Heavy Duty Upright
Vacuum Cleaner
Ownerʼs Guide
HD4570 Series
Index
Important Safeguards.............2
Service Information ................4
Assembly.............................5-6
Use.........................................7
Thermal Cut Off............... 4 & 7
Accessories............................8
Brush Roll...............................9
Brush Roll Belt...................9-10
Dust Bag..........................10-11
Hose Blockage ................12-13
Filters....................................14
HEPA Filter ...........................14
Light Bulb .............................15
Problem Solving ...................16
Warranty...............................17
Repair Parts List..............18-27
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSEILS DE SÉCURITÉ
Lors de lʼutilisation dʼun appareil électrique, quelques précautions élémentaires doivent être observées, incluant les suivantes:
LISEZ TOUTES LES INSTRUCTIONS AVANT DʼUTILISER VOTRE ASPIRATEUR.
AVERTISSEMENT
Pour réduire le risque de feu, de choc électrique, ou de blessure:
• Ne pas utiliser à lʼextérieur ou sur des surfaces mouillées.
• Cet appareil est muni dʼun double-isolement. Utilisez uniquement des pièces de rechange identiques. Voir les instructions pour
lʼentretien dʼappareils à double-isolement.
• Fermez le commutateur et débranchez lʼappareil lorsque vous ne lʼutilisez pas ou avant le nettoyage ou lʼentretien.
• Ne permettez pas quʼil soit utilisé comme jouet. Une attention particulière est nécessaire lorsque utilisé par ou prés dʼun
enfant.
• Suivez les recommandations dʼutilisation de ce manuel. Utilisez uniquement les accessoires recommandés par le fabriquant.
• Ne pas utiliser si le cordon ou la fiche sont endommagés. Si lʼaspirateur ne fonctionne pas comme il le devrait, sʼil a été échappé,
sʼil est endommagé, sʼil a été laissé à lʼextérieur ou échappé dans lʼeau, retournez-le à un centre de service avant dʼutiliser.
• Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon en guise de poignée. Ne pas fermer une porte sur le
cordon ou tirer le cordon sur des coins ou bordures pointus. Ne pas circuler sur le cordon avec lʼaspirateur. Tenir le cordon à
distance des surfaces chauffantes.
• Ne pas utiliser des rallonges ou des prises qui nʼont pas de capacité suffisante pour transporter le courant.
• Fermer tous les contrôles avant de débrancher.
• Ne pas débrancher en tirant sur le cordon. Pour débrancher, tenez la fiche et non le cordon.
• Ne pas manipuler la fiche ou lʼaspirateur avec les mains mouillées.
• Ne pas rien insérer dans les ouvertures. Ne pas utiliser si des ouvertures sont bloquées; assurez-vous quʼelles soient dégagées
de poussière, mousse, cheveux ou toute autre chose qui pourrait réduire le passage de lʼair.
• Cet aspirateur créé de la succion et contient un rouleau-brosse tournant. Tenir les parties mobiles et les ouvertures loin des
cheveux, du linge, des doigts et de toute partie du corps.
• Nepasmettrelʼaspirateursurlesmeublesousurlesescalierscarlerouleau-brossepeutfairedesdommages. Placerlʼaspirateur
sur le plancher avec le manche en entreposage position temps que les accessoires sont en usage.
• Ne pas ramasser des objets qui brûlent ou fument comme les cigarettes, allumettes ou cendres chaudes.
• Nʼutilisez pas sans le sac de poussière en place.
• Les poulies du courroie peuvent devenir chaudes pendant lʼutilisation normale. Pour prévenir des brûlures, évitez de touché la
poulie du courroie lorsque vous réparez la courroie.
• Portez une attention particulière lorsque vous nettoyez les escaliers.
• Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de lʼessence: Ne pas utiliser dans les endroits
où ces liquides pourraient être présents.
• Entreposez votre aspirateur à lʼintérieur dans un endroit propre et sec.
• Maintenez un bon éclairage à lʼendroit où vous travaillez.
• Débrancher les appareils électrique avant de les balayer.
CONSERVEZ CES INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
3
SERVICING OF DOUBLE-INSULATED APPLIANCES
A double-insulated appliance is marked with one or more of the following: The words “DOUBLE INSULATION” or
“DOUBLE INSULATED” or the double insulation symbol (square within a square).
