1999 Operator's Manual
4500
SERIES
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
SAFETY .................................................................Pages 2 - 7
WARRANTYPOLICY..............................................Page
SPECIFICATIONS..................................................Page
SEAT ADJUSTMENT.............................................Page
8
9
10
CONTROLS ...........................................................Pages 11 - 14
OPERATIONINSTRUCTIONS ................................Pages 15 - 20
CARE AND MAINTENANCE..................................Pages 21 - 31
STANDARD PARTS LIST ......................................Page
32
TROUBLESHOOTING ............................................Pages 33 - 35
4500 Series
Part No. 5863-0798
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
RIDINGLAWNMOWERS,IFIMPROPERLYOPERATED,
CANCAUSESERIOUSINJURYORDEATH
The most common causes of injury to the operator or bystander...
BLADECONTACT
TIP-OVER
BACK-OVER
...read and understand this manual to prevent injuries.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SAFETY SYMBOLS
Safety Alert Symbol
When you see this symbol,
BE ALERT to the potential for injury.
Follow recommended safety precautions and safe
operating practices.
Danger
indicates an imminently hazardous situation
which, if not avoided, will result in death or
serious injury.
Warning
indicates a potentially hazardous situation
which, if not avoided, could result in death or
serious injury.
Caution
indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury. It may also be used to alert
againstunsafepractices.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
This cutting mower is capable of amputating hands & feet,
and throwing objects.
Failure to observe the following safety instructions could result in
serious injury or death.
GENERAL OPERATION:
• Read, understand, and follow all instructions in the manual and on the mower before
starting.
• Only allow responsible adults, who are familiar with the instructions, to operate the
mower.
• Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and
thrown by the blade.
• Be sure the area is clear of other people before mowing. Stop mower if anyone enters
the area.
• Nevercarrypassengers.
• Do not mow in reverse unless absolutely necessary. Always look down and behind
before and while backing.
• Be aware of the mower discharge direction and do not point it at anyone. Do not
operate the mower without either the entire grass catcher or the deflector in place.
• Slow down before turning.
• Never leave a running mower unattended. Always turn off blades, set parking brake,
stop engine, and remove key before dismounting.
• Turn off blades when not mowing.
• Stop engine before removing grass catcher or unclogging chute.
• Mow only in daylight or good artificial light.
• Do not operate the mower while under the influence of alcohol or drugs.
• Watch for traffic when operating near or crossing roadways.
• Use extra care when loading or unloading the mower into a trailer or truck.
Do not ride the mower when loading & unloading.
The Engine Exhaust from this product contains chemicals known to the
State of California to cause cancer, birth defects or other reproductive harm.
WARNING:
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SLOPE OPERATION:
Slopes are a major factor related to loss-of-control and tip-over accidents,
which can result in severe injury or death.
All slopes require extra caution.
If you cannot back up the slope or if you feel uneasy on it, do not mow it.
DO
Mow across the slope with your Dixon ZTR - never up or down.
Remove obstacles such as rocks, tree limbs, etc.
Watch for holes, ruts or bumps. Uneven terrain could overturn the mower. Tall grass can hide
obstacles.
Use slow speed.
Use extra care with grass catchers or other attachments. These can change the stability of the
mower.
Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or
direction.
Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed
slowly down the slope.
If front wheels lift off the ground, pull the levers back to stabilize the mower.
DO NOT
Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.
Do not mow near drop-offs, ditches, or embankments. The mower could suddenly turn over if
a wheel is over the edge of a cliff or ditch, or if an edge caves in.
Do not mow on wet grass. Reduced traction could cause sliding.
Do not try to stabilize the mower by putting your foot on the ground.
Do not use grass catcher on steep slopes.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
CHILDREN:
Tragic accidents can occur if the operator is not alert to the
presence of children.
Children are attracted to lawn mowers and the mowing activity.
NEVER assume children will stay where they were last seen.
Be alert to avoid accidents.
• Keep children out of the mowing area and under the watchful care of another
responsible adult.
• Be alert and turn mower off if a child enters the area.
• Before and during backing, look behind and DOWN for small children.
• Never carry children. They may fall off and be seriously injured or interfere with safe
mower operation.
• Never allow children to operate the mower.
• Use extra care when approaching blind corners, shrubs, trees, or other objects that may
obscure vision.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SERVICE:
•
Use extra care in handling gasoline and other fuels. They are flammable and vapors
are explosive.
Use only an approved container.
Never remove gas cap or add fuel with the engine running. Allow engine to cool
before refueling. Do not smoke.
Never refuel the mower indoors.
