LCD Data Video Projector
User’s Manual
MODEL 8791HW
Information in this Guide may change due to product improvements. To obtain the latest
and look at the specific model SUPPORT or DOWNLOADS section.
DUKANE CORP AV SERVICE DEPT
2900 Dukane Drive
St Charles, IL 60174
800-676-2487 / 630-762-4032
Fax 630-584-5156
403-8791HW-GENERAL-00
Download from Www.Somanuals.com. All Manuals Search And Download.
P8r7oje9c1toHr W
User's Manual (detailed)
Operating Guide
Thank you for purchasing this projector.
WARNING ►Before using this product, please read all manuals for this
product. Be sure to read “Safety Guide” first. After reading them, store them in a
safe place for future reference.
About this manual
Various symbols are used in this manual. The meanings of these symbols are
described below.
WARNING This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.
CAUTION This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.
NOTICE
This entry notices of fear of causing trouble.
Please refer to the pages written following this symbol.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
Trademark acknowledgment
• Mac® is a registered trademark of Apple Inc.
• Microsoft®, Internet Explorer®, Windows® and Windows Vista® are registered
trademarks of Microsoft Corporation in the U.S. and/or other countries.
• VESA and DDC are trademarks of the Video Electronics Standard Association.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
• Blu-ray DiscTM and Blu-rayTM are trademarks of Blu-ray Disc Association.
All other trademarks are the properties of their respective owners.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Contents
Introduction . . . . . . . . . . . . . . . 3 PICTURE menu . . . . . . . . . . . . 27
Br ig h t n e s s , co n t r A s t , gA m m A ,
co l o r t e m p , co l o r , tin t , sh A r p n e s s ,
my m e m o r y
Features . . . . . . . . . . . . . . . . . . . . . . 3
Checking the contents of package. . . 3
Part names . . . . . . . . . . . . . . . . 4
Projector . . . . . . . . . . . . . . . . . . . . . . 4
Control panel. . . . . . . . . . . . . . . . . . . 5
Rear panel . . . . . . . . . . . . . . . . . . . . 5
Remote control . . . . . . . . . . . . . . . . . 6
Setting up . . . . . . . . . . . . . . . . . 7
Arrangement . . . . . . . . . . . . . . . . . . . 7
Connecting your devices. . . . . . . . . . 9
Connecting power supply . . . . . . . . 11
Using the security bar and slot . . . . 11
Remote control . . . . . . . . . . . . 12
Installing the batteries. . . . . . . . . . . 12
About the remote control signal . . . 12
Power on/off . . . . . . . . . . . . . . 13
Turning on the power . . . . . . . . . . . 13
Turning off the power . . . . . . . . . . . 13
IMAGE menu . . . . . . . . . . . . . . 30
As p e c t , ov e r s c A n , v p o s it io n , h p o s it io n ,
h p h A s e , h s iz e , Au t o A d j u s t e x e c u t e
INPUT menu . . . . . . . . . . . . . . 33
pr o g r e s s iv e , vid e o n r , co l o r s p A c e ,
vid e o F o r m A t , hd m i F o r m A t , hd m i r A n g e ,
co m p u t e r in, Fr A m e l o c k , re s o l u t io n
SETUP menu . . . . . . . . . . . . . . 37
Au t o k e y s t o n e , ke y s t o n e , Au t o e c o m o d e
ec o m o d e , mir r o r , st A n d B y m o d e ,
mo n it o r o u t
AUDIO menu . . . . . . . . . . . . . . 39
vo l u m e , sp e A k e r , Au d io s o u r c e ,
hd m i A u d io
SCREEN menu. . . . . . . . . . . . . 40
Operating . . . . . . . . . . . . . . . . 15 lA n g u A g e , me n u p o s it io n , Bl A n k ,
st A r t u p ,
,
M
yScreen
, M
yScreen Lock
Adjusting the volume. . . . . . . . . . . . 15
Temporarily muting the sound. . . . . 15
Selecting an input signal. . . . . . . . . 15
Searching an input signal . . . . . . . . 17
Selecting an aspect ratio. . . . . . . . . 17
Adjusting the projector's elevator . . 18
Adjusting the zoom and focus. . . . . 18
Using the automatic adjustment feature. . . 19
Adjusting the position . . . . . . . . . . . 19
Correcting the keystone distortions. . 20
Using the magnify feature. . . . . . . . 21
Temporarily freezing the screen . . . 22
Temporarily blanking the screen . . 22
Using the menu function . . . . . . . . 23
me s s A g e , so u r c e n A m e , te m p l A t e , c.c.
OPTION menu . . . . . . . . . . . . . 46
Au t o s e A r c h , Au t o k e y s t o n e ,
dir e c t p o w e r o n , Au t o p o w e r o F F ,
lA m p t im e , Fil t e r t im e , my B u t t o n ,
my s o u r c e , se r v ic e
SECURITY menu . . . . . . . . . . . 51
se c u r it y p A s s w o r d c h A n g e ,
p A s s w o r d , pin l o c k ,
M
yScreen
tr A n s it io n d e t e c t o r , my t e x t p A s s w o r d ,
my t e x t d is p l A y , my t e x t w r it in g
Maintenance . . . . . . . . . . . . . . 57
Replacing the lamp . . . . . . . . . . . . . 57
Cleaning and replacing the air filter . . 59
Other care. . . . . . . . . . . . . . . . . . . . 61
Troubleshooting . . . . . . . . . . . 62
Related messages . . . . . . . . . . . . . 62
Regarding the indicator lamps . . . . 63
Resetting all settings. . . . . . . . . . . . 64
Phenomena that may be easy
EASY MENU. . . . . . . . . . . . . . . 25
As p e c t , Au t o k e y s t o n e , ke y s t o n e ,
pic t u r e m o d e , ec o m o d e , mir r o r , re s e t ,
Fil t e r t im e , lA n g u A g e , Ad v A n c e d m e n u ,
ex it
to be mistaken for machine defects. . 65
Specifications . . . . . . . . . . . . . 69
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Introduction
Features
The projector provides you with the broad use by the following features.
ü This projector has a variety of I/O ports that supposedly cover for any
business scene. The HDMI port can support various image equipment
which have digital interface to get clearer pictures on a screen.
ü This projector realizes the large projection image, even if in a small space.
ü The new double layer filter system is expected to function longer and offers
you less maintenance frequency.
ü This compact, lightweight projector uses a front exhaust system that keeps
the user comfortable by directing hot air away from the user.
Checking the contents of package
Please see the Contents of package section in the User’s Manual (concise)
which is a book. Require of your dealer immediately if any items are missing.
NOTE • Keep the original packing materials, for future reshipment. Be sure
to use the original packing materials when moving the projector. Use special
caution for the lens.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Part names
Part names
Projector
(1)
HOT!
(2) (3)
(4)
(11)
(9)
(1) Lamp cover (57)
The lamp unit is inside.
(2) Focus ring (18)
(3) Zoom ring (18)
(15)
(10)
(5)
(4) Control panel (5)
(5) Elevator buttons (x 2) (18)
(6) Elevator feet (x 2) (18)
(7) Remote sensor (12)
(8) Lens (61)
(6)
(7)
(8)
(6)
(12)
HOT!
(9) Intake vents
(10) Filter cover (59)
The air filter and intake vent are
(5)
inside.
(11) Speaker (39)
(12) Exhaust vent
(13) AC IN (AC inlet) (11)
(14) Rear panel (5)
(15) Security bar (11)
(16) Security slot (11)
(9)
(16)
(13)
(14)
WARNING ►HOT! : Do not touch around the lamp cover and the exhaust
vents during use or just after use, since it is too hot.
►Do not look into the lens or vents while the lamp is on, since the strong light is
not good for your eyes.
►Do not handle the elevator buttons without holding the projector, since the
projector may drop down.
►Do not use the security bar and slot to prevent the projector from falling down,
since it is not designed for it.
CAUTION ►Maintain normal ventilation to prevent the projector from
heating up. Do not cover, block or plug up the vents. Do not place anything that
can stick or be sucked to the vents, around the intake vents. Clean the air filter
periodically.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Part names
Control panel
%/$1.
0<ꢀ%87721
(1) STANDBY/ON button (13)
(2) INPUT button (15, 23)
(3) MENU button (23)
It consists of four cursor buttons.
(4) BLANK button (22)
(4)
(5) POWER indicator (11, 13, 63)
(6) TEMP indicator (63)
(7) LAMP indicator (63)
(6)(7)
(5)
(1)
(2)
(3)
Rear panel (9)
(1) VIDEO port
(6) COMPUTER IN port
(7) HDMI port
(8) CONTROL port
(9) MONITOR OUT port
(2) S-VIDEO port
(3) AUDIO IN1 port
(4) AUDIO IN2 port
(5) AUDIO OUT port
(2)
(3)
(6)
(7)
(1)
(5)
(9)
(4)
(8)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Part names
Remote control
(1) VIDEO button (16)
(2)
(1)
(6)
(5)
(16)
(8)
(9)
(19)
(17)
(20)
(22)
(10)
(4)
(3)
(2) COMPUTER button (16)
(3) SEARCH button (17)
(4) STANDBY/ON button (13)
(5) ASPECT button (17)
(6) AUTO button (19)
(7) BLANK button (22)
(8) MAGNIFY - ON button (21)
(9) MAGNIFY - OFF button (21)
(10) MY SOURCE/DOC.CAMERA button (16, 48)
(11) VOLUME - button (15)
(12) PAGE UP button *
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
(7)
MAGNIFY
FREEZE
PAGE
UP
VOLUME
(12)
(14)
(11)
(13)
(15)
(18)
(21)
(23)
(25)
㧗
ON
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
POSITION
ENTER
ESC
RESET
(24)
(13) PAGE DOWN button *
(14) VOLUME + button (15)
(15) MUTE button (15)
(16) FREEZE button (22)
(17) MY BUTTON - 1 button (48)
(18) MY BUTTON - 2 button (48)
(19) KEYSTONE button (20)
(20) POSITION button (19, 24)
(21) MENU button (23)
(22) ▲/▼/◄/► cursor buttons (23)
(23) ENTER button (23)
(24) ESC button (23)
(26)
(25) RESET button (23)
(26) Battery cover (12)
Back of
the remote control
NOTE • Any button marked with “*” is not supported on this projector (62).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Setting up
Install the projector according to the environment and manner the projector will be
used in.
Arrangement
Refer to the illustrations and tables below to determine screen size and projection
distance.
The values shown in the table are calculated for a full size screen: 1280 x 800
a Screen size (diagonal)
b
Projection distance (±10%, from the projector's end)
c1 , c2 Screen height (±10%)
On a horizontal surface
Suspended from the ceiling
• Keep a space of 30 cm or more between the
sides of the projector and other objects such
as walls.
• For the case of installation in a special
state such as ceiling mount, the specified
mounting accessories (69) and service may
be required. Before installing the projector,
consult your dealer about your installation.
16 : 10 screen
4 : 3 screen
a
b
b
c1
Screen
height
c2
Screen
height
c1
Screen
height
c2
Screen
height
Screen size
(diagonal)
Projection distance
Projection distance
min. max.
min.
max.
type
(inch)
m
m
inch
m
inch cm inch cm inch
m
inch
m
inch cm inch cm inch
30 0.8 0.9 36 1.1 44
40 1.0 1.2 49 1.5 59
50 1.3 1.6 61 1.9 74
60 1.5 1.9 74 2.3 89
38
50
63
75
15
20
25
30
34
3
4
5
6
7
8
9
1
2
2
2
3
3
3
4
5
6
8
9
1.0 41 1.3 50
1.4 56 1.7 67
1.8 70 2.1 84
42
57
71
18
22
28
33
39
3
4
1
2
5
2
2.1 84 2.6 101 85
2.5 99 3.0 119 99
7
3
70 1.8 2.2 87 2.7 105 88
8
3
80 2.0 2.5 100 3.0 120 100 39
2.9 113 3.5 136 113 45
3.2 127 3.9 153 127 50
3.6 142 4.3 170 142 56
4.3 170 5.2 205 170 67
5.4 214 6.5 257 212 84
9
3
90 2.3 2.9 112 3.4 135 113 44
10
11
13
18
4
100 2.5 3.2 125 3.8 150 125 49 10
120 3.0 3.8 150 4.6 181 150 59 12
4
5
150 3.8 4.8 188 5.8 227 188 74
200 5.1 6.4 252 7.7 303 250 98
14
19
6
7.2 285 8.7 343 283 111 22
9.1 357 10.9 429 354 139 27
9
250 6.4 8.0 315 9.6 379 313 123 24
11
13
300 7.6 9.6 379 11.6 455 375 148 29 11 10.9 429 13.1 515 425 167 33
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Arrangement (continued)
WARNING ►Place the projector in a stable horizontal position. If the
projector falls or is knocked over, it could cause injury and/or damage to the
projector. Using a damaged projector could then result in fire and/or electric
shock.
• Do not place the projector on an unstable, slanted or vibrational surface such
as a wobbly or inclined stand.
• Do not place the projector on its side, front or rear position.
• Consult with your dealer before a special installation such as suspending from
a ceiling or somewhere else.
►Place the projector in a cool place, and ensure that there is sufficient
ventilation. The high temperature of the projector could cause fire, burns and/or
malfunction of the projector.
• Do not place or attach anything that would block the lens or vent holes.
• Keep a space of 30 cm or more between the sides of the projector and other
objects such as walls.
• Do not place the projector on metallic thing or anything weak in heat.
• Do not place the projector on carpet, cushions or bedding.
• Do not place the projector in direct sunlight or near hot objects such as heaters.
• Do not place anything near the projector lens or vents, or on top of the
projector.
•
Do not place anything that may be sucked into or stick to the vents on the
bottom of the projector. This projector has some intake vents also on the bottom.
►Do not place the projector anyplace where it may get wet. Getting the projector
wet or inserting liquid into the projector could cause fire, electric shock and/or
malfunction of the projector.
• Do not place the projector in a bathroom or the outdoors.