In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means
is provided on a double-insulated appliance, nor should a means for grounding be added to the appliance. Servicing
a double-insulated appliance requires extreme care and knowledge of the system, and should be done only by
qualified service personnel. Replacement parts for a double-insulated appliance must be identical to the parts they
replace.
To reduce the risk of electric shock, this appliance has a polarized plug (one blade wider than the other). This plug will fit
in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
Afin de réduire le risque de choc électrique, cet appareil est muni dʼune fiche polarisée (une des lames est plus large).
Cette fiche ne peut être insérée dans une prise polarisée que dʼune seule façon. Si la fiche ne peut être insérée dans la
prise, retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire installer une prise adéquate par un
électricien qualifié. Ne pas modifier la fiche.
GENERAL INFORMATION
The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or sharp objects with the cleaner to prevent
bag tears, hose clogs, and possible motor damage.
Service Information
The instructions in this booklet serve as a guide to routine maintenance. For additional service information telephone our toll
free number for the nearest Eureka Authorized Warranty Station. You should know the model, type and serial numbers
when you call:
USA: 1-800-282-2886
Mexico: 5670-6169
Canada: 1-800-282-2886
If you prefer, you can write to Electrolux Home Care Products North America, Service Division, 807 North Main Street,
Bloomington, Illinois 61701, USA. In Canada write to Electrolux Home Care Products Canada, 866 Langs Drive, Cambridge,
Ontario N3H 2N7. Refer to The Eureka Limited Warranty for complete service information.
DO NOT OIL the motor or the brush roll at any time. The bearings are permanently lubricated and sealed.
Rating Plate
The model, type, and serial numbers are indicated on the
rating plate located on the back of the cleaner. For prompt
and complete service information, always refer to these
numbers when inquiring about service.
MODEL
VOLTS
TYPE
SERIAL NO.
HERTZ
AMPS.
SERVICE INFORMATION: 1-800-282-2886
Model & Type__________________________
Serial No. _____________________________
ELECTROLUX HOME CARE PRODUCTS
BLOOMINGTON, ILLINOIS 61701
Thermal Cut Off
This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner suddenly
shuts off, push power switch off and unplug the cleaner. Check the cleaner for a possible source of overheating such as a full
bag, a blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes before attempting
to use the cleaner. After the 30 minute period, plug the cleaner back in and turn on the switch. If the cleaner still does not
run, then take it to a Eureka Authorized Service Center for repair.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ASSEMBLE
CAUTION: Moving parts, make sure on/off switch is in off position before plugging in.
CAUTION: Assemble the cleaner before using.
NOTE: Features may vary by model yet all parts assemble the same.
Step A Attach Handle
CAUTION: Do not catch cord under handle.
Step B Attach Hose
2
Tab
3
Ledge
1
Groove
2
1
Groove
Electrical
Cord
3
1. Before placing the front cover on the unit, install the
hose.
1. From rear of cleaner, align handle with groove and
slide onto cleaner. If necessary, use thumb and finger
pressure to slide handle into position.
2. Locate the tab on the hose adapter (shortest end).
3. Look at the opening on the top of the cleaner and locate
the ledge. The tab on the hose adapter will be under the
ledge in the opening when hose is installed properly.
2. Once handle is in place, check that the electrical cord
is not pinched between the unit and the handle. Push
excess cord back into the hole provided in the back of
the handle.
4. Push hose adapter into opening and rotate until tab is
under ledge. If installed properly, the hose cannot be
lifted out of the hose opening.
3. Attach handle with two 5/8 inch screws in the assembly
®
packet. Use a Phillips head screwdriver.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Step C Check Disposable Dust Bag
Step D Store Hose and Accessories
1
Hose
Adapter
Dusting
Brush
Upholstery
Tool
Paper Bag Collar
1. Check to be sure the paper bag collar is secure with
the hose adapter inside the paper bag collar.
Crevice
Tool
Carrying
Handle
Telescoping
Wand
Hose
Retainer
Step E Store Electrical Cord
2. Replace front bag cover. Place the tabs on the bag
cover in the slots at the bottom of the bag compartment.
