection lamp off when the projector detects a signal

interruption or when no button is pressed for a certain

period. The projection lamp is automatically turned on

again when the projector detects a signal or any

operation button is pressed.

● Component Video

Component video signal, such as a DVD player

output high definition TV signals including 480i,

480p, 575i, 575p, 720p, 1035i, or 1080i, can be

connected.

● S-Video

This projector is shipped with this function ON.

S-Video signal, such as a S-VHS VCR output

signal, can be connected.

◆ Digital Visual Interface

◆ High Resolution Image

This projector is equipped with the DVI 24-pin terminal

for connecting DVI output from a computer.

This projector provides 1024 x 768 dots resolution for

computer input and 800 horizontal TV lines. Resolution

from a computer between XGA (1024 x 768) and UXGA

(1600 x 1200) is compressed into 1024 x 768 dots. This

projector cannot display image of over 1600 x 1200 dots.

When resolution of your computer is over 1600 x 1200,

lower the resolution for a computer output.

◆ Laser Pointer Function

Remote control supplied with this projector includes the

Laser Pointer function. This function helps you to make a

smart presentation on a projected screen.

◆ Wireless Mouse

◆ Multi-Scan System

Remote control supplied with this projector has the

Wireless Mouse function for a connected computer. This

function enables you to operate both projector and

computer with the remote control only.

This projector has the Multi-Scan System to conform to

almost all computer output signals quickly. There is no

need for a troublesome manual adjustment of frequency

and other settings.

◆ Multilanguage Menu Display

◆ One-Touch Auto PC Adjustment

Operation menu is available in 12 languages: English,

German, French, Italian, Spanish, Portuguese, Dutch,

Swedish, Russian, Chinese, Korean, or Japanese.

Incoming computer video signals are recognized and

best adjustment is automatically set by the Auto PC

Adjustment function. No complicated setup is necessary

and the projection is always precise.

◆ Pj-to NetDirector (Optional)

Pj-to NetDirector enables the projector to display the

image of the computer screen and the image data stored

in the computer via a network. The projector can also be

controlled and maintained through a web browser.

◆ Motor-driven Lens Shift

Projection lens can be moved up and down with the

motor-driven lens shift function. This function makes it

easy to provide projected image where you want.

Zoom and focus can also be adjusted with a motor-

driven operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

NAME OF EACH PART OF PROJECTOR

SPEAKERS

TOP CONTROLS

AND INDICATORS

FRONT OF CABINET

PROJECTION LENS

✽ Optional: LC-X71L

CAUTION

Do not turn on the projector with

the lens cap attached. High

temperature from light beam

may damage the lens cap and

result in fire hazard.

AIR INTAKE

VENT

LENS CAP

INFRARED

REMOTE RECEIVER

✽ Optional: LC-X71L

BACK OF CABINET

POWER CORD

CONNECTOR

TERMINALS

AND CONNECTORS

INFRARED

REMOTE RECEIVER

EXHAUST VENT

HOT AIR EXHAUSTED !

Air blown from the exhaust vent is hot.

When using or installing the projector, the

following precautions should be taken.

● Do not put a flammable object near this vent.

● Keep the rear grills at least 3.3’ (1 m) away

from any object, especially from heat-

sensitive objects.

● Do not touch this area, especially screws

and metallic parts. This area will become hot

when the projector is in use.

CARRYING

HANDLE

LAMP COVER

This projector detects internal temperature

and automatically controls operating power

of the cooling fans.

When attaching the Pj-to NetDirector

(optional) to the projector, remove these

parts. Refer to the owner’s manual of the

optional Pj-to NetDirector.

BOTTOM OF CABINET

AIR INTAKE VENTS

This projector is equipped with the cooling fans for protecting from

overheating. Pay attention to the following matters to ensure

proper ventilation and avoid a possible risk of fire and malfunction.

● Do not cover the vent slots.

● Keep this side clear of any objects. Obstructions may block

cooling air.

ADJUSTABLE FEET

AND

FEET LOCK LATCHES

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

SETTING-UP PROJECTOR

CONNECTING AC POWER CORD

This projector uses nominal input voltages of 100-120 V or 200-

240 V AC and it automatically selects correct input voltage. It is

designed to work with single-phase power systems having a

grounded neutral conductor. To reduce risk of electrical shock, do

not plug into any other type of power system.

If you are not sure of the type of power being supplied, consult

your authorized dealer or service station.

Connect the projector with all peripheral equipment before turning

it on. (See pages 12-14 for connection.)

CAUTION

For safety, unplug the AC power cord when the projector is not

in use. When the projector is connected to an outlet with AC

power cord, an appliance is in stand-by mode and consumes a

little electric power.

Connect AC power cord (supplied) to the

projector.

The AC outlet must be near this equipment and

must be easily accessible.

NOTE ON POWER CORD

AC power cord must meet the requirements of the country where you use the projector.

Confirm the AC plug type with the chart below and a proper AC power cord must be used.

If the supplied AC power cord does not match your AC outlet, contact your sales dealer.

Projector side

AC Outlet side

For the U.S.A. and Canada

For Continental Europe

Ground

To POWER CORD

CONNECTOR on your

projector.

To the AC Outlet.

(120 V AC)

To the AC Outlet.

(200 - 240 V AC)

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

POSITIONING PROJECTOR

NOTE: The figures below are only for the Model LC-X71.

A ROOM LIGHT

The projection lens is not provided with the Model LC-X71L.

Brightness in a room has a great

influence on the picture quality. It is

recommended to limit ambient lighting

in order to provide the best image.

● This projector is designed to project on a flat projection surface.

● Projector can be focused from 4.6’ (1.4 m) ~ 48.3’ (14.7 m).

● Refer to the figure below to adjust the screen size.

47.3’(14.4m)

35.4’(10.8m)

400”

Max. Zoom

23.6’(7.2m)

11.8’(3.6m)

300”

231”

308”

200”

4.6’(1.4m)

Min. Zoom

100”

77”

154”

40”

31”

Max. Zoom

Min. Zoom

40”

31”

100”

77”

150”

115”

200”

154”

250”

192”

300”

231”

400”

308”

Screen

Size

4.6’ (1.4 m)

11.8’ (3.6 m) 17.7’ (5.4 m)

23.6’ (7.2m)

29.5’ (9.0 m) 35.4’ (10.8 m) 47.3’ (14.4 m)

Distance

LENS SHIFT ADJUSTMENT

Projection lens can be moved up and down with the motor-driven Lens shift function. This function makes it easy

to provide projected image where you want. The U/D ratio can be adjusted 10:0 ~ 1:1 (see Figure below). See

page 22 for operation.

Highest (10 : 0)

Lowest (1 : 1)

LENS INSTALLATION

Before setting up the projector, install a projection lens on

the projector.

1. Before installation, check the area where the projector is

used and prepare a suitable lens. For the specifications of

a projection lens, contact sales dealer where you

purchased the projector.

COVER CAP

2. For installation, refer to the installation manual of the

optional lens.

NOTE:

• When installing the lens, remove the cover cap of the projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

ADJUSTABLE FEET

Projection angle can be adjusted up to 10.5 degrees with the

ADJUSTABLE FEET.

Lift the front of the projector and pull the FEET LOCK

LATCHES in each side of the projector.

Release the FEET LOCK LATCHES to lock the

ADJUSTABLE FEET and rotate the ADJUSTABLE FEET to a

proper height, and tilt.

To retract the ADJUSTABLE FEET, lift the front of the

projector and pull and undo the FEET LOCK LATCHES.

Keystone distortion of the projected image can be adjusted by

the Menu Operation. (See pages 22 and 38.)

ADJUSTABLE FEET

FEET LOCK

LATCHES

INSTALLING PROJECTOR IN PROPER POSITION

Install the projector properly. Improper installation may reduce the lamp life and cause a fire hazard.

10˚

Do not tilt the projector more than 10 degrees from side to side.

10˚

Do not put the projector on either side to project an image.

NO SIDEWAYS

Download from Www.Somanuals.com. All Manuals Search And Download.

PREPARATION

MOVING PROJECTOR

Use the Carrying Handle when moving the projector.

Replace the lens cap and retract the ADJUSTABLE FEET

when moving the projector to prevent damages to the lens

and cabinet.

When this projector is not in use for an extended period, put

it into a suitable case (not supplied with this projector).

CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR

● Do not drop or bump the projector, otherwise damages or malfunctions may result.

● When carrying the projector, use a suitable carrying case.

● Do not transport the projector by courier or any other transport service in an unsuitable transport case.

This may cause damage to the projector. To transport the projector by courier or any other transport

service, consult your dealer for the best way.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING PROJECTOR

TERMINALS OF PROJECTOR

This projector has input and output terminals on its back for connecting computers and video equipment. Refer

to the figures on pages 12 to 14 and connect properly.

COMPUTER INPUT/MONITOR

OUTPUT TERMINAL (ANALOG)

COMPUTER INPUT

TERMINAL (DIGITAL)

COMPUTER AUDIO

INPUT 2 JACK

COMPUTER AUDIO INPUT 1/

AUDIO MONITOR OUTPUT

JACK

This terminal is switchable and

can be used as Computer Input

or Monitor Output. Set up the

terminal as either Computer Input

or Monitor Output properly before

using this terminal.

(See pages 13-14 and 24.)

Note: This terminal outputs from the 5

BNC type computer input on INPUT 2

jacks only.

Connect a computer output Connect an audio

(Digital DVI-D type) to this output (stereo) from a

terminal.

The HD (HDCP Compatible) (See page 13.)

signal can also be connected.

(See page 13.)

This terminal is switchable and

can be used as Computer

Audio Input 1 or Audio Monitor

Output (variable).

Set up the terminal as either

Computer Audio Input 1 or

Audio Monitor Output properly

before using this terminal.

(See pages 13 and 24.)

computer to this jack.

R/C JACK

When using the Wired/

Wireless remote control as

wired, connect the Wired

remote control to this jack with

USB CONNECTOR (Series B)

When controlling a computer

with the remote control of this

projector, connect USB terminal

of your personal computer to

this terminal. (See page 13.)

remote control cable

(optional).

CONTROL PORT CONNECTOR

When controlling a computer

with the remote control of this

projector, connect the mouse

port of your personal computer

to this connector. (See page

13.)

RESET BUTTON

This projector uses

micro

processor to control the unit, and

only occasionally, this micro

processor may malfunction and

need to be reset. This can be done

by pressing the RESET button with

a pen, which will shut down and

restart the unit. Do not use the

RESET function excessively.

VIDEO INPUT JACKS

AUDIO INPUT JACKS

S-VIDEO INPUT JACK

Connect composite video Connect an audio output Connect S-VIDEO

output from video equipment from video equipment to output from video

to VIDEO/Y jack or connect these jacks. (See page equipment to this

5 BNC INPUT JACKS

Connect component video

output (Y, Cb, Cr or Y, Pb, Pr)

from video equipment to

VIDEO/Y, Cb/Pb and Cr/Pr

jacks or connect computer

output {5 BNC Type (Green,

Blue, Red, Horiz. Sync, and

Vert. Sync.)} from computer to

G, B, R, H/V, and V jacks.

(See pages 13 and 14.)

component video outputs to 14.)

VIDEO/Y, Cb/Pb and Cr/Pr

jacks. (See page 14.)

jack. (See page 14.)

EXTERNAL SPEAKER TERMINALS

Connect external speakers to

these terminals. (See pages 13

and 14.)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING PROJECTOR

CONNECTING TO COMPUTERS

Cables used for connection (✽ = Cables or adapters not supplied with this projector.)

• VGA Cable (HDB 15 pin)

• DVI-Digital Cable (for Single Link T.M.D.S.) ✽

• BNC Cable ✽

• Control Cable for PS2 Port ✽, or ADB Port ✽

• USB Cable

• Audio Cables (Mini Plug (stereo) x 2) ✽

• Control Cable for Serial Port

IBM-compatible computer or Macintosh computer (VGA/SVGA/XGA/SXGA/SXGA+/WXGA/UXGA )

Desktop type

Laptop type

Monitor Output

Monitor Output USB port

Audio Output Serial port

PS/2 port

ADB port

Monitor Input

Control Cable

for Serial Port

Control Cable Control Cable

for PS/2 Port ✽ for ADB Port ✽

USB

Cable

Audio

Cable ✽

(stereo)

DVI

Cable ✽

VGA Cable

Terminal

BNC

Cable ✽

COMPUTER

AUDIO IN 1 or 2

Use one of these Control

Cables corresponding with

terminal of your computer.

USB

COMPUTER IN ANALOG

COMPUTER IN DIGITAL

CONTROL

PORT

INPUT 1

DIGITAL(DVI-D)

ANALOG IN/OUT

R/C JACK

CONTROL PORT

RESET

USB

AUDIO 1

IN/OUT

AUDIO 2

NOTE:

This terminal is switchable.

Set up the terminal as either

Computer input or Monitor

output before using this

terminal.(See page 24.)

AUDIO OUT

H/V

External Speaker Terminals

(Front of the projector)

VIDEO/Y Cb/Pb

Cr/Pr

INPUT 2

S–VIDEO

VIDEO/Y Cb/Pb Cr/Pr

R–AUDIO–L

NOTE:

This terminal is switchable.

