Extron electronic Tablet Accessory 68 1407 01 User Manual

User’s Manual  
RGB-DVI 300 and RGB-HDMI 300  
Video Scalers  
68-1407-01  
Rev. A  
03 09  
Download from Www.Somanuals.com. All Manuals Search And Download.  
警告  
安全须知 中文  
这个符号提示用户该设备用户手册中  
电源 设备只能使用产品上标明的电源。 设备  
必须使用有地线的供电系统供电。 第三条线  
(地线)是安全设施,不能不用或跳过。  
有重要的操作和维护说明。  
拔掉电源 为安全地从设备拔掉电源,请拔掉所有设备后  
或桌面电源的电源线,或任何接到市电系统的电源线。  
这个符号警告用户该设备机壳内有暴  
露的危险电压,有触电危险。  
电源线保护 妥善布线, 避免被踩踏,或重物挤压。  
维护 所有维修必须由认证的维修人员进行。 设备内部  
没有用户可以更换的零件。为避免出现触电危险不要自  
己试图打开设备盖子维修该设备。  
注意  
阅读说明书 户使用该设备前必须阅读并理  
解所有安全和使用说明。  
通风孔 有些设备机壳上有通风槽或孔,它们是用来防止  
机内敏感元件过热。 不要用任何东西挡住通风孔。  
保存说明书 用户应保存安全说明书以备将来使  
用。  
锂电池 不正确的更换电池会有爆炸的危险。 必须使用  
与厂家推荐的相同或相近型号的电池。 按照生产厂的  
建议处理废弃电池。  
遵守警告 用户应遵守产品和用户指南上的所有安  
全和操作说明。  
避免追加 不要使用该产品厂商没有推荐的工具或  
追加设备,以避免危险。  
声明  
所使用电源为 A 级产品,在生活环境中,该产品可能会造成无线电干扰。在这种情况下,可能需要用  
户对其干扰采取切实可行的措施。  
FCC Class A Notice  
This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this  
device may not cause harmful interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation. The Class A limits are designed to  
provide reasonable protection against harmful interference when the equipment is operated in  
a commercial environment. This equipment generates, uses, and can radiate radio frequency  
energy and, if not installed and used in accordance with the instruction manual, may cause harmful  
interference to radio communications. Operation of this equipment in a residential area is likely to  
cause harmful interference, in which case the user will be required to correct the interference at his  
own expense.  
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used  
with the unit to ensure compliance with FCC emissions limits.  
N
For complete safety information about these products please read the Safety  
Compliances sheet, which available online at www.extron.com.  
N
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Chapter One Introduction.................................................... 1-1  
About this Manual .................................................................... 1-2  
RGB-DVI 300 and RGB-HDMI 300 Description.................. 1-2  
RGB-DVI 300 and RGB-HDMI 300 Features........................ 1-3  
Chapter Two Installation ...................................................... 2-1  
Mounting the Scalers............................................................... 2-2  
Tabletop placement ............................................................... 2-2  
Rack Mounting....................................................................... 2-2  
UL guidelines for rack mounting...........................................2-2  
Rack mounting procedures....................................................2-3  
Under-desk/wall mounting ................................................... 2-4  
Through-desk mounting........................................................ 2-5  
Front Panel Layout.................................................................... 2-6  
Rear Panel Layout...................................................................... 2-7  
Chapter Three Operation...................................................... 3-1  
Input and Output Configuration.......................................... 3-2  
Input signal............................................................................. 3-2  
Output Signal......................................................................... 3-3  
Table of Output Resolutions and Refresh Rates.................. 3-4  
Other....................................................................................... 3-6  
Front Panel Connections and Controls............................... 3-7  
LED indicator.......................................................................... 3-7  
Config port............................................................................. 3-7  
Front panel menu controls.................................................... 3-8  
Front panel security lockout (executive modeꢀ....................3-8  
Main menu..............................................................................3-8  
Auto Image ...........................................................................3-10  
Picture controls.....................................................................3-11  
User presets ..........................................................................3-12  
Input configuration..............................................................3-13  
Output configuration...........................................................3-14  
Advanced configuration ......................................................3-15  
Rear Panel Connections......................................................... 3-18  
Power Connections.............................................................. 3-18  
Input Connections................................................................ 3-19  
Output Connections............................................................. 3-19  
RS-232 Connection............................................................... 3-20  
RGB-DVI 300 and RGB-HDMI 300 • Table of Contents  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents, cont’d  
Chapter Four Controls ............................................................ 4-1  
Introduction to SIS.................................................................. 4-2  
Symbols used in this manual................................................. 4-3  
Error messages....................................................................... 4-5  
Command/response table for SIS commands .................. 4-6  
Signal Processing Products Control Program ................. 4-17  
Installing the SPPCP............................................................. 4-17  
Running the SPPCP............................................................... 4-17  
Firmware Upgrades................................................................. 4-19  
Appendix A Reference Information ............................A-1  
Specifications..............................................................................A-2  
Included Parts .............................................................................A-5  
Accessories...................................................................................A-5  
All trademarks mentioned in this manual are the properties of their respective owners.  
