Dynex TV Mount DX TVM111 User Manual

ASSEMBLY GUIDE  
DX-TVM111  
TV Wall Mount  
Safety information and specifications . . . . . . . . . 2  
Tools needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Package contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . 4  
For either wood-stud or  
concrete wall installations  
Before using your new product, please read these instructions to prevent any damage.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Package contents  
DX-TVM111  
Package contents  
Make sure that you have all the hardware necessary to assemble your new TV wall mount:  
A TV Bracket (1)  
B Wall Plate (1)  
J Wall mount template (1)  
B
J
A
TV Hardware Bag  
Label  
Hardware  
Qty.  
Label  
Hardware  
Qty.  
M4 × 12 mm  
screw  
C
4
G
2
1/4" × 2 1/2" lag bolt  
M4 × 30 mm  
D
E
4
4
screw  
Concrete anchor  
H
I
2
1
M4 washer  
M4 spacers  
F
4
Locking bar  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
4
DX-TVM111  
Installation instructions  
Installation instructions  
STEP 1 - Determine wall-mount location  
Notes:  
• For more detailed information on determining where to drill your holes, visit our online height-finder at:  
• Your TV should be high enough so your eyes are level with the middle of the screen. Normally, 40 to 60 inches from the  
ground.  
The center of your TV will match the center of the wall plate (B). Before you drill holes in the wall:  
1 Measure the distance from the bottom of your TV to the middle (half of the height of the TV). This is  
measurement a.  
2 Measure the distance from the floor to where you want the bottom of the TV to be placed on the wall. Keep in  
mind that the bottom of the TV should be placed above any furniture (such as entertainment centers or TV  
stands). The TV should also be above items placed on top of the furniture (like a Blu-ray player or cable box).  
This measurement is b.  
3 Add a + b. The total measurement is the height where you want the center of the wall plate (B) to be on the  
wall.  
4 Use a pencil to mark this spot on the wall.  
a
b
You’ll need  
Pencil  
Measuring tape  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
5
Installation instructions  
DX-TVM111  
STEP 2 - Option 1: Installing on a wood stud* wall  
Note: Any wallboard or material covering the wall must not exceed 5/8" (16 mm).  
1 Locate the stud. Verify the center of the stud with an edge-to-edge stud finder.  
2 Align the wall plate template (J) at the height you determined in the previous step and make sure that it is  
level. Tape the wall plate template in position, then use a pencil to mark the lag bolt hole locations (2).  
Remove the wall plate template.  
3 Drill pilot holes to a depth of 3 in. (75 mm) using a 1/8" (3 mm) wood drill bit.  
4 Align the wall plate (B) with the pilot holes, insert the lag bolts (G) through the holes in the wall plate, then  
tighten the lag bolts only until they are firm against the arm assembly.  
CAUTION: Avoid potential injuries or property damage!  
DO NOT over-tighten the lag bolts (G).  
* Minimum wood stud size: common 2 x 4 in. (51 x 102 mm)  
nominal 11/2 x 31/2 in. (38 x 89 mm).  
3 in.  
(75 mm)  
You’ll need  
DX-TVM111  
Template  
Gabarit  
Plantilla  
Top  
Haut  
Parte superior  
Tools Needed  
Outils nécessaires  
Herramientas requeridas  
Note  
Remarque  
localiser d'abord les montants en bois,  
détecteur de montants.  
:
Pour une construction  
à
ossature de bois,  
l'aide d'un  
à
Nota: para la instalación en construcciones de armazón de  
madera, primero debe localizar las vigas de madera con un  
localizador de vigas.  
G (2)  
Pencil  
Tape  
1/8" wood  
drill bit  
Need more information about your mount? Scan  
<FR>Need more information about your mount?  
<SP>Need more information about your mount?  
7/16" socket  
wrench  
V1 13-0138  
Edge-to edge  
stud finder  
Drill  
Template (J)  
Level  
Wall plate (B)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
DX-TVM111  
Installation instructions  
STEP 2 - Option 2: Installing on a solid concrete* or concrete block wall  
CAUTION: To prevent property damage or personal injury, never drill into mortar between blocks. Mount wall plate  
directly onto the concrete surface.  
1 Align the wall plate template (J) at the height you determined in the previous step and make sure that it is  
level. Tape the wall plate template in position, then use a pencil to mark the lag bolt hole locations (2).  
Remove the wall plate template.  
2 Drill pilot holes to a depth of 3 in. (75 mm) using a 1/2 in. (12 mm) diameter masonry drill bit.  
3 Insert the concrete wall anchors (H) into the pilot holes and use a hammer to make sure the anchors are flush  
with the concrete surface.  
4 Align the wall plate (B) with the anchors, insert the lag bolts (G) through the holes in the wall plate, then  
tighten the lag bolts only until they are firm against the wall plate.  
CAUTION: Avoid potential injuries or property damage!  
DO NOT over-tighten the lag bolts (G).  
* Minimum solid concrete thickness: 8 in. (203 mm)  
* Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)  
3 in.  
(75 mm)  
You’ll need  
DX-TVM111  
Template  
Gabarit  
Plantilla  
Top  
Haut  
Parte superior  
Tools Needed  
Outils nécessaires  
Herramientas requeridas  
Note  
Remarque  
localiser d'abord les montants en bois,  
détecteur de montants.  
:
Pour une construction  
à
ossature de bois,  
l'aide d'un  
à
Nota: para la instalación en construcciones de armazón de  
madera, primero debe localizar las vigas de madera con un  
localizador de vigas.  
