Earthquake Sound Stereo Amplifier 16IR User Manual

Cinénova IR16  
8-ZONES MULTI-SOURCE  
IR DRIVEN AMPLIFIER  
USER’S MANUAL  
Earthquake Sound Corporation  
2727 McCone Avenue. Hayward, CA 94545  
Phone: 510-732-1000  
Fax: 510-732-1095  
Sound That Will Move You.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cinénova-IR16 Power Amplifier  
Table of Content  
Getting Started  
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5  
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
6
7
Basic Operations  
Front & Rear Panel Overview . . . . . . . . . . . . . . . . . . . . . . . . . .  
8
9
Front Panel Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
Rear Panel Map - LOCAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Rear Panel Map - BUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Keypad & Remote Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Features Explained . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
IR Wiring Configuration Sample . . . . . . . . . . . . . . . . . . . . . . . . 15  
Recommended Configuration . . . . . . . . . . . . . . . . . . . . . . . . 16  
Specifications  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Troubleshooting & Maintenance  
Troubleshooting & Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 18  
Product Warranty  
Product Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Earthquake Sound  
Safety Instructions  
Safety First  
This documentation contains general safety, installation, and operating instructions for the Cinénova-IR16 Amplifiers. It is  
important to read this users’ manual before attempting to use these products. Pay particular attention to the safety  
instructions.  
Symbols Explained:  
Appears on the component to indicate the presence of uninsulated, dangerous voltage inside the enclosure –  
voltage that may be sufficient to constitute a risk of shock.  
Calls attention to a procedure, practice, condition or the like that, if not correctly performed or adhered to, could result  
in injury or death.  
Calls attention to a procedure, practice, condition or the like that, if not correctly performed or adhered to, could result  
in damage to or destruction of part or all of the product.  
Note:  
Calls attention to information that is essential to highlight.  
© 2008 Earthquake Sound Corporation. All rights reserved.  
This document should not be construed as a commitment on the part of Earthquake Sound Corporation. The information is subject to change without notice.  
Earthquake Sound Corporation assumes no responsibility for errors that may appear within this document.  
The Sound That Will Move You.  
Earthquake Sound Corporation  
2727 McCone Avenue  
Hayward, CA 94545  
Tel: 510-732-1000  
Fax: 510-732-1095  
Customer Support  
Tel: 800-576-7944  
Fax: 510-732-1095  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cinénova-IR16 Power Amplifier  
Safety Instructions  
Important Safety Instructions  
1) Read these instructions in their entirety.  
10) Protect the power cord from being walked on or pinched,  
particularly at plugs, convenience receptacles, and the pint  
where they exit from the apparatus.  
2) Store this manual and packaging in a safe place.  
3) Heed all warnings.  
11) Only use attachments & accessories specified by the  
manufacturer.  
4) Follow instructions (do not take short cuts).  
5) Do not use this apparatus near water.  
6) Clean only with a dry cloth.  
12) Use only compatible rack or cart for final resting position.  
13) Unplug this apparatus during lighting storm or when unused  
for long period of time.  
7) Do not block any ventilation openings. Install in accordance  
with the manufacturers instructions.  
14) Refer all servicing to qualified service personal. Servicing is  
required when the apparatus has been damaged in any way  
such as; power-supply cord or plug is damaged, liquid has  
been spilled or objects have fallen into the apparatus, the  
apparatus has been exposed to rain or moisture, does not  
operate normally, or has been dropped.  
8) Do not install near any heat sources such as radiators, heat  
registers, stoves, or other apparatuses that produce heat.  
9) Do not defeat the safety purpose of the polarized or  
grounding-type plug. A polarized plug has two blades with  
one wider that the other. A grounding-type plug has two  
blades and a third grounding prong. The wide blade or the  
third prong is provided for your safety. If the provided plug  
does not fit into your outlet, consult an electrician for  
replacement of the obsolete outlet.  
15) To reduce the risk of fire or electric shock, do not expose  
this apparatus to rain or moisture.  
