Installation and Operation Manual
TM
PowerMax DA4KSBR-50U
60 dB Gain Dual Band
Wireless Amplifier/Repeater System
Read Instruction before installing!
If you do not understand instructions,
seek professional installation.
Digital Antenna, Inc.
>
5325 NW 108th Avenue
>
t 954.747.7022
>
>
Sunrise, FL 33351
>
f 954.747.7088
>
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
Read instructions completely before attempting install!
1. Package Contents
Part Number Description
DA4000SBR
288-PB
135-RD
Dual Band Wireless Cellular Amplifier/Repeater
Outside omni-directional 9dB gain dual band cell antenna
Inside omni-directional dual band cell antenna with stand & 18” cable
12 VDC to 5 VDC power cable
DP515
DP255
DA340-50NM
DH288
110-240 VAC to 5 VDC power supply
50' PowerMaxTM ULTRA low loss cable
Stainless steel mounting hardware: qty 2 U-bolts, nuts, washers; qty 4
philips head screws
2. Important Safety Information
The DA4000SBR system complies with all FCC, IC, UL rules, regulations and codes.
Follow all guidelines in the installation and instruction manual and read completely
before beginning the installation procedure. Do not deviate or disregard any of the safety
features included in the manual or with the equipment, nor operate the system in an
unintended application.
WARNING!
Only Digital Antenna authorized products may be used with the
DA4000SBR system. Using unauthorized equipment with the
DA4000SBR system will harm the system, voids the warranty and can be
detected in the event of a failure.
WARNING!
Do not install antenna near power lines. Contact with any high voltage
power lines could result in shock or loss of life.
WARNING!
Handle all electronic parts with care. Dropping or mishandling the
DA4000SBR amplifier/repeater, antennas or power supplies can damage
sensitive RF and electronic components.
3
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
a. LIMITED WARRANTY
Digital Antenna, Inc. warrants marine antennas for five (5) years and cellular antennas and amplifiers for one (1) year
that its Products sold hereunder will at the time of shipment be free from defects in material and workmanship and will
conform to Digital Antenna’s applicable specifications or, if appropriate, to Customer’s specifications previously
accepted by Digital Antenna in writing.
If products sold hereunder are not as warranted, Digital Antenna shall, at its option either refund the purchase price, or
repair or replace the product, provided proof of purchase and written notice of nonconformance are received by Digital
Antenna within five (5) or one (1) years of date of purchase and provided said nonconforming Products are, with
Digital Antenna’s written authorization, returned in protected shipping containers. Digital Antenna will pay for
transporting the repaired or exchanged product to Customer.
This warranty shall not apply to any Products Digital Antenna determined to have been, by Customer otherwise,
subjected to mishandling, misuse, neglect, improper testing, repair alteration, damage, assembly or processing that
alters physical or electrical properties.
b. LIMITATION ON LIABILITY
In no event shall Digital Antenna, Inc. Be liable for any direct, indirect, special, punitive, incidental, exemplary or
consequential damages, or any damages whatsoever, even if Digital Antenna, Inc. Has been previously advised of the
possibility of such damages, whether in an action under contract, negligence, or any other theory, arising out of or in
connection with the use, inability to use, or performance of the information, services, products, and materials available
from this manual. These limitations shall apply notwithstanding any failure of essential purpose of any limited remedy.
Because some jurisdictions do not allow limitations on how long an implied warranty lasts, or the exclusion or
limitation of liability for consequential or incidental damages, the above limitations may not apply to you.
c. FCC REGULATIONS
FCC ID: PZODA4000SBR
This equipment has been tested and found to comply with the limits for a class B device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in accordance with this instruction
manual, may cause harmful interference to radio communications, However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or other electronic
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of more of the following measures:
•
•
•
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect to isolated power with a ground cable going directly to the battery, DC source or house ground
Repositioning of the coaxial cable may also eliminate interference
Consult the dealer or an experienced electronics technician for help.
Warning: Changes or modifications not expressly approved by Digital Antenna, Inc. could void the user's authority to
operate the equipment.
