Echo Remote Starter EDR 210 User Manual

OPERATOR’S MANUAL  
ENGINE DRILL  
EDR-210  
WARNING  
READ INSTRUCTIONS CAREFULLY AND FOLLOW RULES FOR  
SAFE OPERATION.  
FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.  
ECHO, INCORPORATED  
400 Oakwood Road, Lake Zurich, Illinois 60047-1564  
Phone : 847-540-8400  
X750-004 57 6  
X750409-3506  
Printed in Japan 1305Bm 1507 ES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
ECHO Engine Drill EDR-210 is a lightweight, high  
performance, two-stroke engined unit designed for  
drilling.  
WARNING  
IMPROPER USE OR CARE OF THIS UNIT, OR  
FAILURE TO WEAR PROPER PROTECTION  
CAN RESULT IN SERIOUS INJURY.  
READ AND UNDERSTAND THE RULES FOR  
SAFE OPERATION AND ALL INSTRUCTIONS  
IN THIS MANUAL.  
This Manual provides the information necessary  
for operation and maintenance.  
SAFETY AND SPECIAL INFORMATION  
CIRCLE AND SLASH SYMBOL  
This symbol means the specific action  
shown is prohibited. Ignoring these  
prohibitions can result in serious or  
fatal injury.  
DANGER  
The safety alert symbol accompanied by the  
word “DANGER” calls attention to an act or  
condition which WILL lead to serious  
personal injury or death if not avoided.  
NOTE  
WARNING  
This enclosed message provides tips for use,  
care and maintenance of the unit.  
The safety alert symbol accompanied by the  
word “WARNING” calls attention to an act or  
condition which CAN lead to serious  
personal injury or death if not avoided.  
IMPORTANT  
The enclosed message provides information  
necessary for the protection of the unit.  
CAUTION  
Throughout this manual and on the product itself,  
you will find safety alters and helpful, information  
messages preceded by symbols or key words.  
The following is an explanation of those symbols  
and key words and what they mean to you.  
The safety alert symbol accompanied by the  
word “CAUTION” calls attention to an act or  
condition which may lead to minor or  
moderate personal injury if not avoided.  
DECALS AND SYMBOLS  
Symbol form/shape  
Symbol description/application  
Symbol form/shape  
Symbol description/application  
Carefully read the operator’s  
manual  
Wear eyes, ears and head  
protection  
Beware of high-temperature  
areas  
Finger severing  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY  
WARNING  
WARNING  
ENGINE DRILL USERS RISK INJURY TO  
THEMSELVES AND OTHERS IF THE ENGINE  
DRILL IS USED IMPROPERLY, AND/OR  
SAFETY PRECAUTIONS ARE NOT  
FOLLOWED. PROPER CLOTHING AND  
SAFETY GEAR MUST BE WORN WHEN  
OPERATING ENGINE DRILL.  
ALWAYS STOP THE ENGINE WHEN A DRILL  
JAM OCCURS. DO NOT ATTEMPT TO  
REMOVE AN OBJECT CAUSING A DRILL  
JAM IF THE ENGINE IS RUNNING. PHYSICAL  
INJURY CAN OCCUR IF A DRILL JAM IS  
REMOVED AND THE DRILLS START  
MOVING.  
Do all drilling at full throttle speed. Drilling at  
less at than full speed can damage the clutch  
by allowing it to slip.  
OPERATOR SAFETY  
Read this Engine drill Operator’s Manual  
carefully. Be sure you understand how to  
operate this unit properly before you use it.  
WARNING  
USE A FIRM GRIP WITH THUMBS AND  
FINGERS ENCIRCLING THE HANDLES. A  
FIRM GRIP WILL HELP YOU KEEP  
Be familiar with all the controls and the proper  
use of the machine.  
CONTROL OF THE ENGINE DRILL. NEVER  
OPERATE THE ENGINE DRILL ONLY ONE  
HAND OR BODILY INJURY CAN OCCUR.  
Wear proper clothing to protect legs and other  
exposed parts of your body.  
Wear non-skid sole shoes. Do not wear open-  
toed shoes or operate unit while bare footed.  
Always carry the engine drill with the engine  
stopped and the HOT muffler away from your  
body.  
Wear eye and hearing protection devices.  
Use caution when handling fuel. Put the caps  
back tightly on both the fuel can and the  
engine drill fuel tank.  
PROTECTIVE EQUIPMENT  
Always wear eye protection goggles that meet  
ANSI Z87.1 standards.  
Move at least 3 m (10 feet) from the re-fueling  
point and be sure there is no leakage of fuel  
from the fuel tank cap or the fuel system before  
starting the engine.  
Wear hearing protection.  
ECHO recommends that hearing protection be  
worn at all times.  
Operate this gasoline powered engine  
equipment in a well-ventilated area only.  
Dress properly! Do not wear loose clothing or  
jewellery, they can be caught in moving parts.  
Use of sturdy gloves, non-skid footwear, and  
safety glasses is recommended.  
Start the unit on the ground with the throttle set  
at idle. Do not start if the drills are obstructed  
by the ground or any other object.  
While operating the machine always be sure of  
a secure position.  
Never allow children to use the machine.  
Do not allow anyone to hold the material you  
are drilling.  
Keep a firm grip on the engine drill with both  
hands, one hand on the front handle, the other  
hand on the rear handle.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wear non-slip, heavy-duty work gloves to  
improve your grip on the engine drill handles.  
The gloves also help reduce the transmission  
of machine vibrations to your hands.  
WARNING  
PRECAUTION AGAINST VIBRATION  
AND COLD  
IT IS BELIEVED THAT A CONDITION  
CALLED RAYNAUD’S PHENOMENON,  
WHICH AFFECTS THE FINGERS OF  
CERTAIN INDIVIDUALS MAY BE BROUGHT  
ABOUT BY EXPOSURE TO VIBRATION AND  
COLD. EXPOSURE TO VIBRATION AND  
COLD MAY CAUSE TINGLING AND  
PROTECTING OTHERS  
Spectators, children, fellow workers and animals  
must be warned to come no nearer than 4.6 m (15  
feet) while the engine drill is in use.  
People working in the area near you should wear  
the same protective equipment as the operator.  
BURNING SENSATIONS FOLLOWED BY  
LOSS OF COLOR AND NUMBNESS IN THE  
FINGERS. THE FOLLOWING PRECAUTIONS  
ARE STRONGLY RECOMMENDED BECAUSE  
THE MINIMUM EXPOSURE WHICH MIGHT  
TRIGGER THE AILMENT IS UNKNOWN.  
PHYSICAL CONDITION  
Your judgement and dexterity may be impaired if  
you are ill or have taken alcohol or other  
substances known to affect the way you would  
normally function.  
• KEEP YOUR BODY WARM, ESPECIALLY  
THE HEAD, NECK, FEET, ANKLES, HANDS  
AND WRISTS.  
