POWER BLOWER
Operator's Manual
MODEL Type 1E PB-2400
Serial Number 001001 & Up
WARNING
DANGER
Read rules for safe operation and all instructions carefully. ECHO provides this Operator's Manual
which must be read and understood for proper and safe operation.
89861009461
07/96
X7501133300
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR'S MANUAL
3
TABLE OF CONTENTS
Maintenance ........................................................... 15
- Skill Levels .................................................. 15
- Maintenance Intervals ................................. 15
- Air filter ....................................................... 16
- Carburetor Adjustment ................................ 16
- Cooling System............................................ 17
- Exhaust System ........................................... 18
- Spark Plug ................................................... 18
- Fuel Filter .................................................... 19
- Starter Rope Replacement ........................... 20
Troubleshooting ..................................................... 22
Storage .................................................................... 23
Servicing Information ............................................ 24
- Parts ............................................................. 24
- Service ......................................................... 24
- Warranty Card ............................................. 24
- Additional or Replacement Manuals .......... 24
- Manual Ordering Instructions..................... 24
Introduction .............................................................. 2
- The Operator's Manual.................................. 2
Manual Safety Symbols & Important Information .. 3
Safety ....................................................................... 4
- General Description....................................... 4
- Decals ............................................................ 4
- Equipment ..................................................... 5
- Fuel ................................................................ 5
- Personal Condition & Safety Equipment ...... 6
- Safe Operation ............................................... 7
- Extended Operation/Extreme Conditions ..... 8
Description ............................................................... 9
- Emission Control ........................................... 9
- Contents ......................................................... 9
Specifications ......................................................... 11
Assembly ................................................................ 11
- Install Blower Pipes..................................... 11
Pre-Operation ......................................................... 12
- Fuel .............................................................. 12
Operation ................................................................ 13
- Starting Cold Engine................................... 13
- Starting Warm Engine ................................ 13
- Stopping Engine .......................................... 13
- Operating Blower ........................................ 14
Specifications, descriptions and illustrative material in
this literature are as accurate as known at the time of
publication, but are subject to change without notice.
Illustrations may include optional equipment and
accessories, and may not include all standard equipment.
MANUAL SAFETY SYMBOLS & IMPORTANT INFORMATION
Throughout this manual and on the product itself, you will find safety
alerts and helpful, information messages preceded by symbols or key
words. The following is an explanation of those symbols and key
words and what they mean to you.
This symbol accompanied by the words WARNING and
DANGER calls attention to an act or condition that can lead
to serious personal injury to operator and bystanders.
IMPORTANT The enclosed message
provides information necessary for the
protection of the unit.
The circle with the slash symbol means whatever is shown
within the circle is prohibited.
NOTE This enclosed message provides tips
for use, care and maintenance of the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
SAFETY
GENERAL DESCRIPTION
IMPORTANT
See Description and Specification sections and Decals in this section for full description and illustration of
power head, and blower assembly.
HOT DECAL
DECALS
Locate these safety decals on your unit. The illustration shows their
location. Make sure the decals are legible and that you understand
and follow the instructions on them. If a decal cannot be read, a new
one can be ordered from your ECHO dealer. See PARTS ORDERING
instructions for specific information.
SPANISH DECAL
ADVERTENCIA
PELIGRO
ENGLISH TRANSLATION
GENERAL WARNING DECAL
WARNING
-WARNING-
-DANGER-
DANGER
Read and follow all safety
precautions in the operator's
manual. Operators, helpers &
bystanders can be severely
injured by blown objects and
must wear specified ANSI
Z87.1 eye protection. Always
wear hearing protection when
operating.
Esta unidad puede ser
peligrosa y producir
lesiones personales
graves si no se usa
en forma adecuada.
Para reducir el riesgo
delesionarse, los
operadores, los
This unit can be
dangerousandcause
serious injury if
improperly used. To
reduce injury risk to
operator,helpersand
bystanders,readand
understandthe
ayudantes y los
espectadores deben
leer y comprender el
Manual Del Operador
que se entrega
Operator's Manual,
which is provided in
Spanish.
escrito en español.
