IR-113E/IR-123E
User Manual
12-2012 / v1.2
Download from Www.Somanuals.com. All Manuals Search And Download.
3-9-2 Media......................................................................................................................... 47
3-9-3 Event Server............................................................................................................... 48
3-10 Recording to SD Card..............................................................................................52
Chapter IV Troubleshooting ........................................................................................ 59
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter I Introduction
1.1 Highlights of your new Network IP Camera
Congratulates on purchasing this high-resolution 3Mega pixels network IP
Camera! This IP Camera provides 3Mega pixels high-resolution video
quality, with the advanced megapixel lens, you can view images remotely
in more detail than conventional close-circuit cameras.
Other highlights of this network IP Camera include:
Ultra-high resolution 5Mega pixel CMOS image sensor.
Analog video (BNC) output, works with conventional video devices such
as TV Monitors, analog DVRs, etc.
Digital input / output interface lets you connect peripherals such as
external alarm, sensor, etc.
Audio input / output interface, you can listen to voices in remote place,
and speak to person in remote place.
Built-in SD-card slot for local storage, which can act like a stand-alone
DVR.
Two Way audio.
3GPP Mobile Surveillance Supported.
RS-485 communication supported.
ONVIF Compliant.
The IR-113E/IR-123E (PoE model) Supports IEEE802.3af Power over
Ethernet (PoE) standard.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 Safety Instructions
Please follow the safety instructions listed below when you’re using this
Network IP Camera, or you would harm this camera and / or yourself! Also,
the warranty will become void if you disobey these safety instructions.
This Network IP Camera is sophisticated electronic device; do not drop
it from high places.
Do not place this IP Camera at hot / humid places, and avoid direct
sunlight.
This IP Camera is not a toy; keep it out from the reach of children.
Do not insert any accessories of this IP Camera into your body.
Make sure lens set is secured when you’re using this IP Camera, lens set
may fall down if it’s not properly secured, and cause damage to human
and itself.
If you want to use this IP Camera at any place that may be spilled by
water or dirt, a secure and water-proof camera housing is required.
Do not pull any cord that is connected to this IP Camera by force.
IP Camera will become hot after long time of use. Refrain from touch IP
Camera with hand, or cover this IP camera with paper or cloth.
Never connect powered cable to IP Camera’s DI/DO contacts.
If the IP Camera falls into water when powered, do not attempt to
retrieve it back by yourself! Find a qualified electric technician for help.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Packaging Contents
Please check the contents of your new Network IP Camera when you
unpack the package. If any item is missing, please contact your dealer of
purchase for help.
Item No. Description
Quantity
1
2
3
Network camera
Power adapter
CD (with utility software, user manual &
multi-language QIG)
Quick installation guide
Sun shield kit
1
1
1
4
5
6
1
1
1
Bracket
1.4 Familiar with your new Network IP Camera
Item
Description
1. Sun shield
Protect camera device body from sun shine
or rain directly
2. I/O cable
Including
-Alarm I/O
-TV output
-Network
-Audio I/O
-RS485 +-
-Reset button
-GND
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. IP camera device
IP camera
[Front site]
Item
Description
1. IR-LED
Used for illumination assistance under night mode
2. Day/night sensor
Used for day/night detection and IR-LED ON/OFF
control
3. Lens
Fixed focal length.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
[Back]
Item
Description
1. Screw
Connects between camera device body & sun
shield.
2. Sun shield
Protect camera device body from sun shine or rain
directly
3. Camera device
body
IP camera metal case
4. Bracket mount
5. Cable glands
The portion to mount bracket
For water proof
5
Download from Www.Somanuals.com. All Manuals Search And Download.
[DI/DO PIN ASSIGNMENT]
Item
1
Description
Blue, Sensor IN1, for alarm input, DV3.3Volt level allowed.
2
Yellow, RS485 D-
3
Orange, RS485 D+
Black, GND
4
5
Green, Alarm out1, DV3.3Volt level allowed.
DC12Volt/2A input
Reset Button
6
7
8
Audio output
9
Audio input
10
Network, RJ45 connector, two LED index, orange color is
power index, green is network index
11
TV output, BNC connector
※Please check the I/O cable attached index before insert or release any
wire.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 Installation of the Network IP Camera
Please follow the instructions below to setup your new IP camera.
1. Connect Ethernet cable to LAN port.
2. Plug DC power adapter to power outlet on the wall.
3. Connect DC power cable to IP Camera’s DC power connector.
4. If everything’s ok, you should see the green LED light on LAN port light
up. If not, please recheck every step and try again, or ask your dealer of
purchase for help.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Remove the front glass mask to fine tune lens focus. When lens focus
fine tune ready, then screw the glass mask to the end position which
can not do any more.
IR-123E
IR-113E
6. Unplug the power then find the screws in the package, use screwdriver
to fix the sun shield on the device’s main body.
7. Secure the wall mounting metal bracket on the wall then secure the
bullet camera on the bracket.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The bracket is an optional extra.
8. Repower on the camera and refer to the following procedures to access
and configure it.
9. If this IP Bullet camera is connected to a PoE switch then the device can
be powered on without use the power adapter.
Note: The IR-113E/IR-123E (PoE model) supports IEEE 802.3af PoE
standard. It can be powered via the Ethernet cable when connected to a
PoE switch.
1.6 Locate the SD card slot
1. It is recommended that you use a tool with a hexagonal socket, such as
the socket spanner pictured below.
Note: The hexagonal socket is an optional extra.
2 Attach the socket spanner to the PVC tube cap, and twist
anti-clockwise to loosen the PVC tube.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Loosen the PVC tube as shown below, and then unscrew the back cover
to locate the SD Card slot.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter II Using Network IP Camera by Web
Interface
2.1 Locate the IP address of Network IP Camera
You can use your new Network IP Camera by its web user interface via web
browser. Currently the viewing system requirement for Network IP camera
is:
■
■
■
OS: Microsoft Windows XP/Vista/7
Browser: IE7, 8, or 9 (32bit)
Cell phone: 3GPP player
Note: For best viewing experience we recommend that you use Microsoft
Windows Internet Explorer 7, 8, or 9.
By default, the network camera automatically obtains an IP address from
the DHCP server on your local network. Check your DHCP server’s IP
address lease table to find the network camera’s IP address, or use the
EdiView Finder utility included in the CD.
Note: We recommend that you use Microsoft Windows to install your
network camera - Mac is not supported.