Using both hands, one on each side, press the bag
cover firmly back against unit until latch clicks shut.
1
Cord
Hook
1. Wind the cord around the two cord hooks on the left side
of cleaner. On some models the upper cord hook turns
to release the cord. Turn the hook up to store the cord.
2. Secure the plug to the cord to prevent unwinding.
1
Cord
Hook
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE
The upright vacuum cleaner design allows use on multiple types of
carpeting and on upholstery or bare floors with attachments. When
using the attachment tools, place the handle in the upright
position. Do not place cleaner on furniture or steps as the brush
roll may cause damage.
4
ON/OFF
1. Adjust cleaner height setting knob to lowest position for maximum
cleaning. Adjust to a higher setting to make pushing easier. For
easy adjustments, tilt the cleaner back to move the knob.
2. Plug electrical cord into outlet.
3. Step on handle release. Pull handle back to a comfortable
position.
2
4. Push On (-) or Off (0) power switch.
Store or
Use Attachments
Use
Handle
Release
3
Clean
Under
Handle
Release
3
Cleaner Height Setting
WARNING: Avoid injury. Keep loose
clothing, hair, fingers, and
all other parts of body away
from any moving part (such
astherevolvingbrush). Turn
off the switch and unplug
the cleaner before changing
1
THERMAL CUT OFF
the cleaner height setting.
This cleaner has a special thermostat that protects the cleaner
in case of motor overheating. If the cleaner suddenly turns off,
follow this procedure:
The front of the cleaner has an adjustment that
raises or lowers the cleaner base to match the type
of carpet. With the cleaner cord unplugged, set the
adjustment to lowest setting for maximum cleaning.
If the cleaner is difficult to push, move adjustment
to next highest setting until cleaner is comfortable
to push. The brush roll must reach the carpet for
effective cleaning.
1. Push power switch off.
2. Unplug cleaner.
3. Check for source of overheating problem (i.e. full bag, clogged
hose or clogged filter).
4. If a full bag, clogged hose or clogged filter is found, replace the
bag, unclog the hose or replace the filters.
Make each adjustment with cleaner switch off
and cord disconnected from outlet. For ease
in moving the adjustment knob, place handle in
operating position and tilt cleaner back to remove
weight from front wheels.
5. Wait at least 30 minutes before attempting to reuse the cleaner.
6. After 30 minute cool down period, plug the cleaner in and push
the power switch on. The cleaner should turn on.
7. If the cleaner still does not operate, take it to any EurekaAuthorized
Service Center for repair.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
How To Use Accessories
Crevice Tool cleans corners, baseboards, between
cushions, sliding door tracks.
NOTE: Do not place cleaner on furniture or
steps as the brush roll may cause
damage. Place cleaner on floor with the
handle in storage position while using
accessories.
1. Remove hose from rear of cleaner.
2. Place desired accessory onto end of hose or wand.
Dusting Brush is for furniture, blinds, books, lamp shades,
shelves.
Upholstery Nozzle is for curtains, draperies, cushions,
fabrics.
Telescoping Wand
To adjust the length of the telescoping wand, hold the wand
adjustment collar in one hand while pulling or pushing the
wand with the other hand until you have the desired length.
Wand Adjustment Collar
8
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO MAINTAIN
The instructions in this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls, check the bag,
belt, and brush roll often.
Brush Roll
The brush roll turns as it sweeps and combs the carpet nap. Remove hair and threads from the brush roll so it continues
brushing the carpet. To maintain the most efficient cleaning, the bristles must touch the carpet. To test the bristle length, hold
a ruler against the underneath side of the cleaner. If the bristles no longer touch the ruler, replace the brush roll.
Brush Roll Belt
The brush roll belt turns the brush roll to agitate, sweep, and comb the carpet nap. Check the belt regularly to be sure it is
in good condition. Replace the belt if it stretches, cracks or loses tension. Cut away any hair or threads wound around the
brush roll or the belt pulley because the buildup could cause the belt to rotate unevenly.
How To Replace Brush Roll Belt
NOTE: Turn off the switch and unplug the electrical cord before replacing belt. Belt pulleys can become hot
during normal use. To prevent injury, avoid touching the motor pulley when checking the belt.
