Mode d’emploi
Manuale d’uso
Manual del usuario
Thank you, and congratulations on your choice of the UM-1EX USB MIDI Interface.
2B0e1afore using this unit, carefully read the sections entitled: “USING THE UNIT
SAFELY” and “IMPORTANT NOTES” (p. 2; p. 4). These sections provide
important information concerning the proper operation of the unit. Additionally,
in order to feel assured that you have gained a good grasp of every feature
provided by your new unit, Owner’s manual should be read in its entirety. The
manual should be saved and kept on hand as a convenient reference.
202
Copyright © 2005 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form
without the written permission of ROLAND CORPORATION.
Download from Www.Somanuals.com. All Manuals Search And Download.
007
023
•
Make sure you always have the unit placed
so it is level and sure to remain stable.
Never place it on stands that could wobble,
or on inclined surfaces.
•
DO NOT play a CD-ROM disc on a conven-
tional audio CD player. The resulting
sound may be of a level that could cause
permanent hearing loss. Damage to
speakers or other system components may
result.
...............................................................................................
011
•
Do not allow any objects (e.g., flammable
material, coins, pins); or liquids of any kind
(water, soft drinks, etc.) to penetrate the
unit.
...............................................................................................
104
...............................................................................................
•
Try to prevent cords and cables from
becoming entangled. Also, all cords and
cables should be placed so they are out of
the reach of children.
012d (Modified)
•
Immediately disconnect the USB cable, and
request servicing by your retailer, the
nearest Roland Service Center, or an autho-
rized Roland distributor, as listed on the
“Information” page when:
...............................................................................................
106
•
Never climb on top of, nor place heavy
objects on the unit.
•
•
If smoke or unusual odor occurs
Objects have fallen into, or liquid has
been spilled onto the unit; or
...............................................................................................
108c
•
•
The unit has been exposed to rain (or
otherwise has become wet); or
The unit does not appear to operate
normally or exhibits a marked change in
performance.
•
Disconnect all cords coming from external
devices before moving the unit.
...............................................................................................
...............................................................................................
013
•
In households with small children, an adult
should provide supervision until the child
is capable of following all the rules
essential for the safe operation of the unit.
...............................................................................................
014
•
Protect the unit from strong impact.
(Do not drop it!)
...............................................................................................
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES
291a
In addition to the items listed under “USING THE UNIT SAFELY” on pages 2 and 3, please read and
observe the following:
Placement
Maintenance
401a
352a
•
This device may interfere with radio and
television reception. Do not use this device in the
vicinity of such receivers.
•
For everyday cleaning wipe the unit with a soft,
dry cloth or one that has been slightly dampened
with water. To remove stubborn dirt, use a cloth
impregnated with a mild, non-abrasive
detergent. Afterwards, be sure to wipe the unit
thoroughly with a soft, dry cloth.
352b
•
Noise may be produced if wireless communica-
tions devices, such as cell phones, are operated in
the vicinity of this unit. Such noise could occur
when receiving or initiating a call, or while
conversing. Should you experience such
problems, you should relocate such wireless
devices so they are at a greater distance from this
unit, or switch them off.
402
•
Never use benzine, thinners, alcohol or solvents
of any kind, to avoid the possibility of discolor-
ation and/or deformation.
Additional Precautions
354a
553
•
Do not expose the unit to direct sunlight, place it
near devices that radiate heat, leave it inside an
enclosed vehicle, or otherwise subject it to
temperature extremes. Excessive heat can deform
or discolor the unit.
•
Use a reasonable amount of care when using the
unit’s buttons, sliders, or other controls; and
when using its jacks and connectors. Rough
handling can lead to malfunctions.
556
•
When connecting / disconnecting all cables,
grasp the connector itself—never pull on the
cable. This way you will avoid causing shorts, or
damage to the cable’s internal elements.
355b
•
When moved from one location to another where
the temperature and/or humidity is very
different, water droplets (condensation) may
form inside the unit. Damage or malfunction may
result if you attempt to use the unit in this
condition. Therefore, before using the unit, you
must allow it to stand for several hours, until the
condensation has completely evaporated.
558b
•
To avoid disturbing your neighbors, try to keep
the unit’s volume at reasonable levels (especially
when it is late at night).
559b
•
When you need to transport the unit, pack it in
shock-absorbent material. Transporting the unit
without doing so can cause it to become
scratched or damaged, and could lead to
malfunction.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Handling CD-ROMs
801
•
Avoid touching or scratching the shiny underside
(encoded surface) of the disc. Damaged or dirty
CD-ROM discs may not be read properly. Keep
your discs clean using a commercially available
CD cleaner.
204
*
Microsoft and Windows are registered trademarks of Microsoft Corporation.
*
206eThe screen shots in this document are used in compliance with the guidelines of the Microsoft Corporation.
*
206j Windows® is known officially as: “Microsoft® Windowsw operating system.”
207
*
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
Mac OS is a trademark of Apple Computer, Inc.
209
*
220
*
All product names mentioned in this document are trademarks or registered trademarks of their respective
owners.
231
*
OMS is a registered trademark of Opcode Systems, Inc.
FreeMIDI is a trademark of Mark of the Unicorn, Inc.
232
*
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents of the Package
The UM-1EX includes the following items. When you open the package, first make sure that
all items are included. If any are missing, contact the dealer where you purchased the UM-
1EX.
USB MIDI Interface UM-1EX
CD-ROM
This contains drivers for use with the UM-1EX.
Owner’s Manual
This is the manual you are reading. Please keep it on hand for reference.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
About the Driver Modes................................................................................................................ 11
Windows XP/2000 users...................................................................................................... 12
Setting the Driver............................................................................................................................ 18
About the Driver Modes................................................................................................................ 21
Driver Installation and Settings.................................................................................................... 21
Mac OS 9 users....................................................................................................................... 26
Basic Use............................................................................................................. 33
Basic Connections and MIDI Flow............................................................................................... 33
Transmitting MIDI messages
from a MIDI keyboard or digital piano to the sequencer software ............................... 33
Transmitting MIDI Messages
from the sequencer software to a MIDI sound module or digital piano....................... 34
Transmitting MIDI messages
from a MIDI Keyboard or other device to a MIDI sound module................................. 35
Appendices.......................................................................................................... 37
About Standard Driver Mode....................................................................................................... 37
Installation of the standard driver ...................................................................................... 37
Standard driver settings ....................................................................................................... 37
Troubleshooting.................................................................................................. 38
Main Specifications ............................................................................................ 47
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Deutsch
Herstellung der Verbindung und Installation der Treiber (Windows)............ 48
Installation des Treibers................................................................................................................. 48
Windows XP/2000-Anwender............................................................................................ 48
Français
Connexion et installation des pilotes (Windows) ............................................ 55
Installation du pilote ...................................................................................................................... 55
Italiano
Collegamento e installazione dei driver (Windows) ........................................ 62
Installazione del driver .................................................................................................................. 62
Utenti Windows XP/2000 .................................................................................................... 62
Collegamento e installazione dei driver (Macintosh) ...................................... 65
Installazione e configurazione dei driver.................................................................................... 65
Utenti Mac OS X .................................................................................................................... 65
Español
Conexión e instalación de los controladores (Windows) ............................... 69
Instalación del controlador............................................................................................................ 69
Usuarios de Windows XP/2000.......................................................................................... 69
Conexión e instalación de los controladores (Macintosh) ............................. 72
Instalación del controlador y ajustes............................................................................................ 72
Usuarios de Mac OS X .......................................................................................................... 72
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of Things and What They Do
4
3
1
5
7
2
8
1
2
USB Cable
Use this when connecting the UM-1EX to your computer.
USB Indicator
This will light when you’ve connected the UM-1EX to your computer and your computer has
detected the UM-1EX.
In order for your computer to detect the UM-1EX, you must install the driver and make settings.
(→“Getting Connected and Installing Drivers” Windows (p. 11) / Macintosh (p. 21))
3
ADVANCED (mode select) Switch
This switches the operating mode.
*
Standard driver mode supports only Windows XP SP2 or later, and Mac OS X.
If you are using Windows 98/Me/2000/XP or XP SP1, or if you are using Mac OS 9, you must
turn the ADVANCED (mode select) Switch ON before you connect the UM-1EX to your
computer.
This mode utilizes the UM-1EX’s special, advanced MIDI driver.
This advanced driver uses *FPT technology for rapid, high-performance
MIDI transmissions.
ON
(Advanced mode)
We recommend use of this mode.
OFF
(Standard mode)
This mode uses the standard MIDI driver included with the OS.
Use this if you do not have the special driver installed.
*FPT=Fast Processing Technology of MIDI Transmission
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4
THRU Switch
Selects the destination to which the MIDI messages that flow in through the UM-1EX’s MIDI IN
cable are to output.
■THRU switch ON/OFF setting
You can use the THRU switch to switch the destination device for MIDI messages from the MIDI
keyboard or digital piano connected to the MIDI IN cable. There is no need to change any cable
connections.
Switch Setting MIDI Message Destination Device
MIDI messages flowing in through the UM-1EX’s MIDI IN cable are routed to the
computer (sequencer software).
OFF
MIDI messages flowing in through the UM-1EX’s MIDI IN cable are output from
the UM-1EX’s MIDI OUT cable. If you are not using sequencer software with your
performances, set this to ON.
ON
fig.connect-change_e
MIDI Message Flow (THRU OFF)
MIDI Message Flow (THRU ON)
*
Don’t change the setting of the THRU switch while playback is in progress. Doing so will cause MIDI
errors.
5
6
MIDI OUT Indicator
This lights when MIDI messages from the computer are transmitted.
MIDI OUT Cable (CONNECT TO MIDI IN)
Connect this to the MIDI IN connector of the device (such as a sound
module) that is to be employed by your computer for playing music.
MIDI Message Flow
7
8
MIDI IN Indicator
This lights when MIDI messages are received from the device connected
to MIDI IN.
MIDI IN Cable (CONNECT TO MIDI OUT)
Connect this to the MIDI OUT connector of the device (such as a MIDI
keyboard) that will be transmitting MIDI messages to your computer.
MIDI Message Flow
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Connected and Installing Drivers (Windows)
What is a driver?
A “driver” is software that transfers data between the UM-1EX and application software running
About the driver modes
The UM-1EX has two operating modes, Advanced mode and Standard driver mode, and a
different driver is used by each mode.
*
Standard driver mode supports only Windows XP SP2 or later.
If you are using Windows 98/Me/2000/ XP or XP SP1, you must turn the ADVANCED (mode
select) Switch ON before you connect the UM-1EX to your computer.
This mode utilizes the UM-1EX’s special, advanced MIDI driver.
This advanced driver uses *FPT technology for rapid, high-performance
MIDI transmissions.
(Advanced mode)
We recommend use of this mode.
ON
(→ “Installing the Driver” (p. 12))
This mode uses the standard MIDI driver included with the OS.
Use this if you do not have the special driver installed.
(→ “Installation of the standard driver” (p. 37))
OFF
(Standard mode)
*FPT = Fast Processing Technology for MIDI Transmission
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Driver
The installation procedure will differ depending on your system.
Please proceed to one of the following sections, depending on the system you use.
• Windows XP/2000 users..........................................................................................p. 12
• Windows Me/98 users.............................................................................................p. 17
Operation of the UM-1EX
Steps to be performed on the UM-1EX itself are marked by a
symbol.
Windows XP/2000 users
1. With the UM-1EX left unconnected, start up Windows.
Do not connect the UM-1EX to the computer until you reach Step 13 (p. 14).
*
*
Disconnect all USB cables except for a USB keyboard and USB mouse (if used).
Log onto Windows using a user name that has administrative privileges (such as Administrator).
2. Open the System Properties dialog box.
Windows XP:
1. Click the Windows start menu, and from the menu, select Control Panel.
2. In “Pick a category,” click “Performance and Maintenance.”
3. In “or pick a Control Panel icon,” click the System icon.
Depending on your setup, the System icon may appear directly in the Control Panel (Classic
view). If so, double-click the System icon.
Windows 2000:
1. Click the Windows Start menu, and from the menu that appears, select Settings | Control
Panel.
2. In Control Panel, double-click the System icon.
3. Click the Hardware tab, then click [Driver Signing].
The Driver Signing Options dialog box will open.
4. In the Driver Signing Options dialog box, select “Ignore,” then click [OK].
If the current setting is “Warn” or “Block,” change this to “Ignore.” Then, when you’ve finished
installing the driver, change it back to the original setting.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click [OK] to close the System Properties dialog box.
6. Exit all currently running software (applications).
Also close any currently open windows. If you are using virus checking or similar software, you
must exit all of these programs as well.
7. Prepare the CD-ROM.
Insert the CD-ROM into your computer’s CD-ROM drive.
*
If the message “Windows can perform the same action each time you insert a disk or
connect a device with this kind of file” appears, [Cancel].
8. From the Windows start menu, choose Run...
9. In the Open field of the “Run...” dialog box, type the following and click [OK].
D: \Driver\XP2k\setup.exe
*
The drive name is “D:” in the example shown here, but may be different on your system. Use the drive
name for your CD-ROM drive.
10.The Driver Setup dialog box will appears.
Click [Next].
Windows XP:
If “Driver Signing Options” in step 4 is set to anything other than “Ignore,” a dialog box with
an “!” or “x” symbol will appear. If a [Continue Anyway] button is displayed, click
[Continue Anyway] to proceed with the installation. If you are unable to continue, click [OK]
and repeat the driver installation from step 1.
Windows 2000:
If “Driver Signing Options” in step 4 is set to anything other than “Ignore,” a dialog box
indicating “Digital Signature Not Found” will appear. If a [Yes] button is displayed, click
[Yes] to proceed with the installation. If you are unable to continue, click [OK] and repeat the
driver installation from step 1.
11.To begin the installation, click [Next] once again. Installation will begin.
The “Setup is now ready to install the drivers” dialog box will appear.
Now you are ready to install the driver.
Operation of the UM-1EX
12.
Set the UM-1EX’s ADVANCED (mode select) Switch to ON.
*
The driver cannot be installed by means of the following procedure if the switch is set to OFF.
If you are using Windows 98/Me/2000/XP or XP SP1, you must turn the ADVANCED (mode
select) Switch ON before you connect the UM-1EX to your computer.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation of the UM-1EX
13.
