First Alert Home Security System FA130CP User Manual

)$ꢀꢁꢂ&3

6HꢁXULW\ꢀ6\VWHPV

READ

A260

ARMED

OFF

A560

8 *

VHU·Vꢀ XLGH

K0736-1 8/02

Download from Www.Somanuals.com. All Manuals Search And Download.

7DEOHꢀRIꢀ&RQWHQWV

System Overview....................................................................................................................5

Introduction .......................................................................................................................... 5

System Basics ....................................................................................................................... 5

Using the Voice Message Center ......................................................................................... 7

About The Keypads................................................................................................................8

General Information............................................................................................................. 8

Functions of the Keypads...................................................................................................10

Entry/Exit Delays .................................................................................................................12

Exit Delay............................................................................................................................ 12

Entry Delay......................................................................................................................... 12

Exit Alarms......................................................................................................................... 13

Checking For Open Zones..................................................................................................14

Using the [∗] Key ................................................................................................................ 14

Arming the System...............................................................................................................15

Stay Mode: Arms Perimeter Only, Entry Delay On......................................................... 15

Night-Stay Mode: Arms Perimeter Only, Plus Selected Zones ....................................... 15

Instant Mode: Arms Perimeter Only, Entry Delay Off.................................................... 15

Away Mode: Arms Entire System, Entry Delay On......................................................... 15

Maximum Mode: Arms Entire System, Entry Delay Off................................................. 15

Arming Commands............................................................................................................. 16

Single Button Arming ........................................................................................................ 17

Step Arming Feature.......................................................................................................... 17

Using the Keyswitch............................................................................................................18

Using the Keyswitch........................................................................................................... 18

Disarming and Silencing Alarms......................................................................................19

Using the [OFF] key........................................................................................................... 19

Bypassing Protection Zones ..............................................................................................20

Using the BYPASS Key...................................................................................................... 20

Quick Bypass ...................................................................................................................... 21

Chime Mode ...........................................................................................................................22

Date and Time.......................................................................................................................23

Viewing the Current Date and Time................................................................................. 23

Setting the Date and Time................................................................................................. 23

– 3 –

Download from Www.Somanuals.com. All Manuals Search And Download.

7DEOHꢀRIꢀ&RQWHQWV

Panic Keys..............................................................................................................................24

Using Panic Keys................................................................................................................ 24

Macro Key Programming & Usage...................................................................................25

About Macro Keys............................................................................................................... 25

Example of Macro Programming....................................................................................... 26

Using a Programmed Macro Key....................................................................................... 26

Using Device Commands....................................................................................................27

About Device Commands ................................................................................................... 27

Paging Feature .....................................................................................................................28

About Automatic Paging .................................................................................................... 28

Manual Paging.................................................................................................................... 29

Latch Key Paging ...............................................................................................................29

Security Codes & Authority Levels..................................................................................30

About Security Codes ......................................................................................................... 30

Authority Level Definitions ............................................................................................... 30

How to Assign User Codes and Attributes........................................................................ 31

Scheduling .............................................................................................................................32

About Scheduling................................................................................................................ 32

Creating Schedules............................................................................................................. 32

Event Logging Procedures.................................................................................................34

About Event Logging.......................................................................................................... 34

Viewing the Event Log....................................................................................................... 34

Table of Event Log Codes................................................................................................... 35

Testing the System (To Be Conducted Weekly)............................................................36

About Testing the System ..................................................................................................36

Trouble Conditions..............................................................................................................37

Maintaining Your System...................................................................................................40

Fire Alarm System (If Installed).......................................................................................41

Quick Guide to Basic System Functions ........................................................................45

Summary of Audible/Visual Notifications......................................................................46

Regulatory Statements and Warnings ............................................................................48

Charts of Your System’sFeatures....................................................................................49

– 4 –

Download from Www.Somanuals.com. All Manuals Search And Download.

6\VWHPꢀ2YHUYLHZ

,QWURGXꢀWLRQ

Congratulations on your ownership of the First Alert Professional Security System.

You've made a wise decision in choosing it, for it represents the latest in security

protection technology today. This system provides:

• Three forms of protection: burglary, fire* and emergency

• At least one keypad which provides control of system and displays system status

• Various sensors for perimeter and interior burglary protection

• Smoke or combustion detectors* designed to provide early warning in case of fire.

Your system may also have been programmed to automatically send alarm or status

messages over the phone lines to a Central Monitoring Station.

* Commercial installations and some residential systems may not include fire

protection – check with your installer.

6\VWHPꢁ%DVLꢀV

Burglary Protection

• Several modes of burglary protection: Stay, Night-Stay, Away, Instant, Maximum.

STAY: arms perimeter zones only and entry delay is on

INSTANT: same as STAY, except entry delay is off

NIGHT-STAY: arms perimeter zones and selected interior zones; entry delay on

AWAY: arms perimeter and all interior zones, entry delay is on

MAXIMUM: same as AWAY, except entry delay is off

• You can BYPASS selected zones while leaving the rest of the system armed.

• CHIME mode alerts you to the opening of protected doors and windows while the

system is disarmed.

Fire Protection

• Fire protection is always active (if installed) and an alarm sounds if a fire

condition is detected

• If necessary, you can manually initiate a fire alarm using the keypad (if

programmed).

• Refer to the Fire Alarm System section for information regarding fire protection,

smoke detectors and planning emergency exit routes.

Security Codes

• You were assigned a 4-digit security code during system installation.

• Use your security code when arming and disarming the system, and when

performing other system functions.

• Other users can be assigned different security codes, each with different

authority levels, which define the system functions a particular user can perform.

– 5 –

Download from Www.Somanuals.com. All Manuals Search And Download.

6\VWHPꢀ2YHUYLHZꢀꢁ&RQWLQXHGꢂ

Zones

• The system sensing devices have been assigned to various “zones,” which are

specific areas of protection (e.g., front door, kitchen window, etc.).

• Zone numbers are displayed at the keypad when an alarm or trouble condition

occurs on a sensor.

Arming, Step-Arming and Disarming Burglary Protection

• The system must be armed before the burglary protection can sense intrusions.

• To arm your system, enter your user code followed by the desired arming key.

• If programmed, the [#] key can be pressed instead of entering the security code

when arming the system.

• You can also use the step-arming key, if programmed, to arm the system, which

lets you use a function key to arm the system in one of three modes by simply

pressing the key repeatedly.

• To disarm the system, enter your user code then press the [OFF] key.

Alarms

• When an alarm occurs, both the keypad and external sounders will sound, and

the keypad will display the zone(s) causing the alarm.

• If your system is connected to a Central Monitoring Station, an alarm message

will also be sent.

• To stop the alarm sounding, simply disarm the system.

Memory of Alarm

• When an alarm condition occurs, the keypad displays the number(s) of the

zone(s) that caused the problem, and displays the type of alarm (e.g., “fire”).

• The message remains displayed even after disarming the system, but can be

cleared with another “off” sequence.

Phone Access

• If included, a phone module permits you to access the system via a touch-tone

phone, either on-premises or by calling-in when away.

• You can receive synthesized voice messages over the telephone regarding the

status of the security system.

• You can arm and disarm the system and perform most function commands

remotely via the telephone, with voice confirmation provided after each command

entry.

• Complete information regarding the use of this feature is provided in a separate

manual entitled “Phone Access User's Guide” that is supplied with the voice

module.

– 6 –

Download from Www.Somanuals.com. All Manuals Search And Download.

6\VWHPꢀ2YHUYLHZꢀꢁ&RQWLQXHGꢂ

Paging Feature

• If programmed, the system can automatically send certain system condition

messages to a pager.

• The display consists of code numbers that indicate the type of condition that has

occurred.

Function Keys

• The “A”, “B”, “C”, and “D” keys on the keypad can be programmed to perform

various functions.

• Functions include: activate a Panic alarm; arm the system; provide step arming;

switch lights on/off; send a message to a pager; display Time/Date; start a Macro

Scheduling

• Your system can be programmed to automatically perform certain functions (e.g.,

arm the system) at a predetermined time each day.

8VLQJꢁWKHꢁ9RLꢀHꢁ0HVVDJHꢁ&HQWHU

LEDS

The Voice Keypads feature a voice message center

LCD

DISPLAY

that lets you record and playback one message.

• The message can be up to 2.5-minutes long

ARMED READY MESSAGE

SPEAKER

• The message remains in the keypad’s memory

until a new message is recorded.

VOLUME

KEY

RECORD

KEY

PLAY KEY

AND

UP VOLUME

PLAY

• The volume control of the message is adjustable.

• Refer to the procedures below when using the

Message Center functions.

RECORD

VOLUME

FUNCTION

KEYS

DOWN

VOLUME

STATUS

VOICE

FUNCTION

KEY

FA560

MICROPHONE

STATUS

KEY

VOICE

KEY

FA560VKP-004-V0

Message Center Functions

To…

Press these keys…

Notes…

record a

message

The red MESSAGE LED lights.

Message remains in memory

until a new message is recorded.

[#] FUNCTION + [0] VOICE + [1] RECORD

end

recording

The red MESSAGE LED flashes,

indicating message waiting.

[1] RECORD

play a

message

The recorded message plays and

the red MESSAGE LED turns off.

[#] FUNCTION + [0] VOICE + [3] PLAY

adjust the

volume

Adjusting message volume also

adjusts status volume. Volume

cannot be adjusted while playing.

[#] FUNCTION + [0] VOICE + [2] VOLUME keys,

then press volume key [3] ↑ (up) or [6] ↓ (down)

– 7 –

Download from Www.Somanuals.com. All Manuals Search And Download.

$ERXWꢀ7KHꢀ.H\SDGV

*HQHUDOꢁ,QIRUPDWLRQ

Your keypads allow you to control all system functions. The keypads feature the

following:

• A telephone style (digital) keypad

• Liquid Crystal Display (LCD) which shows the nature and location of all

occurrences

• Built-in sounder which will sound during alarms and troubles. The sounder also

"beeps" during certain system functions and when depressing any of the keys (to

acknowledge the key press).

• Backlighting of the LCD display windows. Backlighting turns on when any key is

pressed, and when opening an entry/exit door while the system is armed. This

feature is helpful when a keypad is located in a dimly lit area.

IMPORTANT: If the keypad beeps rapidly upon entering the premises, it indicates

that an alarm has occurred during your absence and an intruder may still be on the

premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe

location.

Your keypads are functionally the same, but may have different types of displays,

depending on the type installed with your system.

Alpha Display

2-line alpha display keypads feature a 2-line, 32-character

alphanumeric LCD which can display system messages in

friendly English. These keypads can also be programmed with

custom zone descriptors.

Fixed-Word Display Fixed-Word display keypads are functionally identical to Alpha

display keypads, but the LCD display uses pre-designated

words to identify the nature and location of occurrences.

Voice Keypads

Voice Keypads (if installed), are functionally the same as other

keypads, except that these keypads can provide the following:

• Voice announcements of system status (see Checking for

Open Zones section)

• Voice chime, which can alert you to the opening of doors and

windows while the system is disarmed (see Voice Chime in

Chime mode section)

• Message center, which lets you record and playback

messages (see Using the Voice Message Center in the

System Overview section).

– 8 –

Download from Www.Somanuals.com. All Manuals Search And Download.

$ERXWꢀ7KHꢀ.H\SDGVꢀꢁ&RQWLQXHGꢂ

)L[HGꢁ:RUGꢀ'LVSOD\ꢀ.H\SDG

AWAY: All burglary zones, interior and

NIGHT NO AC

PHONE TEST

NOT READY

CHIME BAT

AWAY

perimeter, are armed.

