Cr a dle Swing
Cradle
(Seat moves side to side)
Swing
(Seat moves front to back)
Model Number: B0639
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Tools needed for assembly: Phillips Screwdriver and Adjustable Wrench (both not included).
Requires four“D”(LR20) alkaline batteries for operation (not included).
Maximum Weight Limit: 24 lbs. (10.9 kg.)
IMPORTANT! If your child weighs less than 24 lbs., but is really active and appears to be
able to climb out of the swing, immediately discontinue its use.
Product features and decorations may be different than shown in photos above.
Download from Www.Somanuals.com. All Manuals Search And Download.
Pa r ts
Motorized Frame
Tray
4 Toys
(Toys may be different
than shown.)
Pad
Seat Tube
Arm
2 Upper Legs
Seat with Restraint System
2 Feet
2 Lower Legs
1
#8 x / " Screw - 2
2
M4 x 31.5 mm Bolt - 2
M4 Lock Nut - 2
ALL SHOWN ACTUAL SIZE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed.
Never substitute parts.
Motorized Frame
1
#8 x / " Screw - 2
2
SHOWN ACTUAL SIZE
L
Foot
Lower Leg
Tube
Red Dot
R
Elbow Foot
Button
Hole
3
1
• Locate the R and L on the underside of each elbow foot.The
R indicates the right leg.The L indicates the left leg.
• While pressing the upper button on the right leg, fit it into
the tube in the motorized frame. Make sure the upper button
on the right leg “snaps” into the hole in the tube.
• Position a lower leg so that it stands on a flat surface, as shown.
• Fit a foot onto the end of the lower leg.
1
2
• Insert a #8 x / " screw through the bottom of the foot
• Repeat this procedure to assemble the left leg to the
motorized frame.
and into the lower leg.Tighten the screw with a Phillips
screwdriver. Do not over-tighten.
• When the legs are assembled correctly to the tubes in the
motorized frame, you should not see the red dots.
• Repeat this procedure to assemble the other foot to the
other lower leg.
Red Dot
Button
Button
Upper Leg
Straight
End
Button
Hole
Feet
Feet
Lower Leg
4
R
L
2
• Stand the assembly upright.
• Pull the legs out so that the buttons “snap” into the holes in
the motorized frame.
• Position an upper leg so that the red dot is upward.
• When standing behind the product, all four feet should be
flat upon the floor. And, check for an L marking on the left
foot and an R marking on the right foot.
• While pressing the button on the straight end of an upper
leg, insert the upper leg into a lower leg. Make sure the but-
ton on the upper leg “snaps” into the hole in the lower leg.
• Repeat this procedure to assemble the other upper leg to the
other lower leg.
• If the feet are not flat upon the floor, or the left and right feet
have been reversed, remove both lower legs from the upper
legs. Replace them onto the opposite upper leg.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Seat
Ruffle
Seat
Waist
Belts
Slot
Crotch Belt
Pad
Slots
5
7
• Position the seat upright.
• Place the pad onto the seat with the ruffle toward the top
of the seat.
• Fold the bottom of the pad up. Insert the crotch belt through
the slot in the pad. Make sure the crotch belt is not twisted.
• Fold the top of the pad down. Insert the waist belts through
the slots in the pad. Make sure the waist belts are not twisted.
Hole
Hole
Elastic
Loops
8
Peg
6
Elastic
Loops
• Turn the seat upright.
• Fit the pad edges around the rim of the seat.
• Hook the two fastener straps on each side of the pad under
the rim on each side of the seat.
•Fold the top of the pad down.
• Insert the two elastic loops on the pad
through the holes in the seat bottom
Bottom View
• While holding the elastic loops in place, turn the seat
face down.
• Hook the elastic loop on the left side onto the peg on the
right side.
• Hook the elastic loop on the right side onto the peg on the
left side.
Hint: The elastic loops should cross over each other when
attached correctly to the pegs.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
M4 x 31.5 mm Bolt
Rounded
Side
Tray
M4 Lock Nut
Shown Actual Size
Slot
9
11
• Turn the seat upright.
• Insert the tray tabs into the slots in each side of the seat.
