Safety Information
Owner’s Manual &
Adapter Plugs . . . . . . . . . . . . . . . . . .3
Connect Electricity . . . . . . . . . . . . .2
Extension Cords . . . . . . . . . . . . . . .3
Safety Precautions . . . . . . . . . . . . . .2
Installation Instructions
ASD06
ASM06
ASN06
ASV06
ASM08
ASP08
AST08
ASV08
ASM10
ASP10
ASV10
Operating Instructions
Controls—Control Knobs . . . . .6, 7
Controls—Touch Pads . . . . . . . .4, 5
Care and Cleaning
Air Filter . . . . . . . . . . . . . . . . . . . . . . .8
Grille and Case . . . . . . . . . . . . . . . . .8
Outdoor Coils . . . . . . . . . . . . . . . . . .8
Installation Instructions
Through the Wall
Installation–Optional . . . . . . . . . .15
Window Installation . . . . . . . . .9–14
Troubleshooting Tips . . . . . . . .16
Normal Operating
Sounds . . . . . . . . . . . . . . . . . . . . . . .16
Consumer Support
Consumer Support . . .Back Cover
Product Registration . . . . . . .17, 18
Warranty . . . . . . . . . . . . . . . . . . . . .19
Write the model and serial
numbers here:
# ______________________________
# ______________________________
Find these numbers on a label on the
side of the air conditioner.
49-7400 10-00 JR
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
WARNING!
USE OF EXTENSION CORDS–115-Volt models only
Because of potential safety hazards under certain
CAUTION:
DO NOT use an extension cord with any of the
230/208 volt models.
conditions, we strongly recommend against the
use of an extension cord.
However, if you must use an extension cord,
it is absolutely necessary that it be a UL-listed,
14 gauge, 3-wire grounding type appliance
extension cord having a grounding type plug
and outlet and that the electrical rating of the
cord be 15 amperes (minimum) and 125 volts.
OpeagIructions
USE OF ADAPTER PLUGS –115-Volt models only
Because of potential safety hazards under certain
When disconnecting the power cord from the
conditions, we strongly recommend against the use adapter, always hold the adapter in place with
laIructions
of an adapter plug.
one hand while pulling the power cord plug
with the other hand. If this is not done, the
adapter ground terminal is very likely to break
with repeated use.
However, if you must use an adapter, where
local codes permit, a temporary connection may
be made to a properly grounded 2-prong wall
outlet by use of a UL-listed adapter available at
most local hardware stores.
If the adapter ground terminal breaks,
DO NOT USE the air conditioner until a
proper ground has been established.
The larger slot in the adapter must be aligned
with the larger slot in the wall outlet to provide
proper polarity in the connection of the power
cord.
Attaching the adapter ground terminal to a wall outlet
cover screw does not ground the appliance unless the
cover screw is metal, and not insulated, and the wall
outlet is grounded through the house wiring. You should
have the circuit checked by a qualified electrician to
make sure the outlet is properly grounded.
T
rubleshotingT
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
ips
CnsmeSuport
3
Download from Www.Somanuals.com. All Manuals Search And Download.
About the controls on the air conditioner–models with touch pads.
Features and appearance will vary.
Low
Fan
On
Med
Fan
On
High
Fan
On
CIRCULAIRE
On
ENERGY
SAVER On
SafeyIructions
Cool
Mode On
Fan
Only
On
Timer
On
Air Conditioner Controls
Remote Control
OpeagIructions
ON/OFF
TIMER
Turns air conditioner on and off.
ON–When the air conditioner is off, it can be
set to automatically come on in 1 to 24
hours at its previous setting. Each touch
will set the time in hours.
Display
MODE
OFF–When the air conditioner is on, it can be
set to automatically turn off in 1 to 24
hours. Each touch will set the time in
hours.
Use to set the air conditioner to COOL or FAN.
Increase ▲ /Decrease ▼Pads
Use to set temperature when in COOL mode.
FAN
To cancel the timer, press the TIMER pad
until the display time disappears.