• MAINTAIN GOOD BLOOD CIRCULATION  
BY PERFORMING VIGOROUS ARM  
EXERCISES DURING FREQUENT WORK  
BREAKS AND ALSO BY NOT SMOKING.  
• LIMIT THE HOURS OF OPERATION. TRY  
TO FILL EACH DAY WITH JOBS WHERE  
OPERATING THE ENGINE DRILL OR  
OTHER HAND-HELD POWER EQUIPMENT  
IS NOT REQUIRED.  
• IF YOU EXPERIENCE DISCOMFORT,  
REDNESS AND SWELLING OF THE  
FINGERS FOLLOWED BY WHITENING AND  
LOSS OF FEELING, CONSULT YOUR  
PHYSICIAN BEFORE FURTHER EXPOSING  
YOURSELF TO COLD AND VIBRATION.  
ainful or numb fingers?  
ee your doctor  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Repetitive Stress Injuries  
It is believed that over-using the muscles and  
tendons of the fingers, hands, arms and shoulders  
may cause soreness, swelling, numbness,  
weakness and extreme pain in those areas.  
Certain repetitive hand activities may put you at a  
high risk for developing a Repetitive Stress Injury  
(RSI). An extreme RSI condition is Carpal Tunnel  
Syndrome (CTS), which could occur when your  
wrist swells and squeezes a vital nerve that runs  
through the area. Some believe that prolonged  
exposure to vibration may contribute to CTS.  
CTS can cause severe pain for months or even  
years. To reduce the risk of RSI/CTS, do the  
following:  
Avoid using your wrist in a bent, extended or  
twisted position. Instead try to maintain a  
straight wrist position. Also, when grasping,  
use your whole hand, not just the thumb  
and index finger.  
Take periodic breaks to minimize repetition  
and rest your hands.  
Reduce the speed and force with which you do  
the repetitive movement.  
Do exercise to strengthen the hand and arm  
muscles.  
See a doctor if you feel tingling, numbness or  
pain in the fingers, hands, wrists or arms.  
The sooner RSI/CTS is diagnosed, the more  
likely permanent nerve and muscle damage  
can be prevented.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING TECHNIQUES  
When starting to drill, run the engine at full  
throttle.  
When transporting or storing the machine  
always remove the drill bit.  
To reduce fire hazard keep engine and silencer  
free of debris, leaves or excessive grease.  
WARNING  
BEFORE DRILLING, BE SURE TO READ AND  
UNDERSTAND THE ENTIRE OPERATOR’S  
MANUAL TO AVOID THE CHANCE OF  
SERIOUS INJURY.  
Handle drill with care, contacting with drills  
may cause injury.  
Do not force the drills and only move as  
quickly as the drills will allow.  
Stop the engine and disconnect from ignition  
cable before: - cleaning or when clearing a  
blockage; checking, maintenance or working  
on the machine.  
Handle fuel with care; it is highly flammable.  
Never add fuel to a machine with a running or  
hot engine.  
Do not attempt to repair the machine unless  
you are qualified to do so.  
Do not operate the machine with a damaged or  
excessively worn drill bit.  
Always ensure all handles and guards are  
fitted when using the machine. Never attempt  
to use an incomplete machine or one fitted with  
an unauthorized modification.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
DESCRIPTION  
2
1
14  
15  
13  
Part Number X505-002570  
12  
11  
Part Number X505-002310  
10  
Part Number X505-002570  
9
7
6
8
5
* If a decal cannot be read, a new one can be  
ordered from your ECHO dealer.  
1. Operator’s manual - Included with unit. Read  
before operation and keep for future reference  
to learn proper, safe operating techniques.  
9. Fuel tank - Contains fuel and fuel filter.  
10. Fuel tank cap - For closing the fuel tank.  
11. Air cleaner cover - Covers air filter.  
2. Throttle trigger - Device activated by the  
operator’s finger, for controlling the engine  
speed.  
12. Starter handle - Pull handle to start the  
engine.  
13. Throttle trigger lockout - Device that  
3. Rear handle - Handle located furthest from the  
prevents the accidental operation of the throttle  
trigger until manually released.  
drill bit.  
4. Silencer cover  
5. Drill bit - Not included with unit.  
6. Chuck  
14. Ignition switch - Device for allowing the  
engine to be started and stopped.  
15. Spark plug  
7. Shift lever  
8. Front handle - Handle located on the front  
gear case.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLING  
FRONT HANDLE  
Insert the front handle to the machine, and turn  
clockwise.  
(TIGHTEN THE SCREW FIRMLY)  
- To operate front handle with right hand,  
remove right plug then reverse sides when  
installing handle and plug.  
Washer  
Fro
DRILL BIT  
Insert the drill bit (not provided with unit) until it  
reaches the bottom of the chuck, then back it  
out slightly; tighten the chuck laws evenly and  
completely.  
IMPORTANT  
Use drill bits suited for the material being  
drilled and for the depth of hole required.  
Plug  
Chuck  
Drill bit  
(Tighten three points evenly)  
OPERATION  
CHECK UP OF NUTS AND OTHER  
HARDWARES  
WARNING  
ALTERNATIVE FUELS, SUCH AS E-20 (20 %  
ETHANOL), E-85 (85 % ETHANOL) OR ANY  
FUELS NOT MEETING ABOVE  
Check up loose nuts, bolts and screws before  
using the unit every day.  
REQUIREMENTS ARE NOT APPROVED FOR  
USE IN ECHO 2-STROKE GASOLINE  
ENGINES.  
FUEL STATEMENT  
USE OF ALTERNATIVE FUELS MAY CAUSE  
PERFORMANCE PROBLEMS, LOSS OF  
POWER, OVERHEATING, FUEL VAPOR  
LOCK, AND UNINTENDED MACHINE  
OPERATION, INCLUDING, BUT NOT LIMITED  
TO, IMPROPER CLUTCH ENGAGEMENT.  
ALTERNATIVE FUELS MAY ALSO CAUSE  
PREMATURE DETERIORATION OF FUEL  
LINES, GASKETS, CARBURETOR AND  
OTHER ENGINE COMPONENTS.  
GASOLINE - Use 89 Octane [(R+M)/2] (mid grade  
or higher) gasoline or gasohol known to be good  
quality.  
Gasohol may contain up to 10 % Ethyl (grain)  
alcohol or 15 % MTBE (methyl tertiary-butyl ether).  
Gasohol containing methyl (wood) alcohol is NOT  
approved.  
TWO-STROKE OIL - A two-stroke engine oil meeting  
ISO-L-EGD (ISO/CD 13738) and JASO M345-FC/FD  
Standards must be used. ECHO brand premium  
Power Blend X™ Universal 2-Stroke Oil meets these  
standards. Engine problems due to inadequate  
lubrication caused by failure to use an ISO-L-EGD  
(ISO/CD 13738) and JASO M345-FC/FD certified oil,  
such as ECHO premium Power Blend X™, will void  
the two-stroke engine warranty. (Emission related  
parts only are covered for two years, regardless of  
two-stroke oil used, per the statement listed in the  
Emission Defect Warranty Explanation.)  
