User Guide
XTP Extenders
XTP T HDMI
XTP R HDMI
XTP HDMI Transmitter and Receiver
68-1723-01 Rev. A
07 13
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference; the user must correct the interference at his own expense.
ATTENTION: The Twisted Pair Extension technology works with unshielded twisted
pair (UTP) or shielded twisted pair (STP) cables; but, to ensure FCC Class A and CE
compliance, STP cables and STP connectors are required.
For more information on safety guidelines, regulatory compliances, EMI/EMF
Compliance Guide” on the Extron website.
Copyright
© 2013 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks(®), registered service marks(SM), and trademarks(TM) are the property of
RGB Systems, Inc. or Extron Electronics:
Registered Trademarks(®)
AVTrac, Cable Cubby, CrossPoint, eBUS, EDID Manager, EDID Minder, Extron, Flat Field,GlobalViewer, Hideaway, Inline, IP Intercom,
IP Link, Key Minder, LockIt, MediaLink, PlenumVault, PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch,
System Integrator, TeamWork, TouchLink, V-Lock, VersaTools, VN-Matrix, VoiceLift, WallVault, WindoWall, XTP, XTP Systems
Registered Service Mark (SM) : S3 Service Support Solutions
Trademarks(™)
AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), AIS (Advanced Instruction Set), Auto-Image, CDRS (Class D
Ripple Suppression), DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator, DSVP
(Digital Sync Validation Processing), FastBite, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, ProDSP, QS-FPC (QuickSwitch Front Panel
Controller), Scope-Trigger, SIS, Simple Instruction Set, Skew-Free, SpeedNav, Triple-Action Switching, XTRA, ZipCaddy, ZipClip
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
WARNING:
A warning indicates a situation that has the potential to result in death or
severe injury.
ATTENTION: Attention indicates a situation that may damage or destroy the product or
associated equipment.
NOTE: A note draws attention to important information.
TIP: A tip provides a suggestion to make working with the application easier.
Software Commands
Commands are written in the fonts shown here:
^ARMerge Scene,,Op1 scene 1,1^B51^W^C
[01]R000400300004000080000600[02]35[17][03]
EX!*X1&*X2)*X2#*X2!CE}
NOTE: For commands and examples of computer or device responses mentioned
in this guide, the character “0” is used for the number zero and “O” represents the
capital letter “o.”
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the Filemenu, select New.
Click the OKbutton.
Specifications Availability
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
XTP T HDMI Transmitter and XTP R HDMI Receiver • Contents
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Contents
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
This section contains general information about this guide and the Extron XTP T HDMI
transmitter and XTP R HDMI receiver. Topics in this section include:
•
•
•
About This Guide
This guide contains installation, operation, control, and reference information for the
XTP T HDMI transmitter and the XTP R HDMI receiver.
In this guide, the terms “transmitter,” “XTP T HDMI,” and “XTP HDMI transmitter” are used
interchangeably to refer to the XTP T HDMI transmitter. The terms “receiver,” “XTP R HDMI,”
and “XTP HDMI receiver” are used interchangeably to refer to the XTP R HDMI receiver.
About the XTP HDMI Transmitter and Receiver
Both the XTP T HDMI transmitter and XTP R HDMI receiver send or receive video, audio,
bidirectional RS-232 and IR, and Ethernet over a single twisted pair cable. They are
HDCP-compliant and support 1080p/60 Deep Color and 1920x1200 signals, and
embedded HD lossless audio formats. They work with Extron XTP devices in matrix or
point-to-point applications for signal distribution and long-distance transmission (up to 330
feet) between remote endpoints, using shielded or unshielded CATx cable.
They can be powered locally or remotely through an Extron XTP Power Injector or XTP
matrix switcher.
Both devices can be controlled through Extron Simple Instruction Set (SIS) or the XTP
Configuration Software on page 23).
XTP T HDMI Transmitter and XTP R HDMI Receiver • Introduction
1
Download from Www.Somanuals.com. All Manuals Search And Download.
The following diagram shows some ways the XTP T HDMI and the XTP R HDMI can be
integrated in an XTP matrix application.
Ethernet
Extron
AV Control
Network
TLP 1000TV
10" Tabletop TouchLink
Touchpanel
Ethernet
Extron
IPCP 505
IP Link Control
Processor
House Network Switch
Ethernet
IR
100-240V
50-60Hz
1
2
COM1
COM2
COM3
COM7
1
2
3
4
1
5
2
3
4
eBUS
+
-
+
-
TX RX
TX RX
TX RX
TX RX
TS CTS
S
G
S
G
S
G
S
G
+V
D
-S +S
12W
PWR OUT
=
LA
SWITCHED 12VDC
40W MAX TOTAL
IR/SERIAL
RELAY
6
3
4
COM4
COM5
COM6
COM8
5
6
7
8
7
8
FLEX I/O
TX RX
TX RX
TX RX
TX RX
CTS
S
S
G
+
+
-
1
2
3
4
5A MAX
Ethernet
Ethernet
HDMI
PC
Flat Panel
Display
HDMI
RS-232
IR
Ethernet
INPUTS
HDMI AUDIO
ON
SIG
LINK
POWER
12V
--A MAX
AUDIO
OVER XTP
L
R
RS-232
IR
RESET
SIG
LINK
XTP
R
HDMI
RESET
OUTPUTS
OFF
POWER
12V
--A MAX
ACTLANLINK
RELAYS
HDMI
LOOP-THRU
+
−
+
−
XTP
T
HDMI
T
x
R
x
T
x
R
x
XTP UT
OVER XTP
HDMI AUDIO
ON
AUDIO
S/PDIF
L
R
1
2
RS-232
IR
OFF
T
x
R
x
T
x
R
x
XTP N
ACTLANLINK
HDMI
+
-
+
-
Extron
XTP T HDMI
CAT 5-type Cable
Extron
XTP R HDMI
Long Distance XTP
Long Distance XTP
Receiver for HDMI
Transmitter for HDMI
IN
IN
IN
IN
IN
IN
OUT
OUT
OUT
OUT
OUT
OUT
IN
IN
OUT
REMOTE
RS 232/RS422
Ethernet
HDMI
Ethernet
ACT
LAN
LINK
RESET
INPUTS
POWER
SIG
LINK
RS-232
HDMI
HDMI AUDIO
ON
OVER XTP
AUDIO
12V
Laptop
O
U
T
--A MAX
L
R
R-32
R
I
RESET
N
P
U
T
S
P
U
T
OFF
ACTLANLINK
HDMI
LOOP-THRU
+
−
+
−
XTP
T
HDMI
T
x
R
x
T
x
R
x
XTP UT
S
Extron
XTP T HDMI
Flat Panel
Display
SIG
LINK
XTP
R
HDMI
RESET
OUTPUTS
POWER
12V
--A MAX
OVXTP
HDMI AUDIO
ON
AUDIO
S/PDIF
RELAYS
L
R
1
2
RS-2
IR
OFF
ACTLANLINK
T
x
R
x
T
x
R
x
+
-
+
-
XTP N
HDMI
Long Distance XTP
1
0
0
-
2
4
0
V
-
-
A
M
A
X
Transmitter for HDMI
Ethernet
Extron
50-60Hz
DISCONNECT POWER
CORD BEFORE
SERVICING
XTP R HDMI
Long Distance XTP
Receiver for HDMI
STANDBY/ON
PQLS
HDMI
OPEN/CLOSE
F
L
O
F
F
US
IR
Stereo Audio
Blu-ray
HDMI
INPUTS
HDMI AUDIO
ON
SIG
LINK
POWER
12V
--A MAX
AUDIO
OVER XT
RS-232
L
R
RESET
OFF
ACTLANLINK
HDMI
LOOP-THRU
+
XTP
T
HDMI
x
R
x
x
XTP OUT
Extron
XTP T HDMI
Long Distance XTP
Transmitter for HDMI
Extron
100-240V
1.3A, 50-60Hz
17TT
XPA 1002
WIRING
OUTPUT
C
US AUDIO/VIDEO
APPARATUS
CLASS
REMOTE
2
LISTED
LEVEL
INPTS
1
2
10V
50 mA
VOL/MUTE
1
2
1
2
XTP CrossPoint 3200
Modular Digital
LIMITER/
PROTECT
1
2
SIGNAL
0
0
STANDBY
Extron
XPA 1002
Stereo Power Ampliꢀer
Matrix Switcher
Extron
SI 28
Surface Mount
Speakers
Figure 1. Typical XTP HDMI Transmitter and Receiver Matrix Application
Key Features
Reliable cable infrastructure — Transmits or receives video, audio, bidirectional
RS-232 and IR, and Ethernet up to 330 feet (100 m) over a CATx cable, providing
high reliability and maximum performance on an economical and easily installed cable
infrastructure.
