Power PrunerTM Attachment
Operator's Manual
MODEL
99944200532
FOR MODELS SRM-2100SB/2400SB
SRM-210SB/211SB
SRM-225SB
ENGLISH
ESPAñOL
FRANCAIS
SRM-260SB/261SB
PAS-2100/2400
PAS-210/211
PAS-230/231
PAS-260/261
PAS-265
WARNING
Read rules for safe operation and instructions carefully. ECHO provides an Opera-
tor's Manual and a Safety Manual for Pro Attachment Series power source or Split
Boom Trimmer. Those manuals and this manual must be read and understood for
proper and safe operation, otherwise serious personal injury may result.
X770001161
10/09
X7702092201
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
Po w e r Pr u n e r AT T A c h M e n T
3
oP e r A T o r 's MA n u A l
sa f e t y
m a n u a l s a f e t y s y m b o l s a n d Im p o r t a n t In f o r m a t Io n
Throughout this manual and on the product itself, you will find safety alerts and helpful, informational messages pre-
ceded by symbols or key words. The following is an explanation of those symbols and key words and what they mean to
you.
CIRCLE AND SLASH SyMBOL
DANGER
This symbol means the specific action
shown is prohibited. Ignoring these prohi-
bitions can result in serious or fatal injury.
The safety alert symbol accompanied by the word
“DANGER” calls attention to an act or condition
which WILL lead to serious personal injury or
death if not avoided.
NOTE
WARNING
This enclosed message provides tips for use, care and
maintenance of the unit.
The safety alert symbol accompanied by the word
“WARNING” calls attention to an act or condi-
tion which CAN lead to serious personal injury or
death if not avoided.
IMPORTANT
The enclosed message provides information neces-
sary for the protection of the unit.
CAUTION
The safety alert symbol accompanied by the word
“CAUTION” calls attention to an act or condition
which may lead to minor or moderate personal
injury if not avoided.
In t e r n a t Io n a l s y m b o l s
Symbol
description/application
Symbol
description/application
Symbol
description/application
Symbol
description/application
Symbol form/shape
Symbol form/shape
Symbol form/shape
Symbol form/shape
Wear slip resis-
tant foot wear.
DO NOT allow
flames or sparks
near fuel.
Read and understand
Operator's Manual.
Fuel and oil mixture
Finger Severing
Ignition
ON/OFF
Engine choke
control.
Wear eyes, ears and
head protection
Wear hand
protection. Use
two handed.
Hot
Surface
Emergency stop
Primer
bulb
DO NOT smoke
near fuel.
Safety/Alert
Carburetor adjustment
- High speed mixture
Chain lubrication
Avoid all power
lines. This unit
is not insulated
against electrical
current.
Carburetor adjustment
- Idle speed
Do not operate
closer than 15 M
(50 ft.) from elec-
trical hazards.
Carburetoradjustment
- Low speed mixture
Keep bystanders
at least 15 meters
(50 feet) away.
Plan retreat
path from falling
objects.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
p e r s o n a l c o n d It Io n a n d s a f e t y e q u Ip m e n t
WARNING
Power PrunerTM Attachment users risk injury to themselves and others if the Power PrunerTM Attachment is used
improperly and or safety precautions are not followed. Proper clothing and safety gear must be worn when oper-
ating a Power PrunerTM.
Hearing Protection
ECHO recommends wearing hearing protection whenever
unit is used.
Physical Condition
Your judgment and physical dexterity may not be good:
• if you are tired or sick,
• if you are taking medication,
• if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Proper Clothing
Wear snug fitting, durable protective clothing; chain saw
safety pants or chaps are recommended.
• Pants should have long legs, shirts with long sleeves.
• DO NOT WEAR SHORTS,
Eye Protection
Wear eye protection that meets ANSI Z87.1 or CE require-
ments whenever you operate the unit
• DO NOT WEAR TIES, SCARVES, JEWELRY.
Wear sturdy protective safety shoes or boots with non-
skid soles;
• DO NOT WEAR OPEN TOED SHOES,
• DO NOT OPERATE UNIT BAREFOOTED.
Keep long hair away from engine and air intake. Retain
hair with cap or net.
Face and Head Protection
When trimming overhead, always wear head protection
meeting ANSI Z89.1 or CE requirements with a full face
shield. Head protection with full face shield will help
protect you from falling branches and debris.
Hand Protection
Wear no-slip, heavy duty work gloves to improve your
grip on the unit handles. Gloves also reduce the transmis-
sion of machine vibration to your hands.