Connect the UM-1EX to your computer.
A message of “Found New Hardware” will appear. Please wait.
*
This unit is equipped with a protection circuit. A brief interval (a few seconds) after connecting the UM-
1EX is required before the unit will operate normally.
Windows XP:
1. The Found New Hardware Wizard dialog box will appear.
and then click [Next].
2. Make sure that “EDIROL UM-1” is indicated. Then, choose “Install the software
automatically (Recommended) ” and click [Next].
an “!” symbol will appear. Click [Continue Anyway] to proceed with the installation.
Windows 2000:
If “Driver Signing Options” in step 4 is set to anything other than “Ignore,” a dialog box
indicating “Digital Signature Not Found” will appear. Click [Yes] to proceed with the
installation.
14.The Completing the Found New Hardware Wizard dialog box will appear.
Click [Finish].
15.In the Driver Setup dialog box, click [Close].
This completes driver installation.
If the Change System Settings dialog box appears, click [Yes]. Windows will restart
automatically.
*
If you changed the “Driver Signing Options” setting (step 4 on p. 12), restore the original settings
after Windows has restarted.
Next, in order to ensure that MIDI processing occurs smoothly, you need to make settings so that
Background Services is given priority.
(➔ “Giving priority to Background Services” (p. 15))
14
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Giving priority to Background Services
To ensure that MIDI data is handled smoothly, proceed as follows to make this setting.
Windows XP:
1. Open the System Properties dialog box.
1. From the Windows start menu, choose Control Panel.
2. In “Pick a category,” click “Performance and Maintenance.”
3. In “or Pick a Control Panel icon,” click the System icon.
Depending on your setup, the System icon may appear directly in the Control Panel (Classic
view). If so, double-click the System icon.
2. Click the Advanced tab.
3. In the right side of the Performance area, click [Settings].
The Performance Options dialog box will open.
4. Click the Advanced tab.
5. In the Processor scheduling area, choose
“Background services,” and click [OK].I
6. In the System Properties dialog box, click [OK].
The System Properties dialog box will close.
Next, you’ll make the driver settings. (➔ “Setting the Driver” (p. 18))
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 2000:
1. Click the Windows Start button, and from the menu that appears, select Settings | Control
Panel.
2. In Control Panel, double-click the System icon.
3. Click the Advanced tab.
4. At the right of the Performance field, click [Performance Options].
The Performance Options dialog box will appear.
fig.back2000
5. In the Application response field, choose
“Background services” and click [OK].
6. Click [OK] to close the System Properties dialog box.
The System Properties dialog box will close.
Next, you’ll make the driver settings. (➔ “Setting the Driver” (p. 18))
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows Me/98 users
1. With the UM-1EX left unconnected, start up Windows.
2. Exit all currently running software.
Also close any open windows. If you are using virus checking or similar software, be sure to exit it
as well.
3. Prepare the CD-ROM.
Insert the CD-ROM into the CD-ROM drive of your computer.
4. Click the Windows Start menu. From the menu that appears, select Run....
The “Run...” dialog box will appear.
5. In the dialog box that appears, input the following into the “Open” field, and click [OK].
D: \Driver\Me98\Setup.exe
*
The drive name is “D:” in the example shown here, but may be different on your system. Use the drive
name for your CD-ROM drive.
6. The Driver Setup dialog box will appears. Click [Next].
7. To begin the installation, click [Next] once again. Installation will begin.
The “Setup is now ready to install the drivers” dialog box will appear.
Now you are ready to install the driver.
Operation of the UM-1EX
8.
Set the UM-1EX’s ADVANCED (mode select) Switch to the ON position.
*
The driver cannot be installed by means of the following procedure if the switch is set to OFF.
If you are using Windows 98/Me/2000/XP or XP SP1, you must turn the ADVANCED (mode
select) Switch ON before you connect the UM-1EX to your computer.
Operation of the UM-1EX
9.
Connect the UM-1EX to your computer.
A message of “Found New Hardware” will appear. Please wait.
*
This unit is equipped with a protection circuit. A brief interval (a few seconds) after connecting the UM-
1EX is required before the unit will operate normally.
10.In the Driver Setup dialog box, click [Close].
Next, you’ll make the driver settings. (➔ “Setting the Driver” (p. 18))
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Driver
The following describes the settings needed to use the UM-1EX with Media Player or other
sequencer software using Windows standard device settings.
If you are using sequencer software that does not utilize Windows standard device settings, make
the device settings within the sequencer software.
Windows XP users
1. Open the Sounds and Audio Devices Properties dialog box.
1. From the Windows start menu, choose Control Panel.
2. In “Pick a category,” click Sound, Speech, and Audio Devices.
3. In “or Pick a Control Panel icon,” click the Sounds and Audio Devices icon.
Depending on your setup, the Sounds and Audio Devices icon may appear directly in the
Control Panel (Classic view). If so, double-click the Sounds and Audio Devices icon.
2. Click the Audio tab.
fig.XP-E
3. For MIDI music playback, click the ▼ located at the right
of [Default device], and select the MIDI device from the
list that appears.
Selecting “EDIROL UM-1 MIDI” enables sounds to be
played from the sound module connected to the UM-
1EX’s MIDI OUT cable with Media Player or other
sequencer software utilizing Windows standard device
settings.
4. Close the Sounds and Audio Devices Properties dialog
box.
Click [OK] to complete the settings.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 2000/Me users
1. Open the Sounds and Multimedia Properties dialog box.
1. Click the Windows start button, and from the menu that appears, select Settings | Control
Panel.
2. In Control Panel, double-click the Sounds and Multimedia icon.
If Sounds and Multimedia icon is not displayed, click “Show all control panel options” in
the frame at the left.
2. Click the Audio tab.
fig.2K-E
3. Click ▼ in the MIDI Music Playback [Preferred device]
menu and select the MIDI device from the list that
appears.
Selecting “EDIROL UM-1 MIDI” enables sounds to be
played from the sound module connected to the UM-
1EX’s MIDI OUT cable with Media Player or other
sequencer software utilizing Windows standard device
settings.
4. Close the Sounds and Multimedia Properties dialog box.
Click [OK] to complete the settings.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows 98 users
1. Open the Multimedia Properties dialog box.
1. Click the Windows Start menu, and from the menu that appears, select Settings | Control
Panel.
2. In Control Panel, double-click the Multimedia icon.
2. Click the MIDI tab.
fig.2K-E
3. Select [Single instrument], and select the MIDI device
from the list that appears.
If you want to use Media Player to play a sound module
connected to the UM-1EX’s MIDI OUT cable, select
“EDIROL UM-1 MIDI.”
4. Close the Multimedia Properties dialog box.
Click [OK] to complete the settings.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Connected and Installing Drivers (Macintosh)
What is a driver?
A “driver” is software that transfers data between the UM-1EX and application software running
from your application to the UM-1EX, and from the UM-1EX to your application.
About the driver modes
The UM-1EX has two operating modes, Advanced mode and Standard driver mode, and a
different driver is used by each mode.
*
Standard driver mode supports only Mac OS X.
If you’re using OS 9, you must turn the ADVANCED (mode select) Switch ON before you
connect the UM-1EX to your Macintosh.
This mode utilizes the UM-1EX’s special, advanced MIDI driver.
MIDI transmissions.
(Advanced mode)
We recommend use of this mode.
ON
(→ “Driver Installation and Settings” (p. 21))
This mode uses the standard MIDI driver included with the OS.
OFF
Use this if you do not have the special driver installed.
(Standard mode)
(→“Installation of the standard driver” (p. 37))
*FPT = Fast Processing Technology for MIDI Transmission
Driver Installation and Settings
The installation procedure will differ depending on your system.
Please proceed to one of the following sections, depending on the system you use.
• Mac OS X users................................................................................................ (p. 22)
• Mac O S9 users ................................................................................................ (p. 26)
Operation of the UM-1EX
Steps to be performed on the UM-1EX itself are marked by a
symbol.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Mac OS X users
■ Installing the driver
*
*
If the “Authenticate” dialog box appears during the installation, input the password and click “OK.”
What you actually see on your Macintosh screen may be different, depending on your computing
environment and the operating system you’re using.
1. With the UM-1EX left unconnected, start up Macintosh.
Disconnect all USB cables other than those for your keyboard and mouse, and restart your Macintosh.
*
2. Exit all currently running software (applications).
3. Prepare the CD-ROM.
Insert the CD-ROM into the CD-ROM drive of your Macintosh.
4. In the Driver (Mac OS X) folder of the CD-ROM, double-click UM1USBDriver.pkg.
*
Click “Continue.”
5. The display will indicate “Welcome to the EDIROL UM-1Driver Installer.” Click [Continue].
6. The display will indicate “Select a Destination.”
Click the drive in which the operating system is installed to select it, and then click [Continue].
*
Select your startup disk as the drive.
7. The display will indicate “Easy Install.”
Click [Install] or [Upgrade].
8. The display will indicate “Installing this software requires you to restart your computer when
the installation is done.”
Click [Continue Installation].
9. The display will indicate “The software was successfully installed.”
Click [Restart] to restart your Macintosh.
This completes installation of the UM-1 driver.
Next, make MIDI device settings. (→“Setting the driver” (p. 23))
22
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Setting the driver
The following describes the settings enabling use of the UM-1EX with sequencer software using
Macintosh standard device settings.
If you are using sequencer software that does not utilize Macintosh standard device settings, make
the device settings within the sequencer software.
*
What you actually see on your Macintosh screen may be different, depending on your computing
environment and the operating system you’re using.
Operation of the UM-1EX
1.
2.
Set the UM-1EX’s ADVANCED (mode select) Switch to the ON position.
Operation of the UM-1EX
Connect the UM-1EX to your Macintosh.
*
*
Connect the cable to the USB connector of the Macintosh itself, not to the USB connector of the keyboard.
This unit is equipped with a protection circuit. A brief interval (a few seconds) after connecting the UM-
1EX is required before the unit will operate normally.
3. Open the Applications folder of your Macintosh hard disk. In the Utilities folder, double-click
Audio MIDI Setup to open the Audio MIDI Setup dialog box.
Click MIDI Devices
4
Click Add Device
6
Click Show Info
7
4. Click the MIDI Devices tab.
5. Confirm that UM-1 appears in the Audio MIDI Setup dialog box.
*
If UM-1 does not appear or if it is grayed out, it means that the UM-1EX is not being recognized properly.
Click Rescan MIDI. Also try disconnecting and reconnecting the UM-1EX.
*
Previous settings from installation of a different version of the driver may still remain. If this is the case,
click on the grayed UM-1 or EDIROL UM-1 to select it, then click Remove Selected Device to delete
the settings.
6. Click Add Device.
new external device will appear.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Set the device name.
1. With the new external device selected, click Show Info.
2. Enter the name in the Device Name field.
8. Connect the ▼ and ▲ symbols (which signify the outputs and inputs) of the UM-1 icon to those of
the new external device icon by using the mouse to drag between them.s
Use the mouse to
drag a connection
9. If running Mac OS X v10.3 or earlier: Close the Audio MIDI Setup dialog box. The settings are
completed.
If running Mac OS X v10.3 or later: Confirm that MIDI is being transmitted and received
correctly. Perform Steps 10–13 (p. 25).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
10.Click Test Setup.
The shape of the mouse
cursor changes
.
11.Click the area shown in
the illustration. If the
Test Setup
10, 12
UM-1EX’s MIDI OUT
indicator starts blinking,
the settings are correct.
Use the mouse to
drag a connection
12.Click Test Setup and
complete the
confirmation.
Click the icon
11
13.Close the Audio MIDI Setup dialog box.
.
When using the UM-1EX with your sequencer software
Before using the UM-1EX with your sequencer software, please note the following points.
• Connect the UM-1EX to your Macintosh before you start up your sequencer software.
• Do not disconnect the UM-1EX from your Macintosh while your sequencer software is
running.
Quit your sequencer software before you disconnect the UM-1EX from your Macintosh.
• Turn off the Sleep function of your Macintosh.
• The UM-1EX will not operate in the Mac OS X Classic environment. Use the UM-1EX when
the Classic environment is not running.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Mac OS 9 users
■ Installing the UM-1 driver
Use either OMS or FreeMIDI as the MIDI driver.
The included UM-1 driver is an add-on module for using the UM-1EX with OMS or FreeMIDI.
OMS can be found in the OMS 2.3.8 E folder within the OMS (Mac OS 9) folder of the CD-ROM.
If you would like to know more about OMS, refer to OMS_2.3_Mac.pdf which can be found in the
same folder.
*
*
Either OMS or FreeMIDI must be installed in your Macintosh, as appropriate for the sequencer software
you are using.
If you install OMS after installing the UM-1 driver, you must install the UM-1 driver once again.
If a UM-1EX is already connected to your Macintosh when you install the driver, a message like
the following will appear when the Macintosh is started up. Perform the steps described below as
appropriate for the message that is displayed.
If the screen indicates:
“Software needed for the USB device “UM-1” is not available. Would you like to look for
the software on the Internet?”➔ click [Cancel].
1. With the UM-1EX left unconnected, start up Macintosh
Disconnect all USB cables other than those for your keyboard and mouse, and restart your Macintosh.
*
2. Exit all currently running software (applications).
3. Prepare the CD-ROM. Insert the CD-ROM into the CD-ROM drive of your Macintosh.
4. Double-click the UM-1 Driver-E Installer icon (found in the Driver E (Mac OS 9) folder of the CD-
ROM) to start up the installer.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Verify the Install Location, and click [Install].
The installation location will be shown differently depending on your system. Make sure that you
have selected the startup disk for the system you are currently using.
fig.05-20
6. If a message like the following is displayed,
click [Continue].
The other currently running software will exit,
and installation will continue.
7. A dialog box will indicate Installation was successful.
Click [Restart] to restart your Macintosh.
Next, make the driver settings.
• OMS users ..................................................................................................................p. 28
• FreeMIDI users..........................................................................................................p. 31
27
Download from Www.Somanuals.com. All Manuals Search And Download.
■ OMS settings
If you are using FreeMIDI, proceed to “FreeMIDI settings” (p. 31).
Operation of the UM-1EX
1.
2.
Set the UM-1EX’s ADVANCED (mode select) Switch to the ON position.