Set up the terminal as

either Computer Audio

Input 1 or Audio Monitor

Output (variable) before

using this terminal. (See

page 24.)

Audio Cable

(stereo) ✽

(

)

MONO

INPUT 3

Terminals

of the Projector

Audio Input

External Audio Equipment

NOTE:

Audio Speakers

(stereo)

Unplug the power cords of both the projector and

external equipment from the AC outlet before

connecting cables. Turn a projector and peripheral

equipment on before computer is switched on.

Audio Amplifier

Audio Speakers

(stereo)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING PROJECTOR

CONNECTING TO VIDEO EQUIPMENT

Cables used for connection (✽ = Cables not supplied with this projector.)

• Video Cable (RCA x 1 or RCA x 3) ✽

• BNC Cable ✽

• Audio Cable {Mini Plug (stereo)} ✽

• Scart Cable ✽

• S-VIDEO Cable ✽

• Audio Cable (RCA x 2) ✽

Video Source (Example)

Video Cassette Recorder

Component video output equipment.

(such as DVD players or high-definition TV sources.)

Video Disc Player

Component Video

Output

(Y, Cb/Pb, Cr/Pr)

Component Video

Output

(Y, Cb/Pb, Cr/Pr)

RGB Scart

21-pin Output Video Output

Composite

Video Output

S-VIDEO

Output

Audio Output Audio Output

Video Cables

(RCA x 1 or

RCA x 3) ✽

Scart Cable ✽

Audio

Audio Cable

S-VIDEO

Cable ✽

(stereo)

(RCA x 2) ✽

Cable ✽

BNC Cable ✽

Y - Cb/Pb - Cr/Pr

VIDEO

AUDIO IN

S-VIDEO

COMPUTER IN ANALOG

AUDIO OUT

Audio Cable

(stereo) ✽

External Speaker Terminals

(Front of the projector)

NOTE:

This terminal is switchable.

Set up the terminal as either

Computer input or Monitor

output before using this

terminal.(See page 24.)

Terminals

of the Projector

Audio Input

External Audio Equipment

Audio Speakers

(stereo)

Audio Amplifier

NOTE:

Unplug the power cords of both the projector

and external equipment from the AC outlet

before connecting cables.

Audio Speakers (stereo)

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE OPERATION

REMOTE CONTROL OPERATION

LASER POINTER

(DRAG ON) INDICATOR

Left Side

POWER ON-OFF BUTTON

Used to turn the projector on

or off. (p.20, 21)

Lights red while the laser

beam is emitted from the

Laser Light Window.

AUTO PC ON-OFF

Lights green when dragged

to the “ON” position. (p.45)

D.ZOOM FREEZE NO SHOW

AUTO PC ADJ. BUTTON

MUTE

Use to operate the AUTO PC

Adjustment function. (p.26)

IMAGE

MUTE BUTTON

Used to mute the sound.

(p.23)

VOLUME

VOLUME+

SELECT

IMAGE BUTTON

Used to select the image

level. (p.29, 33)

KEYSTONE

DRAG ON/OFF BUTTON

Used to select the DRAG

ON/OFF position. (p.45)

ALL OFF SWITCH

When using the remote control, turn

this switch to “ON.” And turn it to

“ALL OFF” when it is not in use.

KEYSTONE BUTTON

Used to correct keystone

distortion. (p.22, 38)

LEFT CLICK BUTTON

INSIDE THE BATTERY

COMPARTMENT BOX

Used as a PC mouse in

Wireless Mouse Operation.

Press this button and the

mouse pointer button to drag

the selected screen object.

(p.45)

MOUSE POINTER

Used as a PC mouse in

Wireless Mouse Operation.

(p.45)

This Remote Control provides the DIP

switches into the battery compartment

box.

Slide the SW4 (LASER ON/OFF

switch) to the “OFF” position. The

Laser Pointer function is not operated.

Set the Switches 1-3 as shown in table

below depending on the Code No. that

you want to select as the remote

control code. (See page 41.)

LASER

RIGHT CLICK BUTTON

LASER BUTTON

Used as a PC mouse in

Wireless Mouse Operation.

(p.45)

P-TIMER INPUT 1

Used to operate the Laser

Pointer function. The laser

beam is emitted when

pressing this button for one

minute.

When using the Laser Pointer

for more than one minute,

release this button and press

it again.

ZOOM COLOR.M INPUT 2

INPUT 3

LENS SHIFT BUTTON

Used to select the Lens Shift

function. (p.22)

FOCUS LENS

DIP SWITCH SETTING

SW4 ........ LASER ON/OFF

SW1 SW2 SW3 Code No.

WIRED REMOTE JACK

OFF ON

Code 1

Code 2

Code 3

When using as

Wired

OFF

Remote Control, connect a

remote control cable (optional)

to this jack.

FOCUS BUTTON

Used to adjust focus. (p.22)

OFF OFF

Code 4

Code 5

Code 6

Code 7

Code 8

OFF ON

OFF

Battery installation is required

OFF OFF ON

OFF OFF OFF

when using as

Remote Control.

Wired

LASER POINTER FUNCTION

This remote control emits laser beam from the Laser Light Window when used as a Laser Pointer. When the

LASER button is pressed, the laser light goes on. When the LASER button is being pressed for more than one

minute or when it is released, the light goes off. The LASER POINTER INDICATOR lights RED and the LASER

is emitted with RED light to indicate the laser beam is being emitted.

The Laser emitted is the Cass II laser. Do not look into the Laser Light Window or shine laser beam onto yourself

or other people. The three marks shown below are caution labels for the laser beam.

CAUTION: Use of controls, adjustments, or performance of procedures other than those specified herein may

result in hazardous radiation exposure.

These caution labels are put on the remote control.

LASER POINTER INDICATOR

LASER LIGHT WINDOW

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE OPERATION

D.ZOOM BUTTON

Operating Range

Used to select the

DIGITAL ZOOM +/– mode

and resize the image.

(p.30)

Point the remote control toward

the projector (a Receiver

Window) when pressing any

button. Maximum operating

range for the remote control is

about 16.4’ (5 m) and 60° in front

and rear of the projector.

NO SHOW BUTTON

Used to turn the picture

into a black image. (p.23)

AUTO PC ON-OFF

D.ZOOM FREEZE NO SHOW

SELECT BUTTON

MUTE

IMAGE

FREEZE BUTTON

Used to freeze the picture.

(p.23)

Used to execute the

selected item, or expand/

compress the image in the

DIGITAL ZOOM +/- mode.

(p.30)

VOLUME

VOLUME+

SELECT

KEYSTONE

POINT (VOLUME +/-)

BUTTONS

Used to select an item or

adjust a value in On-Screen

Menu. They are also used to

pan the image in the

DIGITAL ZOOM +/- mode.

(p.30)

60°

MENU BUTTON

Used to select the MENU

Operation. (p.18, 19)

The POINT LEFT/RIGHT

buttons are also used as

VOLUME +/- buttons. (p.23)

16.4’

(5 m)

P-TIMER BUTTON

Used to operate the P-

TIMER function. (p.23)

INPUT 1 BUTTON

Used to select an input

source (INPUT 1). (p.24)

LASER

P-TIMER INPUT 1

ZOOM COLOR.M INPUT 2

INPUT 3

INPUT 2 BUTTON

ZOOM BUTTON

Used to adjust zoom.

(p.22)

Used to select an input

source (INPUT 2).

(p.25, 31)

FOCUS LENS

16.4’

(5 m)

INPUT 3 BUTTON

Used to select an input

source (INPUT 3). (p.31)

COLOR MANAGEMENT

BUTTON

Used to operate the Color

management function.

(p.35-36)

60°

REMOTE CONTROL BATTERIES INSTALLATION

Open the battery

compartment lid.

Install new batteries into

the compartment.

Replace the compartment lid.

Two AA size batteries

Press the lid downward

and slide it.

For correct polarity (+ and

–), be sure battery terminals

are in contact with pins in

the compartment.

To insure safe operation, please observe following precautions:

● Use two (2) AA or LR6 type alkaline batteries.

● Always replace batteries in sets.

● Do not use a new battery with an used battery.

● Avoid contact with water or liquid.

● Do not expose the remote control to moisture, or heat.

● Do not drop the remote control.

● If a battery has leaked on the remote control, carefully wipe the case clean and install new batteries.

● Danger of explosion if battery is incorrectly replaced.

● Dispose of used batteries according to batteries manufacturers instructions and local rules.

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE OPERATION

TOP CONTROLS AND INDICATORS

This projector has CONTROL BUTTONS (TOP CONTROLS) and INDICATORS on its top.

TOP CONTROLS AND

INDICATORS

EXT. SP SWITCH

Used to select speakers.

(Internal or External)

MENU BUTTON

SELECT BUTTON

POWER ON–OFF BUTTON

INPUT BUTTON

Used to open or

close the On-Screen

Menu. (p.18, 19)

Used to execute the

selected item. It is also

used to expand/compress

the image in the DIGITAL

ZOOM mode. (p.30)

Used to turn the projector Used to select an input

on or off. (p.20, 21)

source. (p.24, 31)

ZOOM BUTTON

AUTO PC ADJ. BUTTON

Used to adjust zoom.

(p.22)

Used to operate the Auto

PC Adjustment function.

(p.26)

FOCUS BUTTON

Used to adjust focus.

(p.22)

IMAGE BUTTON

Used to select the

image level. (p.29, 33)

LENS SHIFT BUTTON

Used to select the Lens

Shift function. (p.22)

KEYSTONE BUTTON

Used to correct

keystone distortion.

(p.21, 37)

LAMP REPLACE INDICATOR

Turns to yellow when the

projection lamp reaches its

end of life.

Blinks yellow when the

lamp cannot light up. (p.48,

55-56)

LAMP INDICATOR

Becomes dim when the

projector is turned on.

And it becomes bright

when the projector is in

stand-by mode. (p.20,

21, 55-56)

READY INDICATOR

POINT (VOLUME + / – ) BUTTONS

WARNING TEMP. INDICATOR

Lights green when the

projector is ready to be

turned on. And it blinks

green in the Power

management mode.

Used to select an item or adjust a Blinks red when the internal

value in On-Screen Menu. They are temperature of the projector

also used to pan the image in the is too high. (p.46, 55-56)

DIGITAL ZOOM +/– mode. (p.30)

The POINT LEFT/RIGHT buttons are

also used as VOLUME +/– buttons.

(p.40, 46, 55-56)

(p.23)

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE OPERATION

ON-SCREEN MENU

HOW TO OPERATE ON-SCREEN MENU

REMOTE CONTROL

You can control and adjust this projector with the On-

Screen Menu. Refer to the relevant pages to operate

each adjustment.

AUTO PC ON-OFF

1. DISPLAY MENU

POINT BUTTONS

D.ZOOM FREEZE NO SHOW

Press the MENU button to display the On-Screen Menu.

Used to move the

Pointer UP/DOWN/

RIGHT/LEFT.

MUTE

IMAGE

2. MOVING POINTER

VOLUME

VOLUME+

SELECT

Move the pointer (✽ see below) or adjust a value of an item by

pressing the POINT buttons on the top control or on the remote

control.

KEYSTONE

✽ The Pointer is an icon in the On-Screen Menu for selecting

an item. See figures in “FLOW OF ON-SCREEN MENU

OPERATION” below.

MENU BUTTON

SELECT BUTTON

Used to select the item.

TOP CONTROL

3. SELECT ITEMS

Select an item or set the selected function by pressing the

SELECT button.

POINT BUTTONS

Used to move the

Pointer UP/ DOWN/

RIGHT/ LEFT.

MENU BUTTON

SELECT BUTTON

Used to select the item.

FLOW OF ON-SCREEN MENU OPERATION

MENU BAR

MENU ICON

Display ON-SCREEN MENU

Press the MENU button to display the On-Screen Menu

(a MENU BAR). A red frame is a POINTER.

POINTER

(red frame)

Select Menu to be adjusted

POINTER (red frame)

Press the POINT UP/DOWN

buttons to move the POINTER.

Move the POINTER (red frame) to a MENU ICON that

you want to select by pressing the POINT RIGHT/LEFT

buttons.

ITEM

Control or adjust items through ON-SCREEN MENU

SELECT

BUTTON

Press the POINT UP/DOWN buttons and move the

POINTER (red frame or red arrow) to an ITEM that you

want to adjust, and then press the SELECT button to

show the ITEM DATA.

Adjust the ITEM DATA by pressing the POINT

RIGHT/LEFT buttons.

Refer to the relevant pages for details of respective

adjustments.

ITEM DATA

Press the POINT LEFT/RIGHT

buttons to adjust a value or set a

function.

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE OPERATION

MENU BAR

FOR PC SOURCE

GUIDE WINDOW

Press the MENU button when connecting to the PC input source.

IMAGE SELECT MENU

SCREEN MENU

SETTING MENU

PC SYSTEM MENU

Used to select an

image level among

Standard, Real, and

Image 1 ~ 10.

Used to adjust the

size of an image.

[Normal/True/Wide/ or reset the Lamp

Full/Digital zoom replacement counter.

+/–] (See page 30.) (See pages 38-44.)