BYPASS

STAY: Perimeter burglary zones, such as

protected windows and doors, are

armed.

ALARM STAY

CHECK INSTANT CANCELED

FIRE

6150disp

FA260KP

INSTANT: Entry delay is turned off:

Lit with STAY = Instant mode

AWAY

STAY

INSTANT

NO AC

CHIME

BAT

ALARM

CHECK

Lit with AWAY = Maximum mode

BYPASS CANCELED

NOT READY

FIRE NIGHT

BYPASS: This appears when one or more

burglary protection zones have been

bypassed.

FA215KP

FIXED-WORD DISPLAYS

NOT READY:

Appears when burglary portion of the system is not ready for arming

(due to open protection zones). The system is ready to arm when this

message disappears and the READY indicator light comes on.

NO AC: Appears when AC power has been cut off. System is operating on

backup battery power.

AC: Appears when AC power is present.

CHIME: Appears when the CHIME feature is activated.

BAT: Low battery condition in a wireless sensor (if zone number displayed)

or low system battery (if no zone number displayed).

ALARM: Appears when an intrusion has been detected and the system is armed

(also appears during a fire alarm or audible emergency alarm).

Accompanied by the protection zone in alarm.

CHECK: Appears when a malfunction is discovered in the system at any time or

if an open is detected in a FIRE zone at any time or a fault in a

DAY/NIGHT burglary zone during a disarmed period. Accompanied by

a display of zone number in trouble.

FIRE: Appears when a fire alarm is present. Accompanied by a display of the

zone in alarm.

A FIRE display also appears when a fire alarm is manually activated,

accompanied by a display of emergency key zone number programmed

for fire.

– 9 –

Download from Www.Somanuals.com. All Manuals Search And Download.

)XQꢃWLRQVꢀRIꢀWKHꢀ.H\SDGV

NOTE: The functions printed directly on the

6 BYPASS Removes individual protection zones from

keys indicate their primary purpose; the

functions printed under some of the keys

(shown in brackets under the respective key),

indicate their alternate or secondary purpose.

being monitored by the system.

[ ↓ ] On Voice keypads, used in conjunction with the

FUNCTION and VOLUME keys to lower the message

and voice system status volume.

DISPLAY WINDOW

7 INSTANT Arms in manner similar to the STAY

Alpha Display Keypads: 2-line, 32-character

Liquid Crystal Display (LCD) keypads that display

protection point identification, system status, and

messages.

mode, but without the entry delay feature.

KEYS 0–9: Used to enter your security code(s) and to

perform their associated system functions after the

security code has been entered.

Fixed-Word Display Keypads:

Display

protection zone ID and system status messages using

pre-designated words in the LCD display area.

✱ READY Used to display all open protection zones.

[STATUS]: On Voice keypads, a momentary press of the

STATUS key annunciates the current system status.

Pressing the STATUS key a second time annunciates and

displays system and/or zone faults (if they exist).

1 OFF

system,

Disarms burglary portion of the

silences alarms and audible trouble indicators, and

clears visual display after problem's correction.

[RECORD] On Voice keypads, used in conjunction

with the FUNCTION and VOICE keys to record up

to a 2.5-minute message.

[VOICE] On Voice keypads, enables the RECORD,

VOLUME and PLAY functions.

2 AWAY

Arms the entire burglary system,

This key can be used for "Quick Arming" of

perimeter and interior.

the system without use of a security code (if

programmed).

[FUNCTION] On Voice keypads, enables the desired

voice or volume function.

FUNCTION KEYS: Keys A, B, C, D may have been

programmed for a variety of functions, including panic

(emergency) functions. For details, see the Function Keys

section.

ARMED LED INDICATOR: (RED) Lit when the

system has been armed.

READY LED INDICATOR: (GREEN) Lit when the

system is ready to be armed (no faults present). While the

system is disarmed, this indicator will go on and off as

protection zones are closed and opened.

MESSAGE LED INDICATOR: (RED) On Voice

keypads, flashes red when message waiting or lights red

(steady) when in record mode.

[VOLUME] On Voice keypads, used in conjunction

with the FUNCTION and desired volume control

keys ↑ [3] or ↓ [6] to adjust the volume of a recorded

message or voice system status.

3 STAY

Arms perimeter portion of burglary

system only. Interior protection is not armed,

allowing movement within premises without causing

an alarm.

[PLAY] On Voice keypads, used in conjunction with

the FUNCTION and VOICE keys to play the

recorded message.

[ ↑ ] On Voice keypads, used in conjunction with the

FUNCTION and VOLUME keys to raise the

message and voice system status volume.

4 MAXIMUM Arms the entire burglary system,

perimeter and interior, but without entry delay

feature. Entering via an entry/exit door will cause an

alarm.

MIC: On voice keypads, microphone for Message Center

recordings.

INTERNAL SPEAKER: The built-in speaker mimics

the alarm sounder during alarms, and will also "beep"

during certain system functions. The speaker also

provides voice playback for any recorded messages.

5 TEST

Tests the system and alarm sounder if

disarmed. Refer to Testing The System section for

test procedures.

– 10 –

Download from Www.Somanuals.com. All Manuals Search And Download.

)XQꢃWLRQVꢀRIꢀWKHꢀ.H\SDGVꢀꢁ&RQWLQXHGꢂ

LEDS

LCD

DISPLAY

ARMED READY MESSAGE

SPEAKER

PLAY

RECORD

VOLUME

FUNCTION

KEYS

STATUS

VOICE

FUNCTION

FA560

FA560VKP-003-V0

MICROPHONE

Voice-capable 2-line Alpha keypad

IMPORTANT!

• When entering codes and commands, sequential key depressions must be made

within 4-5 seconds of one another. If 4-5 seconds elapse without a key depression, the

entry will be aborted and must be repeated from its beginning. Be sure to observe

this precaution when performing any of the procedures in this manual.

• If you make a mistake while entering a security code, stop, press the [✱] key, and

then start over. If you stop in the middle while entering a code, and then

immediately start the entry over, an erroneous code might be entered.

– 11 –

Download from Www.Somanuals.com. All Manuals Search And Download.

(QWU\ꢄ([LWꢀ'HOD\V

Your system has preset time delays, known as exit delay and entry delay.

([LWꢁ'HOD\

Exit delay gives you time to leave through the designated exit door without setting

off an alarm. Exit delay begins immediately after arming your system in any arming

mode and Alpha Display keypads display the message “You May Exit Now.” When

“You may exit now” disappears, the system is fully armed. If programmed, a slow

beeping will sound during the exit delay period until the last 10 seconds, which then

changes to fast beeping (alerting you to the end of exit delay). If you cannot leave by

this time, you should stop, disarm the system, and start over to avoid a false alarm.

Exit Delay Restart/Reset. If you wish to open the entry/exit door to let someone in

after arming STAY, you can re-start the exit delay at any time – simply press the

[✱] key, then let that person in. The system automatically re-arms when exit delay

expires, which avoids having to disarm the system and then re-arm it again.

In addition, when the system is armed AWAY, reopening and closing the entry/exit

door before exit delay time expires (e.g., reentering to get a forgotten item) will reset

the exit delay time.

(QWU\ꢁ'HOD\

Entry Delays give you time to disarm the system when you re-enter through the

designated entrance door. You must disarm the system (simply enter your security

code) before the entry delay period ends, or an alarm will occur. The keypad beeps

during the entry delay period, reminding you to disarm the system. There are two

entry delays (if programmed). The first is for your primary entrance and the second

can be used for a secondary entrance, where a longer delay is required to walk to the

keypad to disarm the system.

You can also arm the system with no entry delay at all by using the INSTANT or

MAXIMUM arming mode. This mode provides greater security while on the

premises or while away for extended periods of time.

See your installer for your delay times.

Exit Delay:

seconds

Entry Delay 1:

Entry Delay 2:

seconds

– 12 –

Download from Www.Somanuals.com. All Manuals Search And Download.

(QWU\ꢄ([LWꢀ'HOD\Vꢀꢁ&RQWLQXHGꢂ

([LWꢁ$ODUPV

Whenever you arm the system, the exit delay begins. If an entry/exit door or interior

zone is faulted within two minutes after the end of the exit delay (e.g., exit door left

open), the system sounds an alarm and starts the entry delay timer. If you disarm the

system before the entry delay ends, the alarm sound stops and the message

"CANCELED ALARM" or "CA" is displayed on the keypad, along with a zone number

indicating the faulted zone. No message is sent to the Central Monitoring Station.

To clear the exit alarm condition, the open zone must be made intact; to clear the

display, enter your code plus OFF.

If you do not disarm the system before the entry delay ends, and an entry/exit door or

interior zone is still open, the alarm sound continues and an "exit alarm" message is

sent to the Central Monitoring Station. The message ""EXIT ALARM" or "EA" is

displayed on the keypad, along with a zone number indicating the faulted zone. To

stop the alarm, the system must be disarmed (your code plus OFF); to clear the

display, enter your code plus OFF a second time.

Your system may have been programmed for this feature to minimize false alarms sent to the Central

Monitoring Station. Ask your installer if "Exit Alarm" is active in your system. If so, check this box.

– 13 –

Download from Www.Somanuals.com. All Manuals Search And Download.

&KHꢃNLQJꢀ)RUꢀ2SHQꢀ=RQHV

8VLQJꢁWKHꢁ>∗@ꢁ.H\

Before arming your system, all protected doors, windows and other protection zones

must be closed or bypassed, otherwise the keypad will display a "Not Ready" message.

1. Press [∗] READY (do not enter code first) to display

Alpha Display:

faulted zones.

∗

2. Secure or bypass the zones displayed.

3. The keypad’s READY indicator lights when all

protection zones have been either closed or bypassed.

4. Arm the system as desired.

Fixed-Word Display:

Zone no. and “NOT READY”

Voice Status: Voice Keypads (if installed), can announce system status and faulted

zones (up to 3 zone descriptors) if the Voice Status feature is turned on.

To turn the Voice Status feature on/off:

(also turns on Voice Chime mode; see Chime mode section)

To announce Status: Press [∗] STATUS key once.

To announce faulted zones: Press the [∗] STATUS key a second time within 5

seconds of the first press.

– 14 –

Download from Www.Somanuals.com. All Manuals Search And Download.

$UPLQJꢀWKHꢀ6\VWHP

6WD\ꢁ0RGHꢂꢁ$UPVꢁ3HULPHWHUꢁ2QO\ꢃꢁ(QWU\ꢁ'HOD\ꢁ2Q

• Used when you want to arm the system with persons staying inside (or if you have

pets that are moving throughout the premises).

• The perimeter sensors are armed, but interior sensors are left disarmed.

• Exit delay begins (you can leave through the entry/exit door, if desired).

• An alarm sounds if any protected window or non-entry/exit door is opened.

• You may otherwise move freely within the premises.

• Persons entering later can enter through an entry/exit door, but they must disarm

the system within the entry delay period to avoid sounding an alarm.

1LJKWꢄ6WD\ꢁ0RGHꢂꢁ$UPVꢁ3HULPHWHUꢁ2QO\ꢃꢁ3OXVꢁ6HOHꢀWHGꢁ=RQHV

• Use Night-Stay mode to provide increased security while staying inside.

• Arms same as Stay mode, but also arms pre-selected interior sensors (programmed

by your installer), while other interior sensors are left disarmed.