Never store the mower or fuel container inside a building where there is an open
flame.
•
Never run a mower inside a closed area. The exhaust fumes are toxic.
•
Keep nuts and bolts tight, especially blade attachment bolts, and keep equipment in
good condition.
•
•
Never tamper with safety devices. Check their proper operation regularly.
Keep mower free of grass, leaves, or other debris buildup. Clean up oil or fuel
spillage. Allow mower to cool before storing.
•
Stop and inspect the equipment if you strike an object. Repair, if necessary, before
restarting.
•
•
Never make adjustments or repairs with the engine running.
Grass catcher components are subject to wear, damage, and deterioration, which
could expose moving parts or allow objects to be thrown. Frequently check
components and replace with original equipment parts, when necessary.
•
•
Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra
caution when servicing them.
Batteries contain sulfuric acid. To prevent burns avoid contact with skin, eyes and
clothing. To prevent a fire or explosion keep sparks and open flames away from
battery.
Before disconnecting the negative (-) ground cable, make sure all switches are OFF.
•
Check to assure that the drive chains are properly adjusted. A loose chain may come
off causing loss of control.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
DIXON PROTECTION PLUS TWO YEAR LIMITED WARRANTY POLICY
This warranty policy applies to all ZTR 4500 Series mowers purchased on or after September 1, 1997.
WARRANTY: The Dixon ProtectionPlusWarrantytermisforaperiodoftwo(2)years fromdateofpurchase. DIXON
ZTRMOWERSAREWARRANTEDAGAINSTDEFECTSINMATERIALSANDWORKMANSHIPANDPROVIDESFOR
REPLACEMENTORREPAIROFPARTSINCLUDINGLABORCOSTS.THISWARRANTYISSUBJECTTOTHE
FOLLOWINGCONDITIONSANDLIMITATIONS:
1.
2.
Warranty applies only to original retail purchaser of new and unused mowers and accessories.
AllDixonwarrantymustbeaccomplishedbyauthorizedDixondealersandinaccordancewithDixon
warranty policy and allowances. All warranty claims must be approved by Dixon Industries, Inc.
3.
Mowers or accessories used for commercial applications are warranted for 90 days from date of
purchase. Commercial application is any use other than, or in addition to, mowing at owner's primary
placeofresidence.
4.
5.
Battery warranty: Limited to 90 days from date of purchase.
Accessories Warranty (Grass Catchers, Snow Blades, Covers, etc.): Limited to 90 days from date of
purchase.
6.
7.
Warranty does not apply to damage in transit or incidents of misuse, negligence, accidents, or
alteration. The use of parts or components other than those supplied by Dixon Industries, Inc.
VOIDSALLWARRANTY.
The following items are not covered by this warranty policy:
(a) Pick up and delivery charges for transportation of mower to and from an Authorized Dixon Dealer's
place of business.
(b) Routinemaintenanceoradjustments.
(c) Belts / chains / sprockets / cutting blades.
(d) Engines -- All engines used on Dixon ZTR mowers are warranted by each individual engine
manufacturer.
(e) Any costs or expense of providing substitute equipment while repair work is being performed on a
warranted mower.
8.
There is no other express warranty. Implied warranties, including those of merchantability and fitness
for a particular purpose, are limited to the same duration of the express warranty, and to the extent
permitted by law any and all implied warranties are excluded. Liabilities for consequential damages
under any and all warranties are excluded.
WARRANTYVALIDATION:Atthetimeofsale,sellingdealermustrevieweachportionofthiswarrantydocument,completethe
informationsectionbelow,securecustomer'ssignatureandsendcopytoDixonIndustries,Inc.
DM-
DATEOFPURCHASE_______________________________Model____________________ S/N______________________
(Owner'sName)
(Address)
(Dealership)
(Address)
(Owner'sSignature)
Page 10
(Dealer'sSignature)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Models ZTR 4515B and 4516K
CHASSIS:
BODY:
Twin 12 gauge side frames and 7 gauge transmission and engine base plate.
All body parts are made of high density polyethylene. Dent and corrosion
resistant. Front body contains access panel for battery service.
MOWER DECKS:
36" Deck: 11 GA Laser Cut Fabricated - 36" Cut Width
42" Deck: 13 GA Stamped Steel Construction - 42" Cut Width
50" Deck 11 GA Fabricated Construction/Reinforcement Ribs - 50" Cut Width
Cut height approximately 1" to 4" via 7 position lift handle.
Electric clutch.
BLADEDRIVE:
TRANSMISSION:
ENGINE:
Each rear wheel is independently driven by a HydroGear IZT hydrostatic drive.