Used to change

settings of the projector

Used to select a

computer system.

(See pages 24

and 25.)

Shows the

selected item of

On-Screen Menu.

(See page 29.)

SOUND MENU

PC ADJUST MENU

IMAGE ADJUST MENU

INPUT MENU

Used to adjust

the volume or

mute the sound.

(See page 23.)

Used to adjust

the parameters

to match with the

input signal

format. (See

pages 26-28.)

Used to adjust the computer

image. [Contrast/

Used to select an

input source (Input 1,

Input 2, or Input 3).

(See page 24.)

Brightness/Color/Tint/Color

management/Auto picture

control/Color temp./White

balance (R/G/B)/Sharpness/

Gamma/Noise reduction/

Progressive] (See pages

35-37.)

FOR VIDEO SOURCE

Press the MENU button when connecting to the VIDEO input source.

INPUT MENU

IMAGE SELECT MENU

Used to select an

input source

(Input 1, Input 2,

or Input 3). (See

page 31.)

Used to select an

image level among

Standard, Cinema,

and Image 1 ~ 10.

(See page 33.)

SCREEN MENU

Used to adjust the size

of image to Normal or

Wide. (See page 34.)

AV SYSTEM MENU

IMAGE ADJUST MENU

Same function as

menu for PC source.

Same function as

menu for PC source.

Used to select the

system of selected

video source. (See

page 32.)

Used to adjust the picture

image. [Contrast/Brightness/

Color/Tint/Color management/

Auto picture control/Color

temp./White balance (R/G/B)/

Sharpness/Gamma/Noise

reduction/Progressive] (See

pages 35-37.)

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC OPERATION

TURNING ON / OFF PROJECTOR

TURNING ON THE PROJECTOR

Complete peripheral connections (with a computer, VCR, etc.)

before turning on the projector.

Connect the projector’s AC power cord into an AC outlet. The

LAMP indicator lights RED, and the READY indicator lights

GREEN.

Press the POWER ON-OFF button on the top control or on

the remote control. The LAMP indicator dims, and the cooling

fans start to operate. The preparation display appears on the

screen and the countdown starts.

The preparation display disappears after 30 seconds.

Selected Input Source and Lamp control

After the countdown, the input source that was selected the

last time and the Lamp control status icon (see page 41)

appear on the screen.

Lamp control status

If the projector is locked with a PIN code, a PIN code Input

Dialog Box appears. Enter a PIN code as instructed below.

PIN code Input Dialog Box

To Enter a PIN code

Select a number by pressing the POINT LEFT/RIGHT button and

fix the number with the SELECT button. The number changes to

“✳.” If you fixed a wrong number, move the pointer to “Set” or

“Clear” once by pressing the POINT DOWN button, then return to

“PIN code.” Enter the correct number.

Pointer

Repeat this step to complete entering a four-digit number.

When the four-digit number is fixed, the pointer automatically

moves to “Set.” Press the SELECT button so that you can start to

operate the projector.

If you entered a wrong PIN code, “PIN code” and the number

(✳✳✳✳) turn red and disappear. Enter a PIN code all over again.

After the OK icon

disappears, you can

operate the projector.

What is PIN code?

PIN (Personal Identification Number) code is a security code that

allows the person who knows it to operate the projector. Setting a

PIN code prevents unauthorized use of the projector.

A PIN code consists of a four-digit number. Refer to the PIN code

lock function in SETTING Menu on page 43 for locking operation

of the projector with your PIN code.

CAUTION ON HANDLING PIN CODE

If you forget your PIN code, the projector can no

longer be started. Take special care in setting a new

PIN code; write down the number in a column on

page 60 of this manual and keep it at hand. Should

the PIN code be missing or forgotten, consult your

dealer or service center.

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC OPERATION

TURNING OFF THE PROJECTOR

Press the POWER ON-OFF button on the top control or on

the remote control, and “Power off?” appears on the screen.

Press the POWER ON-OFF button again to turn off the

projector. The LAMP Indicator lights bright and the READY

Indicator turns off. After the projector is turned off, the cooling

fans operate (for 90 seconds). During this “cooling down”

period, the projector cannot be turned on.

“Power off?” disappears after 4 seconds.

When the projector has cooled down, the READY Indicator

lights GREEN again and you can turn projector on. After

cooling down completely, unplug the AC power cord.

TO MAINTAIN THE LIFE OF LAMP, ONCE YOU

TURN THE PROJECTOR ON, WAIT AT LEAST FIVE

MINUTES BEFORE TURNING IT OFF.

DO NOT UNPLUG THE AC POWER CORD WHILE

COOLING FANS ARE RUNNING OR BEFORE THE

READY INDICATOR LIGHTS GREEN AGAIN.

OTHERWISE IT WILL RESULT IN SHORTENING THE

LAMP LIFE.

Note:

• The projector cannot be turned on during the cooling period with the READY

indicator turned off. You can turn it on again after the READY indicator becomes

GREEN again.

• When the On start function is “On,” this projector is turned on automatically by

connecting the AC power cord to an AC outlet. (See page 41 for the On start

function.)

• Continuous use may result in shortening the lamp life. Turn off the projector

and rest it for about an hour in every 24 hours.

• The running speed of cooling fans is changed according to the temperature

inside the projector.

• If the WARNING TEMP indicator blinks RED, see “WARNING TEMP

INDICATOR” on page 46.

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC OPERATION

ADJUSTING SCREEN

ZOOM ADJUSTMENT

Press the ZOOM button on the top control or ZOOM ▲/▼

buttons on the remote control. “Zoom” appears on the screen.

Press the ZOOM ▲ button or POINT UP button to make the

image larger, and press the ZOOM ▼ button or POINT DOWN

button to make the image smaller.

“Zoom” disappears after 4 seconds.

FOCUS ADJUSTMENT

Press the FOCUS button on the top control or FOCUS ▲/▼

buttons on the remote control. “Focus” appears on the screen.

Adjust the focus of image by pressing the FOCUS ▲/▼ buttons

or POINT UP/DOWN buttons.

“Focus” disappears after 4 seconds.

NOTE:

• Focus adjustment may not function properly if the image is corrected by the

Keystone function.

LENS SHIFT ADJUSTMENT

Press the LENS SHIFT button on the top control or LENS SHIFT

▲/▼ buttons on the remote control. “Lens shift” appears on the

screen.

Press the POINT UP button or LENS SHIFT ▲ button to move

the image up, press the POINT DOWN or LENS SHIFT ▼ button

to move the image down.

“Lens shift” disappears after 4 seconds.

KEYSTONE CORRECTION

If a projected picture has keystone distortion, correct the image with the Keystone function.

Press the KEYSTONE button on the remote control or select

Keystone in the SETTING Menu. (See page 38.) The Keystone

dialog box appears.

Correct keystone distortion by pressing the POINT

UP/DOWN/LEFT/RIGHT buttons. Press the POINT UP button to

reduce the upper part of the image; press the POINT DOWN

button to reduce the lower part. Press the POINT LEFT button to

reduce the left part; press the POINT RIGHT button to reduce

the right part.

• Arrows are white when no correction.

• Arrow(s) in the corrected direction turn(s) red.

• Arrow(s) disappear(s) at the maximum correction.

• If you press the KEYSTONE button on the remote

control once more while the keystone dialog box is

being displayed, the Keystone function is canceled.

• “Keystone” disappears after 10 seconds.

Reduce the upper width

with POINT UP button.

Reduce the lower width

with POINT DOWN button.

Reduce the left part with

POINT LEFT button.

Reduce the right part with

POINT RIGHT button.

Download from Www.Somanuals.com. All Manuals Search And Download.

BASIC OPERATION

PICTURE FREEZE FUNCTION

Press the FREEZE button on the remote control to freeze the picture on the screen. To cancel the FREEZE

function, press the FREEZE button again or press any other button.

NO SHOW FUNCTION

Press the NO SHOW button on the remote control to black out

the image. To restore to normal, press the NO SHOW button

again or press any other button.

“No show” disappears after 4 seconds.

P-TIMER FUNCTION

Press the P-TIMER button on the remote control. A Timer

display “00 : 00” appears on the screen and starts to count time

(00 : 00 ~ 59 : 59).

To stop the P-TIMER, press the P-TIMER button. Press the P-

TIMER button again to cancel the P-TIMER function.

SOUND ADJUSTMENT

Indicates an approximate level of the volume.

DIRECT OPERATION

Volume

Press the VOLUME (+/–) buttons on the top control or on the remote

control to adjust the volume. A Volume dialog box appears on the

screen for a few seconds.

Press the VOLUME (+) button to increase the volume; press the

VOLUME (–) button to decrease the volume.

Mute

Press the MUTE button to set

the Mute function On or Off.

Press the MUTE button on the remote control to turn off the sound. To

restore the sound to its previous level, press the MUTE button again

or press the Volume (+/–) buttons.

The Volume dialog box disappears after 4 seconds.

MENU OPERATION

Press the MENU button to display the On-Screen Menu. Press

the POINT LEFT/RIGHT buttons to move the red frame pointer

to the SOUND Menu icon.

SOUND MENU

Press the POINT UP/DOWN buttons to move the red frame

pointer to the desired item, and then press the SELECT button.

SOUND Menu icon

Indicates an approximate

level of the volume.

Volume

To increase the volume, press the POINT RIGHT button; to decrease

the volume, press the POINT LEFT button.

Closes the SOUND Menu

Built-in SP.

Press the POINT LEFT/RIGHT buttons to switch the built-in speaker

On or Off.

Mute

Press the POINT LEFT/RIGHT buttons to turn off the sound. The

Dialog box display is changed to “On” and the sound is turned off. To

restore the sound to its previous level, press the POINT LEFT/RIGHT

buttons again.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

SELECTING INPUT SOURCE

DIRECT OPERATION

INPUT button

Input 1

Select an INPUT source by pressing the INPUT button on

the top control or the INPUT 1, INPUT 2, or INPUT 3 buttons

on the remote control.

✽

If the projector cannot reproduce proper image, select a

correct input source by MENU OPERATION (see below).

Input 2

Input 3

NOTE:

• Input 1 terminal is switchable and can be used as Computer Input or Monitor

Output.

✽Input 1 is not displayed when the Input 1 is used as

Monitor out.

MENU OPERATION

WHEN SELECTING INPUT 1 (COMPUTER INPUT TERMINALS )

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the INPUT Menu icon.

INPUT MENU

Press the POINT UP/DOWN buttons to move the red arrow

pointer to Input 1 and then press the SELECT button. A

Source Select Menu appears.

INPUT Menu icon

Move the pointer (red arrow) to Input 1

and press the SELECT button.

Move the pointer to a source that you want to select and then

press the SELECT button.

RGB (PC analog)

Input 1

When your computer is connected to the INPUT 1 (ANALOG)

terminal, select RGB (PC analog).

Source Select Menu

Move the pointer (red arrow)

to a source and press the

SELECT button.

RGB (Scart)

When scart video equipment is connected to the INPUT 1

(ANALOG) terminal, select RGB (Scart).

RGB (PC digital)

When your computer is connected to INPUT 1 (DIGITAL)

terminal, select RGB (PC digital).

RGB (AV HDCP)

If a HDCP-compatible signal source is connected to the

INPUT 1 (DIGITAL) terminal, select RGB (AV HDCP).

Monitor out

If the INPUT 1 ANALOG terminal is being used as a

MONITOR OUT terminal, select Monitor out.

NOTE:

• INPUT SOURCE changes if the INPUT 1 button on the remote control is

pressed.

• HDCP (High-bandwidth Digital Content Protection) is a system for protecting

digital entertainment content which is delivered by DVI (Digital Visual Interface)

from being copied. The specification of HDCP is decided and controlled by

Digital Content Protection, LLC. Should the specification be changed, this

projector may not display the digital content protected by HDCP.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )

When connecting a computer output [5 BNC Type (Green,

Blue, Red, Horiz. Sync, and Vert. Sync.)] from a computer to

G, B, R, H/HV, and V jacks:

INPUT MENU

INPUT Menu icon

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the INPUT Menu icon.

Move the pointer (red arrow) to Input 2

and press the SELECT button.

Press the POINT UP/DOWN buttons to move the red arrow

pointer to Input 2 and then press SELECT button. A Source

Select Menu appears.

Input 2

Press the POINT UP/DOWN buttons and a red-arrow icon

appears. Move the arrow to “RGB,” and then press the

SELECT button.

Source Select Menu

Move the pointer (red arrow)

to RGB and press the

SELECT button.

NOTE:

• INPUT SOURCE changes if the INPUT 2 button on the remote control is

pressed.

SELECTING COMPUTER SYSTEM

AUTOMATIC MULTI-SCAN SYSTEM

This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, SXGA+,

WXGA, or UXGA (refer to “COMPATIBLE COMPUTER SPECIFICATIONS” on pages 54-55). When Computer

is selected, this projector automatically detects the incoming signal and projects proper image without any

additional setting. (Some computers need to be set manually.)

The projector displays one of these: Auto, -----, Mode 1~10, or the system provided in the projector.

When the projector cannot recognize a connected signal

as PC system provided in this projector, the Auto PC

Auto

PC SYSTEM MENU

Adjustment function operates to adjust the projector and

“Auto” is displayed on the SYSTEM Menu icon.

