“
Monogram.
ZIFS36NM – GE Monogram 36" Built-In Stainless Steel All-Freezer
Enclosure Cutout and Product Dimensions (in inches)
10-3/4" Max.
10" Min.
24-3/4"
ZIFS36NMRH, Freezer
Handle on the left side, the door swings left to right.
35" Case
36" Overall
ZIFS36NMLH, Freezer
Handle on the right side, the door swings right to left.
26-3/4"
84-1/2" Max.
83-1/2" Min.
Caution
73-1/2"
Refrigerators are much heavier at the top than
at the bottom – be extra careful when moving.
4"
*Finished Width
• To achieve a flush fit, the finished cutout width must be
at least 36" wide.
2-1/2
Wall View
Electrical
Area
• In a semi-flush installation, the finished cutout must
be 35-1/2".
6
• The electrical and water locations must be located as
shown for either type of installation.
5
24-3/4" Total
Depth
84-1/2" max
83-1/2" min
Finished
75" From Floor
to Bottom
of Electrical
Area
35"
Case
24-3/4"
Case
Opening
Depth
Width
5
5
Water Supply
3-1/2
3-1/2
84*
*36" for a flush installation.
35-1/2" Min. for a semi-flush installation.
Note: Additional cutout width may be required when side
panels are used. Add side panel thickness to the finished
cutout to calculate rough-in width. See installation
examples on the following page.
36" Frame to Frame
26-3/4"
Including
Tubular
Handles
Listed by
Underwriters
Laboratories
R
*Shipped at 84" installation height. Can be adjusted
to 83-1/2" or 84-1/2" with Grille Panel Kits.
Specification Revised 4/05
110154
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
GE Answer Center® service, 800.626.2000.
Download from Www.Somanuals.com. All Manuals Search And Download.
“
Monogram.
ZIFS36NM – GE Monogram 36" Built-In Stainless Steel All-Freezer
Installation at End of Run
1/2" Thick
Side Panels
Refrigerator
Cabinet
36"
37"
Finished Dim.
Roughed-In Dim.
Refrigerator Door
Cabinet
Note: 1/2" thick side panels shown. Side
panels can be any thickness. Add side
panel thickness to outside trim width
(36" or 72" for two models) to calculate
the rough-in dimension. The leading
(front) edge must be finished to match
surrounding cabinetry.
Refrigerator or Freezer
1/2" Thick
Side Panels
Finished Dim.
Rough-In Dim.
72"
73"
Refrigerator and Freezer
installed side-by-side
Installation between base and wall cabinets
1/4" Thick
Side Panels
Refrigerator
Cabinet
Finished Dim.
Rough-In Dim.
35-1/2"
36"
NOTE: 1/4" thick side panels can be inserted
into the case trim, making the rough-in the
same as the outside trim width: 36”.
d
Refrigerator door
Cabinet
Refrigerator or Freezer
For answers to your Monogram, GE Profile™ or
®
Listed by
Underwriters
Laboratories
GE appliance questions, visit our website at
GEAppliances.com or call
Specification Revised 4/05
110154
R
GE Answer Center® service, 800.626.2000.
Download from Www.Somanuals.com. All Manuals Search And Download.
“
Monogram.
ZIFS36NM – GE Monogram 36" Built-In Stainless Steel All-Freezer
Design Information
Flush or Semi-Flush Enclosure Installation
True Flush Installations
Semi-Flush Installation
True Flush Installation
In a flush installation,
the refrigerator door
will align evenly with
the front face of
Semi-Flush Installation
These refrigerators
can also be installed
semi-flush into an
enclosure using the
minimum cutout width.
The case trim creates
a frame around
adjacent cabinet
doors. The refrigerator
blends into the
surrounding cabinetry.
0"
the opening.
3/4"
Monogram built-in refrigerators and freezers can be
installed flush with typical 24-3/4" deep cabinetry.
Side Panels Requirements:
• Side panels are not required whenever the refrigerator or
freezer is installed into an enclosure or between pantry and
oven cabinets.
When installed semi-flush, the case trim will conceal
slight gaps around the enclosure. The refrigerator
will project forward approximately 3/4" beyond the
front face of surrounding cabinetry.