G (2)  
Level  
1/2" masonry  
drill bit  
Pencil  
Need more information about your mount? Scan  
<FR>Need more information about your mount?  
<SP>Need more information about your mount?  
V1 13-0138  
7/16" socket  
wrench  
Drill  
Template (J)  
H (2)  
Wall plate (B)  
Hammer  
Tape  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Installation instructions  
DX-TVM111  
STEP 3 - Determine whether your TV has a flat, irregular, or obstructed back  
1 Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages  
and scratches.  
2 If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV  
for instructions.  
3 Temporarily lay the TV bracket (A) on the back of your TV.  
4 Align the screw holes in the TV bracket with the mounting screw holes on your TV.  
5 Identify which type of back your TV may have:  
Flat back: The bracket lays flush against the back of your TV and do not block any jacks. You do not need spacers when  
assembling the wall mount.  
Obstructed back: The bracket blocks one or more of the jacks on the back of your TV. You will need spacers when  
assembling the wall mount.  
Irregularly-shaped back: There is a gap between the bracket and some part of the back of your TV. You will need  
spacers when assembling the wall mount.  
6 Remove the TV bracket (A).  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
DX-TVM111  
Installation instructions  
STEP 4 - Select screws, washers, and spacers  
1 Select the hardware for your TV (screws, washers, and spacers). A limited number of TVs come with mounting  
hardware included. (If there are screws that came with the TV, they are almost always in the holes on the back  
of the TV.)  
Select one of the following types of screws:  
M4 × 12 mm screws (C) for a flat back TV.  
M4 × 30 mm screws (D) for an irregular or obstructed TV back.  
For an irregular or obstructed TV back, use the following spacers:  
Universal spacers (F)  
CAUTION: To avoid potential personal injuries and  
property damage, make sure that there are adequate threads  
to secure the brackets to your TV. If you encounter resistance,  
stop immediately and contact customer service. Use the  
shortest screw and spacer combination to accommodate your  
TV. Using hardware that is too long may damage your TV.  
However, using a screw that is too short may cause your TV to  
fall from the mount.  
Screw fits  
correctly  
Screw is  
too long  
Screw is  
too short  
2 Remove the screws.  
3 For a flat back TV, go to “STEP 5 - Option 1: Attaching the mounting hardware to TVs with a flat back“ on  
page 9.  
-OR-  
For an irregular or obstructed back, go to “STEP 5 - Option 2: Attaching the mounting hardware to TVs with  
irregular or obstructed backs” on page 10.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Installation instructions  
DX-TVM111  
STEP 5 - Option 1: Attaching the mounting hardware to TVs with a flat back  
1 Align the TV bracket (A) with the screw holes on the back of the TV.  
2 Install washers (E ), and screws (C) into the top two holes in the back of the TV.  
NOTE: If the hole pattern on your TV is 75 mm x 75 mm, do not use the washers (E).  
3 Tighten the screws until they are snug against the TV bracket. Do not over tighten.  
You’ll need  
Washers  
Screws  
Phillips screwdriver  
C (4)  
E (4)  
TV bracket (A)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
10  
DX-TVM111  
Installation instructions  
STEP 5 - Option 2: Attaching the mounting hardware to TVs with irregular or obstructed  
backs  
1 Align the TV bracket (A) with the screw holes on the back of the TV.  
2 Place spacers (F) behind the TV bracket and the washers (E) over the holes in the TV bracket, then insert the  
screws (D) through the washers, TV bracket, and spacers.  
NOTE: If the hole pattern on your TV is 75 mm x 75 mm, do not use the washers (E).  
3 Tighten the screws until they are snug against the TV bracket. Do not over tighten.  
You’ll need  
Washers  
Spacers  
Screws  
Phillips screwdriver  
D (4)  
F (4)  
E (4)  
TV bracket (A)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
11  
Installation instructions  
DX-TVM111  
STEP 6 - Mounting the TV to the wall plate  
• Place the TV bracket (A) into the slotted flanges of the wall plate (B). The TV can be mounted either (1) vertically, or (2)  
with a 5° tilt.  
HEAVY! You will need  
assistance with this step.  
1 - Vertical mount  
Note: Attach the TV bracket to the flange that is closest to the wall plate.  
2 - Tilt mount  
Note: Attach the TV bracket to the flange that is farthest from the wall plate.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
DX-TVM111  
Installation instructions  
STEP 7 - Locking the TV to the wall plate  
• Slide the locking bar (I) through the TV bracket (A) and the wall plate (B) to secure the TV. A padlock (not included) may  
be used for extra security.  
Vertical mount  
Tilt mount  
You’ll need  
Locking bar (I)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Distributed by Best Buy Purchasing, LLC  
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.  
© 2013 BBY Solutions, Inc. All rights reserved.  
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and  
brand names are trademarks of their respective owners.  
6907-002009 <02>  
V1 ENGLISH 12-1055  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Code Alarm Remote Starter CA 5050 User Manual
Cooper Lighting Indoor Furnishings Wall Bracket User Manual
Cuisinart Blender ICE 40 User Manual
Cuisinart Toaster CMT 400PC User Manual
Curtis Portable CD Player RCD674 User Manual
CyberHome Entertainment DVD Player CH DVD 635S User Manual
Everpure Water System EV9328 02 User Manual
Fujitsu Air Conditioner AOU12RL2 User Manual
Gardena Weather Radio ART1189 User Manual
GE Oven 164D2966P087 User Manual