When the image is not provided properly, a manual

adjustment is required. (See pages 27 and 28.)

PC SYSTEM Menu icon

Displays system being selected.

There is no signal input from the computer. Make sure

the connection of a computer and the projector is set

correctly. (See “TROUBLESHOOTING” on page 50.)

-----

The User preset adjustment in MANUAL PC

ADJUSTMENT. The Adjusted data can be stored in

the Mode 1~10.

Mode 1

SVGA 1

PC systems provided in this projector. The projector

chooses proper system and displays it.

✽ Mode 1 and SVGA 1 are examples.

PC SYSTEM MENU

SELECTING COMPUTER SYSTEM MANUALLY

This projector automatically selects PC system among those

provided in this projector, however, PC system can be also

selected manually.

PC SYSTEM Menu icon

Displays system being selected.

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the PC SYSTEM Menu icon.

Systems in this dialog box can be

selected.

Custom Mode (1~10) set in PC

ADJUST Menu. (p.27, 28)

Press the POINT UP/DOWN buttons to move the red arrow

pointer to the desired system, and then press SELECT button.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

PC ADJUSTMENT

AUTO PC ADJUSTMENT

Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and Vertical

positions to conform to your computer. Auto PC Adjustment function can be operated as follows.

Auto PC adj.

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the PC ADJUST Menu icon.

PC ADJUST MENU

Press the POINT UP/DOWN buttons to move the red frame

pointer to the AUTO PC adj. icon and then press the SELECT

button.

PC ADJUST Menu icon

This Auto PC Adjustment can be also executed by pressing

the AUTO PC ADJ. button on the top control or on the remote

control.

Move the red frame pointer to the Auto PC

adj. icon and press the SELECT button.

To store the adjusted parameters.

The system parameters from Auto PC Adjustment can be memorized in this

projector. Once the parameters are stored, the setting can be done just by

selecting Mode in PC SYSTEM Menu (p.25). See MANUAL PC

ADJUSTMENT on pages 27-28.

NOTE:

• Fine sync, Total dots, and Picture Positions of some computers can not be fully

adjusted with the Auto PC Adjustment function. When the image is not provided

properly with this function, manual adjustments are required. (See pages 27 and

28.)

• Auto PC Adjustment function cannot be operated in Digital Signal Input on the

DVI terminal and “480p,” “575p,” “480i,” “575i,” “720p (HDTV),” “1035i

(HDTV),” or “1080i (HDTV)” is selected on the PC SYSTEM Menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

MANUAL PC ADJUSTMENT

This projector can automatically tune to display signals from most personal computers currently distributed.

However, some computers employ special signal formats which may not be tuned by the Multi-Scan system of

this projector. If this happens, the projector cannot reproduce proper image and it may be recognized as a

flickering; non-synchronized; non-centered; or skewed picture.

Manual PC Adjustment of this projector enables you to precisely adjust several parameters to match with those

special signal formats. This projector has 10 independent memory areas to store those parameters manually

adjusted, which allows you to recall setting for a specific computer whenever you use it.

Note: The PC ADJUST Menu cannot be operated when the digital signal input on the DVI terminal is selected

on PC SYSTEM Menu. (p.25)

PC ADJUST MENU

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the PC ADJUST Menu icon.

PC ADJUST Menu icon

Press the POINT UP/DOWN buttons to move the red frame

pointer to the desired item, and then press the SELECT

Move the red frame pointer to an item

button. An Adjustment dialog box appears. Press the POINT

and press the SELECT button.

LEFT/RIGHT buttons to adjust the value.

Fine sync

Eliminate a flicker from the display. Press the POINT LEFT/RIGHT

buttons to adjust the value. (From 0 to 31.)

Shows status (Stored/Free)

of the selected Mode.

Total dots

Adjust the number of total dots in one horizontal period. Press the

POINT LEFT/RIGHT buttons to adjust the number to match your

PC image.

Selected Mode

Position H

Press the POINT LEFT/RIGHT

Press the POINT LEFT/RIGHT buttons to adjust the horizontal

buttons to adjust the value.

picture position.

Press the SELECT button at this icon

to adjust “Clamp,” “Display area H,” or

Position V

“Display area V.”

Press the POINT LEFT/RIGHT buttons to adjust the vertical picture

position.

Current mode

Press the SELECT button to show H-sync freq. and V-sync freq. of

the connected computer.

Current mode

Clamp

Adjusts the clamp level. When the image has a dark bars, try this

adjustment.

Press the SELECT

button at the Current

mode icon to show

information of the

Display area H

Adjust the horizontal area displayed by this projector. Press the

POINT LEFT/RIGHT buttons to decrease/increase the value.

computer connected.

Press the SELECT button at this icon

to display the previous items.

Display area V

Adjust the vertical area displayed by this projector. Press the

POINT LEFT/RIGHT buttons to decrease/increase the value.

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

Reset

To store adjustment data.

To reset the adjusted parameters, select Reset and press the

SELECT button. A confirmation box appears. Select [Yes]. All

the adjustments return to their previous figures.

This Mode has parameters being stored.

Mode free

To clear adjusted parameters previously set, move the red frame

pointer to the Mode free icon and then press the SELECT

button. Move the red arrow pointer to a Mode that you want to

clear and then press the SELECT button.

Store

To store the adjusted parameters, move the red frame pointer to

the Store icon and then press the SELECT button. Move the red

arrow pointer to any of the Mode 1 to 10 in which you want to

store the parameters and then press the SELECT button.

Close this dialog box.

Vacant

Shows the values of “Total

dots,” “Position H,” “Position V,”

“Display area H,” and “Display

area V.”

Quit

Exit the PC ADJUST Menu.

A confirmation box appears

and then select [Yes].

To clear adjustment data.

Close this dialog box.

A confirmation box appears

and then select [Yes].

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

PICTURE IMAGE SELECT

IMAGE LEVEL SELECT

DIRECT OPERATION

IMAGE button

Select an image level from among Standard, Real, and

Image 1 to Image 10 by pressing the IMAGE button on the

top control or on the remote control.

Standard

Real

Standard

Normal picture level preset on this projector.

Image 1

Real

Picture level with improved halftone for graphics.

Image 10

IMAGE 1~10

User preset picture adjustment in the IMAGE ADJUST Menu. (p.35-

37)

MENU OPERATION

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the IMAGE SELECT Menu icon.

IMAGE SELECT MENU

Press the POINT UP/DOWN buttons to move the red frame

pointer to the desired level and then press the SELECT

button.

IMAGE SELECT Menu icon

Standard

Move the red frame pointer to a level and

press the SELECT button.

Normal picture level preset on this projector.

Real

Picture level with improved halftone for graphics.

IMAGE 1~10

User preset picture adjustment in the IMAGE ADJUST Menu. (p.35-

37)

Download from Www.Somanuals.com. All Manuals Search And Download.

COMPUTER INPUT

PICTURE SCREEN ADJUSTMENT

PICTURE SCREEN SELECT

This projector has a picture screen resize function, which enables you to display the desirable image size.

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the SCREEN Menu icon.

SCREEN MENU

Press the POINT UP/DOWN buttons and move the red frame

pointer to the desired function and then press the SELECT

button.

SCREEN Menu icon

Move the red frame pointer to a function and

press the SELECT button.

Normal

Provides the image to fit the screen size.

True

NOTE:

• True, Full, and Digital zoom +/– cannot be operated when

“480i,” “575i,” “480p,” “575p,” “720p,” “1035i (HDTV),”

or “1080i (HDTV)” is selected on the PC SYSTEM Menu.

(p.25)

Provides image in its original size.

Wide

• The Screen Menu cannot be operated when “720p

(HDTV),” “1035i (HDTV),” or “1080i (HDTV)” is selected

on the PC SYSTEM Menu. (p.25)

• This projector cannot display any resolution higher than

1600 x 1200. If your computer’s screen resolution is

higher than 1600 x 1200, lower the resolution before

connecting the projector.

Provides the image to fit the wide video aspect ratio (16:9) by

expanding the image width uniformly. This function can be used to

provide the squeezed video signal at 16:9.

Full

Provides the full screen image.

• The image data other than XGA (1024 x 768) is modified to

fit the screen size in initial mode.

• The Panning function may not operate properly if the

computer system prepared on the PC ADJUST Menu is

used.

Digital zoom +

When the Digital zoom + is selected, the On-Screen Menu

disappears and “D. Zoom +” appears. Press the SELECT button to

expand the image size. Press the POINT UP/DOWN/LEFT/RIGHT

buttons to pan the image. The Panning function can work only

when the image is larger than the screen size.

The projected image can be also expanded by pressing the

D.ZOOM ▲ button on the remote control.

Digital zoom –

When the Digital zoom – is selected, the On-Screen Menu

disappears and “D. Zoom –” appears. Press the SELECT button to

compress the image size.

The projected image can be also compressed by pressing the

D.ZOOM ▼ button on the remote control.

To cancel the Digital Zoom +/– mode, press any button except

D.ZOOM ▲/▼, SELECT, POINT, and LASER buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO INPUT

SELECTING INPUT SOURCE

DIRECT OPERATION

INPUT button

Select an INPUT source by pressing the INPUT button on

the top control or the INPUT 1, INPUT 2, or INPUT 3 buttons

on the remote control.

If the projector cannot reproduce proper image, select a

correct input source through MENU OPERATION (see

below).

Input 1

Input 2

Input 3

✽Input 1 is not displayed when the Input 1 is used as

Monitor out.

MENU OPERATION

WHEN SELECTING INPUT 2 (5 BNC INPUT JACKS )

When connecting to video equipment, select a type of Video

source in the Source Select Menu.

INPUT MENU

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the INPUT Menu icon.

INPUT Menu icon

Move the pointer (red arrow) to Input 2

and press the SELECT button.

Press the POINT UP/DOWN buttons to move the red arrow

pointer to Input 2 and then press the SELECT button. A

Source Select Menu appears.

Input 2

Move the pointer to a source that you want to select and then

press the SELECT button.

Source Select Menu

When the video input signal is connected to the

VIDEO jack, select Video.

Video

Move the pointer (red arrow)

to Video or Y, Pb/Cb, Pr/Cr

and press the SELECT

button.

When the video input signal is connected to the Y-

Pb/Cb-Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.

Y, Pb/Cb, Pr/Cr

NOTE:

• INPUT SOURCE changes if the INPUT 2 button on the remote control is

pressed.

WHEN SELECTING INPUT 3 (AV TERMINALS )

When connecting to video equipment, select a type of Video

source in the Source Select (Video) Menu.

INPUT MENU

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the INPUT Menu icon.

INPUT Menu icon

Press the POINT UP/DOWN buttons to move the red arrow

pointer to Input 3 and then press the SELECT button. A

Source Select Menu appears.

Move the pointer (red arrow) to Input 3

and press the SELECT button.

Input 3

Move the pointer to a source that you want to select and then

press the SELECT button.

Source Select Menu

Move the pointer (red arrow)

to a source and press the

SELECT button.

When the video input signal is connected to the

Video

VIDEO jack, select Video.

When the video input signal is connected to the Y-

Pb/Cb-Pr/Cr jacks, select Y, Pb/Cb, Pr/Cr.

Y, Pb/Cb, Pr/Cr

When the video input signal is connected to the S-

VIDEO jack, select S-Video.

S-Video

NOTE:

• INPUT SOURCE changes if the INPUT 3 button on the remote control is

pressed.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO INPUT

SELECTING VIDEO SYSTEM

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the AV SYSTEM Menu icon.

Press the POINT UP/DOWN buttons to move the red arrow

pointer to the desired system and then press the SELECT

button.

VIDEO JACK OR S-VIDEO JACK

AV SYSTEM MENU (VIDEO OR S-VIDEO)

Auto

The projector automatically detects an incoming video system, and

adjusts itself to optimize its performance.

AV SYSTEM Menu icon

This box indicates system being

selected.

PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N

If the projector cannot reproduce proper video image, select a

specific broadcast signal format from among PAL, SECAM, NTSC,

NTSC 4.43, PAL-M, and PAL-N.

Move the pointer (red arrow) to

system and press the SELECT button.

Y, Pb/Cb, Pr/Cr JACKS

AV SYSTEM MENU (COMPONENT VIDEO)

Auto

The projector automatically detects an incoming video signal, and

adjusts itself to optimize its performance.

When the Video System is 1035i or 1080i, select the system

manually.

AV SYSTEM Menu icon

This box indicates system being

selected.

COMPONENT VIDEO SIGNAL FORMAT

Move the pointer (red arrow) to

system and press the SELECT button.

If the projector cannot reproduce proper video image, select a

specific component video signal format from among 480i, 575i,

480p, 575p, 720p, 1035i, and 1080i.

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO INPUT

PICTURE IMAGE SELECT

IMAGE LEVEL SELECT

DIRECT OPERATION

IMAGE button

Standard

Select an image level from among Standard, Cinema, Image

1 to Image 10 by pressing the IMAGE button on the top

control or on the remote control.

Cinema

Image 1

Standard

Normal picture level preset on this projector.

Cinema

Picture level adjusted for picture with fine tone.

