Eclipse Fujitsu Ten Car Stereo System 54420 User Manual

R
by FUJITSU TEN  
MODEL  
54420  
ESN E3 High-Power CD Receiver with  
CDC/E-COM/DSP Control and Wireless Remote  
OWNER'S MANUAL  
We appreciate your purchase of this receiver.  
Please read through this manual for correct operation.  
We suggest that after reading it you keep this manual  
in a safe place for future reference.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warning  
Do not place the vinyl storage bag over a person. It may  
cause a serious accident or death by suffocation.  
Do not adjust the controls while driving the car. To adjust the  
controls, stop the car in a safe location.  
To prevent accidents, store batteries for the remote control  
out of the reach of small children.In case a child swallows a  
battery, consult a physician immediately.  
Do not disassemble or rebuild this product. Doing so may  
cause an accident, fire or electrical shock.  
When it is necessary to replace the fuse, always use a fuse of  
the correct rating (number of amperes). Use of fuses with  
higher amperage ratings may cause a fire.  
Do not operate the product in a malfunctioning condition, for  
instance, when the audio does not play. Doing so may result  
in an accident, fire or electrical shock.  
If an abnormal situation occurs, such as foreign matter  
entering or liquid splashing on the product, or smoke or a  
strange odor emitting from the unit, shut off the product  
immediately and consult the dealer from whom you purchased  
it. Continued operation may cause an accident, fire or  
electrical shock.  
Caution  
Play the audio at a moderate volume level that permits you to  
hear sounds from outside the car. Driving without being able  
to hear outside sounds may result in an accident.  
Keep foreign objects out of the disc slot. They may cause fire  
or electrical shock. Another possibility is that discs may be  
damaged or become stuck.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caution  
Do not stick your fingers or hands into the disc slot. Doing so  
may cause personal injury.  
This product must be operated only as on-board equipment,  
or it may cause electrical shock or injury.  
Do not play distorted sounds for long periods of time;  
the speakers may overheat and cause a fire.  
This product uses an invisible laser light. In case a problem  
develops, be sure to consult the dealer from whom you  
purchased the product. Do not disassemble or rebuild the  
unit; rebuilding it may expose you and others to a dangerous  
laser emission (which would damage eyesight) or cause an  
accident.  
Never use batteries other than those specified. Do not mix  
new and old cells. Doing so may cause a fire or personal injury  
due to a battery explosion or chemical leaks.  
Pay attention to the (+) and (-) polarity of the battery when  
installing it in the product. Incorrect installation may cause  
personal injury or product damage due to a battery explosion  
or chemical leakage.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Operating Precautions ................................................ 8  
Notes on Operation........................................................................ 8  
About compact discs .................................................................... 9  
About cleaning a CD ................................................................... 11  
Names of controls and parts .................................... 12  
ESN (Key CD) Security Operating Procedure .......... 13  
How to program the Key CD ....................................................... 13  
How to cancel the Key CD .......................................................... 14  
How to change the Key CD ......................................................... 15  
How to resume normal operation (ESN security lock out) ............ 16  
What happens if an incorrect CD is inserted? .............................. 17  
How to turn the Security indicator on/off .......................................18  
How to Read the Electrical Serial Number ................................... 18  
Basic operation ......................................................... 19  
Turning the power on and off ...................................................... 19  
Listening to a CD ......................................................................... 19  
Listening to the tuner ................................................................... 20  
Adjusting audio volume ............................................................... 21  
Displaying the clock ..................................................................... 21  
Others ......................................................................................... 22  
How to operate the CD player .................................. 26  
Listening to CDs .......................................................................... 26  
Advancing to the next track or returning to  
the beginning of the track being played ....................................... 27  
Playing the beginning of tracks (SCAN) ........................................ 27  
Repeating the same track (REPEAT) ............................................ 28  
Playing tracks in random order (RANDOM) .................................. 28  
Switching the display ................................................................... 28  
Ejecting the disc .......................................................................... 29  
Displaying a genre for a CDs ....................................................... 30  
Switching the display ................................................................... 30  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the tuner .......................................... 31  
Tuning to a station ....................................................................... 31  
Entering stations into memory automatically  
(The automatic preset mode: ASM) ............................................. 32  
Manually setting stations into memory ......................................... 33  
Preset station scan ...................................................................... 34  
Switching the display ................................................................... 34  
FM reception characteristics ........................................................ 35  
How to use the Card remote control ........................ 38  
Precautions in use of the remote control ...................................... 38  
Cleaning the remote control ........................................................ 38  
Turning the power on/off ............................................................. 39  
Adjusting the audio volume .......................................................... 39  
Switching playback modes .......................................................... 39  
How to play the tuner .................................................................. 40  
How to play CDs ......................................................................... 41  
Replacing the battery .................................................................. 42  
How to use an optional NOB remote control ........... 43  
Turning the power on/off ............................................................. 43  
Adjusting the audio volume .......................................................... 43  
Switching playback modes .......................................................... 44  
How to play the tuner .................................................................. 44  
How to play CDs ......................................................................... 45  
Illuminating the NOB remote control ............................................ 46  
Replacing the battery .................................................................. 47  
How to operate the receiver with an optional CD  
changer connected ................................................... 49  
Basic operation ........................................................................... 49  
How to operate the receiver with an optional  
DSP/EQ unit connected ............................................ 53  
How to operate the DSP functions .............................................. 53  
How to operate the EQ functions ................................................ 57  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
If you have a question: .............................................. 60  
Displaying information (for troubleshooting) .................................. 61  
Specifications ............................................................ 64  
Before installation .......................................................66  
Components ............................................................................... 66  
Setting the system-selector switch .............................................. 66  
Mounting Instruction...................................................67  
Mounting the main unit................................................................. 67  
Names of lead wires and destinations ......................................... 69  
System ........................................................................................ 70  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating precautions  
ٟ
Operating Precautions  
<Your 54420 will perform well over a long period of time through correct  
handling and care.>  
Notes on Operation  
For your safety, play only at volume levels that allow outside sounds to  
be heard.  
Use only audio compact discs.  
This player can only play compact discs  
bearing the logo shown to the left.  
Do not insert anything other than a CD into  
the disc slot.  
Do not insert any foreign objects, such as  
coins or credit cards, into the disc slot. Be  
especially watchful of childrens mischief in  
this regard.  
Avoid severe mechanical shock.  
When the player is subjected to severe  
vibration while traveling over a rough  
surface, playback may be intermittent.  
When a situation like this occurs, resume  
playback after returning to a smoother  
road.  
About dew condensation  
In cold or rainy weather, just as the interior  
glass surface gets fogged, dew (water  
condensation) may also settle on the deck.  
When this occurs, disc playback may  
become intermittent or impossible.  
Dehumidify the air in the vehick for a while  
before resuming playback.  
Cleaning the disc slot  
The disc slot tends to get dusty. Clean it  
occasionally to prevent accumulated dust  
from scratching the discs.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating precautions  
About compact discs  
The signal recorded on a compact disc is read by a laser beam, so  
nothing touches the disc surface. A scratch on the recorded surface or  
a badly warped disc may cause deteriorated sound quality or  
intermittent playback. Observe the following precautions to ensure high  
quality sound performance:  
Do not leave an ejected disc in the disc  
slot for very long; the disc may warp.  
Discs should be stored in their cases and  
kept away from high temperature and  
humidity.  
Do not stick a piece of paper or tape on,  
nor write on or scratch, either side of a  
disc .  