Use to set the fan speed at LOW, MED or HIGH.
CIRCULAIRE
Turn on to provide continuous side-to-side
air circulation.
SLEEP
laIructions
Press to set the air conditioner to run for 8
hours before it automatically shuts off.
For fixed side-to-side air direction, turn ON
until the desired air direction is obtained,
then turn it OFF.
When the SLEEP pad is pressed, SLEEP scrolls
across the display for approximately 15
seconds, then shows the time remaining.
ips
ENERGY SAVER–Controls the fan.
One hour after the sleep timer is set, the set
temperature will automatically increase 1°F.
ON–The fan and compressor cycle on and off.
This results in wider variations of room
temperature and humidity. Normally
used when the room is unoccupied.
Note: The fan will continue to run for a short
time after the compressor cycles off.
To cancel the sleep mode, press the SLEEP
pad a second time.
Note: The sleep timer will be cancelled if the
TIMER, ENERGY SAVER or MODE pad is pressed.
rubleshotingT
T
Remote Control Signal Receiver
OFF–The fan runs all the time, while the
compressor cycles on and off.
This switch must be set at OFF in order to use
the fan settings (on the mode control).
Remote Control
■ To ensure proper operation, aim the
remote control at the signal receiver
on the air conditioner.
■ Make sure nothing is between the air
conditioner and the remote control
that could block the signal.
CnsmeSuport
■ The remote control signal has a range of up
■ Make sure batteries are fresh and installed
correctly–see the Care and Cleaning section.
4
to 21 feet.
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
When the air conditioner is turned on, it will
automatically start in the setting last used.
Lights next to the touch pads on the air conditioner
control panel indicate the selected settings.
COOL Mode
Use the COOL mode with HIGH, MED or LOW fan for
cooling. Use the INCREASE ▲ / DECREASE ▼pads to
set the desired temperature between 64°F and 86°F
in 1°F increments.
Cooling Descriptions
For Normal Cooling–Select the COOL mode and HIGH
or MED fan with a middle set temperature.
OpeagIructions
For Maximum Cooling–Select the COOL mode and
HIGH fan with a lower set temperature.
A thermostat is used to maintain the room
temperature. The compressor will cycle on and off
to keep the room at the set level of comfort. Set the
thermostat at a lower number and the indoor air
will become cooler. Set the thermostat at a higher
number and the indoor air will become warmer.
For Quieter & Nighttime Cooling–Select the COOL
mode and LOW fan with a middle set temperature.
NOTE: If you switch from a COOL setting to OFF or to a
fan setting, wait at least 3 minutes before switching
back to a COOL setting.
NOTE: If the air conditioner is off and is then turned on
while set to COOL, it will take approximately 3 minutes
for the compressor to start and cooling to begin.
laIructions
FAN Mode
Use the FAN at HIGH, MED or LOW to provide air
circulation and filtering without cooling. Since fan
only settings do not provide cooling, a temperature
setting will not be displayed.
Vent Control
The vent control is located on the inside of the air
louvers in the lower right corner.
When set at CLOSE, only the air inside the room will
be circulated and conditioned. When set at OPEN,
some inside air is exhausted outside.
T
rubleshotingT
To open the vent, push the lever to the right.
To close it, push it to the left.
Air Direction – Up and Down
ips
Fingertip pressure on the horizontal louvers adjusts
the air direction up or down.
CnsmeSuport
OR
5
Download from Www.Somanuals.com. All Manuals Search And Download.
About the controls on the air conditioner–models with control knobs.
Features and appearance will vary.
OFF
OFF
HI
FAN
LOW
FAN
OFF
HIGH
FAN
HIGH
COOL
HI
FAN
HI
COOL
SafeyIructions
LOW
FAN
MED
COOL
HI
COOL
LOW
FAN
LOW
COOL
LOW
COOL
LOW
COOL
MED COOL
MODE CONTROLS
Your model will have one of the above type controls.
