LED
State
Green
Description
The module is properly inserted in the FortiGate unit.
QuickStart Guide
FGT ACT
FortiGate ASM-CX4
Off
The module is not receiving power from the FortiGate unit.
Ejection latch open. The module is ready for removal.
Blue
HS
Flashing
Ejection latch opened during system operation.
LED currently not in use.
BYPASS
FORTIGATE
FG ACT
OOS
IPM
BYPASS
HS
Green
Off
The module is properly inserted in the FortiGate unit.
The module is not receiving power from the FortiGate unit.
Connection at 10 Mb/s.
OOS
IPM
Off
1
2
3
4
Port 1 to 4
(Right LED)
Amber
Green
Green
Connection at 100 Mb/s.
Connection at 1000 Mb/s
ASM-CX4
Ethernet cable connected to the port and the FortiGate unit is on.
Port 1 to 4
(Left LED)
Flashing Green Network activity at this interface.
Green
Off
Bypass network activity at this interface.
BYPASS
Normal status or not receiving power from the FortiGate unit.
© Copyright 2009 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trade-
marks of their respective holders.
Regulatory Compliance
Visit these links for more information and documentation for your Fortinet product.
FCC Class A Part 15 CSA/CUS
20 January 2009
01-30006-0474-20090120
Package Contents
Connector
Type
Speed
Protocol Description
Ports 1 to 4
RJ-45
10/100/1000 Base-T
Ethernet Copper network connections.
BYPASS
FORTIGATE
FG ACT
QuickStart Guide
BYPASS
HS
OOS
IPM
BYPASS
FORTIGATE
FG ACT
BYPASS
HS
OOS
1
2
3
4
IPM
1
2
3
4
ASM-CX4
ASM-CX4
Copyright 2008 Fortinet Incorporated. All rights reserved.
Trademarks
Installing the AMC Module
The module should glide smoothly into the chassis. If you encounter any resistance while
sliding the module in, the module could be aligned incorrectly. Pull the module back out
and try inserting it again.
It is important to carefully seat the FortiGate ASM-CX4 module all the way into the chassis.
Only then will the FortiGate ASM-CX4 module power-on.
To complete this procedure, you need:
7. Press the hot swap latch to lock in the module.
• A FortiGate ASM-CX4 module.
• A FortiGate chassis with an empty AMC single-width (SW) opening.
• To avoid any electrostatic discharge, install in a static free area.
8. Power on the FortiGate unit. The hot swap (HS) LED turns on and then begins flashing.
ASM-CX4 module ports
SWx/1
IP:
____.____.____.____
____.____.____.____
____.____.____.____
____.____.____.____
SWx/3
IP:
____.____.____.____
____.____.____.____
____.____.____.____
____.____.____.____
FortiGate ASM-CX4 modules are not hot swappable. The procedure for inserting the
FortiGate ASM-CX4 module into a FortiGate chassis slot requires the FortiGate unit to be
powered off.
Netmask:
IP:
Netmask:
IP:
SWx/2
SWx/4
Netmask:
Netmask:
To avoid any electrostatic discharge (ESD) when handling FortiGate ASM-CX4 modules,
install in a static free area.
Removing the AMC module
To insert a FortiGate ASM-CX4 module into a FortiGate chassis
Should you need to remove the ASM-CX4, shut down the FortiGate unit using proper shut
down procedures.
1. Ensure the FortiGate unit is powered off before proceeding.
2. Remove the panel block on the FortiGate unit using the hot swap latch.
3. Pull the latch on the ASM-CX4 module to the extended position.
To remove the ASM-CX4 module
1. Ensure the FortiGate unit is powered off before proceeding.
4. Insert the ASM-CX4 module into the empty slot in the chassis. Ensure the Fortinet logo
is right-side up. It should be on the lower-right corner of the module.
2. To avoid any electrostatic discharge (ESD) when handling ASM-CX4 module, install in a
static free area.
5. Carefully guide the module into the chassis.
3. Pull the hot swap latch on the right-hand side of the module to the extended position to
unlock the module from the FortiGate unit.
6. Insert the module by applying moderate force to the front faceplate near the upper edge
to slide the module into the slot.
4. Gently pull the hot swap latch to remove the module.
Connecting the Module
When properly inserted into the FortiGate unit, the interfaces of the ASM-CX4 appear in the
interface list by going to System > Network > Interface.
CLI Commands
To enable or disable bypass mode, press the Bypass FortiGate button, or use the following
CLI commands. For more information on these commands go to htp://kc.fortinet.com.
You can add policies, zones and so on as you would with other FortiGate interfaces.
Enable the bridging feature of the module using the Command Line Interface.
exec amc bypass-mode <enable | disable>
Download from Www.Somanuals.com. All Manuals Search And Download.
|