Press PWR once to
turn on or off the
selected home enter-
tainment component.
Use the transport
keys to control
your VCR, or CD or
DVD player.
4. Aim the Catalyst 48 at the component
and press PWR once. It should turn
off. If it does not respond, repeat steps
2-3, trying each code for your brand
until you find one that works. If it still
does not work, try searching for the
code (see Searching For Your Code).
AUX as 2nd TV key:
SETUP - 9 - 9
- 2 - TV- AUX
SEARCHING FOR YOUR CODE
RE-ASSIGNING DEVICE KEYS
The Catalyst 48 can be set up to control a
second TV or VCR, or any combination of
eight home entertainment components.
TROUBLESHOOTING
PROBLEM: LED does not blink when
you press a key.
If your device does not respond to the
Catalyst 48 after trying all codes listed
for your brand, or if your brand is not
listed at all, try searching for your code.
For example, to search for a code for
your TV:
AUX as 2nd VCR key: SETUP - 9 - 9
- 2 - VCR - AUX
CATALYST™ 48
SOLUTION: Replace the batteries with
two (2) new AA alkaline
batteries.
Press AUX, CBL, VCR,
TV, SAT, CD, AMP, or
TNR once to select a
home entertainment
component to control.
Use these keys for
specific features on
your dedicated
components.
AUX as 2nd CBL key: SETUP - 9 - 9
- 2 - CBL - AUX
For example, to have the Catalyst 48 con-
trol a TV, a Cable Converter, and two
VCRs, you will need to re-assign the
unused AUX key to operate the second
VCR as follows:
UNIVERSAL REMOTE CONTROL
NOTE: If the device does not have a PWR
key, press PLAY.
PROBLEM: LED blinks when you
press a key, but home
AUX as 2nd TNR key: SETUP - 9 - 9
- 2 - TNR - AUX
1. On the Catalyst 48, press TV once.
5. Repeat steps 1 through 4 for each
component you want the Catalyst 48
to control.
2. Press and hold SETUP until the LED
blinks twice, then release SETUP.
entertainment component
does not respond.
Use the keypad (0 ~ 9)
to directly select
channels (for example,
09 or 31).
AUX as 2nd AMP key: SETUP - 9 - 9
- 2 - AMP - AUX
1. On the Catalyst 48, press and hold
SETUP until the LED blinks twice,
then release SETUP.
INSTALLING BATTERIES
1. On the back of the Catalyst 48, push
the tab and lift off the battery cover.
3. Enter 9 - 9 - 1. The LED will
SOLUTION: Make sure the Catalyst 48
is aimed at your home
AUX as 2nd CD key:
SETUP - 9 - 9
- 2 - CD - AUX
blink twice.
2. Enter 9 - 9 - 2. The LED will
entertainment component
and is not farther than
15 feet away.
Press MUTE once to
turn sound off
or on.
4. Aim the remote control at the the
TV and slowly alternate between
pressing PWR and TV. Stop when the
TV turns off.
PROGRAMMING
TV/VCR COMBO CONTROL
Perform the following instructions to
control a TV/VCR Combo:
2. Obtain two (2) fully-charged AA
alkaline batteries. Match the + and –
marks on the batteries to the + and
– marks in the battery case, then
insert the new batteries.
blink twice.
AUX as 2nd SAT key: SETUP - 9 - 9
- 2 - SAT - AUX
3. Press VCR once, then press AUX once.
PROBLEM: Catalyst 48 does not con-
trol home entertainment
Press ENTER once after
entering channel
numbers on some TV
models.
4. The AUX key is now ready to be pro-
grammed for your second VCR. See
Programming Component Control.
AUX back to AUX:
SETUP - 9 - 9
- 2 - AUX - AUX
NOTE: In the search mode, the
components or commands
are not working properly.
1. Turn on the TV/VCR Combo and
insert a video cassette.
Catalyst 48 will send IR codes from its
library to the selected device, starting
with the most popular code first.
3. Press the battery cover back into
place. The tab should click when the
cover is locked.
When a re-assignment is done, the LED
will blink twice to confirm your choice.
At that time, you will need to program the
Catalyst 48 to control the new component
(see Programming Component Control).
To re-assign other device keys, repeat
steps 1 through 4 by substituting the key
sequence from the below chart for the
most popular components:
SOLUTION: Try all listed codes for the
component brands being
set up. Make sure they
Use VOL + (or VOL -)
to raise (or lower) the
sound volume.
NOTE: Please read steps 2-4 completely
before proceeding. We recommend
highlighting or writing down the code
for the brand you wish to program
before moving onto step 2.