This triangle, which appears on your component,  
This triangle, which appears on your component,  
alerts you to important operating and  
maintenance instructions in this  
alerts you to the presence of uninsulated,  
dangerous voltage inside the enclosure -  
CAUTION  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
voltage that may be sufficient to  
constitute a risk of shock.  
accompanying literature.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Earthquake Sound  
Introduction  
About Cinénova-IR16  
The Cinénova-IR16 is the second generation in multi-zone that Earthquake has produced. Thanks to the feedbacks received from custom home  
installers worldwide, we have managed present you with a truly powerful yet audiophile multi-zone amplifier with the following features:  
!
Bridgeable output  
Zone IR control with digital pad in each zone (included)  
Décor friendly keypad  
Four (4) built-in IRrepeaters  
Rear gain control limiter which limits the output gain of the zone pad.  
Each zone has a LOCAL/BUS input audio selector  
12V DC trigger  
!
!
!
!
!
!
!
Individually driven amplifier blocks (each block is driven by a discrete complementary output classA/Bstage with selected components)  
Individual power supplies(bifilars) for power isolation, accuracy and better channel separation  
!
There is no other multi-zone amplifier on the market with such features and power. Enjoy.  
Over the years, many of you have provided us with design requirements, new product development ideas and tremendous  
feedback that helped us to improved our products. We are very grateful for your support and feedback.  
From all of us here at Earthquake Sound Corporation: Thank you.  
Professor Joseph J. Sahyoun  
President & Chief Engineer  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cinénova-IR16 Power Amplifier  
Unpacking  
Connection tips  
Unpacking system components  
!
Keep the original carton and packing materials for future  
shipment or storage.  
!
It is recommended that the Cinénova-IR16 and the source  
equipment be plugged into a dedicated 20-amp circuit with an  
isolated ground.  
! Check for any visual signs of damage. If you encounter any  
concealed damage, consult your Earthquake Sound dealer  
before proceeding with unit installation.  
!
!
Disconnect all live power cords before making connections to the  
remote gain.  
! Retain the sales receipt as it established the duration of the  
limited warranty and provided information for insurance  
purposes.  
Keep all power cords away from all signal cables to prevent  
humming from induced noise.  
! Choose reliable signal cables cords (Earthquake Sound also  
Cinénova-IR16 included components  
• 1 Power cord  
specializes in high-performance RCA cables and patches).  
• 8 Remote controls  
! All speaker wires that are ran through the walls should be twisted  
• 8 Keypads (wallplates not included)  
• 8 Phoenix speaker terminals  
• 8 Phoenix pad connectors  
• 1 16-channelAmplifier  
type to reduce potential hum noise pick up.  
! Label both ends of all wires with the corresponding room  
location.  
! It is best to use a grounded electrical outlet to power the  
amplifier. Lack of input ground reference could be unsafe.  
Consult with your electrical contractor about proper grounding.  
System installation considerations  
There are several factors to consider before installing the Earthquake  
Sound Cinénova-IR16 system.  
• What are the intended listening zones?  
• What system options and accessories might be required for  
features such as local sources, etc.?  
• From where in each zone will the listener prefer to control the  
system? Where will the remote gains be located? Where will the  
speakers be located?  
• Where will the source equipment be located?  
Note: The Cinénova-IR16 must have adequate ventilation above and  
below for air circulation and heat dissipation. In addition, rack mount  
locations may require fans and vents.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Earthquake Sound  
Front & Rear Panel Overview  
19” (482.6mm)  
13  
14  
15  
16  
9
5
6
7
8
1
2
3
4
10  
11  
12  
Cinénova  
16  
IR  
C to C 18.375” (466.5mm)  
17” (431mm)  
L
R
L
L
L
L
L
L
R
R
R
R
L
L
R
R
L
R
R
R
SPEAKER OUTPUT  
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
FUSE  
110-120VAC-60Hz  
220-240VAC-50Hz  
M
M
M
M
M
M
M
M
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cinénova-IR16 Power Amplifier  
Front Panel Map  
Front Panel  
13  
14  
15  
16  
9
5
6
7
8
1
2
3
4
10  
11  
12  
Cinénova  
16  
IR  
3
1
2
1 Power/StandbySwitch  
This red colored LED indicates whether the amplifier is ONor OFF. When the amplifier is ON, this LED will be lit.  