Discs spin at a high speed inside the  
deck. Keep cracked or warped discs out  
of the player to avoid damaging it.  
Avoid touching the recorded surface when  
handling a disc; handle discs by their  
edges.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating precautions  
About brand new CDs  
About CD accessories  
You may notice that some brand  
new discs are rough around the  
center hole or outside edge.  
Remove the rough edges with  
the side of a ballpoint pen, etc.  
Rough edges may prevent  
proper loading in the deck.  
Flakes from the rough edges  
may also stick to the recorded  
surface and interfere with  
playback.  
Do not use accessories  
(stabilizers, protective seals, laser  
lens cleaners, etc.) sold for  
improving sound performance”  
or protecting CDs.The  
changes in CD thickness or  
outside dimensions made by  
these accessories may cause  
problems in the player.  
Rough Edges  
Ballpoint  
pen  
About borrowed CDs  
Do not use a CD with glue or  
remnants of adhesive tape or  
labels. They may cause the CD  
to get stuck inside or damage  
the deck.  
Rough  
Edges  
How to remove CDs  
Flakes  
When removing the ejected disc,  
pull it straight out along the slot.  
Pressing downward in the  
process may scratch the  
recorded surface of the disc.  
OKAY  
Recorded surface  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating precautions  
About irregularly-shaped CDs  
Specially-shaped CDs, like heart-  
shaped or octagonal CDs, cannot  
be played. Do not attempt to play  
them, even with an adapter, since  
they may damage the player.  
About cleaning a CD  
Use a commercially available compact disc  
cleaner to clean a CD, wiping lightly from  
the center to the edge.  
Do not use benzine, thinner, LP record  
spray or other cleaners on CDs. They may  
damage a CDs finish.  
XXXX  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Names of controls and parts  
ٟ
Names of controls and parts  
Front View  
[ EJECT] button  
[ASM] button  
[DISP] button  
[PWR] button  
[E-COM] button※  
[CD] button  
Buttons [1] to [6]  
[FUNC] button  
] buttons  
[
] buttons  
[FMAM] button  
DISC  
[
[AUDIO CONTROL] button  
NOTEDouble function button"E-COM"&"MUTE" functions  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESN (Key CD) security operating procedure  
[PWR] button  
Button [1]  
[FMAM] button  
ٟ
ESN (Key CD) security operating  
procedure  
ع
How to program the Key CD  
1 . Turn the vehicle’s ignition on. Press the [PWR]  
button or [FM• AM] button to activate the tuner  
mode.  
The tuner is now turned on.  
2 . Press and hold button [1], then the [FMAM]  
button, and hold both for more than one  
second.  
A [SEC] message appears, then in two seconds it will  
change to [DISC].  
The 54420 is now ready to accept your Key CD in the  
CD slot.  
3 . Insert the CD into the slot.  
A [SEC] message appears, the Key CD is ejected, then  
the tuner mode is activated.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESN (Key CD) security operating procedure  
[PWR] button  
Button [1]  
[FMAM] button  
If there is a problem with the inserted CD, an [ERR]  
message will appear for two seconds and the CD will be  
ejected. Reinsert the ejected CD.  
If a CD causes the [ERR] message to appear twice in a  
row, a [CHANGE] message will appear for two seconds.  
Try another CD.  
The Security indicator will flash whenever the vehicles  
ignition is switched off.  
ع
How to cancel the Key CD  
1 . Turn the vehicles ignition on. Press the [PWR]  
button or [FMAM] button to activate the tuner  
mode.  
The tuner is now turned on.  
2 . Press and hold button [1], then the [FMAM]  
button, and hold both for more than one  
second.  
A [SEC] message appears, then in two seconds it will  
change to [DISC].  
The 54420 is now ready to accept your Key CD in the  
3 . CD slot.  
Insert your Key CD into the slot.  
A [CANCEL] message appears, the Key CD is ejected,  
then the tuner mode is activated.  
The Key CD is cancelled.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESN (Key CD) security operating procedure  
This process cancels the protection for the ESN  
deck.  
If power to the 54420 is disconnected, then  
reconnected, a key CD will not need to be inserted in  
order to return the unit to normal operation.  
Inserting a CD other than the Key CD will not cancel the  
protection. Instead, the display will show [ERR] for two  
seconds, then the normal CD playback mode will activate.  
ع
How to change the Key CD  
1 . First, cancel the existing Key CD.  
Refer to How to cancel the Key CD.”  
2 . Next, program a new Key CD.  
Refer to How to program the Key CD.”  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESN (Key CD) security operating procedure  
ع
How to resume normal operation  
(ESN security lock out)  
If power to the 54420 is disconnected while ESN security is  
active (a Key CD was programmed), operation is disabled  
until power is restored and the unit unlocked. Follow this  
procedure to resume normal operation.  
1 . When the power is turned on after  
disconnecting the battery power, a [SEC]  
message will appear for two seconds.  
Thereafter, the message changes to [DISC]  
and the 54420 is ready to accept your Key CD  
into the slot.  
2 . Insert your Key CD.  
If the correct CD is inserted, an [OK] message will  
appear for two seconds and the CD will begin playing.  
If an incorrect CD is inserted, an [ERR] message will  
appear for two seconds, after which the CD will be  
ejected.  
You must use the same CD used for Key CD  
programming; a duplicate CD may not work properly.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESN (Key CD) security operating procedure  
ع
What happens if an incorrect CD is  
inserted?  
1 . An [ERR_] message will be appear, then  
change to a flashing [DISC], then the CD will  
be ejected.  
You will have five uninterrupted attempts to insert the  
correct CD.  
th  
2 . After the 5 incorrect attempt, the display  
reads [CALL800] and the security indicator  
lights steadily.  
Number of errors: Numbers indicated at _ show the  
number of errors that occurred.  
٨
٨
Note  
If after 5 tries the correct Key CD is not insereted, the  
display reads [CALL 800]; the unit must be returned to  
Eclipse to be reset. In this case, please contact your  
Eclipse dealer for assistance or call Eclipse directly at  
(800)233-2216  
Your key CD can be easily forgotten. Write  
the album name in a reminder note (Pg.75).  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ESN (key CD) security operating procedure  
[DISP] button  
[PWR] button  
Button [4]  
[FMAM] button  
ع
How to turn the Security indicator on/off  
Once ESN security is activated, the indicator flashes  
whenever the vehicles ignition is turned off, warning  
potential thieves that the unit is protected. However, if you  
do not want this visible deterrent, it may be turned off.  
1 . With the tuner mode ON, press the [DISP]  
button, then [FMAM] button and hold both for  
more than a second.  
2 . [INDICATOR flash] or [INDICATOR OFF] appears  
on the display.  
[IND FLASH] means the security indicator will flash when  
the vehicles ignition is off, and [IND ---] means it will  
not. Repeat the above steps to reactivate the flash  
mode.  
ع
How to Read the Electronic Serial Number  
1 . Turn the vehicles ignition on; press the [PWR]  
button or [FMAM] button to activate the tuner  
mode.  
2 . Press button [4], then the [FMAM] button, and  
hold both for more than a second.  
[ESN] appears on the display, followed by an eight-digit  
number; this number is your electronic serial number (ESN).  