Model 4515B:
15HP Vanguard Briggs & Stratton, 4-Cycle, Single Cylinder, Overhead
Valve, Air-Cooled, Gasoline, Vertical Shaft With Cast Iron Cylinder
Sleeve, Oil Pump With Integral Oil Filter.
Model 4516K:
16 HP Kohler Command 16, 4-Cycle, Single Cylinder, Overhead Valve,
Air-Cooled, Gasoline, Pressure Lubricated, With Oil Filter, Vertical Shaft,
Aluminum Head and Block with Cast-Iron Cylinder Liner. Smart Spark
Ignition.
STARTING SYSTEM:
TIRES:
Electric by key switch operation with safety interlock blade drive.
Front
Rear
11 X 4.00 X 5 ribbed tread.
18 X 8.50 X 8 Multi-Trac
RECOMMENDED
TIRE PRESSURE:
Front
Rear
16-21 lbs.
8-14 lbs.
CAPACITIES:
DIMENSIONS:
Fuel
Engine
2.7 gallons total.
Briggs & Stratton - 1.50 quarts oil.
Kohler - 2 quarts oil with filter.
Width
44" Maximum Track Width
42" to top edge of seat.
72" hitch tab to front bumper.
Height
Length
Weight
Power Unit:
w/36" Deck:
w/42" Deck:
463 lbs.
544 lbs.
541 lbs.
NOTE:
Additionalinformationprovidedinserviceinstructionsundertheindividualcomponent.
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
SEAT ADJUSTMENT INSTRUCTIONS
1.
2.
3.
Place parking brake in ON position. (Pull brake lever up)
Raise and push seat assembly forward.
Loosen five nuts, P/N 3205, and slide seat forward or backward to desired position.
Retighten nuts, P/N 3205.
DO NOT operate mower without seat adjustments properly tightened.
4
Raise and push seat assembly and upper body rearward to closed position.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
CONTROL
LEVERS
FRONT OF
MACHINE
IGNITION
SWITCH
THROTTLE
CONTROL
BLADE
DRIVE
SWITCH
DECK HEIGHT
ADJUSTMENT
LEVER
CIRCUIT
BREAKER
LIGHT
SWITCH
PARKING
BRAKE
LEVER
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
PARKING BRAKE:
The parking brake is designed to hold the mower from moving
and is not intended for use in stopping the mower while it is
in motion. The engine will stop if the parking brake is engaged
while the control levers are in the drive position.
CAUTION
Engage parking brake before
starting engine.
TO SET PARKING BRAKE:
The hand operated parking brake is located on the right
fender.
To engage brake, pull lever up(to the rear).
To release brake, move lever forward (down).
NOTE: Always set parking brake before dismounting.
Release parking brake before moving mower.
TRANSMISSION DRIVE SYSTEM:
Allows the mower to turn on its own axis
"Zero Turning Radius"
Each lever controls one side of the mower.
NOTE: The pressure required to operate the mower is very
light.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS:
(left turn opposite)
TO GO FORWARD:
From neutral position, gently push both drive levers forward.
To increase speed, move levers farther forward.
TO GO BACKWARD:
From neutral position, gently pull both drive levers toward you.
TURNING:
Turning is controlled by moving one drive lever slightly forward or rearward of the other.
To turn left, move left lever rearward of the right lever.
To turn "square corners" move lever of desired direction to neutral.
To turn on mower's own axis (zero turning radius) stop and move one lever to reverse
position and the other to forward position.
BRAKING:
To brake mower, move both levers in direction opposite of travel, release levers to
neutral, set parking brake. Park only on level surfaces.
THROTTLE CONTROL:
Located on control panel to operator's right.
Throttle control for engine speed.
Choke for engine starting.
Throttle Control should be set to the MAXIMUM or wide open setting to insure adequate
cooling of the engine and to maintain mower deck blade speed while mowing.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS:
BLADE DRIVE:
Located on control panel, on operator's right.
To engage the mower blades, pull up on the
switch.
To disengage blades, push down.
CIRCUITBREAKER:
Protection of the electrical system is by
(1) 15 amp circuit breaker.
If circuit breaker trips, push button to reset.
If this condition repeats, consult dealer
for inspection and repair.
MOWER DECK CUT HEIGHT LIFT LEVER:
Located to the left of operator.
Controlsthecuttingheight.
Sevenpositionsofadjustment.
Move lever in and forward to lower.
Move lever in and back to raise.
NOTE: Always use high for transport.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONINSTRUCTIONS
Safeandsuccessfuloperationwilldependupontheoperatorhavingthecorrect knowledgeofall
controls used on the mower and making good judgements about the terrain to be mowed.
