H8910
Instructions
Please keep this instruction sheet
for future reference, as it contains
important information.
Adult assembly is required.
No tools needed for assembly.
Download from Www.Somanuals.com. All Mwanuwals wSea.rfchisAhndeDorw-nploardi.ce.com
Bubblin’ Fun
P
R
E
S
S
1
3
• Remove and discard the cap and seal
from the bubble solution bottle.
• Press down on the bottle for about
15 seconds to fill the mower.
• Carefully fit the bottle to the bottom of
the filler cap attached to the front of
the mower. Twist the bottle to attach.
2
• Insert the bottle, cap side down,
into the opening near the front of
the mower.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2005 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO H8910pr-0920
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Bubblin’ Fun
• If your mower still does not make
bubbles:
- Check to be sure there is enough
bubble solution in the mower.
- Make sure all four wheels contact
the ground when pushing the
mower.
- Empty bubble solution from the
mower. Wash the bubble chamber
and filler opening. Refill with fresh
bubble solution (see page 5).
Note: We do not recommend the
use of silicones or oily lubricants
on this toy. As with any bubble
producing toy, when even a very
small amount of silicone or oily
lubricants are put into or used near
the bubble chambers, bubbles will
not form.
• Push the bubble mower so that all
four wheels contact the ground.
• Bubbles begin flowing after the
mower has been pushed about
15-20 walking steps. As long as the
mower is being pushed, bubbles
continue to flow.
• When bubbles stop, press down
on the bubble bottle again for 15
seconds to refill.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Let’s Clean Up
1
3
• Lift to remove the bubble solution
bottle from the mower. Twist to
remove the filler cap. Set the bottle
• Tip the mower forward to empty all
the water.
Cap End Up
For Storage
4
2
• Replace the filler cap on the bubble
solution bottle and place the bottle
in the filler opening cap end up.
Hint: Please keep the bubble
solution bottle with your toy and
refill as necessary.
• Thoroughly rinse the bubble chamber
on the side of the mower and filler
opening near the front of the mower
with clean water from a garden hose
or faucet.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems and Solutions
Problem
No bubbles
Cause
Not enough bubble solution in
bubble chamber
Solution
Press down on bubble solution
bottle for 15 seconds to refill.
Bubble chamber is clogged
and dirty
Follow instructions in “Let’s
Clean Up” section to clean bubble
chamber thoroughly.
You have not walked far enough
to produce bubbles
The bubble mower needs to be
pushed a minimum of 15-20
walking steps before bubbles
begin to flow.
You are walking too quickly
Walk at a slow, steady pace.
The rear wheels do not contact
the ground
Push the mower so that the
rear wheels always contact
the ground.
Silicone or oily lubricants
may have gotten in the
bubble chamber
Never use silicone or oily
lubricants on this product (the
wheels). Bubbles will not form
if even a very small amount of
these substances get into the
bubble chamber.
Bubble solution is leaking from
the mower
Bubble chamber over-filled
Fill only by using filler cap. The
filler cap dispenses the correct
amount of solution.
The mower is used on an
inclined surface
Use the mower only on flat,
level ground.
Bubble solution is foaming
Bubble chamber is clogged
Follow instructions in "Let's
Clean Up" section to clean bubble
chamber thoroughly.
Consumer Information
®
Call Fisher-Price Consumer Relations, toll-free at 1-800-432-5437, 8 AM- 6 PM EST
Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
®
Write to us at: Fisher-Price Consumer Relations, 636 Girard Avenue,
East Aurora, New York 14052.
For countries outside the United States:
CANADA - Questions? 1-800-432-5437, Mattel Canada Inc., 6155 Freemont Blvd., Mississauga,
GREAT BRITAIN - Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500303;
AUSTRALIA - Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond,
Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.
NEW ZEALAND - 16-18 William Pickering Drive, Albany 1331, Auckland.
ASIA - Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City,
Tsimshatsui, HK, China.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|