Fuel Mix Chart 50 : 1  
US.  
METRIC  
Gasoline  
Gasoline  
Gallons  
Oil  
Oil  
US. fl. oz.  
L
mL  
1
2
5
2.6  
5.2  
12.8  
4
8
20  
80  
160  
400  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT  
• ECHO premium Power Blend X™ Universal  
2-Stroke Oil may be mixed at 50 : 1 ratio for  
application in all ECHO engines sold in the  
past regardless of ratio specified in those  
manuals.  
• Use of unmixed, improperly mixed, or fuel  
older than 90 days, (stale fuel), may cause  
hard starting, poor performance, or severe  
engine damage and void the product  
warranty. Read and follow instructions in  
the Storage section of this manual.  
HANDLING FUEL  
MIXING INSTRUCTIONS -  
1. Fill an approved fuel container with half of the  
DANGER  
FUEL IS VERY FLAMMABLE. USE EXTREME  
CARE WHEN MIXING, STORING OR  
HANDLING OR SERIOUS PERSONAL  
INJURY MAY RESULT.  
• USE AN APPROVED FUEL CONTAINER.  
• DO NOT SMOKE NEAR FUEL.  
• DO NOT ALLOW FLAMES OR SPARKS  
NEAR FUEL.  
• FUEL TANKS/CANS MAY BE UNDER  
PRESSURE.  
ALWAYS LOOSEN FUEL CAPS SLOWLY  
ALLOWING PRESSURE TO EQUALIZE.  
• NEVER REFUEL A UNIT WHEN THE  
ENGINE IS HOT!  
required amount of gasoline.  
2. Add the proper amount of two-stroke oil to  
gasoline.  
3. Close container and shake to mix oil with  
gasoline.  
4. Add remaining gasoline, close fuel container,  
and remix.  
IMPORTANT  
• Spilled fuel is a leading cause of  
hydrocarbon emissions. Some states may  
require the use of automatic fuel shut-off  
containers to reduce fuel spillage.  
• Stored fuel ages.  
• NEVER REFUEL A UNIT WITH THE  
ENGINE RUNNING.  
Do not mix more fuel than you expect to  
use in thirty (30) days, ninety (90) days  
when a fuel stabilizer is added.  
• DO NOT FILL FUEL TANKS INDOORS.  
ALWAYS FILL FUEL TANKS OUTDOORS  
OVER BARE GROUND.  
• Stored two-stroke fuel may separate.  
ALWAYS shake fuel container thoroughly  
before each use.  
• DO NOT OVERFILL FUEL TANK. IT IS NOT  
PERMITTED TO FILL FUEL ABOVE THE  
SHOULDER LEVEL OF FUEL TANK. WIPE  
UP SPILLS IMMEDIATELY.  
• SECURELY TIGHTEN FUEL CAP AFTER  
REFUELING.  
• INSPECT FOR FUEL LEAKAGE.  
IF FUEL LEAKAGE IS FOUND, DO NOT  
START OR OPERATE UNIT UNTIL  
LEAKAGE IS REPAIRED.  
• MOVE AT LEAST 3 M (10 FEET) FROM  
REFUELING LOCATION BEFORE  
STARTING THE ENGINE.  
AFTER USE -  
DO NOT store a unit with fuel in its tank. Leaks can  
occur. Return unused fuel to an approved fuel  
storage container.  
STORAGE -  
Fuel storage laws vary by locality. Contact your  
local government for the laws affecting your area.  
As a precaution, store fuel in an approved, airtight  
container. Store in a well-ventilated, unoccupied  
building, away from sparks and flames.  
Shoulder level  
Fuel tank  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
STARTING COLD ENGINE  
WARNING  
WHEN ENGINE IS STARTED, CONFIRM IF  
THERE IS NOT ANY ABNORMAL VIBRATION  
OR SOUND. IF THERE IS ABNORMAL  
VIBRATION OR SOUND, ASK YOUR DEALER  
TO REPAIR.  
Stand the engine upright on a level surface.  
Place ignition switch in ON (START/RUN)  
position.  
ON  
Ignition switch  
Push purge bulb 3 to 4 times (or until fuel is  
visible in fuel return line).  
STOP  
Shift choke lever to close position (START).  
Pull starter handle until the engine fires.  
Throttle trigger  
Air cleaner  
Throttle trigger lockout  
Shift choke lever to full open position, and if  
necessary, start the engine again and allow to  
warm up before using.  
- The clutch engages at approximately 3500  
r/min. Therefore the drill bit may rotate at  
fast idle engine speed.  
STARTING WARM ENGINE  
Place ignition switch in ON (START/RUN)  
position.  
Push  
Purge bulb  
Pull starter handle until the engine fires.  
- Do not use the choke.  
Fuel return line  
Starter handle  
Choke lever  
STOPPING ENGINE  
RUN  
(Open)  
Set throttle trigger in idle position.  
Place ignition switch in STOP position.  
NOTE  
When engine does not stop, shift choke lever to  
close position.  
Check and repair ignition switch before starting  
the engine again.  
START  
(Close)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
REVERSE ROTATION  
This model is equipped with reverse rotation  
mechanism.  
Counter  
clockwise  
(CCW)  
When drilling, set shift lever down to clockwise  
(CW) rotation position.  
If bit is locked due to deep penetration during  
drilling operation, set shift lever up to  
counterclockwise (CCW) rotation position and  
operate reversed for easy pulling-out.  
Clockwise  
(CW)  
Shift lever  
When changing direction of drill rotation,  
operate as follows:  
- Return engine to idle.  
- Engine shift lever to CW or CCW position  
with a slight acceleration of the throttle  
trigger.  
To properly lock the gears in the gear case.  
- Do not operate shift lever forcibly when  
changing rotation direction.  
NOTE  
WARNING  
• WHEN THE DRILL CAN NOT PULL OUT  
FROM THE WOOD, DO NOT TRY TO PULL  
OUT THE DRILL BY FORCE.  
Do not shift from forward to reverse (or vice-  
versa) while the chuck is turning.  
Failure to do so may cause unit damage.  
Always release throttle and allow the unit to  
return to idle before shifting.  
• WHEN CHANGING THE BIT, ENSURE TO  
STOP THE ENGINE.  
• AFTER A JOB, BIT AND GEAR CASING  
MAY BE HEATED, DO NOT TOUCH THEM  
WITH BARE HANDS.  
Do not stand close to drill or chuck with your  
body or clothes while operation.  