• Do not place anything containing liquid near the projector.
►Do not place the projector where any oils, such as cooking or machine oil, are
used.
►Use only the mounting accessories the manufacturer specified, and leave
installing and removing the projector with the mounting accessories to the
service personnel.
• Read and keep the user’s manual of the mounting accessories used.
CAUTION ►Avoid placing the projector in smoky, humid or dusty place.
Placing the projector in such places could cause fire, electric shock and/or
malfunction of the projector.
• Do not place the projector near humidifiers, smoking spaces or a kitchen. Also
do not use an ultrasonic humidifier near the projector. Otherwise chlorine and
minerals contained in tap water are atomized and could be deposited in the
projector causing image degradation or other problems.
►Position the projector to prevent light from directly hitting the projector's remote
sensor.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Connecting your devices
Be sure to read the manuals for devices before connecting them to the projector.
Make sure that all the devices are suitable to be connected with this product, and
prepare the cables required to connect. Please refer to the following illustrations
to connect them. To input component video signal to COMPUTER IN port, please
see the description of the COMPUTER IN item of the INPUT menu (35).
Monitor
PC
RGB IN
AUDIO OUT
RGB OUT
AUDIO OUT
RS-232C
Speakers
Y
CB/PB CR/PR
L
R
L
R
L
R
VIDEO OUT
HDMI
S-VIDEO OUT
AUDIO OUT
AUDIO OUT
AUDIO OUT
COMPONENT VIDEO OUT
(with an
amplifier)
L
R
AUDIO IN
VCR/DVD/Blu-ray Disc player
WARNING ►Do not disassemble or modify the projector and accessories.
►Be careful not to damage the cables, and do not use damaged cables.
CAUTION ►Turn off all devices and unplug their power cords prior to
connecting them to projector. Connecting a live device to the projector may
generate extremely loud noises or other abnormalities that may result in
malfunction or damage to the device and the projector.
►Use appropriate accessory or designated cables. Ask your dealer about non-
accessory cables which may be required a specific length or a ferrite core by
the regulations. For cables with a core only at one end, connect the end with
the core to the projector.
►Make sure that devices are connected to the correct ports. An incorrect
connection may result in malfunction or damage to the device and the projector.
NOTICE
►Use the cables with straight plugs, not L-shaped ones, as the
input ports of the projector are recessed.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Connecting your devices (continued)
NOTE
• Be sure to read the manuals for devices before connecting them to
the projector, and make sure that all the devices are suitable to be connected
with this product. Before connecting to a PC, check the signal level, the signal
timing, and the resolution.
- Some signal may need an adapter to input this projector.
- Some PCs have multiple screen display modes that may include some signals
which are not supported by this projector.
- Although the projector can display signals with resolution up to UXGA
(1600X1200), the signal will be converted to the projector’s panel resolution
before being displayed. The best display performance will be achieved if the
resolutions of the input signal and the projector panel are identical.
• While connecting, make sure that the shape of the cable's connector fits the
port to connect with. And be sure to tighten the screws on connectors with
screws.
• When connecting a laptop PC to the projector, be sure to activate the PC’s
external RGB output. (Set the laptop PC to CRT display or to simultaneous
LCD and CRT display.) For details on how this is done, please refer to the
instruction manual of the corresponding laptop PC.
• When the picture resolution is changed on a PC depending on an input,
automatic adjustment function may take some time and may not be completed.
In this case, you may not be able to see a check box to select “Yes/No” for the
new resolution on Windows. Then the resolution will go back to the original.
It might be recommended to use other CRT or LCD monitors to change the
resolution.
• In some cases, this projector may not display a proper picture or display
any picture on screen. For example, automatic adjustment may not function
correctly with some input signals. An input signal of composite sync or sync on
G may confuse this projector, so the projector may not display a proper picture.
About Plug-and-Play capability
Plug-and-Play is a system composed of a PC, its operating system and
peripheral equipment (i.e. display devices). This projector is VESA DDC 2B
compatible. Plug-and-Play can be used by connecting this projector to a PC
that is VESA DDC (display data channel) compatible.
• Take advantage of this feature by connecting a computer cable to the
COMPUTER IN port (DDC 2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.
• Please use the standard drivers in your PC as this projector is a Plug-and-
Play monitor.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up
Connecting power supply
Put the connector of the power cord into the
AC IN (AC inlet) of the projector.
1.
Firmly plug the power cord’s plug into the
outlet. In a couple of seconds after the
power supply connection, the POWER
2.
indicator will light up in steady orange.
Please remember that when the DIRECT POWER
ON function activated (46), the connection of
the power supply make the projector turn on.
AC IN
Power cord
WARNING ►Please use extra caution when connecting the power cord, as
incorrect or faulty connections may result in fire and/or electrical shock.
• Only use the power cord that came with the projector. If it is damaged, consult
your dealer to get a new one.
• Only plug the power cord into an outlet whose voltage is matched to the power
cord. The power outlet should be close to the projector and easily accessible.
Remove the power cord for complete separation.
• Never modify the power cord.
Security slot
Using the security bar and slot
A commercially available anti-theft chain or wire can
be attached to the security bar on the projector.
Refer to the figure to choose an anti-theft chain or wire.
Also this product has the security slot for the
Kensington lock.
For details, see the manual of the security tool.
Security bar
12 mm
Anti-theft chain or wire
18 mm
Installation surface
18 mm
10 mm
WARNING ►Do not use the security bar and slot to prevent the projector
from falling down, since it is not designed for it.
CAUTION ►Do not place anti-theft chain or wire near the exhaust vents. It
may become too hot.
NOTE • The security bar and slot is not comprehensive theft prevention
measures. It is intended to be used as supplemental theft prevention measure.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
Remote control
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote control
starts to malfunction, try to replace the batteries. If you will not use the remote control for
long period, remove the batteries from the remote control and store them in a safe place.
Holding the hook part of the battery
cover, remove it.
1
2
3
1.
2.
Align and insert the two AA batteries
(HITACHI MAXELL, Part No.LR6 or R6P)
according to their plus and minus terminals
as indicated in the remote control.
3. Replace the battery cover in the direction of the arrow and snap it back into place.
WARNING ►Always handle the batteries with care and use them only as
directed. Improper use may result in battery explosion, cracking or leakage,
which could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of different
types at the same time. Do not mix a new battery with used one.
•
Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
•
Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.
• If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.
• Obey the local laws on disposing the battery.
About the remote control signal
The remote control works with the projector’s remote
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range
when the sensor is active:
Approx.
3 m
30º
30º
60 degrees (30 degrees to the left and right of the sensor)
within 3 meters about.
NOTE • The remote control signal reflected in the screen or the like may be available.
If it is difficult to send the signal to the sensor directly, attempt to make the signal reflect.
• The remote control uses infrared light to send signals to the projector (Class 1
LED), so be sure to use the remote control in an area free from obstacles that
could block the remote control’s signal to the projector.
•
The remote control may not work correctly if strong light (such as direct sun
light) or light from an extremely close range (such as from an inverter fluorescent
lamp) shines on the remote sensor of the projector. Adjust the position of
projector avoiding those lights.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Power on/off
Power on/off
STANDBY/ON button
POWER indicator
Turning on the power
Make sure that the power cord is firmly and
correctly connected to the projector and the
outlet.
1.
Make sure that the POWER indicator is
steady orange (63). Then remove the lens
cover.
2.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
M
A
G
N
I
F
Y
F
R
E
E
Z
E
PAGE
UP
VOLUME
ON
＋
DOWN
OFF
ー
KEYSTONE
MY BUTTON
1
MUTE
2
POSITION
MENU
Press STANDBY/ON button on the
projector or the remote control.
The projection lamp will light up and POWER
ENTER
ESC
RESET
3.
indicator will begin blinking in green. When the power
is completely on, the indicator will stop blinking and light in steady green
(63).
To display the picture, select an input signal according to the section “Selecting an
input signal” (15).
Turning off the power
Press the STANDBY/ON button on the projector or the remote control. The
message “Power off?” will appear on the screen for about 5 seconds.
Press the STANDBY/ON button again while the message appears.
The projector lamp will go off, and the POWER indicator will begin blinking in
orange. Then POWER indicator will stop blinking and light in steady orange
when the lamp cooling is complete (63).
1.
2.
3. Attach the lens cover, after the POWER indicator turns in steady orange.
Do not turn the projector on for about 10 minutes or more after turning it off. Also,
do not turn the projector off shortly after turning it on. Such operations might cause
the lamp to malfunction or shorten the lifetime of some parts including the lamp.
WARNING ►A strong light is emitted when the projector’s power is on. Do
not look into the lens of the projector or look inside of the projector through any
of the projector’s openings.
►Do not touch around the lamp cover and the exhaust vents during use or just
after use, since it is too hot.
NOTE • Turn the power on/off in right order. Please power on the projector
prior to the connected devices.
•
This projector has the function that can make the projector automatically turn on/
off. Please refer to the DIRECT POWER ON (46) and AUTO POWER OFF (47)
items of the OPTION menu.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Power on/off
Precaution for lens cover attachment and removal
When you attach or remove the lens cover, move it vertically up and down while keeping
the knob to the right as illustrated in the figure.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Operating
VOLUME +/- button
Adjusting the volume
Use the VOLUME +/VOLUME - buttons to adjust the volume.
A dialog will appear on the screen to aid you in adjusting the
volume. If you do not do anything, the dialog will automatically
disappear after a few seconds.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
1.
ASPECT
AUTO SEARCH BLANK
MAGNIFY
FREEZE
PAGE
UP
VOLUME
㧗
ON
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
MENU
● When is selected for current picture input port, the volume
adjustment is disabled. Please see AUDIO SOURCE item of
AUDIO menu (39).
1
2
POSITION
● Even if the projector is in the standby state, the volume can be adjusted when
both of following conditions are satisfied.
- NORMAL is selected for the STANDBY MODE in the SETUP menu (38).
- An item other than is selected for the AUDIO OUT STANDBY of the
AUDIO SOURCE in the AUDIO menu (39).
Temporarily muting the sound
MUTE button
Press MUTE button on the remote control.
1.
MY SOURCE/
A dialog will appear on the screen indicating that you have
VIDEO COMPUTER DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
muted the sound.
FREEZE
PAGE
UP
VOLUME
MAGNIFY
To restore the sound, press the MUTE, VOLUME + or
VOLUME - button. Even if you do not do anything, the dialog
will automatically disappear after a few seconds.
㧗
ON
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
● When is selected for current picture input port, the sound
is always muted. Please see AUDIO SOURCE item of
AUDIO menu (39).
POSITION
● C.C. (Closed Caption) is automatically activated when sound is muted and an
input signal containing C.C. is received. This function is available only when
the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPUTER
IN, and when AUTO is selected for DISPLAY in the C.C. menu under the
SCREEN menu (45).
Selecting an input signal
Press INPUT button on the projector.
INPUT button
1.
Each time you press the button, the projector switches its
input port from the current port as below.
COMPUTER IN HDMI
VIDEO
S-VIDEO
● While ON is selected for AUTO SEARCH item in OPTION
menu (46), the projector will keep checking the ports in
above order repeatedly till an input signal is detected.
(continued on next page)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Selecting an input signal (continued)
COMPUTER button
Press COMPUTER button on the remote control to
select the COMPUTER IN port.
1.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
FREEZE
PAGE
UP
VOLUME
MAGNIFY
㧗
ON
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
POSITION
Press VIDEO button on the remote control.
Each time you press the button, the projector switches its
input port from the current port as below.
VIDEO button
1.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
HDMI
S-VIDEO
VIDEO
FREEZE
PAGE
UP
VOLUME
MAGNIFY
㧗
ON
DOWN
OFF
●
While ON is selected for AUTO SEARCH item in OPTION
menu, the projector will keep checking every port sequentially
till an input signal is detected (46). If VIDEO button is
pressed when COMPUTER IN port is selected, the projector
will check HDMI port first.
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
POSITION
Press the MY SOURCE / DOC. CAMERA button on
the remote control. The input signal will be changed
into the signal you set as MY SOURCE (48).
MY SOURCE /
1.
DOC. CAMERA button
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
● This function also can use for document camera. Select the
input port that connected the document camera.
ASPECT
AUTO SEARCH BLANK
FREEZE
PAGE
UP
VOLUME
MAGNIFY
㧗
ON
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
POSITION
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Searching an input signal
SEARCH button
Press SEARCH button on the remote control.
The projector will start to check its input ports as below in
order to find any input signals.
MY SOURCE/
1.
VIDEO COMPUTER DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
MAGNIFY
FREEZE
PAGE
UP
VOLUME
㧗
ON
When an input is found, the projector will stop searching
and display the image. If no signal is found, the projector will
return to the state selected before the operation.
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
POSITION
COMPUTER IN HDMI
VIDEO
S-VIDEO
● While ON is selected for AUTO SEARCH item in OPTION menu (46), the
projector will keep checking the ports in above order repeatedly till an input
signal is detected.
Selecting an aspect ratio
ASPECT button
Press ASPECT button on the remote control.
Each time you press the button, the projector switches the
mode for aspect ratio in turn.
1.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
FREEZE
PAGE
UP
VOLUME
MAGNIFY
For a computer signal
㧗
ON
DOWN
OFF
NORMAL 4:3 16:9 16:10 NATIVE
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
For an HDMI signal
POSITION
NORMAL 4:3 16:9 16:10 14:9 NATIVE
For a video signal, s-video signal or component video
signal
4:3 16:9 16:10 14:9 NATIVE
For no signal
16:10 (fixed)
● ASPECT button does not work when no proper signal is inputted.
● NORMAL mode keeps the original aspect ratio setting.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Adjusting the projector's elevator
When the place to put the projector is slightly uneven to the left or right, use the
elevator feet to place the projector horizontally.
Using the feet can also tilt the projector in order to project at
a suitable angle to the screen, elevating the front side of the
projector within 12 degrees.
12°
This projector has 2 elevator feet and 2 elevator knobs. An elevator foot is
adjustable while pulling up the elevator knob on the same side as it.