NEVER allow anyone to operate the mower without complete knowledge of all controls and
their functions.
During initial operation, "learning to drive", set throttle at slow speed.
Soundjudgementbytheoperatorwillpreventaccidents.
Drink/Cup Holder located on the left rear fender is for transport or carrying only!
Mower usage requires that both hands be free to control individual levers.
DO NOT ATTEMPT operation of mower with any type
of container or other object in either hand.
Towing
Towing a trailer or other attachment that is too heavy could damage the drive or cause the
mower to become unstable. Limit loads to 250 pounds or less on this mower.
BEFORE OPERATING MOWER:
1. Read engine manufacturer's operating and maintenance
instructions.
2. Read and observe all safety instructions on your mower and in
the manual.
3. Check engine oil.
4. Be sure gas cap is in place.
5. Be sure parking brake is on.
6. Be sure mower blade drive is off.
7. Know how to stop engine. (Turn key to off position)
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONINSTRUCTIONS
TESTING OF SAFETY INTERLOCK
SYSTEMS:
PARKING BRAKE SWITCH TEST: a) Swing out control levers
b) Disengage blade drive switch
c) Put Parking brake in OFF position
d) Turn ignition switch to START
Engine should not turn over or attempt to start.
CONTROL LEVER SWITCH TEST: a) Disengage blade drive switch
b) Put parking brake in ON position
c) Swing control levers in
d) Turn ignition switch to START
Engine should not turn over or attempt to start.
a) Put parking brake in ON position
b) Swing out control levers
c) Engage blade drive switch
BLADE DRIVE SWITCH TEST:
SEAT SWITCH TEST:
d) Turn ignition switch to START
Engine should not turn over or attempt to start.
a) In a SAFE AREA away from bystanders,
start the engine
b) Leave levers swung out and parking brake ON
c) Engage blade drive
d) Raise slightly off seat
ENGINE SHOULD STOP
e) Disengage blade drive
f) with engine running, put parking brake
in OFF position
g) Swing levers in
h) Engage blade drive
i) Raise weight slightly off seat.
ENGINE SHOULD STOP
NOTE:
If Any Safety Check FAILS, Do Not Operate The Mower until the system has
been checked and repaired by an Authorized Dixon ZTR Dealer
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONINSTRUCTIONS
Engage parking brake before starting engine.
CAUTION
STARTING INSTRUCTIONS:
1. Parking brake must be on, control levers swung out, and
blade drive disengaged.
2. Move throttle control to "Choke" position if engine is cold,
full throttle if warm.
3. Insert ignition key and turn to "Start" position. When
engine starts, release ignition key. Key will return to
"Run" position.
4. Move throttle from "Choke" to desired speed position.
5. Release parking brake.
6. Swing levers in.
7. Operate the mower per the "CONTROL" instructions
on page 12.
NOTE: While mowing throttle control must be set to the
MAXIMUM or wide open setting to insure adequate
cooling of the engine and to maintain mower deck
blade speed.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONINSTRUCTIONS
MOWING WITH A MULCHING ATTACHMENT:
Mulching or recycling the grass clippings requires a totally different mowing approach than would be
normal when side discharging or bagging the grass. There may be instances or conditions where it is
not possible to hide all of the recycled or mulched clippings.
In order to achieve the best results, please read and follow the mulching tips listed below:
1.
2.
Set the engine speed control to the wide open or full setting.
Place the mower deck cut height selector in either the top or second notch. Never cut more
than 3/4" to 1" off the grass at any one time. Attempting to cut more grass will result in the
deck plugging and cause the engine to stall.
3.
4.
5.
6.
7.
It may be necessary to cut the lawn twice to achieve acceptable mulching performance
especially on first cuttings or if the lawn is heavily fertilized.
Do Not Attempt To Cut Grass When It Is Wet. Mulching performance will be very poor under
wet grass conditions.
Maintain A Sharp Blade Throughout The Cutting Season. This is very important. Optimal
mulching performance cannot be obtained with a dull or nicked up blade.
Keep The Underside Of The Mower Deck Clean. Remove all grass and dirt buildup from the
underside of the pan, the baffles and deflectors after each use.
Alternate mower direction. This will evenly disperse the mulched grass clippings over the
lawn for even fertilization.
If the mulching quality of the mower does not seem to be satisfactory, try one or more of the
following tips:
1.
2.
3.
4.
5.
6.
Raise the height-of-cut setting on your mower.
It may be necessary to cut your grass more frequently.
Operate the mower at a slower ground speed.