• Persons entering later can enter through an entry/exit door but they must disarm

the system and must not violate any of the programmed interior zones to avoid

sounding an alarm.

• IMPORTANT: When Night-Stay mode is on, the selected interior zones are armed and cause an

alarm if anyone enters those areas (e.g., waking in the middle of the night). To avoid sounding an

alarm, you must disarm the system before any activity takes place in those interior zones.

,QVWDQWꢁ0RGHꢂꢁ$UPVꢁ3HULPHWHUꢁ2QO\ꢃꢁ(QWU\ꢁ'HOD\ꢁ2II

• Used when staying inside and do not expect anyone to use an entry/exit door.

• Arms same as Stay mode.

• An alarm sounds immediately if any protected perimeter window or any door is

opened, including entry/exit doors.

• IMPORTANT: Arming in this mode greatly increases the chance of false alarms. Use extreme

care in selecting this mode of arming.

$ZD\ꢁ0RGHꢂꢁ$UPVꢁ(QWLUHꢁ6\VWHPꢃꢁ(QWU\ꢁ'HOD\ꢁ2Q

• Used when nobody will be staying inside (including pets).

• The entire system (interior and perimeter) is armed.

• Exit delay begins letting you leave through the entry/exit door.

• An alarm sounds if a protected window or any door is opened, or if any movement

is detected inside your premises.

• You can reenter through an entry/exit door, but you must disarm the system within

the entry delay period to avoid sounding an alarm.

0D[LPXPꢁ0RGHꢂꢁ$UPVꢁ(QWLUHꢁ6\VWHPꢃꢁ(QWU\ꢁ'HOD\ꢁ2II

• Used when leaving the premises for extended periods (e.g., vacation).

• Arms same as Away mode, but entry delay is off.

• An alarm sounds same as Away mode, and sounds upon opening entry/exit doors.

– 15 –

Download from Www.Somanuals.com. All Manuals Search And Download.

$UPLQJꢀWKHꢀ6\VWHP

$UPLQJꢁ&RPPDQGV

Before arming, close all perimeter doors and windows and make sure the Ready to Arm

message is displayed.

Modes of Arming

Mode

Stay

Press these keys…

security code + [3] (STAY)

Keypad Confirms By…

• three beeps

• armed STAY message displayed

• red ARMED indicator lights

• three beeps

Night-Stay security code + [3] + [3]

• NIGHT-STAY message displayed

• red ARMED indicator lights

• three beeps

• armed STAY message displayed

• red ARMED indicator lights

• also note that entry delay is turned off.

Instant

Away

security code + [7] (INSTANT)

security code + [2] (AWAY)

• two beeps, or, if programmed, beeping for

duration of exit delay

• armed AWAY message displayed

• red ARMED indicator lights

Leave the premises through an entry/exit

door during the exit delay period to avoid

causing an alarm. The keypad beeps rapidly

during the last 5 seconds of the exit delay to

warn you that it is ending.

Maximum

security code + [4] (MAXIMUM)

• same as Away (described above)

Note that entry delay is turned off.

Quick Arming

If "Quick Arming" was programmed by the installer, the [#] key can be pressed in

place of the security code when arming the system in any of its arming modes.

However, the security code must always be used to disarm the system.

Function Key Arming

For any arming command, a function key may have also been programmed for your

system. If so, you can press and hold the appropriate function key for 2 seconds to arm

the system. See your installer for the designated functions (see Single Button

Arming section).

– 16 –

Download from Www.Somanuals.com. All Manuals Search And Download.

$UPLQJꢀWKHꢀ6\VWHP

6LQJOHꢁ%XWWRQꢁ$UPLQJ

The “A”, “B”, “C”, and/or “D” keys on your keypad may have been programmed for

single-button arming. Note that while it will not be necessary to use a security code

for arming, a security code must always be used to disarm the system.

If Single-Button Arming is programmed:

• A function key has been assigned to a specific type of arming: STAY mode,

Night-STAY mode, AWAY mode, or STEP-ARMING (see Step-Arming

paragraph).

• You DO NOT need to enter your security code before pressing the function key

(but you always need your security code to DISARM the system).

Before arming, close all perimeter doors and windows.

Alpha Display:

1. Press and hold the assigned function key for 2

seconds (no code is required). Function keys are

shown below.

Fixed-Word Display: READY

2. The keypad begins beeping and displays the armed

Alpha Display:

message. The red ARMED indicator also lights.

Fixed-Word Display: AWAY

6WHSꢁ$UPLQJꢁ)HDWXUH

Single-Button “Step” arming may have been programmed into one of the lettered keys

(A, B, C, or D). Check with your installer to see if this has been done in your system.

If Step-Arming is programmed:

• The assigned key provides a choice of three levels of security.

• The selected key can be pressed once, twice, or three times, increasing the level

of security with each press, as follows

Key

First Press

Second Press

Third Press

Armed-STAY

Armed Night-STAY

(if programmed)

Armed-AWAY

A, B, C, D

– 17 –

Download from Www.Somanuals.com. All Manuals Search And Download.

8VLQJꢀWKHꢀ.H\VZLWꢃK

8VLQJꢁWKHꢁ.H\VZLWꢀK

Your system may be equipped with a keyswitch for use when arming and disarming.

Red and green lights on the keyswitch plate indicate the status of your system as

follows:

Green Light: Lights when the system is disarmed and ready to be armed (no

open zones). If the system is disarmed and the green light is off, it

indicates the system is not ready (one or more zones are open).

Red Light:

Lights or flashes when system is armed in AWAY or STAY mode.

See your installer for the meanings of the lit red light:

Lit Steady = system armed AWAY or

system armed STAY and exit delay has expired

Flashing = system armed STAY and exit delay timer active

Rapid flashing = an alarm has occurred (memory of alarm).

Before arming, close all perimeter doors and windows.

To arm in the AWAY mode:

Turn the key to the right for 1/2 second and release.

Keypads beep twice and the red indicator lights or

flashes.

GREEN

RED

To arm in the STAY mode:

Turn the key to the right and hold for longer than 1

second, then release. Keypads beep three times and

the red indicator lights or flashes.

To disarm the system:

Turn the key to the right and release. The red light

turns off

– 18 –

Download from Www.Somanuals.com. All Manuals Search And Download.

'LVDUPLQJꢀDQGꢀ6LOHQꢃLQJꢀ$ODUPV

8VLQJꢁWKHꢁ>2))@ꢁNH\

The OFF key is used to disarm the system, silence alarm and trouble sounds, and

clear alarm memories.

IMPORTANT: If you return and the main burglary sounder is on, DO NOT ENTER, but

CONTACT THE POLICE from a nearby safe location.

If you return after an alarm has occurred and the main sounder has shut itself off, the keypad will

beep rapidly upon your entering, indicating that an alarm has occurred during your

absence.

LEAVE AT ONCE, and CONTACT THE POLICE from a nearby safe location.

Alpha Display:

(Security Code)

OFF

The “READY” indicator light will be lit if all zones

are secure, and the keypad will emit a single tone to

confirm that the system is disarmed.

Fixed-Word Display: READY

NOTE: If entry delay has started (you’ve opened the

entry door), you do not need to press the OFF key;

simply enter your security code.

2. To Silence a Burglary Alarm and Clear a Memory of Alarm

Enter your security code. This disarms the system and silences the alarm (or

warning tones of a Memory of Alarm).

Note the zone in alarm on the keypad display, and make that zone intact (close

door, window, etc.). Now enter the security code plus OFF to clear the keypad’s

Memory of Alarm display.

3. To Silence a Fire Alarm and Clear Memory of Alarm

Simply press the OFF key to silence the alarm. Then enter the security code plus

OFF sequence to clear the keypad's Memory of Alarm display. See the Fire Alarm

System section.

– 19 –

Download from Www.Somanuals.com. All Manuals Search And Download.

%\SDVVLQJꢀ3URWHꢃWLRQꢀ=RQHV

8VLQJꢁWKHꢁ%<3$66ꢁ.H\

Use this key when you want to arm your system with one or more zones intentionally

unprotected.

Vent Zones: Your system may have certain windows set as “vent” zones, which are

automatically bypassed if left open when arming the system (you do not need to

manually bypass them). However, if a vent zone window is closed after arming, it

becomes protected and will cause an alarm if opened again while the system is armed.

When bypassing zones:

• The system must be disarmed before you can bypass zones.

• Bypassed zones are unprotected and will not cause an alarm if violated.

• The system will not allow fire zones to be bypassed.

• Zones are automatically unbypassed when the system is disarmed.

Alpha Display:

6 + zone numbers (see below)

(Security Code)

BYPASS

Enter the 2-digit zone number(s) for the zone(s) to be

bypassed (e.g., 06, 10, 13, etc.). Single digit zone

numbers must be preceded by a zero (e.g. 05, 06).

Fixed-Word Display: NOT READY

2. When finished, the keypad will momentarily display

a "Bypass" message for each bypassed zone number.

Wait for all bypassed zones to be displayed.

Alpha Display:

Arm the system as usual. When armed, the arming

message is displayed with “ZONE BYPASSED.”

Fixed-Word Display: BYPASS

To display bypassed zones prior to arming, enter

your security code and press the [6] BYPASS key.

Typical armed alpha display after

bypassing zones.

– 20 –

Download from Www.Somanuals.com. All Manuals Search And Download.

%\SDVVLQJꢀ3URWHꢃWLRQꢀ=RQHV

4XLꢀNꢁ%\SDVV

If programmed, "Quick Bypass" allows you to easily bypass all open (faulted) zones

without having to enter zone numbers individually. This feature is useful if, for

example, you routinely leave certain windows open when arming at night.

Alpha Display:

6 + [#]

(Security Code)

BYPASS

In a few moments, all open zones will be displayed

and automatically bypassed. Make sure that only those

zones that you wish to leave unprotected are bypassed, and

that there are no other zones unintentionally left open.

NOT READY

Fixed-Word Display:

2. Wait for all bypassed zones to be displayed, then arm

the system as desired.

Ask your installer if "Quick Bypass" is active for your

Fixed-Word Display: BYPASS

system, and if so, check here:

– 21 –

Download from Www.Somanuals.com. All Manuals Search And Download.

&KLPHꢀ0RGH

CHIME mode alerts you to the opening of a perimeter door or window while the

system is disarmed. When Chime mode is activated:

• Three tones sound at the keypad whenever a perimeter door or window is opened.

• Interior zones do not produce a tone when they are faulted.

• Pressing the READY key will display the open protection points.

• Chime mode can be used only while the system is disarmed.

To turn Chime Mode on/off (system must be disarmed):

(Security Code)

CHIME

Fixed-Word Display: CHIME

The CHIME message appears when on. Perimeter

zones will cause a tone when faulted.

The CHIME message disappears when Chime mode is off.

Voice Chime: You can set the Voice Keypads (if installed) to announce faulted

(opened) entry/exit or perimeter zones whenever normal Chime mode is on.

To turn Voice Chime Mode on or off:

(normal Chime mode must be on first)

When Voice Chime is on, faulted zones cause a voice status announcement, chime

and display. When off, the sounder still provides chime if normal Chime mode is on.

– 22 –

Download from Www.Somanuals.com. All Manuals Search And Download.

ꢀ'DWHꢀDQGꢀ7LPH

9LHZLQJꢁWKHꢁ&XUUHQWꢁ'DWHꢁDQGꢁ7LPH

The system lets you view its time and date setting on alpha keypad.