5. Press SETUP once to lock in the code.
4. Test the unit by pressing PWR and
any mode key (e.g., AUX, CBL, VCR,
etc.). If the batteries are inserted cor-
rectly, the LED will blink once.
can be operated with an
infrared remote control.
6. To search for the codes of your other
components, repeat steps 1 through
5, but substitute the appropriate key
(i.e., AUX, CBL, VCR, SAT, CD, AMP, or
TNR) for the (Auxiliary,VCR, Cable,
Satellite, CD, Amplifier, or Tuner)
component you are searching for.
To Re-Assign Key
Sequence
Use CH + (or CH -) to
select the next higher
(or lower) channel.
Perform
PROBLEM: TV/VCR combo does not
respond properly.
2. On the Catalyst 48, press VCR. Press
and hold SETUP until the LED blinks
twice, then release SETUP.
CHANGING VOLUME LOCK
NOTE: When batteries need replacement,
the Catalyst 48 will blink twice with every
key press. Simply replace them and the
remote control will be restored to its full
functionality, including favorite settings.
TV as 2nd VCR key:
SETUP - 9 - 9
- 2 - VCR - TV
The Catalyst 48 is set to control volume
of a component through your TV while
in the TV,VCR, Cable, or Satellite mode.
However, in an Audio mode (i.e., TNR,
AMP, or CD), you have separate control of
your audio component’s volume.
SOLUTION: Use the VCR codes for
your brand. Some combo
units may require both a
TV code and a VCR code
for full operation.
TV as 2nd CBL key:
TV as 2nd AUX key:
TV as 2nd TNR key:
TV as 2nd AMP key:
TV as 2nd CD key:
TV as 2nd SAT key:
TV back to TV:
SETUP - 9 - 9
- 2 - CBL - TV
Press LAST once to
recall the last channel
and to page back one
screen in the
3. Use the Setup Codes For TV/VCR
Combos (on the back side) to locate
the brand name and then enter the
first four-digit code for your compo-
nent. If performed correctly, the LED
will blink twice.
USER GUIDE
SETUP - 9 - 9
- 2 - AUX - TV
CHECKING THE CODES
PROGRAMMING
COMPONENT CONTROL
The Catalyst 48 can control up to eight
different components. Perform the fol-
lowing instructions for each component
you want controlled:
main menu.
PROBLEM: No volume on a 2nd TV.
If you have set up the Catalyst 48 using
the Searching For Your Code procedure,
you may need to find out which four-
digit code is operating your equipment:
If your TV is not remote controllable, or
if you want volume to be controlled by a
different component, you can change the
Volume Lock setting to control a volume
through a non-associated mode (e.g.,
through the cable in the TV mode).
SETUP - 9 - 9
- 2 - TNR - TV
Press SLEEP to activate
your TV’s sleep timer.
Or if none is available,
press SLEEP to activate
the Catalyst 48’s sleep
timer for automatic
shut-off of your TV.
Each key press (up to
four) add 15 minutes
to the sleep timer.
SOLUTION: Follow instructions in
INTRODUCTION
The Catalyst™ 48 Universal Remote
Control, developed by Universal
Electronics, Inc. for Funai, is the complete
solution for all of your remote control
requirements. It is designed to operate
from four to eight devices with the
emphasis on features and functions of
your dedicated component(s).
NOTE: If the LED did not blink twice, then
repeat steps 2 through 3 and try entering
the same code again.
Changing Volume Lock.
SETUP - 9 - 9
- 2 - AMP - TV
PROBLEM: CH+ , CH , and LAST do
-
For example, to find out which code is
operating your TV:
not work for your RCA TV.
4. Aim the Catalyst 48 at the component
and press PWR once. It should turn
off. If it does not respond, repeat steps
2-3, trying each code for your brand
until you find one that works. If it still
does not work, try searching for the
code (see Searching For Your Code).
SOLUTION: Due to RCA design (1983-
1987), only the original
SETUP - 9 - 9
- 2 - CD - TV
NOTE: For TV/VCR Combo control, see the
next section.
1. On the Catalyst 48, press TV once.
To change Volume Lock to the
another mode:
remote control will oper-
ate these functions.
2. Press and hold SETUP until the LED
blinks twice, then release SETUP.
1. Turn on a component (e.g.,VCR)
and, if applicable, insert media,
(e.g., cassette or disc).
SETUP - 9 - 9
- 2 - SAT - TV
1. On the Catalyst 48, press and hold
SETUP until the LED blinks twice,
then release SETUP.
PROBLEM: Changing channels does
not work properly.