4
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Pre-Installation Guidelines
a. INSTALLATION TOOLS
The following tools are required for installation:
• Standard wrench and philips head screwdriver
• Standard drill with ½” bit (optional)
• Cellular phone operating on 800 or 1900 MHz bands (any USA or Canadian
cellular phone except Nextel)
• Wire fasteners (optional)
• Multi-meter for testing electrical continuity and AC and DC line voltage (for
troubleshooting only)
b. INSTALLATION PROCEDURE
Description of DA4000SBR System
The DA4000SBR Dual Band Wireless Amplifier/Repeater system provides cellular
signal coverage to areas that have low signal strength to adequately operate a cellular
phone. In these poor coverage areas it becomes difficult to place or receive calls and
usually results in a dropped call. The DA4000SBR dual band amplifier/repeater system
provides increased reception indoors by filtering, re-directing and amplifying the
available signal. This translates into fewer dropped calls, safe, clear connections and
stronger signals. The DA4000SBR dual band system operates with all carriers in the USA
and Canada except Nextel. A
Cell Signal -90 to -70 dBm
P/N 288-PB
O u ts id e
A n te n n a
Cell Signal re-broadcasted
inside building through
DA4000SBR system
P/N C277-30
50' Cable
P/N 135-RD
Inside Antenna
Cell Site
P/N DA4000SBR
Amplifier/Repeater Unit
Cell Signal degraded
by exterior wall, distance
trees & foliage, etc....
Functional Operation of DA4000SBR System
Installation requirement: Separation Distance of 40' or more between outside and inside antennas
The DA4000SBR system contains a dual band low power indoor antenna,
amplifier/repeater unit and high gain omni-directional outdoor antenna. Both antennas
must be installed and operate in a vertical position. The indoor antenna must be used with
cable and stand. The outdoor omni-directional antenna, P/N 288-PB, is installed outside
5
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
of the building. (see specific section for Home/Office, marine and RV installations) The
omni-directional antenna should be installed on the side of the building with the strongest
cellular signal as indicated by the bars on the cell phone. The outside antenna must be
installed outside of the building, RV or boat. The inside antenna must be mounted in a
central location in the building that is 40’ or greater from the outside antenna. The inside
and outside antenna also must be separated by an exterior wall. Two power supplies are
included to maximize installation flexibility.
Typical In-Building Coverage
The DA4000SBR system is designed to provide optimal coverage for a 3,000 ft2 to 5,000
ft2 area. Interior coverage varies based upon the outside signal strength and the interior
building construction and materials. Typically the DA4000SBR system will penetrate 1-2
interior walls and 1 floor based upon construction material.
Pre-installation Considerations
Establish a site installation plan based upon desired central coverage area
• The inside and outside antenna must have a separation distance of 40 feet or
greater, the outside antenna must be outside and separated from the inside antenna
by an exterior wall, and both antennas must be in a vertical position.
• Identify the outside antenna location. If the outdoor coverage area is very poor,
the outside antenna should be placed on the side of the building where the signal
is the strongest. If the signal is equally strong outdoors, the outside antenna
should be placed in a secure, unobstructed area. On an RV the antenna can be
attached to the back ladder or on the side of the RV. On a boat the outside antenna
should be mounted clear of metal objects, 3’ from other antennas and as high as
possible.
• For maximum coverage the location of the indoor antenna should have a direct
line-of-site to as much of the coverage area as possible. The indoor antenna must
be used with 18” cable and antenna stand. Never use the inside antenna directly
connected to DA4000SBR amplifier/repeater unit.
• Based upon the desired coverage area, choose a central location for the
DA4000SBR unit. The location of the DA4000SBR unit must be accessible
within reach of the supplied 50’ cable (PowerMaxTM 25’ extension cable and
75’ replacement cables sold separately) and within 6’ of a power receptacle (or an
extension cord can be used). The DA4000SBR unit is not waterproof and must be
kept in a dry location.
c. ELECTRICAL POWER
To maximize installation flexibility, the DA4000SBR system includes 2 power cord
options.
WARNING!