• Insert an M4 x 31.5 mm bolt through the seat tube arm
and seat tube.
• Attach an M4 lock nut to the bolt. Make sure the rounded
side of the lock nut faces out.
• Using an adjustable wrench, hold the lock nut in place.
Then using a Phillips screwdriver, tighten the bolt. Do not
over-tighten.
Seat Tube
Arm Hole
Press
Seat Tube
Button
Motorized
Frame Tube
Hole
10
Press
Seat Tube
Button
• While pressing the button on the seat tube, slide the seat
tube arm onto the seat tube. Make sure the button on the
seat tube “snaps“ into the hole in the seat tube arm.
12
• Press the button on the seat tube and slide the seat tube
into the motorized frame tube. Make sure the button on
the seat tube “snaps”into the larger hole in the motorized
frame tube.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Mobile
Clip
Toy
Clip
Slot
14
Toy
13
M4 x 31.5 mm Bolt
Rounded
Side
• Fit the string (below the knot) of a toy
through the slot in a clip on the mobile.
• Pull down on the toy to be sure it is secure on the mobile.
• Repeat this procedure to assemble the other three toys to
the mobile.
• Insert a M4 x 31.5 mm bolt
through smaller hole in the
motorized frame tube and into
the seat tube.
M4 Lock Nut
Shown Actual Size
Note: Toys may be different than those shown.
• Attach an M4 lock nut to the bolt. Make sure the rounded
side of the lock nut faces out.
• Using an adjustable wrench, hold the lock nut in place.
Then, using a Phillips Screwdriver, tighten the bolt. Do not
over-tighten.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Ba tter y Tips
Ba tter y Insta lla tion
• Do not mix old and new batteries.
• Do not mix different types of batteries: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
• Remove the batteries during long periods of non-use.
Always remove exhausted batteries from this product.
Battery leakage and corrosion can damage this product.
Dispose of batteries safely.
• Do not dispose of batteries in a fire.The batteries may
explode or leak.
1.5V x 4
“D”(LR20)
+
-
• Never short-circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
SHOWN ACTUAL SIZE
• Only batteries of the same or equivalent type as
recommended in the battery installation instructions
are to be used.
Battery
Compartment
Door
• If removable rechargeable batteries are used, they are only
to be charged under adult supervision.
• Rechargeable batteries are to be removed from the product
before they are charged.
• If you use a battery charger, it should be examined regularly
for damage to the cord, plug, enclosure and other parts.
Do not use a damaged battery charger until it has been
properly repaired.
Battery
Compartment
• Using a coin, press the tab on the battery compartment door
and remove it.
• Insert four“D”(LR20) alkaline batteries, as indicated inside
the battery compartment.
Hint: We recommend using alkaline batteries for longer
battery life.
• Replace the battery compartment door.
Hint: If the swinging motion or mobile movement becomes
noticeably slower or stops, remove the batteries and replace
them with four, new“D”(LR20) alkaline batteries. Dispose of
exhausted batteries properly.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Swing a nd Mobile Use
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never
substitute parts.
Restraint Belts
To Unfold
Button
Button
Leg
Waist Belt
Leg
Waist Belt
Crotch Belt
1
2
• Firmly pull the legs outward. Make sure the buttons snap
into the notches in the motorized frame.
• Place your child in the seat.
• Check to be sure the legs are locked into position by
pushing the legs inward.The legs should not move.
• Pull the crotch belt up between your child’s legs and fasten
both waist belts to the crotch belt. Make sure you hear a
“click” on both sides.
WARNING
Anchored End
Anchored End
Buckle
A
To prevent injury or death from falls
or sliding out, always use the
restraint system. Never rely on the
tray to restrain child.
B
B
A
Free End
Free End
3
To Tighten
To Loosen
To tighten the waist belts:
• Feed the anchored end of the waist belt up through the
A
buckle to form a loop
.
B
• Pull the free end of the waist belt
.
• Repeat this procedure to tighten the other waist belt.
To loosen the waist belts:
• Feed the free end of the waist belt up through the buckle
A
to form a loop
.
• Enlarge the loop by pulling on the end of the loop
toward the buckle.