1080p/60 Deep Color and 1920x1200 signals — Supports digital signal transmission up
to 330 feet over a single twisted pair cable, maintaining superior image quality at the highest
resolutions.
CAT 5e, 6, 6a, and 7 compatible — Optimized for use with common unshielded and
shielded twisted pair cable types. XTP systems fully support a maximum transmission
distance of 330 ft (100 m) for all compatible resolutions. Shielded twisted pair cable provides
added protection from outside interference.
Bidirectional RS-232 and IR insertion — Allows a remote display to be controlled without
the need for additional cabling through bidirectional RS-232 and IR control signals inserted
into the XTP output.
HDMI specification features — Include data rates up to 6.75 Gbps, Deep Color up to
12-bit, 3D, and HD lossless audio formats.
HDCP compliance — Ensures display of content-protected media and interoperability with
other HDCP-compliant devices.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Introduction
2
Download from Www.Somanuals.com. All Manuals Search And Download.
EDID Minder — Automatically manages EDID communication between connected devices.
It ensures that all sources power up properly and reliably outputs content for display.
Key Minder — Authenticates and maintains continuous HDCP encryption between input
and output devices to ensure quick and reliable switching in professional AV environments,
while enabling simultaneous distribution of a single source signal to one or more displays.
Ethernet extension — Centralized 10/100 Ethernet communication can be implemented
via an Ethernet pass-through port to reduce the amount of independent network drops
required within a system.
Remote power capability — To simplify integration, XTP transmitters and receivers can be
powered by the XTP CrossPoint matrix switcher or XTP Power Injectors.
Multiple embedded audio formats — Compatible with a broad range of
multi-channel audio signals, providing reliable operation with HDMI sources.
Transmitter HDMI loop-through with selectable audio control — Features an active
HDMI output with support for embedded audio for connection to a local monitor.
Transmitter selectable analog stereo audio input embedding — Supports balanced
or unbalanced audio for extended transmission by embedding stereo audio into the signal
stream. This feature enables direct connection of separate stereo audio signals from a
laptop, Blu-ray Disc player, or other device.
Receiver HDMI audio de-embedding with analog stereo and digital S/PDIF audio
outputs — Digital HDMI audio is made available as a balanced or unbalanced analog
stereo signal on captive screw connectors or a S/PDIF connector.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Introduction
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and
Operation
This section contains the installation procedures for and operation of the XTP T HDMI and
the XTP R HDMI. Topics in this section include:
•
•
•
XTP HDMI transmitters and receivers can be mounted in a rack or under a desk or placed
Cabling
XTP T HDMI Rear Panel Connectors
g
a
b
c
d
e f
SIG
LINK
INPUTS
POWER
12V
1.0 A MAX
AUDIO
ON
OVER XTP
AUDO
L
R
RS-232
IR
RESET
OFF
+
−
+
−
HDMI
LOOP-THRU
Tx Rx
G
Tx Rx
XTP OUT
LAN
Figure 2. XTP T HDMI Rear Panel Connectors
NOTES:
• For HDMI cables, the maximum cable length is 15 feet.
• Use Extron LockIt lacing brackets to secure HDMI connectors to the device (see
HDMI LockIt on page 8).
• Video input from a DisplayPort source must be a dual mode DisplayPort source.
HDMI input connector — Connect a digital video source to the female HDMI
connector. It can accept HDMI, DVI (with an appropriate adaptor), or DisplayPort video
signals.
a
b
HDMI Loop-thru connector — Connect a digital video display to the female HDMI
page 14 to select local audio output options). Displays that are not HDCP compliant
display a green screen when HDCP encrypted content is sent to them.
Analog audio inputs — Connect a balanced or unbalanced analog audio source to
the 5-pole captive screw connector for stereo analog audio input.
c
Tip
Tip
Ring
Sleeve
Sleeves
Tip
Ring
Tip
Do not tin the wires!
Sleeve
Balanced Audio Input
Unbalanced Audio Input
Figure 3.
Audio Input Wiring
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
4
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 Over XTP port — To pass bidirectional serial, Infrared, or other
control signals between XTP-compatible devices, connect a control device
to the 5-pole captive screw connector. The port includes only the 3 poles
labeled “RS-232.”
RS-232
IR
d
Tx Rx G Tx Rx
RS-232
IR
IR Over XTP port — To enable the ability to transmit and receive IR
signals (up to 40 kHz), connect a control device to the 5-pole captive screw
connector. This port includes only the 2 poles labeled “IR” and shares the
ground pole with the RS-232 port.
Tx Rx G Tx Rx
NOTE: RS-232 and IR data can be transmitted simultaneously (see
RS-232 and IR Communication on page 10 for wiring details).
XTP connector — Connect a twisted pair cable to the RJ-45 connector labeled
XTP Out and the XTP input port on another XTP device to pass all signals (see TP
following signals:
e
•
•
•
•
•
•
Digital video
Digital audio
Bidirectional RS-232 and IR commands
Remote power
Ethernet communication
System communication
The Link LED lights amber when XTP devices are connected and communication is
established.
The Signal LED lights green when the transmitter outputs video signal or test pattern.
ATTENTION:
• Do not connect this connector to a computer data or telecommunications
network.