You may use this number to identify your Eclipse 54420 in  
the event it is recovered after being stolen.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic operation  
[CD] button  
[PWR] button  
Buttons [1] to [6]  
[
] buttons  
[FMAM] button  
Basic operation  
ٟ
This s e c tion c ove rs b a s ic op e ra ting p roc e d ure s .For  
additional details, please refer to the sections on specific  
functions.  
ع
Turning the power on and off  
1 . Press the [PWR] button.  
Pressing the button turns the power on and off.  
Less than two seconds Stand by  
More than two seconds Off  
If a car is not eguipped with an ACC position (for example,  
a European car), keep the [PWR] button depessed for more  
than two seconds.  
You may also press the [FM• AM] button to turn on the  
power. (When there is a disc loaded, you may press the  
[CD] button to turn on the power.)  
ع
Listening to a CD  
1 . Insert a CD into the disc slot, label side up.  
The CD will immediately start playing.  
When a CD is already loaded, pressing the [CD] button  
starts playing the disc.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic operation  
ع
Listening to the tuner  
1 . Press the [FM• AM] button.  
This will turn the tuner on.  
To turn the tuner off, either press the [PWR] button or  
2 . select another mode.  
Tap the [FMAM] button to switch to the  
desired FM or AM bands.  
Each additional tap of the button switches the preset  
station sets from FM1 to FM2, FM3, then AM in  
sequence.  
3 . Press the [  
] button to tune to a station.  
or ] button for less than one  
A tap on either the [  
]
[
button second will enable manual station tuning. Hold  
one button down for more than two seconds to start the  
automatic station search.  
[
[
] button: Starts searching toward higher frequencies.  
] button: Starts searching toward lower frequencies.  
If stations have been stored in memory, pressing a button  
from [1] to [6] will directly select a station. (Refer to the  
section Manually setting stations into memoryon page  
33.)  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic operation  
[E-COM] button  
[DISP] button  
Button [6]  
[FUNC] button  
[AUDIO CONTROL] button  
ع
Adjusting audio volume  
1 . Turn the [AUDIO CONTROL] button to the  
left or right.  
Turn to the left : Decreases the volume.  
Turn to the right : Increases the volume.  
Press and hold the [E-COM] button for more than two  
seconds to activate or cancel MUTE function.  
Warning  
Do not adjust the volume or other controls while driving the  
vehicle. Do so only while parked in a safe location.  
ع
Displaying the clock  
1 . Press the [DISP] button repeatedly until  
the time is displayed.  
Refer to the section on setting the clockto set  
the time display.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic operation  
ع
Others  
ٕ
Disabling the guide tone feature (for button  
operation)  
The receiver is set at the factory to emit a beep tone in  
response to button operation. The guide tone feature may  
be disabled in the following procedure:  
1 . Press and release the [FUNC] button.  
2. P re s s a nd hold b utton[6] until the [BEEP OFF]  
display appears on the screen.  
Pressing the button will switch modes between the  
[BEEP ON] and the [BEEP OFF].  
3. Press the [FUNC] button again.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic operation  
[DISP] button  
Buttons [1] to [5]  
[AUDIO CONTROL] button  
ٕ
Setting the clock  
This receiver uses the 12-hour, A.M./P.M.display notation.  
1 . Press the [DISP] button repeatedly to switch to the  
clock display mode.  
2 . To adjus t the hour, pres s either button [1] or [2]  
while holding the [DISP] button down.  
Button [1]: Turns the hour back.  
Button [2]: Turns the hour forward.  
3 . To adjust the minutes, press either button [3] or [4]  
while holding the [DISP] button down.  
Button [3]: Turns the minutes back.  
Button [4]: Turns the minutes forward.  
To set the clock to 0 minutes, 0 seconds (an exact hour),  
press button [5], while holding down the [DISP] button.  
For example:  
At 3:23: Pressing button [5] returns to 3:00.  
At 3:32: Pressing button [5] advances to 4:00.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic operation  
ٕ
Switching audio control modes  
Various audio control modes may be fine-tuned using this  
procedure.  
1 . Press the [AUDIO CONTROL] button for less than  
one second.  
Pressing the button repeatedly will allow you to control  
adjustments of [BASS] (low frequencies), [TREB] (high  
frequencies), [FADER] (front-rear speaker balance),  
[BAL] (left-right speaker balance), and [SUB-W]  
(subwoofer level).  
2 . Turn the [AUDIO CONTROL] button to the left or  
right  
It controls levels and adjust the sound to your  
preference.  
When Tone Control Cancel feature is on, adjustment of  
BASS and TREB will be skipped.  
When an optional DSP/EQ unit is connected, the mode  
switches from Volume DSP level adjustment EQ level  
adjustment. BASS, TREB, BAL, FADER, may be skipped,  
and it depends on the type of DSP/EQ and its situation.  
ٕ
Enabling the loudness control  
The loudness control may be turned on to emphasize low  
and high frequencies at low volume levels.  
Loudness compensates for the apparent weakness of low  
and high frequencies at low volume by boosting the bass  
and treble levels.  
1. Press and hold the [AUDIO CONTROL] button until  
the [LOUD ON] display appears on the screen.  
To disable the loudness feature, repeat the above  
procedure to display the [LOUD OFF] indication.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic operation  
[E-COM] button  
[DISP] button  
Button [5]  
[FUNC] button  
[ASM] button  
ٕ
Switching Non-Fader modes  
1 . Press the [FUNC] button.  
2 . Press button [5] to switch the phase.  
3 . Press the [FUNC] button.  
Pressing the button will cancel Function mode.  
ٕ
Disabling the Tone Control Cancel feature  
1 . Press the [FUNC] button.  
2 . Press the [ASM] button to switch on or off.  
3 . Press the [FUNC] button.  
Pressing the button will cancel Function mode.  
ٕ
Disabling the display  
1 . Press the [FUNC] button.  
2 . Press the [DISP] button.  
Pressing the button will switch the display on or off.  
ٕ
Enabling E-COM feature  
1 . Press the [E-COM] button for one second.  
Pressing the button will switch the E-COM feature on or  
off.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the CD player  
[CD] button  
ٟ
How to operate the CD player  
First press the [CD] button to switch to the disc mode. It is  
assumed here that a CD has already been loaded into the  
unit.  
ع
Listening to CDs  
1 . Press the [CD] button.  
This turns on the disc mode and starts CD play.  
If an external CD changer is connected, each additional  
tap of the button will switch modes from CD changer  
1
CD changer 2 CD player.  
A changer or player with no discs loaded will be  
skipped.  
٨
٨
Caution  
Playback may be intermittent when there is a scratch on a  
CD or when the recorded side is dirty.  
Only two external CD changers may be connected.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the CD player  
Button [4]  
[
] buttons  
ع
Advancing to the next track or returning to  
the beginning of the track being played  
1 . Press the [  
] button.  
[
[
] button: Advances to the next track.  
] button: Returns to the beginning of the track being  
played.  
Pressing and holding the [ ] button will fast-forward  
through a track, while pressing the [ ] button will fast-  
reverse.  
ع
Playing the beginning of tracks (SCAN)  
1 . Press button [4 (SCAN)].  
Tapping the button causes the player to move up to  
the next track and play it for 10 seconds, then move  
up to the next track and play it for 10 seconds, and so  
on until the button is tapped again.  
To continue playing a desired track, press the button again  
to stop scanning.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the CD player  
[DISP] button  
Buttons [5] to [6]  
ع
ع
Repeating the same track (REPEAT)  
1 . Press button [5 (RPT)] to repeat the track being  
played.  