1. Holding the projector, pull the elevator knobs up to loose the elevator feet.
2. Position the front side of the projector to the desired height.
3. Release the elevator knobs in order to lock the elevator feet.
After making sure that the elevator feet are locked, put the projector down
gently.
4.
If necessary, the elevator feet can be manually twisted to make more precise
adjustments. Hold the projector when twisting the feet.
5.
1
5
To loose an elevator foot,
pull up the elevator knob
on the same side as it.
To finely adjust, twist the foot.
CAUTION ►Do not handle the elevator buttons without holding the
projector, since the projector may drop down.
►Do not tilt the projector other than elevating its front within 12 degrees using
the adjuster feet. A tilt of the projector exceeding the restriction could cause
malfunction or shortening the lifetime of consumables, or the projector itself.
Adjusting the zoom and focus
Zoom ring
Focus ring
1. Use the zoom ring to adjust the screen size.
2. Use the focus ring to focus the picture.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Using the automatic adjustment feature
AUTO button
Press AUTO button on the remote control.
1.
Pressing this button performs the following.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
For a computer signal
ASPECT
AUTO SEARCH BLANK
The vertical position, the horizontal position and the horizontal
phase will be automatically adjusted.
FREEZE
PAGE
UP
VOLUME
MAGNIFY
㧗
ON
DOWN
OFF
Make sure that the application window is set to its maximum size
prior to attempting to use this feature. A dark picture may still be
incorrectly adjusted. Use a bright picture when adjusting.
KEYSTONE
MY BUTTON
MUTE
MENU
1
2
POSITION
For a video signal and s-video signal
The video format best suited for the respective input signal will be selected
automatically. This function is available only when the AUTO is selected for
the VIDEO FORMAT item in the INPUT menu (34). The vertical position and
horizontal position will be automatically set to the default.
For a component video signal
The vertical position and horizontal position will be automatically set to the
default. The horizontal phase will be automatically adjusted.
● The automatic adjustment operation requires approx. 10 seconds. Also please
note that it may not function correctly with some input.
● When this function is performed for a video signal, a certain extra such as a line
may appear outside a picture.
● When this function is performed for a computer signal, a black frame may be
displayed on the edge of the screen, depending on the PC model.
●
The items adjusted by this function may vary when the FINE or DISABLE is selected
for the AUTO ADJUST item of the SERVICE item in the OPTION menu (49).
Adjusting the position
KEYSTONE
POSITION
MY BUTTON
1
MUTE
MENU
Press POSITION button on the remote control when no menu is
2
1.
indicated.
The “POSITION” indication will appear on the screen.
ENTER
Use the ▲/▼/◄/► cursor buttons to adjust the picture position.
When you want to reset the operation, press RESET button on
the remote control during the operation.
ESC
RESET
2.
To complete this operation, press POSITION button again. Even if
you do not do anything, the dialog will automatically disappear
POSITION button
after a few seconds.
●
When this function is performed on a video signal or s-video signal or component
video signal, some image such as an extra-line may appear at outside of the
picture.
● When this function is performed on a video signal or an s-video signal, the range
of this adjustment depends on OVER SCAN in IMAGE menu (30) setting. It is
not possible to adjust when OVER SCAN is set to 10.
● If POSITION button is pressed when a menu is indicated on screen, the displayed
picture does not move its position but the menu does.
● This function is unavailable for a signal from the HDMI port.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
KEYSTONE button
Correcting the keystone distortions
Press KEYSTONE button on the remote
control. A dialog will appear on the screen to
aid you in correcting the distortion.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
1.
ASPECT
AUTO SEARCH BLANK
MAGNIFY
FREEZE
PAGE
UP
VOLUME
㧗
ON
Use the ▲/▼ cursor buttons to select AUTO or MANUAL
operation, and press the ► button to perform the following.
(1) AUTO executes automatic vertical keystone correction.
(2) MANUAL displays a dialog for keystone correction.
Use the ◄/► buttons for adjustment.
DOWN
OFF
2.
KEYSTONE
MY BUTTON
MUTE
1
2
To close the dialog and complete this operation, press
KEYSTONE button again. Even if you do not do anything, the
dialog will automatically disappear after a few seconds.
● The adjustable range of this function will vary among inputs. For some input, this
function may not work well.
● When V:INVERT or H&V:INVERT is selected to the MIRROR item in the SETUP
menu, if the projector screen is inclined or angled downward, automatic vertical
keystone correction may not work correctly.
● When the zoom adjustment is set to the TELE (telephoto focus), this function may
be excessive. This function should be used when the zoom adjustment is set to
the full WIDE (wide-angle focus) whenever possible.
● When the projector is placed on the level (about ±4°), the automatic keystone
distortion correction may not work.
● When the projector is inclined to near ±30 degree or over, this function may not
work well.
● This function will be unavailable when Transition Detector is on (54).
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
MAGNIFY
ON/OFF button
Using the magnify feature
Press the MAGNIFY ON button on the remote control. The
picture will be magnified, and the MAGNIFY dialog will appear
on the screen. When the MAGNIFY ON button is pressed for
the first time after the projector is turned on, the picture will be
zoomed by 1.5 times. On the dialog, triangle marks to show
each direction will be displayed.
1.
MY SOURCE/
COMPUTER
VIDEO
DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
FREEZE
PAGE
UP
VOLUME
MAGNIFY
㧗
ON
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
1
2
While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor buttons
to shift the magnifying area.
2.
3.
4.
A magnifying glass icon will be displayed on the dialog when the MAGNIFY ON
button is pressed while the dialog with the triangles is displayed.
While the magnifying glass icon is displayed on the dialog, use the ▲/▼ cursor
buttons to adjust the magnification ratio. The magnification ratio will be adjusted
with fine steps. And changes in the ratio in single steps are subtle so they may be
hard to recognize.
5. Press the MAGNIFY OFF button on the remote control to exit magnification.
● The MAGNIFY dialog will automatically disappear in several seconds with no
operation. The dialog will appear again if the MAGNIFY ON button is pressed
when the dialog has automatically disappeared.
● While the MAGNIFY dialog is displayed, press the MAGNIFY ON button to switch
the dialog between magnifying area shifting (with the triangles) and magnification
ratio adjustment (with the magnifying glass icon).
● The magnification is automatically disabled when the displaying signal or its
display condition is changed.
● While the magnification is active, the keystone distortion condition may vary. It will
be restored when the magnification is disabled.
● Some horizontal stripes might be visible on the image while magnification is
active.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Temporarily freezing the screen
FREEZE button
Press the FREEZE button on the remote control.
The “FREEZE” indication will appear on the screen (however,
the indication will not appear when the OFF is selected for
the MESSAGE item in the SCREEN menu (42)), and the
projector will go into the FREEZE mode, which the picture is
frozen.
1.
MY SOURCE/
COMPUTER
VIDEO
DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
FREEZE
PAGE
UP
VOLUME
MAGNIFY
㧗
ON
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
1
2
To exit the FREEZE mode and restore the screen to normal,
press the FREEZE button again.
● The projector automatically exits from the FREEZE mode when some control
buttons are pressed.
● If the projector continues projecting a still image for a long time, the LCD
panel might possibly be burned in. Do not leave the projector in the FREEZE
mode for too long.
● Images might appear degraded when this function is operated, but it is not a
malfunction.
Temporarily blanking the screen
BLANK button
Press the BLANK button on the control panel or the remote
1.
control. The BLANK screen will be displayed instead of
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
the screen of input signal. Please refer to BLANK item in
ASPECT
AUTO SEARCH BLANK
SCREEN menu (40).
FREEZE
PAGE
UP
VOLUME
MAGNIFY
㧗
ON
To exit from the BLANK screen and return to the input signal
DOWN
OFF
screen, press BLANK button again.
KEYSTONE
MY BUTTON
MUTE
1
2
● The projector automatically exits from the BLANK mode
when some control buttons are pressed.
● You can change the function assigned to the BLANK
button on the control panel by the MY BUTTON function.
Please refer to MY BUTTON item in OPTION menu
(48).
BLANK button
%/$1.
0<ꢀ%87721
CAUTION ►If you wish to have a blank screen while the projector's lamp is
on, use the BLANK function above. Any other method of blocking the projection
light, such as attaching something to the lens or placing something in front of the
lens, may cause the damage to the projector.
NOTE • The sound is not connected with the BLANK screen function. If
necessary, set the volume or mute first. To display the BLANK screen and mute
the sound at one time, use AV MUTE function (48).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Using the menu function
This projector has the following menus:
PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, SECURITY and
EASY MENU.
EASY MENU consists of functions often used, and the other menus are classified
into each purpose and brought together as the ADVANCED MENU.
Each of these menus is operated using the same methods. While the projector
is displaying any menu, the MENU button on the projector works as the cursor
buttons. The basic operations of these menus are as follows.
INPUT button
ENTER button
MENU button
Cursor buttons
MENU
POSITION
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
ASPECT
AUTO SEARCH BLANK
M
A
G
N
I
F
Y
F
R
E
E
Z
E
PAGE
UP
VOLUME
ON
㧗
DOWN
OFF
KEYSTONE
MY BUTTON
MUTE
MENU
ENTER
1
2
POSITION
ENTER
MENU button
RESET
ESC
RESET
ESC
(Cursor buttons)
ESC button
RESET button
To start the MENU, press the MENU button. The MENU you last used (EASY
or ADVANCED) will appear. EASY MENU has priority to appear just after
powered on.
1.
2. In the EASY MENU
(1) Use the ▲/▼ cursor buttons to select an item to
operate. If you want to change it to the ADVANCED
MENU, select the ADVANCED MENU.
(2) Use the ◄/► cursor buttons to operate the item.
In the ADVANCED MENU
(1) Use the ▲/▼ cursor buttons to select a menu.
If you want to change it to the EASY MENU,
select the EASY MENU.
The items in the menu appear on the right side.
(2) Press the ► cursor button or ENTER button to
move the cursor to the right side. Then use the
▲/▼ cursor buttons to select an item to operate and press the ► cursor
button or ENTER button to progress. The operation menu or dialog of the
selected item will appear.
(3) Use the buttons as instructed in the OSD to operate the item.
(continued on next page)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Using the menu function (continued)
To close the MENU, press the MENU button again or select EXIT and press
the ◄ cursor button or ENTER button. Even if you do not do anything, the
dialog will automatically disappear after about 30 seconds.
3.
●
If you want to move the menu position, use the cursor buttons after pressing the
POSITION button.
● Some functions cannot be performed when a certain input port is selected, or
when a certain input signal is displayed.
● When you want to reset the operation, press RESET button on the remote
control during the operation. Note that some items (ex. LANGUAGE, VOLUME)
cannot be reset.
● In the ADVANCED MENU, when you want to return to the previous display,
press the ◄ cursor button or ESC button on the remote control.
Indication in OSD (On Screen Display)
The meanings of the general words on the OSD are as follows.
Indication
EXIT
Meaning
Selecting this word finishes the OSD menu. It's the same as
pressing the MENU button.
RETURN
Selecting this word returns the menu to the previous menu.
Selecting this word cancels the operation in the present
menu and returns to the previous menu.
CANCEL or NO
Selecting this word executes the prepared function or shifts
the menu to the next menu.
OK or YES
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EASY MENU
EASY MENU
From the EASY MENU, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons. Then
perform it according to the following table.
Item
Description
Using the ◄/► buttons switches the mode for aspect ratio.
ASPECT
See the ASPECT item in IMAGE menu ( 30).
Using the ► button executes the auto keystone function.
AUTO KEYSTONE
KEYSTONE
See the AUTO KEYSTONE item in SETUP menu
(
37).
Using the ◄/► buttons corrects the vertical keystone distortion.
See the KEYSTONE item in SETUP menu ( 37).
Using the ◄/► buttons switches the picture mode.
The picture modes are combinations of GAMMA and COLOR
TEMP settings. Choose a suitable mode according to the projected
source.
NORMAL
CINEMA
DYNAMIC
BOARD(BLACK)
ó
ó
ó
DAYTIME
WHITEBOARD
BOARD(GREEN)
ó
ó
GAMMA
COLOR TEMP
2 MID
3 LOW
NORMAL
1 DEFAULT
2 DEFAULT
3 DEFAULT
4 DEFAULT
4 DEFAULT
5 DEFAULT
6 DEFAULT
CINEMA
DYNAMIC
PICTURE MODE
1 HIGH
BOARD(BLACK)
BOARD(GREEN)
WHITEBOARD
DAYTIME
4 Hi-BRIGHT-1
5 Hi-BRIGHT-2
2 MID
6 Hi-BRIGHT-3
• When the combination of GAMMA and COLOR TEMP differs
from pre-assigned modes above, the display on the menu for the
PICTURE MODE is “CUSTOM”. Please refer to the GAMMA and
COLOR TEMP ( 27, 28) items in PICTURE menu.
• Lines or other noise might appear on the screen when this function
is operated, but it is not a malfunction.
(continued on next page)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EASY MENU
Item
Description
Using the ◄/► buttons changes the eco mode setting.
ECO MODE
See the ECO MODE item in SETUP menu ( 38).
Using the ◄/► buttons switches the mode for mirror status.
MIRROR
RESET
See the MIRROR item in SETUP menu ( 38).
Performing this item resets all of the EASY MENU items except the
FILTER TIME and LANGUAGE.
A dialog is displayed for confirmation. Selecting the OK using the
button performs resetting.
►
The usage time of the air filter is shown in the menu.
Performing this item resets the filter time which counts usage time
of the air filter.
FILTER TIME
LANGUAGE
A dialog is displayed for confirmation. Selecting the OK using the
button performs resetting.
►
See the FILTER TIME item in OPTION menu ( 47).
Using the ◄/► buttons changes the display language.
See the LANGUAGE item in SCREEN menu
(
40).
Press the
►
or ENTER button to use the menu of PICTURE,
ADVANCED MENU
EXIT
IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION or SECURITY.