1. Insert the CD into your CD-ROM drive. When the wizard appears, click
“Setup Utility” to install the “EdiView Finder” software.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The contents of the CD-ROM can also be downloaded from the
2. After the installation is complete, double-click the “EdiView_Finder”
icon to execute the application.
3. Press ‘Discover’ button to search for all IP Cameras on your local
12
Download from Www.Somanuals.com. All Manuals Search And Download.
network (make sure all IP Cameras are powered on and connect to local
network first). When you find any IP Camera, you can double click on it
or click ‘Link’ button to connect to it by your web browser.
If you need to change a certain IP Camera’s IP address, you can also click
on the IP Camera you wish to change IP address, then click ‘Change IP’
button to change select IP Camera’s IP address setting.
If you no longer need to use this utility, click ‘Exit’ button to close it.
Please note:
If you have several network connections, such as “Wireless
Function”, please disable the “Wireless Functions” or/and
other network connections that is not connected to IP
camera, or IPFinder may fail to search IP camera!
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Connect to IP Camera’s Web User Interface and Install
ActiveX Plugin
When you know the IP address of IP Camera, you can connect to it by
Internet Explorer web browser by entering its IP address in address bar.
The use login screen will appear when you get connected:
IP Camera’s administrator username is ‘admin’ (lower case) and password
is ‘1234’ by default. Click ‘OK’ button or press ‘ENTER’ key on your
keyboard when you finish entering username and password.
When you connect to IP Camera for the first time, you’ll see the following
message. This message prompts you that you need to install ActiveX plugin
before you can see the video from IP Camera.
For IE 8 and earlier version:
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Right click the indication bar and click:
‘‘Install This Add-on for All Users on This Computer…’ to install ActiveX
plugin.
For IE 9:
Click ‘Install’ button located at the bottom of IE to install ActiveX plugin.
If you’re prompted that:
‘Windows Firewall has blocked some features of this program’
Click ‘Allow access’, or IP Camera will not be able to function properly.
When you’re installing Internet Explorer plugin, you may also be prompted
that if you want to allow changes to be made to your computer:
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Click ‘Yes’ to allow changes.
After ActiveX plugin is installed, you should be able to see the video
stream from camera.
NOTE:
If this is the first time you use this IP Camera, you can refer to
chapter 2.4 for instructions on Setup Wizard, which will guide
you to complete the software setup of your new IP Camera.
2.3 Viewing Live Video
After ActiveX control is installed, you can view IP camera’s video by web
browser. Just connect to IP camera by web browser and login, then you
can see live video from IP camera:
16
Download from Www.Somanuals.com. All Manuals Search And Download.
There are various controls on web page, here are descriptions of every
control item:
Item
Description
‘Home’ button
This button is visible in all setup pages of IP
camera, and you can go back to live video view
by clicking this button when you’re in other
page.
Stream
Select video stream type: H.264 or MJPEG.
H.264 required less network bandwidth and
this will help when network connection is slow.
Switch digital output interface on or off.
Digital Output
(ON / OFF)
Client Settings
Configuration
Language
Open ‘Client Setting’ menu.
Open ‘Configuration’ menu.
Open language menu, you can switch web
interface to other language.
Available languages: English, Simplified
Chinese, Traditional Chinese
Original size /
Fit screen
Switches live image view between original size
(full size: 3M pixels) and fit screen (smaller
size).
If you want to see video in detail, switch to
17
Download from Www.Somanuals.com. All Manuals Search And Download.
original size. If your computer monitor’s
resolution is not enough and you want to see
full image view, switch to fit screen and image
size will adjust automatically.
/
‘Connect’ button
Start live video view.
‘Disconnect’ button Stop live video view.
‘Snapshot’ button
Take a snapshot or camera video and save
image file on your computer. When you click
this button, a new window will appear:
Click ‘Save’ button when you see the image you
wish to save, and you’ll be prompted to indicate
the folder on your computer to save image file.
If you changed your mind and don’t want to
save image file, click ‘Cancel’.
‘Start Video Record’ Click this button to record video and save video
button
file on your computer. You’ll be prompted to
indicate the folder on your computer to save
video file.
‘Enable Digital
Zoom’ button
This function will enlarge video view digitally
from 1X to 10X, so you can see objects in video
in detail.
Please note: that digital zoom uses computer
18
Download from Www.Somanuals.com. All Manuals Search And Download.
algorithm to enlarge the video and some details
may lost. If you need to focus on detail of
specific objects in video view, please use optical
zoom ring on lens set of IP camera.
Enable / Disable
mute button
When mute is enabled ( ), you will not hear
the voice from IP camera; If you want to hear
voice from IP camera, click this button to
disable mute ( ).
/
You can drag the slide bar (
) beside
enable/disable mute button to adjust audio
playback volume.
Start / Stop talk
Button
Start or stop playing your voice through IP
camera’s audio output. When talk is stopped,
people at IP camera will not hear you.
/
Please note: you need a microphone connected
to your computer, and computer’s mixer setting
must enable microphone recording, or nothing
will be outputted by IP camera.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 Client Settings
In ‘Client Settings’ menu, you configure basic IP camera settings like data
transfer protocol and data storage folder.
To access ‘Client Settings’ menu, click ‘Client Settings’ button on the left.
The following screen will appear:
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are the descriptions of every setup item:
Item
Description
RTSP
Select this option to use RTSP (Real-Time
Streaming Protocol) to transfer video data.
Select this option to use HTTP (Hyper-Text
Transfer Protocol) to transfer video data.
If you don’t know which one you should use,
select ‘RTSP’.
HTTP
Folder
Prefix
Select a folder on your computer to save
recorded video. Click ‘Browse’ button and
you’ll be prompted to select a folder.
When saving video files, the characters you
typed in ‘Prefix’ field will be used as leading
characters of video file’s name.
For example, the default setting of ‘Prefix’ is
‘CLIP’, and video file’s named will be ‘CLIPxxxx’,
where xxxx is a 4-digit serial number.
Check this box to add data and time to the
ending part of video file’s filename, so you can
see the date and time the video file is created
directly from its filename.
Add date and time
suffix to file name
When you finish with above settings, click ‘Apply’ button to save changes.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter III Advanced Configuration
If you wish to configure IP camera’s settings, you can access IP camera’s
‘Configuration’ menu, which provides various kinds of system setting.
To access configuration menu, click ‘Configuration’ button on the left.
