User’s Manual
PRELIMINARY
DAV101CM Series, DAS101CM Series
VGA Line Drivers and Audio Buffers
68-757-01 Rev. D
11 08
Download from Www.Somanuals.com. All Manuals Search And Download.
警告
安全须知 • 中文
这个符号提示用户该设备用户手册中
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必 须 使 用 有 地 线 的 供 电 系 统 供 电 。 第 三 条 线
（ 地 线 ） 是 安 全 设 施 ， 不 能 不 用 或 跳 过 。
拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后
或桌面电源的电源线，或任何接到市电系统的电源线。
电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴
露的危险电压，有触电危险。
维护 • 所有维修必须由认证的维修人员进行。 设备内部没
有用户可以更换的零件。为避免出现触电危险不要自己
试图打开设备盖子维修该设备。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解 所 有 安 全 和 使 用 说 明 。
保存说明书 • 用户应保存安全说明书以备将来使
用。
通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用与
厂家推荐的相同或相近型号的电池。 按照生产厂的建
议处理废弃电池。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备，以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
N
DAV101CM, DAS101CM • Safety and Compliances
Download from Www.Somanuals.com. All Manuals Search And Download.
DAV101CM, DAS101CM • Safety and Compliances
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start — DAV/DAS101CM Series
Installation and service must be performed by authorized
personnel only. These units must be installed in
accordance with national and local electrical codes.
C
To install the DAV101CM and DAS101CM modules, see the
appropriate section of this manual and follow these steps:
Step 1
Install an electrical box or wall bracket (if applicable) and cables.
Use cable clamps to hold cables in place for strain relief. Trim back
or insulate exposed cable shields with heat shrink to prevent short
Step 2
Attach cables to the rear panel. Ensure that power and output cables
have been fed through the wallbox/furniture and out the front of the
faceplate, frame, or panel. Connect modules to each other (if
applicable) and to the power supply, but do not apply power yet.
Connect output cables.
Balanced
Unbalanced
Stereo Output Wiring
Stereo Output Wiring
See the diagrams here
The channels of the
DAS101CM-3/-4
are reversed (R-L
instead of L-R)
relative to the
N
12VDC
0.1 A
12VDC
0.1 A
DAS101CM-1/-2/-5
Bottom View
DAS101CM-3/-4/-6
Right, ring, –
See caution.
Right, tip, +
Gnd, sleeve(s),
See caution.
Left, tip, +
Right, tip, +
DAS101CM-1/-2.
Ground, sleeve(s),
Left, ring, –
Left, tip, +
For unbalanced output, connect the sleeve to ground
C
(Gnd, ). Connecting the sleeve to a negative (-) terminal
_
will damage the audio output circuits.
The pin assignments of the DAS’s power input and power
loop-through ports are different from those of the
DAV’s power input.
C
TECHNICAL SUPPORT:
800.633.9876
714.491.1500
MADE IN USA
POWER IN
DAV101CM
(back view)
Double-check your
work against the wiring
12V
@0.3A
+
diagrams. Power wires must
be attached to the correct
terminals on each connector
DAS101CM
(back view)
or these products can be
damaged.
Power In
IN OUT
Loop Out to DAV101CM or CIA Interface
12 VDC, 1 A
DC Power
Adapter
DAV101CM, DAS101CM • Quick Start Guide
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide — DAV/DAS101CM, cont’d
Step 3
For wall/furniture or rack installations, attach the module(s) to a
CPM Series mini architectural adapter plate (MAAP) frame or to a
Step 4
Attach the front panel input cable(s).
Step 5
Verify correct cabling and connector wiring and test the system:
power on all the devices and monitor the audio/video output.
Each DAV module’s Power LED is lit while the unit receives power.
If needed, power off the devices, disconnect the
modules’ power supply, correct cabling or wiring
errors, then restore power.
Step 6
For a DAV101CM, set the sharpness/peaking
control using a small screwdriver, as shown at
Peaking
Step 7
G
N
I
K
A
E
P
Disconnect power from the module(s) and
R
E
W
VGA LINE DRIVE
O
R
P
other devices.