68-1407-01  
Rev. A  
03 09  
RGB-DVI 300 and RGB-HDMI 300 • Table of Contents  
ii  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RGB-DVI 300 and RGB-HDMI 300  
Chapter One  
1
Introduction  
About this Manual  
RGB-DVI 300 and RGB-HDMI 300 Description  
RGB-DVI 300 and RGB-HDMI 300 Features  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
About this Manual  
This manual contains information about the Extron  
RGB-DVI 300 and RGB-HDMI 300 video scalers/converters  
with instructions on how to install, configure, and operate the  
equipment.  
Unless otherwise specified, references in this manual to the  
"video converter" or "video scaler" relate to the features or  
operation of both models.  
RGB-DVI 300 and RGB-HDMI 300 Description  
The RGB-DVI 300 and RGB-HDMI 300 are analog to digital  
video converters with built-in scaling.  
The units accept a single RGB or HDTV component (R-Y, Y, B-Y)  
input video signal at any standard RGB or HDTV component  
resolution, through a female 15-pin HD connector.  
A single video output at any of large range of resolutions  
and/or refresh rates is provided through a DVI-I (RGB-DVI 300)  
or HDMI (RGB-HDMI 300) connector.  
Input and output settings, picture controls, and advanced  
settings can be adjusted through the front panel menu with  
on-screen display, or RS-232, using Extron's Simple Instruction  
Set (SIS) commands.  
Extron  
Extron  
RGB-HDMI 300  
RGB to HDMI Scaler  
MVX 128 VGA A  
VGA & Audio  
Matrix Switcher  
7
RESET  
RS-232  
7
8
A
L
S
Rx  
Tx  
OUTPUT  
2
HDMI OUTPUT  
5
TE  
3R/S42  
RMEO  
3
4
8
7
1
2
6
00  
3
I
M
S
D
H
-
5
B
G
R
OUTPUT  
T
U
P
I
N
B
RG  
4
3
11  
2
POWERX  
12V  
0.5A MA  
1
12  
9
12  
INPUTS  
10  
11  
0
1
8
9
5
6
8
3
4
7
INPUTS  
6
5
4
2
3
T
E
.
D
I
S
L
1
I
3
2
E
2
T
.
S
.
T
U
C
1
Flat Panel Display  
PC  
RGB-DVI 300 and RGB-HDMI 300 • Introduction  
1-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RGB-DVI 300 and RGB-HDMI 300 Features  
Accept all standard RGB and HDTV YUV inputs — through a female  
15-pin HD connector.  
Multiple output resolutions — These units can output an extensive  
range of unique DVI (or HDMI) combinations of resolution/  
refresh rate. Resolutions range from 640x480 to 1920x1200,  
including 1080p, with refresh rates ranging from 23.98 to 75 Hz.  
Auto ImageThis feature automatically optimizes the image to the  
scaled output rate, eliminating complex setup.  
Simple Instruction Set commands — RS-232 ports on the front and  
back panels allow easy configuration by a host device, using  
Extron SIS commands.  
Complete picture control adjustment — Input and output video  
signals can be fully adjusted through the front panel menu or  
through serial SIS commands.  
Front panel menu selection — The front panel buttons can be used to  
navigate and select menu options with the on-screen display.  
Preset values — 16 Input Presets and 3 User Presets make it easy to  
save and recall commonly used input sources.  
Front panel security lockout — This feature locks all front panel  
controls to prevent accidental or unauthorized reconfiguration.  
Easy mounting — The 1" H x 8.75" W x 6" D (2.6 cm H x  
22.2 cm W x 15.2 cm D) size of the units allows a wide range of  
mounting options.  