5
6
4
5
3
4
4
7
3
6
OpeagIructions
8
2
5
3
2
7
2
9
1
6
1
8
1
10
TEMP CONTROLS
Your model will have one of the above type controls.
Controls
laIructions
Mode Controls
Temp Controls
HIGH COOL, MED COOL and LOW COOL provide
cooling with different fan speeds.
The temp control is used to maintain the
room temperature. The compressor will cycle
on and off to keep the room at the same level
of comfort. When you turn the knob to a
higher number the indoor air will become
cooler. Turn the knob to a lower number and
the indoor air will become warmer.
ips
LOW FAN or HIGH FAN provides air circulation
and filtering without cooling.
NOTE: If you move the switch from a cool setting to OFF or to
a fan setting, wait at least 3 minutes before switching back to
a cool setting.
Cooling Descriptions
For Normal Cooling—Select HIGH COOL or MED
COOL with the temp control at midpoint.
rubleshotingT
T
For Maximum Cooling—Select HIGH COOL with the
temp control at the highest number available on
your knob.
For Quieter & Nighttime Cooling—Select LOW COOL
with the temp control at midpoint.
CnsmeSuport
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Additional controls and important information.
Energy Saver (on some models)
The energy saver switch controls the fan.
OFF — The fan runs all the time, while the
compressor cycles on and off.
ON —The fan and compressor cycle on and off
together. This results in wider variations of room
temperature and humidity. Normally used when
the room is unoccupied.
This switch must be set at OFF in order to use the
fan settings (on the mode control).
OpeagIructions
Vent Control (on some models)
The vent control is located on the inside of the air
louvers in the lower right corner.
When set at CLOSE, only the air inside the room will
be circulated and conditioned. When set at OPEN,
some inside air is exhausted outside.
To open the vent, push the lever to the right.
To close it, push it to the left.
laIructions
Air Direction – Side-to-Side
On some models, the side-to-side air direction is
adjusted by the louver levers or by grasping and
moving the inner vertical louvers.
CIRCULAIRE (on some models)
For fixed side-to-side air direction, set the
Circulaire switch to ON until the desired air
direction is obtained, then move it to OFF.
OR
For continuous side-to-side air circulation, set the
Circulaire switch to ON and leave it there.
T
rubleshotingT
Air Direction – Up and Down (on some models)
ips
Fingertip pressure on the horizontal louvers adjusts
the air direction up or down.
CnsmeSuport
OR
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and cleaning of the air conditioner.
How to Insert the Batteries
Remove the battery cover by sliding it
NOTES:
1
according to the arrow direction.
SafeyIructions
■ Use 2 “AAA” (1.5 volt) batteries. Do not use
rechargeable batteries.
Insert new batteries making sure that the (+)
and (–) of battery are installed correctly.
2
■ Remove the batteries from the remote control if
the system is not going to be used for a long time.
Reattach the cover by sliding it back
into position.
3
Grille and Case
Turn the air conditioner off and remove the plug To clean, use water and a mild detergent. Do not
from the wall outlet before cleaning.
use bleach or abrasives.
OpeagIructions
Outdoor Coils
The coils on the outdoor side of the air conditioner
should be checked regularly. If they are clogged
with dirt or soot they may be professionally steam
cleaned, a service available through your GE
service outlet.
Air Filter
laIructions
The air filter behind the front grille should be
checked and cleaned at least every 30 days or more
often if necessary.
To remove (on some models):
Grab the tabs on
the filter and pull
it up and out.
ips
Clean the filter with warm, soapy water. Rinse and
let the filter dry before replacing it.
CAUTION: DO NOT operate the air conditioner without
a filter because dirt and lint will clog it and reduce
performance.
To remove (on some models):
rubleshotingT
Open the inlet grille upward by pulling out the
T
1
To remove (on some models):
bottom of the inlet grille.
Using the tab, pull up slightly on the filter to
release it and pull it down.
Grab the tab on the filter
and pull it to the right.
2
CnsmeSuport
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Preparing to install the air conditioner.