• XTP remote power is intended for indoor use only. No part of the network that
page 12).
LAN connector — Connect a control device or device to be controlled to the
transmitter for 10/100 Ethernet communication through this pass-through port. LEDs
on the connector indicate link and activity status.
f
g
Power connector and LED — Connect the external 12 V, 1.0 A power supply into the
2-pole captive screw connector. The Power LED lights to indicate the device is receiving
power.
NOTE: XTP HDMI transmitters and receivers can also be powered remotely
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
5
Download from Www.Somanuals.com. All Manuals Search And Download.
XTP R HDMI Rear Panel Connectors
h
a b
c
d
e f g
OUTPUTS
RELAYS
SIG
LINK
POWER
12V
1.0 A MAX
OVER XTP
AUDIO
AUDIO
ON
1
2
L
R
RS-232
IR
RESET
OFF
Tx Rx
G
Tx Rx
+
-
+
-
HDMI
LAN
S/PDIF
XTP IN
Figure 4. XTP R HDMI Connectors
XTP connector — Connect a twisted pair cable to the RJ-45 connector labeled
a
XTP In on the receiver and to an XTP output port on another XTP device to receive all signals
following signal:
•
•
•
•
•
•
Digital video
Digital audio
Bidirectional RS-232 and IR commands
Remote power
Ethernet communication
System communication
The Link LED lights amber when XTP devices are connected and communication is
established.
The Signal LED lights green when the receiver receives an active HDMI video signal or a test
pattern from the transmitter.
ATTENTION:
• Do not connect this connector to a computer data or telecommunications network.
• XTP remote power is intended for indoor use only. No part of the network that uses
LAN connector — Connect a control device or device to be controlled to the transmitter
for 10/100 Ethernet communication through this pass-through port. LEDs on the connector
indicate link and activity status.
b
c
RS-232
IR
RS-232 Over XTP port — To pass bidirectional serial, Infrared, or other control
signals between XTP-compatible devices, connect a control device to the 5-pole
captive screw connector. The port includes only the 3 poles labeled “RS-232.”
Tx Rx G Tx Rx
IR Over XTP port — To enable the ability to transmit and receive IR signals (up to
40 kHz), connect a control device to the 5-pole captive screw connector. This port
includes only the 2 poles labeled “IR” and shares the ground pole with the RS-232
port.
RS-232
IR
Tx Rx G Tx Rx
Communication on page 10 for wiring details).
Audio Switch on page 14 to select local audio output options). It can accept HDMI, DVI (with
an appropriate adaptor), or DisplayPort video signals.
d
NOTES:
• Maximum cable length is 15 ft.
• Use Extron LockIt lacing brackets to secure HDMI connectors to the device (see
HDMI LockIt on page 8).
• Video input from a DisplayPort source must be a dual mode DisplayPort source.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Analog audio output — Connect a balanced or unbalanced, stereo or mono audio
output device to the 3.5 mm, 5-pole captive screw connector for 2-channel stereo
analog audio output. If the device is receiving 2-channel LPCM embedded on the HDMI
input signal and digital is the selected audio input format, it is extracted and converted
to a stereo analog signal.
e
No Ground Here
Tip
Ring
Sleeves
Tip
Tip
Sleeves
Tip
Do not tin the wires!
Ring
No Ground Here
Balanced Audio Output
Unbalanced Audio Output
Figure 5.
Audio Output Wiring
ATTENTION: For unbalanced audio, connect the sleeves to the center contact
ground. Do not connect the sleeves to the negative (-) contacts.
S/PDIF audio output — Connect an audio device to the female orange RCA
for supported audio formats on the S/PDIF output). The type of audio present on this
output will be dictated by the following:
f
•
The audio format selected on the source material or device.
•
The source device automatically outputting an audio format through EDID.
Relays — Connect equipment that can be controlled via momentary or latching
contact, like as projector screens or lifts, to the normally open relays.
g
h
ATTENTION: Do not exceed 24 V at 1.0 A for each port.
Power connector and LED — Connect the external 12 V, 1.0 A power supply to the
2-pole captive screw connector. The Power LED lights to indicate the device is receiving
power.
NOTE: XTP HDMI transmitters and receivers can be powered remotely
Front Panel Configuration Port
INPUT
SIGNAL
HDMI AUDIO
CONFIG
AUDIO SIGNAL CLIP
HDCP
ANALOG AUDIO
XTP T HDMI
XTP T HDMI
a
XTP
AUDIO
SIGNAL
HDCP
HBR
BITSTREAM
S/PDIF
LPCM
CONIG
HDMI
ANALOG
XTP R HDMI
XTP R HDMI
Figure 6. Front Panel Configuration Port
Front Panel Config Port — Connect a host device to the female mini-USB B port to
configure the connected transmitter or receiver or update firmware.
a
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Making Connections
HDMI LockIt
Use an Extron LockIt Lacing Bracket to secure an HDMI cable to each device as follows:
1. Plug the HDMI cable into the panel connection.
3
4
2
5
1
Figure 7.
Installing the LockIt Lacing Bracket
2. Loosen the HDMI connection mounting screw from the panel enough to allow the
LockIt lacing bracket to be placed over it. The screw does not have to be removed.
3. Place the LockIt lacing bracket on the screw and against the HDMI connector, then
tighten the screw to secure the bracket.
ATTENTION: Do not overtighten the HDMI connector mounting screw. The shield
it fastens to is very thin and can easily be stripped.
4. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing
bracket (see figure 7).
5. While holding the connector securely against the lacing bracket, use pliers or similar
tools to tighten the tie wrap, then remove any excess length.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TP Cable Termination and Recommendations
Use the following pin configurations for twisted pair cables.
Pins:
12345678
Straight-through Cable
(for connection to a switch, hub, or router)
TIA/EIA T 568 A
Pin Wire Color
TIA/EIA T 568 B
Pin Wire Color
1
2
3
4
5
6
7
8
White-green
Green
1
2
3
4
5
6
7
8
White-orange
Orange
White-orange
Blue
White-green
Blue
White-blue
Orange
White-blue
Green
Insert Twisted
Pair Wires
White-brown
Brown
White-brown
Brown
RJ-45
Connector
Figure 8. TP Cable Termination
Supported cables
The XTP T HDMI and XTP R HDMI are compatible with CAT 5e, 6, 6a, and 7 shielded
twisted pair (F/UTP, SF/UTP, and S/FTP) and unshielded twisted pair (U/UTP) cable.
ATTENTION:
• Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable or STP201 cable
to link the XTP products.
• To ensure FCC Class A and CE compliance, STP cables and STP connectors are
required.
Cable recommendations
Extron recommends using the following practices to achieve full transmission distances up
to 330 feet (100 m) and reduce transmission errors.