4
Motor
Pulley
Belt
2
1
Brush
Roll
2
3
3. Lift left end of brush roll.
4. Remove and discard belt.
1. Lower handle to floor to change belt.
2. Loosen the two fasteners located on the top of the hood
and lift upward. These fasteners need only a quarter
turn to lock or unlock the hood.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
5
8
5. Place new belt around motor pulley.
8. Pull right side of brush roll to stretch belt. Secure right
end cap into base.
7
6
9
Left Side View
9. Rotate brush roll to seat belt.
6. Place belt around brush roll.
10. Replace the hood. Make sure hood front is behind
furniture guard. Hood should seat onto self-locating
fastener tabs.
7. Align left end cap with square in base. Push end cap
into place; see left side view.
11. Turn fasteners 1/4 turn to lock.
Disposable Dust Bag and Filters
The disposable dust bag plays a very important role in
the efficiency of a vacuum cleaner. The purpose of the
paper bag is to trap dirt. As the bag traps dirt, it must also
be porous enough to allow air to pass on through. If the
paper bag becomes clogged, no air can pass through the
cleaner and no cleaning can take place regardless of how
powerful the unit. Change the dust bag and check the
filters frequently. Some fine particles can restrict airflow
very quickly and will decrease performance even before
the bag appears to be full.
When vacuuming carpet fresheners or cleaners, powder,
plaster dust, or similar fine substances, the bag and filters
may require more frequent maintenance.
Use GENUINE EUREKA replacement belt, 54312.
Look for the
product symbol.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
How To Replace Bags–Style AA
NOTE: Turn off the switch and unplug the electrical cord before changing dust bag. Never operate the vacuum
cleaner without the dust bag or the filter.
To Remove Bag:
Front Cover
Latch
B
A
Front
Cover
A. Remove front cover by pulling out on the front
cover latch and lifting the front cover upward
and out.
B. Remove left side of bag collar from bag collar
retainer. Grasp bag collar; pull down slightly
and out to remove bag.
To Replace New Bag:
F
C. Fold sides on new paper bag below bag
collar.
D. Align bag collar hole and notch with hose
tube.
E
E. Place rear of bag collar on ledges. Push
back and rotate upward until firmly in
place. Make sure collar snaps into position
and hose tube is securely inserted into bag
collar hole.
E
D
C
F. Tuck bag into bottom and along sides.
Bag
Collar
Bag
Side
G. Align front cover tabs and close cover.
Make sure paper bag is not caught under
the front cover.
We recommend using only Genuine Eureka
Standard AA Bags, part number 58236.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Check and Clear Hose Blockages
Low suction or poor pickup may be due to a blockage in the vacuum cleaner.
1. Remove hose and check suction at end of hose - if little or
no suction, check disposable dust bag. Change if needed.
If no improvement proceed to Step 2.
NOTE: Turn off the switch and unplug the electrical
cord before clearing hose.
2. Remove the front bag cover. To remove hose adapter from
opening, twist hose adapter clockwise and lift upward.
Once the hose is removed from the cleaner check for any
obstructions that may be in the hose. Any obstructions can
be removed by using a blunt instrument to clear the hose.
Flexing the hose may help loosen the clog.
1
3. Reinstall the hose after clearing the clog. Make sure the
hose is inserted into the top of the vacuum cleaner.
NOTE: If no improvement in performance on carpet,
proceed to following page.
1. Remove hose and check suction at end of
hose.
Hose Adapter
4
3
2. Remove front bag cover.
3. Remove hose adapter by twisting clockwise and lifting
upward. Check hose for blockages.
4. Reinstall the hose and replace front bag cover.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Check and Clear Blockages in Base
2. Remove the hood by loosening the two fasteners
located on the top of the hood and lifting upward. These
fasteners need only a quarter turn to lock or unlock the
hood. (See padlock graphics on the hood.)
1. Remove the attachment hose from the lower hose
retainer and look into the hose retainer for any
obstructions. Proceed to Step 2 to check for any other
blockages.
Upright Position
Operating Position
Lowest Position
for cleaning
under furniture
Handle
Release
3. Step on the handle release and lower the handle all the
way to the floor.