Read these instructions completely and carefully.
Before You Begin
NOTE TO INSTALLER: Leave these instructions with
CAUTION:
the air conditioner after installation is completed.
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.
NOTE TO CONSUMER: Keep this Owner’s Manual
and Installation Instructions for future use.
OpeagIructions
Do not change the plug on the power cord
of this air conditioner.
IMPORTANT NOTES:
For personal safety, this air conditioner must be
properly grounded.
Aluminum house wiring may present
special problems—consult a qualified
electrician.
It is important to have the wall outlet and circuit
checked by a qualified electrician if there is any
doubt as to whether a proper ground exists.
Follow National Electric Codes (NEC) and/or local
codes and ordinances.
laIructions
Electrical Requirements
Some models require 115/120-volt a.c.,
60 Hz grounded outlet protected with
a 15-amp time delay fuse or circuit breaker.
Some models require 230/208-volt a.c.,
protected with a time delay fuse or circuit
breaker. These models should be installed
on their own single branch circuit for best
performance and to prevent overloading
house or apartment wiring circuits, which
could cause a possible fire hazard from
overheating wires.
The 3-prong grounding plug minimizes the
possibility of electric shock hazard. If the wall outlet
you plan to use is only a 2-prong outlet, it is your
responsibility to have it replaced with a properly
grounded 3-prong wall outlet.
T
rubleshotingT
Tools You Will Need
■ Phillips-head screwdriver
■ Adjustable wrench
■ Scissors or knife
■ Pencil
■ Level
■ Ruler or tape measure
ips
CnsmeSuport
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Window Installation Instructions.
Read the section Preparing to Install the Air Conditioner before beginning.
Parts Included
Top mounting rail
Window
sash seal
SafeyIructions
Left
accordion
panel
Foam top
window gasket
Top mounting rail
seal strip
OpeagIructions
Right
accordion
panel
laIructions
Bottom inner
case gasket
ips
Sill support (2)
Type B (8)
Type A
AS_06, AS_08 (18)
AS_10 (21 or 22)
Type C
Bolt (2)
Security bracket (1)
rubleshotingT
T
CnsmeSuport
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Read completely, then follow step-by-step.
Window Requirements
■These instructions are for a standard double-
hung window. You will need to modify them for
other types of windows.
■All supporting parts must be secured to firm
1
wood, masonry or metal.
■The electrical outlet must be within reach of the
power cord.
■The air conditioner can be installed without
the accordion panels if needed to fit in a narrow
window. See the window opening dimensions
below.
OpeagIructions
AS_06
and
AS_10
models
143⁄4″ min.
161⁄8″ min.
AS_08
275⁄8″ to 41″
(With accordion panels)
251⁄2″ to 37″
models
(With accordion panels)
201⁄2″ min.
(Without accordion panels)
235⁄8″ min.
(Without accordion panels)
laIructions
Storm Window Requirements
A storm window frame will not allow the air
conditioner to tilt towards the outside and will keep
it from draining properly. To adjust for this, attach
a piece of wood to the stool.
WOOD PIECES—
2
3
WIDTH: 2″
LENGTH: Long enough to fit inside the window
frame.
Wood
1/2″ higher
than frame
THICKNESS: To determine the thickness, place a
piece of wood on the stool to make it 1/2″ higher
than the top of the storm window frame.
Stool
Attach securely with nails or screws provided by
the installer.
T
Storm window
frame
rubleshotingT
Remove the Front Grille, if attached
To remove the grille:
ips
Lift the grille
up and off the
top tabs.
Remove shipping tape if present.
C
A
On models with a slide out air filter, remove
it (see the Care and Cleaning section) and
the screw behind it (if present) that holds
the grille in place.
CnsmeSuport
On models with a raise up inlet grille, lift it
(see the Care and Cleaning section) and
remove the screw behind it (if present) that
holds the grille in place.
Pull the bottom grille corners out to release
the lower tabs on each side.