Note: When using the rear 12V DCTrigger (page 11 -feature 11), this front switch must be turned OFF.  
2 FrontPanelPowerLED  
This LED reflects the power statusof the whole amplifier.Amplifier will not have any output unless this LED is ON.  
Note: When using another device to turn on the Cinénova IR16 amplifier, this LED will come on when external device sends DC signal (between 5 and 28V  
DC) tothe back ofTrigger connector (page 11 -feature 11).  
Peak LEDIndicators  
Each LED represents one (1) channel.This particular model has sixteen (16) channels.Thus, there are sixteen (16) LEDs located on the front panel.  
3
(!) Cinénova IR16 can be mounted in a standard rack mount (4 rack spaces).  
(!) Mounting Dimensions: 4” center to center vertical and 18.37” center to center wide.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Earthquake Sound  
Rear Panel Map - LOCAL  
1 Level Controls  
This feature adjusts the maximum desired output of the associated zone to prevent overpowering of small  
speakers.  
Note:This knob is by-passed when itszone selector switch(feature 2) is set toBUS.  
1V  
1
2
LEVEL  
3V  
0.2V  
2
LOCAL/BUSSwitch  
It switches the audio source between LOCALand common BUS. In LOCALmode, the zone acts independently  
from the rest of system by only amplifying the information fed through the associated RCAinputs. In BUS mode,  
that particular zone will amplify the signal fed through the main BUS input (page 11 -feature 9).  
LOCAL  
BUS  
3 AudioRCAInput  
Individual stereo RCA inputs to drive signal into associated zones. Both RCA’s, LEFT and RIGHT, are active  
when the STEREO/MONOswitch is set toMONO(feature 4).Thus, you can use either RCAinputs.  
Note: This RCA input also serves as an Auto Signal Sensing whenever there is a signal greater than 12mV  
present.  
3
4
1
STEREO  
MONO  
IR IN  
4
5
STEREO/MONOSelector  
Switches the amplifier’soutput between STEREOor MONO.  
·In STEREO mode, the LEFT and RIGHT outputs operate independently at 75 Watts per channel at 4Ù  
speaker load. Level, Gain,AutoTurn ONand MUTEare all common toboth.  
·In MONO mode, the LEFT and RIGHT stereo signals are summed internally for a single high power output.  
You can drive two 4Ù speakers in this mode or a single 4Ù Bridged for maximum power of 150WRMS.Also, if  
the source is already a mono signal, you may use either RCA, LEFTor RIGHT.  
STATUS  
GROUND  
CI  
5
Keypad/ZoneConnector  
With four (4) removable conductors (IR IN, STATUS, GROUND and CI–Control Input), these screw type  
connector accepts wire sized from 24 to 12 AWG. We recommend using the CAT5, CAT5E, CAT6 or CAT6E  
wires.  
·IR IN – receive all types of IR signal transmitted through the Earthquake Keypad. It allows Volume up/down  
and mute function at the local amplifier. Also, it allows most IR signal to pass through the four built-in IR  
repeaters of the Cinénova 16IR (page 11 -feature 12).  
6
7
FFI  
FFI  
BRIDGE  
·STATUS – this connector delivers DC signal to the Keypad’s LED status indicator when the associated  
amplifier is ON.  
·GROUND – forthe Keypad.  
·CI– Control Input is the communicator line used tocontrol amplifier’sON/OFF(Mute) statusmanually.  
6
7
FaultFuseIndicator(FFI)  
This LED indicates the safe operation of the amplifier’s internal circuit for the associated zone. Under normal  
condition, this LED is off. When it is lit, the fuse on the internal circuit of that associated zone is blown, usually  
due to a shorted circuit. Simply replace with the same size fuse. For your convenience, we’ve included four (4)  
additional fuses with every amplifier.  
