GE Monogram Refrigerator B480DX User Manual

ZISW/B480DX  
GE Monogram® 48" Built-In Side-by-Side Refrigerator with Dispenser and  
Water Filter  
The Installation Space  
Dimensions and Installation Information (in inches)  
47"  
Case Width  
36" Models 12"  
42" Models 18"  
48" Models 20"  
* Shipping height.  
The refrigerator  
25-3/8  
can be adjusted to  
fit into a cutout that  
is 83-1/2" min. to  
84-1/2” max. height.  
Note that the top  
case trim at the  
*Finished Width  
*84" From  
Floor to  
Top Frame  
*83-1/2"  
at  
Rear  
6"  
Electrical  
Area  
84-1/2" max  
83-1/2" min  
Finished  
5"  
front is 1/2" higher  
and will overlap  
75" From Floor  
to Bottom  
of Electrical  
Area  
upper cabinetry or  
soffit. Use leveling  
legs and wheels  
for a maximum 1"  
height adjustment.  
Opening  
24"  
48"  
Frame to Frame  
26-7/8"  
including  
handle  
5"  
5"  
Water Supply  
3-1/2"  
3-1/2"  
Water and electrical locations  
The opening must be prepared with the electrical and water  
supply located as shown.  
Product Clearances  
These refrigerators are equipped with a 2 position door stop.  
The factory set 130° door swing can be adjusted to 90° if  
clearance to adjacent cabinets or walls is restricted.  
130° Door Swing  
90° Door Swing  
The cutout depth must be 24".  
15"  
20"  
The refrigerator will project forward, slightly beyond  
adjacent cabinetry, depending on your installation.  
23-7/8"  
Behind  
Frame  
The cutout depth beneath a soffit:  
When installed beneath a soffit, the soffit cannot exceed the  
24" installation depth shown. The top case trim overlaps the  
bottom of the soffit.  
28-5/8"  
Additional Specifications  
• A 115 volt 60Hz., 15 or 20 amp power supply is required.  
An individual properly grounded branch circuit or circuit  
breaker is recommended. Install a properly grounded 3-  
prong electrical receptacle recessed into the back wall.  
Electrical must be located on rear wall as shown.  
4" Min.  
to Wall  
Allow minimum clearances for freezer door and fresh food  
door for a full 130° door swing and to allow for pan removal.  
Note: GFI (ground fault interrupter) is not recommended.  
4" minimum clearance is required when door swing is  
adjusted to 90°. If the 90° door stop position is used, pan  
access is maintained, but pan removal is restricted.  
• Water line can enter the opening through the floor or back  
wall. The water line should be 1/4" O.D. copper tubing or  
GE SmartConnectkit between the cold water line and  
water connection location, long enough to extend to the  
front of the refrigerator. Installation of an easily accessible  
shut off valve in the water line is recommended.  
Installation Information: Before installing, consult  
installation instructions packed with product, or online  
at Monogram.com, for current dimensional data.  
For answers to your Monogram,® GE Profile™  
or GE® appliance questions, visit our website  
at ge.com or call GE Answer Center® service,  
800.626.2000.  
As an EnErgy StAr®  
partner, gE has determined  
Listed by  
Underwriters  
that this product meets the  
Laboratories  
EnErgy StAr guidelines  
for energy efficiency.  
Specification Created 3/08  
110180  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ZISW/B480DX  
GE Monogram® 48" Built-In Side-by-Side Refrigerator with Dispenser and  
Water Filter  
Dimensions and Installation Information (in inches)  
3/4" Overlay Panel Dimensions  
Raised Overlay Panel Design  
On Dispenser Models  
For a more custom appearance,  
overlay panels may be installed on  
trimmed models. The overlay panel  
must be secured to a 1/4"-thick  
backer panel which slides into the  
trim. A spacer panel 0.10" thick must  
be placed between the overlay and  
backer panels.  
When a raised panel design is to be used, a custom wide  
middle rail is required to accept the dispenser trim.  
Door  
3/4"  
Overlay  
Panel  
• The middle rail must be wide enough to allow for the  
dispenser trim to overlap the opening.  
• The middle rail must be 1.100" total thickness to accept the  
dispenser trim.  
1/4" Backer Panel  
.10" Spacer  
.250" + .10" + .750" =  
1.100" Total Panel Thickness  
3/4" Overlay Panel  
1/4"  
Backer  
Panel  
.10"  
Spacer  
Overlay Panel  
Spacer Panel  
Backer Panel  
Center each panel over the  
other. Assemble the panels with  
glue and screws. Screws must  
be countersunk into the backer  
panel.  
Dispenser  
Trim  
Wide  
Middle  
Rail is  
16-3/4"  
Required  
NOTE: Left-to-right offset is not  
always equal to top-to-bottom  
offset.  