M
C
1
0
1
V
A
D
T
U
P
N
I
O
E
D
I
V
Step 8
For wall or furniture mounting, mount the
modular connector frame and module(s) to
the wall or furniture.
For device mounting, mount the module(s) to the device’s faceplate.
For rack mounting, mount the rack-mountable frame to the
equipment rack.
onto/against the mounting surface and secure it to wall, furniture,
device, or rack with the provided screws or bolts. Be careful not to
damage the cables.
Step 9
Restore power to the devices. You have completed the installation.
DAV101CM, DAS101CM • Quick Start Guide
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Features ........................................................................................ 1-2
Accessories ........................................................................................A-1
Cables ............................................................................................A-5
All trademarks mentioned in this manual are the properties of their respective owners.
68-757-01 D
11 08
DAV101CM, DAS101CM • Table of Contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents, cont’d
DAV101CM, DAS101CM • Table of Contents
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
About this Manual
This manual contains information about the Extron DAV101CM
VGA–QXGA line drivers and DAS101CM Series audio buffers
and on how to install them.
About the DAV/DAS101CM Series
The Extron DAV101CM Series modules are compact, one input,
one output, 400 MHz (-3 dB) bandwidth, VGA–QXGA line
drivers that amplify the signal from a laptop, desktop, or other
computer-video source. Each DAV101CM module buffers and
equalizes RGB and sync signals so they can be output on one set
of five BNC connectors (DAV101CM-3, -4, or -6) or one 15-pin
HD connector (DAV101CM-1, -2, or -5) and sent 150 feet or more
on Extron Mini HR cable.
The Extron DAS101CM Series modules are compact audio
buffers. Each module accepts one unbalanced audio input (on
either a 3.5 mm mini tip-ring-
sleeve jack [DAS101CM-1,
-2, or -5] or on a pair of
RCA connectors
[DAS101CM-3,
-4, or -6]) and
Projector
provides one
balanced or
unbalanced
audio output
(on a 3.5 mm,
5-pole captive
screw
Extron
DAV101CM
VGA Line Driver
VGA Line Drive
DAV101CM
Power
Extron
DAS101CM-1
Audio Buffer
Video Input
r
e
f
f
u
B
o
i
d
u
A
M
C
1
0
1
S
A
D
connector).
A typical
application
Extron
CPM101
Frame
Laptop
Features
Compact design and light weight — These modules can be
easily packed into a laptop case, portable projector case,
or technician’s tool kit.
DAV101CM, DAS101CM • Introduction
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Furniture- and rack-mountable design — The DAV/DAS101CM
modules can be mounted in a wall or
furniture using a connector module
frame and a junction box or a wall
bracket. They can also be mounted in
products with openings that
accommodate this style of connector
module or mounted to a CPM Series
rack-mountable frame.
Choice of colors — The modules are available with black, white,
or RAL9010 white faceplates.
DAV101CM Series
DAV101CM-3 (black)
DAV101CM-1 (black)
-2 (white)
-4 (white)
-6 RAL 9010)
-5 (RAL9010)
Adjustable peaking control — High frequency equalization
compensates for signal losses that occur in long cable
runs. The DAV101CM can drive signals for up to 150 feet
of Extron Mini HR cable or 250 feet of Extron SHR cable.
The variable sharpness control lets you select the best
peaking setting for the resolution and cable length.
Sync signal buffering with AGC — These modules provide
sync signal buffering and automatic gain control (AGC)
to restore sync signals to proper TTL levels for enhanced
stability and reliability over extended cable runs.
DAS101CM Series
DAS101CM-1 (black)
DAS101CM-3 (black)
-4 (white)
-2 (white)
-5 (RAL9010)
-6 (RAL9010)
Balanced or unbalanced audio output — Unbalanced, line
level stereo audio inputs can be output as balanced or
unbalanced stereo audio.
Power loop-through for a paired DAV101CM — A DAS101CM
can be mounted in a faceplate together with a DAV101CM
and share a single power supply so audio and computer
DAV101CM, DAS101CM • Introduction
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction, cont’d
video can be input, buffered, and driven from the same
location.