L
R
L
L
L
L
L
L
R
R
R
R
R
L
L
L
R
R
R
R
SPEAKER OUTPUT  
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
Speaker Terminals  
This screw type connector with four (4) removable conductors accepts wire sizes from 16 to 12AWG. Observe  
the Polarity printed on the terminal. Observe the printed instruction above and below the Speaker terminal.  
FUSE  
110-120VAC-60Hz  
220-240VAC-50Hz  
M
M
M
M
M
M
M
M
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cinénova-IR16 Power Amplifier  
Rear Panel Map - BUS  
8 CommonBUS LevelController  
This potentiometer controls the output level on all individual amplifiers that are switched to BUS mode. It also  
actsas a volume limiter toprotect the speakers and amplifier itself.  
1V  
9 CommonBUSAudioRCAInput  
LEVEL  
8
9
This pair of RCAdrives a stereo signal into all zones that are switched to BUS mode. It allows one (1) source to  
control as many as 8 zonesaudio out.  
3V  
0.2V  
BUS  
10 RCALineOut  
This allows the audio signal applied to the BUS RCA inputs to pass through unaltered to another device in the  
system.  
10  
11  
11 12V DC Trigger  
LINE OUT  
It is the remote turn on option driven by a controlled 12V DC source or anAC/DC converter. The relay operating  
range is between 5V DC and up to 28V DC. This remote turn on option does not override the auto signal sensing  
turn on feature of this amplifier.  
Note: The front power switch (page 9 - feature 1) must be left in the OFF position in order to for this function to  
+12VDC  
TRIGGER  
work.  
12  
1
3
2
4
IROutputs  
Four (4) amplified IRrepeaters torepeat signals and commends fed through individual Earthquake Keypads.  
IR OUT  
12  
13  
PowerConnection  
This three (3) prongAC line connector is factorypreset to120VAC. However, other voltages are also available.  
14  
MainPowerFuse  
Always replace the protection fuse with a similar value fuse. Please follow the fuse rating below:  
115V,T15AL/250V  
230V,T10AL/250V  
13  
14  
FUSE  
110-120VAC-60Hz  
220-240VAC-50Hz  
L
R
L
L
L
L
L
L
R
R
R
R
R
L
L
L
R
R
R
R
SPEAKER OUTPUT  
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
FUSE  
110-120VAC-60Hz  
220-240VAC-50Hz  
M
M
M
M
M
M
M
M
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Earthquake Sound  
Keypad & Remote Map  
1 LEDStatus  
This red colored LED indicates whether the amplifier is ONor OFF. When the amplifier is ON, this LED will be lit.  
2 VolumeUp/Down  
This allows you to manually control the volume level up or down. The volume increases and decreases at the  
same rate.  
Note: This amplifier will hold the user defined volume setting for up to 3 hours from the last shut down.  
Otherwise, the amplifier will start with volume position set to minimum to prevent undesired loud music in  
unattended areas.  
1
2
3
4
3
4
Mute  
This allows you tomute or un-mute the associated amplifier(s) output.  
IRReceiver  
This feature allows the communication of all IR information between the Keypad and the rest of the system.  
Coded signal controls the individual volume at each channel while other IR information can pass through  
unaltered tothe rest of the components connected tothe provided IRout repeaters (page 11 -feature 12).  
Note: Wallplates are not included  
(!) NOTE: One Keypad is capable of driving multiple zones. Simply connect the CI wire of those zones in  
parallel. For example, if you want to use the Keypad from zone 1 to control zone 1 through 5, remove the  
Keypad connecting wires from zone 2 through 5 and parallel the CI wire of zone 2 through 5 to the CI of  
zone1.  
(!) NOTE: If a zone is not connected to a Keypad, the speaker output will be muted (no audio output to  
thespeaker) unlessyouparallelconnectthatzone’s CIwiretoanotherzone’s CI.  