Overlap cutting swaths instead of cutting a full swath with each pass.
Mow across the marginal areas a second time.
CUT HIGH - MOW OFTEN!
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONINSTRUCTIONS
MOWING WITH A GRASS CATCHER ATTACHMENT:
In order to achieve optimum performance when mowing with a grass catching attachment, please read
and follow the tips listed below.
1.
Some applications may require installation of an "Optional" weight box on the front of the mower
to offset cut grass weight.
2.
3.
Set engine speed control to the wide open or full setting.
Do Not Attempt To Cut Grass When It Is Wet. Wet grass will clog both the underside of the deck
and the attachment chutes. Empty bags often to prevent plugging.
4.
5.
6.
7.
If the grass is tall, place the mower deck cut height selector in the top or second notch. Initially
overlap cutting swaths instead of a full swath with each pass.
Keep The Underside Of The Mower Deck Clean. Frequent removal of dried grass and dirt will
greatly assist in bagging of the clippings.
Maintain Sharp Blades Throughout The Cutting Season. Some grass catching attachments
require "Hi-Lift" blades.
Operate the mower at a slower ground speed than when mowing without a grass catching
attachment.
CAUTION
•
•
•
Watch for low hanging branches or other obstacles which might hit the catcher top while turning
or backing the mower.
Use care when backing to avoid pushing the grass bags into the frame or "hot" exhaust muffler
of the engine.
Disengage blade and stop engine prior to clearing grass from either the discharge chute or grass
catcher components.
•
•
Keep all attachment bolts tight.
Do Not operate the mower with the grass catching attachment partially removed.
•
Important:
• Do not leave clippings in the bags while the mower is stored.
• Damp grass clippings are a fire hazard if left in the bags.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONINSTRUCTIONS
SIDE DISCHARGE OF THE CLIPPINGS:
In order to achieve optimum performance when side discharging the grass clippings, please read
and follow the tips listed below.
Additional information can be found in the troubleshooting guide.
CAUTION Be sure that deflector is properly installed
on the discharge chute.
1. Set engine speed control to the wide open or full setting.
2. Do Not Attempt To Cut Grass When It Is Wet. Wet grass will clog the underside of the deck
and discharge area.
3. If the grass is tall, place the mower deck cut height lever in the top or second notch. Initially
overlap cutting swaths instead of a full swath with each pass. Some applications may require a
second cutting.
4. Keep The Underside Of The Mower Deck Clean. Frequent removal of dried grass and dirt will
allow the clippings to discharge correctly.
5. Maintain Sharp Blades Throughout The Cutting Season.
GRASS HEIGHT SUGGESTIONS:
Correct mowing height can reduce weeds and disease by 50 to 80%
The following grass cut heights are based on adequate moisture conditions and normal thatch
buildup in a healthy lawn. Some locations and applications may require slightly different cut
heights. If in doubt, consult your local lawn professional for assistance.
Grass Types:
Best Cut Heights
Zoysia
Blue Grass
Fescue Blends
St. Augustine (Mid South)
St. Augustine (Deep South)
Tifton Bermuda
2" - 2 1/2"
1 1/2" - 3"
1 1/2" - 3"
1 1/2" - 2"
3" - 4"
1 1/2"
Centipede
Common Bermuda
Bahia/Argentina/Pensacola
1 1/2" - 2"
1 1/2" - 2"
2"
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
Thisportionoftheownersmanualdealswithnormalserviceitemswhichcanbeperformedbytheowner.
Please remember that if you are in doubt as to the correct service procedures to be followed, these and
other service situations can be handled by a Dixon ZTR dealer who is familiar with the service of your
mower.
MAINTENANCE SCHEDULE:
To insure a long and trouble free service life of all components, a regular and thorough
maintenance schedule should be followed. The following items should be checked after
the first (10) hours of operation and on a weekly basis, or each (40) hours of use:
1.
2.
3.
4.
5.
6.
Drive system, belts and controls.
Mower deck belts.
Tire pressures.
Tightness of all nuts and bolts.
Battery fluid level.
Engine Oil.
Before performing any maintenance, shut off engine, allow to cool.
CAUTION
ENGINE:
For engine operating and maintenance information, refer to the engine operating and
maintenance instructions furnished by the engine manufacturer, supplied with each
mower.
BATTERY: Check the fluid in the battery at frequent intervals.
Keep fluid level above the plates in each cell, using distilled water.
OFF-SEASON BATTERY STORAGE:
Identify each cable so cables can be reconnected to correct terminals.
Disconnect cables from terminals
ALWAYS disconnect ground cable first and reconnect last
Charge battery.