DAV101CM, DAS101CM • Introduction
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation
The DAV/DAS101CM modules can be attached to a CPM
mini architectural adapter plate (MAAP) mounting frame and
mounted in a wall or furniture using either a one-gang wall
box or a wall bracket. Alternatively they can be mounted in
the chassis of a device (such as a CIA Series interface) that
accommodates connector modules, or attached to a CPM Series
rack-mountable frame for mounting in a standard equipment rack.
Installing a Wall Box or Wall Bracket
For wall and furniture mounting installations, the installation
site must be deep enough for both the wall box (or the DAV/
DAS, if using a wall bracket) and the cables. The box should be
at least 2.5" (6.4 cm) deep. Install cables into the wall, furniture,
or conduits before installing a wall box or bracket.
1.
Place the wall box or mounting bracket against the
installation surface; mark the guidelines for the opening on
the wall or furniture.
2.
3.
Cut out the material from the marked area.
Insert the wall box/bracket to check the opening’s size and
fit. Enlarge or smooth the edges of the opening if needed.
4.
Feed cables through the wall box’s punch-out holes,
ground shields, and
secure cables with
Screw
cable clamps to
provide strain relief.
Braided
Shield
Metal
Wall
Box
Cable
Clamp
}
Grounding shields
To prevent
Install
Cable
W
Foil Shield
short circuits, the
outer foil shield can be cut
back to the point where the cable exits the cable clamp.
Connect both braided and foil shields to an equipment
ground at the other end of the cable. Insulate any
exposed shields with heat shrink
5.
Insert the wall box or wall bracket into the opening, and
attach it to the wall, stud, or furniture, leaving the front
edge flush with the outer wall or furniture surface.
To attach a wall box to wood, use four #8 or #10 screws or
10-penny nails. A minimum of 1/2 inch (1.3 cm) of screw
threads must penetrate the wood.
To attach a wall box to metal, use four #8 or #10 self-tapping
sheet metal screws or machine bolts with matching nuts.
DAV101CM, DAS101CM • Installation and Operation
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall Stud
Installation
Cable
Cable Clamp
Screws or Nails
Wall opening
is flush with
edge of box.
Attaching a wall box to a wall stud
7.
Mount the module(s) onto a mounting frame, then cable
and test the DAV/DAS before fastening it into the wall box
or bracket. The cables are inaccessible after installation.
Mounting the Module Into a Connector
Module Frame or Rack-mountable Frame
For wall, furniture, or rack mounting installations. DAV and
DAS modules must be attached to a faceplate, frame, or CPM
Series rack-mountable frame and cabled before being installed.
1.
2.
Insert the module into the faceplate's or frame’s opening.
Secure the module to the
faceplate or frame with the
provided machine
screws and nuts.
R
O
T
IT
A
N
L
N
O
U
IO
M
M
E
L
A
N
T
N
O
Z
S
I
O
I
R
O
T
O
P
I
H
T
R
U
P
E
T
W
U
O
PO
2
R
O
T
T
C
T
U
M
I
U
E
N
P
L
P
L
N
I
C
O
T
IN
A
E
O
S
L
T
U
P
T
U
T
U
P
N
O
I
1
N
R
O
O
T
E
D
U
T
I
I
P
L
V
I
N
I
O
R
M
E
T
A
U
P
C
O
M
L
G
IN
O
C
K
A
E
P
T
U
R
P
E
N
I
V
I
T
O
U
R
E
P
D
D
I
N
E
V
N
P
R
O
I
L
I
E
D
R
E
T
U
A
O
U
P
A
G
V
W
O
M
P
O
C
M
C
01
1
V
A
D
T
U
T
U
P
IN
N
I
E
ID
O
I
V
D
U
A
E
C
A
F
R
E
T
N
I
R
E
T
U
(4) #4 - 40
Screws
P
M
O
C
2
1
1
A
I
C
Attaching a DAS/DAV101CM to a device’s faceplate
DAV101CM, DAS101CM • Installation and Operation
