Hardware Reference Manual
Digi One EM
90000278_B
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
LEDs ..............................................................................................11
Cautions .........................................................................................13
DB-9 Serial Interface (P1) .............................................................15
Reset Switch (SW1).......................................................................16
Power Jack (P7) .............................................................................17
LEDs (CR4 - CR11) .....................................................................18
Digi One EM Hardware Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B Digi One EM Certifications
21
FCC Part 15 Class A......................................................................21
ICES 003 Class A ..........................................................................22
Product Safety................................................................................22
4
Digi One EM Hardware Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
I n t r o d u c t i o n
About This Guide
Purpose
The purpose of this guide is to enable developers to integrate
the Digi One EM into other devices, enabling these devices to
make use of the Digi One EM’s rich networking features.
Audience
Scope
This document is written for developers tasked with
integrating Digi One EM device servers into other devices.
This document provides the information required for electrical
integration of the Digi One EM into another device. It does
not address how to configure or administer the device server
or how to write applications to use its functionality. These
topics are covered in other documents in the library.
Digi One EM Hardware Reference
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Introducing the Digi One EM
Product Overview
The Digi One EM is part of the Digi One Family of single port
device servers that provide simple, reliable and cost-effective
network connections for serial devices. The Digi One EM
provides fully transparent serial device connectivity over
industry-standard Ethernet connections and allows both
equipment manufacturers and systems integrators to
network-enable products at a fraction of the time and cost
required to develop a custom solution. It is a highly flexible
and compact single component solution with a robust on-
board TCP/IP stack and 10/100 Base-T Ethernet support.
From medical systems to building control and industrial
automation, in virtually any application where embedded
serial connectivity over Ethernet is needed, the Digi One EM
is the ideal choice, delivering high-performance functionality.
Cautions
• To guard against damage to the Digi One EM due to elec-
trostatic discharge (ESD), do not remove it from its pro-
tective packaging until you have been properly grounded.
To ground yourself, put the wrist strap on (included in the
package) and then attach the clip to a metal surface.
• Input voltage for the Digi One EM must be in the range of
5VDC to 9VDC.
6
Digi One EM Hardware Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Support Information
To get help with a question or technical problem or to make
comments and recommendations about our products or
documentation, use the following contact information.
General
Digi International
11001 Bren Road East
Minnetonka, MN 55343
U.S.A
Customer Service and Support
United States: 1 877-912-3444
Other Locations: 1 952-912-3444
Digi One EM Hardware Reference
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connectors: Power and Serial Interface (P4)
The Digi One EM has a single 12-pin, serial interface port
(labeled P4) that supports EIA-232 (TTL levels only), data
rates up to 230 Kbps and full-modem control. The following
figure helps you locate pins, and the table helps you identify
which signal uses each pin.
Pin
Signal Name
Description
+5VDC to
+9VDC (input
only)
1
Input power to Digi One EM
2
GND
Reference Ground for input power
Receive Data (input)
Transmit Data (output)
Request To Send
Data Terminal Ready
Clear To Send
3
RxD
4
TxD
5
RTS
6
DTR
7
CTS
8
DCD
Data Carrier Detect
Data Set Ready
Reset
9
DSR
10
11
12
RST~
Reserved
Reserved
Not used
Not used
Digi One EM Hardware Reference
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connectors: Ethernet Interface (P1)
The Digi One EM Ethernet connector is an eight-wire, RJ-45
jack meeting the requirements of ISO 8877 for 10/100Base-
T. The following figure helps you locate pins and the table
helps you identify which signal uses each pin.
Pin
Signal Name
1
2
3
4
5
6
7
8
TxD+ (Transmit Data)
TxD- (Transmit Data)
RxD+ (Receive Data)
Not used
Not used
RxD- (Receive Data)
Not used
Not used
10
Digi One EM Hardware Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Reset Switch
The reset switch, located between P3 and CR1, does the
following (depending on how long you hold the switch down):
• It reboots the Digi One EM if you press and release the
switch immediately.
• It reboots the Digi One EM and restores the configuration
to factory defaults. (Press and hold the switch down for
about 20 seconds while powering the Digi One EM up.)
LEDs
Digi One EM LEDs provide information on port activity,
diagnostics, and Ethernet activity.
LED
Color
Function
Interpretation
•
•
Off means that the serial
channel is idle.
Blinking indicates an
active connection.
Indicates serial
port activity
Top left
Green
•
•
Off means that no link
has been detected.
On means that a link
has been detected.
Top
right
Network link sta-
tus
Green
Digi One EM Hardware Reference
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LED
Color
Function
Interpretation
•
•
Blinking 1-1-1 means
starting the operating
system.
Blinking 1-5-1 means
configuration has been
returned to factory
defaults.