To cancel, press button [5] again.  
Playing tracks in random order (RANDOM)  
1 . Press button [6 (RAND)] to play the tracks in  
random order.  
To cancel, press button [6] again.  
Occasionally the same track happens to be played  
(selected) two or more times in a row; this is normal  
operation and is no sign of a problem.  
ع
Switching the display  
1 . Press the [DISP] button for less than one  
second.  
Each press of the button switches the display from the  
title the clock.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the CD player  
[ EJECT] button  
ع
Ejecting the disc  
1 . Press the [ EJECT] button.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the CD player  
[DISP]button  
Button [1]  
ع
Displaying a genre for a CDs  
A preset genre can be assigned to individual CD and  
displayed when they are played.  
1 . Press the [DISP] button until a preset genre is  
displayed.  
2 . Press button [1]  
Nine genre are available for a CD in the following  
sequence;  
1.JAZZ  
2.POPS  
3.ROCK  
4.FUSION  
5.BALLAD  
6.GUEST  
7.FAVORITE  
8.BRANDNEW  
9.DELETE  
When the [DELETE] is selected, the genre will not be  
displayed.  
ع
Switching the display  
1 .Press the [DISP] button for less than one  
second.  
Each press of the button switches the display from the  
title genre the clock.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the tuner  
[FMAM] button  
[
] buttons  
ٟ
How to operate the tuner  
First, press the [FMAM] button to start tuner operation.  
There are automatic and manual methods for setting stations  
in memory. The receiver will accept up to 24 stations in  
memory: six in AM and 18 in FM (6 each for FM1, FM2 and  
FM3.)  
ع
Tuning to a station  
1 . Tap the [FMAM] button to switch to the  
desired FM or AM mode.  
Each tap will switch modes from FM1 FM2 FM3 →  
AM.  
2 . Press the [  
] button to tune to a station.  
Tap the [ ] or [ ] button for less than one second to  
tune to a station manually.  
To start searching for a station automatically, hold the  
button down for more than one second.  
[
[
] button: Tunes to higher frequencies.  
] button: Tunes to lower frequencies.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the tuner  
[ASM] button  
[FMAM] button  
At times, it may be difficult to maintain optimum reception  
because the antenna affixed to your vehicle is in motion  
constantly (relative to the broadcast antenna), encountering  
continuous variation in the received radio signalsstrength.  
Other factors affecting reception include interference from  
natural obstacles, sign posts, etc.  
ع
Entering stations into memory automatically  
(The automatic preset mode: ASM)  
1 . Tap the [FMAM] button to switch to the  
desired FM or AM mode.  
Each tap switches modes from FM1 FM2 FM3 →  
AM.  
2 . Press the [ASM] button for more than two  
seconds until a beep is heard.  
The automatic preset mode starts.  
The [ASM] indicator on the screen flashes, and stations  
are automatically entered in memory under buttons [1]  
to [6].  
These buttons are called preset buttons.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the tuner  
[FMAM] button  
Buttons [1] to [6]  
[
] buttons  
Press any numbered button to select the station whose  
frequency is indicated right above the button.  
When a new station is set in memory, the station previously  
set in memory will be deleted.  
If the number of receivable stations fewer than six, the  
stations set in the rest of the preset buttons will be retained.  
ع
Manually setting stations into memory  
This section covers the setting of stations in memory under  
the numbered buttons.  
1 . Press the [FMAM] button to switch between  
FM and AM.  
2 . Use the [  
] button to tune to the station to  
be entered in memory.  
3 . Select any button, from [1] to [6], and press it  
for more than two seconds.  
The tuned station is now memorized and set in the  
button selected. Repeat the procedure to set additional  
manually tuned stations in memory, in turn, for buttons  
[1] to [6]. These buttons are called the preset buttons.  
٨
٨
Caution  
If the vehicles battery is disconnected (for repairs to the  
vehicle or for removing the receiver), all stations in memory  
will be lost. In such a case, set stations in memory again.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the tuner  
[ASM] button  
[DISP] button  
ع
Preset station scan  
This function enables reception of all the stations in the  
numbered preset buttons for five seconds each.  
1 . Press the [ASM] button.  
[PSCAN] will appear at the top of the display, and  
stations stored under preset buttons [1] through [6] will  
beplayed for five seconds each.  
2 . To stop the scan mode at a desired station,  
press the [ASM] button again.  
The receiver will stay tuned to the desired station.  
ع
Switching the display  
1 . Press the [DISP] button for less than one  
second.  
Each press of the button switches the display between  
the clock and current frequency.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the tuner  
ع
FM reception characteristics  
In general, FM has much better tonal quality than AM.  
However, FM and FM stereo reception encounter several  
characteristic problems not encountered with AM. FM is  
more difficult to receive than AM in a moving vehicle. The  
following are explanatory notes on what to expect from FM  
reception and on how to get satisfactory performance.  
1 . FM RECEPTION DIFFERS FROM AM  
A characteristic of transmitted signals is that lower  
frequencies travel further. FM frequencies are much  
higher than AMs (similar to a ray of light): they wont  
bend but they will reflect. Often, they will be interrupted  
by tall buildings, mountains, etc., taking direct and  
indirect paths to your vehicles antenna. The distance at  
which FM stations can be received satisfactorily is  
usually not nearly as far as that which AM stations can  
be received.  
AM Radio Waves  
Ionosphere  
FM Radio Waves  
Ionosphere  
2 . FADING OUT  
In weak signal or fringereception areas, FM stations  
may fade out completely, or fade in and out. When  
driving in weak signal areas, such as near hills, through  
valleys or tunnels, among tall buildings, etc., you may  
encounter unusual noise interference. THIS IS NOT A  
TUNER PROBLEM. In this case, you can only wait until  
you are in a better reception area, tune to a stronger  
station, or reduce the treble level.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the tuner  
3 . RECEPTION AREA OF FM BROADCASTS  
A home receiver can catch weak FM stereo signals  
through the use of a tall, directional or ultra-sensitive  
antenna. In a moving vehicle, the area for good  
reception is limited because of varying conditions  
encountered while driving, including the types and  
heights of broadcast antenna structures, signal  
strength, engine noise, etc. For best reception with  
manual antennae, extend the antenna mast as far as  
possible.  
Transmitting Antenna 100 Meters High  
Effective Radiation Power 1kW  
FM Stereo Auto Radio 20 km  
FM Monaural Auto Radio 50 km  
Home FM Stereo Receiver 100 km  
Reception quality varies depending on the power of the FM  
station, natural and artificial barriers,weather conditions, etc.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the tuner  
4 . MULTIPATH  
The reflection characteristics of FM waves cause  
another problem called multipathFM wave signals  
reflecting off of buildings, mountains, etc. When the  
antenna receives direct and reflected waves at the same  
time, distortion of sound in the treble range often  
occurs, such as static or a harsh-sounding voices. THIS  
IS NOT A TUNER PROBLEM. Only moving to another  
area with a clearer signal path can remedy the situation.  
DIRECT  
WAVE  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to use the Card remote control  
ٟ
How to use the Card remote  
control  
Precautions in use of the remote control  
• Be careful when handling the control, especially because it is  
small and light. Dropping or striking it hard may damage it,  
wear out the battery or cause a malfunction.  
• Keep the remote control free of moisture, dust and water. Do  
not subject it to shock.  
• Do not place the remote control unit where it will get hot,  
such as on the dashboard or near a heater vent. Allowing the  
remote control unit to overheat may warp its case or cause  
other problems.  