KEYPAD  
1
KEYPAD KEYPAD KEYPAD  
8
7
6
ZONE  
1
ZONE  
2
ZONE  
3
ZONE  
4
ZONE  
5
ZONE  
7
ZONE  
8
ZONE  
6
MUTE  
1
VOL+  
VOL-  
2
In addition to the eight (8) Earthquake Keypads, we also provide you with remote controls that have the same  
functions – Volume Up/Down and Mute. For your convenience, the remote information can be taught to any  
remote with learning capability.  
1 Mute  
This allows you tomute or un-mute the associated amplifier(s) output.  
2 VolumeUp/Down  
This allows you to manually control the volume level up or down. The volume increases and decreases at the  
same rate.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cinénova-IR16 Power Amplifier  
Special Features  
Special Features  
Eightindividualpowersupplies:  
Rack mountable:  
This amplifier is designed to conveniently mount in commonly  
The Cinénova-IR16 is designed with 8 individual power  
supplies(bifilar) for power isolation, accuracy and better channel  
separation.  
used racks.  
Peak LEDindicators:  
110VAC and220VAC selectable:  
The Cinénova-IR16 is equipped with 16 LED indicators on the  
front panel. They show the operating status of each channel; the LEDs  
will illuminate when the maximum recommended output is exceeded.  
If an LED is illuminated the majority of the time, it indicates that the  
corresponding channel is over-driven (clipped). The input to the  
channel must be reduced to eliminate distortion and eventually,  
damages tothe amplifier.  
The Cinénova-IR16 is factory preset to 110-120VAC. However,  
it can also be set to accommodate 220-240VAC by Earthquake  
authorized technician(s)/dealer(s).  
Remote zonecontrol:  
Each of the eight possible zones can be controlled by a wireless  
IR remote control. Each remote has the ability to control volume’s  
up/down level, mute and also repeat the IRsignal toother sources.  
Thermal protection:  
Each channel is equipped with a thermal sensor designed to  
shut the amplifier down when it overheats. Overheating is not typical. It  
only occurs if the amplifier is over driven with low impedance speakers,  
or if the amplifier is located in an improperly ventilated space.  
Bus input:  
This feature simplifies installation by consolidating several  
channels for one source. Simply plug the input source RCAs into the  
BUS input on the unit. Then switch the input source selector to BUS for  
as many channels are connected tothe corresponding input source.  
Individuallyselected andmatched components:  
Components used to construct the Cinénova-IR16 are  
subjected to an exhaustive selection process; during which, the  
components are matched and individually tested to exact tolerance.  
The multi-layer, glass-epoxy, double sided printed circuit boards  
exceed the standard stringent requirements by 50%.  
Bridgeablefunction(minimumimpedance =4-ohm):  
The Cinénova-IR16 delivers up to 8-zones, and can be bridged  
into several different configurations forhigher power rooms.  
4 or8-ohmcompatible:  
8-Zones:  
Since speakers are manufactured in several different  
impedance ratings, Earthquake Sound’s Cinénova-IR16 amplifier is  
designed tobe 4 and 8-Ohm compatible.  
The Cinénova-IR16 delivers up to 8-zones, and several other  
room combinations tobetter suite the your needs.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Earthquake Sound  
Features Explained  
L
R
L
L
L
L
L
L
R
R
R
R
L
L
R
R
L
R
R
R
SPEAKER OUTPUT  
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
FUSE  
110-120VAC-60Hz  
220-240VAC-50Hz  
M
M
M
M
M
M
M
M
Amplifier section Explained  
BUS section Explained  
Rear Gain Control Limiter (RGCL)  
It controls the front pad maximum output power from over  
powering small speakers. The module RGCLwill limit the  
output only when the RCA input selection is set to MAIN  
(not Bus).  
Bus Control Limiter (BCL)  
It controls the front pad maximum output power  
from over powering small speakers. The module  
BCL would limit the output power of any amplifier  
that uses the bus as a signal source.  