•
Use the following Extron XTP DTP 24 SF/UTP cables and connectors for the best
performance:
•
•
•
XTP DTP 24/1000
XTP DTP 24P/1000 Plenum 1000' (305 m) spool
XTP DTP 24 Plug Package of 10
Non-Plenum 1000' (305 m) spool
22-236-03
22-235-03
101-005-02
•
If not using XTP DTP 24 cable, at a minimum, Extron recommends 24 AWG, solid
conductor, STP cable with a minimum bandwidth of 400 MHz.
•
•
Terminate cables with shielded connectors to the TIA/EIA T 568 B standard.
Limit the use of more than two pass-through points, which may include patch points,
punch down connectors, couplers, and power injectors. If these pass-through points
are required, use CAT 6 or 6a shielded couplers and punch down connectors.
NOTE: When using CAT 5e or CAT 6 cable in bundles or conduits, consider the
following:
• Do not exceed 40% fill capacity in conduits.
• Do not comb the cable for the first 20 m, where cables are straightened, aligned,
and secured in tight bundles.
• Loosely place cables and limit the use of tie wraps or hook and loop fasteners.
• Separate twisted pair cables from AC power cables.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
9
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 and IR Communication
The RS-232 and IR Over XTP connector is for pass-through transmission of serial signals,
such as projector control signals, and Infrared data (see figure 9 below for an example of
how to wire the connector).
Custom
IR Device
Rx Tx
G
Tx/Rx
Pins
Tx Rx
G
RS-232 Device
Figure 9. Wiring the RS-232 and IR Connector
Cross the Tx and Rx lines once between the source and target.
ATTENTION: The length of exposed wires is critical. The ideal length is
3/16 inch (5 mm).
• Longer bare wires can short together
• Shorter wires are not as secure in the connectors and could be pulled out.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Connection
Apply power to the transmitter or receiver locally with the provided power supply or remotely
with a power injector or a matrix switcher.
ATTENTION: XTP remote power is intended for indoor use only. No part of the network
that uses XTP remote power should be routed outdoors.
Local power
2-Pole Captive Screw
Connector
Tie Wrap
SECTION A–A
3/16”
(5 mm) Max.
Smooth
Ridges
A
A
Power Supply
Output Cord
Figure 10. Power Wiring
Both the XTP T HDMI and the XTP R HDMI can be connected to a local power supply.
WARNING: Electric shock hazard. The two power cord wires must be kept separate
while the power supply is plugged in. Remove power before wiring.
ATTENTION:
• This product is intended to be supplied by a Listed Power Unit marked “Class 2”
or “LPS,” rated 12 VDC, 1.0 A minimum. Always use a power supply supplied by
or specified by Extron. Use of an unauthorized power supply voids all regulatory
compliance certification and may cause damage to the supply and the end product.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The installation must always be in accordance with the
applicable provisions of National Electrical Code ANSI/NFPA 70, article 75 and
the Canadian Electrical Code part 1, section 16. The power supply shall not be
permanently fixed to a building structure or similar structure.
• Power supply voltage polarity is critical. Incorrect voltage polarity can damage the
power supply and the unit. The ridges on the side of the cord identify the power cord
negative lead.
• The length of the exposed (stripped) copper wires is important. The ideal length is
3/16 inch (5 mm).
TIP: Do not tin the stripped power supply leads. Tinned wires are not as secure in the
captive screw connectors. Tinned wires are not as secure in the captive screw
connectors and could be pulled out.
Use the supplied tie wrap to strap the power cord to the extended tail of the connector.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote power
The XTP HDMI transmitter and receiver can be powered remotely through an XTP Power
Injector or through an XTP matrix switcher.
ATTENTION: XTP remote power is intended for indoor use only. No part of the network
that uses XTP remote power should be routed outdoors.
Power injector
To power XTP HDMI transmitters and receivers remotely with an XTP Power Injector, power
the XTP cable run along the XTP ports (see the XTP Power Injector User Guide for more
installation information).
NOTE: The power injector provides remote power up to 330 feet with a CATx cable with
24 AWG wire.
12 V Local Power
Supply
0
-
0
-
6
/
0
H
z
P
T P P W R
Remote
Power
T
E
S
E
R
P
R
K
IN
L
IG
SIG
S
Extron
XTP PI 100
XTP Power
Injector
CT
LAN
LAN
LINK
IR
OVER XT
X
T
P
P
OUT
OUT
2
3
2
-
CATx Cable
S
R
x
R
O
x
T
R
G
AUDI
L
x
R
Tx
−
+
O
AUDI
−
ON
+
OFF
INPUTS
U
R
H
T
P
O
O
L
I
M
POW
12V
D
H
--A M
T
E
S
E
HDMI
R
YS
RELA
2
1
OUTPUTS
Extron
AUDIO R
L
S/PDI
XTP T HDMI
+
-
+
XTP Transmitter
AUDIO
ON
I
M
D
H
OVER IRTP
X
OFF
HDMI
2
3
2
-
S
R
x
R
x
G
x
R
x
T
SIG
ACTLAN LINK
POWER
12V
--A M
X
IN
IN
Blu-Ray
Player
Extron
XTP R HDMI
XTP Receiver
Display
Figure 11. Typical Point-to-Point Application with Remote Power
Direct power from an XTP matrix switcher
XTP matrix switchers have a fixed amount of power available to provide remote power
to connected XTP endpoints (refer to the user guide of the XTP matrix switcher for more
details). To manage available power from the XTP matrix switcher, use the XTP System
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
After all transmitters, all receivers, and their connected devices are powered up, the system
is fully operational. If any problems are encountered, verify that the cables are routed and
connected properly. If problems persist, call the Extron S3 Sales & Technical Support
Hotline. See the contact numbers on the last page of this guide for the nearest Extron office.
XTP T HDMI Front Panel Indicators
INPUT
SIGNAL
HDCP
HDMI AUDIO
ANALOG AUDIO
CONFIG
AUDIO SIGNAL CLIP
XTP T HDMI
a
b
Figure 12. XTP T HDMI Front Panel Features
Power LED — Lights when power is applied to the device from the power supply or
remotely from an XTP Power Injector or XTP matrix switcher. There are two Power LED
indicators, one on left side of the front panel and one on the left side of the rear panel.
a
b
Input indicators
Signal LED — Lights when an active video signal is detected from the source.
HDCP LED — Lights when the input signal is encrypted.
HDMI Audio LED — Lights when the HDMI audio input is selected.
Analog Audio LED — Lights when the analog audio input is selected.
Audio Signal Clip LED — Lights when the analog audio input signal remains above
-3 dBFS. The LED remains lit for 200 milliseconds after the signal falls below -3 dBFS.
XTP R HDMI Front Panel Indicators
XTP
AUDIO
SIGNAL
CONFIG
HBR
BITSTREAM
LPCM
HDCP
HDMI
S/PDIF
ANALOG
XTP R HDMI
Figure 13. XTP R HDMI Front Panel Features
Power LED — Lights when power is applied to the device from the power supply or
remotely from an XTP Power Injector or XTP matrix switcher, such as an
XTP CrossPoint. There are two Power LED indicators, one on left side of the front panel
and one on the left side of the rear panel.
a
XTP indicators
b
Signal LED — Lights when an active XTP input signal is received.