Alpha Display:

+[#] + [6] [3]

(Security Code)

OR, press the function key (A, B, C, or D) for viewing

current date and time, if programmed.

A typical time/date display is shown.

The display will remain on for about 30 seconds.

“A”

“ B”

“ C”

“ D”

If one of the above keys has been programmed for the date/time

display feature, place a check mark in the box beneath that key.

6HWWLQJꢁWKHꢁ'DWHꢁDQGꢁ7LPH

You can set the time and date by doing the following:

1. +[#] + [6] [3]

Alpha Display:

(Security Code)

2. Press [∗] when the time/date is displayed.

A cursor appears under the first digit of the hour.

To move cursor ahead, press [∗]. To go back, press [#].

• Enter the 2-digit hour setting.

Current time display

• Enter the 2-digit minute setting.

• Press [1] for PM or [0] for AM.

• Enter the last two digits of the current year.

• Enter the 2-digit month setting.

• Enter the 2-digit day setting.

Time/date editing display

3. To exit, press [∗] when cursor is at the last digit, or

wait 10 seconds.

– 23 –

Download from Www.Somanuals.com. All Manuals Search And Download.

3DQLꢃꢀ.H\V

8VLQJꢁ3DQLꢀꢁ.H\V

Your system may have been programmed to use special keys to manually activate

emergency (panic) functions as follows:

This Function

Sends this signal* With This Sounding…

Silent Alarm

silent alarm

no audible alarm and no change in

normal display to indicate that a silent

alarm has been initiated.

Audible Alarm

audible alarm

a loud, steady alarm at keypad(s) and at

any external sounders that may be

connected.

Personal Emergency auxiliary alarm

Fire Alarm fire alarm

steady alarm sound at keypad(s), but not

at external bells or sirens.

temporal (pulsing) sound at external

bells and sirens.

*All panic functions send signals to the Central Monitoring Station, if connected.

To activate a Panic Function:

Alpha Display:

Press and hold down for at least 2 seconds whichever

lettered key on the keypad has been programmed for

the desired emergency function.

Fixed-Word Display: READY

Typical Panic Alpha Display:

Press both keys of the assigned key pair at the same

time.

Fixed-Word Display: 99 and ALARM

ARMED READY

PRESS BOTH KEYS

OF DESIRED PAIR

ARMED READY

ZONE 95

AT THE SAME TIME

AWAY

STAY

ZONE 99

ZONE 95

ZONE 96

AWAY

PAGE

STAY

FA560

ZONE 96

PAGE

FA560

ZONE

Lettered Panic Keys

Panic Key Pairs

See your installer and use the chart provided in the Features Programmed in Your

System section to note the functions that have been programmed for your system.

– 24 –

Download from Www.Somanuals.com. All Manuals Search And Download.

0DꢃURꢀ.H\ꢀ3URJUDPPLQJꢀ ꢀ8VDJH

$ERXWꢁ0DꢀURꢁ.H\V

The “A”, “B”, “C” or “D” keys can be used to automatically activate a series of

commands of up to 16 keystrokes, if programmed for this function. These keystrokes,

as a group, are called “macros” and are stored in the system's memory.

• Typical macro functions can include:

- Arming sequences: STAY, Night-STAY, INSTANT, or AWAY

- Bypassing particular zone(s)

- Activating relay(s) for turning on (or off) lights, fans, etc.

• One macro can be assigned.

• Macros can be activated only by users with authority levels authorized to

perform the macro’s function.

NOTE: The installer must activate the desired function key before macros can be

assigned. See the chart at the back of this manual for the key(s) assigned for macros.

Alpha Displays:

+ [#] + [6] + [6]

(Security Code)

If a macro has been previously defined, the

keystrokes are shown on the bottom line of the

display, otherwise the display is blank.

To exit this mode (and keep the existing macro

definition), press any key except the [∗] key. The

system returns to normal mode.

To define a macro for the selected key, press [∗] and

continue with the next prompt.

2. Enter the first of the series of desired commands, (do

not include your user code), then press/hold the “D”

key for at least two seconds to complete the first

command. This key terminates each command, and

appears as an “F” in the keypad display.

– 25 –

Download from Www.Somanuals.com. All Manuals Search And Download.

0DꢃURꢀ.H\ꢀ3URJUDPPLQJꢀ ꢀ8VDJHꢀꢁꢃRQWꢅꢂ

Typical Macro Alpha Display:

The keypad beeps to acknowledge your input and

displays the command you entered (followed by “F”).

4. Enter the next command, followed by press/holding

ꢀ ꢁ ꢂ ꢁ ꢃ * ^#ꢄ ꢁ ꢅ * ꢂ *

the “D” key for at least two seconds. The keypad

beeps and displays the keystrokes entered so far.

5. Repeat until the all the desired commands (up to 16

characters including the “F”s) have been entered.

Be sure to check your keystrokes before continuing.

If you made a mistake, you must start over.

6. To exit, press/hold the “D” key for at least two

seconds. The display returns to system status and

indicates system is ready.

([DPSOHꢁRIꢁ0DꢀURꢁ3URJUDPPLQJ

Suppose you want to (1) bypass the two upstairs window zones, then (2) turn on an

exterior light, and then (3) arm the security system in the AWAY mode. The

procedures in the table that follows show you how you would program this macro:

Function

Keystrokes Required

Keypad Display

1. Bypass zones 02 & 03

Press BYPASS [6] key, then

ꢀ ꢁ ꢂ ꢁ ꢃ

2-digit zone numbers 02 & 03.

2. Insert terminator.

Press the “D” key for at least 2 seconds.

ꢀ ꢁ ꢂ ꢁ ꢃ *

3. Turn light on

(device 01).

Press [#] and 7 keys for “device ON”, and

[01] key for selecting device 1.

ꢀ ꢁ ꢂ ꢁ ꢃ * ꢄ ꢁ ꢅ

4. Insert terminator.

Press the “D” key for at least 2 seconds.

ꢀ ꢁ ꢂ ꢁ ꢃ * ^#ꢄ ꢁ ꢅ *

ꢀ ꢁ ꢂ ꢁ ꢃ * ^#ꢄ ꢁ ꢅ * ꢂ

ꢀ ꢁ ꢂ ꢁ ꢃ * ^#ꢄ ꢁ ꢅ * ꢂ *

5. Arm system AWAY

6. Insert terminator.

Press AWAY [2] key.

Press the “D” key for at least 2 seconds.

8VLQJꢁDꢁ3URJUDPPHGꢁ0DꢀURꢁ.H\

Press the Macro key programmed for the desired

series of commands for at least 2 seconds. The “Enter

User Code” prompt appears. The prompt remains

displayed for up to 10 seconds.

2. Enter your 4-digit user code.

The programmed macro sequence begins

automatically after the user code is entered.

– 26 –

Download from Www.Somanuals.com. All Manuals Search And Download.

8VLQJꢀ'HYLꢃHꢀ&RPPDQGV

$ERXWꢁ'HYLꢀHꢁ&RPPDQGV

Your system may be set up so that it can control certain lights or other devices.

• Some devices may be automatically turned on or off by the system.

• You may be able to override automatically controlled devices using the

commands described below.

• Some devices can be manually turned on or off using the commands described

below.

• See your installer for a list of devices that may be set up for your system. A list

of these devices is provided at the back of this manual for you to fill out.

To Activate Devices:

+ [#] + [7] + 2-digit device number

Alpha Display:

(Security Code)

Devices associated with that device number activate.

Fixed-Word Display: READY

To Deactivate Devices:

+ [#] + [8] + 2-digit device number

(Security Code)

Devices associated with that device number deactivate.

– 27 –

Download from Www.Somanuals.com. All Manuals Search And Download.

3DJLQJꢀ)HDWXUH

$ERXWꢁ$XWRPDWLꢀꢁ3DJLQJ

Your system may be set up to automatically send alert messages to a pager as certain

conditions occur in your system.

• The following events can be programmed by your installer to be sent to the pagers:

arming and disarming^†, alarms, and trouble conditions. († reports when

arming/disarming from a keypad using a security code; auto-arming/disarming,

arming with assigned button, and keyswitch arming do not send pager messages.)

• You can also program the system to send an automatic pager message to alert you

in the event that someone has not arrived home (disarmed the system) within a

defined period of time (see the Scheduling section for details on “latch key report”).

• Your installer programs the pager phone numbers and reporting events.

• The pager message consists of a 7-digit system status code that indicates the type of

condition that has occurred.

• An optional, predefined 16-digit character string can precede the 7-digit system

status code; these characters can consist of a PIN no., subscriber account no., or any

additional data that you may wish to have sent to the pager.

• The pager display format is as follows:

3-digit Event Code

Optional 16 digits

AAAAAAAAAAAAAAAA – BBB – CCCC

1-digit partition + 3-digit User or Zone No.

A =

B =

C =

A 1-digit partition number plus a 3-digit User or Zone

number, depending on the type of event that has

occurred, where:

• alarms and troubles display zone number

• arming/disarming (opens/closes) display user number

• single-digit user or zone numbers are preceded by a

zero.

Optional 16-digits for A 3-digit code that

Account numbers,

PIN numbers, or any

other data;

describes the event

that has occurred

in your system

programmed by the

installer, if required.

(see for event

codes table below)

The 3-digit Event Codes (BBB) that can be displayed are:

911 =

811 =

101 =

102 =

Alarms.

Troubles.

Open

The 4-digit number

(CCCC) represents the

zone number that has

caused the alarm.

The 4-digit number

(CCCC) represents the

zone number that has

caused the trouble.

(system disarmed).

The 4-digit number

(CCCC) represents the

user number that has

disarmed the system.

(system armed).

The 4-digit number

(CCCC) represents the

user number that has

armed the system.

Examples of typical 7-digit pager displays follow.

Ex. 1.

Ex. 2.

= Alarm (911) on zone 4 (1004)

= Closing–system arming (102)– by user 5 (1005)

– 28 –

Download from Www.Somanuals.com. All Manuals Search And Download.

3DJLQJꢀ)HDWXUH

0DQXDOꢁ3DJLQJ

Your system may be set up so you can manually send a message to a pager.

• Your installer programs the paging function key and the pager phone number.

• Pressing the paging keys sends the message 9 9 9 – 9 9 9 9 to the pager.

• This message could mean “call home”, “call your office”, or any other prearranged

meaning.

• See the Paging chart at the back of this manual for details of the paging setup for

your system.

Alpha Display:

1. Hold pager key 2 seconds.

Press and hold the programmed Paging Key for at

least 2 seconds (wait for beep).

2. The recipient, on seeing the 999–9999 message, will

understand the prearranged meaning of this signal.

Fixed-Word Display: READY

Pager Display

/DWꢀKꢁ.H\ꢁ3DJLQJ

You can program a schedule that causes a pager report to be sent if the system is not

DISARMED by the scheduled time (see Scheduling section, event “03”). For example,

a working parent might want a message to be sent to a pager if their child did not

arrive home from school and disarm the system by a certain time.

If programmed, the message that is sent is: 7 7 7 – 7 7 7 7

– 29 –

Download from Www.Somanuals.com. All Manuals Search And Download.

6HꢃXULW\ꢀ&RGHVꢀ ꢀ$XWKRULW\ꢀ/HYHOV

$ERXWꢁ6HꢀXULW\ꢁ&RGHV

Your installer assigned a master code that is used to perform all system functions.

In addition, you can assign up to 15 different security codes for use by other users.