Hot Humid Weather
Heavy protective clothing can increase operator fatigue,
which may lead to heat stroke. Schedule heavy work for
early morning or late afternoon hours when temperatures
are cooler.
Vibration and Cold --
It is believed that a condition called Raynaud’s Phenomenon, which affects the fingers of certain individuals may be
brought about by exposure to vibration and cold. Exposure to vibration and cold may cause tingling and burning sen-
sations followed by loss of color and numbness in the fingers. The following precautions are strongly recommended
because the minimum exposure which might trigger the ailment is unknown.
• Keep your body warm, especially the head, neck, feet, ankles, hands
and wrists.
• Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks and also by not smoking.
• Limit the hours of operation. Try to fill each day with jobs where
operating the trimmer or other hand-held power equipment is not
required.
• If you experience discomfort, redness and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
Po w e r Pr u n e r AT T A c h M e n T
5
oP e r A T o r 's MA n u A l
Repetitive Stress Injuries --
It is believed that overusing the muscles and tendons of the fingers, hands, arms and shoulders may cause soreness,
swelling, numbness, weakness and extreme pain in those areas. Certain repetitive hand activities may put you at a high
risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which
could occur when your wrist swells and squeezes a vital nerve that runs through the area. Some believe that prolonged
exposure to vibration may contribute to CTS. CTS can cause severe pain for months or even years.
To reduce the risk of RSI/CTS, do the following:
• Avoid using your wrist in a bent, extended or twisted position. In-
stead try to maintain a straight wrist position. Also, when grasping,
use your whole hand, not just the thumb and index finger.
• Take periodic breaks to minimize repetition and rest your hands.
• Reduce the speed and force with which you do the repetitive move-
ment.
• Do exercises to strengthen the hand and arm muscles.
• Immediately stop using all power equipment and consult a doctor if
you feel tingling, numbness or pain in the fingers, hands, wrists or
arms. The sooner RSI/CTS is diagnosed,the more likely permanent
nerve and muscle damage can be prevented.
Guide Bar and Saw Chain
DANGER
• Serious injury may result from the use of non approved guide
bar and saw chain combinations. Read and comply with all
safety instructions listed in this manual.
• ECHO, INC. will not be responsible for the failure of cutting
devices or accessories which have not been tested and approved
by ECHO for use with this unit.
• Never adjust the guide bar or saw chain when the engine is operating.
• Check that the cutting attachment, guide bar and saw chain is firmly
attached and in safe operating condition.
• Only use ECHO approved guide bar and saw chain.
• Do not hit rocks, stones, tree stumps and other foreign objects with
the saw chain.
• Do not cut into the ground with the saw chain.
• If saw chain strikes an obstruction, stop engine immediately and
inspect saw chain for damage.
• Do not operate with a dull, broken or discolored saw chain.
• Remove all foreign objects from work area.
• Always cover the guide bar and saw chain with guide bar cover dur-
ing transportation and in storage.
DANGER
All over head electrical conductors and communications wires can
have electricity flow with high voltages. Never touch wires directly
or indirectly when pruning, otherwise serious injury or death may
result.
Read the Manuals
• Provide all operators of this equipment with the Operator's Manual,
and instructions for safe operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Clear the Work Area
• Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15 m (50 ft.) while the
unit is in use.
Use Proper Clothing & Equipment
• Always wear head protection with full face shield to help protect
against falling branches and debris.
Keep A Firm Grip
• Hold the front and rear handles with both hands with thumbs and
fingers encircling the handles
Keep A Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery,
uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not overreach.
• Operate the Power PrunerTM only from the ground or out of an ap-
proved bucket lift.
• Always evaluate the branches to be pruned for hazards such as loose
dead branches which may fall and strike the operator or helpers.
Remove hazards before pruning.
• Plan retreat path from falling objects.
• Cut branches bounce when striking ground.
• Turn the Power PrunerTM off when moving from tree to tree.
• Avoid any contact with saw chain.
Avoid Hot Surfaces
• Keep exhaust area clear of flammable debris. Avoid contact during
and immediately after operation.
k Ic k b a c k
DANGER
Kickback can lead to dangerous loss of control of the Power
PrunerTM and result in serious injury to the operator or any one
standing close by. Hold the Power PrunerTM firmly with both hands
with thumbs and fingers encircling the front and rear handles. Be
aware of the down and outward path the pruner will take after the
cut is made.