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
PEAKING
R
WER
VGA LINE DRIVEPO
VIDEO INPUT
M
C
1
0
1
V
A
D
PEAKING
CPM112R-1
A/V Connector Panel
PEAKING
R
VGA LINE DRIVEPOR
WE
M
C
1
0
1
V
A
D
VIDEO INPUT
IVER
R
VGA LINE DR POWE
M
C
1
0
1
V
A
D
UT
VIDEO INP
PEAKING
INE DRIVER
L
POWE
R
VGA
M
C
1
0
1
V
A
D
INPUT
VIDEO
PEAKING
VGA LINE DRIVEPOR
WER
M
C
1
0
1
V
A
D
VIDEO INPUT
PEAKING
R
E
V
I
R
D
E
N
I
L
R
A
G
V
POWE
M
C
1
0
1
V
A
D
PUT
VIDEO IN
(4) #4 - 40
Screws
Attaching a DAS/DAV to a CPM rack-mountable frame
Rear Panel Features and Cabling
DAV101CM Series
DAV101CM-1, -2, -5
DAV101CM-3, -4, -6
TECHNICAL SUPPORT:
800.633.9876
714.491.1500
MADE IN USA
TECHNICAL SUPPORT:
800.633.9876
714.491.1500
MADE IN USA
POWER IN
POWER IN
12V
@0.3A
12V
@0.3A
+
+
1
1
2
3
+
Power input — Connect a 12 VDC
power supply directly to this two-pole
direct insertion captive screw
a
connector (see the diagram at right),
or
DAV101CM, DAS101CM • Installation and Operation
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
connect the power supply to a DAS101CM module’s 12 VDC
In port and loop the power through to the DAV101CM via the
Do not tin the stripped power supply leads before
installing the captive screw connector.
N
Correct polarity is important! The power wires must
be attached to the correct terminals or the module can
be damaged.
C
15-pin HD computer-video output (DAV101CM-1, -2, -5) —
Attach this connector to the display’s 15-pin HD input
connector.
b
c
BNC computer-video output (DAV101CM-3, -4, -6) — Attach
these five male BNC connectors to the display’s BNC input
connectors.
DAS101CM Series, and DAV-DAS interconnection
DAS101CM-1, -2, -5
Top View
DAS101CM-3, -4, -6
Top
View
12VDC
0.1 A
12VDC
0.1 A
1
2
3
1
2
3
DAS101CM-1, -2, -5 Rear View
DAS101CM-3, -4, -6 Rear View
12 VDC, 0.1 A In (power input) — Connect a 12VDC, 1 A power
supply to these two poles of the DAS’s 4-pole direct insertion
captive screw connector for power input.
a
b
Correct polarity is important! The power wires must
be attached to the correct terminals or the module can
be damaged.
C
12 VDC, 0.1 A Out (power loop-through for DAV101CM
modules) — This port allows power to be looped through to a
DAV101CM. See the wiring diagram on the next page.
DAV101CM, DAS101CM • Installation and Operation
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
The pin assignments of the DAS’s power input and
C
power loop-through ports are different from those of
the DAV modules’ power input. Double-check your
work against the wiring diagram. Power wires must
be attached to the correct terminals on each connector
or these products can be damaged.
TECHNICAL SUPPORT:
800.633.9876
714.491.1500
MADE IN USA
POWER IN
DAV101CM
(back view)
12V
@0.3A
+
DAS101CM
(back view)
Power In
IN OUT
Loop Out to DAV101CM or CIA Interface
12 VDC, 1 A
DC Power
Adapter
DAV-DAS power interconnection
Audio output — Wire this 5-pole, 3.5 mm, direct insertion
captive screw connector as shown below for either balanced or
unbalanced stereo audio output.
c
Balanced
Unbalanced
Stereo Output Wiring
Stereo Output Wiring
12VDC
0.1 A
12VDC
0.1 A
DAS101CM-1/-2/-5
Bottom View
DAS101CM-3/-4/-6
Right, ring, –
See caution.
Right, tip, +
Right, tip, +
Ground, sleeve(s),
Left, ring, –
Left, tip, +
Gnd, sleeve(s),
See caution.
Left, tip, +
The left and right channels of the DAS101CM-3/-4/-6 are
reversed (R-L instead of L-R) relative to the
DAS101CM-1/-2/-5, as shown above.