When drilling, ensure that no power cable or  
other obstacle exist.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE AND CARE  
AREA  
MAINTENANCE  
PAGE BEFORE MONTHLY YEARLY  
USE  
DATE  
MAINTENANCE  
PERFORMED  
Air Filter  
Clean/Replace  
13  
13  
Fuel Filter  
Inspect/Clean/  
Replace  
Spark Plug  
Inspect/Clean/  
Adjust/Replace  
13  
Carburetor  
Cooling System  
Silencer  
Adjust  
14  
15  
Inspect/Clean  
Inspect/Tighten/  
Clean  
15  
-
Starter Rope  
Drills  
Inspect/Replace  
Inspect/Clean/  
Lubricate  
-
Fuel Leaks  
Inspect  
13  
Screws, Bolts and Inspect,  
Nuts  
-
-
Tighten/Replace  
Fuel Line  
Inspect  
IMPORTANT  
Time intervals are maximum. Actual use and  
your experience will determine the frequency  
of required maintenance.  
Record dates of monthly and yearly  
inspections.  
EMISSION DATA  
EMISSION CONTROL  
PRODUCT EMISSION DURABILITY  
(EMISSION COMPLIANCE PERIOD)  
The 300 hours emission compliance period is  
the time span selected by the manufacturer  
certifying the engine emissions output meets  
applicable emissions regulations, provided that  
approved maintenance procedures are followed  
as listed in the Maintenance Section of this  
manual.  
(EXHAUSTandEVAPORATIVE)  
EPA 2010 and Later and/or C.A.R.B. TIER III  
The emission control system for the engine is EM  
(engine modifi cation) and, if the second to last  
character of the Engine Family on the Emission  
Control Information label (sample below) is "C", "K",  
or "T",the emission control system is EM and TWC  
(3-way catalyst). The fuel tank/fuel line emission  
control system is EVAP (evaporative emissions).  
Evaporative emissions for California models may  
only be applicable to fuel tanks.  
An Emission Control Label is located on the  
engine. (This is an example only, information on  
label varies by engine family).  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLE SHOOTING  
Trouble  
Engine - hard to start  
Cause  
Remedy  
-
does not start  
Engine  
cranks  
Fuel at  
No fuel  
• Fuel filter clogged  
at carburetor • Fuel line clogged  
• Carburetor  
• Clean or replace  
• Clean  
carburetor  
• Ask your ECHO dealer  
Fuel at  
No fuel at  
cylinder  
• Carburetor  
• Ask your ECHO dealer  
cylinder  
Silencer wet • Fuel mixture is too rich  
with fuel  
• Open choke  
• Clean/replace air filter  
• Adjust carburetor  
• Ask your ECHO dealer  
Spark at  
end of  
No spark at  
end of plug  
wire  
• Ignition switch off  
• Electrical problem  
• Turn switch on  
• Ask your ECHO dealer  
plug wire  
Spark at  
plug  
No spark at  
plug  
• Spark gap incorrect  
• Adjust 0.6 to 0.7 mm  
(0.024 to 0.028 in)  
• Clean or replace  
• Clean or replace  
• Replace plug  
• Covered with carbon  
• Fouled with fuel  
• Spark plug defective  
Engine  
• Internal engine problem  
• Ask your ECHO dealer  
does not  
crank  
Engine  
runs  
Dies or  
• Air filter dirty  
• Clean or replace  
• Clean or replace  
• Clean  
accelerates poorly  
• Fuel filter dirty  
• Fuel vent blocked  
• Spark plug  
• Clean and adjust/replace  
• Adjust  
• Carburetor  
• Cooling system blocked  
• Exhaust port/spark  
arrester screen blocked  
• Clean  
• Clean  
WARNING  
• ALL ENGINE DRILL SERVICE OPERATIONS, OTHER THAN ITEMS LISTED IN THE  
OPERATOR’S MANUAL, SHOULD BE PERFORMED BY AN AUTHORIZED ECHO DEALER.  
• FUEL VAPORS ARE EXTREMELY FLAMMABLE AND MAY CAUSE FIRE AND/OR  
EXPLOSION. NEVER TEST FOR IGNITION SPARK BY GROUNDING SPARK PLUG NEAR  
CYLINDER PLUG HOLE, OTHERWISE SERIOUS PERSONAL INJURY MAY RESULT.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
AIR FILTER  
Clean before use.  
- Remove air cleaner cover and pull out air  
filter.  
- Lightly brush off dust or wash it in water and  
detergent.  
Air filter  
- Dry completely before putting it back in  
place.  
Air cleaner cover  
FUEL FILTER  
Check periodically.  
- Do not allow dust to enter into fuel tank.  
- Clogged filter will cause difficulty in starting  
engine or poor engine performances.  
- Pick up fuel filter through fuel inlet port with  
a piece of steel wire or the like.  
Fuel filter  
Fuel tank cap  
- When filter is dirty, replace it.  
NOTE  
CHECK FUEL SYSTEM  
Federal EPA regulations require all model year  
2012andlatergasolinepoweredengines  
produced for sale in the United States to be  
equipped with a special low permeation fuel  
supply hose between the carburetor and fuel  
tank. When servicing model year 2012 and later  
equipment, only fuel supply hoses certified by  
EPA can be used to replace the original  
equipment supply hose. Fines up to $37,500  
may be enforced for using an un-certified  
replacementpart.  
Check before every use.  
After refueling, make sure fuel does not leak or  
exude from around fuel pipe, fuel grommet or  
fuel tank cap.  
In case of fuel leakage or exudation there is a  
danger of fire. Stop using the machine  
immediately and request your dealer to inspect  
or replace.  
SPARK PLUG  
Checkperiodically.  
- The standard spark gap is 0.6 to 0.7 mm  
(0.024 to 0.028 in).  
- Correct spark gap if it is wider or narrower  
than the standard gap.  
- If the electrodes are coated with carbon  
deposits replace with a new spark plug.  
Do not sandblast to clean.  
0.6 - 0.7 mm (0.024 - 0.028 in)  
Remaining sand will damage engine.  
Fastening torque = 15 to 17 N • m  
(130 to 145 in • lb).  
IMPORTANT  
Do not over tighten plug.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPLACEMENT OF CHUCK  
Replacement of chuck should be done in the  
following manner:  
1. Remove bolt with hexagonal hole fixed in the  
driving axle.  
2. Insert accessory hexagonal bar (Part Number  
895412-20960) into chuck and fix.  
3. Fit 19 mm spanner onto driving axle and keep  
it fitted.  
4. Fit 10 mm box spanner onto the hexagonal bar  
and turn it into direction as indicated by an  
arrow to remove chuck.  
5. Fit a new chuck in the reversed order of  
removing.  
Box spanner  
(10 mm)  
Spanner (19 mm)  
Hexagonal bar  
(Part Number 895412-20960)  
ADJUSTING CARBURETOR  
(As Required)  
GENERAL INFORMATION  
The idle speed adjuster screw controls the throttle  
opening at the idle position.  