HOT
DECAL
GENERAL
WARNING
DECAL
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR'S MANUAL
5
EQUIPMENT
Before operation a complete check of the unit must be performed:
- Check unit for loose/missing nuts, bolts and screws. Tighten
and/or replace as needed.
- Inspect fuel lines, tank and area around carburetor for fuel leaks.
DO NOT operate unit if leaks are found.
Spark Arrestor Muffler
- The spark arrestor muffler controls the exhaust noise and prevents
hot, glowing particles of carbon from leaving the muffler. Make
sure the spark arrestor screen is in good repair and properly seated
in the muffler. (Refer to Exhaust System Maintenance pg. 18.)
Parts
ATTS
- Do not use blower if any part is missing or damaged.
- Have repairs done only by an authorized ECHO Service dealer.
- Do not use any attachment, accessory or replacement part unless it
is recommended in this Operator's Manual.
ACES
FUEL
WARNING
DANGER
Fuel is VERY flammable. Use extreme care when mixing,
storing or handling or serious personal injury may result.
-
-
-
-
Use an approved fuel container.
DO NOT smoke near fuel.
DO NOT allow flames or sparks near fuel.
Fuel tanks/cans may be under pressure. Always loosen fuel
caps slowly allowing pressure to equalize.
NEVER refuel a unit when the engine is HOT!
NEVER refuel a unit with the engine running.
DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks
outdoors over bare ground.
-
-
-
After Refueling;
- Wipe any spilled fuel from the unit.
- Move at least 3 M (10 ft.) from refueling location before starting.
After use;
- DO NOT store a unit with fuel in its tank. Leaks can occur. Return
unused fuel to an approved fuel storage container.
10'MINIMUM
Download from Www.Somanuals.com. All Manuals Search And Download.
6
PERSONAL CONDITION & SAFETY EQUIPMENT
WARNING
DANGER
Power Blower users risk injury to themselves and others if the power blower is used improperly and
or safety precautions are not followed. Proper clothing and safety gear must be worn when operating a blower.
Physical Condition --
Your judgment and physical dexterity may not be good:
- if you are over tired or sick,
- if you are taking medication,
- if you have taken alcohol or drugs.
Operate unit only if you are physically and mentally well.
Eye Protection --
Wear goggles that meet ANSI Z87.1 eye protection requirements
whenever you operate the blower.
Hand Protection --
Wear no-slip, heavy duty work gloves to improve your grip on the
blower handle. Gloves also reduce the transmission of machine
vibration to your hands. Special vibration reducing gloves such as
Echo's Pro-Comfort are designed to provide additional comfort.
Breathing Protection --
Wear a face mask to protect against breathing dust.
Hearing Protection --
Wear hearing protection. OSHA requires the use of hearing protection
if this unit is used 2 hours per day or more. ECHO recommends
wearing hearing protection whenever unit is used.
Proper Clothing --
Wear snug fitting, durable clothing;
- Pants should have long legs, shirts with long sleeves.
- DO NOT WEAR SHORTS,
- DO NOT WEAR TIES, SCARVES, JEWELRY.
Wear sturdy work shoes with nonskid soles;
- DO NOT WEAR OPEN TOED SHOES,
- DO NOT OPERATE UNIT BAREFOOTED.
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR'S MANUAL
7
Hot Humid Weather --
Heavy protective clothing can increase operator fatigue which may
lead to heat stroke. Schedule heavy work for early morning or late
afternoon hours when temperatures are cooler.
SAFE OPERATION
Setup/Check Operation Area --
-
Review area to be cleared. Look for potential hazards such as
stones or metal objects.
-
Spectators and fellow workers must be warned, and children and
animals prevented from coming nearer than 15M (50 ft.) while the
blower is in use.
-
-
Operate only in well ventilated areas: do not operate in enclosed
areas such as inside garages, sheds or buildings.
Take wind conditions into account: avoid open doors and windows.
Use Proper Clothing & Equipment
-
Before starting the unit, equip yourself and any other person
working within the 15M (50 ft.) Safety Zone with the required
Protective Equipment and clothing.
-
-
Start unit on ground with throttle at idle. Check that blower pipe
is not blocked by the ground or by any objects.
Do not point blower at people or animals.
Keep A Firm Grip & Solid Stance
-
-
Hold handle with fingers together encircling the handle.