Kickback may occur when the moving saw chain at the nose or tip of
the guide bar touches an object, or when the wood closes in and pinches
the saw chain in the cut. In some cases this may cause a lightning-fast
reverse action, kicking the guide bar and saw chain up and back or
down and back towards the operator. Either of these reactions may
cause the operator to lose control of the Power PrunerTM which could
result in serious personal injury.
With a basic understanding of kickback, you can reduce or eliminate
the element of surprise which contributes to accidents.
Avoid contact of the guide bar tip with any object while the saw chain
is moving.
Cut only wood. Avoid striking concrete, metal, wire, or other obstruc-
tions which could cause kickback or damage to the saw chain.
If the saw chain does strike a foreign object, immediately stop the en-
gine, inspect and repair the Power PrunerTM if necessary.
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
Po w e r Pr u n e r AT T A c h M e n T
7
oP e r A T o r 's MA n u A l
e q u Ip m e n t
Before operation a complete check of the unit must be performed;
• Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings.
• ALWAyS stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit.
• DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit.
• NEVER reach into any opening while the engine is running. Moving parts may not be visible through openings.
de s c r Ip t Io n
Locate this safety decal on your attachment. Make sure the decal is legible and that you understand and follow the
instructions on it. If it cannot be read, a new one can be ordered from your ECHO dealer. See PARTS ORDERING
instructions for specific information.
1
9
P/N X505001821
1. GRIP, FRONT - Cushioned grip for left hand.
2. SHAFT DECAL - Contain important safety information that must be followed.
3. LOWER DRIVE SHAFT ASSEMBLy - Contains a specially designed liner and the flexible drive shaft.
4. CUTTING ATTACHMENT - Sealed, gear ratio is 1.5:1 reduction.
5. AUTOMATIC OILER ASSEMBLy - Self oiling. Use high quality, low viscosity, non detergent bar and chain oil.
6. SAW CHAIN - 91 VX 9.53mm (3/8 inch) low profile Oregon® saw chain. Runs approximately 725 m/min.
(2378 ft/min) at 6500 RPM.
7. GUIDE BAR - 254 mm (10 inch) Bar
8. CUTTING SHOE - Used to capture and stabilize branch while cutting. Place cutting shoe against branch, accelerate
and lower saw chain into branch.
9. GUIDE BAR COVER - Used to cover guide bar and saw chain during transport and storage. Remove guide bar
cover before using unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
co n t e n t s
The ECHO product you purchased has been factory pre-assembled for your convenience. After opening the carton, check
for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to
check for missing parts.
1 - Power PrunerTM Attachment
- Plastic Bag (co-pack)
- Operators Manual
- Safety Manual
- Warranty Registration Card
- Guide Bar Cover
- Storage Hook Assembly
as s e m b l y
p o w e r h e a d s h a f t /l o w e r s h a f t a s s e m b l y
B
Tools Required: None
D
Parts Required: PAS or SRM-SB Power Head w/Shaft & Coupling.
1. Set Power Head/Shaft Assembly on a level surface.
2. Pull locator pin (A) out, and turn counter-clockwise 1/4 turn to lock-
out position.
A
3. Remove vinyl cap from attachment drive shaft.
D
C
4. Carefully fit attachment drive shaft assembly into coupler (B) to
decal assembly line (C), making sure that the inner lower drive shaft
engages into the square upper drive shaft socket.
NOTE
Earlier model Power Heads may have shorter couplings. Short
couplings fit flush to decal point (E). New couplings are 4-3/4 in.
long, and fit flush to line (C).
NOTE
Lower bearing housing and head assembly must be in line with the
engine.
E
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
Po w e r Pr u n e r AT T A c h M e n T
9
oP e r A T o r 's MA n u A l
5. Rotate locator pin (A) 1/4 turn clockwise to engage lower shaft
hole. Insure locator pin is fully engaged by twisting lower drive
shaft. Locator pin should snap flush in coupler. Full engagement
will prevent further shaft rotation.
6. Secure lower shaft assembly to coupler by tightening clamping
knob (D).
f r o n t l o o p h a n d l e r e m o v a l
Tools Required: Screwdriver.
Parts Required: None
NOTE
Front loop handles/loop handles with barrier bars are not recom-
mended for use with Power Pruner attachment.
1. Remove front handle assembly, barrier bar (if installed), and mount-
ing hardware from PAS or SRM-SB power head.