HDCP LED — Lights when the input signal is encrypted.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio indicators
c
HBR LED — Lights when the input audio signal is high bit rate audio.
Bitstream LED — Lights when the input audio signal is a Dolby® Digital, DTS® audio
format and 2-channel Dolby.
LPCM LED — Lights when the input audio signal is LPCM-2Ch.
HDMI LED — Lights when the input audio format is multi-channel, LPCM-2Ch, or
Hi-Def audio.
S/PDIF LED — Lights when the input audio format is multi-channel (except HBR), or
LPCM-2Ch,
Analog LED — Lights when the input audio format is LPCM-2Ch.
HDMI Audio Switch
AUDIO
ON
The XTP T HDMI and XTP R HDMI have an HDMI audio switch that mutes the
embedded audio on the related HDMI connector. On the XTP T HDMI, the audio
switch mutes or enables the audio on the HDMI loop-thru connector. On the
XTP R HDMI, the audio switch mutes or enables the audio on the HDMI output
connector. The LED next to the switch lights when HDMI audio is enabled.
OFF
Move and hold the rear panel HDMI audio switch up for about 1 second to enable
embedded audio on the associated HDMI connector, or move and hold the HDMI audio
switch down for about 1 second to disable embedded audio on the associated HDMI
connector. The switch returns to the middle position after it has been released so the device
can continue to be controlled through SIS commands.
EDID
NOTE: In matrix applications, EDID on the transmitter is assigned by the matrix
switcher using the XTP System Configuration Software.
The XTP T HDMI can record and save EDID in a user memory location on the transmitter.
EDID can come from the loop-through display on the transmitter or the output display on
the receiver (default). Connect a host device to the XTP transmitter for EDID control (see
page 23).
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Output Overview
By default, the XTP HDMI transmitter prioritizes embedded digital audio over analog audio.
Use SIS commands or the XTP System Configuration Software to manually select the audio
Software on page 23).
Audio Output
Audio Input Format
LPCM up to 7.1, 24 bit, 192 kHz
Multi-channel PCM
Dolby Digital 2/0
HDMI
S/PDIF
Analog
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Dolby Digital 2/0 Surround
Dolby Digital 5.1
Dolby Digital EX
Dolby Digital Plus
Dolby TrueHD
DTS 2 Channel
X
X
X
X
DTS Digital Surround 5.1
DTS-ES Matrix 6.1
DTS-ES Discrete 6.1
DTS-HD
DTS-HD Master Audio
NOTE: The transmitter uses a black signal to simulate a 720p or 1080p, 50 Hz or 60 Hz
signal so audio can be passed without video.
Reset Modes
Use the recessed Reset button on the rear panel of the transmitter or receiver to
RESET
return the device to default settings or to restore factory-shipped firmware.
Reset Mode Summary
Mode Mode Activation
Result
Purpose/Notes
1
Hold the recessed Reset
button down while applying
power to the device.
The device reverts to the
factory default firmware.
Use mode 1 to roll back to factory
firmware for a single power cycle
if an incompatibility issue arises.
NOTE: After a mode 1
reset, update the device
with the latest firmware
version. DO NOT operate
the firmware version that
results from this mode
reset.
NOTE: If you do not want
to update the firmware or
perform a mode 1 reset
by mistake, cycle power
to the device to return the
firmware version running
prior to the reset.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Installation
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SIS Configuration
and Control
The XTP T HDMI and XTP R HDMI can be configured and controlled using Extron
Simple Instruction Set (SIS) commands or the XTP System Configuration Software (see
XTP System Configuration Software on page 23). This section contains basic SIS
communication details and SIS commands and responses when connected directly to an
XTP T HDMI or XTP R HDMI. Topics in this section include:
•
•
•
•
Host Device Connection
Use a computer running the HyperTerminal or Extron DataViewer utility, or a control system
to make serial control of the transmitter and receiver possible. To connect directly to an
XTP T HDMI or XTP R HDMI, connect the computer to the XTP HDMI transmitter or receiver
through the front panel USB Config port.
SIS Programming Guide
Host-to-Device and Device-to-Host Communication
SIS commands consist of one or more characters per field. No special characters are
required to begin or end a command sequence. When the XTP T HDMI or the XTP R HDMI
determines that a command is valid, it executes the command and sends a response to the
host device. All responses from the transmitter or receiver to the host end with a carriage
return and a line feed (CR/LF = ]), which signals the end of the response character string.
A string is one or more characters.
XTP T HDMI Transmitter and XTP R HDMI Receiver • SIS Configuration and Control
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Error Responses
When the XTP T HDMI or the XTP R HDMI receives an SIS command and determines that it
is valid, it performs the command and sends the corresponding response to the host device.
If the command is determined invalid or contains invalid parameters, the transmitter or
receiver returns an error response to the host. The error response codes are:
E01= Invalid input number
E10= Invalid command
E12= Invalid port number
E13= Invalid parameter
E14= Not valid for this configuration
E17= Invalid command for signal type
E22= Busy
Using the Command and Response Table for SIS Commands
The command and response tables begin on page 19. Figure 14 shows the hexadecimal
equivalent of ASCII characters used in the command and response tables.
NOTE: Uppercase and lowercase text can be used interchangeably unless otherwise
stated.
ASCII to Hex Conversion Table
Space
•
Figure 14. ASCII to Hexadecimal Conversion
Symbol definitions
= Carriage return and line feed
]
= Carriage return with no line feed
¦ or }
•
= Space
= Escape key
Eor W
XTP T HDMI Transmitter and XTP R HDMI Receiver • SIS Configuration and Control
17
Download from Www.Somanuals.com. All Manuals Search And Download.
= EDID Emulation
See the table below
X2@
EDID Emulation Table (where X2@= the SIS value)
SIS
Resolution
Refresh
Output
Value
Rate (Hz)
1
Receiver output
Transmitter loop-through output
2
3
800x600
1024x768
60
60
60
60
60
60
60
60
60
60
60
60
60
60
50
50
50
50
50
50
50
50
50
50
DVI
DVI
HDMI
DVI
DVI
DVI
DVI
DVI
DVI
DVI
DVI
DVI
HDMI
DVI
DVI
DVI
HDMI
DVI
DVI
DVI
DVI
DVI
DVI
DVI
4
5
1280x720 with 2-ch audio*
1280x768
6
7
1280x800
8
1280x1024
9
1360x768
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
1366x768
1400x1050
1440x900
1600x1200
1680x1050
1920x1080 with 2-ch audio
1920x1200
800x600
1024x768
1280x720 with 2-ch audio
1280x768
1280x800
1280x1024
1360x768
1366x768
1400x1050
1440x900
* = default
XTP T HDMI Transmitter and XTP R HDMI Receiver • SIS Configuration and Control
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Command and Response Tables for Transmitter SIS Commands
The following commands are for direct connections to the XTP T HDMI (see to the XTP
matrix switcher user guide for commands that can be sent from the matrix to endpoints).