Input Signal Control(ISC)  
When switched to LOCAL, individual  
inputs will drive each individual  
amplifier.  
When selecting BUS, the audio  
input from the BUS will drive the  
amplifier.  
L
R
Bus RCA input signal  
Stereo input signal RCAthat delivers the signal to  
the bus. It also allows you do daisy chain the  
signal toadditional Cinénova amplifiers.  
L
R
Keypad Front view  
L
R
Mono/ Stereo input control  
You must switch to MONO when the amplifier  
is wired for MONO  
DC TRIGGER  
12 Volt DC trigger to be connected to source  
output 12 volt trigger. For this to operate, you need  
toswitch the front panel switch to OFF.  
Phoenix type connector  
Should be wired using CAT5 or 5e, CAT6 or 6e.  
This allows zone control via IR. This must be  
connected tothe zone pad.  
4 IR repeater  
Speaker output terminal  
The Cinénova-IR16 has four output IR that  
combine any or all zone IR input. These repeater  
will repeat the sum of IR signal to control any  
source input. Please note that you will need to use  
your source remote, aim it at the pad and it will  
deliver the IRsignal to the source.  
L
-
R
For stereo applications, please follow the  
polarity that is shown on top. For MONO  
follow the bottom polarity.  
Please note that FFI is  
a
Fault Fuse  
Keypad Rear view  
Indicator. Any amplifier that has the FFI  
LED light on will require a fuse replacement  
or possibly service.  
M
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cinénova-IR16 Power Amplifier  
The Cinénova 16 IR allows you to connect several sources to the input stage of the amplfier. It also allows you to aim the remote  
IR Wiring Configuration Sample  
at the zone pad and use the source remote control. As you aim the remote to the pad, the IR signal is transmitted from the pad to  
the amplifier and thereafter amplified. There are four repeaters on the back of the amplifier that can be connected to the source IR  
sensor. Once connected, the user can control the source from the room. the illustration below has a DVD player connected to the  
IR repeater. Please note that the remote in use is that of the DVD player.  
L
R
L
L
L
L
L
L
L
R
R
R
R
L
R
R
R
L
R
R
IR  
SPEAKER OUTPUT  
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
repeater  
FUSE  
110-120VAC-60Hz  
220-240VAC-50Hz  
M
M
M
M
M
M
M
M
Keypad Front view  
Source:DVD player  
IR  
Keypad Rear view  
Remote:DVD player  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Earthquake Sound  
Recommended Configuration  
L
R
L
L
L
L
L
L
R
R
R
R
L
L
R
R
L
R
R
R
SPEAKER OUTPUT  
L
R
L
R
L
R
L
R
L
R
L
R
L
R
L
R
FUSE  
110-120VAC-60Hz  
220-240VAC-50Hz  
M
M
M
M
M
M
M
M
150 Watts RMS/Per Channel  
1-High Power Zones  
MONO/Bridged  
75 Watts RMS/Per Channel  
Background room(s)  
6-Zones STEREO  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cinénova-IR16 Power Amplifier  
SPECIFICATIONS  
Specifications  
Number of channels  
16 Channels  
Dimensions  
Face plate (W x D x H): 19” (482.6mm) x 0.47” (12mm) x 6.87” (174.5mm)  
Mounting (W x H): 18.37” (466.5mm) x 4” (101.5mm)  
Power rating per channel  
(4-Ohm stereo), all channels driven:  
(4-Ohm bridged), 8 channels:  
(8-Ohm stereo), all channels driven:  
(8-Ohm bridged), 8 channels:  
75 Watts RMS  
150 Watts RMS  
50 Watts RMS  
100 Watts RMS  
Chassis (W x D x H): 16.65” (423mm) x 17” (405mm) x 6.71” (170.5mm)  
WC  
DC  
Frequency response:  
20Hz - 20kHz at -0.3dB  
0.01%  
HC  
Total Harmonic Distortion - THD:  
Input sensitivity (for rated output power):  
WM  
HF  
HM  
200mV - 3V  
Cinénova  
16  
IR  
Input impedance  
Independent channels  
Bus Input  
WF  
22 kÙ  
70 kÙ  
Signal to noise ratio:  
AUTO OFF delay time:  
Crosstalk:  
92dB  
12 minutes  
>86dB  
Slew rate:  
50V/ì sec  
29  
FOR YOUR RECORDS  
Gain:  
Damping Factor:  
Remote trigger voltage:  
> 200 @ 8Ù  