Operation of the UM-1EX
Connect the UM-1EX to your Macintosh.
*
*
Connect the cable to the USB connector of the Macintosh itself, not to the USB connector of the keyboard.
This unit is equipped with a protection circuit. A brief interval (a few seconds) after connecting the UM-
1EX is required before the unit will operate normally.
fig.3-3
3. From the CD-ROM, drag the Driver E (Mac OS 9) - OMS Setting folder into the
Opcode - OMS Applications folder on the hard disk of your Macintosh to copy it
there.
fig.3-4
4. In the Opcode - OMS Applications folder where you installed OMS, double-click
OMS Setup to start it up.
fig.3-5_35
5. If a dialog box like the one shown here appears,
click [Turn It Off]. A confirmation dialog box
will then appear, so click [OK].
*
We recommend that you turn off AppleTalk, by
selecting Chooser from the Apple menu.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
fig.3-6_35
6. The Create a New Studio Setup dialog box will
appear. Click [Cancel].
If you accidentally clicked [OK], click [Cancel] in
the next screen.
fig.3-8_35
7. Choose “Open” from the File menu.
From the OMS Setting folder that you copied in
step 3, select the UM-1 file, and click [Open].
A screen like the one shown here will appear.
fig.3-9_35
8. From the Edit menu, select OMS MIDI Setup.
In the OMS MIDI Setup dialog box that appears,
check Run MIDI in background, and click [OK].
29
Download from Www.Somanuals.com. All Manuals Search And Download.
fig.3-10_40
A diamond mark ( ) indicates the settings are enabled.
9. From the File menu, choose Make Current.
If you are unable to select Make Current, it has
already been applied, and you may continue to
the next step.
10.Verify that MIDI transmission and reception
can be performed correctly.
From the Studio menu, choose Test Studio.
fig.OMS3
11.When you move the mouse cursor near the
MIDI connector icon, the cursor will change to a
ꢀ shape.
Click the MIDI connector icon shown in the
illustration. If the UM-1EX’s MIDI OUT
indicator starts blinking, the settings are correct.
12.Exit OMS Setup.
From the File menu, choose [Exit]. If the
AppleTalk confirmation dialog box appears,
click [OK] to close the dialog box.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
■ FreeMIDI settings
Operation of the UM-1EX
1.
Set the UM-1EX’s ADVANCED (mode select) Switch to the ON position.
Operation of the UM-1EX
2.
Connect the UM-1EX to your Macintosh.
*
*
Connect the cable to the USB connector of the Macintosh itself, not to the USB connector of the keyboard.
This unit is equipped with a protection circuit. A brief interval (a few seconds) after connecting the UM-
1EX is required before the unit will operate normally.
3. From the CD-ROM, drag the Driver E (Mac OS 9) - FreeMIDI Setting folder into the FreeMIDI
Applications folder on the hard disk of your Macintosh to copy it there.
4. Open the FreeMIDI Applications folder from the location into which you installed FreeMIDI, and
double-click the FreeMIDI Setup icon to start it up.
When “OMS is installed on this computer...” appears, click [FreeMIDI].
5. The first time you start up, use the following procedure.
1. A dialog box saying “Welcome to FreeMIDI!” will appear.
Click [Continue].
2. The FreeMIDI Preferences dialog box will appear.
Click [Cancel].
3. The About Quick Setup dialog box will appear.
Click [Cancel].
6. From the File menu, choose Open.
If you are unable to select Open, return to step 4 and continue the procedure.
1. From the File menu, choose FreeMIDI Preference.
2. Uncheck “Use OMS when available.”
3. Close FreeMIDI.
7. Select UM-1 from the FreeMIDI Setting folder you copied in step 3, and click [Open].
8. Verify that MIDI transmission and reception occur correctly.
From the MIDI menu, choose Check Connections.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
fig.FreeMIDI
9. The mouse cursor will change to the shape of a
keyboard.
Click the icon shown in the illustration. If the
UM-1EX’s MIDI OUT indicator starts blinking,
the settings are correct.
10.Once again choose the MIDI menu command Check Connections to end the test.
11.From the File menu, choose Quit to exit FreeMIDI Setup.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Use
This chapter describes different basic methods of connecting the UM-1EX according to how the
UM-1EX is to be used.
Basic Connections and MIDI Flow
Transmitting MIDI messages from a MIDI keyboard or digital
piano to the sequencer software
To transmit MIDI messages from a MIDI keyboard or digital piano to the sequencer software or
make a MIDI recording of a keyboard performance or other performance using sequencer
software on your computer, make the following connections and settings.
fig.connect-in_e
MIDI Keyboard
THRU OFF
Message Flow
Digital Piano
MIDI messages are transmitted
to the sequencer software.
Connect to the
computer’s
USB connector.
Connect to the MIDI OUT connector
of the MIDI keyboard or digital piano.
MIDI Message Flow
MIDI device setting
MIDI IN
UM-1 MIDI
*
Make the device settings within the sequencer software.
THRU switch setting
THRU Switch
OFF
MIDI messages from the MIDI device (e.g, MIDI keyboard, digital piano) connected to the UM-1EX’s MIDI IN
cable are transmitted to the computer.
Don't change the setting of the THRU switch while you're using the UM-1EX. Doing so will cause MIDI errors.
*
If you are experiencing duplicate notes (i.e., if your sound generating device plays two notes for each note it should play), turn
Local Control OFF on your sound generating device, or turn the Thru function OFF in your sequencer software. For details on
how to makDe tohewsenselottiangds,frreofemr toWthewowwn.eSr’sommanaunalufoarlyso.ucroemqui.pAmellntM. anuals Search And Download.
33
Transmitting MIDI Messages from the sequencer software to a
MIDI sound module or digital piano
If transmitting MIDI messages from the sequencer software to a MIDI sound module or digital
piano, or if using a MIDI sound module’s or digital piano’s sound generator to play the sounds
from the playback of sequencer software on the computer, make the following connections and
settings.
fig.connect-out_e
Connect to the MIDI IN
connector of the MIDI sound
USB connector.
THRU OFF
MIDI Sound Module
MIDI messages are transmitted
from the sequencer software.
Message Flow
MIDI Message Flow
Digital Piano
MIDI device setting
MIDI OUT
UM-1 MIDI
For more on how to make the settings, refer to “Getting Connected and Installing Drivers”
(Windows:p. 11 / Macintosh:p. 21).
If you are using sequencer software that does not utilize Windows or Macintosh standard device settings, make
the device settings within the sequencer software.
*
THRU switch setting
THRU Switch
OFF
MIDI messages from the computer are transmitted to the MIDI device (e.g., MIDI sound module,
digital piano) connected to the UM-1EX’s MIDI OUT cable.
Don't change the setting of the THRU switch while you're using the UM-1EX. Doing so will cause MIDI
errors.
*
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Transmitting MIDI messages from a MIDI Keyboard or other
device to a MIDI sound module
If you want to play a MIDI keyboard and send MIDI messages to a MIDI sound module, make the
connections and settings shown below.
There is no need to connect the UM-1EX to a computer.
fig.connect-thru_e
Connect to the MIDI IN
connector of the MIDI
MIDI Message Flow
sound module.
Message Flow
THRU ON
MIDI Sound Module
MIDI Keyboard
Connect to the MIDI OUT
Message Flow
connector of the MIDI
keyboard.
MIDI device setting
Since no computer is used, there is no need to make MIDI device settings.
THRU switch setting
THRU Switch
ON
MIDI messages from the MIDI keyboard or digital piano connected to the UM-1EX’s MIDI IN
cable will be sent to the MIDI sound module connected to the UM-1EX’s MIDI OUT cable. Even if
the UM-1EX is connected to a computer, no MIDI messages will be sent to the computer.
Don't change the setting of the THRU switch while you're using the UM-1EX. Doing so will cause MIDI
errors
*
35
Download from Www.Somanuals.com. All Manuals Search And Download.
■ THRU switch ON/OFF setting
You can use the THRU switch to switch the destination device for MIDI messages from the MIDI
keyboard or digital piano connected to the MIDI IN cable. There is no need to change any cable
connections.
Switch Setting
OFF
MIDI Message Destination Device
MIDI messages are transmitted to the computer (sequencer software).
MIDI messages are transmitted to the MIDI device (e.g., MIDI sound mod-
ule) connected to the MIDI OUT cable.
ON
fig.connect-change_e
MIDI Message Flow (THRU OFF)
MIDI Message Flow (THRU ON)
*
Don't change the setting of the THRU switch while you're using the UM-1EX. Doing so will cause MIDI
errors.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendices
About Standard Driver Mode
Use this mode when using the standard MIDI driver provided with the operating system.
*
Standard driver mode supports only Windows XP SP2 or later, and Mac OS X.
If you are using Windows 98/Me/2000/XP or XP SP1, or if you are using Mac OS 9, you must
turn the ADVANCED (mode select) Switch ON before you connect the UM-1EX to your
computer.
Installation of the standard driver
*
Disconnect all USB cables other than those for your keyboard and mouse, and restart your Macintosh.
2. Exit all currently running software (applications).
3. Set the UM-1EX’s ADVANCE DRIVER switch (mode switch) to OFF.
4. Connect the UM-1EX to the computer.
The driver is automatically installed.
*
This unit is equipped with a protection circuit. A brief interval (a few seconds) after connecting the UM-
1EX is required before the unit will operate normally.
Standard driver settings
These settings enable use of the UM-1EX with sequencer software that uses Windows or
Macintosh standard device settings.
If using sequencer software that does not utilize Windows standard device settings, make the
device settings within the sequencer software. For instructions on the device settings for your
particular sequencer software, refer to the owner’s manual that was supplied with it.
When using Windows XP
1. In accordance with Steps 1 in “Windows XP users” (p. 18), open the Audio tab in the Sounds and
Audio Devices Properties dialog box.
2. Click the ▼ for [Default device] in the MIDI music playback menu and select the USB audio
device from the list that appears.
Depending on your computing environment, “(2)” or some other number may be added at the end
of the port name.
When using Macintosh (Mac OS X)
The procedure is the same as for Advanced mode. Refer to “Setting the driver” (p. 23).
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you experience problems, read this chapter first. It contains tips for solving most problems.
*
For details on operating your Windows or Macintosh computer, refer to the owner’s manual of the
computer and operating system you are using.
Problems Related to the USB Driver
Cannot install the driver correctly
Install the UM-1 driver once again as described in Getting Connected and Installing Drivers
(Windows) (p. 11) or Getting Connected and Installing Drivers (Macintosh) (p. 21).
Is the UM-1EX connected correctly?
Make sure that the USB connector of your computer is connected to the UM-1EX.
Could any other USB device be connected?
Before you install, disconnect all USB devices except for your mouse and keyboard.
Could other software or resident software (such as antivirus programs) be running?
Installation may not be successful if other programs are running.
Be sure to close all other programs before installation.
Is the CD-ROM correctly inserted into your CD-ROM drive?
Installation is not possible unless the CD-ROM included with the UM-1EX is inserted in your CD-
ROM drive. Make sure that the CD-ROM is correctly inserted into your CD-ROM drive.
Are you attempting to install from a networked CD-ROM drive?
You cannot install from a networked CD-ROM drive.
Is the CD-ROM or the lens of the CD-ROM drive be dirty?
If the CD-ROM or the lens of the CD-ROM drive is dirty, the installer may not work correctly.
Clean the disc and/or lens using a commercially-available CD cleaner or lens cleaner.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Is your computer’s power-conservation mode turned off?
If power-conservation settings are enabled on your computer, please disable any such settings.
For the procedure, refer to the owner’s manual of your computer.
Is there sufficient free space on your hard disk?
Delete unneeded files to increase the amount of free space. After deleting the unneeded files,
empty the recycling bin.
Could the UM-1EX’s ADVANCED (mode select) Switch be OFF?
Turn the UM-1EX’s ADVANCED (mode select) Switch ON, restart Windows, and re-install the
driver.
Does your computer or USB hub have sufficient power supply capacity?
The UM-1EX cannot be connected if insufficient power is supplied to it. Check whether one of the
following cases apply.
• If you are using the UM-1EX with a notebook computer that is running on its battery,
operation may be unreliable with some models of computer. If this is the case, connect the
• The power conservation mode of your computer may limit the power that is supplied to
USB. Check the settings of your computer.
• In some cases, the UM-1EX cannot be used with a bus-powered hub (a hub that does not
contain a power supply). Please use a self-powered hub (a hub that contains a power
supply).
Is USB enabled on your computer?
Refer to the operation manual for your computer, and make sure that USB is enabled.
Does your computer meet the USB specifications?
If you are using a computer that does not fulfill the electrical requirements of the USB
specifications, operation may be unstable. In this case, you may be able to solve the problem by
connecting a USB hub.
In the Device Manager, do you see “Other device,” “Unknown device,” or a device
for which “?”, “!” or “x” is displayed? (Windows)
If the driver installation could not be successfully completed, the installed driver may remain in an
incomplete state.
Re-install the driver. (➔“Installing the Driver” (p. 12))
Is OMS or FreeMIDI installed? (Mac OS 9)
The UM-1 driver cannot be installed unless OMS or FreeMIDI are installed. Please install OMS or
FreeMIDI.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows XP/2000 displays a “Hardware Installation” or “Digital
Signature Not Found” dialog box
Did you make “Driver Signing Options”?
In order to install/re-install the driver, you must make the settings described in “Driver Signing
Options” (p. 12).
(Windows)
Did you connect the UM-1EX to a different USB connector than the one you used when
installing the driver?
different USB connector, you may be asked for the driver file even though the driver has already
been installed in your computer. (Such a response does not indicate a malfunction.)
Proceed as follows to install the driver.
1. Connect the UM-1EX to the computer.
Windows XP:
If the message “Connect to Windows Update to search for software?” appears, choose “No”
and then click [Next].
2. Choose “Search for the best driver in these locations” and click [Next].
If a dialog box with an “!” or “x” symbol will appear, click [Continue Anyway] to proceed with
the installation. If you are unable to continue, click [OK] and repeat the driver installation.
(➔“Installing the Driver” (p. 12))
Windows 2000:
If a dialog box indicating “Digital Signature Not Found” will appear, click [Yes] to proceed
with the installation. If you are unable to continue, click [OK] and repeat the driver installation.