DO NOT remove battery from mower.
Clean top of battery and terminals with baking soda and water.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
MOWERBLADEMAINTENANCE:
NOTE: Observe proper blade position prior to removal.
1. Safely raise front of mower.
2. Hold or block blade from turning.
3. Loosen blade nut and remove blade.
4. When replacing blade, tighten blade nut securely. Refer to diagram.
Wear heavy, thick gloves when holding onto mower blade,
CAUTION
avoid the sharp edge of the blade.
Note: Be sure blade is center on pilot before tightening nut to 60 ft. lbs. torque.
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
BELT TENSION:
36" DECK:
MOWER DECK DRIVE BELT:
P/N 1300
P/N 6109
Manual adjustment. Refer to illustration below.
42" DECK:
MOWER DECK SERPENTINE BELT:
Manual adjustment. Refer to illustration below.
ENGINE TO MOWER DECK BELT:
P/N 5861
Auto tensioner with spring loaded idler. No adjustment required.
50" DECK:
MOWER DECK SERPENTINE BELT:
P/N 1300
Manual adjustment. Refer to illustration below.
ENGINE TO MOWER DECK BELT:
P/N 7174
Auto tensioner with spring loaded idler. No adjustment required.
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
FORWARD TRAVEL SPEED ADJUSTMENT
1. Drive machine until hydrostats have warmed up.
2. Drive on a smooth, level surface with both levers in top speed position.
3. Ifonesidenowdrivesslightlyfasterthantheother,adjustleverstopwasherP/N5760
on that side to reduce forward range of control lever. If levers are now uneven at top
speed, loosencontrollevermountingnut. Rotatelevertobeevenwithothersideand
tighten nut.
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
NEUTRAL ADJUSTMENT
1. Stop the engine, engage parking brake, and raise rear of frame with jack or blocks so that rear tires
do not contact the ground.
2. Swing out the control levers, start the engine and release the parking brake.
3. Raise the seat to access hydro control linkage. If right wheel creeps, adjust right side linkage, and
vice-versa. Use procedure below:
a. Loosen, but do not remove, the bolt in the control tube P/N 5540.
b. Loosen Jam nuts on ends of the
coupler P/N 7736.
c. Ifrightwheeliscreepingforward,
turn coupler counter clockwise
until neutral is achieved
(clockwise for left side). If right
wheeliscreepingbackward,turn
coupler clockwise until neutral is
achieved (counterclockwise for
left side).
d. Tightenjamnutsagainstcoupler.
e. Tighten bolt in control tube.
4. Lower seat, release parking brake, and swing control levers in. If wheel creeps, repeat steps 3a & 3e.
5. Stop engine and remove rear of machine
from jack or blocks.
6. Drive machine with both levers in top
speed position. If one side now drives
slightly faster than the other, adjust lever
stop washer P/N 5760 on that side to
reduce forward range of control lever. If
levers are now uneven at top speed,
loosencontrollevermountingnut. Rotate
lever to be even with other side and
tighten nut.
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
MOWER DECK LEVELING PROCEDURE:
1. Place mower on a smooth, level surface and check tire pressures to insure correct stance.
Tires should be inflated as follows:
Front: 16 - 21 lbs
Rear: 8 - 14 lbs
2. Turn each outer blade tip to align with the deck in a side to side manner.
3. Measure from the floor surface up to the bottom of the blade tip on the discharge side of the
mower. Retain this measurement. Move to the opposite side and check to see if that
measurement is the same. If adjustment is required, turn nut on one or both of the rear L-rods
until both measurements are equal.
4. Turn each outer blade tip to align with the deck in a front to rear manner.
5. Measure from the floor surface up to the bottom of the blade tips at both the front and rear of
the blades. Rear of blade tips should be to 1/8" to 3/8" higher that the front of blade tips. If
adjustment is necessary, turn nut on front L-rod.
NOTE: This will place the mower deck in a base measurement position. Additional adjustment
may be required to achieve desired cut for the type of grass or conditions involved.
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
36" DECK REMOVAL
1. Place cut height lever in lowest cut position.
2. Loosen nut on belt idler shock mount until belt can be removed from electric
clutch pulley on the bottom of the engine.
3. Remove hair pin cotter and washer from one end of deck support cross shaft.
Note location of remaining shim washers used between chassis and mower deck
plates. Slide shaft from chassis and mower deck.
4. Remove hair pin cotter and washer from each deck L-rod. Remove L-rods from
lift arms. At this point, deck will drop down.