The ‘Configuration’ submenu will appear, please pick a setup item you
wish to configure.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
3-1 System
In this menu, you can configure basic IP camera settings like hostname and
time.
Here are the descriptions of every setup item:
Item
Description
Host Name
Input the IP camera’s hostname here, it can be
any meaningful words or characters that will
help you to identify this IP camera. You can use
IP camera’s installation location as host name,
and this will help you to identify IP camera when
you have many IP cameras installed.
Indicator LED
The LED lights located at the back of IP camera is
switched on by default. But, if you don’t want
other people to know the status of this IP
camera (so they will know this IP camera is
operating etc.), you can select ‘Off’ and LED
lights will be switched off.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Timezone
Select the time zone of residence from
dropdown menu to keep correct date and time.
If the area you live uses daylight saving, check
this box; otherwise do not check this box to keep
time correct.
Daylight Saving
Keep the current
date and time
Select this option and date / time setting will not
be changed when you click ‘Apply’ in the page.
You can check ‘Camera Date and Time’ item in
this page to know IP camera’s current date and
time setting.
Synchronize with
computer time
Synchronize with
NTP Server
Select this item and IP camera will use your
computer’s time as its time.
Select this item and IP camera will keep its date
and time setting synchronized with specified
time server (NTP server). Please input NTP
server’s IP address or host name in ‘NTP Server
Address’ field, and select time update interval
from ‘Update Interval’ dropdown menu.
Please note that if this IP camera can’t access
Internet, you must have a time server on local
area network, or set the time manually.
Set IP camera’s date and time manually. Please
set current date and time by ‘Date’ and ‘Time’
dropdown menu.
Set Manually
When you finish with above settings, click ‘Apply’ button to save changes.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2 Security
In this menu, you can configure IP camera’s login account.
There are three kinds of account:
- Administrator (Can view IP camera’s video and make changes of camera
setting)
- User (Can view IP camera’s video and see settings, but can’t make any
change)
- Guest (Can view IP camera’s video only)
There can be multiple users, but only one administrator is allowed, and
you can’t change administrator’s user name (it will always be
‘administrator’).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are the descriptions of every setup item:
Item
Description
Password / Retype
Password
(Administrator)
Input administrator’s new password in both
‘Password’ and ‘Retype Password’ field, and
click ‘Modify’ button to change administrator’s
password.
Please note: Don’t forget administrator’s
password! Or you’ll need to reset IP camera’s all
settings to get administrator’s password
recovered.
Account List
User Name
Here lists all users existed in IP camera. If you
want to remove one user, click it in the list, and
then click ‘Remove’ button.
If no user is existed, ‘New Account’ message will
be shown here.
Input new user’s username here. User name
must be greater than 1 character and less than
32 characters.
Password / Retype
Password
Input this user’s password in both ‘Password’
and ‘Retype Password’ field.
Authority
To define this user’s access privilege, select
‘User’ or ‘Guest’ in dropdown menu.
When you finish inputting new user’s
information, click ‘New’ button to create a new
user.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are the descriptions of every setup item:
Item
Description
LAN
Select this option to assign an IP address to LAN port (or
obtain an address from DHCP server automatically).
Available options are:
DHCP IPv4: Obtain an IPv4 IP address from DHCP server
on LAN automatically.
DHCP IPv4 / IPv6: Obtain both IPv4 and IPv6 address from
DHCP server on LAN automatically.
Static IPv4 / IPv6: Assign an IPv4 / IPv6 address to IP
camera manually. If you don’t have a DHCP server on your
local area network, you must use this option to specify an
IP address.
IP Address(IPv4): Input IPv4 IP address*
IP Address(IPv6): Input IPv6 IP address*
Prefix Length: Input IPv6 IP address’ prefix length
(0-128)
Subnet Mask: Input subnet mask
Gateway: Input gateway address
Primary DNS: Input DNS server’s IP address
Secondary DNS: Input backup DNS server’s IP address,
you can leave this field blank.
* You can leave this field blank, if you only wish to use
IPv4 or IPv6 IP address.
Enable UPnP Discovery: Check this b ox to enable other
devices on network to discover the presence of this IP
camera by UPnP. It’s recommended to enable this
function.
Enable UPnP Port Mapping: When UPnP is enabled, check
this box to enable UPnP’s port mapping.
PPPoE
Select this option to use PPPoE to connect to network. You
28
Download from Www.Somanuals.com. All Manuals Search And Download.
have to input PPPoE username and password assigned by
network operator to get connected.
HTTP Port
Input IP camera’s web connection port number here.
When this port number is changed, you need to change
web browser’s port number you used to connect to IP
camera.
For example, IP camera’s IP address is 192.168.2.3, and if
you changed HTTP port number to 82, please input
access IP camera’s web configuration interface.
Input RTSP port number. When this port number changes,
you must change corresponding settings in external
network devices (NVR or CMS software) so they can
receive this IP camera’s video.
RTSP Port
RTP Data Port
Input RTP data port number here.
When you finish with above settings, click ‘Apply’ button to save changes.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are the descriptions of every setup item:
Item
Description
Multicast Enable video multicast:
Multicast Group Address: Input multicast group
address here, must be an address between 232.0.0.0 to
232.255.255.255.
Multicast video port: Input port number for video multicast here.
Multicast RCTP video port: Input port number for RCTP video
here.
Multicast audio port: Input port number for audio here.
Multicast RCTP audio port: Input port number for RCTP audio
here.
Multicast TTL: Input TTL value for multicast here.
Bonjour If you’re using MacOS and you have Bonjour installed, you can use
it to discover this IP camera.
QoS
Enable QoS to improve the data transfer priority of this IP camera
(Your local area network must support QoS).
You can select Video / Audio’s QoS DSCP value (0 to 63), or both
video and audio.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
DDNS
Enable DDNS support if your ISP assigns dynamic IP address to
you. You must register a dynamic IP service first. Currently this IP
camera supports Dyndns, TZO and No-ip dynamic IP service.
Provider: Select dynamic IP service provider.
Host Name: Input the host name you obtained from dynamic IP
service provider.
User name: Input user name used to login dynamic IP service
provider.
Password: Input the password used to login dynamic IP service
provider.
*The user name and password should be under 16 characters.
Check ‘Enable HTTPS’ box to enable HTTPS channel to encrypt
transferred data. You can also define HTTPS port number in
‘HTTPS Port’ field if you don’t want to use default value ‘443’.