Image 10

IMAGE 1~10

User preset picture adjustment in the IMAGE ADJUST Menu. (p.35-

37)

MENU OPERATION

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the IMAGE SELECT Menu icon.

IMAGE SELECT MENU

Press the POINT UP/DOWN buttons to move the red frame

pointer to the desired level and then press the SELECT

button.

IMAGE SELECT Menu icon

Move the red frame pointer to a level and

press the SELECT button.

Standard

Normal picture level preset on this projector.

Cinema

Picture level adjusted for picture with fine tone.

IMAGE 1~10

User preset picture adjustment in the IMAGE ADJUST Menu. (p.35-

37)

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO INPUT

PICTURE SCREEN ADJUSTMENT

PICTURE SCREEN SELECT

This projector has a picture screen resize function, which enables you to customize the image size.

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the SCREEN Menu icon.

SCREEN MENU

Press the POINT DOWN button and move the red frame

pointer to the desired function and then press the SELECT

button.

SCREEN Menu icon

Move the red frame pointer to a function and

press the SELECT button.

Normal

Provides image at the normal video aspect ratio of 4:3.

NOTE:

• SCREEN Menu can not be operated when “720p,”

“1035i,” or “1080i” is selected on AV SYSTEM Menu

(p.32).

Wide

Provides image at the wide screen ratio of 16:9.

Download from Www.Somanuals.com. All Manuals Search And Download.

PICTURE IMAGE

PICTURE IMAGE ADJUSTMENTS

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the IMAGE ADJUST Menu icon.

IMAGE ADJUST MENU

Press the POINT UP/DOWN buttons to move the red frame

pointer to the desired item and then press the SELECT

button. The level of each item is displayed. Adjust each level

by pressing POINT LEFT/RIGHT buttons.

IMAGE ADJUST Menu icon

Move the red frame pointer to item to be

selected and then press SELECT button.

Contrast

Press the POINT LEFT button to decrease contrast; press the

POINT RIGHT button to increase the contrast. (From 0 to 63.)

Brightness

Press the POINT LEFT button to decrease the brightness; press

the POINT RIGHT button to increase the brightness. (From 0 to

63.)

Color

Press the POINT LEFT button decrease the intensity of the color;

press the POINT RIGHT button to increase the intensity of the

color. (From 0 to 63.)

Tint

Press the POINT LEFT/RIGHT buttons to adjust the tint value to

obtain proper color balance. (From 0 to 63.)

Color Management

Press the POINT LEFT/RIGHT buttons to

adjust the value.

The Color management function can be used to adjust the LEVEL,

PHASE, and GAMMA of the selected display colors (except for

black, white, and gray) on the screen and replace these colors with

other colors if required.

You can store up to eight (8) color management data.

Press the POINT UP/DOWN buttons to move the red frame

pointer to Color management, and then press the SELECT

button. The image being projected freezes, and the COLOR

MANAGEMENT POINTER appears.

POINTER MODE

Use the POINT UP/DOWN/LEFT/RIGHT buttons to move the

pointer to a spot where you want to adjust the color and then

press the SELECT button. The COLOR SELECTION window

appears, and the color in the center of the pointer is selected

and you can adjust the color.

COLOR MANAGEMENT

POINTER

NOTE:

Use the POINT UP/DOWN/LEFT/RIGHT buttons to adjust the

Press the COLOR M. button on the remote control

to display the COLOR MANAGEMENT POINTER.

If you would like to check or readjust the color

management setting that has already been made,

press the COLOR M. button on the remote control

once more to display the COLOR MANAGEMENT

LIST.

LEVEL and PHASE of the color, and then press the SELECT

button to confirm the setting. Then use the POINT UP/DOWN

buttons to adjust the GAMMA for the color and press the

SELECT button to accept the setting. After adjusting, press

the SELECT button to go to the COLOR MANAGEMENT

LIST.

COLOR SELECTION MODE

LIST

Go to the COLOR MANAGEMENT LIST.

Download from Www.Somanuals.com. All Manuals Search And Download.

PICTURE IMAGE

COLOR SELECTION MODE (continued)

COLOR SELECTION MODE

COLOR M.

Level and phase

Gamma

adjustment palette.

Return to the COLOR MANAGEMENT POINTER. (If you

press the MENU button on the top control or the remote

control, it returns to the COLOR MANAGEMENT POINTER

and you will need to reselect and readjust the color.)

Return to the IMAGE ADJUST Menu. But any settings that

have been changed will not be stored. To store the changed

settings, be sure to select “LIST” and go to the COLOR

MANAGEMENT LIST.

In the COLOR MANAGEMENT LIST, the adjusted color data

are check marked. You can decide whether or not to apply

the adjusted color data in the list to the projected image (see

below).

LIST

COLOR M.

LIST MODE

Clear the check mark if you do not want to apply the adjusted

color data; select the check mark and then press the SELECT

button. The check make disappears.

COLOR PALETTE

DEL

COLOR PALETTE

Return to the COLOR SELECTION mode so that you can

readjust the setting for the color in that line. (This option is not

available if the check mark is cleared.)

DEL

Select the DEL box if you want to delete the adjusted data.

Press the SELECT button and a confirmation box appears

and then select [Yes]

ALL DEL

Delete all the data in the list. Press the SELECT button and a

confirmation box appears and then select [Yes].

ALL DEL

NOTE:

COLOR M.

The same function as stated above.

COLOR M.

If you press the COLOR M. button on the remote

control, the display returns to the normal projection

screen, but any settings that have been changed

will not be stored. To store the changed settings,

be sure to select “MENU” to return to the IMAGE

ADJUST Menu and store the settings.

The same function as stated above.

Auto picture control

Press the POINT LEFT/RIGHT buttons to select the desired Auto

picture control position (Off, L1 or L2).

Off . . . . Auto picture control OFF position.

L1 . . . . . Auto picture control LEVEL 1 position.

L2 . . . . . Auto picture control LEVEL 2 position.

Color temp.

Press either the POINT LEFT/RIGHT buttons to select the desired

Color temp. level (XLow, Low, Mid or High).

Download from Www.Somanuals.com. All Manuals Search And Download.

PICTURE IMAGE

White balance (Red)

Press the POINT LEFT button to lighten red tone; press the POINT

RIGHT button to deepen red tone. (From 0 to 63.)

White balance (Green)

Press the POINT LEFT button to lighten green tone; press the

POINT RIGHT button to deepen green tone. (From 0 to 63.)

White balance (Blue)

Press the POINT LEFT button to lighten blue tone; press the

POINT RIGHT button to deepen blue tone. (From 0 to 63.)

Press the SELECT button at this icon to

display other items.

Sharpness

Press the POINT LEFT button to decrease the sharpness of the

image; press the POINT RIGHT button to increase the sharpness of

the image. (From 0 to 31.)

Press the SELECT button at this

icon to display the previous items.

Gamma

Press the POINT LEFT/RIGHT buttons to adjust the gamma value

to obtain better balance of contrast. (From 0 to 15.)

Press the POINT LEFT/RIGHT

buttons to adjust the value.

Noise reduction

Noise interference on the screen can be reduced. Press the POINT

LEFT/RIGHT buttons to change the noise reduction mode.

Off . . . . Noise reduction mode is “Off”

L1 . . . . . For lower reduction

L2 . . . . . For higher reduction

Progressive

An interlaced video signal can be displayed in progressive. Press

the POINT LEFT/RIGHT buttons to change the progressive scan

mode.

Off . . . . Progressive scan mode is “Off.”

On . . . . Progressive scan mode is “On.”

Film . . . Select for watching a film. With this function, the

projector reproduces pictures faithful to the original film

quality.

NOTE:

• The Film mode in the Progressive function cannot be selected when the video

signal format is 1080i or 1035i.

Reset

To reset the adjusted parameters, select Reset and press the

SELECT button. A confirmation box appears. Select [Yes]. All the

adjustments return to their previous figures.

Image Level Menu

Move the red frame pointer to any of

Image 1 to 10 where you want to set

and then press the SELECT button.

Store

To store the manually preset image, move the red frame pointer to

the Store icon and press the SELECT button. The Image Level

Menu appears. Move the red arrow pointer to any of the Mode 1 to

10 in which you want to set and press the SELECT button.

Store icon

Press the SELECT button at this

icon to store the adjustment.

Quit

Exit the IMAGE ADJUST Menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING

SETTING MENU

This projector has Setting menu that allows you to set up the other various functions described as follows:

Press the MENU button to display the On-Screen Menu.

Press the POINT LEFT/RIGHT buttons to move the red frame

pointer to the Setting Menu icon.

SETTING MENU (LANGUAGE)

Press the POINT DOWN button to move the red frame pointer

SETTING Menu icon

to the desired item that and then press the

SELECT button.

The Setting dialog box appears.

Set the red frame pointer

to the item and press the

SELECT button.

Language

The language used in the On-Screen Menu is available in English,

German, French, Italian, Spanish, Portuguese, Dutch, Swedish,

Russian, Chinese, Korean, or Japanese.

Keystone

This function corrects distortion of a projected image. Select either

Store or Reset with the POINT LEFT/RIGHT buttons, and then

press the Select button. The Keystone dialog box appears. Correct

keystone with the POINT UP/DOWN/LEFT/RIGHT buttons. (p.22)

Store . . . stores the keystone correction even if the AC power

cord is unplugged.

When pressing the SELECT

button at Language, the

Language Menu appears.

Reset . . resets the keystone correction when the AC power cord

is unplugged.

Background

Three background settings are available in this projector. Select

one of the following options when no input source is connected to

the projector or no input signal is coming from the connected

equipment.

Blue . . . blue colored background

User . . . the image you captured

Black . . black colored background

Display

This function decides whether to display On-Screen Displays.

On . . . . . . . . . . . . shows all the On-Screen Display.

Count-down Off . . hide the Count-down Display.

Off . . . . . . . . . . . . hide the On-Screen Display except:

● On-Screen Menu

● “Power off?”

● P-TIMER (p.23)

● ”Please wait....”

● Color management operation screen (p.35-

36)

● “No signal” for Power management (p.40)

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING

Logo

This function allows you to customize the screen logo with Logo

select, Capture, and Logo PIN code lock functions.

Logo select

This function decides the start-up display as follows:

User . . . the image you captured

Default . the factory-set logo

Off . . . . count-down only

Capture

This function enables you to capture the image being projected

and use it for a starting-up display.

After capturing the projected image, go to the Logo select function

and set it to “User.” Then the captured image will be displayed

when turning on the projector the next time.

Select [Yes] to

capture the

projected image.

To capture the image, select [Yes]. To cancel the Capture

function, select [No].

NOTE:

Select [Yes] to stop

capturing.

• Before capturing an image, select Standard in the IMAGE SELECT Menu to

capture proper image. (See pages 29 and 33.)

• A signal from a computer can be captured up to XGA (1024 X 768).

• Certain signals may not be captured properly.

• When capturing the image that has been adjusted by the Keystone function,

the adjusted data is automatically reset and the projector captures an image

without keystone correction.

• When starting to capture a new image, the previously stored image is cleared

even if you cancel the capturing.

• Once you exit the Logo Menu after setting the Logo lock to "On," you are

required to enter the PIN code every attempting to change the Logo setting.

Logo PIN Code Lock Dialog Box

Logo PIN code lock

Pointer

This function prevents an unauthorized person from changing the

Logo setting.

Off . . . . the Logo setting can be changed freely from the Logo

function.

Quit

On . . . . the Logo setting cannot be changed without a Logo

PIN code.

After a correct Logo PIN code is entered, the following dialog box

appears.

If you want to change the Logo PIN code lock setting, enter a

Logo PIN code by following the steps below. The initial Logo PIN

code is set to “4321” at the factory.

To Enter a Logo PIN code

Select On/Off by pressing the POINT LEFT/RIGHT buttons or

change the Logo PIN code.

Select a number by pressing the POINT LEFT/RIGHT buttons and

fix the number with the SELECT button. The number changes to

“✳.” If you fixed a wrong number, move the pointer to “Set” or

“Clear” once by pressing the POINT DOWN button, then return to

“Logo PIN code.” Enter the correct number.

To Change the Logo PIN code

Logo PIN code can be changed to your desired

four-digit number. Select “Logo PIN code change”

with the POINT DOWN button and press the

SELECT button. Set a new Logo PIN code.

Repeat this step to complete entering a four-digit number.

When the four-digit number is fixed, the pointer automatically

moves to “Set.” Press the SELECT button so that you can change

the Logo PIN code lock setting.

Be sure to write down the new Logo PIN code and

keep it at hand. If you lost the number, you could

no longer change the Logo PIN code setting. For

details on the PIN code setting, refer to the

relevant instructions of the PIN code lock function

on page 43.

If you entered a wrong Logo PIN code, “Logo PIN code” and the

number (✳✳✳✳) turn red and disappear. Enter a Logo PIN code

all over again.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING

Ceiling

When this function is “On,” the picture is top/bottom and left/right

reversed. This function is used to project the image from a ceiling-

mounted projector.

Rear

When this function is “On,” the picture is left/right reversed. This

function is used to project the image to a rear projection screen.