5. Carefully raise and support front of chassis. Slide mower deck to either side for
removal. (Reverse procedure to reinstall deck assembly)
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
42" and 50" DECK REMOVAL:
1. Place cut height lever in lowest cut position.
2. Pull belt idler back to allow belt to be removed from idler pulley and electric clutch
pulley.
3. Remove hair pin cotter and washer from one end of deck support cross shaft.
Note location of remaining shim washers used between chassis and mower deck
plates. Slide shaft from chassis and mower deck.
4. Remove hair pin cotter and washer from each deck L-rod. Remove L-rods from
lift arms. At this point, deck will drop down.
5. Carefully raise and support front of chassis. Slide mower deck to either side for
removal. (Reverse procedure to reinstall deck assembly).
NOTE:
When deck is reinstalled on frame, check that belt is correctly routed
in the groves of all pulleys and that belt idler is applying tension to the
back side of the belt.
Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
HOT oil may cause burns.
Allow engine to cool before draining oil.
CAUTION
CHANGING THE ENGINE OIL:
1. The "snap lock" oil drain valve is located on the left side of the engine crankcase.
2. Place a suitable container under the drain valve. The fitting of a short piece of
hose to the valve will help direct the oil.
3. Push the valve body in and twist to clear the detent notch.
4. Pulling the valve body outward will start the flow of oil.
NOTE: Refer to engine manufacturers recommendations for frequency of oil changes.
Briggs & Stratton
Kohler
PLEASE DISPOSE OF USED OILS AT PROPER COLLECTION CENTERS.
-PROTECT YOUR ENVIRONMENT-
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
OIL FILL:
1. Push the valve body
in and twist into the
detent notch.
Closed
Open
2. Clean any spilled oil from engine and chassis.
3. Refill engine with type, and quantity of oil recommended by the engine
manufacturer in engine literature.
NOTE:
Oil changes require replacement of the oil filters. These filters can be obtained from
your authorized engine dealer.
The use of any other oil filter may cause damage to the engine.
Briggs & Stratton Oil Filter: P/N 492 932
Kohler Oil Filter: P/N 52 050 02
PLEASE DISPOSE OF USED OILS AT PROPER COLLECTION CENTERS.
-PROTECT YOUR ENVIRONMENT-
LUBRICATION:
CHASSIS:
Number of grease zerks used:
(6) for 36"
(7) for 42"
(7) for 50"
LOCATIONS:
(1) each front wheel caster tube and each front wheel hub.
(1) each mower deck hub.
SERVICE INTERVALS:
Every 50 hours of operation
RECOMMENDEDGREASE:
Name brand wheel bearing or multi-purpose grease
Lubricate each front wheel to allow even distribution of grease
within the wheel, rotate or spin each front wheel after (3) pumps
of the grease gun. Repeat process until the appearance of
grease is noted completely around each caster axle.
Page 32
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
WHEELS AND TIRES:
Correct tire pressure is important for correct operation of
mower.
Front Tires
Rear Tires
11 X 4.00 X 5
18 X 8.50 X 8
16-21 PSI
8-14 PSI
NOTE: Check lug nuts periodically for tightness.
ELECTRICAL SYSTEMS:
CLEANING THE MOWER:
Keep all connections clean and tight.
Wash mower periodically.
Clean above and below deck.
NOTE:
Allowmowertocoolbeforewashing. Ifbearingsare
hot, they will draw moisture inside as they dry and
cause corrosion.
SERIAL NUMBERS:
The serial number is located on frame at rear of engine, it will
begin with DM.
WARRANTY:
Refer to Warranty Registration Form (P/N 5859).
PARTS/SERVICE:
See your Dixon dealer for replacement parts, warranty or
service.
PLEASE HELP PROTECT THE ENVIRONMENT BY AVOIDING ALL
CHEMICALS WHICH MAY DAMAGE OR CAUSE HARM TO PLANTS AND
ANIMALS IN YOUR AREA.
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD SERVICE PARTS LIST
36" DECK:
42" DECK:
50" DECK"
BLADES:
BELTS:
Standard:
Hi-Lift:
P/N 1324
P/N 1351 Right Side
P/N 1352 Left Side
Engine To Mower Deck: P/N 1300
Engine To Transmission: P/N 5768
BLADES:
BELTS:
StandardHi-Lift:
Lo-Lift:
P/N 8688
P/N 6236
Engine To Mower Deck: P/N 5861
Serpentine Belt: P/N 6109
Engine To Transmission: P/N 5768
BLADES:
Standard Hi-Lift:
Lo-Lift:
P/N 9444
P/N 9443
BELTS:
Engine To Mower Deck: P/N 7174
Serpentine Belt: P/N 1300
Engine To Transmission: P/N 5768
BRIGGS & STRATTON FILTER PART NUMBERS:
Please refer to Briggs & Stratton Engine Operators Manual for correct service intervals for engine oil
changes and air filter maintenance.