IDLE ADJUSTMENT  
1. Start engine and allow it to run at high idle until  
warm.  
Idle speed adjustment screw  
2. Turn the idle speed screw clockwise until drill  
bit begins to move.  
3. Turn idle screw counterclockwise 1 and 1/2 to 2  
turn or until the drill bit stops (2700 to 3300  
r/min).  
High Altitude Operation  
This engine has been factory adjusted to maintain  
satisfactory starting, emission, and durability  
performance up to 1100 feet above sea level (ASL)  
(96.0 kPa). To maintain proper engine operation  
and emission compliance above 1100 feet ASL the  
carburetor may need to be adjusted by an  
authorized ECHO service dealer.  
NOTE  
When there is some trouble with the carburetor,  
contact your dealer.  
IMPORTANT  
If the engine is adjusted for operation above  
1100 feet ASL, the carburetor must be  
readjusted when operating the engine below  
1100 feet ASL, otherwise severe engine damage  
may result.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CLEANING CYLINDER FINS  
(Check Periodically)  
NOTE  
Clogged fins will cause poor engine cooling.  
1. Carefully remove housing and clean dirt and  
dust from fins.  
2. Reinstall housing.  
CLEANING SILENCER AND  
EXHAUST PORT  
(Check Periodically)  
1. Carefully remove housing halves.  
2. Remove and disassemble silencer.  
NOTE  
Be careful not to scratch the cylinder or piston  
when cleaning the cylinder exhaust port.  
3. Clean deposits from cylinder exhaust port and  
silencer.  
STORAGE  
6. Drain the fuel tank completely and pull the  
recoil starter handle several times to remove  
fuel from the carburetor.  
LONG TERM STORAGE  
(Over 30 Days)  
7. Remove the spark plug and pour 1/2  
tablespoon (1/4 oz) of fresh, clean, 2-stroke  
engine oil into the cylinder through the spark  
plug hole.  
Do not store your unit for a prolonged period of  
time (30 days or longer) without performing  
protective storage maintenance which includes the  
following:  
A. Place a clean cloth over the spark plug hole.  
1. Store unit in a dry, dust free place, out of the  
reach of children and other unauthorized  
persons.  
B. Pull the recoil starter handle 2 or 3 times to  
distribute the oil inside the engine.  
C.Observe the piston location through the  
spark plug hole. Pull the recoil starter handle  
slowly until the piston reaches the top of its  
travel and leave it there.  
2. Place ignition switch in STOP position.  
3. Remove accumulation of grease, oil, dirt and  
debris from exterior of unit.  
4. Perform all periodic lubrication and services  
that are required.  
8. Install the spark plug (do not connect ignition  
cable).  
5. Tighten all the screws, bolts and nuts.  
9. Lubricate the drill bit with a heavy coat of oil to  
prevent rust.  
NOTE  
WARNING  
DO NOT STORE IN AN ENCLOSURE WHERE  
FUEL FUMES MAY ACCUMULATE OR  
REACH AN OPEN FLAME OR SPARK.  
For future reference, you should keep this  
operator’smanual.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
EDR-210  
Mass  
Volume  
fuel tank  
Drill  
without drill bit  
kg  
L
4.6 (10.1 lb)  
0.5 (16.9 US fl. oz.)  
size  
mm  
mm  
32 - 178 (1.25 - 7 inch)  
13 (0.5 inch)  
chuck capacity  
speed  
r/min 520  
Mission  
reduction ratio  
17.1 (regular side)  
18.6 (reverse side)  
grease  
lubrication  
External Dimensions  
length × width × height  
mm  
430 × 320 × 265  
without drill bit  
(16.9 × 12.6 × 10.4 inch)  
Engine  
type  
Air cooled Two stroke single cylinder  
engine displacement  
mL(cm³) 21.2 (1.29 cu. inch)  
r/min 9000  
recommended maximum engine speed  
recommended engine idling speed  
r/min 2900  
engine speed at beginning of clutch engagement  
r/min 4000  
carburetor  
ignition  
diaphragm type  
flywheel magneto - CDI system  
spark plug  
starter  
NGK BPM8Y  
recoil starter  
clutch  
automatic centrifugal  
Fuel  
mixture ratio  
50:1 ratio with ECHO Power Blend X,  
ISO-L-EGD (ISO/CD 13738) and JASO  
M345-FC/FD two-stroke, air-cooled engine  
oil.  
gasoline  
Use 89 octane unleaded. Do not use fuel  
containing methyl alcohol, more than 10%  
ethyl alcohol or 15% MTBE. Do not use  
alternative fuels such as E-20 or E-85.  
fuel consumption at engine maximum power  
L/h  
0.47 (15.9 US fl. oz.)  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY STATEMENTS  
ECHO LIMITED WARRANTY STATEMENT FOR  
PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010  
ECHO'S RESPONSIBILITY  
ECHO Incorporated’s Limited Warranty, provides to the original purchaser that this ECHO product is free from defects in material and workmanship.  
Under normal use and maintenance from date of purchase, ECHO agrees to repair or replace at ECHO’s discretion, any defective product  
free of charge at any authorized ECHO servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED  
WARRANTY IS ONLYAPPLICABLE TO ECHO PRODUCTS SOLD BYAUTHORIZED ECHO DEALERS. IT IS EXTENDED TO THE ORIGINAL  
PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair  
parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any  
damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty  
become the property of ECHO, Inc. This warranty is separate from the Emission control warranty statement supplied with your new product.  
Please consult the Emission Control Warranty Statement for details regarding emission related parts. For a list of Authorized ECHO Dealers  
refer to WWW.ECHO-USA.COM or call 1-800-432-ECHO.  
OWNER’S RESPONSIBILITY  
To ensure trouble free warranty coverage it is important that you register your ECHO equipment on-line at WWW.ECHO-USA.COMꢀRUꢀE\ꢀ¿OO-  
LQJꢀRXWꢀWKHꢀZDUUDQW\ꢀUHJLVWUDWLRQꢀFDUGꢀVXSSOLHGꢀZLWKꢀ\RXUꢀXQLWꢁꢀ5HJLVWHULQJꢀ\RXUꢀSURGXFWꢀFRQ¿UPVꢀ\RXUꢀZDUUDQW\ꢀFRYHUDJHꢀDQGꢀSURYLGHVꢀDꢀGLUHFWꢀ  
OLQNꢀLIꢀZHꢀ¿QGꢀLWꢀQHFHVVDU\ꢀWRꢀFRQWDFWꢀ\RXꢁ  
The owner shall demonstrate reasonable care and use, and follow preventative maintenance, storage, fuel and oil usage as prescribed in the  
RSHUDWRU¶VꢀPDQXDOꢁꢀ6KRXOGꢀDꢀSURGXFWꢀGLI¿FXOW\ꢀRFFXUꢂꢀ\RXꢀPXVWꢂꢀDWꢀ\RXUꢀH[SHQVHꢂꢀGHOLYHUꢀRUꢀVKLSꢀ\RXUꢀ(&+2ꢀXQLWꢀWRꢀDQꢀDXWKRUL]HGꢀ(&+2ꢀVHUYLFLQJꢀ  
dealer for warranty repairs (within the applicable warranty period), and arrange for pick-up or return of your unit after the repairs have been  
made. For your nearest authorized ECHO servicing dealer, call ECHO’s Dealer Referral Center, at 1-800-432-ECHO or you can locate an ECHO  
servicing dealer at WWW.ECHO-USA.COM. Should you require assistance or have questions concerning ECHO’s Warranty Statement, you  
can contact our Consumer Product Support Department at 1-800-673-1558 or contact us through the web at WWW.ECHO-USA.COM.  