Maintain footing and balance at all times. Do not stand on
slippery, uneven or unstable surfaces. Do not work in odd posi-
tions or on ladders.
-
Do not perform Maintenance or Assembly procedures with engine
running.
Noise Control
-
-
-
Follow local noise regulations on sound levels and hours of
operations. Use only during appropriate hours.
Never use a higher speed setting then necessary to perform a task.
The higher the engine speed the louder the blower noise.
Be a good neighbor.
Avoid Hot Surfaces
-
During operation, the exhaust area may become very hot, too hot to
touch. Avoid contact during and immediately after operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
EXTENDED OPERATION/EXTREME CONDITIONS
Vibration and Cold --
It is believed that a condition called Raynaud’s Phenomenon, which
affects the fingers of certain individuals may be brought about by
exposure to vibration and cold. Exposure to vibration and cold may
cause tingling and burning sensations followed by loss of color and
numbness in the fingers. The following precautions are strongly
recommended because the minimum exposure which might trigger the
ailment is unknown.
•
•
•
Keep your body warm, especially the head, neck, feet, ankles,
hands and wrists.
Maintain good blood circulation by performing vigorous arm
exercises during frequent work breaks and also by not smoking.
Limit the hours of operation. Try to fill each day with jobs where
operating the blower or other hand-held power equipment is not
required.
•
If you experience discomfort, redness and swelling of the fingers
followed by whitening and loss of feeling, consult your physician
before further exposing yourself to cold and vibration.
Repetitive Stress Injuries --
It is believed that overusing the muscles and tendons of the fingers,
hands, arms and shoulders may cause soreness, swelling, numbness,
weakness and extreme pain in those areas. Certain repetitive hand
activities may put you at a high risk for developing a Repetitive Stress
Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome
(CTS), which could occur when your wrist swells and squeezes a vital
nerve that runs through the area. Some believe that prolonged expo-
sure to vibration may contribute to CTS. CTS can cause severe pain
for months or even years. To reduce the risk of RSI/CTS, do the
following:
•
Avoid using your wrist in a bent, extended or twisted position.
Instead try to maintain a straight wrist position. Also, when
grasping, use your whole hand, not just the thumb and index
finger.
•
•
•
•
Take periodic breaks to minimize repetition and rest your hands.
Reduce the speed & force in which you do the repetitive movement.
Do exercises to strengthen the hand and arm muscles.
See a doctor if you feel tingling, numbness or pain in the fingers,
hands, wrists or arms. The sooner RSI/CTS is diagnosed, the more
likely permanent nerve and muscle damage can be prevented.
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR'S MANUAL
9
DESCRIPTION
EMISSION CONTROL
The emission control system for this engine is EM (Engine Modifica-
tion).
An Emission Control Label is located on the engine. (This is an
EXAMPLE ONLY, information on label varies by engine FAMILY).
IMPORTANT ENGINE INFORMATION
ENGINE FAMILY: TEH0240824RC
DISPLACEMENT: 23.6cc
THIS ENGINE MEETS U.S. EPA PH1 AND 1995-
1998 CALIFORNIA EMISSION REGULATIONS FOR
ULGE ENGINES. REFER TO OWNER'S MANUAL
FOR MAINTENANCE SPECIFICATIONS AND
ADJUSTMENTS.
KIORITZ CORP.
CONTENTS
1- Power Head
1- Blower Pipe Assembly
1- Plastic Bag
1- Operator's Manual
1- Warranty Registration Card
1- ECHO Emissions and Warranty Statement
Download from Www.Somanuals.com. All Manuals Search And Download.
10
9
6
10
7
5
1
11
2
3
4
8
3
1. AIR CLEANER - Contains replaceable felt element.
2. CHOKE LEVER - Lever is located on right side of the air cleaner. Push lever DOWN to close choke (starting
position) and for emergency stopping. Lift up to open choke (run position).
3. PURGE BULB - Pumping purge bulb before starting draws fresh fuel from fuel tank to carburetor replacing air
and old fuel. Before starting, pump repeatedly (normally 3-4 times) until fuel is visible in "Clear" fuel return
line.