Press the ◄ or ENTER button to finish the OSD menu.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE menu
PICTURE menu
From the PICTURE menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
Item
Description
Using the ◄/► buttons adjusts the brightness.
Dark Light
BRIGHTNESS
ó
Using the ◄/► buttons adjusts the contrast.
Weak Strong
CONTRAST
ó
Using the ▲/▼ buttons switches the gamma mode.
DEFAULT-1
CUSTOM-6
DEFAULT-6
CUSTOM-1
DEFAULT-2
CUSTOM-2
DEFAULT-3
CUSTOM-3
DEFAULT-4
CUSTOM-5
DEFAULT-5
CUSTOM-4
To adjust CUSTOM
Selecting a mode whose name includes CUSTOM and then
pressing the ► button or the ENTER button displays a dialog to aid
you in adjusting the mode.
This function is useful when you want to
change the brightness of particular tones.
Choose an item using the ◄/► buttons,
and adjust the level using the ▲/▼ buttons.
You can display a test pattern for checking the effect of your
adjustment by pressing the ENTER button.
Each time you press the ENTER button, the
pattern changes as below.
GAMMA
No pattern Gray scale of 9 steps
ð
Ramp Gray scale of 15 steps
The eight equalizing bars correspond to eight tone levels of the test
pattern (Gray scale of 9 steps) except the darkest in the left end.
If you want to adjust the 2nd tone from left end on the test pattern,
use the equalizing adjustment bar “1”. The darkest tone at the left
end of the test pattern cannot be controlled with any of equalizing
adjustment bar.
• Lines or other noise might appear on the
screen when this function is operated, but it
is not a malfunction.
(continued on next page)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE menu
Item
Description
Using the ▲/▼ buttons switches the color temperature mode.
1 HIGH
1 CUSTOM
2 MID
2 CUSTOM
6 CUSTOM
3 LOW
6 Hi-BRIGHT-3
5 CUSTOM
3 CUSTOM
5 Hi-BRIGHT-2
4 CUSTOM
4 Hi-BRIGHT-1
To adjust CUSTOM
Selecting a mode whose name includes
CUSTOM and then pressing the ► button
or the ENTER button displays a dialog
to aid you in adjusting the OFFSET and
GAIN of the selected mode.
COLOR TEMP
OFFSET adjustments change the color intensity
on the whole tones of the test pattern.
GAIN adjustments mainly affect color intensity
on the brighter tones of the test pattern.
Choose an item using the ◄/► buttons, and adjust the level using
the ▲/▼ buttons.
You can display a test pattern for checking the effect of your
adjustment by pressing the ENTER button.
Each time you press the ENTER button, the pattern changes as below.
No pattern Gray scale of 9 steps
ð
Ramp Gray scale of 15 steps
•
Lines or other noise might appear on the screen when
this function is operated, but it is not a malfunction.
Using the ◄/► buttons adjusts the strength of whole color.
Weak
Strong
ó
• This item can be selected only for a video, s-video and component
video signal.
COLOR
•
For an HDMI signal, this item can also be selected if either (1) or (2) applies.
(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.
(2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the
projector recognizes that it receives video signals.
Using the ◄/► buttons adjusts the tint.
Reddish
Greenish
ó
• This item can be selected only for a video, s-video and component
video signal.
TINT
•
For an HDMI signal, this item can also be selected if either (1) or (2) applies.
(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.
(2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the
projector recognizes that it receives video signals.
(continued on next page)
28
Download from Www.Somanuals.com. All Manuals Search And Download.
PICTURE menu
Item
Description
Using the ◄/► buttons adjusts the sharpness.
Weak
Strong
ó
SHARPNESS
• There may be some noise and/or the screen may flicker for a
moment when an adjustment is made. This is not a malfunction.
This projector has 4 memories for adjustment data (for all the items
of the PICTURE menu).
Selecting a function using the ▲/▼ buttons and pressing the ► or
ENTER button performs each function.
SAVE-1
SAVE-2
SAVE-3
SAVE-4
ó
ó
ó
ó
ó
LOAD-4 LOAD-3
LOAD-2
LOAD-1
ó
SAVE-1, SAVE-2, SAVE-3, SAVE-4
Performing a SAVE function saves the current adjustment data into
the memory linked in the number included in the function’s name.
• Remember that the current data being stored of a memory will be
lost by saving new data into the memory.
MY MEMORY
LOAD-1, LOAD-2, LOAD-3, LOAD-4
Performing a LOAD function loads the data from the memory linked
in the number included in the function’s name, and adjusts the
picture automatically depending on the data.
• The LOAD functions whose linked memory has no data are
skipped.
• Remember that the current adjusted condition will be lost by
loading data. If you want to keep the current adjustment, please
save it before performing a LOAD function.
• There may be some noise and the screen may flicker for a
moment when loading data. This is not malfunction.
• You can perform the LOAD function using MY BUTTONs. Please
see MY BUTTON item in OPTION menu ( 48).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
IMAGE menu
IMAGE menu
From the IMAGE menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
Item
Description
Using the ▲/▼ buttons switches the mode for aspect ratio.
For a computer signal
NORMAL
4:3
16:9
16:10
NATIVE
ó
ó
ó
ó
For an HDMI signal
NORMAL 4:3
16:9
16:10
14:9
NATIVE
ó
ó
ó
ó
ó
ASPECT
For a video signal, s-video signal or component video signal
4:3 16:9 16:10 14:9 NATIVE
ó
ó
ó
ó
For no signal
16:10 (fixed)
• The NORMAL mode keeps the original aspect ratio of the signal.
Using the ◄/► buttons adjusts the over-scan ratio.
Small (It magnifies picture)
Large (It reduces picture)
ó
• This item can be selected only for a video, s-video and component
video signal.
OVER SCAN
•
For an HDMI signal, this item can also be selected if either (1) or (2) applies.
(1) HDMI FORMAT item in the INPUT menu is set to VIDEO.
(2) HDMI FORMAT item in the INPUT menu is set to AUTO, and the
projector recognizes that it receives video signals.
(continued on next page)
30
Download from Www.Somanuals.com. All Manuals Search And Download.
IMAGE menu
Item
Description
Using the ◄/► buttons adjusts the vertical position.
Down
Up
ó
• Over-adjusting the vertical position may cause noise to appear on
the screen. If this occurs, please reset the vertical position to the
default setting. Pressing the RESET button when the V POSITION
is selected will reset the V POSITION to the default setting.
• When this function is performed on a video signal or an s-video
V POSITION
signal, the range of this adjustment depends on OVER SCAN ( 30)
setting. It is not possible to adjust when OVER SCAN is set to 10.
• This function is unavailable for a signal from the HDMI port.
Using the ◄/► buttons adjusts the horizontal position.
Right
Left
ó
•
Over-adjusting the horizontal position may cause noise to appear on
the screen. If this occurs, please reset the horizontal position to the
default setting. Pressing the RESET button when the H POSITION is
selected will reset the H POSITION to the default setting.
H POSITION
• When this function is performed on a video signal or an s-video
signal, the range of this adjustment depends on OVER SCAN ( 30)
setting. It is not possible to adjust when OVER SCAN is set to 10.
• This function is unavailable for a signal from the HDMI port.
(continued on next page)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
IMAGE menu
Item
Description
Using the ◄/► buttons adjusts the horizontal phase to eliminate flicker.
Right
Left
ó
H PHASE
• This item can be selected only for a computer signal or a
component video signal.
• This function is unavailable for a signal from the HDMI port.
Using the ◄/► buttons adjusts the horizontal size.
Small
Large
ó
• This item can be selected only for a computer signal.
• This function is unavailable for a signal from the HDMI port.
• When this adjustment is excessive, the picture may not be
displayed correctly. In such a case, please reset the adjustment
by pressing the RESET button on the remote control during this
operation.
H SIZE
• Images might appear degraded when this function is operated, but
it is not a malfunction.
Selecting this item performs the automatic adjustment feature.
For a computer signal
The vertical position, the horizontal position and the horizontal
phase will be automatically adjusted.
Make sure that the application window is set to its maximum size
prior to attempting to use this feature. A dark picture may still be
incorrectly adjusted. Use a bright picture when adjusting.
For a video signal and s-video signal
The video format best suited for the respective input signal will
be selected automatically. This function is available only when
the AUTO is selected for the VIDEO FORMAT item in the INPUT
menu ( 34). The vertical position and horizontal position will be
automatically set to the default.
For a component video signal
AUTO ADJUST
EXECUTE
The vertical position and horizontal position will be automatically set
to the default. The horizontal phase will be automatically adjusted.
• The automatic adjustment operation requires approx. 10 seconds.
Also please note that it may not function correctly with some input.
• When this function is performed for a video signal, a certain extra
such as a line may appear outside a picture.
• When this function is performed for a computer signal, a black
frame may be displayed on the edge of the screen, depending on
the PC model.
• The items adjusted by this function may vary when the FINE or
DISABLE is selected for the AUTO ADJUST item of the SERVICE
item in the OPTION menu ( 49).
32
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT menu
INPUT menu
From the INPUT menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
Item
Description
Using the ▲/▼ buttons switches the progress mode.
TV FILM OFF
ó
ó
• This function works only for a video signal, s-video signal,
component video signal (of 480i@60 or 576i@50) and an HDMI
signal (of 480i@60 or 576i@50).
PROGRESSIVE
• When TV or FILM is selected, the screen image will be sharp.
FILM adapts to the 2-3 Pull-Down conversion system. But these
may cause a certain defect (for example, jagged line) of the picture
for a quick moving object. In such a case, please select OFF, even
though the screen image may lose sharpness.
Using the ▲/▼ buttons switches the noise reduction mode.
HIGH
MID
LOW
ó
ó
VIDEO NR
• This function works only for a video signal, s-video signal,
component video signal (of 480i@60 or 576i@50) and an HDMI
signal (of 480i@60 or 576i@50).
Using the ▲/▼ buttons switches the mode for color space.
AUTO
RGB
SMPTE240
REC709
REC601
ó
ó
ó
ó
• This item can be selected only for a computer signal or a
component video signal.
COLOR SPACE
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well at some signals. In such a
case, it might be good to select a suitable mode except AUTO.
(continued on next page)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT menu
Item
Description
The video format for S-VIDEO port and VIDEO port can be set.
(1) Use the ▲/▼ buttons to
select the input port.
S-VIDEO
VIDEO
ó
(2) Using the ◄/► buttons
switches the mode for video
format.
VIDEO FORMAT
AUTO
NTSC
PAL
SECAM
ó
ó
ó
N-PAL
M-PAL
NTSC4.43
ó
ó
• This item is performed only for a video signal from the VIDEO port
or the S-VIDEO port.
• The AUTO mode automatically selects the optimum mode.
• The AUTO operation may not work well for some signals. If the
picture becomes unstable (e.g. an irregular picture, lack of color),
please select the mode according to the input signal.
Using the ▲/▼ cursor buttons switches the video format for an
input from the HDMI port.
AUTO
VIDEO
COMPUTER
ó
ó
Feature
HDMI FORMAT
AUTO
VIDEO
COMPUTER
automatically sets the optimum mode.
sets the suitable mode for DVD signals.
sets the suitable mode for computer signals.
• When the COMPUTER is selected, the functions COLOR
(PICTURE menu), TINT (PICTURE menu) and OVER SCAN
(IMAGE menu) are unavailable.
Using the ▲/▼ cursor buttons changes the digital range for input
from the HDMI port.
AUTO
NORMAL
ENHANCED
ó
ó
Feature
automatically sets the optimum mode.
ets the suitable mode for DVD signals. (16-235)
sets the suitable mode for computer signals. (0-255)
HDMI RANGE
AUTO
NORMAL
ENHANCED
s
• If the contrast of the screen image is too strong or too weak, try
finding a more suitable mode.
(continued on next page)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT menu
Item
Description
Use the ◄/► buttons to select
the computer input signal type.
AUTO SYNC ON G OFF
ó
• Selecting the AUTO mode allows you to input a sync on G signal
or component video signal from the port. To input component
video signal to the projector, an RCA to D-sub cable or adapter is
required.
COMPUTER IN
• In the AUTO mode, the picture may be distorted with certain
input signals. In such a case, remove the signal connector so that
no signal is received and select the SYNC ON G OFF, and then
reconnect the signal.
Set the frame lock function on/off for each port.
(1) Use the ▲/▼ buttons to select the input ports.
COMPUTER IN
HDMI
ó
(2) Use the ◄/► buttons to turn the
frame lock function on/off .
FRAME LOCK
ON
OFF
ó
• This item can be performed only on a signal with a vertical
frequency of 50 to 60 Hz.
• When ON is selected, moving pictures are displayed more
smoothly.
(continued on next page)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUT menu
Item
Description
The resolution for the COMPUTER IN input signals can be set on
this projector.
(1) In the INPUT menu select the RESOLUTION using the ▲/▼
buttons and press the ► button.
The RESOLUTION menu will be
displayed.
(2) In the RESOLUTION menu select the
resolution you wish to display using
the ▲/▼ buttons.
Selecting AUTO will set a resolution
appropriate to the input signal.
(3) Pressing the ► or ENTER button when
selecting a STANDARD resolution will
automatically adjust the horizontal and
STANDARD
vertical positions, clock phase and
horizontal size.
↓
The INPUT_INFORMATION dialog will be
displayed.
(4) To set a custom resolution use the ▲/▼ buttons to select
the CUSTOM and the RESOLUTION_CUSTOM box will be
RESOLUTION
displayed.
CUSTOM
Set the horizontal (HORZ) and
↓
vertical (VERT) resolutions using
the ▲/▼/◄/► buttons.
This function may not support all
resolutions.
(5) Move the cursor to OK on screen and press the ► or ENTER
button. The message “ARE YOU SURE YOU WISH TO
CHANGE RESOLUTION?” appears. To save the setting, press
the ► button.
The horizontal and vertical positions, clock phase and horizontal
size will be automatically adjusted.
The INPUT_INFORMATION dialog will be
displayed.