PRODUCT WARRANTY PERIOD  
RESIDENTIAL APPLICATION  
‡ꢀꢀ 5 YEAR WARRANTY - All units for residential, or non-income producing use will be covered by this limited warranty for ¿YH ꢀꢁꢂꢃ\HDUV from  
date of purchase.  
EXCEPTIONS:  
‡ꢀ )RUꢀWZRꢃVWURNHꢀHQJLQHꢀSRZHUHGꢀSURGXFWVꢂꢀWKHꢀHOHFWURQLFꢀLJQLWLRQꢀPRGXOHꢂꢀÀH[LEOHꢀGULYHꢀFDEOHVꢂꢀ650ꢀVROLGꢀGULYHꢀVKDIWVꢂꢀDQGꢀ7&ꢀWLQHVꢀ  
are warranted for the OLIHꢄ of the product on parts only.  
‡ꢀ &XWWLQJꢀDWWDFKPHQWVꢀVXFKꢀDVꢂꢀEXWꢀQRWꢀOLPLWHGꢀWRꢂꢀEDUVꢂꢀFKDLQVꢂꢀVSURFNHWVꢂꢀEODGHVꢂꢀDQGꢀQ\ORQꢀWULPPHUꢀKHDGVꢀIRUꢀUHVLGHQWLDOꢀRUꢀQRQꢃLQFRPHꢀ  
producing use will be covered for failures due to defects in material or workmanship for a period of ꢅꢆꢃGD\V from original product  
purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by this warranty.  
‡ꢀꢀ (&+2¶Vꢀ5DSLGꢀ/RDGHUꢀ6WULQJꢀ+HDGꢀFDUULHVꢀDꢀOLIHWLPHꢀZDUUDQW\ꢀRQꢀWKHꢀOLQHꢀORFNLQJꢀV\VWHPꢂꢀSDUWVꢀRQO\ꢄꢀQRꢀODERUꢁꢀ5HIHUꢀWRꢀ\RXUꢀRSHUDWRU¶Vꢀ  
manual for string head installation and maintenance instructions.  
‡ꢀꢀ $OO6%ꢃ6HULHVDQG352ꢀ$77$&+0(176(5,(66SOLW6KDIWDWWDFKPHQWVFDUU\WKHVDPHZDUUDQW\GXUDWLRQDVWKHXQLWVWKH\DUHꢀ  
GHVLJQHGꢀWRꢀ¿Wꢁ  
COMMERCIAL APPLICATION  
‡ꢀꢀ 1 YEAR WARRANTY - All Chain Saws, QuikVent Saws, and Cut-Off Saws for commercial, institutional, agricultural, industrial, or income  
producing use will be covered by this limited warranty for one ꢀꢇꢂꢃ\HDU from the date of purchase.  
‡ꢀꢀ 2 YEAR WARRANTY - All other units for commercial, institutional, agricultural, industrial, or income producing use will be covered by this  
limited warranty for two ꢀꢈꢂꢃ\HDUV from the date of purchase.  
EXCEPTIONS:  
‡ꢀ )RUꢀWZRꢃVWURNHꢀHQJLQHꢀSRZHUHGꢀSURGXFWVꢂꢀWKHꢀHOHFWURQLFꢀLJQLWLRQꢀPRGXOHꢂꢀÀH[LEOHꢀGULYHꢀFDEOHVꢂꢀ650ꢀVROLGꢀGULYHꢀVKDIWVꢀDQGꢀ7&ꢀWLQHVꢂꢀ  
are warranted for the OLIHꢄ of the product on parts only.  
‡ꢀ &XWWLQJꢀDWWDFKPHQWVꢀVXFKꢀDVꢂꢀEXWꢀQRWꢀOLPLWHGꢀWRꢂꢀEDUVꢂꢀFKDLQVꢂꢀVSURFNHWVꢂꢀEODGHVꢂꢀDQGꢀQ\ORQꢀWULPPHUꢀKHDGVꢀIRUꢀFRPPHUFLDOꢂꢀLQVWLWXWLRQDOꢂꢀ  
agricultural, industrial, rental, or income producing will be covered for failures due to defects in material or workmanship for a period  
of ꢉꢆꢃGD\V from original product purchase date. Any misuse from contact with concrete, rocks, or other structures is not covered by  
this warranty.  
‡ꢀꢀ (&+2¶Vꢀ5DSLGꢀ/RDGHUꢀ6WULQJꢀ+HDGꢀFDUULHVꢀDꢀOLIHWLPHꢀZDUUDQW\ꢀRQꢀWKHꢀOLQHꢀORFNLQJꢀV\VWHPꢂꢀSDUWVꢀRQO\ꢄꢀQRꢀODERUꢁꢀ5HIHUꢀWRꢀ\RXUꢀRSHUDWRU¶Vꢀ  
manual for string head installation and maintenance instructions.  