2. Retain parts for future use.
s a w c h a In t e n s Io n a d j u s t m e n t
Tools Required: 10 mm Wrench, Screwdriver
WARNING
Always wear gloves when handling saw chain, otherwise serious
personal injury may result.
To Adjust Saw Chain Tension.
1. Loosen two (2) guide bar nuts (A) located on cutting attachment.
B
2. Turn saw chain tensioner screw (B) clockwise to tighten saw chain
on guide bar. Turning screw counter clockwise will loosen saw
chain on guide bar.
A
3. Tighten guide bar nuts firmly. Move saw chain backwards on guide
bar by hand. Saw chain should move freely on guide bar if it is
in proper mesh with sprocket. If saw chain is difficult to rotate or
binds on guide bar, it is too tight.
Keep the saw chain lubricated and properly adjusted and the guide bar
nuts tightened firmly at all times.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
op e r a t Io n
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop
before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear
gloves to protect hands from sharp edges and hot surfaces.
NOTE
Refer to your Pro Attachment Series power source or Split Boom
Operator's Manual for correct engine fueling, starting and stopping
instructions.
IMPORTANT
Guide bar cover is for travel/storage only. Remove cover before
using unit.
l u b r Ic a t In g t h e g u Id e b a r a n d s a w c h a In
Automatic Oiling System
1. Wipe debris from around oil fill cap.
2. Remove oil fill cap and fill reservoir with a quality, low viscosity
guide bar and saw chain oil.
NOTE
The discharge volume of the automatic oiler is preset to deliver 3
to 4 cc/min. at normal operating RPM. During heavy or dry cutting
conditions the oil discharge volume may be adjusted to assure ad-
equate lubrication. Refill the oil reservoir with each tank of fuel.
IMPORTANT
To prevent plastic deterioration, do not use synthetic or silicone
based oil.
a d j u s t In g a u t o m a t Ic o Il e r
Tools required: Screwdriver
A
1. From bottom of gear case, turn adjustment screw (A) clockwise to
decrease oil volume - counter clockwise to increase oil volume.
NOTE
Very little visible oil on the saw chain will provide sufficient lubri-
cation.
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
Po w e r Pr u n e r AT T A c h M e n T
oP e r A T o r 's MA n u A l 11
p r u n In g t e c h n Iq u e s
corre
The Power Pruner™ Attachment is designed for light to medium trim-
ming of limbs and branches up to 203 mm (8 in.) in diameter. Follow
these tips for successful operation.
• Plan cut carefully. Check direction branch will fall.
• Long branches should be removed in several pieces.
• Do not stand directly beneath branch being cut.
guIde
br
not
correct
• When ready to cut:
Hold "cutting shoe" against branch. This will prevent whipping of the
branch. DO NOT use back and forth sawing action.
• Look out for branches immediately behind the branch being cut. If
saw chain hits rear branch, damage to the saw chain my occur.
• Accelerate to full throttle.
blade hIts rear branch
• Apply cutting pressure.
• Ease cutting pressure when nearing end of cut to maintain control.
• When pruning a limb 102 mm (4 in.) diameter or larger cut as fol-
lows:
1. Under cut 1/4 limb diameter near tree trunk.
2. Finish top cut slightly farther out on limb.
3. Flush cut stub at trunk.
not
• DO NOT use for felling or bucking.
correct
ma In t e n a n c e
WARNING
Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all
openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete
stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service.
Wear gloves to protect hands from sharp edges and hot surfaces.
Your ECHO Pruner attachment is designed to provide many hours of trouble free service. Regular scheduled mainte-
nance will help your Pruner attachment achieve that goal. If you are unsure or are not equipped with the necessary tools,
you may want to take your unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to
DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see
your ECHO Dealer for repairs.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
s k Il l l e v e l s
Level 1 =
Level 2 =
Easy to do. Common tools may be required.
Moderate difficulty. Some specialized tools may be required.
m a In t e n a n c e In t e r v a l s
Component Maintenance Procedure
Skill Level
Interval
Drive Shaft
Grease
1
2
2
1
Every 25 hours of use
Before Each Use
Before Each Use
Before Each Use
Guide Bar
Inspect/Clean/Lubricate
Inspect/Sharpen/Replace/Tension
Inspect/Tighten/Replace
Saw Chain
Screws/Nuts/Bolts
IMPORTANT - Time intervals shown are maximum. Actual use and your experience will determine the frequen-
cy of required maintenance.
l u b r Ic a t Io n
Drive Shaft (Lower)
Level 1
Tools Required: 4 mm L-Wrench
Parts Required: POWER BLENDXTM 8 oz. (P/N 91014) or Lithium
Base Grease.