N
For unbalanced output, connect the sleeve to ground
C
(Gnd, ). Connecting the sleeve to a negative (-)
_
terminal will damage the audio output circuits.
DAV101CM, DAS101CM • Installation and Operation
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Features and Cabling
DAV101CM Series
1
1
DAV101CM VGA LINE DRIVER
DAV101CM VGA LINE DRIVER
POWER
POWER
VIDEO INPUT
VIDEO INPUT
DAV101CM-3/-4/-6
DAV101CM-1/-2/-5
2
2
Power LED — This indicator remains lit while the DAV is
receiving power.
a
b
Video Input — Connect a cable from the source computer to
the DAV via this 15-pin HD connector, which provides ID bit
termination on pins 4 and 11.
DAS101CM Series
DAS101CM-1, -2, -5
DAS101CM-3, -4, -6
DAS101CM AUDIO BUFFER
DAS101CM AUDIO BUFFER
1
2
3
Stereo audio input
(DAS101CM-1, -2, -5) — Connect an
Tip (L)
a
Ring (R)
unbalanced, line level stereo audio
source to this mini stereo jack using a
3.5 mm tip-ring-sleeve connector wired
as shown at right.
Sleeve (
)
3.5 mm Stereo Plug
(unbalanced)
,
Left and right audio inputs
(DAS101CM-3, -4, -6) — Connect an unbalanced, line level,
stereo audio source to these RCA (tip-ring) jacks.
bc
Wire the plugs as shown in the following diagram.
DAV101CM, DAS101CM • Installation and Operation
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Tip (Signal)
Right Channel
(Red Jacket)
Sleeve (Gnd )
Left Channel
(White Jacket)
Tip (+)
Sleeve (
)
RCA connector wiring for DAS101CM-3,-04 audio input
Adjusting Sharpness (DAV Modules)
The longer the cable being used, the
greater the signal loss. The DAV101CMs
have an adjustable sharpness/peaking
control that equalizes the video signal
to compensate for signal losses. The
DAV101CM can drive signals for up
to 150 feet of Extron mini HR cable or
Peaking
250 feet of Extron SHR cable.
While viewing the output image,
use a small screwdriver to rotate this
potentiometer to select the setting that
gives the clearest pictures.
G
N
I
K
A
E
P
R
E
W
VGA LINE DRIVER
O
P
M
C
1
0
1
V
A
D
T
U
P
N
I
O
E
D
I
V
Using a larger screwdriver
can break the potentiometer.
C
Mounting the Modules
Test the system. Adjust the sharpness (see "Adjusting
Sharpness") or disconnect the power and correct any cabling or
wiring errors before mounting the modules.
To avoid the risk of electrical shock, disconnect power
from the DAV or DAS module before mounting it.
C
For all installations, place the DAV’s or DAS’s faceplate (or the
mounting frame it is attached to) onto/against the mounting
surface and secure it with the provided screws or bolts. Be
careful not to damage the cables.
DAV101CM, DAS101CM • Installation and Operation
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall/furniture mounting
Mount the frame and module(s) to the wall or furniture, as
shown below.
G
N
I
K
A
E
P
r
e
w
o
VGA LINE DRIVER
P
M
C
1
0
1
V
A
D
t
u
p
n
I
o
e
id
V
r
e
f
f
u
B
o
i
d
u
A
M
C
1
0
1
S
A
D
(8) #4 - 40
Screws
DAV101CM, DAS101CM • Installation and Operation
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Device mounting
Mount the module(s) to the device’s faceplate, as shown below.
G
N
I
K
A
E
P
R
E
V
I
R
D
E
N
I
L
R
E
A
O
G
W
O
V
P
M
C
1
0
1
V
A
D
T
U
P
IN
E
D
I
V
(4) #4 - 40
Screws
Rack mounting
Mount the rack-mountable
frame to the equipment
rack as shown
below.