4. FUEL TANK CAP - Covers and seals fuel tank.
5. BLOWER PIPES - Twist lock design.
6. IGNITION SWITCH - "SLIDE SWITCH" mounted on top of handle. Push forward to start and run. Slide
back to stop.
7. SPARK PLUG - Provides spark to ignite fuel mixture.
8. STARTER HANDLE - Pull handle slowly until starter engages, then return handle slowly. DO NOT let handle
snap back or damage to unit will occur.
9. THROTTLE TRIGGER - Spring loaded to return to idle when released if throttle lever is not engaged.
10. THROTTLE POSITION LEVER - Pull back to increase engine speed. Friction washers maintain throttle lever
setting.
11. MUFFLER/SPARK ARRESTOR - The spark arrestor muffler controls the exhaust noise while the spark
arrestor prevents hot, glowing particles of carbon from leaving the muffler.
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR'S MANUAL
11
SPECIFICATIONS
Dimensions
Length
Width
Height
340mm (13.4 in.) w/o blower pipe
215 mm (8.46 in.)
375 mm (14.75 in.)
4.3 kg (9.5 lb.)
Weight w/pipes (dry)
Engine
Type
Air-cooled, two-stroke, singlecylindergasolineengine
34.0 mm (1.34 in.)
Bore
Stroke
26.0 mm (1.024 in.)
Displacement
23.6 cc (1.44 cu. in.)
Exhaust System
Carburetor
*Sparkarrestormuffler
WALBROdiaphragmmodelWTw/purge
NGKBPM-7Y
Ignition System
Fuel System
Spark Plug
Fuel
Mixed (gasoline and oil)
50:1
Fuel/Oil Ratio
Gasoline
89 octane unleaded. Do not use fuel containing
methyl alcohol, more than 10% ethyl alcohol or 15%
MTBE.
Oil
50:1ECHOHighPerformance2-strokeengineoil
0.5 lit. (17.0 U.S. fl. oz.)
AutomaticrewindstarterCentrifugaltype
7300RPM
Fuel Tank Capacity
Starter System
Wide Open Throttle Speed
Idle Speed
2500 - 3000 RPM
Max Air Volume
Max Air Speed
300 cu. ft./min
w/pipes
150MPH
* Certain internal combustion engines operated in forest, brush and/or grass-covered areas in Washington, Oregon,
Idaho, California, Minnesota, New Jersey and Maine must be equipped with a spark arrestor. This requirement also
applies to all U.S. Forest Service lands. In some of these areas, the spark arrestor system must be certified per USDA
Forest Service regulations SAEJ335. Check with your local or state authorities for specific regulations in your area.
Failure to follow these requirements is a violation of the law.
ASSEMBLY
WARNING
DANGER
Never perform maintenance or assembly procedures with
engine running or serious personal injury may result.
INSTALL BLOWER PIPES
1. Align grooves in straight pipe with pegs on blower housing and
slide pipe onto housing.
2. Turn straight pipe clockwise to lock it into place.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
PRE-OPERATION
FUEL
Fuel Requirements --
Gasoline - Use 89 Octane [ R + M ] gasoline known to be good quality.
2
Gasoline may contain up to 10% Ethanol (grain alcohol) or 15%
MTBE (methyl tertiary-butyl ether). Gasoline containing methanol
(wood alcohol) is NOT approved.
Two Stroke Oil - A two-stroke engine oil meeting proposed ISO-L-
EGD Standard (ISO/CD 13738), must be used. Echo brand Premium
50:1 oil meets this proposed standard. Engine problems due to
inadequate lubrication caused by failure to use an ISO-L-EGD
approved oil, such as Echo Premium 50:1 Two-stroke Oil, will void
the two-stroke engine warranty. (Emission related parts only are
covered for two years, regardless of two-stroke oil used, per the
statement listed in the EPA Phase I/California Emission Defect
Warranty Explanation.)
Mixing - Follow directions on the oil container.
Handling Fuel --
WARNING
DANGER
Fuel is VERY flammable. Use extreme care when mixing,
storing or handling or serious personal injury may result.
- Use an approved fuel container.
- DO NOT smoke near fuel.
- DO NOT allow flames or sparks near fuel.
- Fuel tanks/cans may be under pressure. Always loosen fuel
caps slowly allowing pressure to equalize.
- NEVER refuel a unit when the engine is HOT!