Protect your engine investment, use only original equipment filters.
Precleaner Foam Element
Air Filter Cartridge:
Engine Oil Filter:
P/N 272 403
P/N 493 909
P/N 492 932
KOHLER FILTER PART NUMBERS:
Please refer to Kohler Engine Operators Manual for correct service intervals for engine oil changes
and air filter maintenance.
Protect your engine investment, use only original equipment filters.
Air Filter Cartridge:
Pre-Cleaner:
Engine Oil Filter:
P/N 12 08 310
P/N 12 08 312
P/N 52 050 02
Page 34
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
MOWER CUT QUALITY:
There are many variables that can effect the cut quality of any riding mower. Type and
conditionsofgrass, cutheightsetting, engineRPMandgroundspeedaresomeofthevariables
that interact creating differences in cut quality. Examination of one or more of the above will
generally produce a quality cut.
The Troubleshooting Chart suggests practices and adjustments that may be helpful in
improving cut quality. Your Dixon ZTR dealer is also available to provide assistance to you.
SITUATION
CAUSES
REMEDY
Poorcutquality
Groundspeed
Reduce mowing speed
Poor cut quality
Incorrect engine to
mower deck belt
Refer to page 31 for part numbers
Poor cut quality
Poor cut quality
Poor cut quality
Poor cut quality
Engine RPM too low
Dull or bent blade
Increase engine RPM to maximum
Sharpen or replace as required
Un-level mower deck
Refer to page 25 for deck leveling
procedure
Grass buildup under
mower deck
Clean out underside of mower deck
Poor cut quality
Poor cut quality
Improper blades
Refer to page 31 for part numbers
Uneven tire pressures
Refer to page 30 for correct tire
pressures
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
DRIVE SYSTEM:
SITUATION
CAUSES
REMEDY
Mower creeps in
neutral position
Neutraladjustment
Refer to page 24 for procedure or consult
your dealer for repair
Mower pulls to one
side or the other
Forward travel speed
adjustment
Refer to page 23 for procedure
Loss of power and
speed on both sides
.
Incorrect or worn drive
belt
Replace belt
Spring on idler arm
missing or broken
Replace spring
Idler arm will not pivot
Internal malfunction
Remove cause of seizure and lubricate
Consult your dealer for repairs
Drive system
Incorrect or worn drive
Replace belt
functions on one side belt
only
Spring on idler arm
Replace spring
missing or broken
Idler arm will not pivot
Remove cause of seizure and lubricate
Consult you dealer for repairs
Internal malfunction
Page 36
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
ELECTRICAL SYSTEM:
SITUATION
CAUSES
REMEDY
Starterwillnot
Circuit breaker
Pushbuttontoreset
turn engine over
disengaged
Consult your dealer for repair
Starter will not
Dead Battery
Charge battery
turn engine over
Battery discharge
Poor connections on
battery
Tighten or replace as required
Battery water low
Wrong battery installed
in mower
Battery discharge
Battery discharge
Engine electrical system Have electrical system checked by your
not functioning correctly dealer
Engine not being
Increase engine RPM
operated at full throttle
Contact your dealer for information
NOTE: Electricalsystemfailuresaregenerallysimpleinnature,alwayschecktheobviousfirst
and then move onto the more complicated parts used.
Poorbatteryservice, looseconnections, corrosion, frayedorbrokenwiring, aremore
likely than component failure.
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER
INFORMATION
DIXONINDUSTRIES,INC.
A BLOUNT International Inc. Co.
PO BOX 1569
COFFEYVILLE KS 67337 0945
316 251 2000
FAX 316 251 4117
DATE PURCHASED
MOWER MODEL NUMBER
MOWER SERIAL NUMBER
DM-
PURCHASED FROM
Name
Address
DATE OIL CHANGED:
DATE ENGINE TUNED:
Download from Www.Somanuals.com. All Manuals Search And Download.
The Engine Exhaust from this product contains chemicals known to the
State of California to cause cancer, birth defects or other reproductive harm.
WARNING:
® Dixon and ZTR are registered trademarks of Dixon Industries, Inc.
DIXON INDUSTRIES, INC.
A BLOUNT International Inc. Co.
PO BOX 1569
4500 Series
Part No. 5863-0798
COFFEYVILLE KS 67337 0945
316 251 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
|