• Pull the anchored end of the waist belt to shorten the
B
free end of the waist belt
.
• Repeat this procedure to loosen the other waist belt.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Swing a nd Mobile Use
Adjust Swing Motion
Using the Tray
PRESS
Seat Tube Button
Seat Tube
Tray
Tab
TURN
Slot
6
• Fit the tabs on the tray into the slots in the sides of the seat.
• To remove the tray, pull the tab out on one side of tray
and lift.
Storage
4
Swing
Cradle
Button
You can adjust the motion of the swing: side to side or
front to back.
Button
• Press the seat tube button to unlock the seat tube.
• Rotate the seat tube to the desired position.
Adjust Seat to Recline or Upright
Lower Leg
Button
Lower Leg
Button
Upright
7
Recline
• Press the buttons on the back of the motorized frame while
pushing the legs inward.
• Lean the swing frame against a wall for storage.
IMPORTANT! Remove the batteries for long-term storage.
Front Edge
of Seat
5
Press Seat Position Buttons
Hint: The legs may be disassembled for long-term storage.
Press the button on each lower leg and remove them from the
upper legs.
You can adjust the seat to two different positions:
Recline or Upright.
• From behind the seat, press both seat position buttons.
• Lift the seat back until the buttons “snap” into the
upright position.
• Push the seat back down until the buttons “snap” into
10
the recline position.
Download from Www.Somanuals.com. All Manuals Search And Download.
Swing a nd Mobile Use
Speed Dial
Reset
Button
Mode Switch
Control Panel
• Slide the mode switch to:
Swing and Mobile
Hints:
• As with most battery-powered swings, a heavier child reduces
the amount of swinging motion on all settings. In most cases,
the low setting works best for a smaller child while the high
setting works best for a larger child.
• If the low setting provides too much swinging motion for
your child, try placing one end of a blanket underneath your
child and let the other end of the blanket drape down
while swinging.
Swing Only
Mobile Only
Swing and Mobile Off
• Turn the speed dial to select any of six speed settings
.
•
The mobile turns off after approximately seven minutes.
To restart the mobile, press the reset button for another
seven minutes of use.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Pr oblems a nd Solutions
Problem
Probable Cause
Solution
Motor is not running;
no swinging
Mode switch is in OFF
position
Slide the mode switch to
swing and mobile or
swing only.
or
mobile only position
Batteries incorrectly installed
Remove the batteries and replace in correct orientation, as
indicated inside the battery compartment.
Dead batteries
Replace all four batteries with four, fresh “D”alkaline batteries.
Motor is running but
swinging stops after a
few minutes
Need to start swinging motion
To start swinging motion, give the seat a light push.
Swing motion setting is
inappropriate for child’s weight
Adjust the speed dial to a higher speed setting and give the
seat a light push.
Weak batteries
Replace all four batteries with four, fresh “D”alkaline batteries.
No difference noticed in
swinging motion after
speed dial is adjusted
Swing did not have sufficient time
to adjust to different setting
Allow the swing time to adjust to new setting.
Weak batteries
Replace all four batteries with four, fresh “D”alkaline batteries.
Mobile does not work
Mode switch is in OFF
swing only position
position or
Slide mode switch to desired setting
.
Mobile turns off automatically
after seven minutes
Press the reset button
seven minutes.
to restart mobile for another
Ca re
• Remove the tray from the seat.
• Unbuckle the restraint system.
• Remove the pad elastic loops from the pegs and unfasten the pad fasteners from the seat.
• Remove the pad from the restraint system.
• Remove the toys from the mobile.
• Machine wash the pad and toys in cold water with a mild detergent. Do not use bleach.Tumble dry on low heat and
remove promptly.
• To clean the seat, restraint system, tray, mobile and motorized frame, use a mild cleaning agent and damp cloth. Rinse with clean
water to remove residue.
• Replace the pad onto the seat.
• Replace the toys on the mobile.
• Periodically check the swing for loose fasteners or broken parts and tighten as needed.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2002 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Printed in China
B0639a-0920
Download from Www.Somanuals.com. All Manuals Search And Download.
|