• Do not operate the remote control unit while driving because  
doing so could cause an accident.  
• When using the remote control,point it directry at the remote  
control light receptor.  
• The light receptor may not operate correctly if it is exposed to  
bright light such as direct sunlight.  
• Be sure to press the [PWR] button on the main unit to shut it  
down before leaving the car, or the car battery may be run  
down. When the main unit is shut down, the remote control  
will not work.  
• Remove the batteries from the remote control unit whenever  
it is not to be used for a long time.  
Cleaning the remote control  
• Use a dry cloth to keep the unit clean, If the remote control  
unit gets extremely dirty, clean it with a cloth moistened in  
dilute liquid detergent. Do not use alcohol or thinner; these  
compounds may damage the finish.  
• In no event should benzine or thinner be used. These  
substances will damage the case or finish.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to use the Card remote control  
[MODE] button  
[PWR]  
button  
Remote-control  
light receptor  
[+] button  
[-] button  
[MUTE]  
button  
ع
ع
Turning the power on/off  
1 . Press the [PWR] button.  
The power turns on or off each time the button is pressed.  
When the main unit is shut down, the remote control will  
not work.  
Adjusting the audio volume  
1 . Press the [+] or [-] button.  
[+] button: Increases the volume.  
[ -] button: Decreases the volume.  
ٕ
Cutting the volume instantly (muting):  
Press the [MUTE] button for more than two seconds to cut  
the volume or restore it instantly.  
ع
Switching playback modes  
1 . Press the [MODE] button.  
Tap the button to switch modes in the following  
sequence:  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to use the Card remote control  
[
] button  
BAND  
[
] buttons  
] buttons  
TUNESEEK  
[
PRESET CH  
ع
How to play the tuner  
Enter the tuner mode first.  
ٕ
Select the FM/AM band  
1. Tap the [BAND] button.  
Each tap will switch tuner modes from FM1 FM2 →  
FM3 AM.  
ٕ
Select a station (manually or automatically)  
A short tap of the button will allow manual station tuning.  
Pressing for more than one second will start automatic  
tuning.  
1. Press the [ TUNE• SEEK ] button.  
[
[
] button: Tunes to higher frequency stations.  
] button: Tunes to lower frequency stations.  
ٕ
Selecting preset stations  
A total of six stations may be selected (preset tuning) out of  
those already set in memory through the main unit. (Refer to  
Manually setting stations into memory,page 33.)  
1. Press the [ PRESET CH ] button.  
[
[
]
]
button: Selects the next higher number preset button.  
button: Selects the next lower number preset button.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to use the Card remote control  
[
] button  
BAND  
[
] buttons  
TRACKAPS  
[
] buttons  
DISC  
ع
How to play CDs  
Select the disc mode first.  
ٕ
Advancing to the next track or returning  
to the beginning of the track being played  
1. Press the [ TRACKAPS ] button.  
[
[
] button: Skips to the next track.  
] button: Returns to the beginning of the track being  
played.  
Hold the [ ] button down to fast-forward, or the [  
]
button to fast-reverse the track being played.  
ٕ
Skipping to the next or previous CD.  
1. Press the [ DISC ] button.  
[
[
] button: Selects the next higher number disc.  
] button: Selects the next lower number disc.  
ٕ
Switching disc modes  
1. Press the [BAND] button.  
When one or two CD changer is connected, tap the  
[BAND] button to change modes from CD player CD  
changer 1 CD changer 2.  
The indicator will skip a changer or player that has no  
discs loaded in it.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to use the Card remote control  
ع
Replacing the battery  
Warning  
To prevent accidents, store the batteries out of the reach  
of children. If a child has swallowed one, consult a doctor  
immediately.  
Use one CR2025 battery.  
1 . On the b a c k o f the re m o te c o ntro l, while  
pressing the locking knob on the battery slot  
cover toward your right, pull out the battery  
carier with your fingernail.  
UNLOCK  
2 . Remove the old battery, then place the new  
one in the carrier with the (+) mark facing up.  
3 . Push in the carrier until it snaps into place.  
Caution ●  
Be extremely careful not to swallow the battery.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to use an optional NOB remote control  
[AUDIO  
CONTROL]  
button  
Remote-control  
light receptor  
[PWR] button  
[MUTE] button  
ٟ
How to use an optional NOB  
remote control  
ع
ع
Turning the power on/off  
1 . Press the [PWR] button.  
The power turns on or off each time the button is pressed.  
When the main unit is shut down, the remote control will  
not work.  
Adjusting the audio volume  
1 . Press the [AUDIO CONTROL] button, and turn  
it to the left or right.  
Turn to the right: Increases the volume.  
Turn to the left : Decreases the volume.  
ٕ
Cutting the volume instantly (muting):  
Press the [MUTE] button for more than two seconds to cut  
the volume or restore it instantly.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to use an optional NOB remote control  
BAND  
MODE  
[BAND] button  
TUNE SEEK ] buttons  
[MODE] button  
ޓ
 
TRACK  
.
TUNE SEEK  
[
DISC  
E-COM  
MUTE  
PWR  
ILLUMI  
ع
ع
Switching playback modes  
1 . Press the [MODE] button.  
Tap the button to switch modes in the following  
sequence:  
How to play the tuner  
Enter the tuner mode first.  
ٕ
Select the FM/AM band  
1. Tap the [BAND] button.  
Each tap will switch tuner modes from FM1 FM2 →  
FM3 AM.  
ٕ
Select a station (manually or automatically)  
A short tap of the button will allow manual station tuning.  
Pressing for more than a second will start automatic tuning.  
1. Press the [ TUNESEEK ] button.  
[
[
] button: Tunes to higher frequency stations.  
] button: Tunes to lower frequency stations.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to use an optional NOB remote control  
BAND  
MODE  
ޓ
 
TRACK  
TUNE SEEK  
[
TRACK ] buttons  
DISC  
[
DISC ] buttons  
E-COM  
MUTE  
PWR  
ILLUMI  
ٕ
Selecting preset stations  
A total of six stations may be selected (preset tuning) out of  
those already set in memory through the main unit. (Refer to  
Manually setting stations into memory,page 33.)  
1. Press the [ DISC ] button.  
[
[
]
]
button: Tunes the next preset number at a higher frequency.  
button: Tunes the next preset number at a lower frequency.  
ع
How to play CDs  
Select the disc mode first.  
ٕ
Advancing to the next track or returning  
to the beginning of the track being played  
1. Press the [ TRACK ] button.  
[
[
] button: Skips to the next track.  
] button: Returns to the beginning of the track being  
played.  
Hold the [ ] button down to fast-forward, or the [  
]
button to fast-reverse the track being played.  
ٕ
Skipping to the next disc or back to the  
beginning of track being played.  
1. Press the[ DISC ] button.  
[
] button: Advances the disc number to that of the  
upper (next) disc.  
[
] button: Returns the disc number to that of the lower  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to use an optional NOB remote control  
(previous) disc.  
[BAND] button  
[E-COM] button  
BAND  
MODE  
ޓ
 
TRACK  
TUNE SEEK  
DISC  
E-COM  
MUTE  
PWR  
[ILLUMI] button  
ILLUMI  
ٕ
Switching disc modes  
1. Press the [BAND] button.  
When the CD changer is connected, tap the [BAND]  
button to change modes from CD player CD changer  
1 CD changer 2.  
The indicator will skip a changer or player that has no  
disc loaded in it.  