‡ꢀꢀ $OO6%ꢃ6HULHVDQG352ꢀ$77$&+0(176(5,(66SOLW6KDIWDWWDFKPHQWVFDUU\WKHVDPHZDUUDQW\GXUDWLRQDVWKHXQLWVWKH\DUHꢀ  
GHVLJQHGꢀWRꢀ¿Wꢁ  
RENTAL APPLICATION - 90 DAYS WARRANTY  
‡ꢀꢀ8QLWVꢀIRUꢀUHQWDOꢀXVHꢀZLOOꢀEHꢀFRYHUHGꢀDJDLQVWꢀGHIHFWVꢀLQꢀPDWHULDOꢀDQGꢀZRUNPDQVKLSꢀIRUꢀDꢀSHULRGꢀRIꢀꢅꢆꢀGD\VꢀIURPꢀWKHꢀGDWHꢀRIꢀSXUFKDVHꢁꢀ  
ꢀꢀ (&+2¶VꢀOLDELOLW\ꢀXQGHUꢀWKHꢀ³/LIHWLPH´ꢀFRYHUDJHꢀLVꢀOLPLWHGꢀWRꢀIXUQLVKLQJꢀSDUWVꢀVSHFL¿HGꢀXQGHUꢀWKHꢀ352'8&7ꢀ:$55$17<ꢀ3(5,2' section of  
this warranty statement for ³/LIH´ꢀIUHHꢀRIꢀFKDUJHꢀIRUꢀDꢀSHULRGꢀRIꢀWHQꢀꢇꢈꢆꢉꢀ\HDUVꢀDIWHUꢀWKHꢀGDWHꢀRIꢀWKHꢀFRPSOHWHꢀXQLW¶Vꢀ¿QDOꢀSURGXFWLRQꢁꢀ  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PURCHASED REPAIR PARTS, SHORT BLOCKS AND ACCESSORIES  
‡ꢀꢀꢅꢆꢃGD\ꢀUHVLGHQWLDOꢂꢀRUꢀQRQꢃLQFRPHꢀSURGXFLQJꢀZDUUDQW\  
‡ꢀꢀꢊꢆꢃGD\ꢀFRPPHUFLDOꢂꢀLQVWLWXWLRQDOꢂꢀDJULFXOWXUDOꢂꢀLQGXVWULDOꢂꢀLQFRPHꢀSURGXFLQJꢂꢀRUꢀUHQWDOꢀDSSOLFDWLRQꢀZDUUDQW\ꢀꢀ  
ATTENTION TWO-STROKE ENGINE POWER PRODUCT OWNERS  
This ECHO two-stroke engine power product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior  
performance. To help ensure the performance of the unit, it is required to use two-stroke oil which meets the ISO-L-EGD Standard per ISO/CD  
13738 and JASO M345FD Standards. (&+2ꢃ3RZHUꢃ%OHQGŒꢃ7ZRꢊ6WURNHꢃ2LO LVꢀDꢀSUHPLXPꢀWZRꢃVWURNHꢀRLOꢀVSHFL¿FDOO\ꢀIRUPXODWHGꢀWRꢀPHHWꢀ,62ꢃ  
L-EGD (ISO/CD 13738) and JASO M345FD Standards. The use of two-stroke oils designed for other applications, such as for outboard motors  
or lawnmowers can result in severe engine damage, and will void your two-stroke engine limited warranty.  
THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY:  
‡ꢀ  
/DFNꢀRIꢀOXEULFDWLRQꢀRUꢀHQJLQHꢀIDLOXUHꢂꢀGXHꢀWRꢀWKHꢀXVHꢀRIꢀWZRꢃVWURNHꢀRLOVꢀthat do not meet the ISO-L-EGD (ISO/CD 13738) and JASO M345FD  
Standards. Engine problems due to inadequate lubrication caused by failure to use an ISO-L-EGD compliant and JASO M345FD registered  
oil, will void the two-stroke engine limited warranty. (&+23RZHU%OHQGŒ7ZRꢃ6WURNH2LO meets the ISO-L-EGD and JASO M345FD  
Standard. Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two-stroke oil used, per  
the statement listed in the EPA or California Emission Defect Warranty Explanation.  
‡ꢀ  
'DPDJHꢀFDXVHGꢀE\ꢀXVHꢀRIꢀJDVRKROꢂꢀFRQWDLQLQJꢀPHWKDQROꢀꢇZRRGꢀDOFRKROꢉꢂꢀRUꢀJDVROLQHꢀFRQWDLQLQJꢀOHVVꢀWKDQꢀꢋꢅꢀRFWDQH. Only use gasoline which  
contains ꢋꢅꢀRFWDQHꢀRUꢀKLJKHU. Gasohol which contains a PD[LPXPꢀꢈꢆꢌꢀHWKDQROꢀꢇJUDLQꢀDOFRKROꢉꢀRUꢀꢈꢍꢌꢀ07%(ꢀꢇPHWK\OꢎWHUWLDU\ꢎEXW\OꢎHWKHUꢉꢀ  
is also approved. The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator’s manual.  
(QJLQHꢀGDPDJHꢀFDXVHGꢀE\ꢀXVHꢀRIꢀHWKHUꢀRUꢀDQ\ꢀVWDUWLQJꢀÀXLGVꢁꢀꢀ  
'DPDJHꢀFDXVHGꢀE\ꢀWDPSHULQJꢀZLWKꢀHQJLQHꢀVSHHGꢀJRYHUQRUꢀRUꢀHPLVVLRQꢀFRPSRQHQWVꢂꢀRUꢀUXQQLQJꢀHQJLQHVꢀDERYHꢀVSHFL¿HGꢀDQGꢀUHFRPPHQGHGꢀ  
engine speeds as listed in your operator’s manual.  
‡ꢀ  
‡ꢀ  
‡ꢀ  
‡ꢀ  
‡ꢀ  
2SHUDWLRQꢀRIꢀWKHꢀXQLWꢀZLWKꢀLPSURSHUO\ꢀPDLQWDLQHGꢎUHPRYHGꢀFXWWLQJꢀVKLHOGꢀRUꢀUHPRYHGꢎGDPDJHGꢀDLUꢀ¿OWHUꢁꢀꢀ  
'DPDJHꢀFDXVHGꢀE\ꢀGLUWꢂꢀSUHVVXUHꢀRUꢀVWHDPꢀFOHDQLQJꢀWKHꢀXQLWꢂꢀVDOWꢀZDWHUꢂꢀFRUURVLRQꢂꢀUXVWꢂꢀYDUQLVKꢂꢀDEUDVLYHVꢂꢀDQGꢀPRLVWXUHꢁ  
'HIHFWVꢂꢀPDOIXQFWLRQVꢀRUꢀIDLOXUHVꢀUHVXOWLQJꢀIURPꢀDEXVHꢂꢀPLVXVHꢂꢀQHJOHFWꢂꢀPRGL¿FDWLRQVꢂꢀDOWHUDWLRQVꢂꢀQRUPDOꢀZHDUꢂꢀLPSURSHUꢀVHUYLFLQJꢂꢀRUꢀXVHꢀ  
of unauthorized attachments.  
‡ꢀ  
‡ꢀ  
,QFRUUHFWꢀVWRUDJHꢀSURFHGXUHVꢂꢀVWDOHꢀIXHOꢂꢀLQFOXGLQJꢀIDLOXUHꢀWRꢀSURYLGHꢀRUꢀSHUIRUPꢀUHTXLUHGꢀPDLQWHQDQFHꢀVHUYLFHVꢀDVꢀSUHVFULEHGꢀLQꢀWKHꢀRSHUDWRUꢏVꢀ  
manual. Preventative maintenance as outlined in the operators manual is the customer’s responsibility.  
)DLOXUHVꢀGXHꢀWRꢀLPSURSHUꢀVHWꢃXSꢂꢀSUHꢃGHOLYHU\ꢀVHUYLFHꢀRUꢀUHSDLUꢀVHUYLFHꢀE\ꢀDQ\RQHꢀRWKHUꢀWKDQꢀDXWKRUL]HGꢀ(&+2ꢀVHUYLFLQJꢀGHDOHUꢀGXULQJꢀWKHꢀ  
warranty period.  