RGB-DVI 300 and RGB-HDMI 300 • Introduction  
1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction, cont’d  
RGB-DVI 300 and RGB-HDMI 300 • Introduction  
1-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RGB-DVI 300 and RGB-HDMI 300  
Chapter Two  
2
Installation  
Mounting the Scalers  
Front Panel Layout  
Rear Panel Layout  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Mounting the Scalers  
The 1" height and half rack width of the RGB-DVI 300 and  
RGB-HDMI 300 units allow them to be mounted on a tabletop,  
on racks, under furniture, or through furniture.  
Tabletop placement  
Attach the four provided rubber feet to the bottom of the unit  
and place it in any convenient location.  
Rack Mounting  
UL guidelines for rack mounting  
The following Underwriters Laboratories (UL) guidelines are  
relevant to the safe installation of these products in a rack:  
1.  
Elevated operating ambient temperature — If the unit  
is installed in a closed or multi-unit rack assembly, the  
operating ambient temperature of the rack environment  
may be greater than room ambient temperature. Therefore,  
install the equipment in an environment compatible with  
the maximum ambient temperature (Tma: +122 °F, +50 °C)  
specified by Extron.  
2.  
3.  
4.  
Reduced air flow — Install the equipment in the rack  
so that the equipment gets adequate air flow for safe  
operation.  
Mechanical loading — Mount the equipment in the rack  
so that uneven mechanical loading does not create a  
hazardous condition.  
Circuit overloading — Connect the equipment to  
the supply circuit and consider the effect that circuit  
overloading might have on overcurrent protection  
and supply wiring. Appropriate consideration of the  
equipment nameplate ratings should be used when  
addressing this concern.  
5.  
Reliable earthing (grounding) — Maintain reliable  
grounding of rack-mounted equipment. Pay particular  
attention to supply connections other than direct  
connections to the branch circuit (such as the use of power  
strips).  
RGB-DVI 300 and RGB-HDMI 300 • Installation  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rack mounting procedure  
The unit can be mounted on any of these rack systems:  
RSU 129: 9.5" deep, 1U rack shelf kit (part # 60-190-01)  
RSB 129: 9.5" deep, 1U basic rack shelf (part # 60-604-01)  
RSU 126: 6" deep, 1U rack shelf kit (part # 60-190-10)  
RSB 126: 6" deep, 1U basic rack shelf (part # 60-604-10)  
1. Remove rubber feet if these have been installed on the  
bottom of the unit.  
2. Align the holes in the base of the unit with holes in the  
shelf. Secure the unit to the shelf with two 4-40 x 3/16"  
screws in diagonally opposite corners (see the figure  
below).  
3. Install false faceplate(s) or other unit(s) on the rack shelf.  
4. Attach the shelf to the rack with the four provided  
10-32 x 3/4" bolts  
6" Deep Rack Shelf  
1/2 Rack Width Front False  
Faceplate  
Front false  
faceplate  
uses 2  
screws.  
(2) 4-40 x 3/16"  
Screws  
Use 2 mounting holes on  
opposite corners.  
Rack mounting  
RGB-DVI 300 and RGB-HDMI 300 • Installation  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation, cont’d  
Under-desk/wall mounting  
Mount the unit under a desk or podium or to a wall, using  
the optional Extron MBU 125 under-desk mounting kit  
(part # 70-077-01) as follows:  
1.  
2.  
Remove rubber feet if these have been attached.  
Secure the mounting brackets to the scaler, using the four  
4-40 x 3/16" screws provided.  
Because of the position of the mounting holes, the  
units must be mounted upside-down under the desk or  
podium, or with the bottom surface facing the wall.  
N
Under-desk mounting  
3.  
4.  
5.  
Hold the unit, with the brackets attached, against the wall  
or under the table or other furniture. Mark the location of  
the bracket s' screw holes on the mounting surface.  
Drill four pilot holes, each 3/32" (2 mm) in diameter by  
1/4" (6.3 mm) deep in the mounting surface at the marked  
screw locations.  
Insert #8 wood screws into the four pilot holes. Tighten  
each screw into the mounting surface until just less than  
1/4" (6.3 mm) of the screw head protrudes.  
6.  
7.  
Guide the mounting screws through the slots in the  
brackets and place the unit tight against the surface.  
Slide the unit slightly in or out so that the brackets are  
resting on the screws and support the weight of the unit;  
tighten all four screws to secure the unit in place (see the  
figure above).  