3. Enter 9 - 9 - 0. The LED will
Press INPUT once to
switch the input of the
chosen component.
SETUP - 9 - 9
- 2 - TV - TV
blink twice.
The Catalyst 48 requires two (2) fresh
AA alkaline batteries (not included)
and some easy programming to control
your devices. For best results, please
read and perform all instructions listed
here. Also, keep these instructions for
future reference.
NOTE: Please read steps 2-4 completely
before proceeding. We recommend
highlighting or writing down the codes
and device you wish to program before
moving onto step 2.
NOTE: If the device does not have a PWR
key, press PLAY.
SOLUTION: If original remote control
required pressing ENTER
to change channels, press
ENTER on the Catalyst 48
after entering the
2. Enter 9 - 9 - 3 and then press any
mode key once (except TV). The LED
will blink twice.
4. To view the code for the first digit,
press 1 once.Wait 3 seconds, count
the LED blinks (e.g., 3 blinks = 3)
and write down the number.
VCR as 2nd TV key:
SETUP - 9 - 9
- 2 - TV - VCR
Use GUIDE to display
the program guide.
5. If you’ve located a setup code that
works, but it has a separate TV code,
you’ll also need to program it into the
Catalyst 48 to access volume control
as follows:
3. Now, whenever you press VOL +,
VOL –, or MUTE, volume will be con-
trolled by your mode choice.
VCR as 2nd CBL key: SETUP - 9 - 9
- 2 - CBL - VCR
Use EXIT to exit out of
the selected compo-
nent’s menu or guide.
2. On the Catalyst 48, press a component
key once (i.e., AUX, CBL, VCR, TV, SAT,
CD, AMP, or TNR). Press and hold
SETUP until the LED blinks twice,
then release SETUP.
NOTE: If a code digit is “0”, the LED
will not blink.
channel number.
PROBLEM: Tried “Search Method”
and still could not find a
working code.
VCR as 2nd AUX key: SETUP - 9 - 9
- 2 - AUX - VCR
5. Repeat step 4 three more times for
remaining digits. Use 2 for the sec-
ond digit, 3 for the third digit, and 4
for the fourth digit.
To change Volume Lock back to the
TV mode:
a. Press TV once. The LED will
Use the cursor keys to
move the cursor in
the program guide and
menu screens.
FEATURES AND FUNCTIONS
Use the Key Charts to learn how the
blink twice.
VCR as 2nd TNR key: SETUP - 9 - 9
- 2 - TNR - VCR
b. Enter the TV code for your
TV/VCR Combo. If correct, the
LED will blink twice.
SOLUTION: Try the “Search Method”
again after clearing out
the device key as follows:
Press and hold SETUP
1. On the Catalyst 48, press and hold
SETUP until the LED blinks twice,
then release SETUP.
3. Use the Manufacturer’s Codes (on the
back side) to locate the the type of
component and brand name and
then enter the first four-digit code
for your component. If performed
correctly, the LED will blink twice.
Catalyst 48 functions.
6. To check for the codes of your other
components, repeat steps 1 through
5, but substitute the appropriate key
(i.e., AUX, CBL, VCR, SAT, CD, AMP, or
TNR) component you are checking.
As before, write down each four-
digit code.
VCR as 2nd AMP key: SETUP - 9 - 9
- 2 - AMP - VCR
Key Charts
Use SELECT to choose
options from your
selected component’s
menu or guide.
If there is no separate TV code listed,
you will need to perform the follow-
ing steps to access volume control:
2. Enter 9 - 9 - 3 and then press TV.
The LED (red light)
blinks to show that
the remote control is
working and is
until the red light blinks
twice, then release. Next
enter 9 - 9 - 2. Then press
and release the device key
to be cleared twice.
The LED will blink twice.
VCR as 2nd CD key:
SETUP - 9 - 9
- 2 - CD - VCR
3. Now, whenever you press VOL +,
VOL –, or MUTE on the Catalyst 48,
volume will be controlled by your TV.
NOTE: If the LED did not blink twice, then
repeat steps 2 through 3 and try entering
the same code again.
Use INFO to display
current channel and
program information.
a. Press and hold SETUP until the
LED blinks twice, then release
SETUP.
VCR as 2nd SAT key: SETUP - 9 - 9
- 2 - SAT - VCR
sending signals.
Use SETUP for all
programming
sequences.
Continued on back...
VCR back to VCR:
SETUP - 9 - 9
- 2 - VCR - VCR
Press MENU to access
the menu of your
b. Enter 9 - 9 - 3 . The LED will
blink twice.
chosen component.
c. Press VCR once. The LED will
blink twice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|