G
IN
K
A
E
P
ER
LINE DRIV
VGA
POWER
M
C
1
0
1
V
A
D
G
IN
K
VIDEO INPUT
A
E
P
ER
RIV
VGA LINE
D
POWER
M
C
1
0
1
V
A
D
VIDEO INPUT
G
IN
K
A
E
P
IVER
VGA LINE DR
POWER
M
C
1
0
1
V
A
D
UT
G
IN
K
VIDEO INP
A
E
P
VGA LINE DRIVER
POWER
M
C
1
0
1
V
A
D
UT
VIDEO INP
G
IN
K
A
E
P
R
VGA LINE DRIVER
POWE
M
C
1
0
1
V
A
D
INPUT
G
IN
VIDEO
K
A
E
P
VGA LINE DRIVER
POWER
M
C
1
0
1
V
A
D
VIDEO INPUT
Restore power to the devices.
You have completed the installation.
DAV101CM, DAS101CM • Installation and Operation
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, and Accessories
Specifications
Video— DAV101CM
Gain................................................. Unity
Bandwidth...................................... 400 MHz (-3 dB)
Video input— DAV101CM
Number/signal type..................... 1 VGA–QXGA RGBHV, RGBS, RGsB,
RsGsBs, or HDTV component video
Connectors ..................................... (1) 15-pin HD female
Nominal level ................................ 1 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of
component video
Minimum/maximum levels........ Analog: 0.3 V to 1.5 Vp-p with no offset
Impedance...................................... 75 ohms
Horizontal frequency.................... 15 kHz to 175 kHz
Vertical frequency.......................... 30 Hz to 150 Hz
Return loss...................................... <-40 dB @ 5 MHz
Video output— DAV101CM
Number/signal type..................... 1 VGA–QXGA RGBHV, RGBS, RGsB,
RsGsBs, or HDTV component video
Connectors
DAV101CM-1, -2, -5 .......... (1) 15-pin HD female on a 6" (15 cm)
pigtail
DAV101CM-3, -4, -6 .......... (1) set of 5 BNC female on 6.25" to 7"
(15.9 to 17.8 cm) pigtails
Nominal level ................................ 1 Vp-p for Y of component video
0.7 Vp-p for RGB and for R-Y and B-Y of
component video
Minimum/maximum levels........ Analog: 0.3 V to 1.5 Vp-p (follows input)
Impedance...................................... 75 ohms
Return loss...................................... <-40 dB @ 5 MHz
DC offset......................................... ±50 mV with input at 0 offset
Sync— DAV101CM
Input type....................................... RGBHV, RGBS, RGsB, RsGsBs, bi-level
and tri-level sync
Output type.................................... RGBHV, RGBS, RGsB, RsGsBs, bi-level
and tri-level sync (follows input)
Input level ...................................... 1.7 V to 5.0 Vp-p
Output level................................... TTL: 5.0 Vp-p, unterminated
DAV101CM, DAS101CM • Specifications, Part #s, Accessories
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Input impedance ........................... 510 ohms
Output impedance........................ <50 ohms
Max. propagation delay ............... <25 ns
Max. rise/fall time ........................ <5 ns
Polarity............................................ Positive or negative (follows input)
Audio— DAS101CM
Gain................................................. Unbalanced output: 0 dB;
Balanced output: +6 dB
Frequency response ...................... 20 Hz to 20 kHz, ±0.5 dB
THD + Noise.................................. <0.025% @ 1 kHz, <0.020% @ 20 kHz at
nominal level
S/N.................................................. >100 dB at maximum output (unweighted)
Stereo channel separation
DAS101CM-1, -2, -5........... >56 dB @ 20 Hz to 10 kHz
DAS101CM-3, -4, -6........... >75 dB @ 20 Hz to 10 kHz
Audio input— DAS101CM
Number/signal type..................... 1 stereo, unbalanced, line level
Connectors
DAS101CM-1, -2, -5........... (1) 3.5 mm mini audio jack (tip-ring-
sleeve), female
DAS101CM-3, -4, -6........... 1 pair of RCA (tip-ring) jacks, female
Impedance...................................... >10 kohms unbalanced, DC coupled
Nominal level ................................ -10 dBV (316 mVrms)
Maximum level.............................. +6 dBu, (balanced or unbalanced) at 1%
THD+N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
N
Audio output— DAS101CM
Number/signal type..................... 1 stereo, balanced/unbalanced
Connectors ..................................... (1) 3.5 mm direct insertion captive screw
connector, 5 pole
Impedance...................................... 50 ohms unbalanced, 100 ohms balanced
Nominal level ................................ -2 dBu (0.632 Vrms) for balanced output
Maximum level (Hi-Z) ................. >+15 dBu, balanced or unbalanced at 1%
THD+N
Maximum level (600 ohm)........... >+13 dBm, balanced or unbalanced at 1%
THD+N
DAV101CM, DAS101CM • Specifications, Part #s, Accessories
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, Accessories, cont’d
General
External power supply................. 100 VAC to 240 VAC, 50/60 Hz, 3 watts,
external, to a 12 VDC, 1 A power supply
(#70-055-01 included for the DAV101CM,
optional for the DAS101CM).