(6) To revert back to the previous resolution without saving
changes, move the cursor to CANCEL on screen and press the
◄ or ENTER button.
The screen will then return to the RESOLUTION menu
displaying the previous resolution.
• For some pictures, this function may not work well.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP menu
SETUP menu
From the SETUP menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
Item
Description
Selecting this item performs the Automatic keystone distortion
correction. Projector automatically corrects vertical keystone distortion
due to the (forward/backward) setup angle by itself.
This function will be executed only once when selected in the menu.
When the slant of the projector is changed, execute this function again.
• The adjustable range of this function will vary among inputs. For
some input, this function may not work well.
• When V:INVERT or H&V:INVERT is selected to the MIRROR item
in the SETUP menu, if the projector screen is inclined or angled
downward, this function may not work correctly.
• When the zoom adjustment is set to the TELE (telephoto focus),
this function may be excessive. This function should be used when
the zoom adjustment is set to the full WIDE (wide-angle focus)
whenever possible.
AUTO KEYSTONE
• When the projector is placed on the level (about ±4°), this function
may not work.
• When the projector is inclined to near ±30 degree or over, this
function may not work well.
• This function will be unavailable when the Transition Detector is
on ( 54).
Using the ◄/► buttons corrects the vertical keystone distortion.
Shrink the bottom of the image
Shrink the top of the image
ó
• The adjustable range of this function will vary among inputs. For
some input, this function may not work well.
KEYSTONE
• This function will be unavailable when the Transition Detector is
on ( 54).
Using the ▲/▼ buttons turns on/off the AUTO ECO MODE.
ON
OFF
ó
AUTO ECO
MODE
• When ON is selected, the projector will always be set to Eco mode
at start-up regardless of the ECO MODE ( 38) setting. An OSD
message “AUTO ECO MODE” will be displayed for tens of seconds
when the projector starts with this function activated.
(continued on next page)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP menu
Item
Description
Using the ▲/▼ buttons changes the eco mode setting.
NORMAL
ECO
ó
ECO MODE
MIRROR
• When the ECO is selected, acoustic noise and screen brightness
are reduced.
Using the ▲/▼ buttons switches the mode for mirror status.
NORMAL
H:INVERT
V:INVERT
H&V:INVERT
ó
ó
ó
If the Transition Detector is on and MIRROR status is changed,
TRANSITION DETECTOR ON alarm ( 54) will be displayed when
projector is restarted after the AC power is turned off.
Using ▲/▼ buttons switches the standby mode setting between
NORMAL and SAVING.
NORMAL
SAVING
ó
• When SAVING is selected and the projector is in the standby
state, the power consumption is lowered with some functional
restrictions as below.
STANDBY MODE
- The RS-232C communication control is disabled except turning
the projector on and changing the STANDBY MODE setting.
- The STANDBY of the MONITOR OUT (below) is invalid, and no
signal is output from the MONITOR OUT port.
- The AUDIO OUT STANDBY of the AUDIO SOURCE ( 39) is
invalid, and no signal is output from the AUDIO OUT ports ( 5).
While the image signal from the input port chosen in step (1) is
projected, the image signal from the input port selected in step (2)
is output to MONITOR OUT port.
(1) Choose a picture input port using
▲/▼ buttons.
Choose STANDBY to select the
picture output in the standby mode.
(2) Select the output signal from the
MONITOR OUT port using ◄/►
buttons.
MONITOR OUT
Select OFF to disable the MONITOR
OUT port for the input port or standby
mode chosen in the step (1).
• If you have changed the setting of STANDBY, it applies only to
the current standby mode, NORMAL or SAVING, selected under
STANDBY MODE, without changing the setting of the other mode.
The factory settings are as follows:
- COMPUTER IN for the NORMAL mode of STANDBY MODE
- OFF for the SAVING mode of STANDBY MODE
38
Download from Www.Somanuals.com. All Manuals Search And Download.
AUDIO menu
AUDIO menu
From the AUDIO menu, items shown in the table
below can be performed. Select an item using the
▲/▼ cursor buttons, and press the ► cursor button
or the ENTER button to execute the item. Then
perform it according to the following table.
Item
Description
Using the ◄/► buttons adjusts the volume.
Low High
VOLUME
ó
Using the ▲/▼ buttons turns on/off the built-in speaker.
ON OFF
SPEAKER
ó
When OFF is selected, the built-in speaker does not work.
While the image signal from the input port chosen in step (1) is
projected, the audio signal from the input port selected in step
(2) is output to both the AUDIO OUT port and built-in speaker of
this projector. However, the built-in speaker does not work when
SPEAKER is set to OFF.
(1) Choose a picture input port using
the ▲/▼ buttons.
Choose AUDIO OUT STANDBY
to select the sound output in the
standby mode.
(2) Select one of the AUDIO IN ports
using ◄/► buttons.
Select to mute the sound from the input port or in the standby
mode chosen in the step (1).
AUDIO SOURCE
• In the AUDIO SOURCE window, “H” symbolizes the audio signal
from the HDMI port. It can be selected only for the picture input
from the HDMI port.
• C.C. (Closed Caption) is automatically activated when is selected
and an input signal containing C.C. is received. This function is
available only when the signal is NTSC for VIDEO or S-VIDEO,
or 480i@60 for COMPUTER IN, and when AUTO is selected for
DISPLAY in the C.C. menu under the SCREEN menu ( 45).
• AUDIO OUT STANDBY is automatically set to OFF when SAVING
is selected for the STANDBY MODE item in the SETUP menu.
Using the ▲/▼ buttons switches the mode for the HDMI audio.
Check each of the two modes provided and select the suitable one
for your HDMI audio device.
HDMI AUDIO
1
2
ó
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREEN menu
SCREEN menu
From the SCREEN menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item. Then perform it according to the
following table.
Item
Description
Using the ▲/▼/◄/► buttons switches the OSD (On Screen
Display) language.
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
ó
ó
ó
LANGUAGE
(shown in the LANGUAGE dialog)
Press the ENTER or INPUT button to save the language setting.
Using the ▲/▼/◄/► buttons adjusts the menu position.
MENU POSITION To quit the operation, press the MENU button on the remote control
or keep no operation for about 10 seconds.
Using the ▲/▼ buttons switches the mode for the blank screen.
The blank screen is a screen for the temporarily blanking feature
(
22). It is displayed by pressing the BLANK button on the remote
control.
MyScreen
ORIGINAL
BLUE
WHITE
BLACK
ó
ó
ó
ó
BLANK
MyScreen : Screen can be registered by the MyScreen item ( 41).
ORIGINAL : Screen preset as the standard screen.
BLUE, WHITE, BLACK : Plain screens in each color.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL
screen will change to the plain black screen after several minutes.
Using the ▲/▼ buttons switches the mode for the start-up screen.
The start-up screen is a screen displayed when no signal or an
unsuitable signal is detected.
MyScreen
ORIGINAL
OFF
ó
ó
MyScreen : Screen can be registered by the MyScreen item ( 41).
ORIGINAL : Screen preset as the standard screen.
START UP
OFF : Plain black screen.
• To avoid remaining as an afterimage, the MyScreen or ORIGINAL
screen will change to the BLANK screen ( 22) after several
minutes. If also the BLANK screen is the MyScreen or ORIGINAL,
the plain black screen is instead used.
• When the ON is selected to the MyScreen PASSWORD item in
the SECURITY menu ( 52), the START UP is fixed to MyScreen.
(continued on next page)
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREEN menu
Item
Description
This item allows you to capture an image for use as a MyScreen
image which can be used as the BLANK screen and START UP
screen. Display the image you want to capture before executing the
following procedure.
1. Selecting this item displays a dialog
titled “MyScreen”. It will ask you if
you start capturing an image from
the current screen.
Please wait for the target image to be displayed, and press the
ENTER or INPUT button when the image is displayed. The image
will freeze and the frame for capturing will appear.
To stop performing, press the RESET button on the remote
control.
2. Using the ▲/▼/◄/► buttons adjusts
the frame position.
Please move the frame to the position
of the image which you want to use. The
frame may not be able to be moved for
some input signals.
MyScreen
To start registration, press the ENTER
or INPUT button on the remote control.
To restore the screen and return to the previous dialog, press the
RESET button on the remote control.
Registration takes several minutes.
When the registration is completed, the registered screen and the
following message is displayed for several seconds:
“MyScreen registration is finished.”
If the registration failed, the following message is displayed:
“A capturing error has occurred. Please try again.”
• This function cannot be selected when the ON is selected to the
MyScreen Lock item ( 42).
• This function cannot be selected when the ON is selected to the
MyScreen PASSWORD item in SECURITY menu ( 52).
• This function is unavailable for a signal from the HDMI port.
(continued on next page)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREEN menu
Item
Description
Using the ▲/▼ buttons turns on/off the MyScreen lock function.
ON
OFF
ó
When the ON is selected, the item MyScreen is locked. Use this
function for protecting the current MyScreen.
MyScreen Lock
• This function cannot be selected when the ON is selected to the
MyScreen PASSWORD item in SECURITY menu ( 52).
Using the ▲/▼ buttons turns on/off the message function.
ON
OFF
ó
When the ON is selected, the following message function works.
“AUTO IN PROGRESS” while automatically adjusting
“NO INPUT IS DETECTED”
“SYNC IS OUT OF RANGE”
“INVALID SCAN FREQ.”
“NOT AVAILABLE”
“Searching….” while searching for the input
“Detecting….” while an input signal is detected
“AUTO ECO MODE” while starting up with AUTO ECO MODE
The indication of the input signal displayed by changing
The indication of the aspect ratio displayed by changing
The indication of the PICTURE MODE displayed by changing
The indication of the MY MEMORY displayed by changing
The indication of “FREEZE” and “II” while freezing the screen by
pressing the FREEZE button.
MESSAGE
The indication of the TEMPLATE displayed by changing.
• When the OFF is selected, please remember if the picture is
frozen. Do not mistake freezing for a malfunction ( 22).
(continued on next page)
42
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREEN menu
Item
Description
Each input port for this projector can have a name applied to it.
(1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE
NAME and press the ► or ENTER button.
The SOURCE NAME menu will be displayed.
(2) Use the ▲/▼ buttons on the SOURCE
NAME menu to select the port to be
named and press the ► button. The
SOURCE NAME dialog will be displayed.
Right side of the menu is blank until a
name is specified.
(3) Select an icon you'd like to assign to the
port in the SOURCE NAME dialog. The
name assigned to the port will also be
automatically switched according to your
icon selection. Press the ► or ENTER
button to determine your icon selection.
(4) Select a number you'd like to assign for
the port along with the icon. You can
select the number either from blank (no
number assigned), 1, 2, 3, or 4.
(5) If you'd like to modify the name assigned
to the port, select CUSTOM NAME and
press the ► button.
SOURCE NAME
(6) The current name will be displayed on
the first line. Use the ▲/▼/◄/► buttons
and the ENTER or INPUT button to
select and enter characters. To erase 1
character at one time, press the RESET
button or press the ◄ and INPUT button
at the same time. Also if you move the
cursor to DELETE or ALL CLEAR on
screen and press the ENTER or INPUT
button, 1 character or all characters will
be erased. The name can be a maximum
of 16 characters.
(7) To change an already inserted character,
press the ▲ button to move the cursor to the
first line, and use the ◄/► buttons to move
the cursor on the character to be changed.
After pressing the ENTER or INPUT button, the character is
selected. Then, follow the same procedure as described at the
item (6) above.
(8) To finish entering text, move the cursor to the OK on screen and
press the ►, ENTER or INPUT button. To revert to the previous
name without saving changes, move the cursor to the CANCEL
on screen and press the ◄, ENTER or INPUT button.
(continued on next page)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREEN menu
Item
Description
Using the ▲/▼ buttons switches the mode for the template screen.
Press the ► button to display the selected template, and press the
◄ button to close the displayed screen.
The last selected template is displayed when the MY BUTTON
allocated to the TEMPLATE function is pressed ( 48).
TEST PATTERN
DOT-LINE1
DOT-LINE2
DOT-LINE3
ó
ó
ó
MAP2
MAP1
CIRCLE2
CIRCLE1
DOT-LINE4
ó
ó
ó
ó
You can turn a map upside down and scroll it horizontally when MAP1
or MAP2 is selected. To invert or scroll the map, display the guidance
by pressing the RESET button on the remote control three seconds or
more when MAP1 or MAP2 appears.
TEMPLATE
While the guidance is displayed:
• Press the ▲ cursor button and then press the ENTER or INPUT
button to place the Northern Hemisphere on the top.
• Press the ▼ cursor button and then press the ENTER or INPUT
button to place the Southern Hemisphere on the top.
• Press the ◄/► cursor button and then press the ENTER or
INPUT button to scroll the map horizontally.
(continued on next page)
44
Download from Www.Somanuals.com. All Manuals Search And Download.
SCREEN menu
Item
Description
The C.C. is the function that displays a
transcript or dialog of the audio portion of
a video, files or other presentation or other
relevant sounds. It is required to have NTSC
format video or 480i@60 format component
video source supporting C.C. feature to
utilize this function.
It may not work properly, depending on equipment or signal source.
In this case, please turn off the Closed Caption.
DISPLAY
Select Closed Caption DISPLAY setting from following options
using ▲/▼ buttons.
AUTO
ON
OFF
ó
ó
AUTO : Closed Caption automatically displays when the volume
is muted.
ON : Closed Caption is on.
OFF : Closed Caption is off.
• The caption is not displayed when the OSD menu is active.
• The Closed Caption is the function to display the dialogue,
narration, and / or sound effects of a television program or other
video sources. The Closed Caption availability is depending upon
broadcaster and/or content.
C.C.
(Closed Caption)
MODE
Select Closed Caption MODE setting from following options using
▲/▼ buttons.
CAPTIONS
TEXT
ó
CAPTIONS : Display Closed Caption.
TEXT : Display Text data, which is for additional information such
as news reports or a TV program guide. The information
covers the entire screen. Not all of the C.C. program has
Text information.