HTTPS
When you finish, click ‘Apply’ to save changes.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are the descriptions of every setup item:
Item
Description
Enable Filter
Check this box to enable IP address filter, uncheck
this Box to disable this function.
Accepted IP list Here lists all IP address that can build connections
to this IP camera. If you want to remove a set of IP
address from the list, click on the IP address and
click ‘Remove’ button.
IP Address
Input the starting and ending IP address of IP
(Accepted IP list) address you wish to accept connections here. IP
camera will only accept connections established
from these IP address.
If you want to specify one IP address only, input the
same IP address in both field.
Click ‘New’ button to add IP address into accepted
IP list.
Deny IP list
IP Address
Here lists all IP address that cannot build
connections to this IP camera. If you want to
remove a set of IP address from the list, click on the
IP address and click ‘Remove’ button.
Input the starting and ending IP address of IP
(Accepted IP list) address you wish to deny connections here. IP
camera will deny connections established from
these IP address.
If you want to specify one IP address only, input the
same IP address in both field.
Click ‘New’ button to add IP address into deny
IP list.
When you finish with above settings, click ‘Apply’ button to save changes.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
3-5 Video
You can adjust the image of the IP camera in this menu.
There are 3 sub-menus in this menu: Image Setting, Video Setting, and
Overlay, which can be accessed by tabs on the top:
3-5-1 Image Setting
You can adjust the image parameters in this page.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are the descriptions of every setup item:
Item Description
Brightness / Control the image parameters. Click ‘ - ' to decrease
Contrast / value, or click ‘ + ‘ to increase value. You can also input
Saturation / the value in the field directly.
Sharpness
Default
Mirror
Set all above values to default value ‘128’.
Check ‘Vertical’ or ‘Horizontal’ box to flip the image
vertically or horizontally, this will help to correct the
orientation of image when IP camera is hanged
bottom-up by camera holder.
You can click both ‘Vertical’ and ‘Horizontal’ box at the
same time.
Power Line
Frequency
Select the frequency of power line of the place you’re
using this IP camera. This will help to reduce the flicker
of certain lights in the image.
Condition
Select the condition that you’ll be using this IP camera
from dropdown menu.
- Auto: IP camera will adjust its parameters
automatically.
- Outdoor: Outdoor environment using.
- Night: You’ll be using this IP camera in dark places
where lights are insufficient.
- Tungsten: Low color temperature environment
using.
TV Out
IR-cut
Click “Enable” box to enable its “VIDEO OUT” function
for connections and video sending to TV monitors or
DVRs.
An IR-cut filter is built in this IP camera to reduce the
effect of IR lights (which will change the color of image
and makes it looks different than what you see through
your eye), and most of IR lights are coming from
sunlight.
You can select the behavior or IR-cut filter:
- Auto: IR filter will act automatically. If you don’t
know if you should use IR filter, select this option.
- Always ON: IR filter is always on.
Always OFF: IR filter is always off.
Day
IR-cut filter will only be switched on when there’s
36
Download from Www.Somanuals.com. All Manuals Search And Download.
sunlight. You can define the starting and ending time
when IR-cut filter should be switched on by select
‘Schedule’ and define starting and ending time by
dropdown menu.
When you finish with above settings, click ‘Apply’ button to save changes.
3-5-2 Video Setting
You can adjust the video transfer parameters in this page.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are the descriptions of every setup item:
Item
Description
H.264
/MPEG4
Video
Select the compression of main stream: H.264 / MPEG4.
Select video resolution.
Resolution - H.264:
2048x1536 (QXGA) / 1920x1080 (1080p)
1280x960 (960p) / 1280x720 (720p)
720x480 (D1)
320x240 (QVGA)
/ 640x480 (VGA)
- MPEG4:
1920x1080 (1080p) / 1280x960 (960p)
1280x720 (720p) / 720x480 (D1)
640x480 (VGA) / 320x240 (QVGA)
MJPEG:
1280x720 (720p) / 720x480 (D1)
640x480 (VGA) / 320x240 (QVGA)
Please note that some video resolution is not available
when video encoder is ‘MPEG4’.
When network speed is insufficient, select a lower video
resolution will help.
Frame Rate Select video frame rate. Please note that some frame
rate is not available when video encoder is ‘H.264’.
When network speed is insufficient, select a lower frame
rate will help.
Rate
Control
Select video bit rate. You can control bit rate by both
‘Video quality’ and ‘Bitrate’:
- Video quality: There are 5 levels of video quality,
select ‘very high’ to improve video quality but
consumes more network bandwidth, and select ‘very
low’ will decrease video quality and consumes less
network bandwidth.
- Bitrate: Input video’s bit rate directly. It must an
integer between 512 and 4000. Higher bit rate
provides better video quality, but consumes more
network bandwidth.
When you finish with above settings, click ‘Apply’ button to save changes.
Note:
MJPEG options are only available for portable devices like cell phone.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
3-5-3 Overlay Setting
You can adjust the video overlay parameters in this page.
Here are the descriptions of every setup item:
Item
Description
Enable Time
Stamp
Check this box to enable overlaying time stamp on
video.
Remove the
Check this box to remove time stamp’s
background color background color. You may find this will help the
of the text
readability of time stamp text in some cases.
(for Time Stamp)
Enable Text
Display
Check this box to display certain text on video, this
will help when you need to identify certain IP
camera when you have a lot of IP cameras.
Please input the text in ‘Text’ field. You can input
up to 15 characters.
Remove the
Check this box to remove custom text’s
background color background color. You may find this will help the
39
Download from Www.Somanuals.com. All Manuals Search And Download.
of the text (Text) readability of text in some cases.
Enable Image
Overlay
Check this box to overlay a specific image on
video, so you can show certain text / picture on
the video and help people to identify this IP
camera.
Click ‘Browse’ button to pick a picture on your
computer, then click ‘Update’ button to use the
picture. Please note that there are certain
restrictions:
- Select .bmp / .jpg / .jpeg image files only.
- Image’s resolution should be less than 160 x
128, and can be divided by 4.
- Do not upload image files that size is greater
than 64KB.
When you finish with above settings, click ‘Apply’ button to save changes.
3-6 Audio
You can adjust audio input / output parameters here.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are the descriptions of every setup item:
Item
Description
Enable
Microphone
Check this box to enable microphone. If you don’t
want to hear voice from IP camera, you can uncheck
this box to disable it.
Audio Type
(Microphone)
Microphone
Gain
The format is fixed as G.711
If the voice received by microphone is too loud or
silent, you can use this function to improve voice
volume, so you can hear voice from IP camera more
clearly.