B
IMPORTANT
Lower and upper drive shaft must be lubricated with high tem-
perature automotive grease every 25 hours of operation, otherwise
drive shaft assembly overheating and failure can result.
1. Remove the cutting attachment from the Power PrunerTM shaft
housing by removing the locating bolt (A), loosening the (2) two
bolts (B) clamping the cutting attachment to the shaft housing, and
sliding the cutting attachment off.
A
2. Remove lower flex cable, wipe clean, and apply a thin coat 15ml
(1/2 oz.) of high temperature automotive grease.
3. Reinstall cable. Make sure cable end engages upper drive shaft
adaptor.
4. Slide the cutting attachment onto the shaft housing until the hole
in the neck of the cutting attachment is aligned with the hole (C) in
the housing (It may be necessary to rotate the saw chain slightly to
align the internal pinion and drive shaft.)
B
5. Insert locating bolt (A) and tighten to snug.
6. Tighten bolts (B), clamping the cutting attachment onto the hous-
ing.
C
A
B
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
Po w e r Pr u n e r AT T A c h M e n T
oP e r A T o r 's MA n u A l 13
g u Id e b a r a n d s a w c h a In r e p l a c e m e n t
WARNING
Never try to replace or adjust guide bar and saw chain with engine running. Always disconnect spark plug wire
before servicing guide bar and saw chain. This saw chain is VERY sharp, wear heavy gloves to protect your hands
when handling it. Wear eye protection meeting CE or ANSI specification Z87.1.
Guide Bar Replacement / Installation
Level 2
Tools Required: 10 mm Wrench, 4mm Hex Wrench
1. Remove two (2) guide bar nuts (A) and guide bar cover screw (B),
B
and turn saw chain tension adjustment screw (C) counterclockwise
to release tension.
D
2. Remove guide bar cover (D).
3. Remove guide bar and saw chain from gear case and sprocket.
4. Remove chain from guide bar and check guide bar for damage and
excessive or uneven wear. Replace guide bar if necessary.
C
A
5. Install chain on guide bar with cutters on top of bar facing toward
bar tip.
6. Install guide bar and chain on gear case, engaging chain with drive
sprocket (E).
7. Turn tension adjustment screw clockwise to take up slack in saw
chain.
E
D
B
8. Install guide bar cover (D), tighten guide bar nuts finger tight, and
install guide bar cover screw (B).
9. Adjust chain tension.
C
A
Download from Www.Somanuals.com. All Manuals Search And Download.
14
To Adjust Saw Chain Tension.
Tools Required: 10 mm Wrench, Screwdriver
WARNING
Always wear gloves when handling saw chain, otherwise serious
personal injury may result.
1. Loosen two guide bar nuts (A), if necessary.
2. Turn saw chain tensioner screw (B) clockwise to tighten saw chain
on guide bar. Turning screw counter clockwise will loosen saw
chain on guide bar.
B
3. Tighten guide bar nuts (A) firmly. Pull the saw chain around the
guide bar by hand. Saw chain should move freely on guide bar. If
saw chain is difficult to rotate or binds on guide bar, it is too tight.
A
4. Keep the saw chain lubricated and properly adjusted and the guide
bar nuts tightened firmly at all times.
Guide Bar Cover Cleaning
Tools Required: 10 mm Wrench, 4mm Hex Wrench
1. Remove two (2) guide bar nuts (A) and guide bar cover screw (B).
2. Remove guide bar cover (D).
B
D
3. Gently brush debris from inside guide bar cover and from around
sprocket.
4. Install guide bar cover (D), install and tighten guide bar nuts, and
install guide bar cover screw (B).
C
A
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
Po w e r Pr u n e r AT T A c h M e n T
oP e r A T o r 's MA n u A l 15
f I l I n g s a w c h a In
Level 2.
Tools Required: 4 mm (5/32 in.) round File
Flat File
Depth Gauge
30°
IMPORTANT
Dull or damaged cutters will result in poor cutting performance,
increased vibration and premature chain failure.
1
2
WARNING
Always stop engine and wear gloves when filing saw chain, other-
wise serious personal injury may result.
1. Set round file (A) in cutter at 30° angle. One fifth (1/5) of the file
should be exposed above top cutter edge.