5.5 - 28 VDC  
Date of purchase:  
Serial number:  
_________________________________  
_________________________________  
_________________________________  
_________________________________  
_________________________________  
_________________________________  
( _______ ) ________ - _____________  
Power requirement:  
15 Amp 120VAC 60Hz / 10 Amp 220VAC 50Hz  
Authorized dealer name:  
Dealer’s address:  
Fuse ratings:  
Main power fuse:  
Block fuse:  
115V,T15A/250V / 230,T10A/250V  
3 AG type, slow blow 5A/250V  
Weight  
Net weight:  
Gross weight:  
61.7 lbs / 28 kg  
66.1 lbs / 30 kg  
Dealer’s phone number:  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Earthquake Sound  
Troubleshooting and Maintenance  
Troubleshooting  
Maintenance  
The following routine maintenance should be performed on a periodic  
basis:  
Humming noise from speakers.  
Often humming noise is emanating from equipments that  
have their ground prong broken.  
?Clean the exterior surfaces of the unit with a soft, dry, lint-free cloth.  
?Do not use alcohol, benzene, acetone-based cleaners, or strong  
commercial cleaners.  
?Do not use a cloth made with steel wool or metal polish.  
?If the unit is exposed to a dusty environment, a low-pressure  
blower may be used to remove dust from its interior & exterior.  
a) With the amplifier OFF, unplug all RCAs connected to the  
amplifier.  
b) Turn on amp and listen to speakers.  
If buzz has changed or reduced in level, then the problem  
is coming to the amp from another source. The rest of the  
hum you hear is normal and related to the fact that the  
RCAs are open ended and not connected to any thing.  
c) If above steps do not isolate your problem: star-ground all  
components except amplifier from their chassis to the  
processor.  
Front LEDs are ON all the time  
It is normal when running the amplifier to full power that the LEDs  
flicker. If you see that the LEDs are on constantly without  
flickering (solid orange) it means that the amplifier is clipping.  
Reduce volume level toprevent damage tothe unit.  
Turn amplifier ON and circuit breaker shuts down  
This can either be a short in amp or poor circuit breaker in the  
house. Plug amplifier into another outlet on a different circuit  
breaker with nothing connected. If the amp turns on then the  
problem is with your home circuit breaker. If the amplifier still does  
not power up, please call Earthquake toconsult with a technician.  
If you are still stuck...  
1. Contact an authorized Earthquake Dealer.  
2. Contact Earthquake Sound Customer Service at 800-576-7944  
Note:  
questions and additional troubleshooting information.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cinénova-IR16 Power Amplifier  
Product Warranty  
Five (5) year limited warranty  
Earthquake warrants the original purchaser that all Factory Sealed New Audio  
Products to be free from defects in material and workmanship under normal  
and proper use for a period of five (5) years from the date of purchase (as shown  
on the original bill of sale with serial number affixed/written on it). The five (5)  
year warranty period is valid only if an authorized Earthquake dealer properly  
installs the product and the warranty registration card is properly filled out and  
sent to Earthquake Sound Corporation. If a non-authorized party installs the  
product, a ninety (90) day warranty period will be applied.  
surround & dust cap, burnt speaker voice coil.  
• Fading and or deterioration of speaker components & finish due to  
improper exposure to elements.  
• Bent amplifier casing, damaged finish on the casing due to abuse, misuse  
or improper use of cleaning material.  
• Burnt tracers on PCB.  
• Product/part damaged due to poor packaging or abusive shipping  
conditions.  
• Subsequent damage to other products.  