• Only the System Master can assign user codes to users.

• Users are identified by 2-digit user numbers (01-16).

• In addition to a security code, each user is assigned various system attributes.

• User codes can be used interchangeably when performing system functions (a

system armed with one user's code can be disarmed by another user's code), with

the exception of the guest code described below.

• User code programming involves these steps:

1. Choose a user number and assign a 4-digit security code.

2. Assign an authority level to that user.

3. Assign other attributes as necessary (see attributes on the next page).

NOTE: The factory settings are designed to meet most normal user situations.

Therefore, the only step you usually need to do when adding users is assign a user

number and a security code.

$XWKRULW\ꢁ/HYHOꢁ'HILQLWLRQV

Authority levels define the system functions a particular user can/cannot perform.

Level Title

N/A

Explanation

System Master Reserved for user 02; Can perform all system functions and assign

codes; can change its own code as follows:

Master code + [8] + 02 + new master code + new master code again

The default System Master code is 1234.

Standard User Can only perform security functions. Cannot perform other system

functions.

Arm Only

Guest

Can only arm the system. Cannot disarm or do other functions.

Can arm the system, but cannot disarm the system unless the

system was armed with this code. This code is typically assigned to

someone (e.g., babysitter or cleaner) who has a need to arm/disarm

the system only at certain times. The user of this code should not use

the “Quick Arming” feature.

Duress Code

Intended for use when you are forced to disarm or arm the system

under threat. When used, the system will act normally, but can

silently notify the Central Monitoring Station of your situation, if that

service has been provided.

– 30 –

Download from Www.Somanuals.com. All Manuals Search And Download.

6HꢃXULW\ꢀ&RGHVꢀ ꢀ$XWKRULW\ꢀ/HYHOVꢀꢁ&RQWꢅꢂ

+RZꢁWRꢁ$VVLJQꢁ8VHUꢁ&RGHVꢁDQGꢁ$WWULEXWHV

The following lists the various command strings for adding user codes and attributes.

Refer to the User Setup chart at the back of this manual for factory

assignments of user attributes and to keep a record of user programming.

Add User Code:

System Master code + [8] + user no. + new user’s code

User 01 = installer

User 02 = master

User 03-16 = standard users

(factory set master code is 1234)

The Keypad beeps once to confirm that new user was added.

Delete User Code:

Authority Level:

System Master code + [8] + [user no.] + [#] [0]

The user code and all attributes programmed for this user number,

including any associated RF keys, are erased from the system.

System Master code + [8] + [user no.] + [#] [1]+ auth. level

Factory Assignments:

users 03-16 = 0

Authority Levels (see definitions on previous page):

0 = standard user

1 = arm only

2 = guest

3 = duress

Access Group:

System Master Code + [8] + [user no.] + [#] [2]+ group (1-8)

Factory Assignments: none

You can assign users to a group, then set an access schedule that

defines the times this group of users can operate the system. The

system ignores these users outside the scheduled times.

RF User Number:

System Master Code + [8] + [user no.] + [#] [4]+ zone no.

Factory Assignments: none

Use this command to assign a wireless button device (keyfob) to this

user (keyfob must be enrolled in system first; see installer).

Zone number: enter the zone number assigned to a button on the

keyfob that will be used for arming/disarming by this user.

Pager On/Off:

System Master Code + [8] + [user no.] + [#] [5] + 0 or 1

Factory Assignments:

users 01-16 = 1 (on)

You can program a user so that a message is sent to a pager

whenever this code is used to arm or disarm the system.

Paging On/Off: 1 = allow paging; 0 = no paging for this user

– 31 –

Download from Www.Somanuals.com. All Manuals Search And Download.

6ꢃKHGXOLQJ

$ERXWꢁ6ꢀKHGXOLQJ

The system provides one end-user schedule (programmable by master/installer only),

which can control various types of events.

• Each schedule causes a defined event to start and stop (when appropriate) at a

specified time.

• Schedules can be set to automatically repeat at various intervals.

• Schedules can be set for random starting, if desired.

&UHDWLQJꢁ6ꢀKHGXOHV

Alpha Displays:

+ [#] + [6] [4]

(Master Code)

2. Enter “01” as the 2-digit schedule number.

Press [∗] to continue.

3. Enter the desired 2-digit event number from the

following list.

00 = clear the scheduled event

01 = turn a programmed output on or off

(see Using Device Commands section for a list of output device numbers used

in your system)

02 = set a user access schedule for one or more users

(see Security Codes section for an explanation of access groups)

03 = send a “latch-key” report to a pager if the system is not disarmed by a specified

time; message sent is “777-7777.”

04 = automatically arm the system in STAY mode at a specified time

05 = automatically arm the system in AWAY mode at a specified time

06 = automatically disarm the system at a specified time

07 = Display the word “REMINDER” at a specified time

Press [∗] to continue.

4. For event number “01,” enter the output number

associated with this schedule.

Otherwise, this prompt is skipped.

Press [∗] to continue to the “Start” prompt below.

– 32 –

Download from Www.Somanuals.com. All Manuals Search And Download.

6ꢃKHGXOLQJꢀꢁꢃRQWLQXHGꢂ

5. For event number “02,” enter the access group

number. Otherwise, this prompt is skipped.

Press [∗] to continue to the “Start” prompt below.

7. Enter the event’s start time and days of week.

Hour = 00-12; minute = 00-59

AM = 0; PM = 1

Days = Position the cursor under the desired days

using the [∗] key to move forward, then press “1” to

select the day.

Press [∗] to continue.

8. Enter the event’s stop time, AM/PM and days of

week.

Refer to step 7 for available entries.

Press [∗] to continue.

9. Enter the desired repeat option.

0 = no repeat

1 = repeat schedule weekly

2 = repeat schedule biweekly (every other week)

3 = repeat schedule every third week

4 = repeat schedule every fourth week

e.g., To make a schedule that happens everyday you

would select all days with a repeat count of 1. To

make a schedule that runs for one week then stops,

select everyday with a repeat count of 0.

10. Select the randomize option, if desired.

0 = no; 1 = yes

If selected, the schedule times will vary within 60

minutes of the “hour” time. For example, if a

schedule is set to start at 6:15pm, it will do so the

first time 6:15pm arrives, but on subsequent days it

will start anytime between 6:00 and 6:59 p.m.

Press [∗] to return to first prompt, then enter 00 to

quit.

– 33 –

Download from Www.Somanuals.com. All Manuals Search And Download.

(YHQWꢀ/RJJLQJꢀ3URꢃHGXUHV

$ERXWꢁ(YHQWꢁ/RJJLQJ

The system records various events in a history log, which can be viewed by the master

user using an Alpha Display keypad.

• The Event Log holds up to 32 events.

• Events are displayed in chronological order, from most recent to oldest.

• When the log is full, the oldest event is replaced by the logging of any new event.

9LHZLQJꢁWKHꢁ(YHQWꢁ/RJ

Alpha Displays:

+ [#] + 6 + 0

(Master Code)

2. The system displays the most recent event as follows:

• event number

• type of event, identified by its corresponding code

(see your installer for the meaning of each code)

• zone or user number (depending on type of event)

• time and date of the event’s occurrence.

3. Pressing [∗] displays previous events (back in time).

Pressing [#] displays events forward in time.

4. Exit the event log by pressing any key other than [∗]

or [#].

– 34 –

Download from Www.Somanuals.com. All Manuals Search And Download.

(YHQWꢀ/RJJLQJꢀ3URꢃHGXUHVꢀꢁꢃRQWLQXHGꢂ

7DEOHꢁRIꢁ(YHQWꢁ/RJꢁ&RGHV

The following table lists the codes that may appear when viewing the Event Log.

If the event code is preceded by an “E” (as in the example display on the previous

page), it means that the event is new and ongoing; if preceded by an “R,” it means the

event has been restored.

Code

110

121

122

123

Definition

Fire Alarm

Duress

Alarm, 24-hour Silent

Alarm, 24-hour Audible

Code

Definition

381

382

383

384

393

401

RF Supervision Trouble

Supervision Auxiliary Wire Zone

RF Sensor Tamper

RF Sensor Low-battery

Clean Me

Disarmed, Armed AWAY,

Armed STAY

Schedule Arm/Disarm AWAY

Cancel by User

Remote Arm/Disarm

(Downloading)

Quick Arm AWAY

Keyswitch Arm/Disarm AWAY

Disarmed/Armed

STAY/INSTANT,

Quick-Arm STAY/INSTANT

Keyswitch Arm/Disarm STAY

Bypass

Manually Triggered Dialer Test

Periodic Test

AAV to Follow

Walk Test Entered/Exited

Event Log 80% Full

131

132

134

135

Alarm, Perimeter

Alarm, Interior

Alarm, Entry/Exit

Alarm, Day/Night

403

406

407

143

145

146

150

Alarm, Expansion Module

ECP Module cover tamper

Silent Burglary

Alarm, 24-Hour Auxiliary/Monitor

zone

Carbon Monoxide

AC Power

Low System Battery/Battery Test

Fail

System Reset (Log only)

Battery Test Failure

Bell/Siren Trouble

Trouble, Expansion Mod.

Supervision

Trouble, ECP Cover Tamper

RF Receiver Jam

Telco Line Fault

408

409

441

162

301

302

442

570

601

602

606

607

623

625

305

309

321

333

Real-Time Clock was Changed

(log only)

341

344

351

353

373

374

380

627

628

750 -

789

Program Mode Entry (log only)

Program Mode Exit (log only)

Reserved for Configurable Zone

Type report codes (check with

central station when using these

codes)

Long Range Radio Trouble

Fire Loop Trouble

Exit Error Alarm

Global Trouble, Trouble

Day/Night

– 35 –

Download from Www.Somanuals.com. All Manuals Search And Download.

7HVWLQJꢀWKHꢀ6\VWHPꢀꢁ7Rꢀ%Hꢀ&RQGXꢃWHGꢀ:HHNO\ꢂ

$ERXWꢁ7HVWLQJꢁWKHꢁ6\VWHP

Using Test mode allows each protection point to be checked for proper operation.

• The keypad sounds a single beep every 40 seconds as a reminder that the

system is in the Test mode.

• Alarm messages are not sent to your Central Station while Test mode is on.

Alpha Displays:

1. Disarm the system and close all protected windows,

doors, etc. The READY indicator light should come

on if all zones are intact (i.e., all protected windows,

doors, etc. are closed.

then [0] (walk)

TEST

(Security Code)

The Dial test (option “1”) is intended for the installer

and should not be used unless directed to do so by

your Security System Representative.

3. Listen. The external sounder should sound for 1

second and then turn off. If the sounder does not

sound, CALL FOR SERVICE.

4. Fault zones. Open each protected door and window in turn and listen for three

beeps from the keypad. Identification (zone number or zone description) of each

faulted protection point should appear on the display. The display clears when the

door or window is closed.

5. Walk in front of any interior motion detectors (if used) and listen for three beeps.

The identification of the detector should appear on the display when it is activated.

The display clears when no motion is detected.

Note that if wireless motion detectors are used, there is a 3-minute delay between

activations. This is to conserve battery life.

6. Test all smoke detectors, following the manufacturer's instructions. The

identification of each detector should appear on the display when each is activated.

If a problem is experienced with any protection point (no confirming sounds, no

display), call for service immediately.

When all protection points have been checked and are intact (closed), there should

be no zone identification numbers displayed on the keypad.