CHANNEL
Select Closed Caption CHANNEL from following options using ▲/▼
buttons.
1
2
3
4
ó
ó
ó
1: Channel 1, primary channel / language
2: Channel 2
3: Channel 3
4: Channel 4
The channel data may vary, depending on the content. Some
channel might be used for secondary language or empty.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTION menu
OPTION menu
From the OPTION menu, items shown in the table
below can be performed.
Select an item using the ▲/▼ cursor buttons, and
press the ► cursor button or ENTER button to
execute the item, except for the items LAMP TIME
and FILTER TIME. Then perform it according to the
following table.
Item
Description
Using the ▲/▼ buttons turns on/off the automatic signal search
function.
ON
OFF
ó
When the ON is selected, detecting no signal automatically cycles
through input ports in the following order. The search is started from
the current port. Then when an input is found, the projector will stop
searching and display the image.
AUTO SEARCH
COMPUTER IN
HDMI
ð
VIDEO
S-VIDEO
Using the ▲/▼ buttons turns on/off the automatic keystone function.
ON OFF
ó
ON : Automatic keystone distortion correction will be executed
whenever changing the slant of the projector.
OFF : This function is disabled. Please execute the AUTO
KEYSTONE in the SETUP menu for automatic keystone
distortion correction.
AUTO
KEYSTONE
• When the projector is suspended from the ceiling this feature will
not function properly so select the OFF.
• This function will be unavailable when the Transition Detector is
on
(
54).
Using the ▲/▼ buttons turns on/off the DIRECT POWER ON
function.
ON
OFF
ó
When set to the ON, the lamp in projector will be automatically
turned on without the usual procedure ( 13), only when the
projector is supplied with the power after the power was cut while
the lamp was on.
• This function does not work as long as the power has been
supplied to the projector while the lamp is off.
DIRECT POWER
ON
•
After turning the lamp on by the DIRECT POWER ON function,
if neither input nor operation is detected for about 30 minutes, the
projector is turned off, even though the AUTO POWER OFF function
(
47) is disabled.
(continued on next page)
46
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTION menu
Item
Description
Using the ▲/▼ buttons adjusts the time to count down to
automatically turn the projector off.
Long (max. 99 minutes)
Short (min. 0 minute = DISABLE)
ó
When the time is set to 0, the projector is not turned off automatically.
When the time is set to 1 to 99, and when the passed time with no-
signal or an unsuitable signal reaches at the set time, the projector
lamp will be turned off.
AUTO POWER
OFF
If one of the projector's buttons or the remote control buttons
is pressed or one of the commands (except get commands) is
transmitted to the CONTROL port during the corresponding time,
projector will not be turned off.
Please refer to the section “Turning off the power” ( 13).
The lamp time is the usage time of the lamp, counted after the last
resetting. It is shown in the OPTION menu.
Pressing the RESET button on the remote control or the ► button
of the projector displays a dialog.
To reset the lamp time, select the OK using the ► button.
LAMP TIME
CANCEL OK
ð
• Please reset the lamp time only when you have replaced the lamp,
for a suitable indication about the lamp.
• For the lamp replacement, see the section "Replacing the lamp"
(
57, 58).
The filter time is the usage time of the air filter, counted after the last
resetting. It is shown in the OPTION menu.
Pressing the RESET button on the remote control or the ► button
of the projector displays a dialog.
To reset the filter time, select the OK using the ► button.
FILTER TIME
CANCEL OK
ð
•
Please reset the filter time only when you have cleaned or replaced
the air filter, for a suitable indication about the air filter.
• For the air filter cleaning, see the section “Cleaning and replacing
the air filter” ( 59, 60).
(continued on next page)
47
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTION menu
Item
Description
You can use this item to assign one of the following functions to the
BLANK button on the control panel ( 5) and the MY BUTTON 1/2
buttons on the remote control ( 6).
(1) Choose a button to assign a function from BLANK, MY
BUTTON-1 and MY BUTTON-2. Use the ▲/▼ buttons to select
the desired button on the menu and press the ► button.
(2) Then using the ▲/▼/◄/► buttons sets one of the following
functions to the chosen button. Press the ENTER or INPUT
button to save the setting.
• COMPUTER IN: Sets port to COMPUTER IN.
• HDMI: Selects input from HDMI port.
• S-VIDEO: Sets port to S-VIDEO.
• VIDEO: Sets port to VIDEO.
• INFORMATION: Displays the INPUT_INFORMATION ( 50) or
the SYSTEM_INFORMATION or nothing.
• AUTO KEYSTONE : Performs automatic keystone distortion
correction ( 37).
• MY MEMORY: Loads one of adjustment data stored ( 29).
When more than one data are saved, the adjustment
changes every time the MY BUTTON is pressed.
When no data is saved in memory, the
dialog "No saved data" appears.
MY BUTTON
When the current adjustment is not
saved to memory, the dialog as shown in
the right appears.
If you want to keep the current adjustment, please press
the ► button to exit. Otherwise loading a data will overwrite the
current adjusted condition.
• PICTURE MODE: Changes the PICTURE MODE ( 25).
• FILTER RESET: Displays the filter time reset confirmation dialogue
(
47).
• TEMPLATE: Makes the template pattern selected to the
TEMPLATE item ( 44) appear or disappear.
• AV MUTE: Turns the picture and audio on/off.
• RESOLUTION: Turns on/off the RESOLUTION dialog. ( 36)
• ECO MODE: Turns on/off the ECO MODE dialog. ( 38)
• BLANK: Turns on/off the blank function. (BLANK only)
• FREEZE: Turns on/off the freeze function. (BLANK only)
• VOLUME: Turns on/off the volume dialog. (BLANK only)
• AUTO: Performs the automatic adjustment function. (BLANK only)
Using ▲/▼ buttons selects the picture input port to be selected with
pressing the MY SOURCE/DOC.CAMERA button on the remote
control.
MY SOURCE
Select the picture input that is connected with a document camera.
COMPUTER IN
HDMI
ó
VIDEO
S-VIDEO
ó
(continued on next page)
48
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTION menu
Item
Description
Selecting this item displays the SERVICE
menu.
Select an item using the ▲/▼ buttons,
and press the ► button or the ENTER
button on the remote control to execute
the item.
FAN SPEED
Using the ▲/▼ buttons switches the rotation speed of the cooling
fans. The HIGH is the mode for use at highlands etc. Note that the
projector is noisier when the HIGH is selected.
HIGH
NORMAL
ó
AUTO ADJUST
Using the ▲/▼ buttons to select one of the mode. When the
DISABLE is selected, the automatic adjustment feature is disabled.
FINE
FAST
DISABLE
ó
ó
FINE: Finer tuning including H.SIZE adjustment.
FAST: Faster tuning, setting H.SIZE to prearranged data for the
input signal.
•
Depending on conditions, such as input image, signal cable to the
projector, environment around the projector, etc., the automatic adjustment
may not work correctly. In such a case, please choose DISABLE to disable
the automatic adjustment, and make adjustment manually.
SERVICE
GHOST
1. Select a color element of ghost using
the ◄/► buttons.
2. Adjust the selected element using the
▲/▼ buttons to disappear ghost.
FILTER MESSAGE
Use the ▲/▼ button to set the timer for notifying by the message
when to replace the filter unit
100h
200h
500h
1000h
3000h
2000h
4000h
ó
ó
ó
ó
ó
ó
5000h
OFF
ó
ó
After choosing an item except OFF, the message “REMINDER
***HRS PASSED .....” will appear after the timer reaches the interval
time set by this feature ( 62).
When the OFF is chosen, the message will not appear. Utilize
this feature to keep the air filter clean, setting the suitable time
according to your environment of this projector.
•
Please take care of the filter unit periodically, even if there is no message. If the
air filter becomes to be blocked by dust or other matter, the internal temperature
will rise, which could cause malfunction, or reduce the lifetime of the projector.
• Please be careful with the operating environment of the projector
and the condition of the filter unit.
(continued on next page)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTION menu
Item
Description
KEY LOCK
Using the ▲/▼ buttons turns on/off the key lock feature. When ON
is selected, the buttons on the projector except the STANDBY/ON
button are locked.
ON
OFF
ó
• Please use this function to prevent tampering or accidental
operation. This function does not have any effect on the remote
control.
INFORMATION
Selecting this item displays a dialog titled “INPUT_INFORMATION”.
It shows the information about the current input.
SERVICE
(continued)
• The “FRAME LOCK” message on the dialog means the frame lock
function is working.
• This item can't be selected for no signal and sync out.
• When the MY TEXT DISPLAY is set to ON, the MY TEXT is
displayed together with the input information in the INPUT_
INFORMATION box ( 56).
FACTORY RESET
Selecting OK using the ► button performs this function. By
this function, all the items in all of menus will collectively return
to the initial setting. Note that the LAMP TIME, FILTER TIME,
LANGUAGE, FILTER MESSAGE, SECURITY settings, and others
are not reset.
CANCEL OK
ð
50
Download from Www.Somanuals.com. All Manuals Search And Download.
SECURITY menu
SECURITY menu
This projector is equipped with security functions.
From the SECURITY menu, items shown in the table
below can be performed.
To use SECURITY menu: User registration is required
before using the security functions.
Enter the SECURITY menu
1. Use the ▲/▼ buttons on the SECURITY menu to select ENTER PASSWORD and press the ►
button. The ENTER PASSWORD box will be displayed.
2. Use the ▲/▼/◄/► buttons to enter the registered password.
The factory default password is 4610. This password can be
changed ( below). Move the cursor to the right side of the ENTER
PASSWORD box and press the ► button to display the SECURITY
menu.
• It is strongly recommended the factory default password to be
changed as soon as possible.
• If an incorrect password is input, the ENTER PASSWORD box
will be displayed again. If incorrect password is input 3 times, the
projector will turn off. Afterwards the projector will turn off every time
an incorrect password is input.
3. Items shown in the table below can be performed.
If you have forgotten your password
(1). While the ENTER PASSWORD box is displayed, press and hold
the RESET button on the remote control for about 3 seconds or
press and hold the INPUT button for 3 seconds while pressing the
► button on the projector.
(2). The 10 digit Inquiring Code will be displayed. Contact your dealer
with the 10 digit Inquiring Code. Your password will be sent after
your user registration information is confirmed.
• If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will
close. If necessary, repeat the process from (1).
Item
Description
(1) Use the ▲/▼ buttons on the SECURITY menu
to select SECURITY PASSWORD CHANGE
and press the ► button to display the ENTER
NEW PASSWORD box.
(2) Use the ▲/▼/◄/► buttons to enter the new password.
(3) Move the cursor to the right side of the
ENTER NEW PASSWORD box and press the
► button to display the NEW PASSWORD
AGAIN box, enter the same password again.
(4) Move the cursor to the right side of the NEW
PASSWORD AGAIN box and press the ►
button and the NOTE NEW PASSWORD box
will be displayed for about 30 seconds, please
make note of the password during this time.
SECURITY
PASSWORD
CHANGE
Pressing the ENTER button on the remote control or
►
button on the
projector will close the NOTE NEW PASSWORD box.
• Please do not forget your password.
(continued on next page)
51
Download from Www.Somanuals.com. All Manuals Search And Download.
SECURITY menu
Item
Description
The MyScreen PASSWORD function can be used to prohibit access to the
MyScreen function and prevent the currently registered MyScreen image
from being overwritten.
1 Turning on the MyScreen PASSWORD
1-1 Use the ▲/▼ buttons on the SECURITY menu to
select MyScreen PASSWORD and press the ►
button to display the MyScreen PASSWORD on/
off menu.
1-2 Use the ▲/▼ buttons on the MyScreen
PASSWORD on/off menu to select ON.
The ENTER NEW PASSWORD box (small)
will be displayed.
ENTER NEW PASSWORD
box (small)
1-3 Use the ▲/▼/◄/► buttons to enter the
password. Move the cursor to the right side
of the ENTER NEW PASSWORD box (small)
and press the ► button to display the NEW
PASSWORD AGAIN box, enter the same
PASSWORD again.
1-4 Move the cursor to the right side of the
NEW PASSWORD AGAIN box and press
the ► button to display the NOTE NEW
PASSWORD box for about 30 seconds,
please make note of the password during
this time.
Pressing the ENTER button on the remote control or ► button on the
MyScreen
PASSWORD
projector will return to MyScreen PASSWORD on/off menu.
When a password is set for MyScreen:
The MyScreen registration function (and menu) will be unavailable.
The MyScreen Lock menu will be unavailable.
The START UP setting will be locked on MyScreen (and the menu will be
•
•
•
unavailable).
Turning the MyScreen PASSWORD off will allow normal operation of these
functions.
Please do not forget your MyScreen PASSWORD.
•
2 Turning off the MyScreen PASSWORD
2-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off
menu.
2-2 Select OFF to display the ENTER
PASSWORD box (large). Enter the registered
password and the screen will return to the
MyScreen PASSWORD on/off menu.
ENTER PASSWORD box
(large)
If an incorrect PASSWORD is input, the menu will
close. If necessary, repeat the process from 2-1.
3 If you have forgotten your password
3-1 Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off
menu.
3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit
Inquiring Code will be displayed inside the box.
3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will
be sent after your user registration information is confirmed.
(continued on next page)
52
Download from Www.Somanuals.com. All Manuals Search And Download.
SECURITY menu
Item
Description
PIN LOCK is a function which prevents the projector from being used unless
a registered Code is input.
1 Turning on the PIN LOCK
1-1 Use the ▲/▼ buttons on the SECURITY menu
to select PIN LOCK and press the ► button or
the ENTER button to display the PIN LOCK on/
off menu.
1-2 Use the ▲/▼ buttons on the PIN LOCK on/
off menu to select ON and the Enter PIN
Code box will be displayed.
1-3 Input a 4 part PIN code using the ▲/▼/◄/►,
COMPUTER or INPUT button.
The PIN Code again box will appear. Reenter
the same PIN code. This will complete the PIN
code registration.
