Parts
IMPORTANT! Please remove all parts from the package and identify them before assembly.
Tray
Rear Base
Front Base
Hint: Do not remove the plastic inserts
inside the tubes of the front base.
Seat with Restraint
Seat Support
Footrest
Seat Back with Restraint
Seat Back Pad
2 Brackets (Left and Right)
Seat Pad
2 Frames
Hint: Do not remove the plastic
insert inside the tube in each frame.
FASTENERS SHOWN ACTUAL SIZE
#8 x ¾" Screw with Plastic Retainer – 4
#8 x ¾" Blunt Screw – 4
#8 x ¾" Pointed Screw – 2
Note: Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
CAUTION
This package contains small parts
in its unassembled state.
Adult assembly is required.
IMPORTANT! Before assembly and each use, inspect this
product for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use if any parts are missing or broken.
Contact Fisher-Price® for replacement parts and instructions if
needed. Never substitute parts.
2
• Fit a #8 x ¾" screw with retainer into the rear base and tighten.
• Repeat steps 1 and 2 to assemble the other frame to the
rear base.
Tapered Frame Tube
Seat Support
Frame Tubes
Rear Base
Frame Latches
1
With the Fisher-Price® logo facing out, fit the tapered frame tube
into the rear base.
Frame Assembly
3
• Lay the frame assembly down with long frame tubes up.
• Position the seat support with the frame latches down.
• Slide the seat support onto the frame tubes.
Hint: Push the seat support all the way to the top of the
assembly. You will hear several "clicks".
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Seat Support
Footrest
Front Base
4
• Fit the front base into the frame tubes.
6
• Lift the frame assembly upright.
• Fit the footrest onto the seat support, as shown.
5
• Insert two #8 x ¾" screws with retainers into the holes in
each frame tube and tighten.
Hint: If you cannot insert the screws into the frame tubes, you
have assembled the front base backwards. Remove it, turn it
around and re-assemble it to the frame tubes.
Footrest
7
• Insert two #8 x ¾" blunt end screws into the holes on each
side of the footrest and tighten.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Seat Support Tube
Seat Support Tube
Seat Support
Seat Support
B
B
A
A
Right Bracket
10
Left Bracket
8
• First fit the right bracket (labeled 2) onto the seat support
A
tube closest to you
.
• Turn the frame over with the footrest facing away from you.
• Then, slide the right bracket completely onto the seat
• First fit the left bracket (labeled 1) onto the seat support tube
B
support
.
A
closest to you
.
• Then, slide the left bracket completely onto the seat
B
support
.
Hint: The brackets are designed to fit each side of the seat
support one way. If the bracket does not seem to fit, try the
other one.
11
• Push to align the slot in the right bracket with the hole in the
seat support.
3
• Insert a #8 x /4" pointed end screw through the right bracket
and into the seat support and tighten.
• Turn the frame upright.
9
• Push to align the slot in the left bracket with the hole in the
seat support.
3
• Insert a #8 x /4" pointed end screw through the left bracket
and into the seat support and tighten.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Pegs
Tab
Tab
Slot
Slot
Seat Pad
Elastic Loops
12
• At an angle, fit the tabs on the seat back into the slots in
the seat.
• Push the seat back to “snap” in place.
• Pull on the seat back to be sure it is secure to the seat bottom.
14
• Pull the ends of the waist belts and crotch belt through the
slots in the seat pad.
• Fit the elastic loops on the seat pad down through the slots in
the seat.
• Turn the seat upside down.
• Pull the elastic loops through the slots in the seat and fit the
elastic loops to the pegs.
13
• Unbuckle the lower restraint.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Lower Shoulder Belt Slots
Seat Back Pad
Straps
Seat Back
17
Smaller Baby
• Insert the ends of the shoulder belts through the lower slots
in the pad and seat back.
15
• Pull the ends of the shoulder belts through the slots in the
seat pad.
Upper Shoulder Belt Slots
• Fit the straps on the back of the seat back pad into the slots
in the seat back pad.
• Press to fasten the straps to secure the seat back pad.
18
Larger Baby
• Insert the ends of the shoulder belts through the upper slots
in the pad and seat back.
16
• To adjust the restraint height for baby, push to remove the
shoulder belts from the seat back.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Securing Your Child
WARNING
Prevent serious injury or death from
falls or sliding out:
• Only use for a child capable of sitting
upright unassisted.
• NEVER leave child unattended.
High Chair Use:
• ALWAYS secure child with restraint
belts adjusted to fit your child snugly.
The tray is not designed to hold child
in the product.
When attached to adult chair:
• Use restraint belts until child is able to
get in and out of the product without
help (about 21/2 years old).
Slots
19
• Fit the "T" end of each shoulder belt through the slots in the
lower restraint.
Seat Assembly
Frame Assembly
20
• Place the seat assembly on the frame assembly and push to
lock in place. You should hear a "click".
Note: The seat assembly will only fit on the frame assembly if
the chair attachment strap door is closed. If the seat assembly
does not lock onto the frame assembly, check to make sure the
sliding door under the seat is completely closed.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing Your Child
Adjuster
Adjuster
Waist/Shoulder
Belt
Waist/Shoulder
Belt
Crotch Belt
TIGHTEN
3
• To tighten the waist belts: Feed the anchored end of the
1
A
waist belt up through the buckle to form a loop
. Pull the
B
free end of the waist belt
.