10-5/8"  
Side View  
A
48" Side-by-Side (in inches)  
Grille Panel  
B
C
A
B
C
D
E
1/4" Backer Panel 45-7/8 9-1/2 68-3/8 18-9/16 26-9/16  
.10" Spacer Panel 45 8-5/8 67 17-1/4 25-1/4  
F
Dispenser  
Cutout  
3/4" Spacer Panel 46-1/8 9-3/4 68-5/8 18-13/16 26-13/16  
*Dispenser Cutout Position (in inches)  
Dispenser Cutout  
G
F
G
48" Models  
17-15/16 5-1/4  
15-3/8"  
Freezer  
Panel  
Fresh  
Food  
*Cut the dispenser opening after the backer, spacer and  
overlay panels have been assembled.  
D
E
9-5/8"  
For answers to your Monogram,® GE Profile™  
or GE® appliance questions, visit our website  
at ge.com or call GE Answer Center® service,  
800.626.2000.  
Important Note: Maximum total panel weight:  
• Fresh food door panel – 75 lbs.  
• Freezer door panel – 53 lbs.  
• Grille panel – 18 lbs.  
As an EnErgy StAr®  
partner, gE has determined  
that this product meets the  
EnErgy StAr guidelines  
for energy efficiency.  
Listed by  
Underwriters  
Laboratories  
Specification Created 3/08  
110180  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ZISW/B480DX  
GE Monogram® 48" Built-In Side-by-Side Refrigerator with Dispenser and  
Water Filter  
Dimensions and Installation Information (in inches)  
1/4" Framed Panel  
Dimensions  
If you choose to install framed  
panels, they must be cut to the  
dimensions shown. The panels will  
slide into the frame on the door and  
grille.  
If the custom panel is less than 1/4"  
thick, and it fits loosely in the door  
frame, it can be backed up with a  
piece of filler material or foam tape  
to improve the fit.  
Dispenser Models  
These refrigerators are supplied with two dispenser trims,  
one for framed panels and one for overlay panels.  
5/16"  
Trim  
Door  
Reveal  
1/4" Framed Panel  
The framed panel must be 1/4" nominal thickness to fit the  
dispenser trim.  
• The dispenser trim fits over the custom panel and snaps  
into the freezer door.  
• If the panel is less than 0.250" thick, a noticeable gap may  
be created around the dispenser trim. Foam tape may be  
applied on the door to improve the fit.  
1/4"  
Panel  
Important Note:  
• If the panel is more than 0.250" thick, the dispenser trim  
cannot be secured to the door.  
Maximum total panel weight:  
• Fresh food door panel – 75 lbs.  
• Freezer door panel – 53 lbs.  
• Grille panel – 18 lbs.  
FREEZER DOOR  
1/4"  
0.250"  
Thick  
Framed  
Panel  
45-7/8"  
Ice / Water Dispenser  
Grille Panel  
9-1/2"  
1/4" Dispenser Trim  
3/4" Overlay Panels  
Dispenser Cutout  
The overlay dispenser trim is designed to fit a total panel  
thickness of 1.100".  
17-13/16"  
Dispenser  
Cutout  
• If the panel is less than 1.100" thick, a noticeable gap may  
be created around the dispenser trim.  
• If the panel is more than 1.100" thick, the dispenser trim  
cannot be secured to the door.  
• The overlay panel must be constructed according to the  
specifications shown to achieve the correct total thickness.  
15-3/8"  
68-3/8"  
5-1/8"  
• Alternative panel construction methods such as securing a  
3/4" panel to a 1/4" backer panel cannot be used. Another  
method, routing a 3/4"-thick panel on all sides, cannot be  
used. These methods will not result in the required 1.100"  
panel thickness.  
9-5/8"  
Freezer  
Panel  
Fresh Food  
Panel  
• When a raised panel design is to be used, a custom middle  
rail is required.  
18-9/16"  
26-9/16"  
1/4" Backer Panel  
1.100"  
Total  
Thickness  
FREEZER DOOR  
.10" Spacer  
Panel  
Ice / Water Dispenser  
For answers to your Monogram,® GE Profile™  
or GE® appliance questions, visit our website  
at ge.com or call GE Answer Center® service,  
800.626.2000.  
3/4" Overlay  
Panel  
3/4" Overlay Dispenser Trim  
As an EnErgy StAr®  
partner, gE has determined  
that this product meets the  
EnErgy StAr guidelines  
for energy efficiency.  
Listed by  
Underwriters  
Laboratories  
Specification Created 3/08  
110180  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ZISW/B480DX  
GE Monogram® 48" Built-In Side-by-Side Refrigerator with Dispenser and  
Water Filter  
Frameless Cabinets: The case trim overlaps  
Dimensions and Installation Information (in inches)  
cabinets at the top and sides. Therefore,  
frameless cabinets may require filler strips  
Refrigerator  
to prevent interference with cabinet door  
swing. The opening must allow for filler  
strips.  
23-7/8" From  
Rear of  
Refrigerator  
1"  
2"  
1-3/4"  
3"  
2-3/4"  
Case  
Trim  
Use this page to  
3/4"  
determine door swing  
interaction with adjacent  
cabinets or countertops.  