Only the provided power cables are to be used with the DA4000SBR
system. Using any other power cables will harm the DA4000SBR
amplifier/repeater unit, can be detected and voids the warranty.
6
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
To plug into a standard 110 VAC receptacle use P/N DP255, a 110 VAC to 5VDC Power
Supply. For use on a boat or RV, plug P/N DP515, a 12 VDC to 5 VDC Power Cable,
into a 12 VDC cigarette style power receptacle.
d. AMPLIFIER/REPEATER STATUS
The DA4000SBR unit is designed with a status/fault indicator to indicate proper unit
functionality. The chart below details the different LED color indicators.
LED
Amplifier/Repeater Status
Normal Status
Degree of cellular transmission activity
Picture
Picture
Green solid light
Yellow/orange
flickering light
Solid Red light
No light
Picture
Picture
Fault needs immediate corrective action
No power to the DA4000SBR
amplifier/repeater or unit is defective
Green light – shows normal Status and DA4000SBR is operating normally. No
corrective action necessary.
Green/yellow/orange flickering light - shows that cellular activity is being transmitted
through the DA4000SBR unit. The light will remain green with low levels of cellular
transmission and change to flickering yellow/orange as transmission increases. The light
may remain green with low levels of transmission.
Solid Red light – indicates a fault. Turn OFF power switch and proceed with the
following corrective actions:
• The red light indicates that the inside and outside antennas are located too close to
each other and need to be re-located. A typical installation requires that the inside
and outside antennas have a minimum separation distance of 40 feet and be
separated by an exterior wall. If the inside and outside antennas are not 40 feet
apart or more, relocate the antennas.
• If the outside and inside antennas are separated by 40’ or more and an exterior
wall. The red light also indicates the use of analog phones.
No light – indicates missing power to the DA4000SBR unit. Proceed with the following
corrective actions:
• Verify that the power switch on the DA4000SBR unit is in the ON position.
• Test for 5VDC power – verify that 5VDC is available on the output plug of P/N
DP255 or DP515. If 5VDC is verified, the DA4000SBR unit may be defective.
See below
o Test for AC line voltage on the input plug of P/N DP255, 100 to 240VAC
to 5VDC Power Supply. If AC voltage is available and there is no 5VDC
on the output plug. The power supply is defective. See below
o Test for DC line voltage on the input plug of P/N DP515, 12 VDC to 5
VDC Power Cable. If input voltage is available and there is no 5VDC on
the output plug. The power cable is defective. See below
• DA4000SBR unit, DP255 or DP515 may be defective. Contact your dealer. The
serial number on the DA4000SBR unit must be available.
7
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
e. IN-BUILDING COVERAGE PROBLEMS
If the DA4000SBR unit does not indicate a red light and the coverage area appears to be
smaller than anticipated, one or more of the following may limit the signal strength to the
area.
• Cell Phone Bars - The bars on the cell phone do not indicate coverage area. One
bar may be adequate to successfully place and receive calls. Test coverage area by
successfully completing calls while disregarding bar indicator.
• Physical obstructions degrading the cell signal – the path of the cell signal is
weakened by objects. Large metal objects block or reflect the signal. Inspect the
coverage area, rearrange any objects in the path of the cell signal or relocate the
indoor antenna.
• Output Power Control – The DA4000SBR has an internal output power control
circuit that automatically lowers the power when the inside and outside antenna
are located too close. Verify that inside and outside antennas are located 30’ apart
or more and separated by an exterior wall.
• Cabling – examine coaxial cable run and verify that the cable is not kinked,
coiled or damaged. Re-locate cable to avoid kinks or coils. If supplied 50’ cable is
damaged contact your dealer. The serial number on the DA4000SBR unit must be
available.
f. COAXIAL CABLE RECOMMENDATIONS
The DA4000SBR system includes 50’ of Digital Antenna’s PowerMaxTM ULTRA low
loss cable and connectors for easy installation. If the installed application requires more
than the supplied cable, PowerMaxTM DA340 ULTRA low loss 25’ extension cable
and 75’ replacement cable are available. Only Digital antenna cable can be used to
complete the installation. Unauthorized cable usage can be detected and voids the
warranty.