If there is no key input for about 55 seconds
while the Enter PIN Code box or the PIN Code again box is displayed,
the menu will close. If necessary, repeat the process from 1-1.
•
Afterwards, anytime the projector is restarted after AC power is turned off
the Enter PIN Code box will be displayed. Enter the registered PIN code.
The projector can be used after entering the registered PIN code. If an
incorrect PIN code is input, the Enter PIN code box will be displayed again.
If an incorrect PIN Code is input 3 times, the projector will turn off.
Afterwards the projector will turn off every time an incorrect PIN code is
input. The projector will also turn off if there is no key input for about 5
minutes while the Enter PIN code box is displayed.
PIN LOCK
This function will activate only when the projector is started after AC power
is turned off.
Please do not forget your PIN code.
•
2 Turning off the PIN LOCK
2-1 Follow the procedure in 1-1 to display the PIN LOCK on/off menu.
2-2 Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be
displayed.
Enter the registered PIN code to turn the PIN LOCK function off.
If an incorrect PIN Code is input 3 times, the menu will close.
3 If you have forgotten your PIN Code
3-1 While the Enter PIN Code box is displayed, press and hold the RESET
button for three seconds or press and hold the INPUT button for 3
seconds while pressing the ► button on the projector.
The 10 digit Inquiring Code will be displayed.
If there is no key input for about 5 minutes
while the Inquiring Code is displayed, the
•
projector will turn off.
3-2 Contact your dealer with the 10 digit Inquiring Code. Your PIN Code will
be sent after your user registration information is confirmed.
(continued on next page)
53
Download from Www.Somanuals.com. All Manuals Search And Download.
SECURITY menu
Item
Description
If this function is set to ON when the vertical angle of
the projector or MIRROR setting at which the projector
is turned on is different than the previously recorded, the
TRANSITION DETECTOR ON alarm will be displayed
and the projector will not display the input signal.
• To display the signal again, set this function OFF.
• After about 5 minutes of displaying the TRANSITION DETECTOR ON
alarm, the lamp will turn off.
• Keystone adjustment feature has been prohibited as long as the Transition
Detector function is on.
1 Turning on the TRANSITION DETECTOR
1-1 Use the ▲/▼ buttons on the SECURITY menu
to select TRANSITION DETECTOR and press
the ► or the ENTER button to display the
TRANSITION DETECTOR on/off menu.
1-2 Use the ▲/▼ buttons on the TRANSITION
DETECTOR on/off menu to select ON. Select
ON and the current angle and MIRROR
setting will be recorded. The ENTER NEW
PASSWORD box (small) will be displayed.
1-3 Use the ▲/▼/◄/► buttons to enter a
password. Move the cursor to the right side
of the ENTER NEW PASSWORD box (small)
and press the ► button to display the NEW
PASSWORD AGAIN box, enter the same
password again.
1-4 Move the cursor to the right side of the NEW
PASSWORD AGAIN box and press the ►
button to display the NOTE NEW PASSWORD
box for about 30 seconds, please make note
of the password during this time.
ENTER NEW PASSWORD
box (small)
TRANSITION
DETECTOR
Pressing the ENTER button on the remote control or the
►
button on the
projector will return to the TRANSITION DETECTOR on/off menu.
• Please do not forget your TRANSITION DETECTOR password.
• This function will activate only when the projector is started after turning off
the AC power.
• This feature may not function properly if the projector is not in a stable
position when ON is selected.
2 Turning off the TRANSITION DETECTOR
2-1 Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.
2-2 Select OFF to display the ENTER
PASSWORD box (large). Enter the registered
password and the screen will return to the
TRANSITION DETECTOR on/off menu.
If an incorrect password is input, the menu will
close. If necessary, repeat the process from 2-1.
ENTER PASSWORD box
(large)
3 If you have forgotten your password
3-1 Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.
3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit
Inquiring Code will be displayed inside the box.
3-3 Contact your dealer with the 10 digit Inquiring Code. Your password will
be sent after your user registration information is confirmed.
(continued on next page)
54
Download from Www.Somanuals.com. All Manuals Search And Download.
SECURITY menu
Item
Description
The MY TEXT PASSWORD function can prevent the MY TEXT from being
overwritten. When the password is set for the MY TEXT;
• The MY TEXT DISPLAY menu will be unavailable, which can prohibit
changing the DISPLAY setting.
• The MY TEXT WRITING menu will be unavailable, which can prevent the
MY TEXT from being overwritten.
1 Turning on the MY TEXT PASSWORD
1-1 Use the ▲/▼ buttons on the SECURITY menu to
select the MY TEXT PASSWORD and press the
► button to display the MY TEXT PASSWORD
on/off menu.
1-2 Use the ▲/▼ buttons on the MY TEXT
PASSWORD on/off menu to select ON. The
ENTER NEW PASSWORD box (small) will
be displayed.
1-3 Use the ▲/▼/◄/► buttons to enter the
password. Move the cursor to the right side
of the ENTER NEW PASSWORD box (small)
and press the ► button to display the NEW
PASSWORD AGAIN box, and then enter the
same password again.
ENTER NEW PASSWORD
box (small)
1-4 Move the cursor to the right side of the
NEW PASSWORD AGAIN box and press
► button to display the NOTE NEW
PASSWORD box for about 30 seconds,
then please make note of the password
during this time.
MY TEXT
PASSWORD
Pressing the ENTER button on the remote control or ► button on the
projector will return to the MY TEXT PASSWORD on/off menu.
2 Turning off the MY TEXT PASSWORD
2-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off
menu.
2-2 Select OFF to display the ENTER
PASSWORD box (large). Enter the
registered password and the screen will
return to the MY TEXT PASSWORD on/off
menu.
ENTER PASSWORD box
(large)
If an incorrect password is input, the menu will
close. If necessary, repeat the process from 2-1
3 If you have forgotten your password
3-1 Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off
menu.
3-2 Select OFF to display the ENTER PASSWORD box (large). The 10 digit
inquiring code will be displayed inside the box.
3-3 Contact your dealer with the 10 digit inquiring code. Your password will
be sent after your user registration information is confirmed.
(continued on next page)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
SECURITY menu
Item
Description
(1) Use the ▲/▼ buttons on the SECURITY menu to
select the MY TEXT DISPLAY and press the ►
button to display the MY TEXT DISPLAY on/off
menu.
(2) Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select
on or off.
ON
OFF
ó
MY TEXT
DISPLAY
When it is set ON, the MY TEXT will be displayed
on the START UP screen and the INPUT_
INFORMATION when the INFORMATION on the
SERVICE menu is chosen.
• This function is available only when the MY TEXT
PASSWORD function is set to the OFF.
(1) Use the ▲/▼ buttons on the
SECURITY menu to select the MY
TEXT WRITING and press the ►
button. The MY TEXT WRITING dialog
will be displayed.
(2) The current MY TEXT will be displayed
on the first 3 lines. If not yet written, the
lines will be blank.
Use the ▲/▼/◄/► buttons and the
ENTER or INPUT button to select and
enter characters. To erase 1 character
at one time, press the RESET button
or press the ◄ and INPUT button at
the same time. Also if you move the
cursor to DELETE or ALL CLEAR on
screen and press the ENTER or INPUT
button, 1 character or all characters will
be erased. The MY TEXT can be input
up to 24 characters on each line.
MY TEXT
WRITING
(3) To change an already inserted
character, press the ▲/▼ button to
move the cursor to one of the first 3
lines, and use the ◄/► buttons to
move the cursor on the character to be
changed.
After pressing the ENTER or INPUT button, the character is selected.
Then, follow the same procedure as described at the item (2) above.
(4) To finish entering text, move the cursor to the OK on screen and press
the ►, ENTER or INPUT button. To revert to the previous MY TEXT
without saving changes, move the cursor to the CANCEL on screen and
press the ◄, ENTER or INPUT button.
The MY TEXT WRITING function is available only when the MY TEXT
PASSWORD function is set to OFF.
•
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Maintenance
Replacing the lamp
A lamp has finite product life. Using the lamp for long periods of time could cause
the pictures darker or the color tone poor. Note that each lamp has a different
lifetime, and some may burst or burn out soon after you start using them.
Preparation of a new lamp and early replacement are recommended. To prepare
a new lamp, make contact with your dealer and tell the lamp type number.
Type number : 456-8789H
Lamp cover
Replacing the lamp
Turn the projector off, and unplug the power cord.
Allow the projector to cool for at least 45 minutes.
1.
Prepare a new lamp. If the projector is mounted on a
ceiling, or if the lamp has broken, also ask the dealer to
replace the lamp.
2.
In case of replacement by yourself, follow the following procedure.
3
Loosen the screw (marked by arrow) of the lamp
cover and then slide and lift the lamp cover to the
side to remove it.
Loosen the 2 screws (marked by arrow) of the
lamp, and slowly pick up the lamp by the handle.
Never loosen any other screws.
Insert the new lamp, and retighten firmly the
2 screws of the lamp that are loosened in the
previous process to lock it in place.
While putting the interlocking parts of the lamp cover
and the projector together, slide the lamp cover back in
place. Then firmly fasten the screw of the lamp cover.
3.
4.
5.
6.
㧠
㧡
Handle
Turn the projector on and reset the lamp time using
the LAMP TIME item in the OPTION menu.
(1) Press the MENU button to display a menu.
(2) Point at the ADVANCED MENU in the menu using
the ▼/▲ button, then press the ► button.
6
7.
(3) Point at the OPTION in the left column of the menu
using the ▼/▲ button, then press the ► button.
(4) Point at the LAMP TIME using the ▼/▲ button, then press the ► button. A dialog will appear.
(5) Press the ► button to select “OK” on the dialog. It performs resetting the lamp time.
CAUTION ►Do not touch any inner space of the projector, while the lamp
is taken out.
NOTE • Please reset the lamp time only when you have replaced the lamp,
for a suitable indication about the lamp.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Replacing the lamp (continued)
Lamp warning
HIGH TEMPERATURE
HIGH PRESSURE
HIGH VOLTAGE
WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp
can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or
worn over time. Note that each lamp has a different lifetime, and some may burst or
burn out soon after you start using them. In addition, if the bulb bursts, it is possible
for shards of glass to fly into the lamp housing, and for gas containing mercury and
dust containing fine particles of glass to escape from the projector’s vent holes.
►About disposal of a lamp: This product contains a mercury lamp; do not put
it in a trash. Dispose of it in accordance with environmental laws.
For more information, call your dealer.
• If the lamp should break (it will make a loud bang when it does),
unplug the power cord from the outlet, and make sure to request a
replacement lamp from your local dealer. Note that shards of glass
could damage the projector’s internals, or cause injury during handling,
so please do not try to clean the projector or replace the lamp yourself.
•
If the lamp should break (it will make a loud bang when it does), ventilate the
Disconnect
the plug
from the
power
room well, and make sure not to inhale the gas or fine particles that come out
from the projector's vent holes, and not to get them into your eyes or mouth.
• Before replacing the lamp, turn the projector off and unplug the power
cord, then wait at least 45 minutes for the lamp to cool sufficiently.
Handling the lamp while hot can cause burns, as well as damaging the lamp.
outlet
• Never unscrew except the appointed (marked by an arrow) screws.
• Do not open the lamp cover while the projector is suspended from
a ceiling. This is dangerous, since if the lamp’s bulb has broken, the
shards will fall out when the cover is opened. In addition, working in
high places is dangerous, so ask your local dealer to have the lamp
replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp
replacing, make sure that the screws are screwed in firmly. Loose
screws could result in damage or injury.
•
Use only the lamp of the specified type. Use of a lamp that does not meet the lamp
specifications for this model could cause a fire, damage or shorten the life of this product.
• If the lamp breaks soon after the first time it is used, it is possible
that there are electrical problems elsewhere besides the lamp. If this
happens, consult your local dealer or a service representative.
•
Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• Using the lamp for long periods of time, could cause it dark, not to light
up or to burst. When the pictures appear dark, or when the color tone is
poor, please replace the lamp as soon as possible. Do not use old (used)
lamps; this is a cause of breakage.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning and replacing the air filter
The air filter unit of this projector consists of a filter cover, two kinds of filters, and
a filter frame. The new double large filters system is expected to function longer.
However, please check and clean it periodically to keep ventilation needed for
normal operation of the projector.
When the indicators or a message prompts you to clean the air filter, comply with
it as soon as possible. Replace the filters when they are damaged or too soiled.
To prepare new filters, make contact with your dealer and tell the following type
number.
Type number : UX36761 (Filter set)
When you replace the lamp, please replace the air filter. An air filter of specified
type will come together with a replacement lamp for this projector.
Turn the projector off, and unplug the power cord.
Allow the projector to sufficiently cool down.
2
1.
2. Use a vacuum cleaner on and around the filter cover.
3. Pick and pull up the filter cover knobs to take it off.
Filter cover
3
4
Use a vacuum cleaner for the filter vent of the
projector.
4.
Take the fine meshed filter out while holding the
filter cover. It is recommended to leave the coarse
meshed filter in the filter cover as it is.
5.
Filter cover knobs
Intake vent
Use a vacuum cleaner on both sides of the fine
meshed filter while holding it so it will not be
sucked in. Use a vacuum cleaner for the inside of
the filter cover to clean up the coarse meshed filter.
If the filters are damaged or heavily soiled, replace
them with new ones.
6.
7
Put the fine meshed filter on the coarse meshed
one, turning its stitched side up.
7.
Filter (coarse meshed)
Filter (fine meshed)
8. Put the filter unit back into the projector.
Stitched
side
(continued on next page)
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Cleaning and replacing the air filter (continued)
Turn the projector on and reset the filter time using the FILTER TIME item in
the EASY MENU.
(1) Press the MENU button to display a menu.
(2) Point at the FILTER TIME using the ▼/▲ button, then press the ► button.
A dialog will appear.
9.
(3) Press the ► button to select “OK” on the dialog. It performs resetting the
filter time.
WARNING ►Before taking care of the air filter, make sure the power cable
is not plugged in, then allow the projector to cool sufficiently. Taking care of the
air filter in a high temperature state of the projector could cause an electric shock,
a burn or malfunction to the projector.