(➔“Installing the Driver” (p. 12))
2. The Completing the Found New Hardware Wizard dialog box will appear.
Click [Finish].
3. If the Change System Settings dialog box appears, click [Yes]. Windows will restart
automatically.
If you are unable to complete driver installation using the above method, repeat the driver
installation. (➔“Installing the Driver” (p. 12))
40
Download from Www.Somanuals.com. All Manuals Search And Download.
“Find new hardware wizard” does not execute automatically
“Find new hardware wizard” ends before the process is completed
“Found unknown device” appears even though you installed the driver
(Windows)
Is the USB cable connected correctly?
Make sure that the UM-1EX’s USB cable and your computer are correctly connected.
It may take about 15seconds (or more) after the USB cable is connected.
Does your computer or USB hub have sufficient power supply capacity?
The UM-1EX cannot be connected if insufficient power is supplied to it. Check whether one of the
following cases apply.
• If you are using the UM-1EX with a notebook computer that is running on its battery, operation
may be unreliable with some models of computer. If this is the case, connect the AC adaptor to
your notebook computer.
• The power conservation mode of your computer may limit the power that is supplied to USB.
Check the settings of your computer.
• In some cases, the UM-1EX cannot be used with a bus-powered hub (a hub that does not contain a
power supply). Please use a self-powered hub (a hub that contains a power supply).
Is USB enabled on your computer?
Refer to the operation manual for your computer, and make sure that USB is enabled.
Does your computer meet the USB specifications?
If you are using a computer that does not fulfill the electrical requirements of the USB
specifications, operation may be unstable. In this case, you may be able to solve the problem by
connecting a USB hub.
If the above actions do not solve the problem, it is possible that the UM-1EX has been incorrectly
detected by the computer. Please reinstall the driver from the beginning of the procedure.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
UM-1EX is not detected when making OMS or FreeMIDI settings
(Mac OS 9 users)
Is the UM-1EX detected?
• Reconnect the UM-1EX.
• If other USB devices are connected, connect only the UM-1EX.
• It is possible that the Macintosh did not correctly detect and initialize the UM-1EX. Leave the
UM-1EX connected, and restart your Macintosh. If it is still not detected, shut down your
Macintosh, and then restart it.
• In some cases, the UM-1EX will not be detected if you have connected it to the USB connector
located on the keyboard of the Macintosh. Please connect it to a USB connector on the
Macintosh itself.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting the Driver
If you were unable to install the driver according to the procedure given, the UM-1EX may not be
recognized correctly by the computer. In this case, use the following procedure to delete the
driver, and then follow the procedure to install the driver once again.
Windows users
Here’s how to uninstall the dedicated driver.
1. Start up Windows with the UM-1EX disconnected.
Disconnect all USB cables other than a USB keyboard or USB mouse.
*
*
If you are using Windows XP Professional/2000, log on as a user that has administrative privileges (e.g.,
Administrator).
2. Insert the CD-ROM into the CD-ROM drive of your computer.
3. From the Windows Start menu, choose “Run....”
In the Run dialog box, input the following into the Open field, and click [OK].
Windows XP/2000 users:
Windows Me/98 users:
D:\Driver\XP2k\Uninstal.exe
D:\Driver\Me98\Uninstal.exe
The drive name is “D:” in the example shown here, but may be different on your system. Use the drive
name for your CD-ROM drive.
4. Follow the on-screen instructions to uninstall the driver.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Macintosh (Mac OS X) users
1. Start up Macintosh with the UM-1EX disconnected.
Disconnect all USB cables other than a USB keyboard or USB mouse.
2. Prepare the CD-ROM.
Insert the CD-ROM into the CD-ROM drive of your Macintosh.
3. In the Driver (Mac OS X) folder of the CD-ROM, double-click “UM1_Uninstaller.”
4. The display will indicate “This uninstalls EDIROL UM-1 driver from this Macintosh.”; click
[Uninstall].
If any other message appears, proceed as directed by that message.
5. The display will indicate “Are you sure to uninstall the driver?”; click [OK].
6. The “Authenticate” dialog box will appear; enter the password and click [OK].
7. The display will indicate “Uninstllation is completed.”; click [Restart]. Your Macintosh will
then restart.
Macintosh (Mac OS 9) users
1. Start up Macintosh with the UM-1EX disconnected.
Disconnect all USB cables other than a USB keyboard or USB mouse.
2. From the system extensions folder inside the System folder, drag “USB UM-1 Driver” into
the trash to delete it.
3. Delete UM-1 from the OMS Folder inside the System folder, or drag UM-1 Driver from the
FreeMIDI Folder inside the System folder to the trash.
4. Restart the Macintosh.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Problems When Using the UM-1EX
Sound is interrupted during MIDI playback
In Windows, did you make the setting described in “Giving priority to background
services”?
In order to ensure that MIDI processing occurs smoothly, make the setting described inGiving
priority to Background Services. (➔Windows XP (p. 15) / Windows 2000 (p. 16))
Did you plug in the USB cable, or unplug it while an software was running?
Exit all software that are using the UM-1EX, and re-connect the UM-1EX.
Is your computer in Suspend or Sleep mode?
If so, get your computer to resume normal operation, then exit all software that are using the UM-
1EX. Next re-connect the UM-1EX.
Are you running multiple software?
If multiple software are running simultaneously, an error message may appear. If this occurs, click
[OK] and exit the other software.
Even if an software window is closed, it is still running if it appears in the taskbar. Be sure to exit
unneeded software displayed.
Playback or recording halts midway through, and then becomes impossible
Was a heavy processing load experienced while using the UM-1EX, such as accessing
the CD-ROM drive or a network?
If an operation involving a heavy processing load is performed while the UM-1EX is in use, it may
not operate correctly. If this occurs, stop playback/recording, and then try resuming playback/
recording. If you are still unable to play back/record, exit all software that use the UM-1EX,
disconnect the UM-1EX from the computer and then reconnect it.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating system becomes unstable
Operation becomes unstable when the computer is started up with the UM-1EX
already connected
Please start up your computer with the UM-1EX disconnected, and then connect the UM-1EX. On
a computer that uses a USB keyboard, starting up the computer with the UM-1EX already
connected may cause operation to become unstable. In this case, start up the computer with the
UM-1EX disconnected, and then connect the UM-1EX.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Specifications
■ UM-1EX: USB MIDI Interface
Controllers
ADVANCED switch
THRU switch
Connectors
MIDI IN Cable x 1 (16 MIDI Channels)
MIDI OUT Cable x 1 (16 MIDI Channels)
USB Cable
Power Supply
Supplied from the computer
Current Draw
70 mA
Dimensions
75 (W) x 41 (D) x 20 (H) mm
3 (W) x 1-5/8 (D) x 13/16 (H) inches
Weight
120 g / 5 oz
Accessories
Owner’s Manual
CD-ROM
962a
*
In the interest of product improvement, the specifications, appearance, and/or contents of this unit are
subject to change without prior notice.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Herstellung der Verbindung und
Installation der Treiber (Windows)
Installation des Treibers
Windows XP/2000-Anwender
1. Starten Sie Windows bei nicht angeschlossenem UM-1EX.
Schließen Sie den UM-1EX nicht an den Computer, solange Sie nicht Schritt 13 erreicht haben (S. 50).
*
*
Entfernen Sie sämtliche USB-Kabel außer denen der USB-Tastatur und der USB-Maus (falls vorhanden).
Melden Sie sich in Windows mit einem Benutzernamen an, der über Administrationsrechte verfügt
(beispielsweise Administrator).
2. Öffnen Sie das Dialogfeld Systemeigenschaften.
Windows XP:
1. Klicken Sie auf das Windows-Start-Menü und wählen Sie im Folgemenü Systemsteuerung.
2. Klicken Sie in “Wählen Sie eine Kategorie” auf “Leistung und Wartung”.
3. Klicken Sie in “oder wählen Sie ein Systemsteuerungssymbol” auf das Symbol System.
Je nach Einstellung wird das Symbol System manchmal direkt in der klassischen Ansicht der
Systemsteuerung angezeigt. Doppelklicken Sie in diesem Fall auf das System-Symbol.
Windows 2000:
1. Klicken Sie auf das Windows-Start-Menü und wählen Sie im Folgemenü Einstellungen |
Systemsteuerungen.
2. Doppelklicken Sie auf das System-Symbol in Systemsteuerung.
3. Klicken Sie auf den Reiter Hardware und dann auf [Treibersignatur].
Daraufhin werden die Treibersignaturoptionen angezeigt.
4. Wählen Sie im Dialogfeld Treibersignaturoptionen die Option “Ignorieren” und klicken Sie
dann auf [OK].
Wenn derzeit “Warnen” oder “Sperren” eingestellt ist, ändern Sie es zu “Ignorieren”. Stellen Sie
nach abgeschlossener Installation des Treibers die ursprünglichen Einstellungen wieder her.
5. Klicken Sie im Dialogfeld Systemeigenschaften auf [OK]. Das Dialogfeld Systemeigenschaften
wird geschlossen.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Beenden Sie alle aktuell ausgeführten Programme (Anwendungen).
Schließen Sie außerdem alle noch geöffneten Programmfenster. Wenn Sie ein Antivirus-Programm
oder eine ähnliche Software benutzen, müssen Sie diese Programme ebenfalls beenden.
7. Halten Sie die CD-ROM bereit.
Legen Sie die CD-ROM in das CD-ROM-Laufwerk Ihres Computers.
*
Wenn die Meldung “Windows kann jedes Mal, wenn Sie eine Diskette einlegen oder ein Gerät
mit dieser Dateiart anschließen, die gleiche Aktion ausführen” angezeigt wird, klicken Sie auf
[Abbrechen].
8. Wählen Sie “Ausführen...” aus dem Windows-Start-Menü.
9. Geben Sie Folgendes in das Eingabefeld Offen des Dialogfeldes “Ausführen...” ein und klicken Sie
danach auf [OK].
D: \Driver\XP2k\setup.exe
*
Der Laufwerkname ist “D:” in dem hier gezeigten Beispiel. In Ihrem System kann er jedoch anders sein.
Geben Sie den Laufwerksnamen Ihres CD-ROM-Laufwerks an.
10.Daraufhin wird das Dialogfeld Treiber-Setup angezeigt.
Klicken Sie auf [Weiter].
Windows XP:
Wenn “Treibersignaturoptionen” in Schritt 4 anders lauten als “Ignorieren,” erscheint ein
Dialogfeld mit “!” oder “x”. Wenn die Schaltfläche [Continue Anyway] (In jedem Fall Weiter)
erscheint, klicken Sie auf [Continue Anyway] (In jedem Fall Weiter), um die Installation
fortzusetzen. Wenn Sie nicht fortfahren können, klicken Sie auf [OK] und wiederholen Sie
Treiberinstallation von Schritt 1 an.
Windows 2000:
Wenn “Treibersignaturoptionen” in Schritt 4 anders lauten als “Ignorieren,” erscheint ein
Dialogfeld mit “Digital Signature Not Found” (Digitalsignatur nicht gefunden). Wenn die
Schaltfläche [Yes] (Ja) erscheint, klicken Sie auf [Yes] (Ja), um die Installation fortzusetzen.
Wenn Sie nicht fortfahren können, klicken Sie auf [OK] und wiederholen Sie Treiberinstallation
von Schritt 1 an.
11.Um die Installation zu beginnen, klicken Sie noch einmal auf [Weiter]. Die Installation beginnt dann.
Das Dialogfeld “Setup ist jetzt bereit, die Treiber zu installieren” erscheint.
Jetzt kann der Treiber installiert werden.
Operation of the UM-1EX
12.
Stellen Sie den UM-1EX’s ADVANCED (mode select) Switch auf ON.
*
Der Treiber kann mit dem folgenden Verfahren nicht installiert werden, wenn der Schalter auf OFF steht.
Wenn Sie Windows 98/Me/2000/XP oder XP SP1 verwenden, müssen sie den Schalter ADVANCED
(Erweitert) (Moduswahl) auf ON stellen, bevor Sie UM-1EX an Ihren Computer anschließen.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation of the UM-1EX
13.
Schließen Sie den UM-1EX an Ihren Computer an.
Die Meldung “Neue Hardware gefunden” wird angezeigt. Bitte warten Sie.
*
Dieses Gerät ist mit einem Schutzschaltkreis ausgestattet. Nach dem Anschluss des UM-1EX benötigt das
Gerät eine kurze Zeitspanne von einigen Sekunden, bis es den normalen Betrieb aufnimmt.
Windows XP:
1. Das Dialogfeld “Assistent Neue Hardware gefunden” erscheint.
Wenn die Meldung “Mit Windows Update verbinden, um neue Software zu suchen?”
erscheint, wählen Sie “Nein” und klicken auf [Weiter].
besten Treiber für diese Quelle suchen” und klicken Sie auf [Weiter].
Wenn “Treibersignaturoptionen” in Schritt 4 anders lauten als “Ignorieren,” erscheint ein
Dialogfeld mit “!”. Klicken Sie auf [Installation fortsetzen] um mit der Installation
fortzufahren.
Windows 2000:
Wenn “Treibersignaturoptionen” in Schritt 4 anders lauten als “Ignorieren,” erscheint ein
Dialogfeld mit “Digital Signature Not Found” (Digitalsignatur nicht gefunden). Klicken Sie
auf [Ja], um mit der Installation fortzufahren.
14.Es erscheint die Dialogbox Abschließen der Installation neuer Hardware.
Klicken Sie auf [Fertig stellen].
15.Klicken Sie in der Dialogbox Treiber-Setup auf [Schließen].
Dies schließt die Treiberinstallation ab.
Wenn die Dialogbox Systemeigenschaften ändern erscheint, klicken Sie auf [Ja]. Windows
startet automatisch neu.
*
Wenn Sie die Einstellungen der “Treibersignaturoptionen” (Schritt 4 S. 48) geändert haben, stellen Sie
wieder die ursprünglichen Einstellungen her, nachdem Windows neu gestartet hat.
Um sicherzustellen, dass die MIDI-Verarbeitung reibungslos erfolgt, müssen Sie Einstellungen
vornehmen, so dass der Hintergrundverarbeitung Priorität eingeräumt wird.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Herstellung der Verbindung und
Installation der Treiber (Macintosh)
Treiberinstallation und Einstellungen
Mac OS X-Anwender
■ Installation des Treibers
*
Geben Sie in das eventuell erscheinende Dialogfeld “Authenticate” (Authentifizierung) das Kennwort ein und
klicken Sie auf “OK”.