• Place your child in the seat. Position the crotch belt between
your child’s legs.
• To tighten the shoulder belts: Hold the adjuster and pull the
C
shoulder belt down
.
• Fasten both waist/shoulder belts to each side of the crotch
belt. Make sure you hear a "click" on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
LOOSEN
4
• To loosen the waist belts: Feed the free end of the waist belt
A
up through the buckle to form a loop
. Enlarge the loop by
pulling on the end of the loop toward the buckle.
• Pull the anchored end of the waist belt to shorten the free end
2
B
of the waist belt
.
C
• To loosen the shoulder belts: Lift the adjuster
.
• Tighten each waist belt/shoulder belt so that the restraint
system is snug against your child. Please refer to the
next section for instructions to tighten the waist belts/
shoulder belts.
Note: After adjusting the restraint system to fit your child,
make sure you pull on it to be sure it is securely fastened.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Tray
WARNING
Prevent serious injury or death from
falls or sliding out:
Release Bar
• ALWAYS secure child with restraint
belts adjusted to fit your child snugly.
The tray is not designed to hold child
in the product.
2
Tray
• While pushing the release bar on the front of the tray, adjust
the tray forward or backward.
Armrest
1
Release Bar
• Fit the tray onto the seat armrests. Push down until the tray
"snaps" into place.
Hint: Before use, thoroughly wash all parts (the tray) that may
contact food. The tray is not dishwasher or microwave safe.
3
• While pushing the release bar on the front of the tray, pull the
tray away from the armrests.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Seat
Attaching To An Adult Chair
WARNING
Prevent serious injury or death from
falls or sliding out:
• Only use for a child capable of sitting
upright unassisted.
PRESS
• NEVER leave child unattended.
• Use restraint belts until child is able to
get in and out of the product without
help (about 21/2 years old).
• NEVER use in motor vehicles.
• ALWAYS secure the product on a
chair using bottom and back attach-
ment straps. NEVER use on a stool
or bench that does not have a
seat back.
Seat Height Adjuster
To adjust the seat height:
• Press the levers on both seat height adjusters and lift or
lower the seat to any of five different heights.
• Make sure both sides of the seat are adjusted to the
same height.
• Push the seat to be sure the seat is locked in place.
To prevent falls:
• NEVER release the seat with child
in product.
• NEVER carry child in the seat.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching To An Adult Chair
B
A
Chair
Attachment
Straps
Door
3
Latch
• Turn the seat over.
• Slide the door open and pull out the chair attachment straps.
1
Openings
A
B
• While sliding the switch
pull the latch towards you
.
Openings
4
• Match the buckle on each strap to the matching buckle icon
near each slot in the seat. Feed each strap through the
matching slot on the seat.
2
• Lift the seat off the base.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching To An Adult Chair
Remove the Seat Back and
Shoulder Belts
5
• Turn the seat over and place the seat on a chair.
1
A
• Wrap the bottom straps around the bottom of the chair
.
B
Buckle the straps
. Make sure you hear a "click". Pull the
• Pull the shoulder belts out of the waist restraint buckle slots.
C
free end of each strap to tighten on the chair
.
LIFT
Seat Back
PULL TAB
6
2
• Pull the tab on the seat back. Lift to remove the seat back
from the seat.
• Store the seat back, seat back pad and shoulder belts in a
safe place for future use.
D
• Wrap the back straps around the back of the chair
.
E
Buckle the straps
. Make sure you hear a "click". Pull the
F
free end of each strap to tighten on the chair
.
• Pull up on the seat to be sure it is secure to the chair.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage
Attaching the Seat To the Frame
Chair
Attachment
Straps
Door
1
• Turn the seat over and open the door. Carefully fit the chair
attachment straps into the compartment.
• Pull the frame release latches forward and push the rear legs
toward the front legs.
2
IMPORTANT! Close the door completely. If you do not close
the door, the seat will not fit on the high chair base.
Care
• The tray, pads, seat, seat attachment straps and restraint
belts may be wiped clean using a mild cleaning solution and
damp cloth. Do not use bleach. Do not use harsh or abrasive
cleansers. Rinse clean with water to remove residue.
To remove the pad:
• Push to remove the shoulder belts, waist belts and crotch
belt from the seat and pads.
• Unfasten the straps and loops on the seat back and
seat bottom.
• Remove the pads from the seat.
• To replace the pad and restraint straps, refer to the assembly
instructions in this manual.
IMPORTANT! Be sure to replace the restraint system. Never
use this product without the restraint system when used as a
high chair or when attached to an adult chair (until your child
can get in and out of the product without help).
3
• Fit the seat onto the high chair frame. Push to "snap" into
place. Pull up on the seat to be sure it is secure to the high
chair frame.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CANADA
Mattel Canada Inc., 6155 Freemont Blvd.,Mississauga, Ontario L5R 3W2.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO
T0250pr-0920
Download from Www.Somanuals.com. All Manuals Search And Download.
|