7. Exit test mode:

+ [ 1 ]

(Security Code)

If the test mode is inadvertently left active, it automatically turns off after 4 hours.

– 36 –

Download from Www.Somanuals.com. All Manuals Search And Download.

7URXEOHꢀ&RQGLWLRQV

"Check" and

"Battery" Displays

The word CHECK on the keypad's display, accompanied by a

"beeping" at the keypad, indicates a trouble condition in the system.

To silence the beeping for these conditions, press any key.

1. A display of "CHECK" and one or more zone numbers

indicates that a problem exists with the displayed zone(s) and

requires your attention. Determine if the zone(s) displayed are

intact and make them so if they are not. If the problem has been

corrected, the display can be cleared if you enter the OFF

sequence (security code plus OFF key) twice. If the display

persists, CALL FOR SERVICE.

Note: A display of CHECK 70 on Alpha Display keypads

indicates that the wiring connection to the external sounder is

at fault (opened or shorted), and you should CALL FOR

SERVICE. See “BELL FAILURE” on next page. A display of

CHECK 90 indicates that RF interference may be impeding the

operation of wireless sensors* in the system. See “Rcvr Jam”

on next page.

2. If there are wireless sensors* in your system, the CHECK

condition may also be caused by some change in the

environment that prevents the wireless receiver from receiving

messages from a particular sensor. CALL FOR SERVICE if this

occurs.

* Not all systems

use wireless

sensors.

IF YOU CANNOT CORRECT A "CHECK" DISPLAY,

CALL FOR SERVICE.

TYPICAL "CHECK" DISPLAYS

' , ) ' / ꢆ ꢁ ꢀ

& ) ( 6 3 3 1 ꢆ ; - 2 ( 3 ;

CHECK

ALPHA DISPLAY KEYPAD

FIXED-WORD DISPLAY KEYPAD

– 37 –

Download from Www.Somanuals.com. All Manuals Search And Download.

7URXEOHꢀ&RQGLWLRQVꢀꢁ&RQWLQXHGꢂ

Words or letters in parentheses ( ) are those that are

displayed on Alpha Display keypads.

COMM. FAILURE

(or FC)

Indicates that a failure has occurred in

the telephone communication portion of

your system.

Other Trouble

Displays

CALL FOR SERVICE.

* Any “beeping” that

accompanies a trouble

display can be stopped

by depressing any key

on the keypad or by

entering an OFF

SYSTEM LO BAT

(or BAT with no

zone No.)

Indicates that a low system battery

condition exists. Display is

accompanied by "beeping"* at the

keypad. If this condition persists for

more than one day (with AC present),

CALL FOR SERVICE.

sequence (code + OFF)

LO BAT

Indicates that there is a low battery

condition in the wireless transmitter**

number displayed (00 is RF keypad).

+ zone descriptor

(or BAT with

zone No.)

** Not all systems use

wireless sensors.

Accompanied by a single "beep" (about

once every 40 seconds) at the keypad.

Either replace the battery yourself, or

CALL FOR SERVICE. If the battery is

not replaced within 30 days, a CHECK

display may occur.

Rcvr Jam

(or CHECK 90)

Wireless part of the system is experiencing

RF interference which may impede

reception from wireless sensors.**

MODEM COMM

(or CC)

Indicates that the control is on-line with

the Central Monitoring Station's remote

computer.

The control will not operate while on-line.

Wait a few minutes — the display should

disappear.

BELL FAILURE

(or CHECK 70)

Indicates that the wiring connection to

the external sounder is at fault (open or

shorted). Accompanied by “beeping” at

the keypad. CALL FOR SERVICE.

– 38 –

Download from Www.Somanuals.com. All Manuals Search And Download.

7URXEOHꢀ&RQGLWLRQVꢀꢁ&RQWLQXHGꢂ

Other Trouble

Displays

(Continued)

AC LOSS

(or NO AC)

The system is operating on battery power

only due to an AC power failure.

If only some lights are out on the premises,

check circuit breakers and fuses and

reset or replace as necessary.

If AC power cannot be restored and a

“low system battery” message appears

(see previous page), CALL FOR

SERVICE.

Busy-Standby

(or dI)

If this message remains displayed for more

than 1 minute, system is disabled. CALL

FOR SERVICE.

OPEN CIRCUIT

(or OC)

The keypad is not receiving signals from

the control. CALL FOR SERVICE.

Long Rng Trbl

(or bF)

If part of your system, back-up Long

Range Radio communication has failed.

CALL FOR SERVICE.

TELCO FAULT

(or CHECK 94)

The telephone line has a problem.

CALL FOR SERVICE.

If there is no keypad display at all, and the READY indicator

is not lit, operating power (from AC and back-up battery) for the

system has stopped and the system is inoperative. CALL FOR

SERVICE.

Total Power Failure

In The Event Of Telephone Operational Problems

In the event of telephone operational problems, disconnect the control from the phone line by

removing the plug from the phone wall jack. We recommend that your installer demonstrate this

disconnection on installation of the system. Do not attempt to disconnect the phone connection

inside the control. Doing so will result in the loss of your phone lines. If the regular phones work

correctly after the control has been disconnected from the phone wall jack, the control has a

problem and you should immediately call for service. If upon disconnection of the control, there is

still a problem on the phone line, notify the Telephone Company that they have a problem and

request prompt phone repair service. The user may not under any circumstances attempt any

service or repairs to the security system. Repairs must be made only by authorized service (see

the LIMITED WARRANTY statement for information on how to obtain service).

– 39 –

Download from Www.Somanuals.com. All Manuals Search And Download.

0DLQWDLQLQJꢀ<RXUꢀ6\VWHP

The components of your security system are designed to be as

maintenance-free as possible. However, to make sure that your system

is in reliable working condition, do the following:

1. Test your system weekly.

Taking Care of

Your System

2. Test your system after any alarm occurs.

Silencing Low

You can silence the keypad’s warning tones by pressing the OFF key,

Battery Warning but the keypad's low battery message display will remain on as a

reminder that you have a low battery condition in one or more of your

wireless sensors. When you replace the weak battery with a fresh one,

the sensor sends a "good battery" signal to the control as soon as the

sensor is activated (opening/closing of door, window, etc.), causing the

low battery display to turn off. If the sensor is not activated, the display

will automatically clear within approximately 1 hour.

Tones at the

Keypad

Each wireless sensor in your system has a 9-volt or 3-volt battery. The

system detects a low battery in wireless sensors, including smoke

detectors, the personal emergency transmitter, and the portable

wireless keypad and displays a low battery message*. (A low battery in

a portable wireless keypad is detected as soon as one of its keys is

pressed, and displayed as 00.). Battery-operated smoke detectors with

a low battery also emit a single "chirp" sound approximately once

every 20–30 seconds.

Replacing

Batteries in

Wireless Sensors

Wireless sensors

may not have

been used in your

security system

Alkaline batteries provide a minimum of 1 year of operation, and in

most units and applications, provide 2–4 years of service. 3-volt lithium

batteries provide up to 4 or more years of operation. Actual battery life

will depend on the environment in which the sensor is used, the

number of signals that the transmitter in the sensor has had to send,

and the specific type of sensor. Factors such as humidity, high or low

temperatures or large swings in temperature, may all lead to the

reduction of actual battery life in an installation.

IMPORTANT:

Use only batteries

recommended by

your installer as

replacement.

* The low battery message comes on as a warning that battery replacement

in indicated sensor(s) is due within 30 days. In the meantime, a sensor

causing a low battery indication is still fully operational.

• Treat the components of your security system as you would any other

electrical equipment. Do not slam sensor-protected doors or windows.

• Keep dust from accumulating on the keypad and all protective

sensors, particularly on motion sensors and smoke detectors.

• The keypad and sensors should be cleaned carefully with a dry soft

cloth. Do not spray water or any other fluid on the units.

Routine Care

– 40 –

Download from Www.Somanuals.com. All Manuals Search And Download.

)LUHꢀ$ODUPꢀ6\VWHPꢀꢁ,Iꢀ,QVWDOOHGꢂ

THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS

Your fire alarm system (if installed) is on 24 hours a day, for

continuous protection. In the event of an emergency, the strategically

located smoke and heat detectors will sound their alarms and

automatically send signals to your system, triggering a loud,

interrupted pulsed sound* from the Keypad(s) and any external

sounders. A FIRE message will appear at your Keypad and remain on

until you silence the alarm (see below for silencing fire alarms).

General

* Temporal pulse sounding is produced for Fire alarms, as follows:

3 pulses–pause–3 pulses–pause–3 pulses–pause. . . , repeated.

TYPICAL FIRE EMERGENCY DISPLAYS

* - 6 ) ꢆ ꢁ ꢅ ꢆ ꢆ ꢆ 1 % 7 8 ) 6

ꢀꢁ

ALARM

FIRE

& ) ( 6 3 3 1

ALPHA DISPLAY KEYPAD

FIXED-WORD KEYPAD

1. You can silence the alarm at any time by pressing the OFF key (the

security code is not needed to silence fire alarms). To clear the

display, enter your code and press the OFF key again (to clear

Memory of Alarm).

Silencing

Fire Alarms and

Clearing Memory

of Alarm

2. If the Keypad's FIRE display does not clear after the second OFF

sequence, smoke detectors may still be responding to smoke or heat

producing objects in their vicinity. Investigate, and should this be

the case, eliminate the source of heat or smoke.

3. If this does not remedy the problem, there may still be smoke in the

detector. Clear it by fanning the detector for about 30 seconds.

When the problem has been corrected, clear the display by

entering your code and pressing the OFF key.

Depending on the type of smoke detectors in your system, it may be

necessary to "reset" the smoke detectors after a fire alarm has been

turned off. Check with your installer. This "reset" is accomplished at a

keypad, as follows:

Smoke Detector

Reset

Enter User Code*, then press the [1] key (* except “arm only” user).

– 41 –

Download from Www.Somanuals.com. All Manuals Search And Download.

)LUHꢀ$ODUPꢀ6\VWHPꢀꢁ&RQWLQXHGꢂ

THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS

1. Should you become aware of a fire emergency before your smoke or

heat detectors sense the problem, go to your nearest keypad and

manually initiate an alarm by pressing the panic key assigned for

FIRE emergency for 2 seconds. If a key pair has been assigned for

fire, press both keys at the same time. See the Using the Panic Keys

section below for further details.

Manually

Initiating

a Fire Alarm

2. Evacuate all occupants from the premises.

3. If flames and/or smoke are present, leave the premises and notify

your local Fire Department immediately.

4. If no flames or smoke are apparent, investigate the cause of the

alarm. The zone number(s) of the zone(s) in an alarm condition will

be displayed at the keypad.

A key or key pair may have been assigned for manually initiating a

FIRE alarm. See the Panic Keys section for key assignments.

For convenience, indicate the key or key pair assigned for fire below.

Individual Keys

Using the Panic

Key(s) Assigned

for FIRE

Emergency

Press the individual key assigned for fire for 2

seconds.

Key Pairs

1 ^{O FF}

^and∗ READY

∗

READY and

Press the key pair assigned

for fire at the same time.

3 ^{ST AY}

and

DISPLAYS FOLLOWING MANUAL INITIATION OF A FIRE ALARM

* - 6 ) ꢆ ꢇ ꢈ

ꢂꢃ

ALARM

FIRE

ALPHA DISPLAY KEYPAD

FIXED-WORD KEYPAD

– 42 –

Download from Www.Somanuals.com. All Manuals Search And Download.