• Side panels are required whenever the sides of the product
are exposed.
• Side panel sizes vary depending on the type of installation being
made.
To accomplish an attractive installation, you must:
1. Determine the need for side panels.
2. Determine side panel thickness.
3. Order matching side panels from the cabinet manufacturer.
Be sure to provide the exact dimensions.
For answers to your Monogram, GE Profile™ or
®
Listed by
Underwriters
Laboratories
GE appliance questions, visit our website at
Specification Revised 4/05
110154
GEAppliances.com or call
R
GE Answer Center® service, 800.626.2000.
Download from Www.Somanuals.com. All Manuals Search And Download.
“
Monogram.
ZIFS36NM – GE Monogram 36" Built-In Stainless Steel All-Freezer
Electrical Outlet
Electrical and Water Connection Locations
Location 2-1/2"
The water line can be routed through the floor or
back wall.
6"
• The icemaker water line should be:
–Approximately 3-1/2" from the floor on the back
5"
wall, or 3-1/2" from the back wall on the floor.
–At least 5" from either side of the opening.
75"
A 115 volt, 60 Hz. 15 or 20 amp power supply is
recommended. An individual properly grounded
5"
branch circuit or circuit breaker is recommended,
as noted on the rating plate.
3-1/2"
• Locate the electrical outlet within 5" x 7" shaded
Water Location
area shown.
–2-1/2" from the left side.
Important: To insure a flush fit and access to the
power cord, locate the electrical outlet as shown.
Between 74" and 81" from the floor.
25"
Clearances
• Factory set for a 130° door swing. Order WX14X99
Minimum
to Wall
90° Door Swing
130° Door Swing
adjustable door stop to reduce swing to as little
as 90°.
When Installed into a corner:
Allow 25" for a full 130° door swing. Allow 15" for
pan removal. Allow 4" min. clearance when door
swing is adjusted to a 90° opening for pan access,
but pan removal is restricted.
36-3/4"
90° door swing with
optional WX14X99
door stop.
4" Min.
to Wall
0"
When installing an All-Refrigerator and All-Freezer
side-by-side, allow 25" for a full 130° door swing,
or 15" min. on the hinge sides for pan access.
25"
Min. to
Wall
25"
Min. to
Wall
130° Door Swing
130° Door Swing
ZUGSS Unified Grille Panel Kit is available for
Accessory Grille Panel Kits
side-by-side installations. See Trim Kit descriptions.
These models are factory set for 84" installation
height. Adjustments to 83-1/2" or 84-1/2" heights
can be made by changing the grille panel.
Order ZGCSS36RH (right hand) or ZGCSS36LH (left
hand) Grille Panel Kit. These kits include 2 grille
panels, for 83-1/2" and 84-1/2" installation heights.
ZUGSS Unified Grille Panel Kit
For side by side installation, order ZUGSS Grille Panel Kit. This
kit provides one continuous panel to span the width of two
products installed together for a unified appearance.
For answers to your Monogram, GE Profile™ or
®
Listed by
Underwriters
Laboratories
GE appliance questions, visit our website at
Specification Revised 4/05
110154
GEAppliances.com or call
R
GE Answer Center® service, 800.626.2000.
Download from Www.Somanuals.com. All Manuals Search And Download.
“
Monogram.
ZIFS36NM – GE Monogram 36" Built-In Stainless Steel All-Freezer
Features and Benefits
• 21.9 Cu. Ft. Freezer Capacity
• Wire Freezer Shelves (5 Adjustable,
1 Fixed, 1 Full-Width Fixed)
• Wire Baskets with Full-Extension Slides
(2 Regular, 4 Large)
• 2 Extra Large Wire Baskets with Easy Access
Lid and Full Extension
• 8 Door Bins and Gallon Storage
• Automatic Defrost Sealed System Design
• Full Extension Slides
• Model ZIFS36NMRH – Stainless steel wrap
(right-handed door swing)
• Model ZIFS36NMLH – Stainless steel wrap
(left-handed door swing)
Specification Revised 4/05
110154
Download from Www.Somanuals.com. All Manuals Search And Download.
|