(A) Five (5) years limited warranty plan coverage guidelines:  
warranty claim will not be valid if the warranty registration card is not  
properly filled & returned to Earthquake with a copy of the sales invoice.  
Warranty card is located on the last page of this manual.  
• Firstyear: Earthquake pays for labor, parts, and ground freight (only in US  
mainland, not includingAlaska and Hawaii) (shipping tous is not covered).  
• Secondyear: Earthquake pays forlabor and parts only, customer must pay  
freight both ways.  
• Third, fourth& fifthyear: Earthquake pays labor only. Customer must pay  
forparts and freight both ways.  
A
(E) Service Request:  
To receive product service, contact Earthquake service department at (510)  
732-1000 and request an RMA number (Return Material Authorization). Items  
shipped without a valid RMAnumber will be refused. Make sure you provide us  
with your complete/correct shipping address, a valid phone number, and a brief  
description of the problem you are experiencing with the product. In most cases,  
our technicians might be able to resolve the problem over the phone; thus,  
eliminating the need toship the product.  
(B) Warning:  
Products (sent for repair) that are tested by Earthquake technicians and  
deemed to have no problem(s) will not be covered by the five (5) year limited  
warranty. Customer will be charged a minimum of one (1) hour of labor (at the  
ongoing rates) plus shipping charges back tocustomer.  
(F) Shipping Instructions:  
(C) Earthquake will repair or replace - at our option - all defective  
products/parts subject to the following provisions:  
Product(s) must be packaged in its original protective box(es) to minimize  
transport damage. Shipper claims regarding items damaged in transit must be  
presented to carrier. Earthquake Sound Corporation reserves the right to refuse  
improperly packed product. Original bill of sale must accompany product  
returned for service. We encourage you to include with the package a written  
description of the problem. Ship product to: Earthquake Sound Corp. 2727  
McConeAvenue, Hayward, CA94545. Ph (510) 732-1000. You are responsible  
forthe cost of shipping the product toEarthquake Sound Corporation.  
• Defective products/parts have not been altered or repaired by other than an  
Earthquake factory-approved technician.  
• Products/parts are not subjected to negligence, misuse, improper use or  
accident, damaged by improper line voltage, used with incompatible products  
or have its serial number or any part of it altered, defaced or removed, or have  
been used in any way that is contrary toEarthquake's written instructions.  
(D) Warranty Limitations:  
(G) Disputes Resolution:  
Warranty does not cover products that have been modified or abused,  
including but not limited to the following:  
• Damages to speaker cabinet and cabinet finish due to misuse, abuse or  
improper use of cleaning materials/methods.  
All disputes - between clients and Earthquake Sound Corporation - resulting  
from the five (5) years limited warranty policy must be resolved according to the  
laws &regulations of the county ofAlameda -California.  
• Bent speaker frame, broken speaker connectors, holes in speaker cone,  
We recommend that you place or write  
your serial number here for future  
reference, if necessary.  
PRODUCT REGISTRATION  
This Cinénova-IR16 PowerAmplifier can be registered by returning the Product Registration card attached to this  
purchase and helps expedite warranty issues.  
SERIAL NUMBER  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Sound That Will Move You.  
Earthquake Sound reserves the right to amend details of the specifications without notice  
Copyright © Earthquake Sound Corporation  
Earthquake Sound Corporation | 2727 McCone Avenue. Hayward, CA 94545 | Phone: 510-732-1000 Fax: 510-732-1095  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Edelbrock Automobile Parts Intake Manifolds User Manual
Excalibur electronic Games 370G User Manual
Exido Styling Iron 235 020 User Manual
Exmark Lawn Mower 4500 485 User Manual
Fluke Calculator 5500A COIL User Manual
Freshtel Inflatable Bouncy Toy SPA 2000 User Manual
Gateway Computer Hardware Memory Card Reader User Manual
Genie Garage Door Opener 1200 1500 User Manual
Gigabyte Network Card GA 8IP775 Series User Manual
Golden Technologies Mobility Scooter GC240 User Manual