1/2"  
1/4"  
1-1/2"  
1-1/4"  
2-1/2"  
2-1/4"  
Top View  
130° Door Swing  
(Factory setting)  
Scale 1:1  
1/4"  
1/2"  
3/4"  
1"  
IMPORTANT NOTE –  
FOR DISPENSER MODELS  
Dispenser models are  
supplied with two dispenser  
trims, one to fit framed  
panels and one for overlay  
panels. Dispenser trim fit  
to the custom panel  
depends on correct  
panel thickness. Framed  
panels must be 1/4"  
nominal. Overlay panels  
should be constructed as  
shown to accomplish a  
total 1.100" thickness.  
1/4"  
1/2"  
3/4"  
1"  
1-1/4"  
Door  
3/4" Overlay  
Panel  
(Nominal Size)  
For answers to your Monogram,® GE Profile™  
or GE® appliance questions, visit our website  
at ge.com or call GE Answer Center® service,  
800.626.2000.  
As an EnErgy StAr®  
partner, gE has determined  
that this product meets the  
EnErgy StAr guidelines  
for energy efficiency.  
Listed by  
Underwriters  
Laboratories  
Specification Created 3/08  
110180  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ZISW/B480DX  
GE Monogram® 48" Built-In Side-by-Side Refrigerator with Dispenser and  
Water Filter  
Dimensions and Installation Information (in inches)  
Refrigerator  
Case Trim  
23-7/8"  
From Rear of  
Refrigerator  
Advance Planning for Built-In Custom  
Side-by-Side Refrigerators  
Use this page to determine door swing  
interaction with adjacent cabinets  
or countertops.  
Frameless Cabinets: The case trim overlaps  
cabinets at the top and sides. Therefore,  
frameless cabinets may require filler strips  
to prevent interference with cabinet door swing.  
The opening must allow for filler strips.  
1/4"  
1/2"  
3/4"  
1"  
1-1/4"  
1-1/2"  
Top View  
90° Door Swing  
(Optional setting)  
Scale 1:1  
IMPORTANT NOTE –  
1/4"  
FOR DISPENSER MODELS  
Door  
Dispenser models are supplied with two  
1/2"  
dispenser trims, one to fit framed panels and  
one for overlay panels. Dispenser trim fit to  
the custom panel depends on correct panel  
thickness. Framed panels must be 1/4" nominal.  
Overlay panels should be constructed as shown  
to accomplish a total 1.100" thickness.  
3/4"  
1"  
1-1/4"  
3/4" Overlay  
Panel  
(Nominal Size)  
For answers to your Monogram,® GE Profile™  
or GE® appliance questions, visit our website  
at ge.com or call GE Answer Center® service,  
800.626.2000.  
As an EnErgy StAr®  
partner, gE has determined  
that this product meets the  
EnErgy StAr guidelines  
for energy efficiency.  
Listed by  
Underwriters  
Laboratories  
Specification Created 3/08  
110180  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ZISW/B480DX  
GE Monogram® 48" Built-In Side-by-Side Refrigerator with Dispenser and  
Water Filter  
Features and Benefits  
• Halogen Light Columns - Located in the freezer and fresh  
food compartments, extend the full length of the interior  
compartments providing brilliant, all-level illumination  
• LED Lighting - Located at the top of the fresh food  
compartment, and inside the high-humidity and climate-  
control drawers, illuminates contents without  
compromising space  
• Advanced Temperature Management System with Multi-Shelf  
Air Tower - Provides even distribution of air throughout  
the refrigerator  
• Climate-Control Drawer - Allows you to express-chill  
beverages, express-thaw meats and select specific  
temperatures for perishable foods  
• Dispenser with Proximity Sensor - Designed to accommodate  
glassware of all sizes, from pitchers to tumblers; control  
graphics light up as you approach and automatically switch  
off when you walk away  
• Humidity-Controlled Vegetable Drawer - Helps preserve the  
freshness of foods  
• Gallon-Size Door Bin - Holds milk containers, two-liter bottles  
and pitchers  
• Adjustable Spillproof Glass Shelves - Easily accommodate  
party trays and platters  
• Drop-Down Shelf - Provides additional space for a casserole  
dish or pizza box  
• Adjustable Deli Drawer on Full-Extension Slides - Keeps  
meats, cheeses and other everyday foods within easy reach  
• Dairy Bin with Center Divider - Has a unique magnetic seal  
that locks in freshness  
• Model ZISW480DX – White dispenser  
• Model ZISB428DX – Black dispenser (shown)  
For answers to your Monogram,® GE Profile™  
or GE® appliance questions, visit our website  
at ge.com or call GE Answer Center® service,  
800.626.2000.  
As an EnErgy StAr®  
partner, gE has determined  
that this product meets the  
EnErgy StAr guidelines  
for energy efficiency.  
Specification Created 3/08  
110180  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Cisco Systems Network Router 1604 User Manual
Clarion Car Video System VMA1131 User Manual
COBY electronic Tablet MID1126 User Manual
Cornelius Plumbing Product IP150 User Manual
Craftsman Lawn Mower 917385123 User Manual
Cub Cadet Lawn Mower RZT S User Manual
Delta Electronics Power Supply Series 240W User Manual
Fujitsu Flat Panel Television PDS4204E H User Manual
Garland Range 36ER32 User Manual
Garmin Fish Finder Ghc 10 User Manual