90°
2. Keep file horizontal in cutter and file in one direction.
3
4
3. File until cutter top and side bevel edges are sharp without nicks.
4. Place depth gauge tool (B) firmly on top of cutter with .025" slot
and end against front cutter raker. File cutter raker with flat file
until flush with top of depth gauge.
5. Finish cutter sharpening by rounding front raker edge (C) with flat
file.
5
6
(TOP PLATE ANGLE)
6. Properly filed cutter is as shown.
7. Apply clean oil and rotate saw chain slowly to wash away filings.
8. If saw chain is coated or clogged with resin, clean in kerosene
then soak in oil.
TP PLATE CUTTING ANGLE)
55'
Download from Www.Somanuals.com. All Manuals Search And Download.
16
st o r a g e
Storage Hook Installation
1. Insert small end of hook into locating hole on attachment shaft.
2. Slide plastic cap onto end of attachment shaft.
sp e c If Ic a t Io n s
MODEL ---------------------------------------------------- 99944200532 POWER PRUNERTM ATTACHMENT
Length ------------------------------------------------------- 1448 mm (57.0 in.)
Width -------------------------------------------------------- 102 mm (4.0 in.)
Height ------------------------------------------------------- 146 mm (5.75 in.)
Weight------------------------------------------------------- 2.25 kg (4.97 lbs.)
Sprocket Type ---------------------------------------------- 6 tooth spur, 9.53 (3/8 in.) pitch
Drive Shaft-------------------------------------------------- 1/4 in. Flex Cable
Gear Reduction Ratio ------------------------------------- 1.5:1
Oiling System ---------------------------------------------- Automatic
Handle------------------------------------------------------- Left foam grip
Guide Bar and Saw Chain -------------------------------- 254 mm (10 in.), 9.53 mm (3/8 in.) pitch, .050 in. gauge,
91 VX -39X chain.
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
Po w e r Pr u n e r AT T A c h M e n T
oP e r A T o r 's MA n u A l 17
n o t e s
Download from Www.Somanuals.com. All Manuals Search And Download.
18
n o t e s
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
Po w e r Pr u n e r AT T A c h M e n T
oP e r A T o r 's MA n u A l 19
n o t e s
Download from Www.Somanuals.com. All Manuals Search And Download.
se r v Ic In g In f o r m a t Io n
p a r t s /s e r Ia l n u m b e r
Genuine ECHO Parts and ECHO REPOWER™ Parts and Assem-
blies for your ECHO products are available only from an Authorized
ECHO Dealer. When you do need to buy parts always have the Model
Number and Serial Number of the attachment with you. You can find
these numbers on the driveshaft model/serial number label. For future
reference, write them in the space provided below.
Model No. ______________SN._________________________
DEALER?
Call
1-800-432-ECHO
or
s e r v Ic e
Service of this product during the warranty period must be performed
by an Authorized ECHO Service Dealer. For the name and address of
the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO (3246). When presenting your unit for War-
ranty service/repairs, proof of purchase is required.
e c h o c o n s u m e r p r o d u c t s u p p o r t
If you require assistance or have questions concerning the application,
operation or maintenance of this product you may call the ECHO Con-
sumer Product Support Department at 1-800-673-1558 from 8:30 am
to 4:30 pm (Central Standard Time) Monday through Friday. Before
calling, please know the model and serial number of your unit to help
your Consumer Product Support Representative.
CONSUMER PRODUCT
SUPPORT
1-800-673-1558
8:30 - 4:30 Mon - Fri C.S.T.
w a r r a n t y r e g Is t r a t Io n
To ensure trouble free warranty coverage it is important that you regis-
tration options are by automated phone at 1-800-432-3246 or by filling
out the warranty registration card supplied with your unit. Registering
your product confirms your warranty coverage and provides a direct
link between you and ECHO if we find it necessary to contact you.
a d d It Io n a l o r r e p l a c e m e n t m a n u a l s
Replacement Operator, Safety Manuals, and Parts Catalogs are available from your ECHO dealer or at www.echo-
usa.com or by contacting ECHO Inc., 400 Oakwood Road, Lake Zurich, IL 60047 (800-673-1558). Always check the
ECHO Web Site for updated information.
Safety Videos are available from your Echo dealer. A $5.00 shipping charge will be required for each video.
ECHO, INCORPORATED
400 oa k w o o d ro a d
la k e Zu r Ic h , Il 60047-1564
w w w .e c h o -u s a .c o m
S06800001001/S06800999999
Download from Www.Somanuals.com. All Manuals Search And Download.
|