B
NOTE: Do not pull the bottom edge toward you more
than 3 inches or you may damage the tabs of the grille.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Window Installation Instructions.
Remove the Air Conditioner From the Case
Remove the 2 screws on each side of the case.
Keep these for later use.
Slide the air conditioner from the case by
gripping the base pan handle and pulling
forward while bracing the case.
A
4
B
SafeyIructions
Front of air conditioner.
OpeagIructions
Front of air conditioner.
Remove packing cardboard and tape if present.
Prepare the Case
Remove the backing from the top mounting
Install the top mounting rail with 4 type A
A
B
5
rail seal strip and attach it to the bottom of the
or 5 type A screws (as the installation requires)
top mounting rail.
from the outside of the case.
Top mounting rail
laIructions
ips
Bottom mounting rail
rubleshotingT
T
Insert the frames for the accordion panels into
the top and bottom mounting rails. Attach the
C
accordion panels to the side of the case using
6 type A or 8 type A screws (as the installation
requires).
CnsmeSuport
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Install the Case in the Window
Cut the window sash seal to the window width
Locate the 3 screw holes along the bottom front
edge of the case. Center the case, side to side,
in the window and mount it to the window sill
using 3 type B screws.
6
7
A
C
and stick the adhesive side to the bottom of
the sash.
OpeagIructions
Top mounting rail
Window sash seal
Type B
screws
Type B
screws
Thread two type C bolts into the support
brackets.
B
Slide the case into the window and lower the
window behind the top mounting rail.
Position the brackets on the case bottom so
they will be near the outermost point on the
window sill. Attach the support brackets to
each side of the case bottom using 4 type A
screws on each side. The case should be
slightly tilted to the outside. Use a level;
about a 1/2 bubble will be the correct case
slant to the outside.
Type B screws
laIructions
Extend the left and right accordion panels to
the vertical window sashes and attach with 4
type B screws.
D
Type A screws
Type C bolts
T
rubleshotingT
Install the Security Bracket and the Foam Top Window Gasket
Attach the security bracket with a type B screw.
Cut the foam top window gasket to the
window width.
A
B
ips
Stuff the foam between the glass and the
window to prevent air and insects from getting
into the room.
C
CnsmeSuport
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Window Installation Instructions.
Install the Air Conditioner in the Case
Slide the air conditioner into the case.
Attach the front grille to the case by inserting the
tabs on the grille into the slots on the front of the
case. Push the grille in until it snaps into place.
A
C
8
Reinstall the 2 screws removed earlier on each
SafeyIructions
side of the case.
Place the bottom inner case gasket between the
bottom of the air conditioner and the inside
bottom of the case. Fold up the ends on both
sides and push them in.
B
OpeagIructions
Guide the lever carefully
through the grille as you
push it in.
Bottom inner
case gasket
Front of air
conditioner.
Secure the front grille to the case by replacing
the screw removed in Step 3. If a screw was not
D
removed in Step 3, secure the grille with a type A
screw. The installation is now complete.
laIructions
ips
rubleshotingT
T
CnsmeSuport
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Through the Wall Installation Instructions–Optional.
The case may be installed through the wall in both existing and new construction.
Read completely, then follow step-by-step.
IMPORTANT
Through the wall installation is not appropriate
1
if any of the side louvers in the case will be
obstructed by the wall.
All side louvers in the case must project on the
outdoor side of the wall.
OpeagIructions
The room side of the case must project into the
room at least 13⁄4″ from the finished wall.
The case must be installed level from side-to-side
and with a slight tilt from front to rear. Use a level;
about a 1/2 bubble will be the correct case slant to
the outside.
Remove the air conditioner from the case.
A
For specific instruction, refer to the Window
Installation Instructions.
Place the case in the wall opening and
secure with 12 1″ long #10 wood screws.
C
Make certain a wall receptacle is available
close to the hole location or make
arrangements to install a receptacle.
laIructions
B
NOTE: Drill pilot holes, if necessary, for proper
installation. If the frame is oversized, use shims
to prevent case distortion.