*
Die tatsächliche Anzeige auf Ihrem Macintosh-Bildschirm kann anders aussehen. Das hängt von Ihrer Computer-
Umgebung und Ihrem Betriebssystem ab.
1. Starten Sie Macintosh bei nicht angeschlossenem UM-1EX.
*
Lösen Sie alle USB-Kabel außer der USB-Tastatur und der USB-Maus von Ihrem Computer und starten Sie den
Macintosh neu.
2. Beenden Sie alle aktuell ausgeführten Programme (Anwendungen).
3. Halten Sie die CD-ROM bereit.
Legen Sie die CD-ROM in das CD-ROM-Laufwerk Ihres Macintosh ein.
*
Eine Meldung wie “This Installer package needs to...” (Dieses Installationspaket muss...) wird eventuell angezeigt.
Klicken Sie auf “Continue” (Weiter).
5. In der Anzeige erscheint “Welcome to the EDIROL UM-1Driver Installer” (Willkommen beim EDIROL
UM-1Treiber-Installationsprogramm). Klicken Sie auf [Continue] (Weiter).
6. In der Anzeige erscheint “Select a Destination” (Installationsziel auswählen).
Wählen Sie mit einem Mausklick das Laufwerk aus, auf dem das System installiert ist, und klicken Sie
dann auf [Continue] (Weiter).
*
Wählen Sie Ihre Bootplatte als Laufwerk.
7. In der Anzeige erscheint “Easy Install” (einfache Installation).
Klicken Sie auf [Install] oder [Upgrade].
8. In der Anzeige erscheint “Installing this software requires you to restart your computer when the
installation is done” (Neustart nach Installation erforderlich).
Klicken Sie auf [Continue Installation] (Installation fortsetzen).
9. In der Anzeige erscheint “The software was successfully installed” (Die Software wurde erfolgreich installiert).
Klicken Sie auf [Restart], um Ihren Macintosh neu zu starten.
Damit ist die Installation des UM-1-Treibers abgeschlossen.
Nehmen Sie als Nächstes die MIDI-Geräteeinstellungen vor. (→“Konfiguration des Treibers” (S. 52))
51
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Konfiguration des Treibers
Im folgenden werden die Einstellungen beschrieben, die die Verwendung des UM-1EX mit
Sequenzsoftware unter Verwendung der Standardgeräteeinstellungen von Macintosh ermöglicht.
Wenn Sie eine Sequenzsoftware verwenden, die keine Macintosh Standardgeräteeinstellungen
verwendet, nehmen Sie die Geräteeinstellungen mit der Sequenzsoftware vor.
*
Die tatsächliche Anzeige auf Ihrem Macintosh-Bildschirm kann anders aussehen. Das hängt von Ihrer
Computer-Umgebung und Ihrem Betriebssystem ab.
Operation of the UM-1EX
1.
Stellen Sie den UM-1EX ADVANCED (mode select) Switch auf die
Position ON (EIN).
Operation of the UM-1EX
2.
Schließen Sie den UM-1EX an Ihren Macintosh an.
*
*
Verbinden Sie das Kabel mit dem USB-Stecker des Macintosh und nicht mit dem USB-Stecker der Tastatur.
Dieses Gerät ist mit einem Schutzschaltkreis ausgestattet. Nach dem Anschluss des UM-1EX benötigt
das Gerät eine kurze Zeitspanne von einigen Sekunden, bis es den normalen Betrieb aufnimmt.
3. Öffnen Sie den Ordner Anwendungen auf Ihrer Macintosh-Festplatte. Klicken Sie im Ordner
Dienstprogramme auf Audio MIDI Setup, um das Dialogfeld Audio MIDI Setup zu öffnen.
Klicken Sie auf MIDI
Devices (MIDI Geräte)
4
Klicken Sie auf Add Device
(Gerät hinzufügen)
6
Klicken Sie auf Show Info
(Info anzeigen)
7
4. Klicken Sie auf die Registerkarte MIDI Devices (MIDI-Geräte).
5. Bestätigen Sie, dass UM-1 im Dialogfeld Audio MIDI Setup erscheint.
*
Wenn UM-1 nicht erscheint oder grau angezeigt wird, bedeutet dies, dass der UM-1EX nicht richtig
erkannt wird. Klicken Sie auf Rescan MIDI (MIDI neu scannen). Versuchen Sie auch den Anschluss des
UM-1EX zu trennen und wieder anzuschließen.
*
Vorherige Einstellungen einer anderen Treiber-Version können erhalten bleiben. Klicken Sie dann auf das
grau angezeigte UM-1 oder EDIROL UM-1, um es auszuwählen und klicken Sie dann auf Remove
Selected Device (Ausgewähltes Gerät entfernen), um die Einstellungen zu löschen.
6. Klicken Sie auf Add Device (Gerät hinzufügen). Es erscheint
new external device (neues externes Gerät).
52
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Stellen Sie den Laufwerknamen ein.
1. Nach Auswahl des neuen externen Geräts klicken Sie auf Show Info. (Info anzeigen).
2. Geben Sie den Namen in das Feld Device Name (Gerätename) ein.
8. Verbinden Sie die Symbole ▼ und ▲ (sie bedeuten Ausgaben und Eingaben) des UM-1 Symbols
mit denen des Symbols für das neue externe Gerät und verwenden Sie die Maus, um die Symbole
zu ziehen.s
Verwenden Sie zum
Ziehen die Maus
9. Bei Mac OS X v10.3 oder früher: Schließen Sie das Dialogfeld Audio MIDI Setup. Die
Einstellungen wurden abgeschlossen.
Bei Mac OS X v10.3 oder später: Bestätigen Sie, das MIDI fehlerfrei übertragen und empfangen
wird. Führen Sie die Schritte 10–13 aus (S. 54).
53
Download from Www.Somanuals.com. All Manuals Search And Download.
10.Klicken Sie auf Test
Setup.
Die Form des Cursors
ändert sich
.
11.Klicken Sie auf den in
der Abbildung gezeigten
Bereich. Wenn die MIDI
OUT Anzeige des UM-
1EX zu blinken beginnt,
sind die Einstellungen
korrekt.
Test Setup
10, 12
Verwenden Sie zum
Ziehen die Maus
12.Klicken Sie auf Test
Setup und schließen Sie
die Bestätigung ab.
Klicken Sie auf das Symbol
11
13.Schließen Sie das Dialogfeld Audio MIDI Setup.
.
Bei Verwendung des UM-1EX mit Ihrer Sequenzsoftware
Beachten Sie vor Verwendung des UM-1EX mit Ihrer Sequenzsoftware bitte folgende Punkte.
• Schließen Sie den UM-1EX an Ihren Macintosh an, bevor Sie Ihre Sequenzsoftware starten.
• Trennen Sie nicht den UM-1EX vom Macintosh, während die Sequenzsoftware läuft.
Beenden Sie die Ausführung der Sequenzsoftware bevor Sie den UM-1EX von Ihrem
Macintosh trennen.
• Deaktivieren Sie die Ruhefunktion Ihres Macintosh.
• Der UM-1EX funktioniert nicht in der Mac OS X Classic Umgebung. Verwenden Sie den UM-
1EX, wenn die Classic Umgebung nicht läuft.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Connexion et installation des pilotes (Windows)
Installation du pilote
Windows XP/2000
1. Avant de connecter l’UM-1EX, démarrez Windows.
Ne connectez pas l’UM-1EX avant d’avoir atteint l’étape 13 (p. 57).
*
*
Débranchez tous les câbles USB, sauf ceux du clavier USB ou de la souris USB, le cas échéant.
Ouvrez une session Windows en tant qu’utilisateur doté de droits d’administration (Administrateur, par exemple).
2. Ouvrez la boîte de dialogue Propriétés Système.
Windows XP :
1. Cliquez sur le bouton Démarrer de Windows et sélectionnez Panneau de configuration dans
le menu.
2. Dans “Choisissez une catégorie”, cliquez sur “Performances et maintenance”.
3. Dans “ou choisissez une icône du Panneau de configuration”, cliquez sur l’icône Système.
Selon la configuration de l’ordinateur, il se peut que l’icône Système apparaisse dans le
Panneau de configuration (vue classique). Si c’est le cas, double-cliquez sur l’icône Système.
Windows 2000 :
1. Cliquez sur le bouton Démarrer de Windows et sélectionnez Paramètres | Panneau de
configuration.
2. Dans le Panneau de configuration, double-cliquez sur l’icône Système.
3. Cliquez sur l’onglet Matériel, puis sur [Signature du pilote].
La boîte de dialogue Options de signature du pilote s'affiche.
4. Dans la boîte de dialogue Options de signature du pilote, sélectionnez “Ignorer”, puis cliquez
sur [OK].
Si le paramètre sélectionné est “Avertir” ou “Bloquer”, modifiez-le et choisissez “Ignorer”.
Lorsque vous avez terminé d’installer le pilote, revenez au paramètre d’origine.
5. Cliquez sur [OK] pour fermer la boîte de dialogue Propriétés Système.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Fermez tous les logiciels (applications) actifs.
Fermez également toutes les fenêtres ouvertes, s’il y en a. Si vous utilisez un programme antivirus
ou des logiciels similaires, fermez-les également.
7. Munissez-vous du CD-ROM.
Insérez le CD-ROM dans le lecteur de l’ordinateur.
*
Si le message “Windows peut effectuer la même action chaque fois que vous insérez un
disque ou connectez un périphérique avec ce type de fichier” apparaît, cliquez sur [Annuler].
8. Cliquez sur le bouton Démarrer de Windows et sélectionnez l’option Exécuter...
9. Dans le champ “Ouvrir” de la boîte de dialogue “Exécuter...”, saisissez l’adresse ci-dessous et
cliquez sur [OK].
D: \Driver\XP2k\setup.exe
*
Dans cet exemple, le nom du lecteur est “D:” mais il est possible qu’il soit différent sur votre ordinateur.
Utilisez la lettre correspondant à votre lecteur de CD-ROM.
Cliquez sur [Suivant].
Windows XP :
Si les “Options de signature du pilote” (étape 4) ont été définies sur un paramètre autre que
“Ignorer”, une boîte de dialogue affichant un symbole “!” ou “x” apparaît. Si un bouton
[Continuer] apparaît, cliquez dessus pour poursuivre l’installation. S’il vous est impossible de
continuer, cliquez sur [OK] et recommencez l’installation du pilote depuis le début.
Windows 2000 :
Si les “Options de signature du pilote” (étape 4) ont été définies sur un paramètre autre que
“Ignorer”, une boîte de dialogue indiquant “Signature numérique non trouvée” apparaît. Si
un bouton [Oui] apparaît, cliquez dessus pour poursuivre l’installation. S’il vous est impossible
de continuer, cliquez sur [OK] et recommencez l’installation du pilote depuis le début.
11.Cliquez une nouvelle fois sur [Suivant] pour lancer l’installation. L’installation commence.
Une boîte de dialogue apparaît pour vous indiquer que “le système est prêt à installer les
pilotes”.
Vous pouvez donc lancer l’installation du pilote.
Operation of the UM-1EX
12.
Placez le ADVANCED (mode select) Switch de l’UM-1EX sur ON.
*
Si ce commutateur reste sur OFF, vous ne pourrez pas installer le pilote avec la procédure suivante.
Si vous utilisez Windows 98/Me/2000/XP ou XP SP1, vous devez placer le commutateur
mode AVANCÉ (sélecteur de mode) sur ON avant de connecter l’UM-1EX à votre ordinateur.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation of the UM-1EX
13.
Connectez l’UM-1EX à votre ordinateur.
Le message “Nouveau matériel détecté” s’affiche. Veuillez patienter.
*
Cet appareil est équipé d’un circuit de protection. Après avoir connecté l’UM-1EX, il est nécessaire
d’attendre quelques secondes avant que l’appareil ne fonctionne normalement.
Windows XP :
1. La boîte de dialogue Assistant ajout de nouveau matériel s’affiche.
Si le système vous demande si “vous souhaitez vous connecter à Windows Update pour
rechercher le pilote?”, choisissez “Non” et cliquez sur [Suivant].
pilote dans ces emplacements” et cliquez sur [Suivant].
Si les “Options de signature du pilote” (étape 4) ont été définies sur un paramètre autre que
“Ignorer”, une boîte de dialogue affichant un symbole “!” apparaît. Cliquez sur [Continuer]
pour poursuivre l’installation.
Windows 2000 :
Si les “Options de signature du pilote” (étape 4) ont été définies sur un paramètre autre que
“Ignorer”, une boîte de dialogue indiquant “Signature numérique non trouvée” apparaît.
Cliquez sur [Oui] pour poursuivre l’installation.
14.La boîte de dialogue Fin de l'Assistant Ajout de nouveau matériel détecté s’affiche.
Cliquez sur [Terminer].
15.Dans la boîte de dialogue Installation du pilote, cliquez sur [Fermer].
L’installation du pilote est alors terminée.
Si la boîte de dialogue Modifier les paramètrs système s’affiche, cliquez sur [Oui]. Windows
redémarre automatiquement.
*
Si vous avez modifié les “options de signature du pilote” (étape 4, p. 55), rétablissez les options
d’origine après le redémarrage de Windows.
Ensuite, pour garantir que les signaux audio et MIDI seront correctement traités, paramétrez le
système de manière à donner la priorité aux services d’arrière-plan.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Connexion et installation des pilotes (Macintosh)
Installation et configuration du pilote
Mac OS X
■ Installation du pilote
*
Si la boîte de dialogue “Authentifier” apparaît pendant l’installation, saisissez le mot de passe et cliquez sur “OK”.
*
Il se peut que votre écran affiche des informations légèrement différentes, selon votre environnement et le
système d’exploitation que vous utilisez.
1. Avant de connecter l’UM-1EX, démarrez votre Macintosh.
Débranchez tous les câbles USB, à l’exception de ceux du clavier et de la souris, puis redémarrez l’ordinateur.
*
2. Fermez tous les logiciels (applications) actifs.
3. Munissez-vous du CD-ROM.
Introduisez le CD-ROM dans le lecteur de l’ordinateur.
