Dimplex Fan FX 20VL User Manual

Installation and Operating Instructions  
Downflow Fan Heater  
Model FX 20VL  
08/30041/1  
Issue 1  
(IP22)  
Dimensions  
(millimetres)  
Model(s) Specification  
FX 20VL  
(Low Level) 1/2kw + Adjustable Thermostat (external by installer)  
Fig. 1  
SUPPLY CABLE IS NOT SUPPLIED WITH THIS APPLIANCE AND IT  
SHOULD THEREFORE BE INSTALLED BY COMPETENT  
ELECTRICIAN IN ACCORDANCE WITH THE IEE REGULATIONS.  
A
IMPORTANT SAFETY ADVICE  
WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE  
SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING POOL.  
The Controls  
THIS APPLIANCE CARRIES A WARNING ‘DO NOT COVER’ TO  
ALERT THE USER TO THE RISK OF OVERHEATING THAT EXISTS  
IF THE APPLIANCE IS ACCIDENTALLY COVERED.  
The cut-out is a safety device which switches off the heater and fan if for  
any reason the appliance overheats. (see ‘Safety’)  
DO NOT COVER THE APPLIANCE or place material or garments  
on it, or obstruct the air circulation around this appliance, for  
example with curtains or furniture, as this could cause  
overheating and a fire risk.  
The thermal fuse link is provided as an added safety feature, and  
operates to open circuit if there is abnormal overheating within the  
appliance. The operation of these safety devices is described under  
‘Safety’  
DO NOT PLACE AEROSOLS OR OTHER CONTAINERS  
SUSCEPTIBLE TO HEAT IN THE DIRECT AIRFLOW FROM THE  
UNIT.  
This model is also fitted with an adjustable thermostat which can be  
adjusted by user. This has the following settings : 0,  
, 1,  
* (frost protection)  
2, 3, 4, 5 (max). The thermostat should be set to 5 (max). Once the  
required room temperature is reached, it can be turned back until a click  
(switch off) can be heard, which will give you a constant room temperature  
with the thermostat switching on and off automatically. This gives you an  
approximate room temperature range of 7°C - 32°C depending on room  
size. Frost protection : When the temperature falls below + 5 … +8°C, the  
appliance switches on automatically.  
THIS HEATER MUST NOT BE LOCATED IMMEDIATELY BELOW A  
FIXED SOCKET OUTLET.  
WARNING – DISCONNECT THE HEATER FROM THE ELECTRICITY  
SUPPLY BEFORE UNDERTAKING SERVICE OR REPAIR.  
WARNING – If the appliance is fitted in a bathroom, a cable outlet  
will be necessary with the supply to the unit controlled by a  
double pole switch. The switch if inside the bathroom should be  
pull cord operated and if outside should be adjacent to the  
entrance door. The appliance must be mounted so that no part of  
it can be touched by any person using bath or shower.  
Note – On this model the thermostat works independent from the selected  
output.  
To reset the selector switch first remove the top cover, then adjust  
thermostat to required setting, or reset selector switch to 1kw or 2kw as  
required, then refit top cover.  
THIS HEATER MUST NOT BE OPERATED WITHOUT THE COVER  
CORRECTLY IN POSITION.  
Safety  
General  
Cut-Out  
For your safety, this appliance is fitted with a thermal cut-out. In the event  
that the product overheats, the cut-out switches the heater off  
automatically.  
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND  
RETAINED FOR FUTURE REFERENCE.  
To bring the heater back into operation, remove the cause of overheating,  
then turn off the electrical supply to the heater for a few minutes.  
When the heater has cooled sufficiently reconnect and switch on the  
heater.  
The heater has a loading of 2KW. It is designed for permanent wall  
mounting and is suitable for operation on A.C. electricity supply having the  
same voltage as shown on the rating label.  
The heater is fitted with an internally mounted selector switch which on  
installation of the heater allows a choice of 1kW or 2kW output to suit the  
dimensions of the room to be heated.  
Fuse Link  
A thermal fuse link is provided as an added safety feature. If the fuse link  
operates and opens circuit it is the result of abnormal overheating within  
the appliance, and servicing of the appliance by a competent service  
engineer will be required in order to ensure the future safe operation of the  
heater. Dimplex Customer Services should be contacted, who will arrange  
the replacement of any faulty parts and the fitting of a new fuse link.  
In rooms of less than 9 – 11 cubic m. (350 - 400 cubic ft.) 1kW output  
should be selected, otherwise nuisance tripping of the thermal overload  
cut-out may occur.  
NOTE  
:
THE SWITCH HAS BEEN FACTORY SET FOR 2kW  
OPERATION.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Coleman Camping Equipment 2000000850 User Manual
ConnectPRO Home Theater Server EOCVA1 User Manual
Craftsman Router 315175 User Manual
Craig Portable Multimedia Player CMP615D User Manual
Creek Audio Stereo Amplifier Wyndsor User Manual
Cyber Acoustics Speaker CA 31 User Manual
D Link Network Router VERSION 410 User Manual
Flymo Trimmer 450 User Manual
Garland Range C0836 12 User Manual
Generac Power Systems Portable Generator 9592 3 User Manual