Command
ASCII Command Response
Additional Description
(Host to Device)
(Device to Host)
Audio Configuration
Input audio format selection
Set input audio selection
Set which audio input signal the
transmitter will send. Auto will prioritize
digital over analog audio.
EIX&AFMT} AfmtIX&]
View input audio selection
View the input audio format setting.
EIAFMT}
AfmtIX&]
Audio gain and attenuation
NOTE: Audio gain (G) and attenuation (g) are case sensitive.
Set audio gain
X1@G
X1#g
AudX1@]
AudX1#]
Sets audio gain on current input to X1@.
Sets audio attenuation on current input
to X1#.
Set audio attenuation
+G
-G
G
Increase gain
Decrease gain
View gain
Increments audio level.
AudX1$]
AudX1$]
AudX1$]
Decrements audio level.
View the audio level of the current input.
Loop-through audio mute
1Z
0Z
Z
Mute loop-through audio
Mute the embedded audio.
Amt1]
Amt0]
AmtX1%]
Unmute the loop-through audio
Unmute the embedded audio.
View the embedded audio mute status.
View loop-through audio mute
status
Black signal for audio only
NOTE: The transmitter uses a black signal to simulate a 720p or 1080p, 50 Hz or 60 Hz signal so audio can
be passed without video.
Set black signal resolution
View black signal resolution
Enable black signal
Set the black signal resolution.
View the current black signal resolution.
Enable the black signal for audio only.
Disable the black signal.
EAX2)AFMT} AfmtAX2)]
EAAFMT}
EB1AFMT}
EB0AFMT}
EBAFMT}
AfmtAX2)]
AfmtB1]
Disable black signal
AfmtB0]
View black signal
View the black signal status.
AfmtBX@]
NOTE: X@= Enable or disable
X&= Input audio format
0= off or disable
1= on or enable
0= auto (default)
1= digital or embedded
2= analog
X1@= Audio gain
X1#= Audio attenuation
X1$= Audio level
0- 24= decibels above 0
–18- 0= decibels below 0
–18- +24(0dB = default)
X1%= Audio mute
0= unmute all
1= mute loop-through audio
X2)= Black signal resolution
2= 1280 x 720p, 50 Hz
4= 1280 x 720p, 60 Hz (default)
6= 1920 x 1080p, 60 Hz
XTP T HDMI Transmitter and XTP R HDMI Receiver • SIS Configuration and Control
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Command
ASCII Command
Response
Additional Description
(Host to Device)
(Device to Host)
EDID
Set EDID information
Set the EDID resolution and refresh
rate.
EAX2@EDID} EdidAX2@]
View EDID information
View the EDID resolution and
refresh rate.
EAEDID}
EdidAX2@]
Advanced Configuration
HDCP authorized device
HDCP authorized device on
Set the transmitter as an HDCP
authorized device.
EE1HDCP}
EE0HDCP}
EEHDCP}
HdcpE1]
HdcpE0]
HdcpEX2!]
HDCP authorized device off
Set the transmitter as not an HDCP
authorized device.
View HDCP authorized
device setting
View the HDCP authorized device
setting.
Video mute
1B
Mute output to black
Mutes video and displays a black
screen.
Vmt1]
0B
B
Unmute output
Unmute the video.
Vmt0]
View the video mute status
View the video mute status.
VmtX*]
Test pattern
Set test pattern
X^J
J
TstX^]
TstX^]
Set color bars test pattern to X^.
View the current test pattern.
View test pattern
Reset mode
Reset to factory defaults
Resets all user settings back to
factory defaults.
EZXXX}
Zpx]
Status
OLS
View input signal presence
Query HDCP input
Query firmware version
Query full firmware version
Query part number
View the input signal presence.
Query the HDCP status.
FrqX1^]
EIHDCP}
Q
HdcpIX(]
x.xx]
Query the firmware version.
Query the full firmware version.
Query the device part number.
*Q
N
x.xx.xxxx]
60-1043-12]
NOTE: X^= Color bars test pattern
0= off (default)
1= 1280x720p at 50 Hz
3= 1280x720p at 60 Hz
5= 1920x1080p at 60 Hz
X*= Video mute
X(= HDCP status
0= off or disabled
1= on or enabled (mute to black)
0= no source connected
1= HDCP-compliant source connected
2= non-HDCP-compliant source connected
X1^= Video signal status
0= video or TMDS signal not detected
1= video or TMDS signal detected
X2!= HDCP authorized device status
X2@= EDID emulation
0= off
1= on (default)
XTP T HDMI Transmitter and XTP R HDMI Receiver • SIS Configuration and Control
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Command and Response Tables for Receiver SIS Commands
The following commands are for direct connection to the XTP R HDMI (refer to the XTP
matrix switcher user guide for commands that can be sent from the matrix to endpoints).
Command
ASCII Command Response
Additional Description
(Host to Device)
(Device to Host)
Audio Configuration
Volume control
Set volume
X1!V
+V
VolX1!]
VolX1!]
VolX1!]
VolX1!]
Set the output volume to X1!.
Increase the audio volume.
Increment volume
Decrement volume
View volume
-V
V
Decrease the audio volume.
View current volume setting.
Audio mute
3Z
0Z
Z
Mute all
Mute the audio.
Amt3]
Unmute all
Unmute the audio.
View the mute status.
Amt0]
View mute status
AmtX1%]
Advanced Configuration
Relay control
Pulse relay
X1&*3*X1(O
X1&*2O
X1&*1O
X1&*0O
X1&O
RlyX1**X@]
RlyX1**X@]
RlyX1**1]
RlyX1**0]
RlyX1**X@]
Pulse relay X1*for X1(ms.
Toggle relay X1*.
Toggle relay
Turn relay on
Turn relay X1*on.
Turn relay off
Turn relay X1*off.
View relay status
Mute video to black
Mute video to black
Unmute video
View the on or off status of relay X1*.
1B
0B
B
Mute the video and display black video.
Unmute the video.
Vmt1]
Vmt0]
VmtX*]
View video mute status
Reset mode
View the video mute setting.
Reset to factory defaults
Resets all user settings back to factory
defaults.
EZXXX}
Zpx]
NOTE: X@= Enable or disable
X*= Video mute
0= off or disable
1= on or enable
0= off or disable (default)
1= on or enable (mute to black)
X1!= Audio volume
X1%= Audio mute
0- 64(64= default)
0= unmute all
3= mute all
X1*= Relay number
X1(= Pulse time
1= relay 1
2= relay 2
1-65,535(in 16 ms increments)
XTP T HDMI Transmitter and XTP R HDMI Receiver • SIS Configuration and Control
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Command
Status
ASCII Command
Response
Additional Description
(Host to Device)
(Device to Host)
0LS
View input signal presence
View the input signal presence.
Query the HDCP status.
FrqX1^]
Query HDCP output
Query firmware version
Query full firmware version
Query part number
EOHDCP}
Q
HdcpOX(]
x.xx]
Query the firmware version.