- Select -2 or -1 dB to correct the voice that is too
loud;
- Select 0 dB and IP camera will do nothing on the
voice;
- Select +2 dB to +26 dB to amplify the voice.
Enable Speaker Check this box to enable speaker. If you don’t want
(Speaker)
people at IP camera to hear you, you can uncheck
this box to disable it.
Audio Type
(Speaker)
The format is fixed as G.711
When you finish with above settings, click ‘Apply’ button to save changes.
3-7 Motion
This IP camera is capable to detect object’s motion, so IP camera will only
record when there’s motion and save disk storage space.
Motion detection is performed by examine the movement of objects in
rectangular motion detection area. You can define up to 3 motion
detection areas.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are the descriptions of every setup item:
Item Description
Enable Motion Check this box to enable motion detection.
Detection
Enable
(Window 1 to
Window 3)
Check this box to enable this motion detection
window. You can select window 1 to 3 to enable up
to 3 motion detection windows. When a motion
detection window is enabled, a rectangular will
appear on camera’s view, with its title on the top.
- To move / resize a motion detection window:
- Move: Use the mouse to drag the title text.
- Resize: Use the mouse the drag the four corners
(upper-left/right, lower-left/right) to resize it. If
you only want to adjust width or height, drag the
four sidebars (top, bottom, left, and right).
Title
Input characters in title field to change motion
42
Download from Www.Somanuals.com. All Manuals Search And Download.
(Window 1 to
Window 3)
detection area’s title text so you can identify it.
Please note that you have to click ‘Apply’ button and
the text will change.
Percentage
Select the percentage of pixel change that will
trigger motion detection alert. Select a lower
percentage and you can detect tiny changes in
motion detection area.
Sensitivity
Select the sensitivity level that will trigger motion
detection alert. Select a higher sensitivity and you
can detect tiny changes in motion detection area.
When you finish with above settings, click ‘Apply’ button to save changes.
3-8 PTZ Control (RS-485)
If you mount the IP camera on pan-tilt camera cradles that support pan-tilt
control via RS-485 connection, you can use this function to control pan-tilt
camera cradle so you can control the orientation of IP camera from remote
place.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are the descriptions of every setup item:
Item Description
Enable RS-485 Check this box to enable RS-485 functionality.
Use Pelco-D
Select this option and RS-485 interface will output pan-tile
control signal in Pelco-D format. This format is widely
accepted by most of pan-tilt camera cradles.
You have also input pan-tilt camera cradle’s address code
in ‘Address’ field (number must be between 0~255). This
code must be identical to pan-tilt camera cradle’s address
code.
Use Custom
Protocol
When the pan-tilt camera cradle does not support Pelco-D
protocol, you can define a protocol’s detail by this function.
Please refer to pan-tilt camera cradle’s user manual to
define the protocol.
- Baud Rate: Select data baud rate of RS-485 interface
that pan-tilt camera cradle will accept. When the
length of RS-485 connection is very long (longer
than 200M), it’s not recommended to use high
speed connection (greater than 2400bps).
- Data Bits: Select data bits of RS-485 connection.
- Parity: Select parity bit: odd, even, or space.
- Stop Bit: Select stop bit: 1 or 2.
- Home/Up/Down/Left/Right: Input the command
string used to move pan-tilt camera cradle to home
or up/down/left/right position. You can click ‘Test’
button to send command string for testing.
- Command 1 ~ 5: You can define extra pan-tilt
camera cradle control strings here by giving it a
name (Command Name) and command string
(Hexadecimal Message). You can also click ‘Test’
button to send command string for testing.
When you finish with above settings, click ‘Apply’ button to save changes.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
3-9 Event
When there’s an event, you can use this setup page to define what IP
camera should do, like send an Email or trigger digital output to activate
external alarm.
There are three setup pages:
1. Setting: Define a new event and manage events.
2. Media: Define what kind of media file should be saved on designate
media.
3. Event Server: Define the details of remote server.
Please refer to following chapters for detailed instructions.
3-9-1 Settings
This page lists all existing events. You can click ‘Modify’ button to edit an
existing event, or ‘Remove’ to delete an existing event.
To create a new even, just click “New” button to add an Event setting.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
To add a new event, click ‘New’ button and the descriptions of every setup
item is listed below:
Item
Description
Enable Setting Check this box to enable this event. If you just want
to disable this event temporarily, you can uncheck
this box to keep this event and disabling while not
deleting it.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Title
Input any description text for this event so you can
identify it quickly. You can use alphabets, numbers,
and symbols include: !$-.@^_~ (no spaces allowed).
Check this box and this event will be activated when
one of motion detection window detects motion.
Check this box and this event will be activated when
digital input 1 or 2’s input signal is high or low (select
from dropdown list).
Motion
Detection
Digital Input
1 ~ 2
Enable
Check this box and this event will be activated when
Schedule Time designated weekday and time is reached.
You also have to check weekday box, and select time
from dropdown list. If you select ‘Always’ as time,
this event will be activated during all the day.
Enable FTP
Check this box and IP camera will save file on FTP
server (refer to ‘FTP Server’ setting in ‘Event Server’
tab) when this event is activated.
Enable EMAIL
Check this box and IP camera will send an Email to
designated recipient address (refer to ‘SMTP Server’
setting in ‘Event Server’ tab) when this event is
activated.
Enable Samba Check this box and IP camera will save file on samba
(Net Storage)
server (refer to ‘Samba Server’ setting in ‘Event
Server’ tab) when this event is activated.
Check this box and IP camera will save file on SD card
when this event is activated. A working SD card must
be inserted into IP camera in advance.
Enable SD
CARD
Trigger digital
output for xx
second(s).
Check this box and IP camera will trigger digital out
to ‘high’ state for xx seconds when this event is
activated, where ‘xx’ seconds must be defined by the
dropdown list.
3-9-2 Media
You can define what kind of media file should be saved on designated
media.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are the descriptions of every setup item:
Item Description
One Snapshot Save a picture file when event is triggered.
H.264 Video
Save a H.264 video clip. You can also select the
recording length before and / or after the time when
event is triggered in ‘Pre Event’ and ‘Post’ Event’.
For example, if you set ‘Pre Event’ to ‘2’ and ‘Post
Event’ to 3’, and an event is triggered at 14:10:30,
then the video file will be 5 seconds long, starting
from 14:10:28 to 14:10:33.