Anamorphic

When this function is “On,” the screen image is forcibly changed to

the 4:3 image, even if the input signal is HDTV.

Simple menu

When this function is “On,” the value adjustment bar in the picture

IMAGE ADJUSTMENT Menu is displayed on the bottom left of the

screen.

Menu position

This function is used to adjust the On-Screen Menu display

position. When the SELECT button is pressed, the adjustment

screen is displayed (arrows appear). Use the POINT UP/DOWN/

LEFT/RIGHT buttons to adjust the position. After making the

adjustment, press the SELECT button to return to the Menu screen.

Power management

For reducing power consumption as well as maintaining the lamp

life, the Power management function turns off the projection lamp

when the projector is not used for a certain period.

If the input signal is interrupted and no button is pressed for more

than 30 seconds, the timer display with “No signal” appears on the

screen to start the countdown. The countdown time can be set

between 1 and 30 minutes.

Time left until lamp off

Select one of the following operations:

Ready . . . . . When the lamp has been fully cooled down, the

READY indicator starts blinking. In this condition,

the projection lamp is turned on if the input signal is

reconnected or any button on the top control or

remote control is pressed.

Shutdown . . When the lamp has been fully cooled down, the

power is turned off.

Off . . . . . . . The Power Management function is off.

Press the SELECT button at Power

management and this box appears.

Choose one of three settings with

the POINT LEFT/RIGHT buttons,

and go to the timer with the POINT

DOWN button and set time with the

POINT LEFT/RIGHT buttons.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING

On start

When this function is “On,” the projector is automatically turned on

just by connecting the AC power cord to an AC outlet.

NOTE:

• Be sure to turn the projector off properly (see “TURNING OFF THE PROJECTOR”

on page 21). If the projector is turned off in the incorrect sequence, such as

unplugging the AC power cord before completing the cool-down etc., the On

start function does not operate properly.

Lamp control

This function allows you to change the brightness of the screen.

. . . . brightness according to the input signal.

. . . . normal brightness.

. . . . lower brightness reduces the lamp power consumption

and extends the lamp life.

Remote control

The eight different remote control codes (Code 1-8) are assigned to

this projector: the factory-set, initial code (Code 1) and the other

seven codes (Code 2 to Code 8). This switching function prevents

interference from other remote controls when several projectors or

video equipment next to each other are operated at the same time.

For example, when operating the projector in “Code 7”, the code for

both the projector and the remote control must be switched to

“Code 7.”

To change the code of the projector:

Select from Code 1 to Code 8 in the SETTING Menu.

To change the code of the remote control:

Set the DIP switches 1-3 inside the battery compartment of the

remote control. (See page 15.)

When pressing the SELECT button at

Remote control, the Remote Control

Code Menu appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING

USB

This Projector has a USB port for interactive operation between the

projector and computers. Set the mode by following the steps

below.

Wireless Mouse mode

Select “

” when controlling a computer with the remote control of

this projector.

Projector mode:

“

” Not used.

Security

Key lock

This function locks operation of the top control and remote

control. It helps to prevent operation by an unauthorized

person.

. . . . unlocked.

. . . . locks operation of the top control.

To unlock, use the remote control.

. . . . locks operation of the remote control.

To unlock, use the top control.

Key lock

If the top control accidentally becomes locked and you do not

have the remote control nearby, unplug the AC power cord

from the AC outlet, and then hold down the SELECT button

and reinsert the AC power cord. This will cancel the top

control lock.

Select Key lock and

this box appears.

Choose one of the

alternatives with the

POINT UP/DOWN

buttons and select

[Yes] to activate it.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING

PIN code lock

This function prevents the projector from being operated by an

unauthorized person and provides the following settings for

security options.

Off . . . . the projector is not locked with the PIN code.

On1 . . . requires to enter the PIN code every time turning on

the projector.

On2 . . . requires to enter the PIN code to operate the projector

once the power cord is disconnected; as long as the

AC power cord is connected, the projector can be

operated without a PIN code.

When the projector is

locked with the PIN

code, the PIN code

lock mark appears on

the menu bar.

Whenever you change the PIN Code Lock setting or the PIN code

(the four-digit number), you are required to enter the PIN code.

“1234” is set as the initial PIN code at the factory.

To Enter a Logo PIN code

Select a number by pressing the POINT LEFT/RIGHT buttons and

fix the number with the SELECT button. The number changes to

“✳.” If you fixed a wrong number, move the pointer to “Set” or

“Clear” once by pressing the POINT DOWN button, then return to

“PIN code.” Enter the correct number.

Entering a PIN code

Pointer

Quit

Repeat this step to complete entering a four-digit number.

When the four-digit number is fixed, the pointer automatically

moves to “Set.” Press the SELECT button so that you can change

the PIN code lock settings.

The input numbers

change to “✳” for security.

If you entered a wrong PIN code, “PIN code” and the number

(✳✳✳✳) turn red and disappear. Enter a Logo PIN code all over

again.

When the pointer

automatically moves to

“Set,” press the SELECT

button.

To Change the PIN Code Lock setting

Select “Off,” “On1,” or “On2” with the POINT LEFT/RIGHT buttons

and then go to “Quit” with the POINT DOWN button. Press the

SELECT button to close the dialog box.

To Change the PIN Code

Changing the PIN code lock setting

The PIN code can be changed to your desired four-digit number.

Select “PIN code change” with the POINT DOWN button, and

press the SELECT button. A New PIN code input dialog box

appears.

Select a desired setting

with the POINT

LEFT/RIGHT buttons.

Select a number with the POINT LEFT/RIGHT buttons and fix the

number with the SELECT button. Repeat it to complete entering a

four-digit number. When the four-digit number is fixed, the pointer

automatically moves to “Set.” Then press the SELECT button.

Change the PIN code

Select PIN code

change and press the

SELECT button. The

New PIN code input

dialog box appears.

CAUTION:

WHEN YOU HAVE CHANGED THE PIN CODE, WRITE DOWN

A NEW PIN CODE IN COLUMN OF THE PIN CODE NO. MEMO

ON PAGE 60, AND KEEP IT SECURELY. SHOULD THE PIN

CODE BE LOST OR FORGOTTEN, THE PROJECTOR CAN NO

LONGER BE OPERATED.

The input numbers

are being displayed

for confirmation.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING

Factory default

Lamp counter

This function is used to reset the Lamp replacement counter. When

replacing the projection lamp, reset the Lamp replacement counter

with this function. See page 49 for operation.

Select Factory default and this box

appears. Select [Yes], and the next

box appears.

Factory default

This function returns all setting values except for the User logo,

Key lock, PIN code lock, Logo PIN code lock, and the Lamp counter

to the factory default settings.

Quit

Exit the SETTING Menu.

Select [Yes] to

activate it.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

WIRELESS MOUSE

Remote control is not only able to operate this projector but also functions as a wireless mouse for most

personal computers. The MOUSE POINTER, DRAG ON/OFF button, and two CLICK buttons are used for

wireless mouse operation.

The Wireless mouse function is available only when the PC mouse pointer is displayed on the screen.

INSTALLATION

To use the remote control as a wireless mouse for a computer, installation of a mouse driver (not supplied) is

required. Make sure that the mouse driver is properly installed on your computer and that the mouse port (or

USB port) of the computer is activated.

Connect the mouse port (or USB port) of your computer to the

CONTROL PORT (or USB connector) of this projector with

Note:When your computer has no mouse port,

connect the Serial port of your computer to

the Control cable (or USB cable). (See pages 12 and 13 for

the Control port of the projector with the

connection.)

Control cable for Serial port (supplied).

Turn on the projector first, and then turn your computer on. If

the computer is switched on first, the Wireless mouse function

may not work properly.

OPERATING WIRELESS MOUSE

When controlling the PC mouse pointer, use the MOUSE POINTER, DRAG ON/OFF button, LEFT CLICK

button, and RIGHT CLICK button on the remote control.

MOUSE POINTER

Used to move the PC mouse pointer. The pointer moves to the

direction you are pressing.

DRAG ON

INDICATOR

LEFT CLICK button

This button has the same function as the left button in a PC mouse.

To drag a selected screen object, hold down this button and press

the MOUSE POINTER.

RIGHT CLICK button

This button has the same function as the right button in a PC

mouse.

DRAG ON/OFF

button

DRAG ON/OFF button

MOUSE POINTER

(Moves the pointer)

Use this button and the MOUSE POINTER to drag a selected

screen object. Press and release the DRAG ON/OFF button, then

the DRAG ON INDICATOR lights green and the remote control is in

Drag mode. Use the MOUSE POINTER to drag an screen object.

Press and release the DRAG ON/OFF button again or press any

other button to drop the object.

LEFT CLICK button

(left button of the mouse)

RIGHT CLICK button

(right button of the mouse)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

MAINTENANCE

WARNING TEMP. INDICATOR

The Warning Temp. indicator blinks red to let you know the internal

temperature of the projector exceeds a normal level. If the temperature

goes up further, the projector will be turned off automatically and the

Ready indicator goes out. (The Warning Temp. indicator continues

blinking.) After the cooling-off period, the Ready indicator lights on again

and the projector can be turned on by pressing the POWER ON/OFF

button on the top control or the remote control. When you turn on the

projector, the Warning Temp. indicator goes out.

TOP CONTROL

If the Warning Temp. indicator is still blinking, check the following matters:

- The ventilation slots of the projector may be blocked. In such a case,

reposition the projector so that the ventilation slots are not obstructed.

- The air filters may be clogged with dust particles. Clean them by

following the section “AIR FILTER CARE AND CLEANING” on the next

page.

Warning Temp.

Indicator

Ready

Indicator

- If the WARNING TEMP. indicator remains on after performing above

checks, the cooling fans or internal circuits may be malfunctioning.

Contact the service station.

When both of the Warning Temp. and Ready indicators are blinking:

When the projector detects an internal problem, it shuts down automatically and both the Warning Temp. and

Ready indicators start blinking. In this condition, the projector cannot be turned on even if you press the POWER

ON-OFF button on the top control or remote control. If this happens, unplug and reconnect the AC power cord,

and then turn on the projector again to check the operation. If the projector shuts down again or cannot to be

turned on, internal checking and repair is required. Unplug the AC power cord and contact the service station.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

AIR FILTERS CARE AND CLEANING

Air filters help prevent dust from accumulating on the optical elements inside the projector. To whatever extent

the air filters become clogged with dust particles, the cooling fans’ effectiveness is reduced, which may result in

an internal heat build-up and adversely affect the life of the projector. Therefore, for appropriate care and use of

the projector, regular cleaning of the air filters is necessary.

How often the air filters should be cleaned really depends upon the environment in which the projector is being

operated. As a rough guide, under a normally clean operating environment, the air filters should be cleaned

approximately every 200 hours of use. However, if the projector is being operated in a somewhat dusty or

smoky environment, the air filters should be cleaned more often; for consistently good projector operation and

performance, timely cleaning of the air filters is a very important factor. When appropriate, clean the air filters

following the steps below.

Turn off the projector and unplug the AC power cord from an

AC outlet.

Turn over projector and remove the air filters by pulling the

latches upward.

Clean the air filters with a brush or rinse them softly. When

rinsing the air filters, dry them well.

Replace the air filters properly. Make sure that the air filters

are fully inserted to the projector.

CAUTION

AIR FILTERS

Do not operate the projector with the air filters

Pull up and remove.

removed. Dust may accumulate on the LCD Panel and

projection mirror degrading the picture quality. Do not

put anything into the air intake vents. It may result in

malfunction of the projector.

NOTE: If the dust cannot be removed by

cleaning, it is probably time to replace

the air filters with new ones. Please

consult your dealer.

Air Filter (A) Parts No. 610 303 8773

Air Filter (B) Parts No. 610 303 8780

RECOMMENDATION

We recommend avoiding dusty/smoky environments when operating the projector. Usage in these environments

may cause a poor image quality.

When using the projector under dusty or smoky conditions, dust may accumulate on a lens, liquid crystal panels, or optical

elements inside the projector. Such condition may degrade the quality of the projected image.

When the symptoms above are noticed, contact your authorized dealer or service station for proper cleaning.

CLEANING PROJECTION LENS

Follow these steps to clean the projection lens:

Turn off the projector and unplug the AC power cord from an AC outlet.

Apply a non-abrasive camera lens cleaner to a dry soft cleaning cloth. Avoid using an excessive amount of cleaner.

Abrasive cleaners, solvents ,or other harsh chemicals might scratch the surface of the lens.

Gently wipe with the cleaning cloth over the projection lens.

When the projector is not in use, put the lens cap.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

LAMP REPLACEMENT

When the projection lamp of this projector reaches its

end of life, the LAMP REPLACE indicator lights yellow. If

this indicator lights yellow, replace the projection lamp

with a new one promptly.

TOP CONTROL

This indicator lights yellow

when the projection lamp

reaches its end of life.

Replace the projection lamp

with a new one promptly.

CAUTION

Allow the projector to cool for at least 45 minutes

before you open the lamp cover. The inside of the

projector can become very hot.

CAUTION

For continued safety, replace with a lamp

assembly of the same type.

Do not drop the lamp assembly or touch a glass

bulb! The glass can shatter and may cause injury.