- NEVER refuel a unit with the engine running.
- DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks
outdoors over bare ground.
10'MINIMUM
After Refueling -
-
-
Wipe any spilled fuel from the unit.
Move at least 3M. (10 ft.) from refueling location before starting.
After use -
DO NOT store a unit with fuel in its tank. Leaks can occur. Return
unused fuel to an approved fuel storage container.
-
S M T W T F
S
7
1
8
2
3
4 5 6
Storage -
9 10 11 12 13 14
Fuel storage laws vary by locality. Contact your local government for
the laws affecting your area. As a precaution, store fuel in an ap-
proved, air tight container. Store in a well ventilated, unoccupied
building, away from sparks and flames. Do not store fuel longer than
30 days.
15 16 17 18 19 20 21
22 23 24 25 26 27 28
29 30 31
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR'S MANUAL
13
A
OPERATION
IMPORTANT
Check unit for loose nuts, bolts and screws daily.
IMPORTANT
Recoil starter: Use short pulls - only 1/2-2/3 of rope length for
starting. Do not allow the rope to snap back in. Always hold
the unit firmly.
STARTING COLD ENGINE
1. Move ignition switch (A) to START/RUN position.
2. Push purge bulb (B) 3-4 times (or until fuel is visible in fuel return line).
3. Close choke (C) (move choke lever down) and pull starter handle
(D) until engine fires.
C
4. Open choke (C) and if necessary, restart engine.
B
D
NOTE
Allow engine to warm up before use.
STARTING WARM ENGINE
1. Move ignition switch (A) to start, pull starter handle (D) 1-3
times and engine should start. Do not use choke (C).
C
NOTE
If engine does not start after 3 pulls, use cold start procedures.
D
D
STOPPING ENGINE
1. Release throttle trigger (E) and allow engine to run at idle for a
few minutes.
A
2. Move ignition switch (A) to "STOP" position.
E
WARNING
DANGER
If engine does not stop, shift choke lever to closed position.
Check and repair ignition switch before starting engine again or
serious personal injury may result.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
OPERATING BLOWER
WARNING
DANGER
F
Always wear safety glasses, hearing protection and a face filter
mask or serious personal injury may result.
Do not point the blower pipe in the direction of people or pets.
Read the Safety Section carefully.
IMPORTANT
To avoid engine damage due to over revving, do not block
blower pipe.
1. Use only during appropriate hours.
2. Make sure bevel at end of pipe faces downward.
3. Allow the engine to warm up at a fast idle for a few minutes.
4. Set engine speed with throttle position knob (F). Rotate lever
forward for lower speed; downward for higher speed.
NOTE
The PB-24LN can be run at any speed between 2500 RPM to 7300
RPM once the engine has broken in (approximately after 3 fuel
tanks).
NOTE
Use lower speed to blow dry leaves from a lawn or flower bed.
Additional speed may be necessary to clean grass and leaves from
walks, patios and drives or to move gravel, dirt, snow, bottles or
cans from a driveway, street, parking lot or stadium.
NOTE
Never use a higher speed setting than necessary to perform a task.
Remember, the higher the engine speed, the louder the blower
noise. Minimize dust by using blower at lower speeds. Keep debris
on your property.
Be Smart - be a good neighbor.
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR'S MANUAL
15
MAINTENANCE
Your ECHO blower is designed to provide many hours of trouble free service. Regular scheduled maintenance will help
your blower achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take your
unit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have
the ECHO Dealer do it, each maintenance task has been graded.
Level 1 = Easy to do. Most required tools come with unit.
Level 2 = Moderate difficulty. Some specialized tools may be required.
Level 3 = Experience required. Specialized tools are required.
ECHO offers REPOWER Maintenance Kits and Parts to make your maintenance job easier. Just below each task
heading are listed the various part numbers required for that task. See your ECHO dealer for these parts.