4. Check for blockages in the brush roll area and remove
any obstructions found there. The base hose can be
cleared of any blockage by using a blunt instrument.
5. After the blockage is removed, replace the hood and
tighten the two hood screws (see Figure 2). Raise the
handle to the upright position (see Figure 3) and replace
the hose into the lower hose retainer.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Motor Filter
Check the motor filter with each disposable dust
bag change. Clean or replace as needed.
3
To Clean Motor Filter
Back Ledge
1. Remove filter from inside bag compartment,
lower left side.
2. Shake filter or vacuum with another cleaner to
remove excess dust.
3
Filter Retainer
3. Reinstall filter. Slide under back ledge and
filter retainer. Install with colored/smooth side
down.
and
3
1
HEPA Filter
Check the HEPA filter with each disposable dust bag
change. Replace twice a year or as needed.
Latch
To remove HEPA Filter
1. Push down latch and pull HEPA filter back.
2. Then lift filter up and remove.
To replace HEPA Filter
1. Place bottom tabs of filter into slots.
2. Rotate filter toward cleaner.
3. Push upward on the latch to secure into place.
Obtain replacement filters from a local dealer or order
them from The Eureka Company, Bloomington, IL.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
How To Change Light Bulb (only for models with a headlight)
NOTE: Turn off the power switch and
disconnect the electrical cord
before changing light bulb.
1. Lower handle to remove two screws from lens cover.
2. Pull lens cover from cleaner.
1
3. Support socket with one hand and push light bulb into
socket; turn to release.
4. Place new light bulb into socket; turn to secure.
5. Push light bulb and socket back so bulb will not touch
lens cover.
6. Replace lens cover.
4
7. Secure with two screws.
2
5
3
Use 15 watt replacement light bulb, part
number 48815.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM SOLVING
NOTE: Turn off the switch and unplug the electrical cord before servicing.
PROBLEM
CAUSE
SOLUTION
Motor will not start.
Electric Plug
Push plug securely into outlet.
Try another outlet.
Check circuit breaker.
✓
Motor suddenly stops.
Thermal Cut Off
Refer to page 7.
✓
✓
Does not clean the carpet
or floor.
Disposable Dust Bag
and Filter(s)
Change the bag and clean or replace the
filter(s). Hint: If picking up fine dust, the bag
may not look full but a fine substance tends
to reduce suction when it blocks the airflow
through the paper bag and filter(s).
Dust Bag
Belt
Be sure hose adapter inserts into paper bag.
Replace a cut, loose or out of shape belt.
✓
✓
✓
Belt Cover
Snap the belt cover inside the hood if it comes
loose.
✓
✓
Brush Roll
Hose
Clean hair and thread from bristles and end
cap area. Replace brush roll if bristles are worn.
Remove any clogs from the hose that restrict
the airflow. Check short hose in the base and
long hose. Refer to page 12 & 13.
No suction at the end of
the hose.
Hose Adapter
Hose adapter has to seat inside the dust bag.
✓
✓
Disposable Dust Bag
and Filter(s)
Change the bag and clean or replace the
filter(s). Hint: If picking up fine dust, the bag may
not look full, but a fine substance tends to reduce
suction when it blocks the airflow through the
paper bag and filter(s).
Hose
Remove any clogs from the hose that restrict the
airflow. Check short hose in the base and long
hose. Refer to page 12 & 13.
✓
Headlight not working.
Light Bulb
Brush Roll
Replace light bulb.
✓
✓
Noise from the brush roll
area.
Remove hood and clean debris or items
from the brush roll area.
Belt
Replace a cut, loose or out of shape belt.
✓
✓
Cleaner is hard to push.
Cleaner Height Setting
Put handle in operating position. Tilt the
cleaner back to raise the front wheels off floor.
Then turn the knob to a higher setting.
Belt
Replace a cut, loose or out of shape belt.
✓
✓
Cleaner height knob will
not turn.
Cleaner Height
Setting
Hint: Put handle in operating position. Tilt the
cleaner back to raise the front wheels off floor.