8
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Home/Office Installation
Review pre-installation considerations and determine site installation plan.
1. Install supplied outside antenna (P/N 288-PB) to vertical surface or pole with
supplied hardware. Mount the outside antenna clear of metal objects and
obstructions. Outside antenna must be mounted in a vertical position.
WARNING!
Only Digital Antenna authorized products may be used with the
DA4000SBR system. Using unauthorized equipment will harm the
DA4000SBR system, can be detected and voids the warranty.
2. On supplied 50’ cable (P/N DA340-50NM) (or optional 25’ extension cable or
75’ replacement PowerMaxTM cable) attach N male connector to N female
connector on outside antenna. Secure cable to the side of the building with
appropriate fasteners (not supplied). Route cable according to site installation plan
to the DA4000SBR unit.
3. Attach mini-UHF male connector at the end of the supplied 50’ cable to
DA4000SBR unit on the port labeled outside antenna. Attach the 18” cable
attached to the inside antenna and stand to the port labeled inside antenna. The
inside antenna must be operated in a vertical position.
4. The DA4000SBR unit has four mounting holes that can be fastened to a secure
surface. (fastening hardware not included) When mounting the DA4000SBR unit
the inside antenna must be in a vertical position.
5. Plug 100-240VAC power supply to the DA4000SBR unit. Plug the other end into
standard household 110VAC receptacle.
6. Turn the power switch to ON. If the light on the DA4000SBR unit is green then
the DA4000SBR system is operating. Test the amplifier/repeater system by
making a cell call and verifying that the indicator light does not turn red. If the
light on the DA4000SBR unit turns red immediately turn OFF the DA4000SBR
unit and refer to the Amplifier/Repeater status section.
Coverage Area
indicated by yellow
Amplifier/Repeater
Unit
Inside Coverage area is based upon outside signal strength.
A weak outside signal (-90dB) will provide less inside
coverage area than a stronger outside signal (-70dB).
9
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Marine Installation
Review pre-installation considerations and determine site installation plan.
1. Install supplied outside antenna (P/N 288-PB) to vertical surface or pole with
supplied hardware. Mount the outside antenna clear of metal objects and
obstructions and as high as possible. Outside antenna must be mounted in a
vertical position. The DA4000SBR system may also be used with one of Digital
Antenna’s marine 9dB gain dual band cellular antennas. (Follow minimum 40’
Inside and Outside antenna separation guideline)
WARNING!
Only Digital Antenna authorized products may be used with the
DA4000SBR system. Using unauthorized equipment will harm the
DA4000SBR system, can be detected and voids the warranty.
2. On supplied 50’ cable (P/N DA340-50NM) (or optional 25’ extension cable or
75’ replacement PowerMaxTM cable) attach N male connector to N female
connector on outside antenna. Secure cable to the side of the building with
appropriate fasteners (not supplied). Route cable according to site installation plan
to the DA4000SBR unit.
3. Attach mini-UHF male connector at the end of the supplied 50’ cable to
DA4000SBR unit on the port labeled outside antenna. Attach the 18” cable
attached to the inside antenna and stand to the port labeled inside antenna. The
inside antenna must be operated in a vertical position.
4. The DA4000SBR unit has four mounting holes that can be fastened to a secure
surface. (fastening hardware not included) When mounting the DA4000SBR unit
the inside antenna must be in a vertical position.
5. When using 110VAC - Plug 100-240VAC power supply to the DA4000SBR unit.
Plug the other end into standard 110VAC receptacle.
When using 12VDC – Plug the 12 VDC to 5 VDC power cable (P/N DP515) into
the DA4000SBR unit. Plug the other end into a 12VDC cigarette style power
source.
WARNING!
To have DC power hardwired consult a professional electronic technician.
6. Turn the power switch to ON. If the light on the DA4000SBR unit is green then
the DA4000SBR system is operating. Test the amplifier/repeater system by
making a cell call and verifying that the indicator light does not turn red. If the
light on the DA4000SBR unit is red immediately turn OFF the DA4000SBR unit
and refer to the Amplifier/Repeater status section.