Power input requirements
DAV101CM ........................ 12 VDC, 0.3 A
DAS101CM......................... 12VDC, 0.1 A
Temperature/humidity................ Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +113 °F (0 to +45 °C) /
10% to 90%, noncondensing
Cooling ........................................... Convection, unvented
Rack mount.................................... Yes, with optional rack shelf and face
plates. Also wall or furniture mountable
with optional faceplates
Enclosure type ............................... Metal
Enclosure dimensions
DAV101CM
Faceplate..................... 1.4" H x 2.2" W x 0.1" D
(3.6 cm H x 5.6 cm W x 0.2 cm D)
Device ......................... 1.4" H x 1.4" W x 1.2" D
(3.6 cm H x 3.6 cm W x 3.0 cm D)
DAS101CM
Faceplate..................... 0.7" H x 2.2" W x 0.1" D
(1.8 cm H x 5.6 cm W x 0.2 cm D)
Device ......................... 0.7" H x 1.4" W x 1.3" D
(1.8 cm H x 3.6 cm W x 3.3 cm D)
Product weight .............................. 0.2 lbs (0.1 kg)
Shipping weight ............................ 1 lb (1 kg)
Regulatory compliance
Safety................................... CE, ETL (UL1950)
EMI/EMC .......................... CE, FCC Class A
MTBF............................................... 30,000 hours
Warranty......................................... 3 years parts and labor
All nominal levels are at 10%.
N
N
Specifications are subject to change without notice.
DAV101CM, DAS101CM • Specifications, Part #s, Accessories
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Included Parts
These items are included in each order for a DAS/DAV101CM:
Included parts
Replacement
part number
DAV101CM-1, -2, -5 (15-pin HD output
[black, white, RAL9010 white])
60-612-11, -21,
-51
DAV101CM-3, -4, -6 (BNC output
[black, white, RAL9010 white])
60-613-11, -21,
-51
DAS101CM-1, -2, -5 (mini jack input
[black, white, RAL9010 white])
60-610-11, -21,
-51
DAS101CM-3, -4, -6 (RCA input
[black, white, RAL9010 white])
60-611-11, -21,
-51
12VDC, 1 A external power supply
(DAV only)
70-055-01
3/32" hex wrench
4-40 hex socket cap screws
(4 per DAV, 2 per DAS)
User’s manual
Accessories
Accessories
Part number
12 VDC, 1 A external power supply
(optional for DAS models)
70-055-01
CPM112R 1U high, full rack width frame
60-584-12
60-584-15
CPM 133 1U high, one-third rack width
frame
CPM120 connector frame
60-588-11
CIA111, CIA112, CIA116 interfaces
same as model
name
Cables
Male-to-female VGA cables w/audio Part number
VGA 3' HRA, VGA 6' HRA
VGA 12' HRA, VGA 25' HRA
VGA 35' HRA, VGA 50' HRA
26-491-01, -02
26-491-03, -04
26-491-07, -08
DAV101CM, DAS101CM • Specifications, Part #s, Accessories
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, and Accessories
DAV101CM, DAS101CM • Specifications, Part #s, Accessories
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron USA
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Japan:
Extron Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
China:
Europe, Africa, and the Middle East:
Extron Europe
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
Asia:
Middle East:
Extron Asia
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
135 Joo Seng Road #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or non-
Extron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|