Then turn the knob.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
THE EUREKA® HD
2 YEAR LIMITED WARRANTY
WHAT THIS WARRANTY COVERS
Your Eureka HD cleaner is warranted to be free from all defects in material and workmanship in normal use FOR
A PERIOD OF TWO YEARS. The warranty is granted only to the original purchaser of the cleaner. The warranty is
subject to the following provisions.
WHAT THIS WARRANTY DOES NOT COVER
• Parts of the cleaner that require replacement under normal use, such as bumpers, bags, bristle strips, belts, light
bulbs, hoses, and impellers.
• Damages or malfunctions caused by negligence, abuse, or use not in accordance with the Ownerʼs Guide.
• Defects or damages caused by unauthorized service or the use of other than Genuine Eureka parts.
WHAT THE EUREKA COMPANY WILL DO
The Eureka Company will, at its option, repair or replace a defective cleaner or cleaner part that is covered by this
warranty. As a matter of warranty policy, the Eureka Company will not refund the consumerʼs purchase price.
WARRANTY REGISTRATION
Please fill out and return the warranty registration card accompanying your cleaner.
OBTAINING WARRANTY SERVICE
To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any
Eureka Authorized Warranty Station. You will find the nearest location in the Yellow Pages under “Vacuum Cleaners–
Service and Repair”. Be certain that the Warranty Station is “Eureka Authorized”.
For the location of the nearest Eureka Authorized Warranty Station or for service information, telephone toll free:
USA: 1-800-282-2886
Mexico: 5670-6169
Canada: 1-800-282-2886
If you prefer, you can write to:
USA:
CANADA:
Electrolux Home Care Products
Canada
866 Langs Drive
Cambridge, Ontario N3H 2N7
Electrolux Home Care Products
North America
Service Division
807 North Main Street
Bloomington, IL 61701
If it is necessary to ship the cleaner outside your community to obtain warranty repair, you must pay the shipping
charges to the EurekaAuthorized Warranty Station. Return shipping charges will be paid by the Warranty Station. When
returning parts for repair, please include the model, type, and serial numbers from the data plate on the cleaner.
FURTHER LIMITATIONS AND EXCLUSIONS
Any warranty that may be implied in connection with your purchase or use of the cleaner, including any warranty of
MERCHANTABILITY or any warranty for FITNESS FOR A PARTICULAR PURPOSE is limited to the duration of this
warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not
apply to you.
Your relief for the breach of this warranty is limited to the relief expressly provided above. IN NO EVENT SHALL
EUREKA BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES THAT YOU MAY INCUR IN
CONNECTION WITH YOUR PURCHASE OR USE OF THE CLEANER. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary by State.
ELECTROLUX HOME CARE PRODUCTS NORTH AMERICA
Bloomington, Illinois 61701
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS LIST
HD4570A
Eureka Heavy Duty
THE EUREKA COMPANY
BLOOMINGTON, IL 61701
4/7/04
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HD4570A
1.
2.
3.
60940
60249-8
60941
58506-3
FASTENER - pkg of 10
HOOD ASSEMBLY
RETAINER - pkg of 10
GASKET
4.
5.
6.
27462E-288N
38590A
HEIGHT ADJUSTMENT KNOB
REAR AXLE
7.
8.
9.
60939
60938-7
54376-2
57569
15591A-288N
62352-1
53197-1
27468D-288N
27467A-288N
60133
53197-1
38420-2
38479-4
28243A-316N
54432-2
72117-288N
72113-1
54943
14993C-119N
71551
39173A-119N
61120A
RECEPTACLE - pkg of 10
BASE ASSEMBLY*
BELT CAP ASSEMBLY**
GASKET - BELT CAP
FURNITURE GUARD
BRUSH ROLL ASSEMBLY
SCREW - pkg of 10
HOSE CUFF
HANDLE RELEASE
COMPRESSION SPRING - pkg of 5
SCREW - pkg of 10
CLAMP
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
COMPRESSION HOSE
BASE ADAPTER
RETAINING RING - pkg of 10
REAR WHEEL
AXLE BUSHING
SPRING - pkg of 10
WHEEL CARRIAGE
FRONT AXLE
FRONT WHEEL
BELT - pkg of 2
INCLUDES ITEMS 5, 6, 11, 20, 21, 22, 23, 24, 25, 26 & 27
INCLUDES ITEM 10
*
**
20
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
HD4570A
1.