MAINTENANCE INTERVALS
Six
Months
or 300
Three
Months
or 100
Component/System
Maintenance
Procedure
Before
Use
Every
Refuel
Daily or Every
4 hours
Yearly or *Date Main-
600 hours
tenance
Performed
hours
hours
•
•
AirFilter
Clean
Replace
•
•
•
FuelStrainer
FuelLine
Clean/Replace
Inspect
•
Carburetor
Inspect/Rebuild
Replace
• (1)
•
ChokeSystem
CoolingSystem
Inspect/Clean/Replace
Inspect
•
•
•
•
Clean
•
•
MufflerSparkArrestor
Inspect
Clean
•
•
•
StarterRope
FuelLeaks
Inspect/Clean
Inspect
Repair
•
SparkPlug
Clean
•
Replace
No Maintenance required for coil and flywheel
IgnitionSystem
Clean/Replace
Inspect/Tighten/Replace
•
Screw/Bolts/Nuts
IMPORTANT
Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance.
*Record dates of monthly and yearly inspections.
(1) Replacement will be required for Commercial use after 600 hours. For Consumer use, cleaning every 6 months is
required. Cleaning includes Rebuild Kits.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
AIR FILTER
Level 1.
Tools required: Cleaning brush, 1" or 2" medium bristle paint brush.
Parts required: Part Number 13031051830 Air Filter.
NOTE
Clean daily.
1. Close choke, remove wing nut, air cleaner cover and air filter.
2. Brush dust off filter and wash in suitable solvent.
3. Dry filter before reinstalling.
ADJUSTING CARBURETOR - GENERAL
Level 2.
Tools required: Screwdriver, Tachometer (P/N 99051130017).
Parts required: none.
NOTE
Do not adjust carburetor unless necessary. If you have difficultly,
see your ECHO dealer.
Adjustment Screws
Idle Speed (A)
Control throttle opening at idle.
Low (LO) Speed (B) Controls amount of fuel at low speed and
supplementary fuel for smooth progression from
idle to high speed.
Hi (HI) Speed (C)
Controls amount of fuel at full throttle
C
B
Before Adjustment
Check that:
- Air filter is clean and properly installed.
- Spark arrestor screen and exhaust port are free of carbon
- Blower pipes are installed
Initial Adjustment
A
1. With engine off, turn HI speed screw counterclockwise to stop.
2. Turn LO speed midway between stops.
3. Turn idle screw until tip of screw just touches throttle plate; then
turn three (3) turns clockwise.
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR'S MANUAL
17
Final Adjustment
IMPORTANT
B
Limiter caps prevent exceeding C.A.R.B. and E.P.A. emission
limits and over rich adjustment, but not over lean adjustment,
which can cause engine failure: Do not exceed recommended
HI speed engine R.P.M. during operation, or for long periods
during adjustment.
1. Start engine, run at idle for one minute.
A
2. Complete warm up by running at full throttle for 5 minutes,
operating choke twice to clear air from carburetor chambers.
3. Run at idle and accelerate to check for smooth transition from
idle to high speed; if engine hesitates, turn LO speed screw (B)
counterclockwise 1/8th of a turn at a time until acceleration is
smooth.
4. Adjust idle screw (A) to 3000 R.P.M., using tachometer.
COOLING SYSTEMS
Level 3.
Tools required: 3/4" Spark Plug deep socket, 3 MM Allen wrench,
Phillips Screwdriver, Pointed Wood Stick, Cleaning Brush, 1"-2"
medium bristle paint brush.
Parts Required: None if you are careful.
IMPORTANT
To prevent overheating and engine seizure, cooling air comes
through the grille and is pushed by a cooling fan through the
cylinder fin area to an opening in the front of the engine cover,
taking away combustion heat. The grille and cylinder fins must
be kept clean of grass, dust and any debris. Engine failure due to
lack of this "Normal Maintenance" is not covered by warranty.
A
Cleaning Grill
Remove accumulated debris from crankcase intake grille (A) above the
fuel tank.
Cleaning Cylinder Fins
1. Remove spark plug.
2. Remove engine cover (three screws) and clean cylinder fins to
allow cooling air to pass freely.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
EXHAUST SYSTEM
Level 3.
Tools Required: Phillips Screwdriver, 4mm Allen wrench, Soft metal
brush. Wooden carbon scraper.
Parts Required: Spark arrestor screen P/N 14586240630, gasket P/N
14586642031.
Muffler and Exhaust Port
IMPORTANT
Carbon deposits in cylinder exhaust port and muffler will cause a
drop in engine output and overheating. Muffler exhaust port and
spark arrestor screen must be checked periodically.