ع
ع
Illuminating the NOB remote control  
The buttons of the NOB remote control will be illuminated by  
pressing the [ILLUMI] button.  
Enabling the optional E-COM feature  
Pressing the [E-COM] button for one second will switch the  
E-COM feature on or off.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to use an optional NOB remote control  
ع
Replacing the battery  
Warning  
To prevent accidents, store the batteries out of the reach  
of children. If a child has swallowed one, consult a doctor  
immediately.  
Use two AA cell batteries.  
1 . Remove the back cover of the remote control  
unit by gently pres s ing and s liding it in the  
direction indicated by the arrow.  
2 . Install the two batterles provided into the  
compartment as illustrated inside the  
compartment.  
3 . Return the back cover into place by sliding it in  
the direction indicated by the arrow.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to use an optional NOB remote control  
Caution ●  
Be extremely careful not to swallow the battery.  
The battery life is approximately one year. If the  
remote control unit does not operate correctly or if  
the button lump gets dim, replace the batteries.  
Be sure to orlent the batteries correctly so that the  
positive and negative poles match the diagram.  
Do not use one new battery and one old one; use  
two new batteries..  
Use only two of the same kind of battery.  
If any liquid is seen leaking from the batteries,remove  
both batterles and dispose of them properly.  
Thoroughly clean the battery compartment with a  
dry cloth. Then install new batterles.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the receiver with an optional CD changer connected  
[CD] button  
[
] buttons  
ٟ
How to operate the receiver with an  
optional CD changer connected  
ع
Basic operation  
This section covers the operation of the CD changer that is  
connected to the receiver.  
To switch from another mode, press the [CD] button.  
ٕ
Listening to a CD  
1. Press the [CD] button  
Each press of the button switches the mode from CD  
Player CD Changer 1 CD Changer 2.  
ٕ
Advancing to the next track or returning  
to the beginning of the track being played  
1. Press the [  
] button.  
[
[
] button: Advances to the next track.  
] button: Returns to the beginning of the track being  
played.  
Hold down the [ ] button to fast-forward, or the [  
]
button to fast-reverse within the disc being played.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the receiver with an optional CD changer connected  
Buttons [4] to [6]  
ٕ
Playing the beginning of tracks (SCAN):  
1. Press button [4 (SCAN)].  
Tapping the button causes the changer to move up to  
the next track and play it for 10 seconds, then move up  
to the next track and play it for 10 seconds, and so on,  
on one CD, until the button is tapped again.  
Hold the button until the [ALL SCAN] display appears  
to play the first 10 seconds of the first track of every CD  
loaded.  
ٕ
ٕ
Repeating the same track (REPEAT):  
1. Press button [5 (RPT)].  
Tapping on the button causes the changer to repeat  
the track currently being played, until the button is  
tapped again.  
Hold the button until the [ALL REPEAT] display appears  
to repeat all tracks on the CD being played.  
Playing tracks in random order (RANDOM):  
1. Press button [6 (RAND)].  
Tapping on the button causes the changer to play the  
tracks on the currently playing CD in random order.  
Hold the button until the [ALL RANDOM] display  
appears to play tracks from all of the CDs (loaded in  
the currently selected changer) in random order.  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the receiver with an optional CD changer connected  
[ASM] button  
Buttons [1] to [6]  
[
] buttons  
DISC  
Occasionally the same track happens to be played  
(selected) two or more times in a row, but it is no sign of  
a problem.  
When any of the functions - Playing the beginning of  
tracks,” “Repeating the same trackand Playing tracks  
in random order- is selected, a message such as  
[SCAN], [ALL-SCAN], [RPT], [ALL-RPT], [RAND] or [ALL-  
RND] is displayed at the bottom of the screen to verify  
the current function.  
ٕ
ٕ
Skipping to the next or previous CD  
1. Press either button [  
].  
] button: Selects the next higher number disc.  
button Selects the next lower number disc  
DISC  
[
[
]
:
.
Specifying a CD to play  
A CD of your choice is directly selectable out of the loaded  
discs.  
1. Press the [ASM] button.  
2. Press a button from [1] to [6].  
Buttons  
CDs*  
1
1
7
2
2
8
3
3
9
4
4
5
5
6
6
10 11 12  
To select a CD from no. 7 to 12, press the  
desired button considerably longer.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the receiver with an optional CD changer connected  
[DISP] button  
Button[1]  
ع
Displaying a genre for a CDs  
A preset genre can be assigned to individual CD and  
displayed when they are played.  
1 . Press the [DISP] button until a preset genre is  
displayed.  
2 . Press button [1]  
Nine genre are available for a CD in the following  
sequence;  
1.JAZZ  
2.POPS  
3.ROCK  
4.FUSION  
5.BALLAD  
6.GUEST  
7.FAVORITE  
8.BRANDNEW  
9.DELETE  
When the [DELETE] is selected, the genre will not be  
displayed.  
ع
Switching the display  
1 .Press the [DISP] button for less than one  
second.  
Each press of the button switches the display from the  
title genre the clock.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the receiver with an optional DSP/EQ unit connected  
Button [1]  
[FUNC] button  
ٟ
How to operate the receiver with  
an optional DSP/EQ unit connected  
ع
How to operate the DSP functions  
The DSP feature adds reverberations to simulate ambience in  
different types of surroundings (room sizes).  
1 . After pressing the [FUNC] button, tap button  
[1].  
Each tap of the button [1] will switch the room size.  
ٕ
Switching room sizes.  
1. Tap button [1] to switch room sizes.  
Six room sizes are available for selection in the  
following sequence:  
1. CONCERT (a concert hall)  
2. LIVE (a live house)  
3. CATHEDRAL (a church with rich reverberations)  
4. STADIUM (an outdoor stadium)  
5. CLUB  
6. DEFEAT (DSP OFF)  
2. Push the [FUNC] button.  
This cancels the adjustment mode; the selected room  
size will now take effect.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the receiver with an optional DSP/EQ unit connected  
Button [1]  
[FUNC] button  
The following six patterns are preset at the factory:  
Button  
Indicator display  
CONCERT  
LIVE  
1
2
3
4
5
6
CATHEDRAL  
STADIUM  
CLUB  
CONCERT  
ٕ
Fine-tuning an individual roomsize mode  
Detailed adjustments are available in any of the room size  
modes.  
1. After pres s ing the [FUNC] button, hold button [1]  
down for more than a second.  
The DSP mode starts.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the receiver with an optional DSP/EQ unit connected  
[AUDIO CONTROL] button  
Buttons [1] to [6]  
2. Tap button [AUDIO CONTROL] to select the desired  
mode of adjustment.  
The mode sequence on the button is as follows:  
Level Duration value  
(Reverberation level)*  
(Reverberation duration)*  
(Initial echo level)  
○○○  
○○○  
LR  
LR  
ER  
ER  
dB  
S
○○○  
○○○  
dB  
(Initial echo delay)  
mS  
The level and duration adjustments are available  
in CONCERT and CATHEDRAL modes only.  
*
3. Turn the [AUDIO CONTROL] button.  
This button adjusts the reverberation level and duration.  
Right: Increases the value.  
Left: Decreases the value.  
4. Hold down a button, [1] to [6], for more than two  
seconds to preset a value.  
The preset value is overwritten by the value set using  
the above steps.  