)LUHꢀ$ODUPꢀ6\VWHPꢀꢁ&RQWLQXHGꢂ

THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS

1DWLRQDOꢀ)LUHꢀ3URWHꢁWLRQꢀ$VVRꢁLDWLRQ

5HꢁRPPHQGDWLRQVꢀRQꢀ6PRNHꢀ'HWHꢁWRUV

With regard to the number and placement of smoke/heat detectors, we

subscribe to the recommendations contained in the National Fire Protection

Association's National Fire Alarm Code (NFPA 72) noted below.

Early warning fire detection is best achieved by the installation of fire

detection equipment in all rooms and areas of the household as follows: A

smoke detector installed outside of each separate sleeping area, in the

immediate vicinity of the bedrooms and on each additional story of the

family living unit, including basements and excluding crawl spaces and

unfinished attics.

In addition, the NFPA recommends that you install heat or smoke detectors

in the living room, dining room, bedroom(s), kitchen, hallway(s), attic,

furnace room, utility and storage rooms, basements and attached garages.

✪

ꢀ

✪

KITCHEN

ꢀ

✪

KITCHEN

BDRM

DINING

BEDROOM

TV ROOM

DINING

ꢁ

BDRM

LIVING ROOM

ꢁ

✪

ꢁ

✪

BEDROOM

LIVING ROOM

✪

ꢀ

ꢁ

Smoke Detectors for Minimum Protection

Smoke Detectors for Additional Protection

Heat-Activated Detectors

ꢁ

✪

ꢀ

BEDROOM

ꢁ

✪

BEDROOM

ꢀ

ꢁ

ꢀ

KTCHN

GARAGE

CLOSED

DOOR

LVNG RM

ꢁ

BASEMENT

– 43 –

Download from Www.Somanuals.com. All Manuals Search And Download.

)LUHꢀ$ODUPꢀ6\VWHPꢀꢁ&RQWLQXHGꢂ

THIS SECTION APPLIES ONLY TO RESIDENTIAL SYSTEMS

(PHUJHQꢁ\ꢀ(YDꢁXDWLRQ

Establish and regularly practice a plan of escape in the

event of fire. The following steps are recommended by

the National Fire Protection Association:

OOM

CLOSET

BEDR

1. Position your detector or your interior and/or

exterior sounders so that they can be heard by all

OOM

BEDR

occupants.

BEDR

2. Determine two means of escape from each room.

One path of escape should lead to the door that

permits normal exit from the building. The other

may be a window, should your path be impassable.

Station an escape ladder at such windows if there

is a long drop to the ground.

FLOOR

OOM

KITCHEN

BEDR

BACK DOOR

OOM

3. Sketch a floor plan of the building. Show windows,

doors, stairs and rooftops that can be used to

escape. Indicate escape routes for each room. Keep

these routes free from obstruction and post copies

of the escape routes in every room.

BEDR

1^STFLOOR

•

4. Assure that all bedroom doors are shut while you

are asleep. This will prevent deadly smoke from

entering while you escape.

•

5. Try the door. If the door is hot, check your

alternate escape route. If the door is cool, open it

cautiously. Be prepared to slam the door if smoke

or heat rushes in.

BACK

6. When smoke is present, crawl on the ground. Do

not walk upright, since smoke rises and may

overcome you. Clearer air is near the floor.

•

7. Escape quickly; don't panic.

FRONT

8. Establish a common meeting place outdoors, away

from your house, where everyone can meet and

then take steps to contact the authorities and

account for those missing. Choose someone to

assure that nobody returns to the house — many

die going back

– 44 –

Download from Www.Somanuals.com. All Manuals Search And Download.

4XLꢃNꢀ*XLGHꢀWRꢀ%DVLꢃꢀ6\VWHPꢀ)XQꢃWLRQV

PROCEDURE

FUNCTION

COMMENTS

Check Zones

Press READY key.

View faulted zones when system not

ready.

Arm System

Enter code. Press arming key desired:

Arms system in mode selected.

(AWAY, STAY, NIGHT-STAY,

MAXIMUM, INSTANT)

Quick Arm

(if programmed)

Press #. Press arming key desired:

(AWAY, STAY, MAXIMUM, INSTANT)

Arms system in mode selected, quickly

and without use of a code.

Bypass Zone(s)

Enter code. Press BYPASS key.

Enter zone number(s) to be bypassed

(use 2-digit entries).

Bypassed zones are unprotected and

will not cause an alarm if violated.

Quick Bypass

(if programmed)

Enter code. Press BYPASS key + [#].

Bypasses all faulted zones

automatically.

Silence Sounders

Burglary:

Enter code. Press OFF key.

Also disarms system. Memory of alarm

remains until cleared.

Fire:

Press OFF key.

Press any key.

Memory of Alarm remains until cleared.

Determine cause.

"Check":

Disarm System

Enter code. Press OFF key.

Also silences sounders. Memory of

alarm remains until cleared.

Clear Alarm

Memory

After disarming, enter code again.

Press OFF key again.

Keypad beeps rapidly on entry if alarm

has occurred while absent. Alarm

display will remain upon disarming

until cleared.

Duress (if active

and connected to

Central Station)

Arm or disarm "normally", but

use your 4-digit Duress code to do so.

Performs desired action and sends

silent alarm to Central Station.

Panic Alarms

Press key [A], [B], or [C] for at least 2

See the Panic Keys section for

(as programmed)

seconds or press and hold designated key emergency functions programmed for

pairs: [1]+[∗], or [∗] + [#], or [3] + [#].

your system. Note: Keys “A”, “B”, and

“C” may have been programmed for

other functions.

Chime Mode

Test Mode

To turn ON or OFF: Enter code. Press

CHIME key.

The keypad will sound if doors or

windows are violated while system is

disarmed and chime mode is ON.

To turn ON: Enter code. Press TEST key. Tests alarm sounder and allows sensors

to be tested.

To turn OFF: Enter code. Press OFF key.

Phone Access

if applicable

Consult Phone Access User's Guide that

accompanies the Phone Module.

Permits system access remotely, via

Touch-tone phone.

– 45 –

Download from Www.Somanuals.com. All Manuals Search And Download.

6XPPDU\ꢀRIꢀ$XGLEOHꢄ9LVXDOꢀ1RWLILꢃDWLRQV

)L[HGꢁ:RUGꢀ'LVSOD\ꢀ.H\SDGV

SOUND

CAUSE

DISPLAY

LOUD,

INTERRUPTED

Keypad & Ext.

FIRE ALARM

FIRE is displayed; zone number of zone in

alarm is displayed. If a fire alarm is manually

activated, zone number 95 will be displayed.

LOUD,

CONTINUOUS

Keypad & Ext.

BURGLARY/AUDIBLE

EMERGENCY ALARM

ALARM is displayed. Zone number of zone in

alarm is also displayed.

ONE SHORT BEEP a. SYSTEM DISARM

a. READY indicator light comes on.

(not repeated)

Keypad only

b. SYSTEM ARMING ATTEMPT

WITH AN OPEN ZONE.

b. Number of the open protection zone displayed.

c. Zone numbers of the bypassed protection

zones are displayed (one beep is heard for

each zone displayed). Subsequently, BYPASS

is displayed.

c. BYPASS VERIFY

ONE SHORT BEEP a. SYSTEM IS IN TEST MODE

a. Opened zone numbers will appear.

(once every 40 secs)

Keypad only

b. LOW BATTERY AT A

TRANSMITTER

b. BAT displayed with zone number of

transmitter.

TWO SHORT BEEPS ARM AWAY or MAXIMUM

Keypad only

AWAY is displayed. Red ARMED indicator is lit.

THREE SHORT

BEEPS

a. ARM STAY, NIGHT-STAY, OR a. STAY or INSTANT is displayed. Red

INSTANT

ARMED indicator is lit.

Keypad only

b. CHIME displayed; zone number of open

protection zone will be displayed if the [✱]

key is pressed.

b. ZONE OPENED WITH

SYSTEM IN CHIME MODE.

RAPID BEEPING

Keypad only

a. TROUBLE

a. CHECK displayed. Zone number of troubled

protection zone is displayed.

b. MEMORY OF ALARM

b. FIRE or ALARM is displayed; zone number

of zone in alarm is displayed

c. BAT displayed with no zone ID number.

c. SYSTEM LOW BATTERY

d. EXT. SOUNDER WIRING FAIL d. CHECK 70 is displayed.

SLOW BEEPING

Keypad only

a. AWAY is displayed.

a. EXIT DELAY WARNING

b. ENTRY DELAY WARNING

b. Exceeding the entry delay time without

disarming causes alarm.

If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring.

– 46 –

Download from Www.Somanuals.com. All Manuals Search And Download.

6XPPDU\ꢀRIꢀ$XGLEOHꢃ9LVXDOꢀ1RWLILꢄDWLRQV

$OSKDꢀ'LVSOD\ꢀ.H\SDGV

SOUND

CAUSE

DISPLAY

LOUD,

INTERRUPTED*

Keypad & Ext.

FIRE ALARM.

FIRE is displayed; descriptor of zone in alarm is

displayed. If a fire alarm is manually activated, zone

number 95 will be displayed.

LOUD,

CONTINUOUS*

Keypad & Ext.

BURGLARY/AUDIBLE

EMERGENCY ALARM.

ALARM is displayed. If programmed, descriptor of

zone in alarm is also displayed

ONE SHORT BEEP a. SYSTEM DISARM.

(not repeated)

a. DISARMED/READY TO ARM is displayed.

b. Number and descriptor of open protection zone is

displayed.

b. SYSTEM ARMING ATTEMPT

Keypad only

WITH AN OPENZONE.

c. Numbers and descriptors of the bypassed zones

are displayed (One beep is heard for each

c. BYPASS VERIFY.

zone displayed). Subsequently, the following is

displayed: DISARMED BYPASS /Ready to Arm.

ONE SHORT BEEP a. SYSTEM IS IN TEST MODE. a. Opened Zone identifications will appear.

(once every 40 secs)

Keypad only

b, LOW BATTERY AT A

TRANSMITTER.

b. LO BAT displayed with description of transmitter.

TWO SHORT BEEPS ARM AWAY or MAXIMUM.

Keypad only

ARMED AWAY or MAXIMUM displayed. Red

ARMED indicator lit.

THREE SHORT

BEEPS

a. ARM STAY, NIGHT-STAY,

OR INSTANT.

a. ARMED STAY or ARMED INSTANT displayed.

Red ARMED indicator lit.

Keypad only

b. CHIME displayed, descriptor of open protection

zone will be displayed if the [✱] key is pressed.

b. ZONE OPENED WHILE

SYSTEM IS DISARMED.

RAPID BEEPING

Keypad only

a. TROUBLE.

a. CHECK displayed. Descriptor of troubled

protection zone is displayed.

b. MEMORY OF ALARM.

b. FIRE or ALARM is displayed; descriptor of zone

in alarm is displayed.

c. SYSTEM LO BAT displayed.

c. SYSTEM LOW BATTERY.

d. EXT. SOUNDER WIRE FAIL.

d. BELL FAILURE is displayed.

SLOW BEEPING

Keypad only

a. EXIT DELAY WARNING

(if programmed).

a. ARMED AWAY OR MAXIMUM is displayed

along with You May Exit Now.

b. DISARM SYSTEM OR ALARM WILL OCCUR

is displayed. Exceeding the delay time without

disarming causes an alarm.

b. ENTRY DELAY WARNING.

* If a bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady

ring.