*
Il se peut que le système vous indique que “ce package d’installation a besoin de (...)”.
Cliquez sur “Continuer”..
5. Un message de “bienvenue dans l’Assistant d’installation du pilote de l’EDIROL UM-1” s’affiche.
Cliquez sur [Continuer].
6. L’écran indique “Sélectionnez une destination”.
Cliquez sur le lecteur sur lequel est installé le système d’exploitation, puis cliquez sur [Continuer].
Sélectionner le disque de démarrage comme lecteur.
*
7. Le message “Installation standard” s'affiche.
Cliquez sur [Installer] ou sur [Mettre à niveau].
8. Le message vous signale que “vous devrez redémarrer votre ordinateur à la fin de l’installation du logiciel”.
Cliquez sur [Continuer l’installation]..
9. Un message doit vous indiquer que “l’installation du logiciel a réussi”.
Cliquez sur [Redémarrer] pour redémarrer l’ordinateur.
L'installation du pilote de l’UM-1 est terminée.
Procédez ensuite au paramétrage des périphériques MIDI. (→“Configuration du pilote” (p. 59))
58
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Configuration du pilote
Vous trouverez ci-dessous les paramètres qui permettent d’utiliser l’UM-1EX avec un logiciel
séquenceur en utilisant le paramétrage Macintosh standard pour les périphériques.
Si vous utilisez un logiciel séquenceur qui n’utilise pas les paramètres de périphériques standard
Macintosh, paramétrez le périphérique à partir du séquenceur.
*
Il se peut que votre écran affiche des informations légèrement différentes, selon votre environnement et le
système d’exploitation que vous utilisez.
Operation of the UM-1EX
1.
2.
Placez le ADVANCED (mode select) Switch de l’UM-1EX sur ON.
Operation of the UM-1EX
Connectez l’UM-1EX à votre ordinateur.
*
*
Branchez le câble au connecteur USB du Macintosh lui-même (et non pas à celui du clavier).
Cet appareil est équipé d’un circuit de protection. Après avoir connecté l’UM-1EX, il est nécessaire
d’attendre quelques secondes avant que l’appareil ne fonctionne normalement.
3. Ouvrez le dossier Applications du disque dur de votre Macintosh. Dans le dossier Utilitaires,
double-cliquez sur Audio MIDI Setup pour ouvrir la boîte de dialogue correspondante.
Cliquez sur Périphériques MIDI
4
Cliquez sur Ajouter
périphérique
6
Cliquez sur Afficher les informations
7
4. Cliquez sur l'onglet Périphériques MIDI.
5. Vérifiez que l’UM-1 apparaît bien dans la boîte de dialogue Audio MIDI Setup.
*
Si l’UM-1 n’apparaît pas ou apparaît en grisé, c’est qu’il n’est pas correctement reconnu par votre système.
Cliquez sur Analyse MIDI. Essayez aussi de débrancher puis de rebrancher l’UM-1EX.
*
Il se peut que les paramètres d’installation d’une version antérieure du pilote soient restés dans le système.
Si c’est le cas, cliquez sur UM-1 ou EDIROL UM-1 (en grisé) pour le sélectionner, puis sur Supprimer le
périphérique sélectionné pour supprimer les paramètres.
6. Cliquez sur Ajouter périphérique. Le message
Nouveau périphérique externe apparaît.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Choisissez le nom du périphérique.
1. Sélectionnez le nouveau périphérique externe, puis cliquez sur Afficher les informations.
2. Saisissez le nom dans le champ Nom du périphérique.
8. Connectez les symboles ▼ et ▲ (qui signalent les entrées et les sorties) de l’icône de l’UM-1 à ceux
de l’icône du nouveau périphérique externe en utilisant la souris pour tracer les connexions.s
Utilisez la souris pour
tracer les connexions
9. Si vous utilisez Mac OS X v10.3 ou antérieure : Fermez la boîte de dialogue Audio MIDI Setup.
La configuration est terminée.
Si vous utilisez Mac OS X v10.3 ou ultérieure : Vérifiez que les signaux MIDI sont transmis et
reçus correctement. Suivez les étapes 10 à 13 (p. 61).
60
Download from Www.Somanuals.com. All Manuals Search And Download.
10.Cliquez sur Test Setup.
Le curseur change de
forme
.
11.Cliquez sur la zone
indiquée sur
Test Setup
10, 12
l’illustration. Si le voyant
MIDI OUT de l’UM-1EX
clignote, c’est que les
paramètres sont corrects.
Utilisez la souris pour
tracer les connexions
12.Cliquez sur Test Setup
et terminez la
confirmation.
Cliquez sur l’icône
11
13.Fermez la boîte de dialogue Audio MIDI Setup.
.
Utilisation de l’UM-1EX avec un logiciel séquenceur
Avant d’utiliser l’UM-1EX avec un logiciel séquenceur, respectez les points suivants :
• Connectez l’UM-1EX à votre Macintosh avant de démarrer votre logiciel séquenceur.
• Ne débranchez pas l’UM-1EX de votre ordinateur tant que votre logiciel séquenceur est
ouvert.
Quittez le logiciel avant de débrancher l’UM-1EX de votre ordinateur.
• Désactivez la fonction de veille de votre Macintosh.
• L’UM-1EX ne fonctionne pas sous Mac OS X Classic. Utilisez l’UM-1EX uniquement si
l'environnement Classic n’est pas ouvert.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Collegamento e installazione dei driver (Windows)
Installazione del driver
Utenti Windows XP/2000
1. Avviare Windows con l’UM-1EX scollegato.
Non collegare l’UM-1EX al computer fino al passo 13 (p. 64).
*
*
Scollegare tutti i cavi USB, ad eccezione della tastiera e del mouse USB, se utilizzati.
Accedere a Windows utilizzando un nome utente con privilegi amministrativi, ad esempio Administrator.
2. Aprire la finestra di dialogo Proprietà del sistema.
Windows XP:
1
2
3
Dal menu di avvio di Windows scegliere Pannello di controllo.
In “Scegliere una categoria” fare clic su “Prestazioni e manutenzione”.
In “o un’icona del Pannello di controllo” fare clic sull’icona Sistema.
A seconda della configurazione del sistema, l’icona Sistema potrebbe essere visualizzata
direttamente nel Pannello di controllo (visualizzazione classica). In questo caso, fare doppio
clic sull’icona Sistema.
Windows 2000:
1
2
Dal menu di avvio di Windows scegliere Impostazioni | Pannello di controllo.
In Pannello di controllo fare doppio clic sull’icona Sistema.
3. Fare clic sulla scheda Hardware e quindi su [Firma driver].
Verrà visualizzata la finestra di dialogo Opzioni firma driver.
4. Nella finestra di dialogo Opzioni firma driver, selezionare l’opzione “Ignora”, poi fare clic su [OK].
Se l’impostazione corrente è “Avvisa” o “Blocca,” modificarla su “Ignora”. Al termine
dell’installazione del driver, ripristinare l’impostazione originale.
5. Fare clic su [OK] per chiudere la finestra di dialogo Proprietà del sistema.
6. Chiudere tutti i programmi in esecuzione.
Chiudere inoltre tutte le finestre aperte. Se si utilizza un antivirus o un programma simile,
chiuderlo.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Preparare il CD-ROM.
Inserire il CD-ROM nell’apposita unità del computer.
*
Se viene visualizzato il messaggio “È possibile eseguire la stessa operazione ogni volta che si
inserisce un disco o che si connette una periferica con il seguente tipo di file” fare clic su
[Annulla].
8. Scegliere Esegui… dal menu di avvio di Windows.
9. Nel campo Apri della finestra di dialogo “Esegui” immettere la seguente stringa e quindi fare clic
su [OK].
D: \Driver\XP2k\setup.exe
*
L’identificativo dell’unità è “D:” nell’esempio riportato qui, ma potrebbe essere diverso sul sistema
utilizzato. Utilizzare la lettera corrispondente all’unità CD-ROM in uso.
Fare clic su [Avanti].
Windows XP:
Se “Opzioni firma driver” al passo 4 è impostato su “Ignora” verrà visualizzata una finestra di
dialogo con il simbolo “!” o “x” Se viene visualizzato un pulsante [Continua], fare clic su
[Continua] per procedere con l’installazione. Se non è possibile continuare, fare clic su [OK] e
ripetere l’installazione del driver dal passo 1.
Windows 2000:
Se “Opzioni firma driver” al passo 4 è impostato su “Ignora” verrà visualizzata la finestra di
dialogo “Firma digitale non trovata” Se viene visualizzato un pulsante [Sì], fare clic su [Sì]
per procedere con l’installazione. Se non è possibile continuare, fare clic su [OK] e ripetere
l’installazione del driver dal passo 1.
11.Per avviare l’installazione, fare di nuovo clic su [Avanti] L’installazione avrà inizio.
Verrà visualizzata la finestra di dialogo “Setup is now ready to install the drivers”.
Ora è possibile installare il driver.
Operation of the UM-1EX
12.
Spostare l’ADVANCED (mode select) Switch dell’UM-1EX sulla posizione ON.
*
Il driver non può essere installato seguendo la procedura sotto indicata se l’interruttore è impostato su OFF.
Se si utilizza Windows 98/Me/2000/XP o XP SP1, è necessario impostare l’interruttore
ADVANCED (selezione del modo) in posizione ON prima di collegare l’UM-1EX al computer.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation of the UM-1EX
13.
Collegare l’UM-1EX al computer.
Viene visualizzato il messaggio “Installazione guidata nuovo hardware”. Attendere qualche
minuto.
*
Questo apparecchio è provvisto di un circuito di protezione. È necessario attendere qualche secondo dopo
aver collegato l’UM-1EX prima che l’apparecchio funzioni normalmente.
Windows XP:
1
2
Appare la finestra di dialogo Installazione guidata nuovo hardware.
Se viene visualizzato il messaggio “Consentire la connessione a Windows Update per la
ricerca di software?”, scegliere “No” e quindi fare clic su [Avanti].
Verificare che “EDIROL UM-1” sia visualizzato. quindi scegliere “Ricerca il miglior driver
disponibile in questi percorsi” e fare clic su [Avanti].
Se “Opzioni firma driver” al passo 4 è impostato su “Ignora” verrà visualizzata una finestra di
dialogo con il simbolo “!”. Fare clic su [Continua] per procedere con l’installazione.
Windows 2000:
Se “Opzioni firma driver” al passo 4 è impostato su “Ignora” verrà visualizzata la finestra di
dialogo “Firma digitale non trovata”. Fare clic su [Sì] per procedere con l’installazione.
14.Verrà visualizzata la finestra di dialogo Completamento dell’Installazione guidata nuovo
hardware in corso.
Fare clic su [Fine].
15.Nella finestra di dialogo Installazione driver fare clic su [Chiudi].
L’installazione del driver è completata.
Se viene visualizzata la finestra di dialogo Modifica delle impostazioni di sistema, scegliere [Sì].
Windows verrà riavviato automaticamente.
*
Se è stata modificata l’impostazione nella finestra “Opzioni firma driver” (punto 4 a p. 62), ripristinare
l’impostazione originale dopo il riavvio di Windows.
Per garantire che l’elaborazione del MIDI venga eseguita correttamente, è necessario dare priorità
ai servizi in background effettuando le impostazioni appropriate.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Collegamento e installazione dei driver (Macintosh)
Installazione e configurazione dei driver
Utenti Mac OS X
■ Installazione del driver
*
Se durante l’installazione viene visualizzata la finestra di dialogo “Authenticate”, inserire la password e
fare clic su “OK”.
*
La schermata visualizzata potrebbe variare a seconda dell’ambiente e del sistema operativo installato.
1. Accendere il Macintosh con l’UM-1EX scollegato.
Scollegare tutti i cavi USB ad eccezione di quelli della tastiera e del mouse e riavviare il Macintosh.
*
2. Chiudere tutti i programmi in esecuzione.
3. Preparare il CD-ROM.
Inserire il CD nell’apposita unità del Macintosh.
*
È possibile che venga visualizzato un messaggio simile a “This Installer package needs to...”
Fare clic su “Continua”.
5. Sullo schermo comparirà il seguente messaggio: “Welcome to the EDIROL UM-1Driver Installer”.
Fare clic su [Continua].
6. Sullo schermo verrà visualizzato il messaggio: “Select a Destination”.
Selezionare l’unità in cui è installato il sistema operativo e fare clic su [Continua].
*
Selezionare il disco di avvio come unità.
7. Verrà visualizzato il messaggio “Installazione Standard”.
Fare clic su [Installa] o [Upgrade].
8. Verrà visualizzato il messaggio “Installing this software requires you to restart your computer
when the installation is done.”
Fare clic su [Continua installazione].
9. Verrà visualizzato il messaggio “The software was successfully installed”.
Fare clic su [Riavvia] per riavviare il Macintosh.
La procedura d’installazione del driver UM-1 è giunta al termine.
Successivamente, configurare il dispositivo MIDI. (→“Configurazione del driver” (p. 66))
65
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Configurazione del driver
Di seguito vengono descritte le impostazioni che abilitano l’uso dell’UM-1EX con software
sequencer utilizzando le impostazioni standard di Macintosh.
Se si utilizza un software sequencer che non utilizza le impostazioni standard di Macintosh,
eseguire le impostazioni contenute nel software sequencer.
*
La schermata visualizzata potrebbe variare a seconda dell’ambiente e del sistema operativo installato.
Operation of the UM-1EX
1.
Spostare l’ADVANCED (mode select) Switch dell’UM-1EX sulla posizione ON.
Operation of the UM-1EX
2.
Collegare l’UM-1EX al Macintosh.
*
*
Collegare il cavo al connettore USB del Macintosh, non a quello della tastiera.
Questo apparecchio è provvisto di un circuito di protezione. È necessario attendere qualche secondo dopo
aver collegato l’UM-1EX prima che l’apparecchio funzioni normalmente.
3. Aprire la cartella Applications del disco fisso del Macintosh. Nella cartella Utilities fare doppio
clic su Audio MIDI Setup per aprire la finestra di dialogo Audio MIDI Setup.