1. Remove spark plug and engine cover (three screws).
2. Remove muffler (D).
3. Clean cylinder exhaust port being careful not to scratch cylinder
or piston, using a wooden or plastic scraper.
C
4. Remove spark arrestor cover (A), gasket (B) and spark arrestor
screen (C) from muffler. Replace screen if plugged with carbon
deposits.
5. Install spark arrestor screen, gasket, and cover.
6. Be sure gasket seals muffler spark arrestor screen to muffler.
B
D
A
SPARK PLUG
Level 2.
Tools Required: 3/4" Spark Plug deep socket, Feeler gauge. Prefer-
ably a wire gauge.
Parts Required: Spark Plug, NGK BPM-7Y, P/N 99944500071
1. Remove spark plug and check for fouling, worn and rounded
center electrode.
2. Clean the plug or replace with a new one. DO NOT sand blast to
clean. Remaining sand will damage engine.
3. Adjust spark plug gap by bending outer electrode.
0.65 mm
(0.026 in.)
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR'S MANUAL
19
FUEL FILTER
Level 1.
Tools required: Fuel line hook. 203-254 mm (8"-10") length of wire
with one end bent into a hook. Clean cloth, funnel, and an approved
fuel container.
Parts required: Part Number 13120514930
NOTE
Check fuel strainer periodically.
IMPORTANT
Keep fuel tank clean - do not allow dirt or debris to enter fuel
tank.
NOTE
A clogged fuel strainer will cause hard starting or poor engine
performance.
1. Pick up the fuel filter through fuel tank opening with a piece of
steel wire.
2. Remove old filter.
3. Install new filter.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
STARTER ROPE REPLACEMENT
Level 3.
Tools required: SAFETY GOGGLES, Screwdriver, 3mm Allen
wrench.
Parts Required: 890 mm (3.5 in) ECHO Starter Rope, Lithium based
grease.
1. Remove four (4) screws holding starter assembly on engine,
remove starter.
2. Hold starter drum in place and cut off or untie knot (A). Allow
the drum to slowly turn until all spring tension is relieved.
WARNING
DANGER
The spring inside the starter is under tension. DO NOT remove
screw (B) until spring tension is relieved or serious personal
injury may result.
A
B
IMPORTANT
The spring must not come out with the drum. If resistance is felt
when lifting the drum, STOP! See your Authorized ECHO
Service Dealer for help.
3. Remove screw (B), turn drum slightly clockwise and lift carefully
and slowly.
4. Remove the old starter rope and prepare the new rope by first
heating both ends to prevent fraying.
5. Pass one end of the rope through the opening of the drum and tie
a knot. Press knot and end of rope in cavity of drum.
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR'S MANUAL
21
6. Thread the rope through the eyelet in the housing (C) then
through the starter handle (D). Follow the illustration and tie
another knot in the free end of the rope. Pull the knot into the
handle.
D
C
7. Check that the hook (E) on the end of the spring touches the post
(F). Lightly grease the top of the spring and the post.
F
E
8. Hold the drum pawl side up and wind the rope on the drum
counterclockwise, four (4) turns.
9. Install drum. The loop in the spring must engage the slot in the
drum. Replace the screw and washer.
10. Hold the rope in the notch (G) and rotate the drum counterclock-
wise several turns.
11. Hold the drum to prevent it from rewinding, pull the excess rope
taught with the handle and allow to rewind slowly.
12. Pull rope several times to check spring tension. If rope does not
rewind fully, repeat 10.
G
13. Pull rope out all the way. Drum must be able to turn an addi-
tional 1/2 turn counter clockwise. If drum does not turn, see your
Authorized ECHO Service Dealer.
14. Install starter and test.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
TROUBLESHOOTING
Problem
Engine
starts hard
does not start
Remedy
Cause
Engine
Cranks
Fuel at
carburetor
Clean
Clean
See your Echo dealer
Fuel strainer clogged
Fuel line clogged
Carburetor
No fuel at
carburetor
See your Echo dealer
Carburetor
Fuel at
cylinder
No fuel at
cylinder
Open choke
Muffler wet
with fuel
Fuel mixture is too rich
Clean/replace air filter
Adjust carburetor
See your Echo dealer
Turn switch on
See your Echo dealer
See your Echo dealer
Spark at
end of
plug wire
No spark at end
of plug wire
Ignition switch off
Electrical problem
Interlock switch
Spark gap incorrect
Covered with carbon
Fouled with fuel
Adjust. 0.65 mm(0.026 in.)