– 47 –

Download from Www.Somanuals.com. All Manuals Search And Download.

5HJXODWRU\ꢀ6WDWHPHQWVꢀDQGꢀ:DUQLQJV

NOTE: This is a “Grade A” Residential System

RADIO FREQUENCY EMISSIONS

Federal Communications Commission (FCC) Part 15

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet Appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

TELEPHONE/MODEM INTERFACE

FCC Part 68

This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains the FCC registration

number and Ringer Equivalence Number (REN). You must provide this information to the telephone company when requested.

This equipment uses the following USOC jack: RJ31X

This equipment may not be used on telephone-company-provided coin service. Connection to party lines is subject to state tariffs. This

equipment is hearing-aid compatible.

Industry Canada

NOTICE: The Industry Canada Label identifies certified equipment. This certification means that the equipment meets telecommunications

network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements

document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications

company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with

the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user

to this equipment, or equipment malfunctions, may give the telecommunications company to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic

water pipe system, if present, are connected together, This precaution may be particularly important in rural areas.

CAUTION: Users should not attempt to make such connections themselves but should contact appropriate electric inspection authority, or

electrician, as appropriate.

Ringer Equivalence Number Notice:

The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed

to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the

requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

Industrie Canada

AVIS: l’étiquette d’Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme aux normes de

protection, d’exploitation et de sécurité des réseaux de télécommunications, comme le prescrivent les documents concernant les exigences

techniques relatives au matériel terminal. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur.

Avant d’installer ce matériel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installations de l’enterprise locale de

télécommunication. Le matériel doit également être installé en suivant une méthode acceptée da raccordement. L’abonné ne doit pas oublier qu’il

est possible que la conformité aux conditions énoncées ci-dessus n’empêche pas la dégradation du service dans certaines situations.

Les réparations de matériel nomologué doivent être coordonnées par un représentant désigné par le fournisseur. L’entreprise de

télécommunications peut demander à l’utilisateur da débrancher un appareil à la suite de réparations ou de modifications effectuées par

l’utilisateur ou à cause de mauvais fonctionnement.

Pour sa propre protection, l’utilisateur doit s’assurer que tous les fils de mise à la terre de la source d’energie électrique, de lignes téléphoniques

et des canalisations d’eau métalliques, s’il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions

rurales.

Avertissement : L’utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir racours à un service d’inspection des

installations électriques, ou à un électricien, selon le cas.

AVIS : L’indice d’équivalence de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui

peuvent être raccordés à une interface. La terminaison d’une interface téléphonique peut consister en une combinaison de quelques dispositifs, à

la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.

– 48 –

Download from Www.Somanuals.com. All Manuals Search And Download.

&KDUWVꢀRIꢀ<RXUꢀ6\VWHP·Vꢀ)HDWXUHV

SERVICING INFORMATION

Your local authorized service representative is the person best qualified to service your

alarm system. Arranging some kind of regular service program with him is advisable.

Your local service representative is:

Name:

Address:

Phone:

General Features

Features

Comments

Exit Delay

Entry Delay 1

Entry Delay 2

Night-Stay Zones

Quick Arm

Zones:

yes

Quick Bypass

yes

Automatic Paging

Keyswitch Arming

(circle type of LED lighting)

yes

users:

flash

Arm AWAY: steady

Arm STAY: steady

Function Keys

Comments

• Single-Button Arming

• Step Arming

• Paging (see Paging chart)

• Time/Date Display

• Macro Key

† †

• Emergency Key : Personal

† †

• Emergency Key : Silent Alarm

† †

• Emergency Key : Audible Alarm

† †

• Emergency Key : Fire

• Device Activation

Device:

† †Emergency Keys:

A = [1] / [∗]

B = [∗] / [#]

C = [3] / [#]

– 49 –

Download from Www.Somanuals.com. All Manuals Search And Download.

&KDUWVꢀRIꢀ<RXUꢀ6\VWHP·Vꢀ)HDWXUHV

User Setup

The following chart will help keep track of system users. To program a user attribute:

Enter system master code + [8] + user no. + “#” command listed in column heading…

User

No.

User

Name

Security

Auth.

Level

Access

Group

RF Zone

Number

Pager

on/off

Code

enter new code

[#] [1] + level [#] [2] + group [#] [4] + zone no. [#] [5] + 0/1

installer

system master

installer

master

(0)

(1)

(0)

Authority Levels: 0 = standard user

1 = arm only

Paging: 0 = no paging

1 = allow paging

2 = guest

3 = duress

Paging Setup

Pager Phone Number\

Prefix Characters

Pager

Automatically Reports Upon…

open/close alarm/trouble zone list

Sched. Func. Key

Schedules: master code + [#] + [6] [4].

No.

Event

Device No.

Group No. Start

for “02” events: Time/ Day

Stop

Time/ Day

Repeat Random

(see list below) for “01” events:

(0-4)

(yes/no)

(see device list below) enter 1-8

Events:

00 = clear event

01 = device on/off

02 = user access

03 = latch key report

04 = forced STAY arm

05 = forced AWAY arm

06 = auto disarm

07 = display “reminder”

Repeat Options: 0 = none; 1 = repeat weekly; 2 = repeat every other week; 3 = repeat every third week; 4 = repeat every fourth week

List of Output Devices

Device

Description

Schedule No.

Function Key

– 50 –

Download from Www.Somanuals.com. All Manuals Search And Download.

²ꢀ1RWHVꢀ²

– 51 –

Download from Www.Somanuals.com. All Manuals Search And Download.

²ꢀ1RWHVꢀ²

– 52 –

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S INSURANCE PREMIUM CREDIT REQUEST

This form should be completed and forwarded to your homeowner’s insurance carrier for possible

premium credit.

A. GENERAL INFORMATION:

Insured’s Name and Address:

Insurance Company:

Policy No.:

Other ______________________________

FA130CP

Type of Alarm:

Burglary

Fire

Both

Installed by:

Serviced by:

Name

Address

B. NOTIFIES (Insert B = Burglary, F = Fire)

Local Sounding Device

Police Dept.

Fire Dept.

Central Station

Name:

Address:

Phone:

C. POWERED BY: A.C. With Rechargeable Power Supply

D. TESTING:

Quarterly Monthly Weekly

Other

continued on other side

– 53 –

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S INSURANCE PREMIUM CREDIT REQUEST

(cont.)

E. SMOKE DETECTOR LOCATIONS

Furnace Room

Basement

Kitchen

Bedrooms

Attic

Hall

Living Room

Dining Room

F. BURGLARY DETECTING DEVICE LOCATIONS:

Front Door

Basement Door

All windows

Rear Door

All Exterior Doors

1^stFloor Windows

Interior locations

All Accessible Openings, Including Skylights, Air Conditioners and Vents

G. ADDITIONAL PERTINENT INFORMATION:

Signature:

Date:

– 54 –

Download from Www.Somanuals.com. All Manuals Search And Download.

/,0,7$7,216ꢀ2)ꢀ7+,6ꢀ6<67(0

WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM

While this system is an advanced design security system, it does not offer guaranteed protection against burglary or other

emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a

variety of reasons. For example:

•

Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm

sensor or disconnect an alarm warning device.

•

Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work

without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are

not put in properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason,

however briefly.

•

Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even

if the signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into

the path.

•

A user may not be able to reach a panic or emergency button quickly enough.

While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not

activate or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published

by the Federal Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this

System may not work are as follows. Smoke detectors may have been improperly installed and positioned. Smoke

detectors may not sense fires that start where smoke cannot reach the detectors, such as in chimneys, in walls, or

roofs, or on the other side of closed doors. Smoke detectors also may not sense a fire on another level of a residence or

building. A second floor detector, for example, may not sense a first floor or basement fire. Moreover, smoke detectors

have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not

always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping

gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson.

Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as

anticipated, may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death.

Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their

installation manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple

beams of protection, and intrusion can only be detected in unobstructed areas covered by those beams. They cannot

detect motion or intrusion that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or

windows.

•

Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the

optical system can reduce their detection ability. Passive Infrared Detectors sense changes in temperature; however,

as the ambient temperature of protected area approaches the temperature range of 90° to 105°F, the detection

performance can decrease.

•

Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on

the other side of closed or partly open doors. If warning devices sound on a different level of the residence from the

bedrooms, then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may

not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing

traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers.

Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of

service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.

Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect

themselves from the emergency situation. In the case of a monitored alarm system, authorities may not respond

appropriately.

•

This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed

to last as long as 10 years, the electronic components could fail at any time.

The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance.

This alarm system should be tested weekly to make sure all sensors and transmitters are working properly.

Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for

insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and

continue to insure their lives and property.

We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved

ones to learn about these developments.

– 55 –

Download from Www.Somanuals.com. All Manuals Search And Download.

ONE YEAR LIMITED WARRANTY

Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"), 165 Eileen Way, Syosset, New

York 11791, warrants its First Alert Professional security equipment (the "product") to be free from defects

in materials and workmanship for one year from date of original purchase, under normal use and service.

Seller's obligation is limited to repairing or replacing, at its option, free of charge for parts, labor, or trans-

portation, any product proven to be defective in materials or workmanship under normal use and service.

Seller shall have no obligation under this warranty or otherwise if the product is altered or improperly

repaired or serviced by anyone other than the Seller. In case of defect, contact the security professional who

installed and maintains your security equipment or the Seller for product repair.

This one year Limited Warranty is in lieu of all other express warranties, obligations or liabilities. THERE

ARE NO EXPRESS WARRANTIES, WHICH EXTEND BEYOND THE FACE HEREOF. ANY IMPLIED

WARRANTIES, OBLIGATIONS OR LIABILITIES MADE BY SELLER IN CONNECTION WITH THIS

PRODUCT, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, OR FITNESS FOR

A PARTICULAR PURPOSE OR OTHERWISE, ARE LIMITED IN DURATION TO A PERIOD OF ONE

YEAR FROM THE DATE OF ORIGINAL PURCHASE. ANY ACTION FOR BREACH OF ANY

WARRANTY, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF

MERCHANTABILITY, MUST BE BROUGHT WITHIN 12 MONTHS FROM DATE OF ORIGINAL

PURCHASE. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL

OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR

IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR

DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. Some states do not allow

limitation on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

Seller does not represent that the product may not be compromised or circumvented; that the product will

prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product will in

all cases provide adequate warning or protection. Buyer understands that a properly installed and maintained

alarm may only reduce the risk of a burglary, robbery, fire or other events occurring without providing an

alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or

property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY

PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT

FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR

INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR

OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL

NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE

COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty gives you specific legal

rights, and you may also have other rights which vary from state to state. No increase or alteration, written or

verbal, to this warranty is authorized.

149 Eileen Way Syosset, New York 11791

¬.ꢀꢁꢂꢃꢄꢅꢄl

K0736-1 8/02

Download from Www.Somanuals.com. All Manuals Search And Download.

Cisco Systems Network Router 2600XM User Manual
Craftsman Lawn Mower 91737892 User Manual
Crate Amplifiers Stereo Amplifier TX50DE User Manual
Curtis Clock Radio SRCD633 User Manual
Curtis Convection Oven RMW1172 User Manual
CyberHome Entertainment DVR CH DVR 1500 User Manual
Electro Voice Portable Speaker LR4A User Manual
Fisher Price Riding Toy K6670 User Manual
GE Air Conditioner AET05 User Manual
Global Machinery Company Power Hammer MRHD1500CF User Manual