Fare clic su MIDI Devices
4
Fare clic su
“Aggiungi dispositivo”
6
Fare clic su Show Info
7
4. Fare clic sulla scheda MIDI Devices.
5. Verificare che UM-1 viene visualizzato nella finestra di dialogo Audio MIDI Setup.
*
Se UM-1 non viene visualizzato o se non è attivo, significa che l’UM-1EX non è stato riconosciuto in modo
corretto. Fare clic su Rescan MIDI. Scollegare e ricollegare l’UM-1EX.
*
Potrebbero essere presenti impostazioni che appartengono a una installazione precedente di una diversa
versione del driver. In questo caso, fare clic su UM-1 o EDIROL UM-1 per selezionarlo e fare clic su
Remove Selected Device per cancellare le impostazioni.
6. Fare clic su Aggiungi Dispositivo. Compare
Nuovo dispositivo esterno.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Impostare il nome del dispositivo.
1
2
Dopo aver selezionato nuovo dispositivo esterno, fare clic su Mostra Info.
Immettere il nome nel campo Device Name.
8. Collegare i simboli ▼ e ▲ (che rappresentano le uscite e le entrate) dell’icona UM-1 a quelli
dell’icona nuovo dispositivo esterno utilizzando il mouse per trascinarli.s
Utilizzare il mouse per
trascinare un collegamento
9. Se si sta utilizzando Mac OS X v10.3 o anteriori: Chiudere la finestra di dialogo Audio MIDI
Setup La procedura di installazione è giunta al termine.
Se si sta utilizzando Mac OS X v10.3 o posteriori: Verificare che la trasmissione e la ricezione
MIDI siano corrette. Eseguire le operazioni descritte ai punti da 10 a 13 (p. 68).
67
Download from Www.Somanuals.com. All Manuals Search And Download.
10.Fare clic su Test Setup.
La forma del cursore del
mouse cambia
.
11.Fare clic sull’area
raffigurata
Test Setup
10, 12
nell’immagine. Se
l’indicatore MIDI OUT
dell’UM-1EX comincia a
lampeggiare, le
Utilizzare il mouse per
trascinare un collegamento
impostazioni sono
corrette.
12.Fare clic su Test Setup e
completare la verifica.
Fare clic sull’icona
11
13.Chiudere la finestra di dialogo Audio MIDI Setup.
Quando si utilizza l’UM-1EX con il software sequencer
Prima di utilizzare l’UM-1EX con il software sequencer, leggere le seguenti indicazioni.
• Collegare l’UM-1EX al Macintosh prima di avviare il software sequencer.
• Non scollegare l’UM-1EX dal Macintosh mentre il software sequencer è in esecuzione.
Chiudere il software sequencer prima di scollegare l’UM-1EX dal Macintosh.
• Disattivare l’opzione Stop del Macintosh.
• L’UM-1EX non funziona in ambiente Classic Mac OS X. Utilizzare l’UM-1EX quando
l’ambiente Classic non è in esecuzione.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexión e instalación de los controladores (Windows)
Instalación del controlador
Usuarios de Windows XP/2000
1. Con el UM-1EX desconectado, inicie Windows.
No conecte el UM-1EX al equipo hasta que llegue al Paso 13 (pág. 71).
*
*
Desconecte todos los cables USB excepto el del teclado USB y el ratón USB (si se utilizan).
Inicie sesión en Windows utilizando un nombre de usuario con privilegios de administrador (como
Administrador).
2. Abra el cuadro de diálogo Propiedades del sistema.
Windows XP:
1. Haga clic en el menú Inicio de Windows y seleccione Panel de control.
2. En “Elija una categoría”, haga clic en “Rendimiento y mantenimiento”.
3. En “o elija un icono del Panel de control”, haga clic en el icono Sistema.
En función de la configuración, puede que el icono Sistema aparezca directamente en el Panel
de control (en la Vista clásica). En este caso, haga doble clic en el icono Sistema.
Windows 2000:
1. Haga clic en el menú Inicio de Windows y seleccione Configuración | Panel de control.
2. En el Panel de control, haga doble clic en el icono Sistema.
3. Haga clic en la ficha Hardware y, a continuación, en [Firma de controladores].
Aparecerá el cuadro de diálogo Opciones de firma del controlador.
4. En el cuadro de diálogo Opciones de firma del controlador, seleccione “Ninguna”, y a
continuación haga clic en [Aceptar].
Si la opción seleccionada es “Advertir” o “Bloquear”, cámbiela a “Ninguna”. A continuación,
cuando haya acabado de instalar el controlador, vuelva a cambiarla a la opción original.
5. Haga clic en [Aceptar] para cerrar el cuadro de diálogo Propiedades del sistema.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Salga de todos los programas de software que esté ejecutando (aplicaciones).
Cierre todas las ventanas que estén abiertas. Si está utilizando un antivirus o software similar,
deberá cerrar todos estos programas.
7. Prepare el CD-ROM.
Inserte el CD-ROM en la unidad de CD-ROM de su PC.
*
Si aparece el mensaje “Windows puede realizar la misma acción cada vez que inserte un disco
o conecte un dispositivo con este tipo de archivo”, haga clic en [Cancelar].
8. En el menú Inicio de Windows, elija Ejecutar....
9. En el campo Abrir del cuadro de diálogo “Ejecutar...”, escriba lo siguiente y haga clic en
[Aceptar].
D: \Driver\XP2k\setup.exe
*
En nombre de la unidad es “D”: en el ejemplo descriptivo mostrado en esta página, pero puede ser otro en su
sistema. Use el nombre de la unidad de CD-ROM.
Haga clic en [Siguiente].
Windows XP:
Si “Opciones de firma del controlador” en el paso 4 es cualquier valor que no sea
“Ninguna”, aparece un cuadro de diálogo con el símbolo “!” o “x”. Si aparece un botón de
[Continuar], haga clic en [Continuar] para proseguir con la instalación. Si no puede continuar,
haga clic en [Aceptar] y repita la instalación del controlador desde el paso 1.
Windows 2000:
Si “Opciones de firma del controlador” en el paso 4 es cualquier valor que no sea
“Ninguna”, aparece un cuadro de diálogo que indica “Firma digital no encontrada”. Si
aparece un botón de [Sí], haga clic en [Sí] para proseguir con la instalación. Si no puede
continuar, haga clic en [Aceptar] y repita la instalación del controlador desde el paso 1.
11.Para comenzar la instalación, haga clic en [Siguiente] de nuevo. Se iniciará la instalación.
Aparecerá el cuadro de diálogo “El programa de instalación está preparado para instalar el
controlador”.
Ahora puede instalar el controlador.
Operation of the UM-1EX
12.
Coloque el UM-1EX ADVANCED (mode select) Switch en ON.
*
El controlador no se puede instalar mediante el siguiente procedimiento si el interruptor está en OFF.
Si está utilizando Windows 98/Me/2000/XP o XP SP1, debe encender el Interruptor de
selección del modo ADVANCED antes de conectar el UM-1EX al ordenador.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation of the UM-1EX
13.
Conecte el UM-1EX al ordenador.
Aparecerá un mensaje de “Hardware nuevo encontrado”. Espere.
*
Esta unidad está provista de un circuito de protección. Es necesario dejar pasar un pequeño intervalo (de
unos segundos) después de conectar el UM-1EX para que la unidad funcione correctamente.
Windows XP:
1. Aparecerá el cuadro de diálogo del Asistente para hardware nuevo encontrado.
Si aparece el mensaje “¿Conectar a Windows Update para buscar software?”, elija “No” y a
continuación haga clic en [Siguiente].
2. Asegúrese de que se indica “EDIROL UM-1”. A continuación, seleccione “Buscar mejor
controlador en estas ubicaciones” y haga clic en [Siguiente].
Si “Opciones de firma del controlador” en el paso 4 es cualquier valor que no sea “Ninguna”,
aparecerá un cuadro de diálogo con el símbolo “!”. Haga clic en [Continuar] para proseguir con
la instalación.
Windows 2000:
Si “Opciones de firma del controlador” en el paso 4 es cualquier valor que no sea
“Ninguna”, aparece un cuadro de diálogo que indica “Firma digital no encontrada”. Haga
clic en [Sí] para proseguir con la instalación.
14.Aparecerá el cuadro de diálogo finalización del Asistente para hardware nuevo encontrado.
Haga clic en [Finalizar].
15.En el cuadro de diálogo Configuración del controlador, haga clic en [Cerrar].
Con esto finaliza la instalación del controlador.
Si aparece el cuadro de diálogo Cambio de configuración del sistema, haga clic en [Sí].
Windows se reiniciará automáticamente.
*
Si ha cambiado la configuración de “Opciones de firma de controlador” (paso 4 en pág. 69),
restablezca la configuración original después de reiniciar Windows.
A continuación, para asegurar que el procesamiento de MIDI se produce sin problemas, deberá
realizar la configuración de forma que los Servicios en segundo plano tengan prioridad.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Conexión e instalación de los controladores (Macintosh)
Instalación del controlador y ajustes
Usuarios de Mac OS X
■ Instalación del controlador
*
Si aparece el cuadro de diálogo “Authenticate” durante la instalación, introduzca la contraseña y haga clic en “OK”.
*
En la pantalla del Macintosh podrá aparecer información diferente, en función de su entorno informático y
del sistema operativo que esté utilizando.
1. Con el UM-1EX desconectado, inicie Macintosh.
Desconecte todos los cables USB, excepto los del teclado o del ratón, e inicie el sistema.
*
2. Salga de todos los programas de software que esté ejecutando (aplicaciones).
3. Prepare el CD-ROM.
Inserte el CD-ROM en la unidad de CD-ROM del Macintosh.
*
Es posible que aparezca un mensaje parecido a “El paquete del programa de instalación necesita...”.
Haga clic en “Continuar”.
5. Aparecerá el mensaje “Welcome to the EDIROL UM-1Driver Installer.” Haga clic en [Continue].
6. La pantalla indicará “Select a Destination”.
Haga clic en la unidad en la que está instalado el sistema operativo y, a continuación, haga clic en [Continue].
Seleccione el disco de inicio como la unidad.
*
7. La pantalla indicará “Easy Install”.
Haga clic en [Install] o [Upgrade].
8. La pantalla indicará “Installing this software requires you to restart your computer when the
installation is done”.
Haga clic en [Continue Installation].
9. La pantalla indicará “The software was successfully installed”.
Haga clic en [Restart] para reiniciar el Macintosh.
Con esto finaliza la instalación del controlador de UM-1.
A continuación, configure los dispositivos MIDI. (→“Configuración del controlador” (pág. 73))
72
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Configuración del controlador
A continuación se describen los ajustes que permiten el uso del UM-1EX con software del
secuenciador mediante ajustes de dispositivos estándares de Macintosh.
Si está utilizando un software de secuenciador que no utilice los ajustes de dispositivo estándar de
Macintosh, realice la configuración del dispositivo dentro del software del secuenciador.
*
En la pantalla del Macintosh podrá aparecer información diferente, en función de su entorno informático y
del sistema operativo que esté utilizando.
Operation of the UM-1EX
1.
2.
Coloque el ADVANCED (mode select) Switch del UM-1EX en la posición ON.
Operation of the UM-1EX
Conecte el UM-1EX al Macintosh.
*
*
Conecte el cable al conector USB del propio Macintosh, no al conector USB del teclado.
Esta unidad está provista de un circuito de protección. Es necesario dejar pasar un pequeño intervalo (de
unos segundos) después de conectar el UM-1EX para que la unidad funcione correctamente.
3. Abra la carpeta Applications de su disco duro. En la carpeta Utilities, haga doble clic en Audio
MIDI Setup para abrir el cuadro de diálogo Audio MIDI Setup.
Haga clic en MIDI Devices
4
Haga clic en Add Device
6
Haga clic en Show Info
7
4. Haga clic en la ficha MIDI Devices.
5. Confirme que UM-1 aparece en el cuadro de diálogo Audio MIDI Setup.
*
Si UM-1 no aparece o aparece en gris, significa que no se está reconociendo correctamente el UM-1EX. Haga
clic en Rescan MIDI. Intente desconectar y volver a conectar el UM-1EX.
*
Puede que permanezcan los ajustes anteriores de la instalación de una versión diferente del controlador. Si es
así, haga clic en UM-1 que aparece en gris o en EDIROL UM-1 para seleccionarlo, y a continuación haga
clic en Remove Selected Device para eliminar los ajustes.
6. Haga clic en Add Device. Aparecerá
New external device.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Introduzca el nombre en device name.
1. Una vez seleccionado new external device, haga clic en Show Info.
2. Introduzca el nombre en el campo Device Name.
8. Conecte los símbolos ▼ y ▲ (que representan las salidas y entradas) del icono UM-1 a los del icono
new external device utilizando el ratón para arrastrarlos entre ellos.s
Utilice el ratón para
arrastrar una conexión
9. Si está utilizando Mac OS X v10.3 o una versión anterior: Cierre el cuadro de diálogo Audio
MIDI Setup. De este modo se completan los ajustes.
Si está utilizando Mac OS X v10.3 o una versión posterior: Confirme que MIDI se está
transmitiendo y recibiendo correctamente. Realice los pasos 10–13 (pág. 75).
74
Download from Www.Somanuals.com. All Manuals Search And Download.
10.Haga clic en Test Setup.
Cambia la forma del
cursor del ratón
.
11.Haga clic en el área que
se muestra en la
Test Setup
10, 12
ilustración. Si el
indicador MIDI OUT del
UM-1EX comienza a
parpadear, los ajustes
son correctos.
Utilice el ratón para
arrastrar una conexión
12.Haga clic en Test Setup
y finalice la
confirmación.
Haga clic en el icono
11
13.Cierre el cuadro de diálogo Audio MIDI Setup.
.
Cuando utilice el UM-1EX con su software de secuenciador
Antes de utilizar el UM-1EX con su software de secuenciador, tenga en cuenta los siguientes puntos.
• Conecte el UM-1EX al Macintosh antes de iniciar el software de secuenciador.
• No desconecte el UM-1EX del Macintosh mientras se esté ejecutando el software del
secuenciador.
Salga del software del secuenciador antes de desconectar el UM-1EX del Macintosh.
• Desactive la función de modo de suspensión del Macintosh.