2.
58505SV
39268
BAG COVER GASKET
LATCH SPRING
3.
4.
5.
6.
7.
8.
9.
28256-288N
60937-7
38613
53197-1
60942-7
15407-313N
60068-2
48815
BAG COVER LATCH
BAG COVER ASSEMBLY*
BAG GASKET - BOTTOM
SCREW - pkg of 10
MOTOR COVER ASSEMBLY**
LENS
SCREW - pkg of 10
HEADLIGHT
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
38611-1
59362B
59361A
59137
60943-4
70840
46713-5
39252-3
70133-119N
53197-1
15443B-119N
28290-333N
60944-2
60285B
LIGHT SOCKET
TUBE - 7"
ADAPTER TUBE
MOTOR EXHAUST GASKET
HEPA MOTOR ASSEMBLY***
GROMMET
CABLE TIE
THERMOSTAT ASSEMBLY
TOOL CADDY BUSHING
SCREW - pkg of 10
TOOL CADDY
FLANGE RETAINER
REAR HOUSING
HEPA FILTER
SPLICE - pkg of 5
NUT - pkg of 10
MOTOR FILTER - pkg of 2
AIR DUCT GRILLE
AIR DUCT GASKET
AIR DUCT
MOTOR INTAKE GASKET
MOTOR INTAKE FLANGE
60192-1
60613
61333
28425
59297SV
15408B-119N
27171A
39023
INCLUDES ITEMS 1, 2, 3 & 5
INCLUDES ITEMS 8 & 9
INCLUDES ITEMS 14 & 16
*
**
***
22
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
HD4570A
1.
2.
3.
15597-288N
02349A-288N
39455-1
GRIP (RH)
SWITCH HOUSING (RH)
ROCKER SWITCH
4.
15580
HANDLE
5.
6.
7.
8.
53238-39
59741-316N
15533-366N
39585-11
60192-1
28011-2
15596-288N
53197-1
53197-1
15581-119N
53197-1
15534A-366N
53197-1
39513-288N
28316-288N
60945
SCREW - pkg of 10
WIRING SHIELD
FRONT HANDLE HOUSING
SUPPLY CORD ASSEMBLY
WIRE SPLICE - pkg of 5
UPPER CORD ASSEMBLY
GRIP (LH)
SCREW - pkg of 10
SCREW - pkg of 10
HANDLE COVER
SCREW - pkg of 10
REAR HANDLE HOUSING
SCREW - pkg of 10
SWITCH HOUSING (LH)
CORD RETAINER
SPRING - pkg of 10
WASHER - pkg of 10
SCREW - pkg of 10
HANDLE ASSEMBLY COMPLETE*
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
60946
53238-18
15605A-8
INCLUDES ITEMS 1 THRU 22
*
24
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
HD4570A
1.
2.
3.
4.
5.
6.
7.
8.
9.
60920-2
28375-119N
39514A
HOSE ASSEMBLY*
HOSE ADAPTER
TELESCOPIC WAND ASSEMBLY
DISPOSABLE BAG (style AA FILTERAIRE) - pkg of 3
HOSE COUPLING
CREVICE TOOL
UPHOLSTERY NOZZLE ASSEMBLY
DUSTING BRUSH
HOSE STRAP
HOOK PLATE
58236A
37057B-3
27237-3
38284-3
60290-1
39231-2
39152A-333N
70124A
10.
11.
12.
HARDWARE PACKAGE
OWNER’S GUIDE
74339
INCLUDES ITEMS 2 & 5
*
26
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly Items in This Carton
1 hardware
package (2 screws)
1 dusting brush
1 crevice tool
1 hose adapter w/hose
1 telescoping wand
1 cleaner connected
to handle by cord
1 upholstery brush
1 front cover
Thank you for selecting a Eureka cleaner.
Donʼt Forget to Use Genuine Eureka Bags and Belts
Caution: Damages caused by the use of non-
genuine Eureka bags are not covered by
The Eureka Heavy Duty Limited Warranty.
©2004 Electrolux Home Care Products, Ltd.
Printed in U.S.A.
Part No. 74339 (3/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
|