Finish the Wall Opening
Caulk all four sides on the outdoor side of the case to prevent moisture from getting through to the
interior wall. Use of flashing (drip rail) will further prevent water from dripping inside the wall and
down the outside of the building.
2
T
Plaster line
rubleshotingT
Lintel angle (if required)
Trim molding (if desired)
Caulking
OUTSIDE
ips
INSIDE
Air louvers
(must project on
the outdoor side
of the wall.)
Bottom rail
CnsmeSuport
Wood Filler and Caulking
(above & below the flashing)
Flashing (Drip rail)
4.5 cm (13/4″) min.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
Troubleshooting Tips: Save time and money! Review the chart below first and you may not need to call for service.
Problem
Possible Causes
What To Do
Air conditioner
does not start
The air conditioner
is unplugged.
• Make sure the air conditioner plug is pushed
completely into the outlet.
The fuse is blown/circuit
breaker is tripped.
• Check the house fuse/circuit breaker box and replace
the fuse or reset the breaker.
SafeyIructions
Power failure.
• If power failure occurs, turn the air conditioner OFF.
When power is restored, wait 3 minutes to restart the
air conditioner to prevent tripping of the compressor
overload.
Air conditioner does
not cool as it should
Airflow is restricted.
• Make sure there are no curtains, blinds or furniture
blocking the front of the air conditioner.
The temp control may
not be set correctly.
• On models with touch pads: In COOL mode, press the
DECREASE ▼pad.
• On models with control knobs, turn the temperature
knob to a higher number.
The air filter is dirty.
• Clean the filter at least every 30 days.
See the Operating Instructions section.
OpeagIructions
The room may have been hot.
Cold air is escaping.
• When the air conditioner is first turned on you need to
allow time for the room to cool down.
• Check for open furnace floor registers and cold
air returns.
• Set the air conditioner’s vent to the closed position.
• See “Air conditioner freezing up” below.
Cooling coils have iced up.
Air conditioner
freezing up
Ice blocks the air flow
and stops the air conditioner
from cooling the room.
• On models with control knobs, set the mode control at
HIGH FAN or HIGH COOL with the temp at 1 or 2.
• On models with touch pads, set the controls at
HIGH FAN or HIGH COOL and set the thermostat to
a higher temperature.
laIructions
The remote control is
not working
The batteries are inserted
incorrectly.
• Check the position of the batteries. They should be
inserted in the opposite (+) and (–) direction.
ips
The batteries may be dead.
• Replace the batteries.
• This is normal.
Water drips outside
Water drips indoors
Excessively hot and
humid weather.
The air conditioner is not
tilted to the outside.
• For proper water disposal, make sure the air conditioner
slants slightly from the case front to the rear.
Water collects in
base pan
Moisture is removed from
indoor air and drains into
rear of a cabinet where a fan
blows it against the outdoor
condenser coil.
• This is normal for a short period in areas with little
humidity; normal for a longer period in very humid areas.
rubleshotingT
T
Normal Operating Sounds
■ You may hear a pinging noise caused by water
being picked up and thrown against the
■ Water will collect in the base pan during
high humidity or on rainy days. The water
condenser on rainy days or when the humidity is
high. This design feature helps remove moisture
and improve efficiency.
may overflow and drip from the outdoor side
of the unit.
■ The fan may run even when the compressor
■ You may hear the thermostat click when the
does not.
CnsmeSuport
compressor cycles on and off.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
™
GE Service Protection Plus
GE, a name recognized worldwide for quality and dependability, offers you
™
Service Protection Plus —comprehensive protection on all your appliances—
No Matter What Brand!
Benefits Include:
• Backed by GE
• All brands covered
• Unlimited service calls
• All parts and labor costs included
• No out-of-pocket expenses
• No hidden deductibles
• One 800 number to call
We’ll Cover Any Appliance.
Anywhere. Anytime.*
You will be completely satisfied with our service protection or you may request your money back
on the remaining value of your contract. No questions asked. It’s that simple.