Tips: You may want to know what happened before
event is triggered in many cases, especially when
object is outside of motion detection window.
Note: If the “Pre Event” set to “0” second, the “Post
Event” cannot set to “0” second.
When you finish with above settings, click ‘Apply’ button to save changes.
3-9-3 Event Server
You can define the details of remote media server: FTP (File), SMTP (Email),
and Samba (File).
48
Download from Www.Somanuals.com. All Manuals Search And Download.
A Samba server can be any computer running windows operating system
with network neighbor function enabled. Many stand-alone network file
server also support samba server function.
Here are the descriptions of every setup item:
Item
FTP Server
Description
Check this box to enable FTP server upload.
- FTP Server: Input FTP server’s IP address or hostname.
- Port: Input FTP server’s port number. In most cases it should
be default value ‘21’.
- User Name: Input FTP server’s username.
- Password: Input FTP server’s password.
- File Path Name: Input the path where you want to save file
on FTP server, like ‘upload/record’. If you want to save file on
this FTP user’s home directory, you can leave this field blank.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
- Enable Passive Mode: Check this box to force IP camera to
communicate with FTP server in passive mode (Some FTP
Server may only work when you check this box, while others
don’t).
- Test FTP: Click this button to test FTP server settings above
immediately.
SMTP Server
Check this box to enable Email send.
- SMTP Server: Input SMTP server’s IP address or hostname.
- Port: Input SMTP server’s port number. In most cases it
should be default value ‘25’.
- Sender Email Address: Input the sender’s email address that
will appear in the Email send by IP camera. This will help you
to identify the Email sent by this IP camera, and may help
when you have anti-spam software installed (you can set this
Email address to ‘White List’ in your anti-spam software)
- Receiver #1 Email Address: Input primary recipient’s Email
address. This field is required.
- Receiver #2 Email Address: Input backup recipient’s Email
address. This field is optional.
- Subject: Input Email title that will appear in the Email send
by IP camera. This will help you to identify the Email sent by
50
Download from Www.Somanuals.com. All Manuals Search And Download.
this IP camera.
- Authentication: Check this box when authentication is
required by the Email server you’re using. You also need to
input Email server’s username and password in
corresponding field.
- Requires SSL Encryption: If your Email server required SSL
encryption, check this box. Please note that some Email
server uses different port number than standard port 25
when SSL encryption is used.
- STARTTLS: If your Email server required STARTTLS
encryption, check this box. Please note that some Email
server uses different port number than standard port 25
when STARTTLS encryption is used.
- Test SMTP: Click this button to test SMTP server settings
above immediately.
Samba Server
Check this box to enable Samba server file upload.
- Samba Server Address: Input Samba server’s IP address or
hostname.
- Path: Input the path where you want to save file on Samba
server, like ‘upload/record’. If you want to save file on this
user’s home directory, you can leave this field blank.
- User Name: Input Samba server’s username.
- Password: Input Samba server’s password.
* Username and password can NOT leave blank.*
- Test SMB: Click this button to test Samba server settings
above immediately.
Tips: Some samba server does not have username and
password check, you can just input samba server address and
path to access the file storage space.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
When you finish with above settings, click ‘Apply’ button to save changes.
3-10 Recording to SD Card
When a SD card is inserted into IP camera, you can save video files on it.
Note:
1. Be sure that the SD Card format should be FAT32. The NTFS
format cannot be supported by this camera.
2. Unlink motion detection, this function will record video at
specified time period on selected weekday(s).
Here are the descriptions of every setup item:
Item
Description
Enable External
storage Recording
Maximum Size of
Each File
Check this box to record video on SD card.
Input the maximum size of every video file from
1MB to 50MB. IP camera will start a new video
file when a recording video file reaches the size
limit stated here.
Recording
Schedule
Define the recording schedule. You can check
Sun to Sat boxes to represent a weekday, and
specify time period in ‘From’ and ‘To’ field.
Select ‘Always’ to record 24 hours in selected
weekday(s).
When you finish with above settings, click ‘Apply’ button to save changes.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
3-11 SDHC
The IP camera module has an optional SD card slot PCBA board. The
standard module does not include this board. The UI shows the capacity is
0 MB when the module without SD card slot and memory card.
f
you need the function please check the option when you place the order
of the IP camera module.
Once the module equipped SD card slot and SD card is inserted, the UI will
show the capacity of the SD card like the image hereunder.
There are two UI pages to show the record on the SD card. They are
mapping to the setting of “Recording to SD card” and “Event” accordingly.
Click “All file” to list all files. You also can define the range and click “Search”
to sort the files needed. It shows likes the images in the next page.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the time range then click “Search” then shows the records like below.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
3-12 Log
You can check the usage log of IP camera here.
In this page, you can click:
1. First page / Final page: Jump to first / final page of log.
2. Previous / Next: Jump to previous or next page of log.
3. Remove: Clear log. You’ll be prompted for confirmation.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
3-14 Maintenance
You can do some maintenance job about this IP camera here.
Here are the descriptions of every setup item:
Item
Description
Reboot
Click this button to reboot the IP camera. This
function is useful when you find IP camera is not
working properly.
Reset
Clear all settings of IP camera and reset to factory
default setting.
Backup
Backup to
Backup IP camera’s setting and save it on your
computer.
Backup IP camera’s setting and save it on Micro SD
Micro SD card card. A Micro SD card must be inserted into Micro SD
device
card slot when you click this button, or you’ll receive
an error message.
Restore
Restore a previously-saved configuration file saved
on your computer. Click ‘Browse’ button to select a
file on your computer first, then click ‘Restore’
57
Download from Www.Somanuals.com. All Manuals Search And Download.
button.
Restore from
Restore IP camera’s configuration which is
SD card device previously-saved on SD card.
Upgrade
Upgrade IP camera’s firmware. Click ‘Browse’ button
to select a firmware image file on your computer
first, then click ‘Upgrade’ button.
3-15 Language
You can change the display language of web interface.
Click ‘Language’ button and select one language. More languages may
available in latest firmware file.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter IV
Troubleshooting
Please don’t panic when you found this IP Camera is not working properly.
Before you send this IP Camera back to us, you can do some simple checks
to save your time:
Problem
description
Can’t
Possible solution(s)
1) Please check the IP address of IP Camera again.
connect to 2) Please make sure the network cable is correctly
IP Camera
connected to your local area network.
3) Please make sure power cable is correctly connected to
IP Camera.