Follow these steps to replace lamp assembly.

Turn off the projector and unplug the AC power cord.

Allow the projector to cool for at least 45 minutes.

Loosen the two (2) screws with a screwdriver and open

the lamp cover.

Loosen the two (2) screws with a screwdriver and pull out

the lamp assembly by using the built in handle.

LAMP COVER

Replace the lamp assembly with a new one and tighten

the two (2) screws. Make sure that the lamp assembly is

set properly. Put back the lamp cover and tighten the two

(2) screws.

LAMP

ASSEMBLY

HANDLE

Connect the AC power cord to the projector and turn on

the projector.

Reset the Lamp replacement counter (refer to”LAMP

REPLACE COUNTER” on the next page).

NOTE:

• Do not reset the Lamp replacement counter when the projection lamp is

not replaced.

ORDER REPLACEMENT LAMP

Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following

information to the dealer.

● Model No. of your projector

● Replacement Lamp Type No.

LC-X71/LC-X71L

POA-LMP101

(Service Parts No. 610 328 7362)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

LAMP REPLACE COUNTER

Be sure to reset the Lamp replacement counter after the lamp assembly is replaced. When the Lamp

replacement counter is reset, the LAMP REPLACE indicator stops lighting.

Lamp counter

Turn the projector on and press the MENU button to display

the On-Screen Menu. Press the POINT LEFT/RIGHT buttons

to move the red frame pointer to the SETTING Menu icon.

Press the POINT UP/DOWN buttons to move the red frame

pointer to Lamp counter and then press the SELECT button.

The next box appears.

Press the POINT UP/DOWN buttons to select Reset and then

press the SELECT button. The “Lamp replacement counter

reset?” appears. Move the pointer to [Yes] and then press the

SELECT button.

Select Lamp counter and this box

appears. Select [Reset], and the

next box appears.

Another confirmation dialog box appears and select [Yes] to

reset the Lamp replacement counter.

Select [Yes], and then another

confirmation box appears.

NOTE:

• Do not reset the Lamp replacement counter until after the projection lamp is

replaced.

Select [Yes] again

to reset the lamp

counter.

LAMP HANDLING PRECAUTIONS

This projector uses a high-pressure lamp which must be handled carefully and properly. Improper

handling may result in accidents, injury, or create a fire hazard.

● Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no

guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a

shorter period of time than other similar lamps.

● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights

up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow

carefully the instructions in the LAMP REPLACEMENT section of this manual.) Continuous use of the

lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.

● Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its

lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in

which the projector and lamp are being used.

IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an

authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check

carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out

from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one

should check the inside of the projector except those who are authorized trained technicians and who are

familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who

are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken

glass.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

TROUBLESHOOTING

Before calling your dealer or service center for assistance, check the items below once again.

1. Make sure you have connected the projector to your computer or video equipment as described in

“CONNECTING PROJECTOR” on pages 12-14.

2. Check the cable connection. Make sure that all computers, video equipment, and power cords are properly

connected.

3. Make sure that all power is switched on.

4. If the projector still does not produce an image, restart your computer.

5. If an image still does not appear, disconnect the projector from your computer and check your computer

monitor’s display. A problem may be noticed with your graphics controller rather than with the projector.

(When you reconnect the projector, be sure to turn the computer and monitor off before you turn on the

projector. Turn on equipment in the order of the projector and computer.)

6. If a problem still persists, check the following solutions.

Problem:

No power.

Try these Solutions

● Plug the power cord of the projector into an AC outlet.

● Make sure the READY indicator lights.

● Wait 90 seconds after the projector is turned off to restart the projector.

NOTE: After pressing the POWER ON-OFF button to “OFF”, make sure the projector works

as follows:

1. LAMP indicator lights bright and the READY indicator turns off.

2. After 90 seconds, the READY indicator lights green again and the projector may

be turned on by pressing the POWER ON-OFF button.

● Check the WARNING TEMP. and READY indicators. If both indicators blink, the projector

cannot be turned on.

(See “TURNING ON/OFF PROJECTOR” on pages 20-21.)

● Check the projection lamp. (See page 48.)

● Adjust the focus of the projector.

● Make sure the projection screen is at least 4.6’ (1.4 m) away from the projector.

● Check the projection lens to see if it needs cleaning.

Image is out of

focus.

NOTE: Moving the projector from a cool to a warm place may result in moisture

condensation on the projection lens. If this happens, leave the projector off and wait

until condensation evaporates.

● Check the Ceiling/Rear function. (See “SETTING” on page 40.)

Picture is left/right

reversed.

● Check the Ceiling function. (See “SETTING” on page 40.)

Picture is top/bottom

reversed.

● Check the Display function.(See “SETTING” section on page 38.)

Some displays are

not seen during

operations.

● Check the connection between your computer or video equipment and the projector.

● When turning the projector on, it takes about 30 seconds to display the image.

● Check the system you selected is corresponding to your computer or video equipment.

● Make sure the temperature is not out of specified operating temperature (41 ˚F ~ 95 ˚F

(5 ˚C ~ 35 ˚C)).

No image.

● Check the audio cable connection from an audio input source.

● Adjust the audio source.

No sound.

● Press the VOLUME (+) button.

● Press the MUTE button.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Problem:

Remote control does

not work.

Try these Solutions

● Check the batteries.

● Check if the ALL-OFF switch on the remote control is set to “ON.”

● Make sure there is no obstruction in between the Infrared remote receiver of the projector

and the remote control.

● Make sure you are not too far from the projector when using the remote control.

Maximum operating range is 16.4’ (5 m).

● Check the remote control code in the remote control.

(See“SETTING” on page 41.)

● Check the cable connection between the projector and your computer.

● Check the mouse setting on your computer.

● Turn the projector on before turning on a computer.

Wireless mouse

function does not

work.

WARNING:

High voltages are used to operate this projector. Do not attempt to open the cabinet.

after following all operating instructions,

If the problem still persists

projector or the service center.

contact the sales dealer where you purchased the

Specify the model number and explain the difficulty. We will advise you how to obtain service.

This symbol on the nameplate means the product is Listed by Underwriters

Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety

standards against risk of fire, casualty, and electrical hazards.

The CE Mark is a Directive conformity mark of the European Community (EC).

Pixelworks ICs used.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

MENU TREE

Computer Input/Video Input

(1)

Input 1

RGB (PC analog)

RGB (Scart)

RGB (PC digital)

RGB (AV HDCP)

Monitor out

Video

Go to System

Input

(2)

(3)

(1)

(2)

(3)

(2)

Input 2

Input 3

Go to System

Y, Pb/Cb, Pr/Cr

RGB

Video

Y, Pb/Cb, Pr/Cr

S-Video

Computer Input

(1)

Mode 1

Mode 2

SVGA 1

SVGA 2

SVGA 3

Standard

Real

System

Image Select

Image 1

Image 10

✽ System displayed in the System Menu varies depending on the input signal.

Auto PC adj.

Normal

True

PC Adjust

Screen

Fine sync.

Total dots

Position H

Position V

Current mode

Clamp

0 - 31

Wide

Full

D.zoom +

D.zoom -

Display area - H

Display area - V

Reset

Yes/No

Mode free

Store

Mode 1

Mode 2

Mode 3

Mode 4

Mode 5

Mode 6

Mode 7

Mode 8

Mode 9

Mode 10

Quit

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Video Input

Computer Input/Vide Input

(2)

Auto

Language

English

German

French

Italian

System

Setting

PAL

SECAM

NTSC

NTSC 4.43

PAL-M

PAL-N

Spanish

Portuguese

Dutch

Swedish

(3)

Auto

1080i

1035i

720p

575p

480p

575i

Russian

Chinese

Korean

Japanese

Quit

Keystone

Background

Display

Store/Reset

Blue/User/Black

Off/Countdown Off/On

480i

Logo

Logo select

Standard

Cinema

Image 1

Capture

Image Select

Logo PIN code lock

On/Off

Logo PIN code change

Quit

Image 10

Quit

Ceiling

On/Off

Normal

Wide

Rear

Screen

Anamorphic

Simple menu

Menu position

Power management

Off

Computer Input/Vide Input

Ready

Shut down

1-30 Min.

Quit

Contrast

0 - 63

Image Adjust

Brightness

Color

0 - 63

Tint

0 - 63

On-Start

On/Off

Color management

Color

Lamp control

Auto/Normal/Eco

Gamma

List

Remote Control

All Del

Code 1

Color M.

Code 8

Quit

Auto picture control

Color temp.

Off/L1/L2

High

USB

Mouse

Projector

Mid

Low

Security

Key lock

Off

XLow

Projector

Remote Control

Quit

Red

0 - 63

Green

0 - 63

Blue

0 - 63

Sharpness

Gamma

Noise reduction

Progressive

Reset

0 - 31

PIN code lock

Off/On1/On2

PIN code change

Quit

0 - 15

Off/L1/L2

Off/On/Film

Yes/No

Image 1

Lamp counter

Factory default

Quit

Yes/No

Store

Image 10

Quit

Volume

Built-in SP

Mute

0 - 63

Sound

On/Off

Quit

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

COMPATIBLE COMPUTER SPECIFICATIONS

Basically this projector can accept a signal from all computers with V-, H-Frequency mentioned below, and less

than 140 MHz of Dot Clock.

ON-SCREEN

DISPLAY

H-Freq.

(kHz)

V-Freq.

(Hz)

ON-SCREEN

DISPLAY

H-Freq.

(kHz)

V-Freq.

(Hz)

RESOLUTION

VGA 1

VGA 2

VGA 3

VGA 4

VGA 5

VGA 6

VGA 7

MAC LC13

MAC 13

480i

640 x 480

720 x 400

640 x 400

640 x 480

31.47

37.86

37.50

43.269

34.97

35.00

15.734

15.625

31.47

31.25

35.156

37.88

46.875

53.674

48.08

37.90

34.50

38.00

38.60

32.70

38.00

49.72

48.36

68.677

60.023

56.476

60.31

48.50

44.00

63.48

36.00

62.04

61.00

35.522

46.90

47.00

58.03

60.24

59.88

70.09

74.38

72.81

75.00

85.00

66.60

66.67

60.00

50.00

59.88

50.00

56.25

60.32

75.00

85.06

72.19

61.03

55.38

60.51

60.31

51.09

60.51

74.55

60.00

84.997

75.03

70.07

74.92

60.02

54.58

79.35

87.17

77.07

75.70

86.96

58.20

58.30

72.00

75.08

MAC 21

SXGA 1

SXGA 2

SXGA 3

SXGA 4

SXGA 5

SXGA 6

SXGA 7

SXGA 8

SXGA 9

SXGA 10

SXGA 11

SXGA 12

SXGA 13

SXGA 14

SXGA 15 1280 x 1024

SXGA 16 1280 x 1024

SXGA 17

SXGA 18

SXGA 19 1280 x 1024

SXGA 20 1280 x 1024

SXGA 21 1400 x 1050

SXGA+ 1 1400 x 1050

SXGA+ 2 1400 x 1050

SXGA+ 3 1400 x 1050

1152 x 870

1152 x 864

1280 x 1024

1280 x 960

1152 x 900

68.68

64.20

62.50

63.90

63.34

63.74

71.69

81.13

63.98

79.976

60.00

61.20

71.40

50.00

63.37

76.97

61.85

46.43

63.79

91.146

63.90

63.97

65.35

65.12

75.00

80.00

48.36

47.70

48.36

56.16

75.00

81.25

87.50

93.75

45.00

37.50

33.75

28.125

75.06

70.40

58.60

60.00

59.98

60.01

67.19

76.107

60.02

75.025

60.00

65.20

75.60

86.00

94.00

60.01

72.00

66.00

86.70

60.18

85.024

60.00

60.19

60.12

59.90

75.08

60.00

72.00

60.00

65.00

70.00

75.00

60.00

50.00

60.00

50.00

––––––––

(Interlace)

––––––––

(Interlace)

––––––––

(Progressive)

––––––––

(Progressive)

575i

480p

575p

1280 x 1024

(Interlace)

SVGA 1

SVGA 2

SVGA 3

SVGA 4

SVGA 5

SVGA 6

SVGA 7

SVGA 8

SVGA 9

SVGA 10

SVGA 11

MAC 16

XGA 1

XGA 2

XGA 3

XGA 4

XGA 5

XGA 6

XGA 7

XGA 8

XGA 9

800 x 600

832 x 624

1024 x 768

1280 x 1024

(Interlace)

1152 x 900

1280 x 1024

(Interlace)

MAC

1280 x 960

1280 x 1024

1366 x 768

1360 x 768

1376 x 768

1360 x 768

1600 x 1200

WXGA 1

WXGA 2

WXGA 3

WXGA 4

UXGA1

UXGA2

UXGA3

UXGA4

720p

1035i

1080i

1024 x 768

(Interlace)

XGA 10

XGA 11

XGA 12

XGA 13

XGA 14

XGA15

MAC 19

1024 x 768

––––––––

(Progressive)

––––––––

(Progressive)

––––––––

(Interlace)

1024 x 768

(Interlace)

1024 x 768

––––––––

(Interlace)

––––––––

(Interlace)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

When a input signal is digital from DVI terminal, refer to the chart below.