Query the full firmware version.
Query the device part number.
*Q
N
x.xx.xxxx]
60-1043-13]
NOTE: X(= HDCP status
0, 2, 4, or 6= no output connected
1, 3, or 5= display connected and not currently encrypted
7= display connected and currently encrypted
X1^= Video signal status
0= video or TMDS signal not detected
1= video or TMDS signal detected
XTP T HDMI Transmitter and XTP R HDMI Receiver • SIS Configuration and Control
22
Download from Www.Somanuals.com. All Manuals Search And Download.
XTP System
Configuration
Software
This section contains installation and configuration procedures for the XTP System
Configuration Software to configure and control XTP HDMI transmitters and receivers.
Topics in this section include:
•
•
The XTP System Configuration Software is convenient, user-friendly control software for
configuring an XTP system or individual XTP devices.
Installing the XTP System Configuration Software
The program is contained on the Extron Software DVD or available for download on the
To install the software from the DVD:
1. To install the software, insert the DVD into the DVD drive. The Extron software DVD
window should appear automatically. If it does not self-start, run Launch.exe from the
DVD.
2. Click the Softwaretab, scroll to the desired program, and click Install.
3. Follow the instructions that appear on the screen. By default, the installation creates an
Extron directory in the Program Files folder, and places four icons into a group folder
named “Extron Electronics\XTP System Configuration.”
XTP T HDMI Transmitter and XTP R HDMI Receiver • XTP System Configuration Software
23
Download from Www.Somanuals.com. All Manuals Search And Download.
To download the software from the website:
Figure 15. Extron Website Download Page
1. On the Extron website, click the Downloadtab.
2. From the left sidebar, click the Softwarelink.
3. Navigate to XTP System Configuration.
4. Click the Downloadlink to the right of the desired device.
5. Submit any required information to start the download. Note where the file is saved.
6. Open the executable (.exe) file from the save location.
7. Follow the instructions that appear on the screen. By default, the installation creates a
directory in the Program Files folder, and places four icons into a group folder named
“Extron Electronics\XTP System Configuration.”
Using the XTP System Configuration Software
XTP HDMI transmitters and receivers can be controlled directly from the front panel Config
port or remotely from a connected XTP matrix switcher.
Connection
When opening the XTP System Configuration Software, the Connections screen opens first.
This screen is used to establish communication with an XTP device via USB
1. From the Connections screen, select the USBradio button.
2. Select the connected device to be controlled from the displayed list.
3. Click the Connectbutton.
XTP T HDMI Transmitter and XTP R HDMI Receiver • XTP System Configuration Software
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmitter Configuration
The Device Settings screen allows a user to view and edit various device settings of the
transmitter connected to the host device.
Transmitter device settings
When connected directly to an XTP T HDMI, the Device Settings screen contains
configuration options for the transmitter only. Click the Device Settingsicon on the
Global Navigation bar to open the Device Settings screen.
Figure 16. Transmitter Device Settings Screen
Video panel
Video input — Select the HDCP Authorizedcheck box to set the transmitter as an HDCP
authorized device or deselect it to indicate that the device is not an HDCP authorized
device. This is checked by default.
Video output — Select or deselect the Color Bars Test Patterncheck box to transmit
or not transmit a test pattern to an XTP receiver. This is not selected by default. If a color
bars text pattern is enabled, select a signal type from the Signal Typedrop-down list.
Audio panel
Switch mode select — Select the Autoradio button to enable Auto Switch mode (default).
When in Auto Switch mode, HDMI audio has priority over analog audio. Select the Manual
radio button to disable Auto Switch mode.
Audio input select — If the switch mode is set to Manual, select the HDMIradio button to
transmit embedded audio from an HDMI signal or select the Analogradio button to transmit
an analog audio signal.
Analog audio — If the transmitter transmits analog audio, move the Analog Audio Gain
slider up or down or select the gain in the field below the slider to adjust the audio gain or
attenuation in decibels.
Audio output — Select the Allow Audio Onlycheck box to enable the black signal for
audio-only transmission. This is not selected by default.
If enabled, select the black signal resolution from the Signal Typedrop-down list. The
default resolution is 720p @ 60 Hz.
XTP T HDMI Transmitter and XTP R HDMI Receiver • XTP System Configuration Software
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Factory reset
Click the Factory Resetbutton to reset the transmitter to factory settings except for
firmware.
NOTE: This is the same as the EZXXXSIS command.
EDID Minder
Use the EDID Minder screen to assign unique EDID to the input or match current output
resolutions to the input. This feature is only available for the XTP transmitters. Click the EDID
Mindericon on the global navigation bar. The EDID Minder screen opens.
The EDID Minder screen displays a table of EDID options and connected output devices,
which are each represented by output display icons. Factory default EDID options are
displayed in blue and connected output devices are displayed in green. Custom loaded or
saved EDID options are displayed in yellow. Output resolutions are displayed in green.
Figure 17. EDID Minder Screen
Assign EDID
1. Select an available EDID setting (represented by a blue, green, or yellow output display
icon) from the Available EDID pane.
2. Select the check box of the connected input to the right of the Available EDID pane.
3. Click the Assignbutton below the input area.
TIP: Alternatively, EDID can be assigned by dragging and dropping the desired EDID
onto the input.
XTP T HDMI Transmitter and XTP R HDMI Receiver • XTP System Configuration Software
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Import EDID
1. On the EDID Minder screen, click the Add EDID to Librarybutton.
2. Select the desired EDID file and click Open. The EDID setting appears in the Available
EDID pane.
3. Assign the EDID from the Available EDID pane to import the EDID setting to the device.
Save output EDID
1. On the EDID Minder screen, right-click on the desired EDID setting in the Connected
Outputspane.
2. Select the Save EDID to PCoption. The EDID setting is saved to the connected PC.
Alternatively, right-click on the desired EDID, select Copy, and then Pastethe EDID into
the desired pane.
Set favorite EDID
Commonly used EDID settings can be added to the Favorites pane for quick access.
1. Click and drag the desired EDID setting to the Favorites pane. The EDID is copied to the
Favorites pane. Alternatively, right-click the desired EDID and select Copy. Then Paste
the EDID setting into the Favorites pane.
EDID filters
The filters can be used to easily and quickly locate specific EDID. Selectable filters include:
•
•
•
•
Resolution
Refresh rate
Audio format
Video format
To use a filter or combination of filters:
1. Select an EDID setting from one of the drop-down lists of the associated filter. The
available EDID options that match the filter selection are displayed in the Available EDID
pane.
2. Repeat step 1 to apply more filters.
To clear the currently applied filters:
1. Click the Clearbutton next to the filters. All filters are reset.
Common timings
This function automatically displays available EDID settings that are common among
multiple selected outputs or EDID files.
1. Hold <Ctrl> and click the desired outputs in the Connected Outputs pane. The Common
Timingstab appears to the right of the pane, listing the EDID settings common among
the selected outputs.
2. Select the desired common EDID setting. The EDID setting will be shown in the
Available EDID pane.