►Use only the air filter of the specified type. Do not use the projector without the
air filter or the filter cover. It could result in a fire or malfunction to the projector.
►Clean the air filter periodically. If the air filter becomes clogged by dust or the
like, internal temperatures rise and could cause a fire, a burn or malfunction to
the projector.
NOTE • Please replace the air filter when it is damaged or too soiled.
• When you replace the projection lamp, please replace the air filter. An air filter
of specified type will come together with a replacement lamp for this projector.
• Please reset the filter time only when you have cleaned or replaced the air
filter, for a suitable indication about the air filter.
• The projector may display the message such as “CHECK THE AIR FLOW” or
turn off the projector, to prevent the internal heat level rising.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Other care
Inside of the projector
In order to ensure the safe use of your projector, please have it cleaned and
inspected by your dealer about once every year.
Caring for the lens
If the lens is flawed, soiled or fogged, it could cause deterioration of display
quality. Please take care of the lens, being cautious of handling.
Turn the projector off, and unplug the power cord. Allow the projector to cool
sufficiently.
1.
After making sure that the projector is cool adequately, lightly wipe the lens
with a commercially available lens-cleaning wipe. Do not touch the lens
directly with your hand.
2.
Caring for the cabinet and remote control
Incorrect care could have adverse influence such as discoloration, peeling paint,
etc.
Turn the projector off, and unplug the power cord. Allow the projector to cool
sufficiently.
1.
After making sure that the projector is cool adequately, lightly wipe with gauze
or a soft cloth.
If the projector is extremely dirty, dip soft cloth in water or a neutral cleaner
diluted in water, and wipe lightly after wringing well. Then, wipe lightly with a
soft, dry cloth.
2.
WARNING ►Before caring, make sure the power cord is not plugged in,
and then allow the projector to cool sufficiently. The care in a high temperature
state of the projector could cause a burn and/or malfunction to the projector.
►Never try to care for the inside of the projector personally. Doing is so
dangerous.
►Avoid wetting the projector or inserting liquids in the projector. It could result in
a fire, an electric shock, and/or malfunction to the projector.
• Do not put anything containing water, cleaners or chemicals near the projector.
• Do not use aerosols or sprays.
CAUTION ►Please take right care of the projector according to the
following. Incorrect care could cause not only an injury but adverse influence
such as discoloration, peeling paint, etc.
►Do not use cleaners or chemicals other than those specified in this manual.
►Do not polish or wipe with hard objects.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
If an abnormal operation should occur, stop using the projector immediately.
WARNING ►Never use the projector if abnormal operations such as smoke,
strange odor, excessive sound, damaged casing or elements or cables, penetration
of liquids or foreign matter, etc. should occur. In such cases, immediately disconnect
the power plug from the power outlet. After making sure that the smoke or odor has
stopped, contact to your dealer or service company.
Otherwise if a problem occurs with the projector, the following checks and measures are
recommended before requesting repair.
If this does not resolve the problem, please contact your dealer or service company. They
will tell you what warranty condition is applied.
Related messages
When some message appears, check and cope with it according to the following table.
Although these messages will be automatically disappeared around several minutes, it will
be reappeared every time the power is turned on.
Message
Description
There is no input signal.
Please confirm the signal input connection, and the status
of the signal source.
The horizontal or vertical frequency of the input signal is
not within the specified range.
Please confirm the specs for your projector or the signal
source specs.
An improper signal is input.
Please confirm the specs for your projector or the signal
source specs.
The internal temperature is rising.
Please turn the power off, and allow the projector to cool
down at least 20 minutes. After having confirmed the
following items, please turn the power ON again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the remedy, please set
FAN SPEED of the SERVICE item in the OPTION menu to HIGH.
A note of precaution when cleaning the air filter.
Please immediately turn the power off, and clean or change
the air filter referring to the “Cleaning and replacing the
air filter” section of this manual. After you have cleaned or
changed the air filter, please be sure to reset the filter timer
(
47).
The button operation is not available ( 6).
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Regarding the indicator lamps
When operation of the LAMP, TEMP and POWER indicators differs from usual,
check and cope with it according to the following table.
POWER
indicator indicator indicator
LAMP
TEMP
Description
Lighting
In Orange
Turned
off
Turned
off
The projector is in a standby state.
Please refer to the section “Power on/off”.
Blinking
In Green
Turned
off
Turned
off
The projector is warming up.
Please wait.
Lighting
In Green
Turned
off
Turned
off
The projector is in an on state.
Ordinary operations may be performed.
Blinking
In Orange
Turned
off
Turned
off
The projector is cooling down.
Please wait.
The projector is cooling down. A certain error
has been detected.
Please wait until POWER indicator finishes blinking,
and then perform the proper measure using the item
descriptions below.
Blinking
In Red
(discre- (discre-
tionary) tionary)
The lamp does not light, and there is a possibility
that interior portion has become heated.
Please turn the power off, and allow the projector to
cool down at least 20 minutes. After the projector has
sufficiently cooled down, please make confirmation of
the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
Blinking
In Red
or
Lighting
In Red
Lighting Turned
In Red
off
•
Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the remedy, please
change the lamp referring to the section “Replacing the lamp”.
The lamp cover has not been properly fixed.
Please turn the power off, and allow the projector to
cool down at least 45 minutes. After the projector has
Blinking
In Red
or
Lighting
In Red
Blinking Turned sufficiently cooled down, please make confirmation of
In Red
off
the attachment state of the lamp cover. After performing
any needed maintenance, turn the power on again.
If the same indication is displayed after the remedy,
please contact your dealer or service company.
The cooling fan is not operating.
Please turn the power off, and allow the projector to
cool down at least 20 minutes. After the projector has
Turned Blinking sufficiently cooled down, please make confirmation
Blinking
In Red
or
Lighting
In Red
off
In Red that no foreign matter has become caught in the fan,
etc., and then turn the power on again.
If the same indication is displayed after the remedy,
please contact your dealer or service company.
(Continued on next page)
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Regarding the indicator lamps (continued)
POWER
indicator indicator indicator
LAMP
TEMP
Description
There is a possibility that the interior portion
has become heated.
Please turn the power off, and allow the projector to cool down at least
20 minutes. After the projector has sufficiently cooled down, please make
confirmation of the following items, and then turn the power on again.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
If the same indication is displayed after the remedy, please set FAN
Blinking
In Red
or
Lighting
Turned Lighting
off
In Red
In Red
SPEED of SERVICE item in OPTION menu to HIGH
.
49)
(
It is time to clean the air filter.
Please immediately turn the power off, and clean or
change the air filter referring to the section “Cleaning
and replacing the air filter”. After cleaning or changing
the air filter, please be sure to reset the filter timer.
After the remedy, reset the power to ON.
Lighting
In Green
Simultaneous
blinking in Red
There is a possibility that the interior portion
has become overcooled.
Please use the unit within the usage temperature
parameters (5°C to 35°C).
Lighting
In Green
Alternative
blinking in Red
After the treatment, reset the power to ON.
NOTE
•
When the interior portion has become overheated, for safety
purposes, the projector is automatically shut down, and the indicator lamps
may also be turned off. In such a case, disconnect the power cord, and wait at
least 45 minutes. After the projector has sufficiently cooled down, please make
confirmation of the attachment state of the lamp and lamp cover, and then turn
the power on again.
Resetting all settings
When it is hard to correct some wrong settings, the FACTORY RESET function of
SERVICE item in OPTION menu (50) can reset all settings(except LANGUAGE,
FILTER TIME, LAMP TIME, FILTER MESSAGE and SECURITY settings and etc.)
to the factory default.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects
About the phenomenon confused with a machine defect, check and cope with it
according to the following table.
Reference
page
Phenomenon
Cases not involving a machine defect
The electrical power cord is not plugged in.
Correctly connect the power cord.
11
The main power source has been interrupted during
operation such as by a power outage (blackout), etc.
Please disconnect the power plug from the power outlet,
and allow the projector to cool down at least 10 minutes,
then turn the power on again.
11, 13
57, 58
Power does not
come on.
Either there is no lamp and/or lamp cover, or either
of these has not been properly fixed.
Please turn the power off and disconnect the power plug from
the power outlet, and allow the projector to cool down at least
45 minutes. After the projector has sufficiently cooled down,
please make confirmation of the attachment state of the lamp
and lamp cover, and then turn the power on again.
The signal cables are not correctly connected.
Correctly connect the connection cables.
9
–
Signal source does not correctly work.
Correctly set up the signal source device by referring to the
manual of the source device.
Neither sounds
nor pictures are
outputted.
The input changeover settings are mismatched.
Select the input signal, and correct the settings.
15, 16
The BLANK function for pictures and the MUTE
function for sounds are working.
AV MUTE may be active.
15, 22,
48
Refer to the item “Sound does not come out” and “No
pictures are displayed” on the next page to turn off the
MUTE and BLANK functions.
(Continued on next page)
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects (continued)
Reference
page
Phenomenon
Cases not involving a machine defect
The signal cables are not correctly connected.
Correctly connect the audio cables.
9
The MUTE function is working.
Restore the sound pressing the MUTE or VOLUME +/-
button on the remote control.
15
15
39
39
The volume is adjusted to an extremely low level.
Adjust the volume to a higher level using the menu function
or the remote control.
Sound does not
come out.
The AUDIO SOURCE/SPEAKER setting is not correct.
Correctly set the AUDIO SOURCE/SPEAKER in the AUDIO
menu.
The mode selected for HDMI AUDIO is not suitable.
Check each of the two modes provided and select the
suitable one for your HDMI audio device.
The lens cover is attached.
Remove the lens cover.
14
9
The signal cables are not correctly connected.
Correctly connect the connection cables.
The brightness is adjusted to an extremely low level.
Adjust the BRIGHTNESS to a higher level using the menu
function.
27
10
No pictures are
displayed.
The computer cannot detect the projector as a plug
and play monitor.
Make sure that the computer can detect a plug and play
monitor using another plug and play monitor.
The BLANK screen is displayed.
Press the BLANK button on the control panel or the remote
control.
22
22
The FREEZE function is working.
Press the FREEZE button to restore the screen to normal.
Video screen
display freezes.
Color settings are not correctly adjusted.
Perform picture adjustments by changing the COLOR
TEMP, COLOR, TINT and/or COLOR SPACE settings,
using the menu functions.
Colors have a
faded- out
appearance, or
Color tone is
poor.
28, 33
The COLOR SPACE setting is not suitable.
Change the COLOR SPACE setting to the AUTO, RGB,
SMPTE240, REC709 or REC601.
33
(Continued on next page)
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects (continued)
Reference
page
Phenomenon
Cases not involving a machine defect
The brightness and/or contrast are adjusted to an
extremely low level.
Adjust the BRIGHTNESS and/or CONTRAST settings to a
higher level using the menu function.
27
The ECO MODE function is working.
Select the NORMAL for the ECO MODE item in the SETUP
menu.
Pictures appear
dark.
38
The lamp is approaching the end of its product
lifetime.
57, 58
Replace the lamp.
Either the focus and/or horizontal phase settings are
not properly adjusted.
Adjust the focus using the focus ring, and/or the H PHASE
using the menu function.
18, 32
Pictures appear
blurry.
The lens is dirty or misty.
Clean the lens referring to the section “Caring for the lens”.
61
No signal is
output from the
MONITOR OUT
and AUDIO
The SAVING function is working in the standby state.
Select the NORMAL for the STANDBY MODE item in the
SETUP menu.
38
OUT ports.
RS-232C does
not work.
When the projector is operating in Eco mode,
flickering may appear on screen.
Set ECO MODE to NORMAL, and set AUTO ECO MODE to
OFF, in the SETUP menu.
37, 38
Some kind
of image
degradation
such as
The OVER SCAN ratio is too big.
Adjust OVER SCAN in the IMAGE menu smaller.
30
33
flickering or
stripes appear
on the screen.
Excessive VIDEO NR.
Change the setting of VIDEO NR in the INPUT menu.
The FRAME LOCK function cannot work on the
current input signal.
35
Set FRAME LOCK in the INPUT menu to OFF.
(Continued on next page)
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Phenomena that may be easy to be mistaken for machine defects (continued)
NOTE • Although bright spots or dark spots may appear on the screen, this
is a unique characteristic of liquid crystal displays, and it does not constitute or
imply a machine defect.
• The projector may make a rattling sound when tilted, moved or shaken, since
a flap to control the air flow inside of the projector has moved. Be aware that
this is not a failure or malfunction.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications
Specifications
Item
Product name
Liquid Crystal Panel
Lamp
Specification
Liquid crystal projector
1,024,000 pixels (1280 horizontal x 800 vertical)
200 W UHB
Speaker
1 W
Power supply
Power consumption
Temperature range
AC 100-120 V/2.9 A, AC 220-240 V/1.4 A
AC 100-120 V/290 W, AC 220-240 V/270 W
5 ~ 35 °C (Operating)
306 (W) x 77 (H) x 221 (D) mm
* Not including protruding parts. Please refer to the following figure.
Size
Weight (mass)
approx. 2.2 kg
Computer input port
COMPUTER IN ..................................D-sub 15 pin mini x1
Computer output port
MONITOR OUT ..................................D-sub 15 pin mini x1
HDMI input port
HDMI ....................................................HDMI connector x1
Video input port
S-VIDEO...................................................mini DIN 4 pin x1
VIDEO ..................................................................... RCA x1
Audio input/output port
Ports
AUDIO IN1.....................................................Stereo mini x1
AUDIO IN2.....................................................Stereo mini x1
AUDIO OUT ..................................................Stereo mini x1
Others
CONTROL.................................................... D-sub 9 pin x1
Lamp: 456-8789H
Filter set: UX36761
Laser remote control: RC-R008
Optional parts
* For more information, please consult your dealer.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications (continued)
306
[unit: mm]
403-8791HW-GENERAL-00
Download from Www.Somanuals.com. All Manuals Search And Download.
70
|