4) Please make sure IP Camera is switched on (the LED
lights on IP Camera will light up).
No IP
Camera
found
1) ‘Auto search’ function only works on IP Cameras located
on local area network.
No image
1) If the place where IP camera is installed is too dark, try
to add some lights when possible.
2) Check if there’s anything covering the lens.
RTSP URL
1) Main Stream (H.264/MPEG4)
RTSP://IP address :RTSP port/stream1
2) MJPEG
RTSP://IP address :RTSP port/stream2
3) Mobile View
RTSP://IP address :RTSP port/mobile
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in conjunction with any other
antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation. Any changes or modifications not expressly approved by the party responsible for
compliance could void the authority to operate equipment.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure
limits, human proximity to the antenna shall not be less than 2.5cm (1 inch) during normal
operation.
Federal Communications Commission (FCC) RF Exposure Requirements
SAR compliance has been established in the laptop computer(s) configurations with PCMCIA
slot on the side near the center, as tested in the application for certification, and can be used in
laptop computer(s) with substantially similar physical dimensions, construction, and electrical
and RF characteristics. Use in other devices such as PDAs or lap pads is not authorized. This
transmitter is restricted for use with the specific antenna tested in the application for
certification. The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication
terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE
Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal
Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity
when working with electrical equipment. All guidelines of this and of the computer
manufacture must therefore be allowed at all times to ensure the safe use of the equipment.
EU Countries Intended for Use
60
Download from Www.Somanuals.com. All Manuals Search And Download.
The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria,
Cyprus, Czech, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia,
Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI version of this device is also
authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland.
EU Countries Not Intended for Use
None
61
Download from Www.Somanuals.com. All Manuals Search And Download.
EU Declaration of Conformity
English:
French:
This equipment is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC.
Cet équipement est conforme aux exigences essentielles et autres
dispositions de la directive 2004/108/EC.
Czechian: Toto zařízení je v souladu se základními požadavky a ostatními příslušnými
ustanoveními směrnic 2004/108/EC.
Polish:
Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi
warunkami określonymi Dyrektywą UE 2004/108/EC.
Romanian: Acest echipament este în conformitate cu cerinţele esenţiale şi alte
prevederi relevante ale Directivei 2004/108/EC.
Russian:
Magyar:
Türkçe:
Это оборудование соответствует основным требованиям и
положениям Директивы 2004/108/EC.
Ez a berendezés megfelel az alapvető követelményeknek és más
vonatkozó irányelveknek 2004/108/EC.
Bu cihaz 2004/108/EC direktifleri zorunlu istekler ve diğer hükümlerle ile
uyumludur.
Ukrainian: Обладнання відповідає вимогам і умовам директиви 2004/108/EC.
Slovakian: Toto zariadenie spĺňa základné požiadavky a ďalšie príslušné ustanovenia
smerníc 2004/108/EC.
German:
Spanish:
Italian:
Dieses Gerät erfüllt die Voraussetzungen gemäß den Richtlinien
2004/108/EC.
El presente equipo cumple los requisitos esenciales de la Directiva
2004/108/EC.
Questo apparecchio è conforme ai requisiti essenziali e alle altre
disposizioni applicabili della Direttiva 2004/108/EC.
Dit apparaat voldoet aan de essentiële eisen en andere van toepassing
zijnde bepalingen van richtlijn 2004/108/EC.
Dutch:
Portugese: Este equipamento cumpre os requesitos essênciais da Directiva
2004/108/EC.
Norwegian: Dette utstyret er i samsvar med de viktigste kravene og andre relevante
regler i Direktiv 2004/108/EC.
Swedish:
Danish:
Finnish:
Denna utrustning är i överensstämmelse med de väsentliga kraven och
övriga relevanta bestämmelser i direktiv 2004/108/EC.
Dette udstyr er i overensstemmelse med de væ sentligste krav og andre
relevante forordninger i direktiv 2004/108/EC.
Tämä laite täyttää direktiivien 2004/108/EC oleelliset vaatimukset ja muut
asiaankuuluvat määräykset.
---------------------------------------------------------------------------------------------------
--------------------
62
Download from Www.Somanuals.com. All Manuals Search And Download.
WEEE Directive & Product Disposal
At the end of its serviceable life, this product should not be treated as household or
general waste. It should be handed over to the applicable collection point for the
recycling of electrical and electronic equipment, or returned to the supplier for
disposal.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment
described below complies with the requirements of the European EMC directive
(2004/108/EC).
Equipment: 3Mpx Outdoor PoE True Day & Night Network Camera
Model No.: IR-113E
Report No.: T120302D06-E
The following European standards for essential requirements have been followed:
European Standard EN 55022:2006+A1: 2007, Class A
CISPR 22: 2008 (Ed 6.0)
EN61000-3-3:2008, EN61000-3-3:2008
EN 55024:1998+A1:2001+A2:2003
(IEC61000-4-2:2008
IEC 61000-4-3:2006 +A1:2007
IEC 61000-4-4:2004
IEC 61000-4-5:2005
IEC 61000-4-6:2008
IEC 61000-4-8:2009
IEC 61000-4-11: 2004)
Edimax Technology Co., Ltd.
No. 3, Wu Chuan 3rd Road,
Wu-Ku Industrial Park,
New Taipei City, Taiwan
Date of Signature: February 7, 2012
Signature:
Printed Name:
Title:
Albert Chang
Director
Edimax Technology Co., Ltd.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the
equipment described below complies with the requirements of the European
EMC directive (2004/108/EC).
Equipment: 3Mpx Outdoor PoE True Day & Night Network
Camera
Model No.: IR-123E
Report No.: T120424D17-E
The following European standards for essential requirements have been
followed:
European Standard EN 55022:2006+A1: 2007+A2: 2010,
Class A
EN61000-3-2:2006 + A1: 2009 + A2:2009
EN61000-3-3:2008
EN 55024: 2010
(IEC61000-4-2:2008
IEC 61000-4-3:2006 +A1:2007 +A2: 2010
IEC 61000-4-4:2004 + A1: 2010
IEC 61000-4-5:2005
IEC 61000-4-6:2008
IEC 61000-4-8:2009
IEC 61000-4-11: 2004)
Edimax Technology Co., Ltd.
