GE Door 19210 User Manual

GE Model 19210/19211  
Wireless Pushbutton  
Required Tools: Small flat blade screwdriver, drill, drill bit, and phillips screwdriver.  
Included Hardware:  
(2) 3x20mm screws  
(2) Double sided adhesive pads  
Required Tools: Small flat blade screwdriver, drill, drill bit, and phillips screwdriver.  
Chime Tune Setting  
All wireless chimes may have more than one push button. The chime tune for each push  
button is set with jumpers 7-9.  
Single Push Button Kit: If you purchased a kit with a single push button, the chime  
tune will be set to Ding Dong from the factory.  
Dual Push Button Kit: If you purchased a kit with two push buttons, one push button  
will be set to Ding Dong and the other push button will be set to Westminster from the  
factory.  
The following instructions explain how to change the tune on any wireless push button.  
1. Remove the battery from the push button transmitter.  
2. Locate the 9 position jumper shown below.  
9 position jumper (This pushbutton is set for Ding Dong Chime since 7=off, 8=on, and  
9=off.)  
3. Select the desired chime sound from the table below.  
Chime Sound Table  
Position  
Westminster  
Ding Dong  
Knock  
Bronze Chime ON  
Cuckoo Clock ON  
7
ON  
OFF  
OFF  
8
OFF  
ON  
OFF  
ON  
OFF  
ON  
ON  
9
OFF  
OFF  
ON  
OFF  
ON  
ON  
ON  
Foghorn  
Gong  
OFF  
ON  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Remove batteries from the pushbutton by opening the case as shown below.  
2. Locate the pushbutton jumpers shown below.  
Push Button Jumpers  
3. Jumpers 1-6 are used to select 1 of 64 possible home security codes.  
4. To change the house code, add or remove jumpers as needed. After matching  
the existing security code, test the system for proper operation. Positions 1-6 on  
the chime and pushbutton must match exactly.  
Push Button Mounting Instructions  
Note: Avoid mounting the push button on metal surfaces, as it may result in a  
reduced range of transmission. Do not mount in an area of rain (direct weather.)  
a. Removing the back cover  
Download from Www.Somanuals.com. All Manuals Search And Download.  
b. Replacing the back cover  
1. Push buttons are typically mounted at the same height as the door knob or  
handle (between 36" and 44" above the floor).  
2. Before mounting, choose a mounting location that is not farther than 150 feet  
from the chime unit location.  
Not farther than 150 feet  
3. Place the push button where you would like to mount it and with the chime as  
close to its final position as possible and test operation. If it works, mount the  
button. If it does not work, see TROUBLESHOOTING.  
4. Use back cover of push button as a template to mark two screw holes.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Drill two holes with 3/32” size drill in marked locations.  
6. Secure back cover to the mounting surface with two supplied mounting screws.  
7. Press front housing onto back cover.  
8. Test operation. If the chime does not work, see TROUBLESHOOTING.  
Operation  
1. Turn on the chime.  
2. Gently press transmitter button to sound chime.  
Troubleshooting  
Chime doesn't work:  
1. Make sure push button switch is depressed and held for at least 1 second.  
2. Make sure plastic tag is removed from battery.  
3. Make sure house code switches 1-6 on chime and push button match exactly.  
4. Verify battery orientation in push button.  
5. Try fresh batteries.  
6. Make sure chime is not farther than 150 feet away from push button.  
7. Ensure push button is not mounted on metal, near metal studs, or near the floor.  
8. Try a new location for the chime.  
Functional range may be adversely affected by one or more of the following factors:  
weather, radio frequency interference, low transmitter battery and obstructions between  
the transmitter and receiver.  
This device complies with Part 15 of the FCC rules. Operation is subject to the following  
conditions:  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. This device may not cause harmful interference, and  
2. This device must accept interference received, including any interference that  
may cause undesired operation.  
For technical support contact Jasco Products Company at 1-800-654-8483  
Made in China  
is a trademark of  
General Electric Company  
and is used under license to  
Jasco Products Company LLC,  
311 N.W. 122nd Street,  
Oklahoma City, OK 73114.  
Rev. 1-07  
19216  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Crock Pot Slow Cooker Classic 4 7 Quart User Manual
Cuisinart Food Processor DFP 3 User Manual
Curtis Portable CD Player RCD 897 User Manual
Dacor Dishwasher 65537 User Manual
Dell Server r210 II User Manual
Dukane Projector 8043 User Manual
Festool Sander ETS 125 Q User Manual
Fisher Price Model Vehicle h7172 User Manual
Frigidaire Cooktop FFEC2605L S W User Manual
Global Machinery Company Glue Gun DEC005GG User Manual