ON-SCREEN

DISPLAY

H-Freq.

(kHz)

V-Freq.

(Hz)

ON-SCREEN

DISPLAY

H-Freq.

(kHz)

V-Freq.

(Hz)

RESOLUTION

✳

D-VGA

D-480p

D-575p

D-SVGA

D-XGA

640 x 480

31.47

31.25

37.879

43.363

48.36

47.70

48.36

46.50

63.98

59.94

59.88

50.00

60.32

60.00

50.00

60.02

D-SXGA2

D-SXGA+ 1

D-720p

1280 x 1024

1400 x 1050

60.276

63.97

45.00

37.50

33.75

28.125

33.75

28.125

27.00

58.069

60.19

60.00

50.00

60.00

50.00

60.00

50.00

48.00

720 x 480

(Progressive)

1280 x 720

768 x 575

(Progressive)

1280 x 720

(Progressive)

D-720p

800 x 600

1920 x 1035

(Interlace)

D-1035i

1024 x 768

1920 x 1080

(Interlace)

D-1080i

D-WXGA1 1366 x 768

D-WXGA2 1360 x 768

D-WXGA3 1376 x 768

D-WXGA5 1368 x 768

D-SXGA1 1280 x 1024

1920 x 1080

(Interlace)

D-1080i

D-1080psf/30

D-1080psf/25

D-1080psf/24

1920 x 1080

✳

✳ Depending on the condition of signals and the type and length of cables, these signals may not be properly viewed.

NOTE: Specifications are subject to change without notice.

INDICATORS AND PROJECTOR CONDITION

Check the indicators for projector condition.

Indicators

WARNING

TEMP.

red

LAMP

REPLACE

yellow

Projector Condition

READY

green

LAMP

red

The projector is OFF. (The AC power cord is unplugged.)

The projector is ready to be turned on with the POWER ON-

OFF button.

✽

The projector is operating normally.

The Warning Temp. indicator blinks red to let you know the

internal temperature of the projector exceeds a normal level. If

the temperature goes up further, the projector will be turned

off automatically and the Ready indicator goes out. When the

projector is cooled down enough and the temperature returns

to normal, the READY indicator lights green and the projector

can be turned on again. (The WARNING TEMP. indicator

keeps blinking.) Check and clean the air filters.

✽

The projector is cooled down enough and the temperature

returns to normal. When turning on the projector, the

WARNING TEMP. indicator stops blinking. Check and clean

the air filters.

✽

• • • on

• • • blinking

• • • dim

• • • off

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Indicators

WARNING

READY

TEMP.

green

LAMP

REPLACE

yellow

Projector Condition

LAMP

red

The projector is in cooling mode. It cannot be turned on until

the READY indicator lights green.

✽

The projector detects an abnormal condition and cannot be

turned on. Unplug the AC power cord and plug it again to turn

on the projector. If the projector is turned off again, disconnect

the AC power cord and contact the dealer or the service

center for service and checkup. Do not leave the projector on.

It may cause electric shock or a fire hazard.

The projector is in the Power management mode.

✽

The temperature inside the projector is abnormally high.

The lamp cannot light up. (The projector is preparing for

stand-by or the projection lamp is in cooling mode. The

projector cannot be turned on until the cooling process is

completed.)

The lamp cannot light up. (The lamp has been cooled down

enough and the projector is in stand-by mode and ready to be

turned on with the POWER ON-OFF button.)

The projection lamp reaches its end of life.

Replace the lamp and then reset the Lamp replacement

counter. The indicator is turned off.

✽

• • • on

• • • flashing

• • • dim

• • • off

*When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator

lights yellow, replace the projection lamp with a new one promptly. Reset the Lamp replacement counter after

replacing the lamp.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

TECHNICAL SPECIFICATIONS

Multi-media Projector

Projector Type

12.6” x 6.6” x 16.8” (319 mm x 170.8 mm x 435.5 mm)

19.8 lbs (9.0 kg) LC-X71, 18.0 lbs (8.2 kg) LC-X71L

1.3” TFT Active Matrix type, 3 panels

1024 x 768 dots

(W x H x D)

Dimensions

Net Weight

LCD Panel System

Panel Resolution

Number of Pixels

Color System

2,359,296 (1024 x 768 x 3 panels)

PAL, SECAM, NTSC, NTSC4.43, PAL-M, and PAL-N

480i, 480p, 575i, 575p, 720p, 1035i, and 1080i

H-sync. 15 k ~ 100 kHz, V-sync. 48 ~ 100 Hz

High Definition TV Signal

Scanning Frequency

Projection Lens

F1.8 ~ 2.1 lens with f=48.4 mm ~ 62.8 mm Motor zoom and focus (LC-X71)

4.6’ (1.4 m) ~ 48.3’ (14.7 m)

Up and Down

Throw distance

Motorized Lens Shift

Projection Image Size (Diagonal)

Horizontal Resolution

Projection Lamp

Input 1 Jacks

Adjustable from 31” to 400”

800 TV lines (HDTV)

300 watt type

DVI Terminal (Digital) HDCP Compatible, HDB 15-pin Terminal (Analog)

and Stereo Mini Type Jack (Audio)

BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H/V, and V),

Stereo Mini Type Jack (Audio)

Input 2 Jacks

Input 3 Jacks

Other Jacks

RCA Type x 3 (VIDEO/Y, Cb/Pb and Cr/Pr), RCA Type x 2 (Audio R and L)

and DIN 4-pin (S-Video)

DIN 8-pin (Control port), USB port (Series B receptacle), Wired Remote Jack

and Pj-to NetDirector Connector

INT. SP. Stereo (R and L), 3 watt RMS (T.H.D. 10%)

0˚ to 10.5˚

Built-in Speakers

Feet Adjustment

Voltage and Power

Consumption

AC 100 ~ 120 V (5.7 A Max. Ampere), 50/60 Hz (The U.S.A and Canada)

AC 200 ~ 240 V (2.7 A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.)

41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)

Operating Temperature

Storage Temperature

14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)

Power Source

Operating Range

Dimensions

Net Weight

Laser Pointer

AA or LR6 ALKALINE Type x 2

16.4’ (5 m)/ 30˚

2.0” x 1.4” x 7.6” (50 mm x 36 mm x 193 mm)

0.35 lbs (160 g) (including batteries)

Remote Control Transmitter

(Max. Output: 1mW/Wave length: 650 20nm)

Class II Laser

Owner’s Manual (CD-ROM)

Quick Reference Guide

AC Power Cord

Accessories

Wireless/Wired Remote Control Transmitter and Batteries

VGA Cable

USB Cable

Control Cable for Serial Port

Lens Cap (LC-X71)

Lens Attachment

Lens Replacement And Installation Manual

PIN Code Label

●

Specifications are subject to change without notice.

●

LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are effective, a tiny fraction of the pixels (0.01% or

less) may be ineffective by the characteristics of the LCD panels.

●

Each projector has its own characteristics.

When projecting with several projectors on the same screen or side by side, you may recognize different white balance and color uniformity on each

projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

CONFIGURATIONS OF TERMINALS

COMPUTER INPUT-1 TERMINALS (ANALOG)

Terminal: HDB15-PIN

Red Input

Green Input

Blue Input

Sense 2

+5V Power

Pin Configuration

10 Ground (Vert. sync.)

11 Sense 0

12 DDC Data

Ground (Horiz.sync.) 13 Horiz. sync.

Ground (Red)

Ground (Green)

Ground (Blue)

14 Vert. sync.

15 DDC Clock

COMPUTER INPUT-1 TERMINAL (DIGITAL)

Terminal: DVI 24-pin

T.M.D.S. Data2–

T.M.D.S. Data2+

T.M.D.S. Data1–

17 T.M.D.S. Data0–

18 T.M.D.S. Data0+

Pin Configuration

10 T.M.D.S. Data1+

T.M.D.S. Data2 Shield 11 T.M.D.S. Data1 Shield 19 T.M.D.S. Data0 Shield

No Connect

DDC Clock

DDC Data

12 No Connect

13 No Connect

14 +5V Power

15 Ground (for +5V)

16 Hot Plug Detect

20 No Connect

21 No Connect

22 T.M.D.S. Clock Shield

23 T.M.D.S. Clock+

24 T.M.D.S. Clock–

10 11 12 13 14 15 16

17 18 19 20 21 22 23 24

No Connect

CONTROL PORT CONNECTOR

Terminal: Mini DIN 8-PIN

PS/2

-----

Serial

R X D

-----

ADB

-----

Pin Configuration

CLK

DATA

GND

-----

ADB

-----

GND

-----

RTS/CTS

T X D

GND

-----

GND

-----

GND

USB CONNECTOR (Series B)

Pin Configuration

Vcc

- Data

+ Data

Ground

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

OPTIONAL PARTS

The parts listed below are optionally supplied. When ordering those parts, specify the item name and its Type

No. to the sales dealer.

● DVI Cable

Type No. : KA-DV20

● HDB 15 pin-SCART 21 pin Cable Type No. : AH-98881

● Long Zoom Lens

● Ultra Long Zoom Lens

● Short Zoom Lens

● Short Fixed Lens

● Remote Control Cable

● Pj-to NetDirector

Type No. : AH-23132

Type No. : AH-24241

Type No. : AH-23122

Type No. : AH-32011

Type No. : POA-CA-RC30

Type No. : PjNET-30

LENS REPLACEMENT

The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector

for wide variety of uses.

For installation and replacement of the lens, always contact the sales dealer. The projector lens must be

installed or replaced by well-trained sales or service engineers. Do not attempt to install and replace the lens by

yourself as it may cause injury.

After installing the lens, attach the lens cap to the lens when setting up the projector.

Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the projector.

To the sales and service engineer:

Referring to the attached lens replacement and installation manual, replace or install the lens properly.

PJ LINK NOTICE

This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information

System Industries Association). The projector supports all commands defined by PJLink Class 1 and is verified

conformance with PJLink Standard Class 1.

EIKI Projector Input

PJLink Input

RGB 1

Parameter

Input1

RGB (PC analog)

RGB (Scart)

RGB (PC digital)

RGB (AV HDCP)

Video

RGB 2

DIGITAL 1

DIGITAL 2

VIDEO 1

VIDEO 2

RGB 3

Input2

Input3

Y, Pb/Cb, Pr/Cr

RGB

Video

VIDEO 3

VIDEO 4

VIDEO 5

Y, Pb/Cb, Pr/Cr

S-video

PJLink is a registered trademark of JBMIA.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

PIN CODE NUMBER MEMO

Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost

the number and unable to use the projector, contact the service station.

PIN Code Lock No.

Factory default set No: 1 2 3 4*

Logo PIN Code Lock No.

Factory default set No: 4 3 2 1*

* Should the four-digit number be

changed, the factory set number will

be invalid.

While the projector is locked with the PIN code...

Put on the label below (supplied) in a prominent place of the

projector’s body while it is locked with a PIN code.

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

DIMENSIONS

12.6 (319.0)

5.59 (142.0)

Unit : inch (mm)

2.39 (60.6)

4.55 (115.5)

4.61 (117.0)

Screw Holes for Ceiling Mount

Screw: M6

Depth: 0.393 (10.0)

3.74 (95.0)

Download from Www.Somanuals.com. All Manuals Search And Download.

A-key to better communications

Canada

U.S.A.

EIKI International, Inc.

30251 Esperanza

EIKI CANADA - Eiki International, Inc.

P.O. Box 156, 310 First St. - Unit 2,

Midland, ON, L4R 4K8, Canada

Tel : 800-563-3454 (705)-527-4084

Fax : 800-567-4069 (705)-527-4087

E-Mail : [email protected]

Rancho Santa Margarita

CA 92688-2132

U.S.A.

Tel : 800-242-3454 (949)-457-0200

Fax : 800-457-3454 (949)-457-7878

E-Mail : [email protected]

Eastern Europe

EIKIˆ CZECH spol. s.r.o.

Umelecká 15

170 00 Praha 7

Czech Republic

Tel : +42 02 20570024

+42 02 20571413

Fax : +42 02 20571411

E-Mail : [email protected]

Deutschland & Österreich

EIKI Deutschland GmbH

Am Frauwald 12

65510 Idstein

Deutschland

Tel : 06126-9371-0

Fax : 06126-9371-14

E-Mail : [email protected]

Japan & Worldwide

EIKI Industrial Company Limited.

4-12 Banzai-Cho, Kita-Ku, Osaka,

530-0028 Japan

Tel : +81-6-6311-9479

Fax : +81-6-6311-8486

WorldWide Website http://www.eiki.com

1AA6P1P5253-- KE6B

Download from Www.Somanuals.com. All Manuals Search And Download.

Earthquake Sound Speaker 600WRMS User Manual
Eurotech Appliances Computer Accessories COM 1460 User Manual
FujiFilm Digital Camera 16315990 User Manual
Fusion Car Speaker CP AS1080 User Manual
Garmin Car Stereo System PAV80 User Manual
GE Cordless Telephone 00028056 User Manual
Geemarc Telephone TP38 User Manual
GE Food Warmer 169155 User Manual
Gigabyte Computer Hardware GA 945PLM DS2 User Manual
Gigabyte Network Card 6EA User Manual