Bottom
left
Red
Diagnostics
•
Steady blinking means
the device is seeking an
IP address from a
DHCP server.
Note: If other blinking
patterns occur, call Digi
Technical Support.
Bottom
right
Yellow
Reserved
NA
12
Digi One EM Hardware Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Overview
from your device to the Digi One EM module. See "DB-9
the Digi One EM.
Switch (SW1)" on page 16.
from a regulated power supply. See "Power Jack (P7)" on
page 17.
•
Eight LEDs. One (labeled CR4) tells you if the power is
on. The other seven (labeled CR5 - CR11) are active
when EIA-232 signals are detected. See "LEDs (CR4 -
CR11)" on page 18.
• A reserved 3-pin header (labeled P5)
Cautions
• Although the Digi One EM can handle up to 9 VDC, this
voltage can harm the development board, which works
only with the 5 volt regulated power supply. The board
does not regulate power.
• To guard against damage to the development board due
to electrostatic discharge (ESD), do not remove it from its
protective packaging until you have been properly
grounded. To ground yourself, put the wrist strap on
(included in the package) and then attach the clip to a
metal surface.
Digi One EM Hardware Reference
13
Download from Www.Somanuals.com. All Manuals Search And Download.
DB-9 Serial Interface (P1)
The following figure helps you locate specific DB-9 pins and
the table maps signals to pins.
Pin 5
Pin 9
Pin 1
Pin 6
Pin
Signal
1
2
3
4
5
6
7
8
9
Data Carrier Detect (DCD)
Receive Data (RxD)
Transmit Data (TxD)
Data Terminal Ready (DTR)
Signal/Chassis Ground (GND)
Data Set Ready (DSR)
Request To Send (RTS)
Clear To Send (CTS)
Unused
Digi One EM Hardware Reference
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Jack (P7)
The power jack accepts 5 volts DC +/- 5% from a regulated
power supply. The development board is polarity sensitive.
The +5 volts is assumed to be the center contact on
connector, and the ground is the outside of the connector
barrel, as shown in the following figure.
Digi One EM Hardware Reference
17
Download from Www.Somanuals.com. All Manuals Search And Download.
LEDs (CR4 - CR11)
The LED labeled CR4 is a power indicator. The other seven
LEDs display EIA-232 signal activity. The following table
describes the specific signal associated with each LED.
LED
Signal
CR5
Tx (Transmit Data)
CR6
CR7
CR8
CR9
CR10
CR11
Rx (Receive Data)
CTS (Clear to Send)
RTS (Request to Send)
DTR (Data Terminal Ready)
DSR (Data Set Ready)
DCD (Data Carrier Detect)
18
Digi One EM Hardware Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
S a m p l e A p p l i c a t i o n : T T L S i g n a l s t o
E I A - 2 3 2
The following figure is an example of how to convert the Digi
One EM signals to normal serial voltage levels.
9
D B
2
1
Digi One EM Hardware Reference
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A D i g i O n e E M S p e c i f i c a t i o n s
Network Interfaces
• RJ-45 connector
• 10/100Base-T
• Half- and full-duplex support
Serial Interface
One TTL EIA-232 serial interface
Data Rates (bps)
110, 134, 150, 200, 300, 600, 1200, 2400, 3600, 4800, 9600,
19200, 38400, 57600, 115200, 230400
Modem Control
DTR, DSR, DCD
Flow Control Options
RTS/CTS, DTR/DSR, XON/XOFF, None
Environmental
• Operating Temperature: 50 0F to 131 0F (10 0C to 55 0C)
• Humidity: 5% to 90%
• Altitude: 12,000 feet (3657.60 meters)
Power Requirements
+5VDC @ 370 mA to 9VDC @ 230 mA typical
Mechanical
• Length: 1.93 inches (49.02 millimeters)
• Width: 1.57 inches (39.87 millimeters)
• Height: 0.974 inches (24.73 millimeters)
20
Digi One EM Hardware Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B D i g i O n e E M C e r t i f i c a t i o n s
This product complies with the following standards:
FCC Part 15 Class A
Radio Frequency Interference (RFI) (FCC 15.105)
This equipment has been tested and found to comply with the
limits for Class A digital devices pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
environment. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used
in accordance with the instruction manual, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try and correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Labeling Requirements (FCC 15.19)
This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Digi One EM Hardware Reference
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Modifications (FCC 15.21)
Changes or modifications to this equipment not expressly
approved by Digi may void the user’s authority to operate this
equipment.
ICES 003 Class A
This Class A digital apparatus meets the requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la Classe A respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
Product Safety
• UL 60950
• EN60950
• CSA 22.2 No. 60950
22
Digi One EM Hardware Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Digi One EM Hardware Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Digi One EM Hardware Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
|