• El UM-1EX no funcionará en el entorno Classic de Mac OS X. Utilice el UM-1EX cuando no se
esté ejecutando el entorno Classic.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
When you need repair service, call your nearest EDIROL/Roland Service Center or authorized
EDIROL/Roland distributor in your country as shown below.
Information
SOUTH AFRICA
MALAYSIA/
ECUADOR
CENTRAL/LATIN
AMERICA
Paul Bothner(PTY)Ltd.
Royal Cape Park, Unit 24
Londonderry Road, Ottery 7800
Cape Town, SOUTH AFRICA
TEL: (021) 799 4900
Mas Musika
SINGAPORE
Rumichaca 822 y Zaruma
Guayaquil - Ecuador
TEL:(593-4)2302364
Roland Asia Pacific Sdn. Bhd.
45-1, Block C2, Jalan PJU 1/39,
Dataran Prima, 47301 Petaling
Jaya, Selangor, MALAYSIA
TEL: (03) 7805-3263
EUROPE
EDIROL (Europe) Ltd.
Studio 3.4 114 Power Road
London W4 5PY
ARGENTINA
Instrumentos Musicales S.A.
Av.Santa Fe 2055
GUATEMALA
Casa Instrumental
Calzada Roosevelt 34-01,zona 11
Ciudad de Guatemala
Guatemala
U. K.
ASIA
(1123) Buenos Aires
ARGENTINA
TEL: (011) 4508-2700
TEL: +44 (0)20 8747 5949
FAX:+44 (0)20 8747 5948
PHILIPPINES
CHINA
G.A. Yupangco & Co. Inc.
339 Gil J. Puyat Avenue
Makati, Metro Manila 1200,
PHILIPPINES
Roland Shanghai Electronics
Co.,Ltd.
TEL:(502) 599-2888
BARBADOS
Deutschland
TEL: 0700 33 47 65 20
France
TEL: 0810 000 371
Italia
5F. No.1500 Pingliang Road
Shanghai 200090, CHINA
TEL: (021) 5580-0800
A&B Music Supplies LTD
12 Webster Industrial Park
Wildey, St.Michael, Barbados
TEL: (246)430-1100
HONDURAS
TEL: (02) 899 9801
Almacen Pajaro Azul S.A. de C.V.
BO.Paz Barahona
TAIWAN
Roland Shanghai Electronics
Co.,Ltd.
(BEIJING OFFICE)
10F. No.18 3 Section Anhuaxili
Chaoyang District Beijing
100011 CHINA
3 Ave.11 Calle S.O
San Pedro Sula, Honduras
TEL: (504) 553-2029
ROLAND TAIWAN
ENTERPRISE CO., LTD.
Room 5, 9fl. No. 112 Chung
Shan N.Road Sec.2, Taipei,
TAIWAN, R.O.C.
TEL: 02 93778329
BRAZIL
Roland Brasil Ltda.
Rua San Jose, 780 Sala B
Parque Industrial San Jose
Cotia - Sao Paulo - SP, BRAZIL
TEL: (011) 4615 5666
MARTINIQUE
Musique & Son
Z.I.Les Mangle
97232 Le Lamantin
Martinique F.W.I.
TEL: 596 596 426860
TEL: (02) 2561 3339
TEL: (010) 6426-5050
NORTH AMERICA
Roland Shanghai Electronics
Co.,Ltd.
THAILAND
Theera Music Co. , Ltd.
330 Verng NakornKasem, Soi
2, Bangkok 10100, THAILAND
TEL: (02) 2248821
CHILE
CANADA
(GUANGZHOU OFFICE)
2/F., No.30 Si You Nan Er Jie
Yi Xiang, Wu Yang Xin Cheng,
Guangzhou 510600, CHINA
TEL: (020) 8736-0428
Comercial Fancy II S.A.
Rut.: 96.919.420-1
Roland Canada Music Ltd.
(Head Office)
Gigamusic SARL
10 Rte De La Folie
97200 Fort De France
Martinique F.W.I.
TEL: 596 596 715222
Nataniel Cox #739, 4th Floor
Santiago - Centro, CHILE
TEL: (02) 688-9540
5480 Parkwood Way Richmond
B. C., V6V 2M4 CANADA
TEL: (604) 270 6626
VIETNAM
SAIGON MUSIC
DISTRIBUTOR
HONG KONG
U. S. A.
COLOMBIA
Parsons Music Ltd.
(TAN DINH MUSIC)
138 Tran Quang Khai Street
Dist. 1, Ho Chi Minh City
VIETNAM
Roland Corporation U.S.
5100 S. Eastern Avenue
Los Angeles, CA 90040-2938,
U. S. A.
Centro Musical Ltda.
Cra 43 B No 25 A 41 Bododega 9
Medellin, Colombia
TEL: (574)3812529
MEXICO
8th Floor, Railway Plaza, 39
Chatham Road South, T.S.T,
Kowloon, HONG KONG
TEL: 2333 1863
Casa Veerkamp, s.a. de c.v.
Av. Toluca No. 323, Col.
Olivar de los Padres 01780
Mexico D.F. MEXICO
TEL: (55) 5668-6699
TEL: (08) 848-4068
TEL: (323) 890 3700
CURACAO
INDIA
Zeelandia Music Center Inc.
Orionweg 30
Rivera Digitec (India) Pvt. Ltd.
409, Nirman Kendra
AUSTRALIA/
NEW ZEALAND
AFRICA
NICARAGUA
Curacao, Netherland Antilles
TEL:(305)5926866
Mahalaxmi Flats Compound
Off. Dr. Edwin Moses Road,
Mumbai-400011, INDIA
TEL: (022) 2493 9051
Bansbach Instrumentos
Musicales Nicaragua
Altamira D’Este Calle Principal
de la Farmacia 5ta.Avenida
1 Cuadra al Lago.#503
Managua, Nicaragua
TEL: (505)277-2557
EGYPT
Al Fanny Trading Office
9, EBN Hagar A1 Askalany
Street,
AUSTRALIA/
DOMINICAN
NEW ZEALAND
Roland Corporation
Australia Pty.,Ltd.
38 Campbell Avenue
Dee Why West. NSW 2099
AUSTRALIA
REPUBLIC
ARD E1 Golf, Heliopolis,
Cairo 11341, EGYPT
TEL: 20-2-417-1828
INDONESIA
PT Citra IntiRama
J1. Cideng Timur No. 15J-150
Jakarta Pusat
INDONESIA
TEL: (021) 6324170
Instrumentos Fernando
Giraldez
Calle Proyecto Central No.3
Ens.La Esperilla
Santo Domingo,
Dominican Republic
TEL:(809) 683 0305
PERU
REUNION
Audionet
Maison FO - YAM Marcel
25 Rue Jules Hermann,
Chaudron - BP79 97 491
Ste Clotilde Cedex,
For Australia
Distribuciones Musicales SAC
Juan Fanning 530
Miraflores
Lima - Peru
TEL: (511) 4461388
Tel: (02) 9982 8266
For New Zealand
Tel: (09) 3098 715
KOREA
Cosmos Corporation
1461-9, Seocho-Dong,
Seocho Ku, Seoul, KOREA
REUNION ISLAND
TEL: 7(02662) 218-429
DownloaTdELf:r(o02m) 348W6-8w855w.Somanuals.com. All Manuals Search And Download.
TRINIDAD
FINLAND
PORTUGAL
OMAN
MIDDLE EAST
AMR Ltd
Roland Scandinavia As, Filial Roland Iberia, S.L.
TALENTZ CENTRE L.L.C.
Malatan House No.1
Al Noor Street, Ruwi
SULTANATE OF OMAN
TEL: 2478 3443
Ground Floor
Finland
Elannontie 5
FIN-01510 Vantaa, FINLAND
TEL: (0)9 68 24 020
Portugal Office
BAHRAIN
Maritime Plaza
Barataria Trinidad W.I.
TEL: (868)638 6385
Cais das Pedras, 8/9-1 Dto
4050-465, Porto, PORTUGAL
TEL: 22 608 00 60
Moon Stores
No.16, Bab Al Bahrain Avenue,
P.O.Box 247, Manama 304,
State of BAHRAIN
TEL: 17 211 005
URUGUAY
GERMANY
ROMANIA
FBS LINES
Piata Libertatii 1,
535500 Gheorgheni,
ROMANIA
QATAR
Todo Musica S.A.
Roland Elektronische
Badie Studio & Stores
P.O. Box 62,
Francisco Acuna de Figueroa 1771 Musikinstrumente HmbH.
C.P.: 11.800
Montevideo, URUGUAY
TEL: (02) 924-2335
CYPRUS
Oststrasse 96, 22844
Norderstedt, GERMANY
TEL: (040) 52 60090
Doha, QATAR
TEL: 423554
Radex Sound Equipment Ltd.
17, Diagorou Street, Nicosia,
CYPRUS
TEL: (266) 364 609
SAUDI ARABIA
aDawliah Universal
Electronics APL
Corniche Road, Aldossary
Bldg., 1st Floor, Alkhobar,
SAUDI ARABIA
VENEZUELA
GREECE
RUSSIA
TEL: (022) 66-9426
Instrumentos Musicales
Allegro,C.A.
STOLLAS S.A.
MuTek
IRAN
Music Sound Light
155, New National Road
Patras 26442, GREECE
TEL: 2610 435400
Dorozhnaya ul.3,korp.6
117 545 Moscow, RUSSIA
TEL: (095) 981-4967
MOCO INC.
Av.las industrias edf.Guitar
import
#7 zona Industrial de Turumo
Caracas, Venezuela
TEL: (212) 244-1122
No.41 Nike St., Dr.Shariyati Ave.,
Roberoye Cerahe Mirdamad
Tehran, IRAN
SPAIN
P.O.Box 2154, Alkhobar 31952
SAUDI ARABIA
TEL: (03) 898 2081
HUNGARY
Roland Iberia, S.L.
Paseo García Faria, 33-35
TEL: (021) 285-4169
Roland East Europe Ltd.
ISRAEL
Warehouse Area ‘DEPO’ Pf.83 08005 Barcelona SPAIN
H-2046 Torokbalint,
HUNGARY
EUROPE
SYRIA
Halilit P. Greenspoon & Sons
Ltd.
TEL: 93 493 91 00
Technical Light & Sound
Center
AUSTRIA
SWEDEN
8 Retzif Ha’aliya Hashnya St.
Tel-Aviv-Yafo ISRAEL
TEL: (03) 6823666
TEL: (23) 511011
Roland Elektronische
Musikinstrumente HmbH.
Austrian Office
Roland Scandinavia A/S
SWEDISH SALES OFFICE
Danvik Center 28, 2 tr.
S-131 30 Nacka SWEDEN
TEL: (0)8 702 00 20
Rawda, Abdul Qader Jazairi St.
Bldg. No. 21, P.O.BOX 13520,
Damascus, SYRIA
TEL: (011) 223-5384
IRELAND
Roland Ireland
JORDAN
Eduard-Bodem-Gasse 8,
A-6020 Innsbruck, AUSTRIA
TEL: (0512) 26 44 260
G2 Calmount Park, Calmount
Avenue, Dublin 12
Republic of IRELAND
TEL: (01) 4294444
MUSIC HOUSE CO. LTD.
FREDDY FOR MUSIC
P. O. Box 922846
TURKEY
SWITZERLAND
Roland (Switzerland) AG
Landstrasse 5, Postfach,
CH-4452 Itingen,
SWITZERLAND
TEL: (061) 927-8383
ZUHAL DIS TICARET A.S.
Galip Dede Cad. No.37
Beyoglu - Istanbul / TURKEY
TEL: (0212) 249 85 10
BELGIUM/FRANCE/
HOLLAND/
Amman 11192 JORDAN
TEL: (06) 5692696
ITALY
Roland Italy S. p. A.
Viale delle Industrie 8,
20020 Arese, Milano, ITALY
TEL: (02) 937-78300
LUXEMBOURG
KUWAIT
Roland Central Europe N.V.
Houtstraat 3, B-2260, Oevel
(Westerlo) BELGIUM
TEL: (014) 575811
U.A.E.
EASA HUSAIN AL-YOUSIFI
& SONS CO.
Zak Electronics & Musical
Instruments Co. L.L.C.
Zabeel Road, Al Sherooq Bldg.,
No. 14, Grand Floor, Dubai,
U.A.E.
UKRAINE
TIC-TAC
Mira Str. 19/108
P.O. Box 180
295400 Munkachevo,
UKRAINE
TEL: (03131) 414-40
Abdullah Salem Street,
Safat, KUWAIT
TEL: 243-6399
NORWAY
Roland Scandinavia Avd.
Kontor Norge
CZECH REP.
K-AUDIO
Kardasovska 626.
CZ-198 00 Praha 9,
CZECH REP.
LEBANON
Lilleakerveien 2 Postboks 95
Lilleaker N-0216 Oslo
NORWAY
TEL: (04) 3360715
Chahine S.A.L.
Gerge Zeidan St., Chahine
Bldg., Achrafieh, P.O.Box: 16-
5857
Beirut, LEBANON
TEL: (01) 20-1441
TEL: 2273 0074
TEL: (2) 666 10529
UNITED KINGDOM
Roland (U.K.) Ltd.
Atlantic Close, Swansea
Enterprise Park, SWANSEA
POLAND
DENMARK
MX MUSIC SP.Z.O.O.
UL. Gibraltarska 4.
Roland Scandinavia A/S
Nordhavnsvej 7, Postbox 880,
DK-2100 Copenhagen
DENMARK
PL-03664 Warszawa POLAND SA7 9FJ,
TEL: (022) 679 44 19 UNITED KINGDOM
TEL: (01792) 702701
As of December 1, 2005
(EDIROL-1)
TEL: 3916 6200
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Memo
78
Download from Www.Somanuals.com. All Manuals Search And Download.
For EU Countries
For the USA
This product complies with the requirements of European Directive 89/336/EEC.
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a
residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in
a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Unauthorized changes or modification to this system can void the users authority to operate this equipment.
This equipment requires shielded interface cables in order to meet FCC class B Limit.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
For the USA
DECLARATION OF CONFORMITY
Compliance Information Statement
Model Name : UM-1EX
Type of Equipment : USB MIDI Interface
Responsible Party : Roland Corporation U.S.
Address : 5100 S. Eastern Avenue, Los Angeles, CA 90040-2938
Telephone : (323) 890 3700
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|