Clean or replace
Clean or replace
No spark at plug
Spark at
plug
Spark plug defective
Replace plug
Engine
does not
crank
See your Echo dealer
Internal engine problem
Engine
runs
Dies or
Accelerates poorly
Air filter dirty
Fuel filter dirty
Fuel vent plugged
Spark plug
Carburetor
Clean or replace
Replace
Replace
Clean and adjust/replace
Adjust
Cooling system plugged
Exhaust port/spark
arrestor screen plugged
Clean
Clean
Engine Blower does not work,
Blower Pipe clogged,
loose, or damaged
Unclog
Tighten
Replace
runs
is weak or uneven
properly
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER BLOWER
OPERATOR'S MANUAL
23
STORAGE
Long Term Storage (Over 30 Days)
Do not store your unit for a prolonged period of time (30 days or
longer) without performing protective storage maintenance which
includes the following:
1. Store unit in a dry, dust free place, out of the reach of children.
WARNING
DANGER
Do not store in enclosure where fuel fumes may accumulate
or reach an open flame or spark or serious personal injury
may result.
2. Place the ignition switch (A) in the "STOP" position.
A
3. Remove accumulation of grease, oil, dirt and debris from exterior
of unit.
E
4. Perform all periodic lubrication and services that are required.
5. Tighten all screws and nuts.
6. Drain the fuel tank completely and pull the starter handle
several times to remove fuel from the carburetor.
7. Remove the spark plug and pour 1/4 oz. (1/2 tablespoon) of
fresh, clean ECHO 2-stroke engine oil into the cylinder through
the spark plug hole.
A. Place a clean cloth over the spark plug hole.
B. Pull the recoil starter handle 2-3 times to distribute the oil
inside the engine.
C. Observe the piston location through the spark plug hole.
Pull the recoil handle slowly until the piston reaches the top
of its travel and leave it there.
8. Install the spark plug (do not connect ignition cable).
9. Remove blower pipe assembly from unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING INFORMATION
PARTS
Genuine ECHO Parts and ECHO Re Power Parts and Assemblies for
your ECHO products are available only from an Authorized ECHO
Dealer. When you do need to buy parts always have the Model
Number, Type number and Serial Number of the unit with you. You
can find all three numbers on the engine housing. For future refer-
ence, write them in the space provided below.
Model No. _____________ Type No. ____________ SN. __________
SERVICE
Service of this product during the warranty period must be performed
by an Authorized ECHO Service Dealer. For the name and address of
the Authorized ECHO Service Dealer nearest you, ask your retailer or
call: 1-800-432-ECHO. When presenting your unit for Warranty
service/repairs, proof of purchase is required.
DEALER?
Call
1-800-432-ECHO
WARRANTY CARD
This card is our means of registering all original owners of ECHO
equipment. The card plus proof of purchase provides you the assur-
ance that authorized warranty work will be done. It also provides a
direct link between you and ECHO if we find it necessary to contact
you.
ECHO Incorporated
400 Oakwood Road
Lake Zurich, IL 60047
ADDITIONAL OR REPLACEMENT MANUALS
Operators and Parts Manuals are available for purchase from your
ECHO dealer or directly from ECHO. [See ordering instructions at
the end of this manual.]
Technical Publications Orders
ORDERING INSTRUCTIONS
To obtain a Parts Catalog or Operator's Manual send a check or money order for $2.00 per Parts Catalog or $1.50 per Operator's
Manual made payable to ECHO, INCORPORATED. State on a sheet of paper model number and serial number of the ECHO
unit you have, part number of the manual (if known), your name and address and mail to address above:
Available Parts Lists
PB-2400Type1E
S/N001001&UP
PartNumber 99922202730
ECHO, INCORPORATED
400 Oakwood Road
Lake Zurich, IL 60047
Download from Www.Somanuals.com. All Manuals Search And Download.
|