10
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
6. RV Installation
Review pre-installation considerations and determine site installation plan.
1. Install supplied outside antenna (P/N 288-PB) to vertical surface or pole with
supplied hardware. Outside antenna must be mounted in a vertical position.
Mount the outside antenna clear of metal objects and obstructions and as high as
possible but take care not to exceed height of other roof mounted items such as
A/C.
WARNING!
Only Digital Antenna authorized products may be used with the
DA4000SBR system. Using unauthorized equipment with the
DA4000SBR system will harm the system, can be detected and voids the
warranty.
2. On supplied 50’ cable (P/N C277-30) (or optional 25’ extension cable or 75’
replacement PowerMaxTM cable) attach N male connector to N female
connector on outside antenna. Secure cable to the side of the building with
appropriate fasteners (not supplied). Route cable according to site installation plan
to the DA4000SBR unit.
3. Attach mini-UHF male connector at the end of the supplied 50’ cable to
DA4000SBR unit on the port labeled outside antenna. Attach the 18” cable
attached to the inside antenna and stand to the port labeled inside antenna. The
inside antenna must be operated in a vertical position.
4. The DA4000SBR unit has four mounting holes that can be fastened to a secure
surface. (fastening hardware not included) When mounting the DA4000SBR unit
the inside antenna must be in a vertical position.
5. When using 110VAC - Plug 100-240VAC power supply to the DA4000SBR unit.
Plug the other end into standard 110VAC receptacle.
When using 12VDC – Plug the 12 VDC to 5 VDC power cable (P/N DP515) into
the DA4000SBR unit. Plug the other end into a 12VDC cigarette style power
source.
WARNING!
To have DC power hardwired consult a professional electronic technician.
6. Turn the power switch to ON. If the light on the DA4000SBR unit is green then
the DA4000SBR system is operating. Test the amplifier/repeater system by
making a cell call and verifying that the indicator light does not turn red. If the
light on the DA4000SBR unit is red immediately turn OFF the DA4000SBR unit
and refer to the Amplifier/Repeater status section.
11
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Specifications
Amplifier/Repeater Unit P/N DA4000SBR
• Frequency:
Uplink: 824-849 MHz and 1850-1910 MHz
Downlink: 869-895 MHz and 1930-1990 MHz
• Modulations: AMPS/GPRS/TDMA/PCS/CDMA/GSM850/GSM1900
• Max Output Power: 3W (824-849 MHz), 2W (1850-1910 MHz)
• Dynamic Variable Gain: 60dB Max
• Impedance: 50 ohms
• Noise Figure: < 10dB
• Power Consumption: Standby 5 vdc/0.5A, Uplink 5 vdc/1.5A
• Internal Fuse: 3A
• FCC approved, FCC ID: PZODA4000SBR
• Industry Canada approved, IC ID: 4260A-DA4000SBR
• Dimensions: 4.5" l x 4.0" w x 1.25" h (114mm x 102mm x 32mm)
• Weight: 12 oz (.345 kg)
• RF Connections:
Outside Antenna Port: Mini-UHF Female
Inside Antenna Port: Mini-UHF Female
DC Power: Coaxial ID = 2.5mm, OD = 5.5mm (center positive)
• Indicator: Multi color status indicator
• Power Switch: Slide switch toward LED = ON
Outside Antenna P/N 288-PB
• Radiation pattern: Omni-directional
• Gain: 9 dBi
• VSWR: < 1.5:1 @ 850 MHz; < 1.5:1 @ 1900 MHz
• Bandwidth VSWR: < 1.5:1 = 810-950 and 1800-1980 MHz
• Max input power: 250 watts
• Dimensions: 18" l x .75” OD ( 45.7 cm x .2 cm )
• Weight:
• RF connector: N female
• Wind rating: 121.8 mph
• Installation: supplied L-bracket and hardware wall or pole
Inside Antenna P/N 135-RD