Direct (original sound)  
Reverberation duration  
High  
Initial echo]  
Level  
Time  
Long  
Initial echo delay Reverberation  
55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the receiver with an optional DSP/EQ unit connected  
Buttons [1] to [6]  
[FUNC] button  
5. Push the [FUNC] button.  
The adjustment mode will be canceled and the  
selected room size will now take effect.  
ٕ
Retrieving a preset pattern from memory  
Press a preset button to retrieve the room size in memory.  
The buttons under which room sizes are stored in memory  
are called preset buttons.  
1. After pres s ing the [FUNC] button, hold button [1]  
down for more than one second.  
2. Press a button, [1] to [6].  
The room size, as preset in the button, is retrieved.  
3. P re s s th e [FUNC] b u tto n to c a n c e l th e DS P  
adjustment mode  
.
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the receiver with an optional DSP/EQ unit connected  
Button [2]  
[FUNC] button  
ع
How to operate the EQ functions  
The EQ functions enable level adjustments of various  
frequency groups for optimum listening conditions with a  
specific kind of music or musical instrument.  
ٕ
Switching equalizer modes  
1. After pressing the [FUNC] button, tap button [2] to  
switch equalizer modes.  
Six kinds of music categories are available for selection  
in the following sequence:  
1. POPS  
2. ROCK  
3. JAZZ  
4. CLASSICAL  
5. VOCAL  
6. NEWS  
7. DEFEAT EQ OFF)  
2. Push the [FUNC] button  
.
The adjustment mode will be canceled and the  
selected equalizer mode will now take effect.  
The initial EQ settings are factory preset.  
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the receiver with an optional DSP/EQ unit connected  
[AUDIO CONTROL] button  
Buttons [1] to [6]  
[FUNC] button  
ٕ
Fine-tuning EQ functions  
1. After pres s ing the [FUNC] button, hold button [2]  
down for more than one second.  
The EQ adjustment mode starts.  
2. Tap button [2] until the desired equalizer mode is  
displayed.  
3. Tap the [AUDIO CONTROL] button to switch  
frequencies.  
The frequencies will switch in the following sequence:  
63Hz 125Hz 250Hz 500Hz 1kHz 4kHz 12.5kHz  
4. Turn the [AUDIO CONTROL] button to adjust the level.  
Right :Increases the value.  
Left :Decreases the value.  
5. Hold down a button, [1] to [6], for more tha n two  
seconds to preset a value.  
The preset value is overwritten by the value set using  
the above steps.  
6. Push the [FUNC] button  
.
This cancels the adjustment mode. The selected value  
will now take effect.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to operate the receiver with an optional DSP/EQ unit connected  
Buttons [1] to [6]  
[FUNC] button  
ٕ
Retrieving an equalizer mode from memory  
Press a preset button to retrieve the equalizer mode set in  
memory for the button.  
The buttons that set equalizer modes in memory are called  
preset buttons.  
1. After pres s ing the [FUNC] button, hold button [2]  
down for more than one second.  
2. Press a button, [1] to [6]  
.
3. Press the [FUNC] button.  
The selected equalizer mode will now take effect, and  
the EQ adjustment mode will be canceled.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If you have a question:  
[Reset] button  
ٟ
If you have a question:  
First check the items mentioned below before attempting to  
troubleshoot problems.  
٨
٨
Caution  
If a problem occurs, for instance when the unit does not  
respond to any button presses, or the display doesn't  
work press the reset button using a sharp tool.  
Pressing the reset button will delete all the entries from  
memory. The settings will return to those made at the  
factory prior to shipment.  
A CD that has been loaded will be ejected. Open the front  
panel and remove the ejected CD.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If you have a question:  
ع
Displaying information  
(for troubleshooting)  
The information listed in the chart below is displayed to show  
the status of the CD player and CD changer. Refer to the  
chart for the appropriate action.  
Infomation Code Table  
When INFO flash on the  
indicator .  
Nos.2-7 are displayed.  
Infomation Contents  
2 NO DISK LOADED IN  
THE MAGAZINE  
Explanation and remedial action to take.  
There is no disc in the magazine or player.  
Load adisc in the magazine.  
Load a music disc.)�  
The loaded disc is dirty or upside down.  
3 DISCS ARE DIRTY OR  
DAMAGED  
Check it for proper orientation and verity it  
is clean.  
The CD changer is inoperative for some  
reason.Go through the magazine removal  
procedure.  
CD CHANGER FAILS  
MECHANICALLY  
5
If a magazine fails to eject, have your dealer  
fix the problem.  
The temperature in the CD changer is too  
high for operation.Wait until it cools down.  
Resume playing after the High  
temperature sensed and CD stopped ”�  
display disappears.If the CD still cannot  
play , have your dealer repair it.  
6 WHEN THE CD CHANGER  
INTERNAL TEMPERATURE  
IS HIGH. TO PROTECT  
PLOKUP UNIT)�  
7 AN INTERNAL POWER Tum the ACC off once before turning it on  
SUPPLY FAILURE IS  
OCCURRING WITH THE  
AUTO CHANGER  
once again to resumu the operation.  
If the function still cannot be resctred,  
ccntact your dealer.  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If you have a question:  
Remedial action Refer  
to take to page  
Mode  
Common Dead or  
to all weak sound  
Problem  
Causes  
Is the volume control up sufficiently? Turn up the volume control. 21  
Is the muting function in effect  
(MUTE)?  
Cancel the muting  
(MUTE) function.  
21  
24  
Is the fader or balance control set  
far to one side?  
Readjust the fader and  
balance controls to more  
normal positions.  
Other probable causes include  
broken audio-signal wiring or a  
faulty speaker.  
Have your dealer check  
the problem.  
Power does Are too many electrical items  
Have your dealer check  
not turn on. installed, causing a lack of power? the problem.  
Other probable causes include a  
run-down car battery, broken  
power or interconnection wiring.  
Have your dealer check  
the problem.  
32  
33  
53  
Frequencies Has the car battery been disconnected Reenter them into  
or titles set in for repair or checked out?  
memory are  
memory.  
deleted.  
Are too many electrical items  
installed and causing lack of  
available power?.  
Have your dealer check  
the problem.  
Other probable causes include run- Have your dealer check  
down car battery, broken power or the problem.  
interconnection wiring.  
No guide  
tone sounds.  
Is the guide tone disabled?  
Is the battery low?  
Enable the guide tone.  
Replace battery.  
22  
42  
47  
The remote  
control does  
not work.  
42  
47  
Is the battery installed in reverse  
polarity?  
Reinstall the battery in  
the correct polarity.  
Is direct sunlight hitting the remote Use the remote control  
39  
43  
control light receptor?  
close to the receptor.  
Other probable causes include a  
malfunctioning remote control.  
Have your dealer check  
the problem.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If you have a question:  
Remedial action Refer  
Mode  
Problem  
Causes  
to take  
to page  
CD The disc cannot be inserted. Is an extra label or seal  
The disc is ejected as soon applied to the disc?  
as it is inserted.  
Do not apply labels or seals  
to the disc.  
9
Or, the disc cannot be  
ejected.  
The disc cannot be  
changed.  
Are there rough edges,  
deformations or  
damaged areas on the  
disc?  
Try inserting another disc.  
Removed any burrs. Do  
not use a deformed or  
damaged disc.  
10  
Sound skips around.  
Sound is intermittent.  
Sound is bad in quality.  
Is the disc damaged?  
Try another disc. Do not  
9
(scratched, warped, etc.) play a damaged disc.  