‡ꢀ  
‡ꢀ  
&HUWDLQꢀparts and other items are not warranted, including but not limited to: lubricants, starter cords, and engine tune-ups.  
8VHRIVSDUNSOXJVRWKHUWKDQWKRVHPHHWLQJSHUIRUPDQFHDQGGXUDELOLW\UHTXLUHPHQWVRIWKH2(0VSDUNSOXJOLVWHGLQWKH2SHUDWRUꢏVꢀ  
Manuals.  
‡ꢀ  
2YHUKHDWLQJꢀRUꢀFDUERQꢀVFRULQJꢀIDLOXUHVꢀGXHꢀWRꢀUHVWULFWHGꢂꢀFORJJHGꢀH[KDXVWꢀSRUWꢀRUꢀFRPEXVWLRQꢀFKDPEHUꢂꢀLQFOXGLQJꢀGDPDJHꢀWRꢀVSDUNꢀDUUHVWHUꢀ  
screen.  
‡ꢀ  
‡ꢀ  
$GMXVWPHQWVꢀDIWHUꢀWKHꢀ¿UVWꢀꢇꢊꢆꢉꢀWKLUW\ꢀGD\VꢀDQGꢀEH\RQGꢂꢀVXFKꢀDVꢀFDUEXUHWRUꢀDGMXVWPHQWꢀDQGꢀWKURWWOHꢀFDEOHꢀDGMXVWPHQWꢁꢀ  
'DPDJHꢀWRꢀJHDUVꢀRUꢀJHDUꢀFDVHVꢀFDXVHGꢀE\ꢀFRQWDPLQDWHGꢀJUHDVHꢀRUꢀRLOꢂꢀXVHꢀRIꢀLQFRUUHFWꢀW\SHꢀRUꢀYLVFRVLW\ꢀRIꢀOXEULFDQWVꢂꢀDQGꢎRUꢀIDLOXUHꢀWRꢀFRPSO\ꢀ  
with recommended grease or oil change intervals.  
®
‡ꢀ  
‡ꢀ  
‡ꢀ  
'DPDJHꢀFDXVHGꢀE\ꢀORDGLQJꢀ6+5('ꢀꢏ1ꢏꢀ9$& beyond recommended capacity.  
'DPDJHꢀFDXVHGꢀE\ꢀSXPSꢀRUꢀVSUD\HUꢀUXQQLQJꢀGU\ꢂꢀSXPSLQJꢀRUꢀVSUD\LQJꢀFDXVWLFꢀRUꢀÀDPPDEOHꢀPDWHULDOVꢂꢀRUꢀODFNꢀRIꢀRUꢀEURNHQꢀVWUDLQHUVꢁꢀ  
$GGLWLRQDOꢀGDPDJHꢀWRꢀSDUWVꢀRUꢀFRPSRQHQWVꢀGXHꢀWRꢀFRQWLQXHGꢀXVHꢀDIWHUꢀRSHUDWLRQDOꢀSUREOHPꢀRUꢀIDLOXUHꢀRFFXUVꢁꢀ6KRXOGꢀRSHUDWLRQDOꢀSUREOHPꢀRUꢀ  
failure occur, the product should not be used, but delivered as is to an authorized ECHO servicing dealer.  
It is a dealer’s and/or customer’s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting  
WWW.ECHO-USA.COMꢁꢀ<RXUꢀUHFHLSWꢀRIꢀSXUFKDVHꢀLQFOXGLQJꢀGDWHꢂꢀPRGHOꢀDQGꢀVHULDOꢀQXPEHUꢀPXVWꢀEHꢀPDLQWDLQHGꢀDQGꢀSUHVHQWHGꢀWRꢀDQꢀDXWKRUL]HGꢀ  
ECHO servicing dealer for warranty service. Proof of purchase rests solely with the customer. Some states do not allow limitations on how long  
an implied warranty lasts, so the above limitations may not apply to you. Some states do not allow the exclusion or limitation of incidental or  
FRQVHTXHQWLDOꢀGDPDJHVꢂꢀVRꢀ\RXꢀPD\ꢀDOVRꢀKDYHꢀRWKHUꢀVSHFL¿FꢀOHJDOꢀULJKWVꢀZKLFKꢀYDU\ꢀIURPꢀVWDWHꢀWRꢀVWDWHꢁꢀ7KLVꢀOLPLWHGꢀZDUUDQW\ꢀLVꢀJLYHQꢀE\ꢀ(&+2ꢀ  
Incorporated, 400 Oakwood Rd., Lake Zurich, IL 60047.  
DISCLAIMER OF IMPLIED WARRANTIES  
7KLVꢀOLPLWHGꢀZDUUDQW\ꢀLVꢀLQꢀOLHXꢀRIꢀDOOꢀRWKHUꢀH[SUHVVHGꢀRUꢀLPSOLHGꢀZDUUDQWLHVꢂꢀLQFOXGLQJꢀDQ\ꢀZDUUDQW\ꢀRIꢀ),71(66ꢀ)25ꢀ$ꢀ3$57,&8/$5ꢀ385326(ꢀ  
OR USE and any implied warranty of MERCHANTABILITYꢀRWKHUZLVHꢀDSSOLFDEOHꢀWRꢀWKLVꢀSURGXFWꢁꢀ(&+2ꢀDQGꢀLWVꢀDI¿OLDWHGꢀFRPSDQLHVꢀVKDOOꢀQRWꢀEHꢀ  
OLDEOHꢀIRUꢀDQ\ꢀVSHFLDOꢀLQFLGHQWDOꢀRUꢀFRQVHTXHQWLDOꢀGDPDJHꢂꢀLQFOXGLQJꢀORVWꢀSUR¿WVꢁꢀ7KHUHꢀDUHꢀQRꢀZDUUDQWLHVꢀH[WHQGHGꢀRWKHUꢀWKDQꢀDVꢀSURYLGHGꢀKHUHLQꢁꢀ  
7KLVꢀOLPLWHGꢀZDUUDQW\ꢀPD\ꢀEHꢀPRGL¿HGꢀRQO\ꢀE\ꢀ(&+2ꢁ  
99922201032  
11/18/2011  
E01305001001/E01305999999  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Electrolux Microwave Oven 267554 User Manual
Electro Voice Speaker System Fri+122 64 User Manual
Estate Dishwasher TUD6710P User Manual
Extron electronic Pacemaker MTP 15HD RS User Manual
FoodSaver Food Saver v825 User Manual
GE Dehumidifier ADEHSO User Manual
Gefen TV Cables GTV HDMI 2 COMPSVIDS User Manual
GE Microwave Oven PEM31SMSS User Manual
GE Monogram Refrigerator Side by Side Refrigerators User Manual
GE Ventilation Hood 49 80565 User Manual