XTP T HDMI Transmitter and XTP R HDMI Receiver • XTP System Configuration Software
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiver Configuration
When connected directly to an XTP R HDMI, the Device Settings screen contains
configuration options for the receiver only.
Figure 18. Receiver Device Settings Screen
Video panel
Video mute — Click the Video Mutebutton to mute to black or unmute the video output.
NOTE: The button turns red when the video output is muted.
Relay Control panel
Toggle — Click the Togglebutton under the desired relay section to toggle the relay.
NOTE: The Status indicator displays Openwhen the relay is open and Closedwhen the
relay is closed.
Pulse — Select a length of time from the Durationfield under the desired relay section and
click the Pulsebutton to pulse the relay.
Audio panel
Mute All — Click the Mute Allbutton to mute or unmute all audio outputs.
NOTE: The button turns red when the output HDMI embedded audio is muted.
Analog audio — If applicable, move the Analog Audio Volumeslider up or down or
select an amount in the field below the slider to adjust the audio volume in decibels.
Factory reset
Click the Factory Resetbutton to reset the receiver to factory settings except for
firmware.
NOTE: This is the same as the EZXXXSIS command.
XTP T HDMI Transmitter and XTP R HDMI Receiver • XTP System Configuration Software
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference
Information
This section contains mounting information and instructions for updating firmware. Topics in
this section include:
•
•
Mounting
The XTP T HDMI and the XTP R HDMI can be placed on a tabletop or mounted in a rack or
underneath a desk.
Tabletop Mounting
Attach the provided rubber feet to the bottom four corners of the enclosure.
Mounting Kits
Mount the unit using any optional compatible rack shelf or mounting kit listed on the Extron
UL guidelines for rack-mounted devices
The following Underwriters Laboratories (UL) guidelines pertain to the safe installation of the
XTP T HDMI and XTP R HDMI in a rack.
1. Elevated operating ambient temperature — If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be greater
than room ambient temperature, Therefore, install the XTP T HDMI and XTP R HDMI in
an environment compatible with the maximum ambient temperature
(Tma = +122 ˚F, +50 ˚C) specified by Extron.
2. Reduced air flow — Install the equipment in a rack so that the amount of air flow
required for safe operation of the equipment is no compromised.
3. Mechanical loading — Mount the equipment in the rack so that a hazardous
condition is not achieved due to uneven mechanical loading.
4. Circuit overloading — Connect the equipment to the supply circuit and consider the
effect that circuit overloading might have an overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when
addressing this concern.
5. Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted
equipment. Pay particular attention to supply connections other than direct connections
to the branch circuit (for example, the use of power strips).
XTP T HDMI Transmitter and XTP R HDMI Receiver • Reference Information
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Updating Firmware with Firmware Loader
To upload and update firmware for the XTP T HDMI and XTP R HDMI, download the new
firmware to a connected computer and upload the firmware with the Firmware Loader utility.
Downloading Extron Firmware Loader
Figure 19. Locating Firmware Loader Software on the Extron Website
2. From the left sidebar, click the Softwarelink.
3. Navigate to Firmware Loader.
4. Click the Downloadlink on the right that corresponds with the program.
5. Submit any required information to start the download.
Installing Firmware Loader
1. Once Firmware Loader has been downloaded, run the .exe file from the save location.
The installation wizard window opens.
2. Follow the instructions on the Installation Wizard screens to install the new firmware on
the computer. A Release Notes file, giving information on what has changed in the new
firmware version, and a set of instructions for updating the firmware are also loaded.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Reference Information
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Downloading Firmware
Figure 20. Downloading Firmware from the Extron Website
2. On the left sidebar, click the Firmwarelink.
3. Navigate to XTP T HDMI or XTP R HDMI.
4. Ensure the available firmware version is a later version than the current one on the
device.
NOTE: The firmware release notes are a PDF file that provides details about the
changes between different firmware versions. The file can be downloaded from the
same page as the firmware.
5. Click the Downloadlink to the right of the desired device.
6. Submit any required information to start the download. Note where the file is saved.
7. Open the executable (.exe) file.
8. Follow the instructions on the Installation Wizard screens to install the new firmware on
the computer. A Release Notes file, giving information on what has changed in the new
firmware version, and a set of instructions for updating the firmware are also loaded.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Reference Information
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Firmware with Firmware Loader
1. Connect the host device to the front panel USB port.
2. Open Firmware Loader and establish a connection between the computer and the
device. The Add Device... dialog box opens.
Figure 21. Add Device... Dialog Box
3. Select XTP T HDMI or XTP R HMDI from the Device Namedrop-down list.
4. Select the method of connection from the Connection Methoddrop-down list.
5. Depending on the connection method, additional options appear. Make the appropriate
selections for the current connection method.
6. Click Connect.
7. Click Browsein the New File Firmware (Optional) section.
8. On the Open dialog box, select the new firmware file, which has an .S19 extension, and
click Open.
ATTENTION: Valid firmware files must have the file extension .S19. A file with
any other extension is not a firmware upgrade for this device and could cause the
device to stop functioning.
9. Click Add. The Add Device... dialog box closes and the device and firmware are listed in
the Firmware Loader main window.
10. Click Beginto start the upload process.
11. Close Firmware Loader when the Remaining Timefield shows 00.00.00, the
Progresscolumn is 100%, and the Statusfield is completed.
XTP T HDMI Transmitter and XTP R HDMI Receiver • Reference Information
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of three years
from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty
workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is
returned within the warranty period, with proof of purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1230 South Lewis Street
Anaheim, CA 92805
U.S.A.
Japan:
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe and Africa:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Middle East:
Extron Asia Pte Ltd
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical
or mechanical abuse, abnormal operating conditions, or if modifications were made to the product that were not
authorized by Extron.
NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return
Authorization) number. This will begin the repair process.
USA: 714.491.1500 or 800.633.9876
Asia: 65.6383.4400
Europe: 31.33.453.4040
Japan: 81.3.3511.7655
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or damage
during shipment. Returned units must include the serial number and a description of the problem, as well as the
name of the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality,
performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct,
indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this warranty may
not apply to you.
Extron Headquarters
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
Extron Korea
Extron India
+1.800.633.9876 (Inside USA/Canada Only)
+800.3987.6673
(Inside Europe Only)
+65.6383.4400
+65.6383.4664 FAX
+81.3.3511.7655
+81.3.3511.7656 FAX
+86.21.3760.1568
+86.21.3760.1566 FAX
+971.4.299.1800
+971.4.299.1880 FAX
+82.2.3444.1571
+82.2.3444.1575 FAX
1800.3070.3777
Inside India Only
Extron USA - West
+1.714.491.1500
Extron USA - East
+1.919.850.1000
+31.33.453.4040
+91.80.3055.3777
+1.714.491.1517 FAX
+1.919.850.1001 FAX
+31.33.453.4050 FAX
+91.80.3055.3737 FAX
Download from Www.Somanuals.com. All Manuals Search And Download.
|