RGB-DVI 300 and RGB-HDMI 300 • Installation  
2-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Through-desk mounting  
Mount the unit through a desk or podium using the optional  
Extron MBD 129 through desk mounting kit (part # 70-077-02) as  
follows:  
1.  
2.  
Remove rubber feet if these have been attached.  
Attach the brackets to the scaler, using the four 4-40 screws  
provided; leave the screws slightly loose.  
Through-desk mounting  
3.  
Hold the unit in position, under the mounting surface.  
Mark the location of the four screw holes and the  
mounting hole to be cut in the table.  
4.  
Remove the table material. Test the fit by inserting the  
front of the device through the hole. If necessary, use a  
rasp or coarse file to enlarge the hole.  
5.  
6.  
7.  
8.  
Drill four pilot holes, each 3/32" (2 mm) in diameter by  
1/4" deep (6.3 mm) deep.  
Attach the brackets to the mounting surface, using the four  
#8 wood screws provided with the kit.  
Slide the device in or out until the front panel is flush with  
the table surface. Tighten the screws installed in step 2.  
If these screws are inaccessible to a screwdriver, mark the  
location of the unit relative to the brackets, remove the unit  
and brackets, tighten the screws, and replace the unit.  
RGB-DVI 300 and RGB-HDMI 300 • Installation  
2-5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation, cont’d  
Front Panel Layout  
The illustration below shows the front panel features and  
controls of the RGB-HDMI 300 (upper image) and RGB-DVI 300  
(lower image):  
ADJUST  
CONFIG  
MENU  
ENTER  
RGB - HDMI 300  
1
2
3
4
ADJUST  
CONFIG  
MENU  
ENTER  
RGB - DVI 300  
Front panel layout  
LED indicator — A solid green light indicates the unit is  
receiving power and has an active video input. A solid amber  
light indicates the unit is receiving power but no video input.  
a
Config port — Both models can be configured using the Extron  
Simple Instruction Set (SIS) commands or through the Signal  
Processing Products Control Program (SPPCP). Either type of  
control is provided through this 2.5 mm Tip Ring Sleeve (TRS)  
serial configuration port or the RS-232 captive screw connector  
b
on the rear panel ( ). See chapter 4 for instructions about SIS  
8
commands and the control software.  
Menu and Enter buttons — These buttons are used to navigate  
the menu when configuring the input and output video signals  
(see page 3-8) and to enable and disable the Front Panel Security  
Lockout (Executive mode; see page 3-8).  
c
d
To see menu selections, a display device must be attached  
to the output of the video converter.  
N
Rotary encoders — The horizontal and vertical rotary encoders  
highlight menu items and adjust the value of items that have  
been selected from the menu.  
RGB-DVI 300 and RGB-HDMI 300 • Installation  
2-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rear Panel Layout  
The illustration below shows the rear panel features of the  
RGB-HDMI 300 (upper image) and RGB-DVI 300 (lower image):  
POWER  
12V  
RGB/ R-Y, Y, B-Y INPUT  
1.0A MAX  
RS-232  
Tx Rx  
HDMI OUTPUT  
RGB  
- HDMI 300  
5
6
7
8
POWER  
12V  
DVI-D OUTPUT  
RGB/ R-Y, Y, B-Y INPUT  
1.0A MAX  
RS-232  
Tx Rx  
RGB  
- DVI 300  
Rear panel layout  
Power input — Connect the 12 VDC external power supply  
(provided) to this 3.5 mm, 2-pole captive screw connector.  
e
f
g
RGB input — Connect an analog RGB or HDTV YUV video  
input signal to this female 15-pin HD connector.  
Digital signal output — Both models output digital signals.  
The RGB-DVI 300 outputs a DVI-D signal through a female  
DVI-I connector; the RGB-HDMI 300 outputs an HDMI signal  
through a female HDMI connector.  
RS-232 input — Both models can be configured by using SIS  
commands or through the SPPCP. Either means of control is  
provided through this 3.5 mm, 3-pole captive screw RS-232  
serial port connector or the TRS config port on the front panel  
2
h
(
). See chapter 4 for instructions about SIS commands and  
control software.  
RGB-DVI 300 and RGB-HDMI 300 • Operation  
2-7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation, cont’d  
RGB-DVI 300 and RGB-HDMI 300 • Installation  
2-8  
Download from Www.Somanuals.com. All Manuals Search And Download.