No. 3, Wu Chuan 3rd Road,
Wu-Ku Industrial Park,
New Taipei City, Taiwan
Date of Signature: June 18, 2012
Signature:
Printed Name:
Title:
Albert Chang
Director
Edimax Technology Co., Ltd.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice According to GNU General Public License Version 2
This product includes software that is subject to the GNU General Public License version 2. The program
is free software and distributed without any warranty of the author. We offer, valid for at least three
years, to give you, for a charge no more than the costs of physically performing source distribution, a
complete machine-readable copy of the corresponding source code.
Das Produkt beinhaltet Software, die den Bedingungen der GNU/GPL-Version 2 unterliegt. Das
Programm ist eine sog. „Free Software“, der Autor stellt das Programm ohne irgendeine
Gewährleistungen zur Verfügung. Wir bieten Ihnen für einen Zeitraum von drei Jahren an, eine
vollständige maschinenlesbare Kopie des Quelltextes der Programme zur Verfügung zu stellen – zu nicht
höheren Kosten als denen, die durch den physikalischen Kopiervorgang anfallen.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA
02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is
not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By
contrast, the GNU General Public License is intended to guarantee your freedom to share and change
free software--to make sure the software is free for all its users. This General Public License applies to
most of the Free Software Foundation’s software and to any other program whose authors commit to
using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public
License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom to distribute copies of free software (and charge for
this service if you wish), that you receive source code or can get it if you want it, that you can change
the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to
ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you
distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the
recipients all the rights that you have. You must make sure that they, too, receive or can get the source
code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which
gives you legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that
there is no warranty for this free software. If the software is modified by someone else and passed on,
we want its recipients to know that what they have is not the original, so that any problems introduced
by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger
that redistributors of a free program will individually obtain patent licenses, in effect making the
program proprietary. To prevent this, we have made it clear that any patent must be licensed for
everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright
holder saying it may be distributed under the terms of this General Public License. The ‘“Program’“,
below, refers to any such program or work, and a ‘“work based on the Program’“ means either the
Program or any derivative work under copyright law: that is to say, a work containing the Program or a
portion of it, either verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term ‘“modification’“.) Each licensee is
addressed as ‘“you’“.
Activities other than copying, distribution and modification are not covered by this License; they are
outside its scope. The act of running the Program is not restricted, and the output from the Program is
covered only if its contents constitute a work based on the Program (independent of having been made
by running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any
medium, provided that you conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to
the absence of any warranty; and give any other recipients of the Program a copy of this License along
with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer
warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based
on the Program, and copy and distribute such modifications or work under the terms of Section 1 above,
provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices stating that you changed the
files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is
derived from the Program or any part thereof, to be licensed as a whole at no charge to all
third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it,
when started running for such interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a notice that there is no
warranty (or else, saying that you provide a warranty) and that users may redistribute the
program under these conditions, and telling the user how to view a copy of this License.
(Exception: if the Program itself is interactive but does not normally print such an
announcement, your work based on the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not
derived from the Program, and can be reasonably considered independent and separate works in
themselves, then this License, and its terms, do not apply to those sections when you distribute them as
separate works. But when you distribute the same sections as part of a whole which is a work based on
the Program, the distribution of the whole must be on the terms of this License, whose permissions for
other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by
you; rather, the intent is to exercise the right to control the distribution of derivative or collective works
based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a
work based on the Program) on a volume of a storage or distribution medium does not bring the other
work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2 above provided that you also do one of the
following:
a) Accompany it with the complete corresponding machine-readable source code, which must
be distributed under the terms of Sections 1 and 2 above on a medium customarily used for
software interchange; or,
67
Download from Www.Somanuals.com. All Manuals Search And Download.
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a
charge no more than your cost of physically performing source distribution, a complete
machine-readable copy of the corresponding source code, to be distributed under the terms
of Sections 1 and 2 above on a medium customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding
source code. (This alternative is allowed only for noncommercial distribution and only if you
received the program in object code or executable form with such an offer, in accord with
Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an
executable work, complete source code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to control compilation and installation of the
executable. However, as a special exception, the source code distributed need not include anything that
is normally distributed (in either source or binary form) with the major components (compiler, kernel,
and so on) of the operating system on which the executable runs, unless that component itself
accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place,
then offering equivalent access to copy the source code from the same place counts as distribution of
the source code, even though third parties are not compelled to copy the source along with the object
code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under
this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and
will automatically terminate your rights under this License. However, parties who have received copies,
or rights, from you under this License will not have their licenses terminated so long as such parties
remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants
you permission to modify or distribute the Program or its derivative works. These actions are prohibited
by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any
work based on the Program), you indicate your acceptance of this License to do so, and all its terms and
conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient
automatically receives a license from the original licensor to copy, distribute or modify the Program
subject to these terms and conditions. You may not impose any further restrictions on the recipients’
exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties
to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason
(not limited to patent issues), conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of
this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License
and any other pertinent obligations, then as a consequence you may not distribute the Program at all.
For example, if a patent license would not permit royalty-free redistribution of the Program by all those
who receive copies directly or indirectly through you, then the only way you could satisfy both it and
this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the
balance of the section is intended to apply and the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims
or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of
the free software distribution system, which is implemented by public license practices. Many people
have made generous contributions to the wide range of software distributed through that system in
reliance on consistent application of that system; it is up to the author/donor to decide if he or she is
willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of
this License.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by
copyrighted interfaces, the original copyright holder who places the Program under this License may add
an explicit geographical distribution limitation excluding those countries, so that distribution is
permitted only in or among countries not thus excluded. In such case, this License incorporates the
limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License
from time to time. Such new versions will be similar in spirit to the present version, but may differ in
detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this
License which applies to it and ‘“any later version’“, you have the option of following the terms and
conditions either of that version or of any later version published by the Free Software Foundation. If
the Program does not specify a version number of this License, you may choose any version ever
published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution
conditions are different, write to the author to ask for permission. For software which is copyrighted by
the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions
for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of
our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE
PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN
WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM ‘“AS
IS’“ WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Electro Voice Portable Speaker S 40T User Manual
Excalibur electronic Board Games PL26 User Manual
Fisher Price Baby Toy H1616 User Manual
Fisher Price Motorized Toy Car M7873 User Manual
Fisher Price Motorized Toy Car W2603 User Manual
Frigidaire Refrigerator 242046800 User Manual
Frymaster Fryer 8196329 User Manual
FUNAI CRT Television CR202EM9 User Manual
Gianni Industries Switch CP 21 GE User Manual
Giant Water Pump GP8055 User Manual