Is the disc clean? Clean the disc.  
Is the player mounted at Have your dealer check it  
11  
a proper angle?  
Is the player mounted  
loosely?  
out.  
Are you driving over a  
rough surface?  
Avoid playback while  
driving over rough surfaces.  
8
Problem  
Causes  
Remedial action to take  
Extend the antenna.  
Receives no  
stations, or  
receives static  
noise.  
Is the antenna retracted?  
Is the tuner correctly tuned to a  
station?  
Tune to a station.  
31  
Are you driving outside the service  
area of your preset stations?  
Tune to a local station.  
(Please note, there may be  
no local stations servicing  
the area where you are  
currently driving.)  
31  
Are you operating other equipment  
with a computer, or a mobile phone,  
in your vehicle at the same time as  
your receiver?  
Avoid operating such  
equipment while using the  
receiver.  
Other problems may include a loose  
or disconnected antenna cable, a  
bad antenna cable or a bad antenna  
Have your dealer retailer  
check the problem.  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
ٟ
Specifications  
<GENERAL>  
Power Supply  
Current Drain  
14.4VDC (11-16V)  
3A (1W)  
Dimensions (W x H x D)  
In-Dash Unit  
7×2×6-1/8(178×50×155mm)  
<FM TUNER>  
Frequency Range  
Usable Sensitivity  
87.75~107.9MHz (200KHz step)  
13dBf  
50dB Quieting Sensitivity  
Frequency Response  
Stereo Separation  
16dBf  
30~15,000H, ±3dB  
38dB (1KHz)  
<AM TUNER>  
Frequency Range  
Usable Sensitivity  
530~1,710KHz (10KHz step)  
18μV  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
<CD SECTION>  
Frequency Response  
Wow & Flutter  
Stereo Separation  
S/N Ratio (A-weighted)  
Dynamic Range  
20~20,000Hz  
Below measurable limits  
64dB  
94dB  
90dB  
Total Harmonic Distortion  
0.03% (1KHz)  
<AUDIO AMPLIFIER>  
Power Output  
20W×4 (20~20,000Hz,1.0% THD ,  
4Ω) MAX .40W×4  
Output Level/Impedance  
Tone Action  
2.7V (0dB) 330Ω line-out impedance  
Bass:±10dB at 100Hz  
Treble:±10dB at 10KHz  
+10dB at 100Hz /+6.5dB at 10KHz  
Loudness  
65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before Installation  
ٟ
Before Installation  
Notes  
Be sure to disconnect the battery negative terminal before  
installing the receiver.  
ع
Components  
No.  
Item  
Q'ty  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
Main unit  
Mounting sleeve  
Side bracket  
Rear bracket  
Bezel  
Bushing  
Self-tapping screw (6 x 16 mm)  
Stud bolt  
Flat head screw (5 x 8 mm)  
Hex-head bolt (5 x 20 mm)  
Hex nut (5 mm)  
Interconnecting cable  
Remote control  
1
1
2
1
1
1
2
1
4
2
2
1
1
ع
Setting the system-selector switch  
When this receiver is used in combination with an external  
amplifier, DSP, etc., the selector switch on the left side of  
the main unit may have to be switched.  
Set the switch according to the table below:  
External amplifier DSP/EQ/XOVER  
Switch  
None  
None  
Connected  
Connected  
None  
Off*  
On  
Off*  
Off*  
Connected  
Connected  
None  
:Pattern of selector switch at shipping  
MAIN UNIT LEFT SIDE VIEW  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting instruction  
ٟ
Mounting instruction  
ع
Mounting the main unit  
1 . Insert the mounting sleeve into the opening in  
the vehicle console.  
2 . Use a screwdriver or the like to bend the tabs in  
the mounting sleeve to secure the mounting  
sleeve.  
3 . Attach the side brackets to the main unit using  
flathead screws.  
MAIN UNIT  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting instruction  
4 . Mount the stud bolt to the main unit.  
5 . Insert the main unit into the mounting sleeve  
until it locks in place.  
6 .  
Fasten the rear of the main unit using either  
method [A] or [B].  
Select method [A] or [B] to suit the interior configuration  
of the vehicle.  
7 . Install the bezel on the main unit.  
[A]  
TOP  
[B]  
TOP  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting instruction  
Notes  
To prevent unconnected leads from shorting out, insulate  
them by wrapping their tips with electrical tape. Similarly,  
insulate the ends of connected leads.  
If an external amplifier is to be connected to the receiver,  
be sure to ground its outside housing to the vehicle body  
(a metal part).  
ع
Names of lead wires and destinations  
(refer to Page 71)  
No.  
1
Name  
Wire color  
Destination  
ACC  
Red  
Connect where the power comes on  
when the ignition is in the ACC  
position.  
2
B+  
Yellow  
Black  
Connect where the power is constantly  
available, regardless of the ignition  
switch's position.  
3
4
5
6
7
Ground  
Connect where good body grounding  
is available.  
Antenna power supply Blue  
Connect to the automatic-antenna  
control terminal of the vehicle.  
Lamp power supply  
Orange/White  
Connect to where power comes on  
when the headlights are turned on.  
Control power supply Blue/White  
E-LAN terminal  
Connect to the control terminal for the  
external amplifier, etc.  
Connect to the E-LAN terminal of the  
CD changer, DSP, etc.  
8 & 9 Line-in/out terminals  
Connect to the RCA input connectors  
of an external amplifier,or to the RCA  
output connectors of a DSP or EQ.  
10  
Line-out terminals (Nonfader)  
Connect to the RCA input connectors  
of a DSP or EQ, or the RCA connectors  
of a woofer amplifier.  
11  
12  
13  
14  
Speaker terminals  
Cellular phone mute  
Digital out terminal  
Connect them to their respective  
speakaers.  
Pink  
Connect the ground output terminal  
on a mobile phone.  
Connect to digital input terminal of the  
Eclipse Commander module.  
terminal  
Eclipse Commander  
Connect to the Eclipse Commander.  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting instruction  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting instruction  
ع
System  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting instruction  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting instruction  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting instruction  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Mounting instruction  
IMPORTANT  
RECORD YOUR KEY  
CD” HERE…  
STORE YOUR KEY CD”  
ALONG WITH YOUR  
OWNER’S MANUAL IN  
YOUR SOCK DRAWER.  
75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This device com plies w ith part 15  
of the FCC Rules. Operation is subject  
to the condition that this device  
does not cause harm ful interference.  
CUSTOMER NOTICE  
Please retain this booklet and write in the serial number of your 54420 for  
identification. The serial number is labeled or stamped on the chassis.  
Serial No.  
R
by FUJITSU TEN  
DIVISION OF FUJITSU TEN CORP. OF AMERICA  
19600 SOUTH VERMONT AVENUE, TORRANCE, CA 90502  
(310) 327-2151  
090001-13810700  
9912DE(N.O.)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Blower ES 230 User Manual
Eizo Computer Monitor LA 131 D User Manual
Electrolux Refrigerator 210621236 11052010 User Manual
Euro Pro Food Processor EP91W User Manual
Exakta Digital Camera EXA IIa User Manual
Faber Ventilation Hood Inca Pro 38 User Manual
Furuno Radar Detector FR 1410DS User Manual
Gardena Lawn Mower Art 4005 User Manual
GE Oxygen Equipment PT878 User Manual
Gitzo Camcorder Accessories G1227 User Manual