• Radiation pattern: Omni-directional
• Gain: Unity
• VSWR: < 1.5:1 @ 850 MHz; < 1.5:1 @ 1900 MHz
• Bandwidth VSWR: < 1.5:1 = 810-950 and 1800-1980 MHz
• Max input power: 50 watts
• Dimensions: 3.5" l x .25” OD ( 45.7 cm x .2 cm )
• Weight:
• RF connector: mini-UHF male
• Installation: Freestanding mount with 18” cable
12
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable P/N DA340-50NM
• Length: 50’
• Impedance: 50 Ohm
• RF connectors: N male and mini-UHF male factory attached
• Attenuation at 800 MHz: 2.5 dB per 30’
• Attenuation at 1900 MHz: 5.5 dB per 30’
Power Supply P/N DP255
• Input: 100-240VAC 50/60 Hz
• Output: 5VDC 1.5A
• Mounting: Wall type
• Cord Length: 10’ (3m)
• Output plug: 5.5 x 2.5 x 11mm
Power Cable P/N DP515
• Input: +/- 9VDC to +/- 24 VDC
• Output: 5VDC 1.5A
• Center Positive, smooth cable positive
• Connector: Cigarette lighter style
• Internal fuse: 3A
• Cord Length: 76” (1.93m)
• Output plug: 5.5 x 2.5 x 11mm
8. Antenna & Accessory Options
Outside Dual Band Cellular Antennas
For complete antenna specs
White
P/N
Black
P/N
Digital Antenna’s 500 series antennas include:
20’ cable, mount 1”-14 threads, high-gloss finish
2.5' Dual Band 9dB Gain Cellular Antenna
4' Dual Band 9dB Gain Cellular Antenna
8' Dual Band 9dB Gain Cellular Antenna
561-CW 561-CB
563-CW 563-CB
567-CW 567-CB
Digital Antenna’s 800 series antennas include:
female N connector, mount 1”-14 threads, high-gloss finish
2.5' Dual Band 9dB Gain Cellular Antenna w/ male 1"-14
4' Dual Band 9dB Gain Cellular Antenna w/ male 1"-14
8' Dual Band 9dB Gain Cellular Antenna w/ male 1"-14
854-CW 854-CB
883-CW 883-CB
897-CW 897-CB
Digital Antenna’s 800 series antennas include:
female N connector, mount wall/pole, high-gloss finish
2.5' Dual Band 9dB Gain Cellular Antenna w/ wall-pole base
4' Dual Band 9dB Gain Cellular Antenna w/ wall-pole base
8' Dual Band 9dB Gain Cellular Antenna w/ wall-pole base
996-CW 996-CB
962-CW 962-CB
967-CW 967-CB
Description
P/N
25’ PowerMaxTM ULTRA low loss extension cable w/
CA340-25NM
connectors (attaches to included 50’ cable)
75’ PowerMaxTM ULTRA low loss cable w/ connectors
DA340-75NM
13
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
Ferrule for mounting P/N 288-PB on 1”x14 male threads
2-way Cellular Combiner w/ mini-UHF female connectors
Dash/wall mount adapter cable 5’ length
F114 (available 7/01/04)
DA-2100
C428-05
Digital Antenna manufacturers cellular amplifiers, repeaters and antennas for the best
communication on land or sea. All products are designed, engineered and manufactured
product line.
9. Technical Support
Read Product FAQs on Digital Antenna’s website prior to calling Tech Support.
www.DigitalAntenna.com. Locate the Digital Antenna Inc. serial number on the
DA4000SBR unit before calling. The serial number is located on the bottom of the
DA4000SBR unit. The DA4000SBR serial number must be available to authorize
technical support and/or establish a return authorization. For installation technical support
contact your dealer. For system warranty issues contact Digital Antenna Technical
Support between the hours of 9:00 AM and 5:00 PM EST, at 954-747-7022 or e-mail
[email protected]. The DA4000SBR system must be used with Digital
Antenna authorized equipment. The technical support team will only support Digital
Antenna authorized equipment. Contact your dealer for installation questions.
14
wpsantennas.com
Digital Antenna, Inc Dealer / Master Distributor
(877) 594-5766
Download from Www.Somanuals.com. All Manuals Search And Download.
|