Protect your refrigerator, dishwasher, washer and dryer, range, TV, VCR and much more—any brand!
Plus there’s no extra charge for emergency service and low monthly financing is available. Even icemaker
coverage and food spoilage protection is offered. You can rest easy, knowing that all your valuable
household products are protected against expensive repairs.
Place your confidence in GE and call us in the U.S. toll-free at 800-626-2224
for more information.
*All brands covered, up to 20 years old, in the continental U.S.
Cut here
✁
Please place in envelope and mail to:
General Electric Company
Warranty Registration Department
P.O. Box 32150
Louisville, KY 40232-2150
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us.
We are proud to have you as a customer!
Follow these three steps to protect your new appliance investment:
Complete and mail
your Consumer
After mailing the
registration below,
store this document
in a safe place. It
contains information
you will need should
you require service.
Our service number is
800 GE CARES
Read your Owner’s
Manual carefully.
It will help you
operate your new
appliance properly.
Product Ownership
Registration today.
Have the peace of
mind of knowing we
can contact you in the
unlikely event of
a
safety modification.
1
2 3
(800-432-2737).
Model Number
Serial Number
Important: If you did not get a registration card with your
product, detach and return the form below to
ensure that your product is registered, or register
Cut here
✁
Consumer Product Ownership Registration
Model Number
Serial Number
Mr. ■ Ms. ■ Mrs. ■ Miss ■
First
Name
Last
Name
Street
Address
Apt. #
City
E-mail Address
Zip
Code
State
Date Placed
In Use
Month
Phone
Number
_
_
Day
Year
Occasionally, we may allow selected companies to send you information.
■ Check here if you do not want this information.
General Electric Company
Louisville, Kentucky
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SafeyIructions
Air Conditioner Warranty.
All warranty service provided by our Factory Service Centers,
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
®
or an authorized Customer Care technician. To schedule service,
call 800-GE-CARES.
For The Period Of: We Will Replace:
One Year
From the date of the
original purchase
Any part of the air conditioner which fails due to a defect in materials or workmanship.
During this full one-year warranty, we will also provide, free of charge, all labor
and in-home service to replace the defective part.
OpeagIructions
Five Years
From the date of the
original purchase
Any part of the sealed refrigerating system (the compressor, condenser, evaporator
and all connecting tubing) which fails due to a defect in materials or workmanship.
During this four-year additional warranty, we will also provide, free of charge, all labor
and in-home service to replace the defective part.
What Is Not Covered:
■Service trips to your home to teach you how to use the
product.
■Replacement of house fuses or resetting of circuit
breakers.
laIructions
■Improper installation. If you have an installation problem, ■Failure due to corrosion on models not corrosion-
or if the air conditioner is of improper cooling capacity
for the intended use, contact your dealer or installer.
You are responsible for providing adequate electrical
connecting facilities.
protected.
■Damage to the product caused by improper power supply
voltage, accident, fire, floods or acts of God.
■Incidental or consequential damage caused by possible
defects with this air conditioner.
■Failure of the product resulting from modifications to the
product or due to unreasonable use including failure to
provide reasonable and necessary maintenance.
■In commercial locations labor necessary to move the
unit to a location where it is accessible for service
by an individual technician.
T
rubleshotingT
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
ips
Warrantor: General Electric Company. Louisville, KY 40225
CnsmeSuport
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Support.
GE Appliances Website
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts, catalogs, or even schedule service on-line. You can also “Ask Our Team of Experts™”
your questions, and so much more...
Schedule Service
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience 24 hours any day of the year! Or call 800-GE-CARES (800-432-2737) during normal
business hours.
Real Life Design Studio
GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen
design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800-TDD-GEAC (800-833-4322).
Extended Warranties
Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800-626-2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes
(VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or by phone at
800-626-2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Contact Us
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material, or detach and
use the form in this Owner’s Manual.
Printed in Korea
Download from Www.Somanuals.com. All Manuals Search And Download.
|